All of these CSRs have the same read/ write/ aynthing-else handling,
except for CSR_PRIORITY_BUDGET which might not be implemented.
The CSR_CYCLE_TIME read handler implementation accepted 4-byte-sized
block write requests before this change but this is just silly; the
register is only required to support quadlet read and write requests
like the other r/w CSR core and Serial-Bus-dependent registers.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Push the maintenance of STATE_CLEAR/SET.abdicate down into the card
driver. This way, the read/write_csr_reg driver method works uniformly
across all CSR offsets.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
by feature variables in the fw_card struct. The hook appeared to be an
unnecessary abstraction in the card driver interface.
Cleaner would be to pass those feature flags as arguments to
fw_card_initialize() or fw_card_add(), but the FairnessControl register
is in the SCLK domain and may therefore not be accessible while Link
Power Status is off, i.e. before the card->driver->enable call from
fw_card_add().
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
In case of fw_card_bm_work()'s lock request, the present sizeof
expression is going to be wrong if somebody changes the fw_card's DMA
scratch buffer's size in the future.
In case of quadlet write requests, sizeof(u32) is just silly; it's 4.
In case of SBP-2 ORB pointer write requests, 8 is arguably quicker to
understand as the correct and only possible value than
sizeof(some_datum).
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Add a comment on which of the conflicting NODE_IDS specifications we
implement. Reduce a comment on rather irrelevant register bits that can
all be looked up in the spec (or from now on in the code history).
Directly include the required indirectly included bug.h.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
As part of the bus manager responsibilities, make sure that the cycle
master sends cycle start packets. This is needed when the old bus
manager disabled the cycle master's cmstr bit and there are iso-capable
nodes on the new bus.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
On OHCI 1.1 controllers, let the hardware allocate the broadcast channel
automatically. This removes a theoretical race condition directly after
a bus reset where it could be possible to read the channel allocation
register with channel 31 still being unallocated.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Implement the abdicate bit, which is required for bus manager
capable nodes and tested by the Base 1394 Test Suite.
Finally, something to do at a command reset! :-)
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Implement the cmstr bit, which is required for cycle master capable
nodes and tested for by the Base 1394 Test Suite.
This bit allows the bus master to disable cycle start packets; there are
bus master implementations that actually do this.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Implement the MAIN_UTILITY register, which is utterly optional
but useful as a safe target for diagnostic read/write/broadcast
transactions.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
If supported by the OHCI controller, implement the PRIORITY_BUDGET
register, which is required for nodes that can use asynchronous
priority arbitration.
To allow the core to determine what features the lowlevel device
supports, add a new card driver callback.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Implement the BUS_TIME register, which is required for cycle master
capable nodes and tested for by the Base 1393 Test Suite. Even when
there is not yet bus master initialization support, this register allows
us to work together with other bus masters.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
The specification requires that CYCLE_TIME is writable so that it can be
initialized, so we better implement it.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Implement the SPLIT_TIMEOUT registers. Besides being required by the
spec, this is desirable for some IIDC devices and necessary for many
audio devices to be able to increase the timeout from userspace.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
The NODE_IDS register, and especially its bus_id field, is quite
useless because 1394.1 requires that the bus_id field always stays
0x3ff. However, the 1394 specification requires this register on all
transaction capable nodes, and the Base 1394 Test Suite tests for it,
so we better implement it.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
To prepare for the following additions of more OHCI-implemented CSR
registers, replace the get_cycle_time driver callback with a generic
CSR register callback.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
The state registers are zero and read-only in this implementation, so
they are not of much use. However, the specification requires that they
are present for transaction capable nodes, and the Base 1394 Test Suite
tests for them, so we better implement them.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
When the candidate bus manager fails to do the lock request with which
it tries to become bus manager, it assumes that the current IRM is not
actually IRM capable and forces itself to become root. However, if that
lock request failed because the local node itself was not able to send
it, then we cannot blame the current IRM and should not steal its
rootness.
In this case, RCODE_SEND_ERROR is likely to indicate a temporary error
condition such as exhausted tlabels or low memory, so we better try
again later.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Most PHY chips, when idle, can complete a register access in the time
needed for two or three PCI read transactions; bigger delays occur only
when data is currently being moved over the link/PHY interface. So if
we busy-wait a few times when waiting for the register access to finish,
it is likely that we can finish without having to sleep.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Add a check that the data length in the SEND_RESPONSE ioctl is correct.
Incidentally, this also fixes the previously wrong response length of
software-handled lock requests.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
This patch adds support for message-signaled interrupts.
Any native PCI-Express OHCI controller should support MSI, but most are
just PCI cores behind a PCI-E/PCI bridge. The only chips that are known
to claim to support MSI are the Lucent/Agere/LSI FW643 and the VIA
VT6315, none of which I have been able to test.
Due to the high level of trust I have in the competence of these and any
future chip makers, I thought it a good idea to add a disable-MSI quirk.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Tested Agere FW643 rev 07 [11c1:5901] and JMicron JMB381 [197b:2380].
Added a quirks list entry for JMB38X since it kept its count of MSI
events consistently at zero.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
On 26 Apr 2010, Clemens Ladisch wrote:
> In theory, none of the interrupts should occur before the link is
> enabled. In practice, I'd rather make sure to not set the master
> interrupt enable bit until we have installed the interrupt handler.
and proposed to move OHCI1394_masterIntEnable out of the present
reg_write() into a new one before the HCControl.linkEnable reg_write().
Why not defer setting /all/ of the bits until right before linkEnable?
Reviewed-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Using a single timeout for all transaction that need to be flushed does
not work if the submission of new transactions can defer the timeout
indefinitely into the future. We need to have timeouts that do not
change due to other transactions; the simplest way to do this is with a
separate timer for each transaction.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (+ one lockdep annotation)
fw_core_handle_response() was not properly clearing tlabel_mask. This
was resulting in premature tlabel exhaustion.
Signed-off-by: Peter Hurley <phurley@charter.net>
This fixes an omission in 2.6.31-rc1 commit 1e626fdc "firewire: core:
use more outbound tlabels" which prevented to really use 64 instead of
32 transaction labels, as soon as split transactions occurred that had
their AR-resp tasklet run after the AT-req tasklet.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
If one request is so long-lived that it does not get a response before
the following 63 requests, its bit in tlabel_mask is still set when the
next request tries to allocate a transaction label for that number. In
this state, while the first request is not completed or timed out, no
new requests can be submitted.
To fix this, skip over any label still in use, and do not error out
unless we have entirely run out of labels.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Clemens Ladisch pointed out that
- BIB_IMC is not named like the field is called in the standard,
- readers of the code may get worried about the magic 0x0c0083c0,
- a CSR_NODE_CAPABILITIES key is there in the header but not put to
good use.
So let's rename BIB_IMC, add a defined constant for Node_Capabilities
and a comment which reassures people that somebody thought about it and
they don't have to (or if they still do, tell them where they have to
look for confirmation), and prune our incomplete and arbitrary set of
defined constants of CSR key IDs. And there is a nother magic number,
that of Bus_Information_Block.Bus_Name, to be defined and commented.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The <linux/firewire-cdev.h> character device file ABI (i.e. /dev/fw*
character device file interface) does not make any use of lseek(),
pread(), pwrite() (or any kind of write() at all).
Use nonseekable_open() and, redundantly, set file_operations.llseek to
no_llseek to remove any doubt whether the BKL-grabbing default_llseek
handler is used. (Also shuffle file_operations initialization according
to the order of handler definitions.)
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
1) Clean up two function names: The ohci_ prefix is only used in names
of fw_card_driver hooks. There were two unnecessary exceptions.
2) Replace empty macros by empty inline functions so that call parameter
type checking is available in #ifndef'd builds.
3) CONFIG_FIREWIRE_OHCI_DEBUG is currently a hidden kconfig variable,
hence is not going to be switched off by anybody. Still, it can be
switched off but then compilation will fail in ohci_enable() at the
expression param_debug & OHCI_PARAM_DEBUG_BUSRESETS. Add the necessary
definitions in the nonstandard case.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Rather than having the arbitrary msleep(2) pause, let read_phy_reg()
loop until the link--phy access was finished.
Factor write_phy_reg() out of ohci_update_phy_reg() and of
read_paged_phy_reg() and let it loop too until the link--phy access was
finished.
Like in the older ohci1394 driver, a timeout of 100 milliseconds is
chosen. Unlike the old driver, we sleep instead of busy-wait in each
waiting loop iteration. Instead of a loop, the waiting could probably
also be implemented interrupt driven, but why bother. It would require
up and running interrupt handling before the link was fully configured
and enabled.
Also modify functions a bit: Error return and value return can be
combined in read_phy_reg() since the domain of values is only u8.
Likewise in read_paged_phy_reg().
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
On TI chips (OHCI-Lynx and later), enable link enhancements features
that TI recommends to be used. None of these are required for proper
operation, but they are safe and nice to have.
In theory, these bits should have been set by default, but in practice,
some BIOS/EEPROM writers apparently do not read the datasheet, or get
spooked by names like "unfair".
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The OHCI spec says that, if the programPhyEnable bit is set, the driver
is responsible for configuring the IEEE1394a enhancements within the PHY
and the link consistently. So do this.
Also add a quirk to allow disabling these enhancements; this is needed
for the TSB12LV22 where ack accelerations are buggy (erratum b).
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The interrupt status bits in PHY register 5 are cleared by writing a one
bit. To avoid clearing them unadvertently, do not write them back when
they were read as set, but only when they have been explicitly requested
to be set.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Move the register reading code from ohci_update_phy_reg() into
a function which can be used separately.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
A userspace client got to see uninitialized stack-allocated memory if it
specified an _IOC_READ type of ioctl and an argument size larger than
expected by firewire-core's ioctl handlers (but not larger than the
core's union ioctl_arg).
Fix this by clearing the requested buffer size to zero, but only at _IOR
ioctls. This way, there is almost no runtime penalty to legitimate
ioctls. The only legitimate _IOR is FW_CDEV_IOC_GET_CYCLE_TIMER with 12
or 16 bytes to memset.
[Another way to fix this would be strict checking of argument size (and
possibly direction) vs. command number. However, we then need a lookup
table, and we need to allow for slight size deviations in case of 32bit
userland on 64bit kernel.]
Reported-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The definition of struct fw_cdev_iso_packet seems to imply that the
header_length must be quadlet-aligned, and in fact, specifying an
unaligned header has never really worked when using multiple packet
structures, because the position of the next control word is computed by
rounding the header_length _down_, so the last one to three bytes of the
header would overlap the next control word.
To avoid this problem, check that the header length is properly aligned.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
In receive contexts, reject packets with header_length==0. This would
be an instruction to queue zero packets which would not make sense.
This prevents a division by zero in the OHCI driver.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The driver match strategy was:
- Match vendor/model/specifier/version of the unit directory.
- If that was a miss, match vendor from the root directory and
model/specifier/version of the unit directory.
This was inconsistent with how the modalias string was constructed
until recently (take vendor/model from root directory and specifier/
version from unit directory). It was also inconsistent with how it is
done since the parent commit:
- Use vendor/model/specifier/version of the unit directory if possible,
- fall back to one or more of vendor/model/specifier/version from the
root directory depending on which ones are not present at the unit
directory.
Fix this inconsistency by sharing the ROM scanner function between
modalias printer function and driver match function.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The modalias string of devices that represent units on a FireWire node
did not show Module_ID entries within unit directories. This was
because firewire-core searched only the root directory of the
configuration ROM for a Model_ID entry.
We now search first the root directory, then the unit directory. IOW
honor a unit directory's Model_ID if present, otherwise fall back to the
root directory's model ID (if present).
Furthermore, apply the same change to Vendor_ID. This had the same
issue but it was less apparent because most devices provide Vendor_ID
only in the root directory.
And finally, also use this strategy for the remaining two IDs in the
modalias, Specifier_ID and Version. It does not actually make sense to
look for them elsewhere than in the unit directory because they are
mandatory there. However, a uniform search order simplifies the
implementation and has no adverse affect in practice.
Side notes:
- The older counterpart of this, nodemgr.c of ieee1394, looked for
Vendor_ID first in the root directory, then in the unit directory,
and for Model_ID only in the unit directory.
- There is a single mainline driver which requires Vendor_ID and
Model_ID --- the firedtv driver. This one worked because FireDTVs
provide Vendor_ID in the root directory and Model_ID identically in
root directory and unit directory.
- Apart from firedtv, there are currently no drivers known to me
(including userspace drivers) that look at the Vendor_ID or Model_ID
of the modalias.
Reported-by: Maciej Żenczykowski <zenczykowski@gmail.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Among the many entries in the TSB12LV22 errata list (TI literature
number SLLS312) is the following:
PCI Slave reads of the Cycle Timer register may occasionally get an
incorrect value.
Software may be able to validate value by reading the register
multiple times rapidly and evaluating for a reasonable difference.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de> (untested)
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (added #define)
If the bandwidth allocation fails, the error must be returned in
*channel regardless of whether the channel allocation succeeded.
Checking for c >= 0 is not correct if no channel allocation was
requested, in which case this part of the code is reached with
c == -EINVAL.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
by the number of available isochronous DMA contexts and active quirks
which is occasionally useful information.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
This bug was present in firewire-ohci since day one: The number of
available isochronous receive DMA contexts was mixed up with that of
available isochronous transmit DMA contexts.
This is harmless on a few chips which offer the same number of contexts
in both directions, but most chips nowadays implement only the standard
minimum of 4 IR contexts, but 8 IT contexts. If a user attempted to run
a lot of IR contexts at once, results with more than four were therefore
unpredictable. I suppose the controller would simply refuse to start
DMA of any unimplemented context.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
This way, we can advise users of precompiled kernel packages to test
existing quirk fixes on chips which have not been listed yet, without
them having to build a kernel from source.
Note, to use this feature on a machine with more than one controller,
steps like these are necessary:
# lspci | grep 1394
# ls /sys/bus/pci/drivers/firewire_ohci/
# echo -n "0000:03:02.0" > /sys/bus/pci/drivers/firewire_ohci/unbind
# echo 2 > /sys/module/firewire_ohci/parameters/quirks
# echo -n "0000:03:02.0" > /sys/bus/pci/drivers/firewire_ohci/bind
# echo 0 > /sys/module/firewire_ohci/parameters/quirks
The parameter can also be used to switch off quirk flags that were
hardwired into firewire-ohci's quirks table. Simply specify a non-zero
quirks value but without any known flags, e.g. 0x100.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
We don't have a lot of quirks to take into account (especially since
dual-buffer IR is out of the picture), but still, a table-based approach
is more organized than a series of if () clauses.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The config_rom struct members are only accessed during relatively
infrequent self-ID-complete interrupts and only if the local config ROM
was changed, while the ar_, at_, ir_, it_ members are used very
frequently during I/O. Hence move the config_rom members further down.
More importantly, make the huge self_id_buffer member the last one; this
is only accessed in self-ID-complete interrupts.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
This code was no longer used since 2.6.33, "firewire: ohci: always use
packet-per-buffer mode for isochronous reception" commit 090699c0. If
anybody needs this code in the future for special purposes, it can be
brought back in. But it must not be re-enabled by default; drivers
(kernelspace or userspace drivers) should only get this mode if they
explicitly request it.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
