gpio: aspeed: Use a cache of output data registers
The current driver does a read/modify/write of the output registers when changing a bit in __aspeed_gpio_set(). This is sub-optimal for a couple of reasons: - If any of the neighbouring GPIOs (sharing the shared register) isn't (yet) configured as an output, it will read the current input value, and then apply it to the output latch, which may not be what the user expects. There should be no bug in practice as aspeed_gpio_dir_out() will establish a new value but it's not great either. - The GPIO block in the aspeed chip is clocked rather slowly (typically 25Mhz). That extra MMIO read halves the maximum speed at which we can toggle the GPIO. This provides a significant performance improvement to the GPIO based FSI master. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Reviewed-by: Christopher Bostic <cbostic@linux.vnet.ibm.com> Reviewed-by: Andrew Jeffery <andrew@aj.id.au> Tested-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This commit is contained in:
parent
af79492849
commit
ed5cab43f9
|
@ -54,6 +54,8 @@ struct aspeed_gpio {
|
|||
u8 *offset_timer;
|
||||
unsigned int timer_users[4];
|
||||
struct clk *clk;
|
||||
|
||||
u32 *dcache;
|
||||
};
|
||||
|
||||
struct aspeed_gpio_bank {
|
||||
|
@ -231,12 +233,13 @@ static void __aspeed_gpio_set(struct gpio_chip *gc, unsigned int offset,
|
|||
u32 reg;
|
||||
|
||||
addr = bank_val_reg(gpio, bank, GPIO_DATA);
|
||||
reg = ioread32(addr);
|
||||
reg = gpio->dcache[GPIO_BANK(offset)];
|
||||
|
||||
if (val)
|
||||
reg |= GPIO_BIT(offset);
|
||||
else
|
||||
reg &= ~GPIO_BIT(offset);
|
||||
gpio->dcache[GPIO_BANK(offset)] = reg;
|
||||
|
||||
iowrite32(reg, addr);
|
||||
}
|
||||
|
@ -851,7 +854,7 @@ static int __init aspeed_gpio_probe(struct platform_device *pdev)
|
|||
const struct of_device_id *gpio_id;
|
||||
struct aspeed_gpio *gpio;
|
||||
struct resource *res;
|
||||
int rc;
|
||||
int rc, i, banks;
|
||||
|
||||
gpio = devm_kzalloc(&pdev->dev, sizeof(*gpio), GFP_KERNEL);
|
||||
if (!gpio)
|
||||
|
@ -892,6 +895,20 @@ static int __init aspeed_gpio_probe(struct platform_device *pdev)
|
|||
gpio->chip.base = -1;
|
||||
gpio->chip.irq.need_valid_mask = true;
|
||||
|
||||
/* Allocate a cache of the output registers */
|
||||
banks = gpio->config->nr_gpios >> 5;
|
||||
gpio->dcache = devm_kzalloc(&pdev->dev,
|
||||
sizeof(u32) * banks, GFP_KERNEL);
|
||||
if (!gpio->dcache)
|
||||
return -ENOMEM;
|
||||
|
||||
/* Populate it with initial values read from the HW */
|
||||
for (i = 0; i < banks; i++) {
|
||||
const struct aspeed_gpio_bank *bank = &aspeed_gpio_banks[i];
|
||||
gpio->dcache[i] = ioread32(gpio->base + bank->val_regs +
|
||||
GPIO_DATA);
|
||||
}
|
||||
|
||||
rc = devm_gpiochip_add_data(&pdev->dev, &gpio->chip, gpio);
|
||||
if (rc < 0)
|
||||
return rc;
|
||||
|
|
Loading…
Reference in a new issue