2005-04-16 16:20:36 -06:00
|
|
|
/*
|
|
|
|
* Linux Socket Filter - Kernel level socket filtering
|
|
|
|
*
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
* Based on the design of the Berkeley Packet Filter. The new
|
|
|
|
* internal format has been designed by PLUMgrid:
|
2005-04-16 16:20:36 -06:00
|
|
|
*
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
* Copyright (c) 2011 - 2014 PLUMgrid, http://plumgrid.com
|
|
|
|
*
|
|
|
|
* Authors:
|
|
|
|
*
|
|
|
|
* Jay Schulist <jschlst@samba.org>
|
|
|
|
* Alexei Starovoitov <ast@plumgrid.com>
|
|
|
|
* Daniel Borkmann <dborkman@redhat.com>
|
2005-04-16 16:20:36 -06:00
|
|
|
*
|
|
|
|
* This program is free software; you can redistribute it and/or
|
|
|
|
* modify it under the terms of the GNU General Public License
|
|
|
|
* as published by the Free Software Foundation; either version
|
|
|
|
* 2 of the License, or (at your option) any later version.
|
|
|
|
*
|
|
|
|
* Andi Kleen - Fix a few bad bugs and races.
|
2014-07-30 21:34:14 -06:00
|
|
|
* Kris Katterjohn - Added many additional checks in bpf_check_classic()
|
2005-04-16 16:20:36 -06:00
|
|
|
*/
|
|
|
|
|
|
|
|
#include <linux/module.h>
|
|
|
|
#include <linux/types.h>
|
|
|
|
#include <linux/mm.h>
|
|
|
|
#include <linux/fcntl.h>
|
|
|
|
#include <linux/socket.h>
|
|
|
|
#include <linux/in.h>
|
|
|
|
#include <linux/inet.h>
|
|
|
|
#include <linux/netdevice.h>
|
|
|
|
#include <linux/if_packet.h>
|
include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
2010-03-24 02:04:11 -06:00
|
|
|
#include <linux/gfp.h>
|
2005-04-16 16:20:36 -06:00
|
|
|
#include <net/ip.h>
|
|
|
|
#include <net/protocol.h>
|
[SKFILTER]: Add SKF_ADF_NLATTR instruction
SKF_ADF_NLATTR searches for a netlink attribute, which avoids manually
parsing and walking attributes. It takes the offset at which to start
searching in the 'A' register and the attribute type in the 'X' register
and returns the offset in the 'A' register. When the attribute is not
found it returns zero.
A top-level attribute can be located using a filter like this
(example for nfnetlink, using struct nfgenmsg):
...
{
/* A = offset of first attribute */
.code = BPF_LD | BPF_IMM,
.k = sizeof(struct nlmsghdr) + sizeof(struct nfgenmsg)
},
{
/* X = CTA_PROTOINFO */
.code = BPF_LDX | BPF_IMM,
.k = CTA_PROTOINFO,
},
{
/* A = netlink attribute offset */
.code = BPF_LD | BPF_B | BPF_ABS,
.k = SKF_AD_OFF + SKF_AD_NLATTR
},
{
/* Exit if not found */
.code = BPF_JMP | BPF_JEQ | BPF_K,
.k = 0,
.jt = <error>
},
...
A nested attribute below the CTA_PROTOINFO attribute would then
be parsed like this:
...
{
/* A += sizeof(struct nlattr) */
.code = BPF_ALU | BPF_ADD | BPF_K,
.k = sizeof(struct nlattr),
},
{
/* X = CTA_PROTOINFO_TCP */
.code = BPF_LDX | BPF_IMM,
.k = CTA_PROTOINFO_TCP,
},
{
/* A = netlink attribute offset */
.code = BPF_LD | BPF_B | BPF_ABS,
.k = SKF_AD_OFF + SKF_AD_NLATTR
},
...
The data of an attribute can be loaded into 'A' like this:
...
{
/* X = A (attribute offset) */
.code = BPF_MISC | BPF_TAX,
},
{
/* A = skb->data[X + k] */
.code = BPF_LD | BPF_B | BPF_IND,
.k = sizeof(struct nlattr),
},
...
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-04-10 03:02:28 -06:00
|
|
|
#include <net/netlink.h>
|
2005-04-16 16:20:36 -06:00
|
|
|
#include <linux/skbuff.h>
|
|
|
|
#include <net/sock.h>
|
2015-05-12 06:56:09 -06:00
|
|
|
#include <net/flow_dissector.h>
|
2005-04-16 16:20:36 -06:00
|
|
|
#include <linux/errno.h>
|
|
|
|
#include <linux/timer.h>
|
|
|
|
#include <asm/uaccess.h>
|
2006-04-18 15:50:10 -06:00
|
|
|
#include <asm/unaligned.h>
|
2005-04-16 16:20:36 -06:00
|
|
|
#include <linux/filter.h>
|
2011-05-26 13:00:31 -06:00
|
|
|
#include <linux/ratelimit.h>
|
2012-04-12 15:47:52 -06:00
|
|
|
#include <linux/seccomp.h>
|
2012-10-26 20:26:17 -06:00
|
|
|
#include <linux/if_vlan.h>
|
2014-12-01 16:06:35 -07:00
|
|
|
#include <linux/bpf.h>
|
2015-06-04 11:11:54 -06:00
|
|
|
#include <net/sch_generic.h>
|
2015-07-15 06:21:42 -06:00
|
|
|
#include <net/cls_cgroup.h>
|
bpf: add helpers to access tunnel metadata
Introduce helpers to let eBPF programs attached to TC manipulate tunnel metadata:
bpf_skb_[gs]et_tunnel_key(skb, key, size, flags)
skb: pointer to skb
key: pointer to 'struct bpf_tunnel_key'
size: size of 'struct bpf_tunnel_key'
flags: room for future extensions
First eBPF program that uses these helpers will allocate per_cpu
metadata_dst structures that will be used on TX.
On RX metadata_dst is allocated by tunnel driver.
Typical usage for TX:
struct bpf_tunnel_key tkey;
... populate tkey ...
bpf_skb_set_tunnel_key(skb, &tkey, sizeof(tkey), 0);
bpf_clone_redirect(skb, vxlan_dev_ifindex, 0);
RX:
struct bpf_tunnel_key tkey = {};
bpf_skb_get_tunnel_key(skb, &tkey, sizeof(tkey), 0);
... lookup or redirect based on tkey ...
'struct bpf_tunnel_key' will be extended in the future by adding
elements to the end and the 'size' argument will indicate which fields
are populated, thereby keeping backwards compatibility.
The 'flags' argument may be used as well when the 'size' is not enough or
to indicate completely different layout of bpf_tunnel_key.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-30 16:36:57 -06:00
|
|
|
#include <net/dst_metadata.h>
|
2015-09-29 17:41:51 -06:00
|
|
|
#include <net/dst.h>
|
2016-01-04 15:41:47 -07:00
|
|
|
#include <net/sock_reuseport.h>
|
2005-04-16 16:20:36 -06:00
|
|
|
|
2008-04-10 02:43:09 -06:00
|
|
|
/**
|
|
|
|
* sk_filter - run a packet through a socket filter
|
|
|
|
* @sk: sock associated with &sk_buff
|
|
|
|
* @skb: buffer to filter
|
|
|
|
*
|
2015-10-07 11:55:41 -06:00
|
|
|
* Run the eBPF program and then cut skb->data to correct size returned by
|
|
|
|
* the program. If pkt_len is 0 we toss packet. If skb->len is smaller
|
2008-04-10 02:43:09 -06:00
|
|
|
* than pkt_len we keep whole skb->data. This is the socket level
|
2015-10-07 11:55:41 -06:00
|
|
|
* wrapper to BPF_PROG_RUN. It returns 0 if the packet should
|
2008-04-10 02:43:09 -06:00
|
|
|
* be accepted or -EPERM if the packet should be tossed.
|
|
|
|
*
|
|
|
|
*/
|
|
|
|
int sk_filter(struct sock *sk, struct sk_buff *skb)
|
|
|
|
{
|
|
|
|
int err;
|
|
|
|
struct sk_filter *filter;
|
|
|
|
|
2012-07-31 17:44:19 -06:00
|
|
|
/*
|
|
|
|
* If the skb was allocated from pfmemalloc reserves, only
|
|
|
|
* allow SOCK_MEMALLOC sockets to use it as this socket is
|
|
|
|
* helping free memory
|
|
|
|
*/
|
|
|
|
if (skb_pfmemalloc(skb) && !sock_flag(sk, SOCK_MEMALLOC))
|
|
|
|
return -ENOMEM;
|
|
|
|
|
2008-04-10 02:43:09 -06:00
|
|
|
err = security_sock_rcv_skb(sk, skb);
|
|
|
|
if (err)
|
|
|
|
return err;
|
|
|
|
|
2011-01-18 00:46:52 -07:00
|
|
|
rcu_read_lock();
|
|
|
|
filter = rcu_dereference(sk->sk_filter);
|
2008-04-10 02:43:09 -06:00
|
|
|
if (filter) {
|
2015-10-07 11:55:41 -06:00
|
|
|
unsigned int pkt_len = bpf_prog_run_save_cb(filter->prog, skb);
|
2010-10-24 21:47:05 -06:00
|
|
|
|
2008-04-10 02:43:09 -06:00
|
|
|
err = pkt_len ? pskb_trim(skb, pkt_len) : -EPERM;
|
|
|
|
}
|
2011-01-18 00:46:52 -07:00
|
|
|
rcu_read_unlock();
|
2008-04-10 02:43:09 -06:00
|
|
|
|
|
|
|
return err;
|
|
|
|
}
|
|
|
|
EXPORT_SYMBOL(sk_filter);
|
|
|
|
|
2014-05-01 10:34:19 -06:00
|
|
|
static u64 __skb_get_pay_offset(u64 ctx, u64 a, u64 x, u64 r4, u64 r5)
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
{
|
2014-09-05 17:20:26 -06:00
|
|
|
return skb_get_poff((struct sk_buff *)(unsigned long) ctx);
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
}
|
|
|
|
|
2014-05-01 10:34:19 -06:00
|
|
|
static u64 __skb_get_nlattr(u64 ctx, u64 a, u64 x, u64 r4, u64 r5)
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
{
|
2014-05-01 10:34:20 -06:00
|
|
|
struct sk_buff *skb = (struct sk_buff *)(unsigned long) ctx;
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
struct nlattr *nla;
|
|
|
|
|
|
|
|
if (skb_is_nonlinear(skb))
|
|
|
|
return 0;
|
|
|
|
|
2014-04-13 10:23:33 -06:00
|
|
|
if (skb->len < sizeof(struct nlattr))
|
|
|
|
return 0;
|
|
|
|
|
2014-05-01 10:34:19 -06:00
|
|
|
if (a > skb->len - sizeof(struct nlattr))
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
return 0;
|
|
|
|
|
2014-05-01 10:34:19 -06:00
|
|
|
nla = nla_find((struct nlattr *) &skb->data[a], skb->len - a, x);
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
if (nla)
|
|
|
|
return (void *) nla - (void *) skb->data;
|
|
|
|
|
|
|
|
return 0;
|
|
|
|
}
|
|
|
|
|
2014-05-01 10:34:19 -06:00
|
|
|
static u64 __skb_get_nlattr_nest(u64 ctx, u64 a, u64 x, u64 r4, u64 r5)
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
{
|
2014-05-01 10:34:20 -06:00
|
|
|
struct sk_buff *skb = (struct sk_buff *)(unsigned long) ctx;
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
struct nlattr *nla;
|
|
|
|
|
|
|
|
if (skb_is_nonlinear(skb))
|
|
|
|
return 0;
|
|
|
|
|
2014-04-13 10:23:33 -06:00
|
|
|
if (skb->len < sizeof(struct nlattr))
|
|
|
|
return 0;
|
|
|
|
|
2014-05-01 10:34:19 -06:00
|
|
|
if (a > skb->len - sizeof(struct nlattr))
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
return 0;
|
|
|
|
|
2014-05-01 10:34:19 -06:00
|
|
|
nla = (struct nlattr *) &skb->data[a];
|
|
|
|
if (nla->nla_len > skb->len - a)
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
return 0;
|
|
|
|
|
2014-05-01 10:34:19 -06:00
|
|
|
nla = nla_find_nested(nla, x);
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
if (nla)
|
|
|
|
return (void *) nla - (void *) skb->data;
|
|
|
|
|
|
|
|
return 0;
|
|
|
|
}
|
|
|
|
|
2014-05-01 10:34:19 -06:00
|
|
|
static u64 __get_raw_cpu_id(u64 ctx, u64 a, u64 x, u64 r4, u64 r5)
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
{
|
|
|
|
return raw_smp_processor_id();
|
|
|
|
}
|
|
|
|
|
2015-03-13 12:57:42 -06:00
|
|
|
static u32 convert_skb_access(int skb_field, int dst_reg, int src_reg,
|
|
|
|
struct bpf_insn *insn_buf)
|
|
|
|
{
|
|
|
|
struct bpf_insn *insn = insn_buf;
|
|
|
|
|
|
|
|
switch (skb_field) {
|
|
|
|
case SKF_AD_MARK:
|
|
|
|
BUILD_BUG_ON(FIELD_SIZEOF(struct sk_buff, mark) != 4);
|
|
|
|
|
|
|
|
*insn++ = BPF_LDX_MEM(BPF_W, dst_reg, src_reg,
|
|
|
|
offsetof(struct sk_buff, mark));
|
|
|
|
break;
|
|
|
|
|
|
|
|
case SKF_AD_PKTTYPE:
|
|
|
|
*insn++ = BPF_LDX_MEM(BPF_B, dst_reg, src_reg, PKT_TYPE_OFFSET());
|
|
|
|
*insn++ = BPF_ALU32_IMM(BPF_AND, dst_reg, PKT_TYPE_MAX);
|
|
|
|
#ifdef __BIG_ENDIAN_BITFIELD
|
|
|
|
*insn++ = BPF_ALU32_IMM(BPF_RSH, dst_reg, 5);
|
|
|
|
#endif
|
|
|
|
break;
|
|
|
|
|
|
|
|
case SKF_AD_QUEUE:
|
|
|
|
BUILD_BUG_ON(FIELD_SIZEOF(struct sk_buff, queue_mapping) != 2);
|
|
|
|
|
|
|
|
*insn++ = BPF_LDX_MEM(BPF_H, dst_reg, src_reg,
|
|
|
|
offsetof(struct sk_buff, queue_mapping));
|
|
|
|
break;
|
2015-03-16 19:06:02 -06:00
|
|
|
|
|
|
|
case SKF_AD_VLAN_TAG:
|
|
|
|
case SKF_AD_VLAN_TAG_PRESENT:
|
|
|
|
BUILD_BUG_ON(FIELD_SIZEOF(struct sk_buff, vlan_tci) != 2);
|
|
|
|
BUILD_BUG_ON(VLAN_TAG_PRESENT != 0x1000);
|
|
|
|
|
|
|
|
/* dst_reg = *(u16 *) (src_reg + offsetof(vlan_tci)) */
|
|
|
|
*insn++ = BPF_LDX_MEM(BPF_H, dst_reg, src_reg,
|
|
|
|
offsetof(struct sk_buff, vlan_tci));
|
|
|
|
if (skb_field == SKF_AD_VLAN_TAG) {
|
|
|
|
*insn++ = BPF_ALU32_IMM(BPF_AND, dst_reg,
|
|
|
|
~VLAN_TAG_PRESENT);
|
|
|
|
} else {
|
|
|
|
/* dst_reg >>= 12 */
|
|
|
|
*insn++ = BPF_ALU32_IMM(BPF_RSH, dst_reg, 12);
|
|
|
|
/* dst_reg &= 1 */
|
|
|
|
*insn++ = BPF_ALU32_IMM(BPF_AND, dst_reg, 1);
|
|
|
|
}
|
|
|
|
break;
|
2015-03-13 12:57:42 -06:00
|
|
|
}
|
|
|
|
|
|
|
|
return insn - insn_buf;
|
|
|
|
}
|
|
|
|
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
static bool convert_bpf_extensions(struct sock_filter *fp,
|
2014-07-24 17:38:21 -06:00
|
|
|
struct bpf_insn **insnp)
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
{
|
2014-07-24 17:38:21 -06:00
|
|
|
struct bpf_insn *insn = *insnp;
|
2015-03-13 12:57:42 -06:00
|
|
|
u32 cnt;
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
|
|
|
|
switch (fp->k) {
|
|
|
|
case SKF_AD_OFF + SKF_AD_PROTOCOL:
|
2015-03-19 12:38:27 -06:00
|
|
|
BUILD_BUG_ON(FIELD_SIZEOF(struct sk_buff, protocol) != 2);
|
|
|
|
|
|
|
|
/* A = *(u16 *) (CTX + offsetof(protocol)) */
|
|
|
|
*insn++ = BPF_LDX_MEM(BPF_H, BPF_REG_A, BPF_REG_CTX,
|
|
|
|
offsetof(struct sk_buff, protocol));
|
|
|
|
/* A = ntohs(A) [emitting a nop or swap16] */
|
|
|
|
*insn = BPF_ENDIAN(BPF_FROM_BE, BPF_REG_A, 16);
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
break;
|
|
|
|
|
|
|
|
case SKF_AD_OFF + SKF_AD_PKTTYPE:
|
2015-03-13 12:57:42 -06:00
|
|
|
cnt = convert_skb_access(SKF_AD_PKTTYPE, BPF_REG_A, BPF_REG_CTX, insn);
|
|
|
|
insn += cnt - 1;
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
break;
|
|
|
|
|
|
|
|
case SKF_AD_OFF + SKF_AD_IFINDEX:
|
|
|
|
case SKF_AD_OFF + SKF_AD_HATYPE:
|
|
|
|
BUILD_BUG_ON(FIELD_SIZEOF(struct net_device, ifindex) != 4);
|
|
|
|
BUILD_BUG_ON(FIELD_SIZEOF(struct net_device, type) != 2);
|
2014-05-29 02:22:51 -06:00
|
|
|
BUILD_BUG_ON(bytes_to_bpf_size(FIELD_SIZEOF(struct sk_buff, dev)) < 0);
|
|
|
|
|
|
|
|
*insn++ = BPF_LDX_MEM(bytes_to_bpf_size(FIELD_SIZEOF(struct sk_buff, dev)),
|
|
|
|
BPF_REG_TMP, BPF_REG_CTX,
|
|
|
|
offsetof(struct sk_buff, dev));
|
|
|
|
/* if (tmp != 0) goto pc + 1 */
|
|
|
|
*insn++ = BPF_JMP_IMM(BPF_JNE, BPF_REG_TMP, 0, 1);
|
|
|
|
*insn++ = BPF_EXIT_INSN();
|
|
|
|
if (fp->k == SKF_AD_OFF + SKF_AD_IFINDEX)
|
|
|
|
*insn = BPF_LDX_MEM(BPF_W, BPF_REG_A, BPF_REG_TMP,
|
|
|
|
offsetof(struct net_device, ifindex));
|
|
|
|
else
|
|
|
|
*insn = BPF_LDX_MEM(BPF_H, BPF_REG_A, BPF_REG_TMP,
|
|
|
|
offsetof(struct net_device, type));
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
break;
|
|
|
|
|
|
|
|
case SKF_AD_OFF + SKF_AD_MARK:
|
2015-03-13 12:57:42 -06:00
|
|
|
cnt = convert_skb_access(SKF_AD_MARK, BPF_REG_A, BPF_REG_CTX, insn);
|
|
|
|
insn += cnt - 1;
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
break;
|
|
|
|
|
|
|
|
case SKF_AD_OFF + SKF_AD_RXHASH:
|
|
|
|
BUILD_BUG_ON(FIELD_SIZEOF(struct sk_buff, hash) != 4);
|
|
|
|
|
2014-05-08 15:10:51 -06:00
|
|
|
*insn = BPF_LDX_MEM(BPF_W, BPF_REG_A, BPF_REG_CTX,
|
|
|
|
offsetof(struct sk_buff, hash));
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
break;
|
|
|
|
|
|
|
|
case SKF_AD_OFF + SKF_AD_QUEUE:
|
2015-03-13 12:57:42 -06:00
|
|
|
cnt = convert_skb_access(SKF_AD_QUEUE, BPF_REG_A, BPF_REG_CTX, insn);
|
|
|
|
insn += cnt - 1;
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
break;
|
|
|
|
|
|
|
|
case SKF_AD_OFF + SKF_AD_VLAN_TAG:
|
2015-03-16 19:06:02 -06:00
|
|
|
cnt = convert_skb_access(SKF_AD_VLAN_TAG,
|
|
|
|
BPF_REG_A, BPF_REG_CTX, insn);
|
|
|
|
insn += cnt - 1;
|
|
|
|
break;
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
|
2015-03-16 19:06:02 -06:00
|
|
|
case SKF_AD_OFF + SKF_AD_VLAN_TAG_PRESENT:
|
|
|
|
cnt = convert_skb_access(SKF_AD_VLAN_TAG_PRESENT,
|
|
|
|
BPF_REG_A, BPF_REG_CTX, insn);
|
|
|
|
insn += cnt - 1;
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
break;
|
|
|
|
|
2015-03-24 07:48:41 -06:00
|
|
|
case SKF_AD_OFF + SKF_AD_VLAN_TPID:
|
|
|
|
BUILD_BUG_ON(FIELD_SIZEOF(struct sk_buff, vlan_proto) != 2);
|
|
|
|
|
|
|
|
/* A = *(u16 *) (CTX + offsetof(vlan_proto)) */
|
|
|
|
*insn++ = BPF_LDX_MEM(BPF_H, BPF_REG_A, BPF_REG_CTX,
|
|
|
|
offsetof(struct sk_buff, vlan_proto));
|
|
|
|
/* A = ntohs(A) [emitting a nop or swap16] */
|
|
|
|
*insn = BPF_ENDIAN(BPF_FROM_BE, BPF_REG_A, 16);
|
|
|
|
break;
|
|
|
|
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
case SKF_AD_OFF + SKF_AD_PAY_OFFSET:
|
|
|
|
case SKF_AD_OFF + SKF_AD_NLATTR:
|
|
|
|
case SKF_AD_OFF + SKF_AD_NLATTR_NEST:
|
|
|
|
case SKF_AD_OFF + SKF_AD_CPU:
|
2014-04-21 10:21:24 -06:00
|
|
|
case SKF_AD_OFF + SKF_AD_RANDOM:
|
2014-06-06 15:46:06 -06:00
|
|
|
/* arg1 = CTX */
|
2014-05-29 02:22:51 -06:00
|
|
|
*insn++ = BPF_MOV64_REG(BPF_REG_ARG1, BPF_REG_CTX);
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
/* arg2 = A */
|
2014-05-29 02:22:51 -06:00
|
|
|
*insn++ = BPF_MOV64_REG(BPF_REG_ARG2, BPF_REG_A);
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
/* arg3 = X */
|
2014-05-29 02:22:51 -06:00
|
|
|
*insn++ = BPF_MOV64_REG(BPF_REG_ARG3, BPF_REG_X);
|
2014-06-06 15:46:06 -06:00
|
|
|
/* Emit call(arg1=CTX, arg2=A, arg3=X) */
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
switch (fp->k) {
|
|
|
|
case SKF_AD_OFF + SKF_AD_PAY_OFFSET:
|
2014-05-29 02:22:51 -06:00
|
|
|
*insn = BPF_EMIT_CALL(__skb_get_pay_offset);
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
break;
|
|
|
|
case SKF_AD_OFF + SKF_AD_NLATTR:
|
2014-05-29 02:22:51 -06:00
|
|
|
*insn = BPF_EMIT_CALL(__skb_get_nlattr);
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
break;
|
|
|
|
case SKF_AD_OFF + SKF_AD_NLATTR_NEST:
|
2014-05-29 02:22:51 -06:00
|
|
|
*insn = BPF_EMIT_CALL(__skb_get_nlattr_nest);
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
break;
|
|
|
|
case SKF_AD_OFF + SKF_AD_CPU:
|
2014-05-29 02:22:51 -06:00
|
|
|
*insn = BPF_EMIT_CALL(__get_raw_cpu_id);
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
break;
|
2014-04-21 10:21:24 -06:00
|
|
|
case SKF_AD_OFF + SKF_AD_RANDOM:
|
bpf: split state from prandom_u32() and consolidate {c, e}BPF prngs
While recently arguing on a seccomp discussion that raw prandom_u32()
access shouldn't be exposed to unpriviledged user space, I forgot the
fact that SKF_AD_RANDOM extension actually already does it for some time
in cBPF via commit 4cd3675ebf74 ("filter: added BPF random opcode").
Since prandom_u32() is being used in a lot of critical networking code,
lets be more conservative and split their states. Furthermore, consolidate
eBPF and cBPF prandom handlers to use the new internal PRNG. For eBPF,
bpf_get_prandom_u32() was only accessible for priviledged users, but
should that change one day, we also don't want to leak raw sequences
through things like eBPF maps.
One thought was also to have own per bpf_prog states, but due to ABI
reasons this is not easily possible, i.e. the program code currently
cannot access bpf_prog itself, and copying the rnd_state to/from the
stack scratch space whenever a program uses the prng seems not really
worth the trouble and seems too hacky. If needed, taus113 could in such
cases be implemented within eBPF using a map entry to keep the state
space, or get_random_bytes() could become a second helper in cases where
performance would not be critical.
Both sides can trigger a one-time late init via prandom_init_once() on
the shared state. Performance-wise, there should even be a tiny gain
as bpf_user_rnd_u32() saves one function call. The PRNG needs to live
inside the BPF core since kernels could have a NET-less config as well.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Cc: Chema Gonzalez <chema@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-10-07 17:20:39 -06:00
|
|
|
*insn = BPF_EMIT_CALL(bpf_user_rnd_u32);
|
|
|
|
bpf_user_rnd_init_once();
|
2014-04-21 10:21:24 -06:00
|
|
|
break;
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
}
|
|
|
|
break;
|
|
|
|
|
|
|
|
case SKF_AD_OFF + SKF_AD_ALU_XOR_X:
|
2014-05-08 15:10:51 -06:00
|
|
|
/* A ^= X */
|
|
|
|
*insn = BPF_ALU32_REG(BPF_XOR, BPF_REG_A, BPF_REG_X);
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
break;
|
|
|
|
|
|
|
|
default:
|
|
|
|
/* This is just a dummy call to avoid letting the compiler
|
|
|
|
* evict __bpf_call_base() as an optimization. Placed here
|
|
|
|
* where no-one bothers.
|
|
|
|
*/
|
|
|
|
BUG_ON(__bpf_call_base(0, 0, 0, 0, 0) != 0);
|
|
|
|
return false;
|
|
|
|
}
|
|
|
|
|
|
|
|
*insnp = insn;
|
|
|
|
return true;
|
|
|
|
}
|
|
|
|
|
|
|
|
/**
|
2014-07-30 21:34:15 -06:00
|
|
|
* bpf_convert_filter - convert filter program
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
* @prog: the user passed filter program
|
|
|
|
* @len: the length of the user passed filter program
|
|
|
|
* @new_prog: buffer where converted program will be stored
|
|
|
|
* @new_len: pointer to store length of converted program
|
|
|
|
*
|
|
|
|
* Remap 'sock_filter' style BPF instruction set to 'sock_filter_ext' style.
|
|
|
|
* Conversion workflow:
|
|
|
|
*
|
|
|
|
* 1) First pass for calculating the new program length:
|
2014-07-30 21:34:15 -06:00
|
|
|
* bpf_convert_filter(old_prog, old_len, NULL, &new_len)
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
*
|
|
|
|
* 2) 2nd pass to remap in two passes: 1st pass finds new
|
|
|
|
* jump offsets, 2nd pass remapping:
|
2014-07-24 17:38:21 -06:00
|
|
|
* new_prog = kmalloc(sizeof(struct bpf_insn) * new_len);
|
2014-07-30 21:34:15 -06:00
|
|
|
* bpf_convert_filter(old_prog, old_len, new_prog, &new_len);
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
*/
|
2015-05-06 08:12:28 -06:00
|
|
|
static int bpf_convert_filter(struct sock_filter *prog, int len,
|
|
|
|
struct bpf_insn *new_prog, int *new_len)
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
{
|
|
|
|
int new_flen = 0, pass = 0, target, i;
|
2014-07-24 17:38:21 -06:00
|
|
|
struct bpf_insn *new_insn;
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
struct sock_filter *fp;
|
|
|
|
int *addrs = NULL;
|
|
|
|
u8 bpf_src;
|
|
|
|
|
|
|
|
BUILD_BUG_ON(BPF_MEMWORDS * sizeof(u32) > MAX_BPF_STACK);
|
2014-05-01 10:34:19 -06:00
|
|
|
BUILD_BUG_ON(BPF_REG_FP + 1 != MAX_BPF_REG);
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
|
2014-06-18 16:34:57 -06:00
|
|
|
if (len <= 0 || len > BPF_MAXINSNS)
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
return -EINVAL;
|
|
|
|
|
|
|
|
if (new_prog) {
|
2015-05-06 08:12:29 -06:00
|
|
|
addrs = kcalloc(len, sizeof(*addrs),
|
|
|
|
GFP_KERNEL | __GFP_NOWARN);
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
if (!addrs)
|
|
|
|
return -ENOMEM;
|
|
|
|
}
|
|
|
|
|
|
|
|
do_pass:
|
|
|
|
new_insn = new_prog;
|
|
|
|
fp = prog;
|
|
|
|
|
bpf: move clearing of A/X into classic to eBPF migration prologue
Back in the days where eBPF (or back then "internal BPF" ;->) was not
exposed to user space, and only the classic BPF programs internally
translated into eBPF programs, we missed the fact that for classic BPF
A and X needed to be cleared. It was fixed back then via 83d5b7ef99c9
("net: filter: initialize A and X registers"), and thus classic BPF
specifics were added to the eBPF interpreter core to work around it.
This added some confusion for JIT developers later on that take the
eBPF interpreter code as an example for deriving their JIT. F.e. in
f75298f5c3fe ("s390/bpf: clear correct BPF accumulator register"), at
least X could leak stack memory. Furthermore, since this is only needed
for classic BPF translations and not for eBPF (verifier takes care
that read access to regs cannot be done uninitialized), more complexity
is added to JITs as they need to determine whether they deal with
migrations or native eBPF where they can just omit clearing A/X in
their prologue and thus reduce image size a bit, see f.e. cde66c2d88da
("s390/bpf: Only clear A and X for converted BPF programs"). In other
cases (x86, arm64), A and X is being cleared in the prologue also for
eBPF case, which is unnecessary.
Lets move this into the BPF migration in bpf_convert_filter() where it
actually belongs as long as the number of eBPF JITs are still few. It
can thus be done generically; allowing us to remove the quirk from
__bpf_prog_run() and to slightly reduce JIT image size in case of eBPF,
while reducing code duplication on this matter in current(/future) eBPF
JITs.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Tested-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Cc: Zi Shen Lim <zlim.lnx@gmail.com>
Cc: Yang Shi <yang.shi@linaro.org>
Acked-by: Yang Shi <yang.shi@linaro.org>
Acked-by: Zi Shen Lim <zlim.lnx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-17 15:51:54 -07:00
|
|
|
/* Classic BPF related prologue emission. */
|
|
|
|
if (new_insn) {
|
|
|
|
/* Classic BPF expects A and X to be reset first. These need
|
|
|
|
* to be guaranteed to be the first two instructions.
|
|
|
|
*/
|
|
|
|
*new_insn++ = BPF_ALU64_REG(BPF_XOR, BPF_REG_A, BPF_REG_A);
|
|
|
|
*new_insn++ = BPF_ALU64_REG(BPF_XOR, BPF_REG_X, BPF_REG_X);
|
|
|
|
|
|
|
|
/* All programs must keep CTX in callee saved BPF_REG_CTX.
|
|
|
|
* In eBPF case it's done by the compiler, here we need to
|
|
|
|
* do this ourself. Initial CTX is present in BPF_REG_ARG1.
|
|
|
|
*/
|
|
|
|
*new_insn++ = BPF_MOV64_REG(BPF_REG_CTX, BPF_REG_ARG1);
|
|
|
|
} else {
|
|
|
|
new_insn += 3;
|
|
|
|
}
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
|
|
|
|
for (i = 0; i < len; fp++, i++) {
|
2014-07-24 17:38:21 -06:00
|
|
|
struct bpf_insn tmp_insns[6] = { };
|
|
|
|
struct bpf_insn *insn = tmp_insns;
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
|
|
|
|
if (addrs)
|
|
|
|
addrs[i] = new_insn - new_prog;
|
|
|
|
|
|
|
|
switch (fp->code) {
|
|
|
|
/* All arithmetic insns and skb loads map as-is. */
|
|
|
|
case BPF_ALU | BPF_ADD | BPF_X:
|
|
|
|
case BPF_ALU | BPF_ADD | BPF_K:
|
|
|
|
case BPF_ALU | BPF_SUB | BPF_X:
|
|
|
|
case BPF_ALU | BPF_SUB | BPF_K:
|
|
|
|
case BPF_ALU | BPF_AND | BPF_X:
|
|
|
|
case BPF_ALU | BPF_AND | BPF_K:
|
|
|
|
case BPF_ALU | BPF_OR | BPF_X:
|
|
|
|
case BPF_ALU | BPF_OR | BPF_K:
|
|
|
|
case BPF_ALU | BPF_LSH | BPF_X:
|
|
|
|
case BPF_ALU | BPF_LSH | BPF_K:
|
|
|
|
case BPF_ALU | BPF_RSH | BPF_X:
|
|
|
|
case BPF_ALU | BPF_RSH | BPF_K:
|
|
|
|
case BPF_ALU | BPF_XOR | BPF_X:
|
|
|
|
case BPF_ALU | BPF_XOR | BPF_K:
|
|
|
|
case BPF_ALU | BPF_MUL | BPF_X:
|
|
|
|
case BPF_ALU | BPF_MUL | BPF_K:
|
|
|
|
case BPF_ALU | BPF_DIV | BPF_X:
|
|
|
|
case BPF_ALU | BPF_DIV | BPF_K:
|
|
|
|
case BPF_ALU | BPF_MOD | BPF_X:
|
|
|
|
case BPF_ALU | BPF_MOD | BPF_K:
|
|
|
|
case BPF_ALU | BPF_NEG:
|
|
|
|
case BPF_LD | BPF_ABS | BPF_W:
|
|
|
|
case BPF_LD | BPF_ABS | BPF_H:
|
|
|
|
case BPF_LD | BPF_ABS | BPF_B:
|
|
|
|
case BPF_LD | BPF_IND | BPF_W:
|
|
|
|
case BPF_LD | BPF_IND | BPF_H:
|
|
|
|
case BPF_LD | BPF_IND | BPF_B:
|
|
|
|
/* Check for overloaded BPF extension and
|
|
|
|
* directly convert it if found, otherwise
|
|
|
|
* just move on with mapping.
|
|
|
|
*/
|
|
|
|
if (BPF_CLASS(fp->code) == BPF_LD &&
|
|
|
|
BPF_MODE(fp->code) == BPF_ABS &&
|
|
|
|
convert_bpf_extensions(fp, &insn))
|
|
|
|
break;
|
|
|
|
|
2014-05-29 02:22:51 -06:00
|
|
|
*insn = BPF_RAW_INSN(fp->code, BPF_REG_A, BPF_REG_X, 0, fp->k);
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
break;
|
|
|
|
|
2014-05-29 02:22:51 -06:00
|
|
|
/* Jump transformation cannot use BPF block macros
|
|
|
|
* everywhere as offset calculation and target updates
|
|
|
|
* require a bit more work than the rest, i.e. jump
|
|
|
|
* opcodes map as-is, but offsets need adjustment.
|
|
|
|
*/
|
|
|
|
|
|
|
|
#define BPF_EMIT_JMP \
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
do { \
|
|
|
|
if (target >= len || target < 0) \
|
|
|
|
goto err; \
|
|
|
|
insn->off = addrs ? addrs[target] - addrs[i] - 1 : 0; \
|
|
|
|
/* Adjust pc relative offset for 2nd or 3rd insn. */ \
|
|
|
|
insn->off -= insn - tmp_insns; \
|
|
|
|
} while (0)
|
|
|
|
|
2014-05-29 02:22:51 -06:00
|
|
|
case BPF_JMP | BPF_JA:
|
|
|
|
target = i + fp->k + 1;
|
|
|
|
insn->code = fp->code;
|
|
|
|
BPF_EMIT_JMP;
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
break;
|
|
|
|
|
|
|
|
case BPF_JMP | BPF_JEQ | BPF_K:
|
|
|
|
case BPF_JMP | BPF_JEQ | BPF_X:
|
|
|
|
case BPF_JMP | BPF_JSET | BPF_K:
|
|
|
|
case BPF_JMP | BPF_JSET | BPF_X:
|
|
|
|
case BPF_JMP | BPF_JGT | BPF_K:
|
|
|
|
case BPF_JMP | BPF_JGT | BPF_X:
|
|
|
|
case BPF_JMP | BPF_JGE | BPF_K:
|
|
|
|
case BPF_JMP | BPF_JGE | BPF_X:
|
|
|
|
if (BPF_SRC(fp->code) == BPF_K && (int) fp->k < 0) {
|
|
|
|
/* BPF immediates are signed, zero extend
|
|
|
|
* immediate into tmp register and use it
|
|
|
|
* in compare insn.
|
|
|
|
*/
|
2014-05-29 02:22:51 -06:00
|
|
|
*insn++ = BPF_MOV32_IMM(BPF_REG_TMP, fp->k);
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
|
2014-06-06 15:46:06 -06:00
|
|
|
insn->dst_reg = BPF_REG_A;
|
|
|
|
insn->src_reg = BPF_REG_TMP;
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
bpf_src = BPF_X;
|
|
|
|
} else {
|
2014-06-06 15:46:06 -06:00
|
|
|
insn->dst_reg = BPF_REG_A;
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
insn->imm = fp->k;
|
|
|
|
bpf_src = BPF_SRC(fp->code);
|
2015-09-10 18:25:07 -06:00
|
|
|
insn->src_reg = bpf_src == BPF_X ? BPF_REG_X : 0;
|
2005-04-16 16:20:36 -06:00
|
|
|
}
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
|
|
|
|
/* Common case where 'jump_false' is next insn. */
|
|
|
|
if (fp->jf == 0) {
|
|
|
|
insn->code = BPF_JMP | BPF_OP(fp->code) | bpf_src;
|
|
|
|
target = i + fp->jt + 1;
|
2014-05-29 02:22:51 -06:00
|
|
|
BPF_EMIT_JMP;
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
break;
|
2005-04-16 16:20:36 -06:00
|
|
|
}
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
|
|
|
|
/* Convert JEQ into JNE when 'jump_true' is next insn. */
|
|
|
|
if (fp->jt == 0 && BPF_OP(fp->code) == BPF_JEQ) {
|
|
|
|
insn->code = BPF_JMP | BPF_JNE | bpf_src;
|
|
|
|
target = i + fp->jf + 1;
|
2014-05-29 02:22:51 -06:00
|
|
|
BPF_EMIT_JMP;
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
break;
|
2005-07-05 15:10:21 -06:00
|
|
|
}
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
|
|
|
|
/* Other jumps are mapped into two insns: Jxx and JA. */
|
|
|
|
target = i + fp->jt + 1;
|
|
|
|
insn->code = BPF_JMP | BPF_OP(fp->code) | bpf_src;
|
2014-05-29 02:22:51 -06:00
|
|
|
BPF_EMIT_JMP;
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
insn++;
|
|
|
|
|
|
|
|
insn->code = BPF_JMP | BPF_JA;
|
|
|
|
target = i + fp->jf + 1;
|
2014-05-29 02:22:51 -06:00
|
|
|
BPF_EMIT_JMP;
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
break;
|
|
|
|
|
|
|
|
/* ldxb 4 * ([14] & 0xf) is remaped into 6 insns. */
|
|
|
|
case BPF_LDX | BPF_MSH | BPF_B:
|
2014-05-08 15:10:51 -06:00
|
|
|
/* tmp = A */
|
2014-05-29 02:22:51 -06:00
|
|
|
*insn++ = BPF_MOV64_REG(BPF_REG_TMP, BPF_REG_A);
|
2014-05-13 11:13:33 -06:00
|
|
|
/* A = BPF_R0 = *(u8 *) (skb->data + K) */
|
2014-05-29 02:22:51 -06:00
|
|
|
*insn++ = BPF_LD_ABS(BPF_B, fp->k);
|
2014-05-08 15:10:51 -06:00
|
|
|
/* A &= 0xf */
|
2014-05-29 02:22:51 -06:00
|
|
|
*insn++ = BPF_ALU32_IMM(BPF_AND, BPF_REG_A, 0xf);
|
2014-05-08 15:10:51 -06:00
|
|
|
/* A <<= 2 */
|
2014-05-29 02:22:51 -06:00
|
|
|
*insn++ = BPF_ALU32_IMM(BPF_LSH, BPF_REG_A, 2);
|
2014-05-08 15:10:51 -06:00
|
|
|
/* X = A */
|
2014-05-29 02:22:51 -06:00
|
|
|
*insn++ = BPF_MOV64_REG(BPF_REG_X, BPF_REG_A);
|
2014-05-08 15:10:51 -06:00
|
|
|
/* A = tmp */
|
2014-05-29 02:22:51 -06:00
|
|
|
*insn = BPF_MOV64_REG(BPF_REG_A, BPF_REG_TMP);
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
break;
|
|
|
|
|
2016-02-19 15:05:27 -07:00
|
|
|
/* RET_K is remaped into 2 insns. RET_A case doesn't need an
|
|
|
|
* extra mov as BPF_REG_0 is already mapped into BPF_REG_A.
|
|
|
|
*/
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
case BPF_RET | BPF_A:
|
|
|
|
case BPF_RET | BPF_K:
|
2016-02-19 15:05:27 -07:00
|
|
|
if (BPF_RVAL(fp->code) == BPF_K)
|
|
|
|
*insn++ = BPF_MOV32_RAW(BPF_K, BPF_REG_0,
|
|
|
|
0, fp->k);
|
2014-05-08 15:10:51 -06:00
|
|
|
*insn = BPF_EXIT_INSN();
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
break;
|
|
|
|
|
|
|
|
/* Store to stack. */
|
|
|
|
case BPF_ST:
|
|
|
|
case BPF_STX:
|
2014-05-29 02:22:51 -06:00
|
|
|
*insn = BPF_STX_MEM(BPF_W, BPF_REG_FP, BPF_CLASS(fp->code) ==
|
|
|
|
BPF_ST ? BPF_REG_A : BPF_REG_X,
|
|
|
|
-(BPF_MEMWORDS - fp->k) * 4);
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
break;
|
|
|
|
|
|
|
|
/* Load from stack. */
|
|
|
|
case BPF_LD | BPF_MEM:
|
|
|
|
case BPF_LDX | BPF_MEM:
|
2014-05-29 02:22:51 -06:00
|
|
|
*insn = BPF_LDX_MEM(BPF_W, BPF_CLASS(fp->code) == BPF_LD ?
|
|
|
|
BPF_REG_A : BPF_REG_X, BPF_REG_FP,
|
|
|
|
-(BPF_MEMWORDS - fp->k) * 4);
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
break;
|
|
|
|
|
|
|
|
/* A = K or X = K */
|
|
|
|
case BPF_LD | BPF_IMM:
|
|
|
|
case BPF_LDX | BPF_IMM:
|
2014-05-29 02:22:51 -06:00
|
|
|
*insn = BPF_MOV32_IMM(BPF_CLASS(fp->code) == BPF_LD ?
|
|
|
|
BPF_REG_A : BPF_REG_X, fp->k);
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
break;
|
|
|
|
|
|
|
|
/* X = A */
|
|
|
|
case BPF_MISC | BPF_TAX:
|
2014-05-29 02:22:51 -06:00
|
|
|
*insn = BPF_MOV64_REG(BPF_REG_X, BPF_REG_A);
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
break;
|
|
|
|
|
|
|
|
/* A = X */
|
|
|
|
case BPF_MISC | BPF_TXA:
|
2014-05-29 02:22:51 -06:00
|
|
|
*insn = BPF_MOV64_REG(BPF_REG_A, BPF_REG_X);
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
break;
|
|
|
|
|
|
|
|
/* A = skb->len or X = skb->len */
|
|
|
|
case BPF_LD | BPF_W | BPF_LEN:
|
|
|
|
case BPF_LDX | BPF_W | BPF_LEN:
|
2014-05-29 02:22:51 -06:00
|
|
|
*insn = BPF_LDX_MEM(BPF_W, BPF_CLASS(fp->code) == BPF_LD ?
|
|
|
|
BPF_REG_A : BPF_REG_X, BPF_REG_CTX,
|
|
|
|
offsetof(struct sk_buff, len));
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
break;
|
|
|
|
|
2014-05-29 02:22:51 -06:00
|
|
|
/* Access seccomp_data fields. */
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
case BPF_LDX | BPF_ABS | BPF_W:
|
2014-05-08 15:10:51 -06:00
|
|
|
/* A = *(u32 *) (ctx + K) */
|
|
|
|
*insn = BPF_LDX_MEM(BPF_W, BPF_REG_A, BPF_REG_CTX, fp->k);
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
break;
|
|
|
|
|
2015-02-14 11:47:54 -07:00
|
|
|
/* Unknown instruction. */
|
2005-04-16 16:20:36 -06:00
|
|
|
default:
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
goto err;
|
2005-04-16 16:20:36 -06:00
|
|
|
}
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
|
|
|
|
insn++;
|
|
|
|
if (new_prog)
|
|
|
|
memcpy(new_insn, tmp_insns,
|
|
|
|
sizeof(*insn) * (insn - tmp_insns));
|
|
|
|
new_insn += insn - tmp_insns;
|
2005-04-16 16:20:36 -06:00
|
|
|
}
|
|
|
|
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
if (!new_prog) {
|
|
|
|
/* Only calculating new length. */
|
|
|
|
*new_len = new_insn - new_prog;
|
|
|
|
return 0;
|
|
|
|
}
|
|
|
|
|
|
|
|
pass++;
|
|
|
|
if (new_flen != new_insn - new_prog) {
|
|
|
|
new_flen = new_insn - new_prog;
|
|
|
|
if (pass > 2)
|
|
|
|
goto err;
|
|
|
|
goto do_pass;
|
|
|
|
}
|
|
|
|
|
|
|
|
kfree(addrs);
|
|
|
|
BUG_ON(*new_len != new_flen);
|
2005-04-16 16:20:36 -06:00
|
|
|
return 0;
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
err:
|
|
|
|
kfree(addrs);
|
|
|
|
return -EINVAL;
|
2005-04-16 16:20:36 -06:00
|
|
|
}
|
|
|
|
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
/* Security:
|
|
|
|
*
|
2010-12-01 13:46:24 -07:00
|
|
|
* As we dont want to clear mem[] array for each packet going through
|
2014-10-09 23:56:51 -06:00
|
|
|
* __bpf_prog_run(), we check that filter loaded by user never try to read
|
2010-12-01 13:46:24 -07:00
|
|
|
* a cell if not previously written, and we check all branches to be sure
|
2011-03-30 19:57:33 -06:00
|
|
|
* a malicious user doesn't try to abuse us.
|
2010-12-01 13:46:24 -07:00
|
|
|
*/
|
2014-07-12 07:49:16 -06:00
|
|
|
static int check_load_and_stores(const struct sock_filter *filter, int flen)
|
2010-12-01 13:46:24 -07:00
|
|
|
{
|
net: filter: get rid of BPF_S_* enum
This patch finally allows us to get rid of the BPF_S_* enum.
Currently, the code performs unnecessary encode and decode
workarounds in seccomp and filter migration itself when a filter
is being attached in order to overcome BPF_S_* encoding which
is not used anymore by the new interpreter resp. JIT compilers.
Keeping it around would mean that also in future we would need
to extend and maintain this enum and related encoders/decoders.
We can get rid of all that and save us these operations during
filter attaching. Naturally, also JIT compilers need to be updated
by this.
Before JIT conversion is being done, each compiler checks if A
is being loaded at startup to obtain information if it needs to
emit instructions to clear A first. Since BPF extensions are a
subset of BPF_LD | BPF_{W,H,B} | BPF_ABS variants, case statements
for extensions can be removed at that point. To ease and minimalize
code changes in the classic JITs, we have introduced bpf_anc_helper().
Tested with test_bpf on x86_64 (JIT, int), s390x (JIT, int),
arm (JIT, int), i368 (int), ppc64 (JIT, int); for sparc we
unfortunately didn't have access, but changes are analogous to
the rest.
Joint work with Alexei Starovoitov.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Mircea Gherzan <mgherzan@gmail.com>
Cc: Kees Cook <keescook@chromium.org>
Acked-by: Chema Gonzalez <chemag@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-29 02:22:50 -06:00
|
|
|
u16 *masks, memvalid = 0; /* One bit per cell, 16 cells */
|
2010-12-01 13:46:24 -07:00
|
|
|
int pc, ret = 0;
|
|
|
|
|
|
|
|
BUILD_BUG_ON(BPF_MEMWORDS > 16);
|
net: filter: get rid of BPF_S_* enum
This patch finally allows us to get rid of the BPF_S_* enum.
Currently, the code performs unnecessary encode and decode
workarounds in seccomp and filter migration itself when a filter
is being attached in order to overcome BPF_S_* encoding which
is not used anymore by the new interpreter resp. JIT compilers.
Keeping it around would mean that also in future we would need
to extend and maintain this enum and related encoders/decoders.
We can get rid of all that and save us these operations during
filter attaching. Naturally, also JIT compilers need to be updated
by this.
Before JIT conversion is being done, each compiler checks if A
is being loaded at startup to obtain information if it needs to
emit instructions to clear A first. Since BPF extensions are a
subset of BPF_LD | BPF_{W,H,B} | BPF_ABS variants, case statements
for extensions can be removed at that point. To ease and minimalize
code changes in the classic JITs, we have introduced bpf_anc_helper().
Tested with test_bpf on x86_64 (JIT, int), s390x (JIT, int),
arm (JIT, int), i368 (int), ppc64 (JIT, int); for sparc we
unfortunately didn't have access, but changes are analogous to
the rest.
Joint work with Alexei Starovoitov.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Mircea Gherzan <mgherzan@gmail.com>
Cc: Kees Cook <keescook@chromium.org>
Acked-by: Chema Gonzalez <chemag@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-29 02:22:50 -06:00
|
|
|
|
2014-06-24 07:33:22 -06:00
|
|
|
masks = kmalloc_array(flen, sizeof(*masks), GFP_KERNEL);
|
2010-12-01 13:46:24 -07:00
|
|
|
if (!masks)
|
|
|
|
return -ENOMEM;
|
net: filter: get rid of BPF_S_* enum
This patch finally allows us to get rid of the BPF_S_* enum.
Currently, the code performs unnecessary encode and decode
workarounds in seccomp and filter migration itself when a filter
is being attached in order to overcome BPF_S_* encoding which
is not used anymore by the new interpreter resp. JIT compilers.
Keeping it around would mean that also in future we would need
to extend and maintain this enum and related encoders/decoders.
We can get rid of all that and save us these operations during
filter attaching. Naturally, also JIT compilers need to be updated
by this.
Before JIT conversion is being done, each compiler checks if A
is being loaded at startup to obtain information if it needs to
emit instructions to clear A first. Since BPF extensions are a
subset of BPF_LD | BPF_{W,H,B} | BPF_ABS variants, case statements
for extensions can be removed at that point. To ease and minimalize
code changes in the classic JITs, we have introduced bpf_anc_helper().
Tested with test_bpf on x86_64 (JIT, int), s390x (JIT, int),
arm (JIT, int), i368 (int), ppc64 (JIT, int); for sparc we
unfortunately didn't have access, but changes are analogous to
the rest.
Joint work with Alexei Starovoitov.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Mircea Gherzan <mgherzan@gmail.com>
Cc: Kees Cook <keescook@chromium.org>
Acked-by: Chema Gonzalez <chemag@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-29 02:22:50 -06:00
|
|
|
|
2010-12-01 13:46:24 -07:00
|
|
|
memset(masks, 0xff, flen * sizeof(*masks));
|
|
|
|
|
|
|
|
for (pc = 0; pc < flen; pc++) {
|
|
|
|
memvalid &= masks[pc];
|
|
|
|
|
|
|
|
switch (filter[pc].code) {
|
net: filter: get rid of BPF_S_* enum
This patch finally allows us to get rid of the BPF_S_* enum.
Currently, the code performs unnecessary encode and decode
workarounds in seccomp and filter migration itself when a filter
is being attached in order to overcome BPF_S_* encoding which
is not used anymore by the new interpreter resp. JIT compilers.
Keeping it around would mean that also in future we would need
to extend and maintain this enum and related encoders/decoders.
We can get rid of all that and save us these operations during
filter attaching. Naturally, also JIT compilers need to be updated
by this.
Before JIT conversion is being done, each compiler checks if A
is being loaded at startup to obtain information if it needs to
emit instructions to clear A first. Since BPF extensions are a
subset of BPF_LD | BPF_{W,H,B} | BPF_ABS variants, case statements
for extensions can be removed at that point. To ease and minimalize
code changes in the classic JITs, we have introduced bpf_anc_helper().
Tested with test_bpf on x86_64 (JIT, int), s390x (JIT, int),
arm (JIT, int), i368 (int), ppc64 (JIT, int); for sparc we
unfortunately didn't have access, but changes are analogous to
the rest.
Joint work with Alexei Starovoitov.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Mircea Gherzan <mgherzan@gmail.com>
Cc: Kees Cook <keescook@chromium.org>
Acked-by: Chema Gonzalez <chemag@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-29 02:22:50 -06:00
|
|
|
case BPF_ST:
|
|
|
|
case BPF_STX:
|
2010-12-01 13:46:24 -07:00
|
|
|
memvalid |= (1 << filter[pc].k);
|
|
|
|
break;
|
net: filter: get rid of BPF_S_* enum
This patch finally allows us to get rid of the BPF_S_* enum.
Currently, the code performs unnecessary encode and decode
workarounds in seccomp and filter migration itself when a filter
is being attached in order to overcome BPF_S_* encoding which
is not used anymore by the new interpreter resp. JIT compilers.
Keeping it around would mean that also in future we would need
to extend and maintain this enum and related encoders/decoders.
We can get rid of all that and save us these operations during
filter attaching. Naturally, also JIT compilers need to be updated
by this.
Before JIT conversion is being done, each compiler checks if A
is being loaded at startup to obtain information if it needs to
emit instructions to clear A first. Since BPF extensions are a
subset of BPF_LD | BPF_{W,H,B} | BPF_ABS variants, case statements
for extensions can be removed at that point. To ease and minimalize
code changes in the classic JITs, we have introduced bpf_anc_helper().
Tested with test_bpf on x86_64 (JIT, int), s390x (JIT, int),
arm (JIT, int), i368 (int), ppc64 (JIT, int); for sparc we
unfortunately didn't have access, but changes are analogous to
the rest.
Joint work with Alexei Starovoitov.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Mircea Gherzan <mgherzan@gmail.com>
Cc: Kees Cook <keescook@chromium.org>
Acked-by: Chema Gonzalez <chemag@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-29 02:22:50 -06:00
|
|
|
case BPF_LD | BPF_MEM:
|
|
|
|
case BPF_LDX | BPF_MEM:
|
2010-12-01 13:46:24 -07:00
|
|
|
if (!(memvalid & (1 << filter[pc].k))) {
|
|
|
|
ret = -EINVAL;
|
|
|
|
goto error;
|
|
|
|
}
|
|
|
|
break;
|
net: filter: get rid of BPF_S_* enum
This patch finally allows us to get rid of the BPF_S_* enum.
Currently, the code performs unnecessary encode and decode
workarounds in seccomp and filter migration itself when a filter
is being attached in order to overcome BPF_S_* encoding which
is not used anymore by the new interpreter resp. JIT compilers.
Keeping it around would mean that also in future we would need
to extend and maintain this enum and related encoders/decoders.
We can get rid of all that and save us these operations during
filter attaching. Naturally, also JIT compilers need to be updated
by this.
Before JIT conversion is being done, each compiler checks if A
is being loaded at startup to obtain information if it needs to
emit instructions to clear A first. Since BPF extensions are a
subset of BPF_LD | BPF_{W,H,B} | BPF_ABS variants, case statements
for extensions can be removed at that point. To ease and minimalize
code changes in the classic JITs, we have introduced bpf_anc_helper().
Tested with test_bpf on x86_64 (JIT, int), s390x (JIT, int),
arm (JIT, int), i368 (int), ppc64 (JIT, int); for sparc we
unfortunately didn't have access, but changes are analogous to
the rest.
Joint work with Alexei Starovoitov.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Mircea Gherzan <mgherzan@gmail.com>
Cc: Kees Cook <keescook@chromium.org>
Acked-by: Chema Gonzalez <chemag@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-29 02:22:50 -06:00
|
|
|
case BPF_JMP | BPF_JA:
|
|
|
|
/* A jump must set masks on target */
|
2010-12-01 13:46:24 -07:00
|
|
|
masks[pc + 1 + filter[pc].k] &= memvalid;
|
|
|
|
memvalid = ~0;
|
|
|
|
break;
|
net: filter: get rid of BPF_S_* enum
This patch finally allows us to get rid of the BPF_S_* enum.
Currently, the code performs unnecessary encode and decode
workarounds in seccomp and filter migration itself when a filter
is being attached in order to overcome BPF_S_* encoding which
is not used anymore by the new interpreter resp. JIT compilers.
Keeping it around would mean that also in future we would need
to extend and maintain this enum and related encoders/decoders.
We can get rid of all that and save us these operations during
filter attaching. Naturally, also JIT compilers need to be updated
by this.
Before JIT conversion is being done, each compiler checks if A
is being loaded at startup to obtain information if it needs to
emit instructions to clear A first. Since BPF extensions are a
subset of BPF_LD | BPF_{W,H,B} | BPF_ABS variants, case statements
for extensions can be removed at that point. To ease and minimalize
code changes in the classic JITs, we have introduced bpf_anc_helper().
Tested with test_bpf on x86_64 (JIT, int), s390x (JIT, int),
arm (JIT, int), i368 (int), ppc64 (JIT, int); for sparc we
unfortunately didn't have access, but changes are analogous to
the rest.
Joint work with Alexei Starovoitov.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Mircea Gherzan <mgherzan@gmail.com>
Cc: Kees Cook <keescook@chromium.org>
Acked-by: Chema Gonzalez <chemag@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-29 02:22:50 -06:00
|
|
|
case BPF_JMP | BPF_JEQ | BPF_K:
|
|
|
|
case BPF_JMP | BPF_JEQ | BPF_X:
|
|
|
|
case BPF_JMP | BPF_JGE | BPF_K:
|
|
|
|
case BPF_JMP | BPF_JGE | BPF_X:
|
|
|
|
case BPF_JMP | BPF_JGT | BPF_K:
|
|
|
|
case BPF_JMP | BPF_JGT | BPF_X:
|
|
|
|
case BPF_JMP | BPF_JSET | BPF_K:
|
|
|
|
case BPF_JMP | BPF_JSET | BPF_X:
|
|
|
|
/* A jump must set masks on targets */
|
2010-12-01 13:46:24 -07:00
|
|
|
masks[pc + 1 + filter[pc].jt] &= memvalid;
|
|
|
|
masks[pc + 1 + filter[pc].jf] &= memvalid;
|
|
|
|
memvalid = ~0;
|
|
|
|
break;
|
|
|
|
}
|
|
|
|
}
|
|
|
|
error:
|
|
|
|
kfree(masks);
|
|
|
|
return ret;
|
|
|
|
}
|
|
|
|
|
net: filter: get rid of BPF_S_* enum
This patch finally allows us to get rid of the BPF_S_* enum.
Currently, the code performs unnecessary encode and decode
workarounds in seccomp and filter migration itself when a filter
is being attached in order to overcome BPF_S_* encoding which
is not used anymore by the new interpreter resp. JIT compilers.
Keeping it around would mean that also in future we would need
to extend and maintain this enum and related encoders/decoders.
We can get rid of all that and save us these operations during
filter attaching. Naturally, also JIT compilers need to be updated
by this.
Before JIT conversion is being done, each compiler checks if A
is being loaded at startup to obtain information if it needs to
emit instructions to clear A first. Since BPF extensions are a
subset of BPF_LD | BPF_{W,H,B} | BPF_ABS variants, case statements
for extensions can be removed at that point. To ease and minimalize
code changes in the classic JITs, we have introduced bpf_anc_helper().
Tested with test_bpf on x86_64 (JIT, int), s390x (JIT, int),
arm (JIT, int), i368 (int), ppc64 (JIT, int); for sparc we
unfortunately didn't have access, but changes are analogous to
the rest.
Joint work with Alexei Starovoitov.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Mircea Gherzan <mgherzan@gmail.com>
Cc: Kees Cook <keescook@chromium.org>
Acked-by: Chema Gonzalez <chemag@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-29 02:22:50 -06:00
|
|
|
static bool chk_code_allowed(u16 code_to_probe)
|
|
|
|
{
|
|
|
|
static const bool codes[] = {
|
|
|
|
/* 32 bit ALU operations */
|
|
|
|
[BPF_ALU | BPF_ADD | BPF_K] = true,
|
|
|
|
[BPF_ALU | BPF_ADD | BPF_X] = true,
|
|
|
|
[BPF_ALU | BPF_SUB | BPF_K] = true,
|
|
|
|
[BPF_ALU | BPF_SUB | BPF_X] = true,
|
|
|
|
[BPF_ALU | BPF_MUL | BPF_K] = true,
|
|
|
|
[BPF_ALU | BPF_MUL | BPF_X] = true,
|
|
|
|
[BPF_ALU | BPF_DIV | BPF_K] = true,
|
|
|
|
[BPF_ALU | BPF_DIV | BPF_X] = true,
|
|
|
|
[BPF_ALU | BPF_MOD | BPF_K] = true,
|
|
|
|
[BPF_ALU | BPF_MOD | BPF_X] = true,
|
|
|
|
[BPF_ALU | BPF_AND | BPF_K] = true,
|
|
|
|
[BPF_ALU | BPF_AND | BPF_X] = true,
|
|
|
|
[BPF_ALU | BPF_OR | BPF_K] = true,
|
|
|
|
[BPF_ALU | BPF_OR | BPF_X] = true,
|
|
|
|
[BPF_ALU | BPF_XOR | BPF_K] = true,
|
|
|
|
[BPF_ALU | BPF_XOR | BPF_X] = true,
|
|
|
|
[BPF_ALU | BPF_LSH | BPF_K] = true,
|
|
|
|
[BPF_ALU | BPF_LSH | BPF_X] = true,
|
|
|
|
[BPF_ALU | BPF_RSH | BPF_K] = true,
|
|
|
|
[BPF_ALU | BPF_RSH | BPF_X] = true,
|
|
|
|
[BPF_ALU | BPF_NEG] = true,
|
|
|
|
/* Load instructions */
|
|
|
|
[BPF_LD | BPF_W | BPF_ABS] = true,
|
|
|
|
[BPF_LD | BPF_H | BPF_ABS] = true,
|
|
|
|
[BPF_LD | BPF_B | BPF_ABS] = true,
|
|
|
|
[BPF_LD | BPF_W | BPF_LEN] = true,
|
|
|
|
[BPF_LD | BPF_W | BPF_IND] = true,
|
|
|
|
[BPF_LD | BPF_H | BPF_IND] = true,
|
|
|
|
[BPF_LD | BPF_B | BPF_IND] = true,
|
|
|
|
[BPF_LD | BPF_IMM] = true,
|
|
|
|
[BPF_LD | BPF_MEM] = true,
|
|
|
|
[BPF_LDX | BPF_W | BPF_LEN] = true,
|
|
|
|
[BPF_LDX | BPF_B | BPF_MSH] = true,
|
|
|
|
[BPF_LDX | BPF_IMM] = true,
|
|
|
|
[BPF_LDX | BPF_MEM] = true,
|
|
|
|
/* Store instructions */
|
|
|
|
[BPF_ST] = true,
|
|
|
|
[BPF_STX] = true,
|
|
|
|
/* Misc instructions */
|
|
|
|
[BPF_MISC | BPF_TAX] = true,
|
|
|
|
[BPF_MISC | BPF_TXA] = true,
|
|
|
|
/* Return instructions */
|
|
|
|
[BPF_RET | BPF_K] = true,
|
|
|
|
[BPF_RET | BPF_A] = true,
|
|
|
|
/* Jump instructions */
|
|
|
|
[BPF_JMP | BPF_JA] = true,
|
|
|
|
[BPF_JMP | BPF_JEQ | BPF_K] = true,
|
|
|
|
[BPF_JMP | BPF_JEQ | BPF_X] = true,
|
|
|
|
[BPF_JMP | BPF_JGE | BPF_K] = true,
|
|
|
|
[BPF_JMP | BPF_JGE | BPF_X] = true,
|
|
|
|
[BPF_JMP | BPF_JGT | BPF_K] = true,
|
|
|
|
[BPF_JMP | BPF_JGT | BPF_X] = true,
|
|
|
|
[BPF_JMP | BPF_JSET | BPF_K] = true,
|
|
|
|
[BPF_JMP | BPF_JSET | BPF_X] = true,
|
|
|
|
};
|
|
|
|
|
|
|
|
if (code_to_probe >= ARRAY_SIZE(codes))
|
|
|
|
return false;
|
|
|
|
|
|
|
|
return codes[code_to_probe];
|
|
|
|
}
|
|
|
|
|
2005-04-16 16:20:36 -06:00
|
|
|
/**
|
2014-07-30 21:34:14 -06:00
|
|
|
* bpf_check_classic - verify socket filter code
|
2005-04-16 16:20:36 -06:00
|
|
|
* @filter: filter to verify
|
|
|
|
* @flen: length of filter
|
|
|
|
*
|
|
|
|
* Check the user's filter code. If we let some ugly
|
|
|
|
* filter code slip through kaboom! The filter must contain
|
2006-01-04 14:58:36 -07:00
|
|
|
* no references or jumps that are out of range, no illegal
|
|
|
|
* instructions, and must end with a RET instruction.
|
2005-04-16 16:20:36 -06:00
|
|
|
*
|
2006-01-13 15:33:06 -07:00
|
|
|
* All jumps are forward as they are not signed.
|
|
|
|
*
|
|
|
|
* Returns 0 if the rule set is legal or -EINVAL if not.
|
2005-04-16 16:20:36 -06:00
|
|
|
*/
|
2015-05-06 08:12:28 -06:00
|
|
|
static int bpf_check_classic(const struct sock_filter *filter,
|
|
|
|
unsigned int flen)
|
2005-04-16 16:20:36 -06:00
|
|
|
{
|
net: filter: return -EINVAL if BPF_S_ANC* operation is not supported
Currently, we return -EINVAL for malformed or wrong BPF filters.
However, this is not done for BPF_S_ANC* operations, which makes it
more difficult to detect if it's actually supported or not by the
BPF machine. Therefore, we should also return -EINVAL if K is within
the SKF_AD_OFF universe and the ancillary operation did not match.
Why exactly is it needed? If tools such as libpcap/tcpdump want to
make use of new ancillary operations (like filtering VLAN in kernel
space), there is currently no sane way to test if this feature /
BPF_S_ANC* op is present or not, since no error is returned. This
patch will make life easier for that and allow for a proper usage
for user space applications.
There was concern, if this patch will break userland. Short answer: Yes
and no. Long answer: It will "break" only for code that calls ...
{ BPF_LD | BPF_(W|H|B) | BPF_ABS, 0, 0, <K> },
... where <K> is in [0xfffff000, 0xffffffff] _and_ <K> is *not* an
ancillary. And here comes the BUT: assuming some *old* code will have
such an instruction where <K> is between [0xfffff000, 0xffffffff] and
it doesn't know ancillary operations, then this will give a
non-expected / unwanted behavior as well (since we do not return the
BPF machine with 0 after a failed load_pointer(), which was the case
before introducing ancillary operations, but load sth. into the
accumulator instead, and continue with the next instruction, for
instance). Thus, user space code would already have been broken by
introducing ancillary operations into the BPF machine per se. Code
that does such a direct load, e.g. "load word at packet offset
0xffffffff into accumulator" ("ld [0xffffffff]") is quite broken,
isn't it? The whole assumption of ancillary operations is that no-one
intentionally calls things like "ld [0xffffffff]" and expect this
word to be loaded from such a packet offset. Hence, we can also safely
make use of this feature testing patch and facilitate application
development. Therefore, at least from this patch onwards, we have
*for sure* a check whether current or in future implemented BPF_S_ANC*
ops are supported in the kernel. Patch was tested on x86_64.
(Thanks to Eric for the previous review.)
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Reported-by: Ani Sinha <ani@aristanetworks.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-12-28 03:50:17 -07:00
|
|
|
bool anc_found;
|
net: filter: get rid of BPF_S_* enum
This patch finally allows us to get rid of the BPF_S_* enum.
Currently, the code performs unnecessary encode and decode
workarounds in seccomp and filter migration itself when a filter
is being attached in order to overcome BPF_S_* encoding which
is not used anymore by the new interpreter resp. JIT compilers.
Keeping it around would mean that also in future we would need
to extend and maintain this enum and related encoders/decoders.
We can get rid of all that and save us these operations during
filter attaching. Naturally, also JIT compilers need to be updated
by this.
Before JIT conversion is being done, each compiler checks if A
is being loaded at startup to obtain information if it needs to
emit instructions to clear A first. Since BPF extensions are a
subset of BPF_LD | BPF_{W,H,B} | BPF_ABS variants, case statements
for extensions can be removed at that point. To ease and minimalize
code changes in the classic JITs, we have introduced bpf_anc_helper().
Tested with test_bpf on x86_64 (JIT, int), s390x (JIT, int),
arm (JIT, int), i368 (int), ppc64 (JIT, int); for sparc we
unfortunately didn't have access, but changes are analogous to
the rest.
Joint work with Alexei Starovoitov.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Mircea Gherzan <mgherzan@gmail.com>
Cc: Kees Cook <keescook@chromium.org>
Acked-by: Chema Gonzalez <chemag@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-29 02:22:50 -06:00
|
|
|
int pc;
|
2005-04-16 16:20:36 -06:00
|
|
|
|
2005-12-27 14:57:59 -07:00
|
|
|
if (flen == 0 || flen > BPF_MAXINSNS)
|
2005-04-16 16:20:36 -06:00
|
|
|
return -EINVAL;
|
|
|
|
|
net: filter: get rid of BPF_S_* enum
This patch finally allows us to get rid of the BPF_S_* enum.
Currently, the code performs unnecessary encode and decode
workarounds in seccomp and filter migration itself when a filter
is being attached in order to overcome BPF_S_* encoding which
is not used anymore by the new interpreter resp. JIT compilers.
Keeping it around would mean that also in future we would need
to extend and maintain this enum and related encoders/decoders.
We can get rid of all that and save us these operations during
filter attaching. Naturally, also JIT compilers need to be updated
by this.
Before JIT conversion is being done, each compiler checks if A
is being loaded at startup to obtain information if it needs to
emit instructions to clear A first. Since BPF extensions are a
subset of BPF_LD | BPF_{W,H,B} | BPF_ABS variants, case statements
for extensions can be removed at that point. To ease and minimalize
code changes in the classic JITs, we have introduced bpf_anc_helper().
Tested with test_bpf on x86_64 (JIT, int), s390x (JIT, int),
arm (JIT, int), i368 (int), ppc64 (JIT, int); for sparc we
unfortunately didn't have access, but changes are analogous to
the rest.
Joint work with Alexei Starovoitov.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Mircea Gherzan <mgherzan@gmail.com>
Cc: Kees Cook <keescook@chromium.org>
Acked-by: Chema Gonzalez <chemag@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-29 02:22:50 -06:00
|
|
|
/* Check the filter code now */
|
2005-04-16 16:20:36 -06:00
|
|
|
for (pc = 0; pc < flen; pc++) {
|
2014-07-12 07:49:16 -06:00
|
|
|
const struct sock_filter *ftest = &filter[pc];
|
2006-01-04 14:58:36 -07:00
|
|
|
|
net: filter: get rid of BPF_S_* enum
This patch finally allows us to get rid of the BPF_S_* enum.
Currently, the code performs unnecessary encode and decode
workarounds in seccomp and filter migration itself when a filter
is being attached in order to overcome BPF_S_* encoding which
is not used anymore by the new interpreter resp. JIT compilers.
Keeping it around would mean that also in future we would need
to extend and maintain this enum and related encoders/decoders.
We can get rid of all that and save us these operations during
filter attaching. Naturally, also JIT compilers need to be updated
by this.
Before JIT conversion is being done, each compiler checks if A
is being loaded at startup to obtain information if it needs to
emit instructions to clear A first. Since BPF extensions are a
subset of BPF_LD | BPF_{W,H,B} | BPF_ABS variants, case statements
for extensions can be removed at that point. To ease and minimalize
code changes in the classic JITs, we have introduced bpf_anc_helper().
Tested with test_bpf on x86_64 (JIT, int), s390x (JIT, int),
arm (JIT, int), i368 (int), ppc64 (JIT, int); for sparc we
unfortunately didn't have access, but changes are analogous to
the rest.
Joint work with Alexei Starovoitov.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Mircea Gherzan <mgherzan@gmail.com>
Cc: Kees Cook <keescook@chromium.org>
Acked-by: Chema Gonzalez <chemag@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-29 02:22:50 -06:00
|
|
|
/* May we actually operate on this code? */
|
|
|
|
if (!chk_code_allowed(ftest->code))
|
2010-11-16 08:19:51 -07:00
|
|
|
return -EINVAL;
|
net: filter: get rid of BPF_S_* enum
This patch finally allows us to get rid of the BPF_S_* enum.
Currently, the code performs unnecessary encode and decode
workarounds in seccomp and filter migration itself when a filter
is being attached in order to overcome BPF_S_* encoding which
is not used anymore by the new interpreter resp. JIT compilers.
Keeping it around would mean that also in future we would need
to extend and maintain this enum and related encoders/decoders.
We can get rid of all that and save us these operations during
filter attaching. Naturally, also JIT compilers need to be updated
by this.
Before JIT conversion is being done, each compiler checks if A
is being loaded at startup to obtain information if it needs to
emit instructions to clear A first. Since BPF extensions are a
subset of BPF_LD | BPF_{W,H,B} | BPF_ABS variants, case statements
for extensions can be removed at that point. To ease and minimalize
code changes in the classic JITs, we have introduced bpf_anc_helper().
Tested with test_bpf on x86_64 (JIT, int), s390x (JIT, int),
arm (JIT, int), i368 (int), ppc64 (JIT, int); for sparc we
unfortunately didn't have access, but changes are analogous to
the rest.
Joint work with Alexei Starovoitov.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Mircea Gherzan <mgherzan@gmail.com>
Cc: Kees Cook <keescook@chromium.org>
Acked-by: Chema Gonzalez <chemag@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-29 02:22:50 -06:00
|
|
|
|
2006-01-04 14:58:36 -07:00
|
|
|
/* Some instructions need special checks */
|
net: filter: get rid of BPF_S_* enum
This patch finally allows us to get rid of the BPF_S_* enum.
Currently, the code performs unnecessary encode and decode
workarounds in seccomp and filter migration itself when a filter
is being attached in order to overcome BPF_S_* encoding which
is not used anymore by the new interpreter resp. JIT compilers.
Keeping it around would mean that also in future we would need
to extend and maintain this enum and related encoders/decoders.
We can get rid of all that and save us these operations during
filter attaching. Naturally, also JIT compilers need to be updated
by this.
Before JIT conversion is being done, each compiler checks if A
is being loaded at startup to obtain information if it needs to
emit instructions to clear A first. Since BPF extensions are a
subset of BPF_LD | BPF_{W,H,B} | BPF_ABS variants, case statements
for extensions can be removed at that point. To ease and minimalize
code changes in the classic JITs, we have introduced bpf_anc_helper().
Tested with test_bpf on x86_64 (JIT, int), s390x (JIT, int),
arm (JIT, int), i368 (int), ppc64 (JIT, int); for sparc we
unfortunately didn't have access, but changes are analogous to
the rest.
Joint work with Alexei Starovoitov.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Mircea Gherzan <mgherzan@gmail.com>
Cc: Kees Cook <keescook@chromium.org>
Acked-by: Chema Gonzalez <chemag@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-29 02:22:50 -06:00
|
|
|
switch (ftest->code) {
|
|
|
|
case BPF_ALU | BPF_DIV | BPF_K:
|
|
|
|
case BPF_ALU | BPF_MOD | BPF_K:
|
|
|
|
/* Check for division by zero */
|
2012-09-07 16:03:35 -06:00
|
|
|
if (ftest->k == 0)
|
|
|
|
return -EINVAL;
|
|
|
|
break;
|
2016-01-12 12:17:08 -07:00
|
|
|
case BPF_ALU | BPF_LSH | BPF_K:
|
|
|
|
case BPF_ALU | BPF_RSH | BPF_K:
|
|
|
|
if (ftest->k >= 32)
|
|
|
|
return -EINVAL;
|
|
|
|
break;
|
net: filter: get rid of BPF_S_* enum
This patch finally allows us to get rid of the BPF_S_* enum.
Currently, the code performs unnecessary encode and decode
workarounds in seccomp and filter migration itself when a filter
is being attached in order to overcome BPF_S_* encoding which
is not used anymore by the new interpreter resp. JIT compilers.
Keeping it around would mean that also in future we would need
to extend and maintain this enum and related encoders/decoders.
We can get rid of all that and save us these operations during
filter attaching. Naturally, also JIT compilers need to be updated
by this.
Before JIT conversion is being done, each compiler checks if A
is being loaded at startup to obtain information if it needs to
emit instructions to clear A first. Since BPF extensions are a
subset of BPF_LD | BPF_{W,H,B} | BPF_ABS variants, case statements
for extensions can be removed at that point. To ease and minimalize
code changes in the classic JITs, we have introduced bpf_anc_helper().
Tested with test_bpf on x86_64 (JIT, int), s390x (JIT, int),
arm (JIT, int), i368 (int), ppc64 (JIT, int); for sparc we
unfortunately didn't have access, but changes are analogous to
the rest.
Joint work with Alexei Starovoitov.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Mircea Gherzan <mgherzan@gmail.com>
Cc: Kees Cook <keescook@chromium.org>
Acked-by: Chema Gonzalez <chemag@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-29 02:22:50 -06:00
|
|
|
case BPF_LD | BPF_MEM:
|
|
|
|
case BPF_LDX | BPF_MEM:
|
|
|
|
case BPF_ST:
|
|
|
|
case BPF_STX:
|
|
|
|
/* Check for invalid memory addresses */
|
2006-01-04 14:58:36 -07:00
|
|
|
if (ftest->k >= BPF_MEMWORDS)
|
|
|
|
return -EINVAL;
|
|
|
|
break;
|
net: filter: get rid of BPF_S_* enum
This patch finally allows us to get rid of the BPF_S_* enum.
Currently, the code performs unnecessary encode and decode
workarounds in seccomp and filter migration itself when a filter
is being attached in order to overcome BPF_S_* encoding which
is not used anymore by the new interpreter resp. JIT compilers.
Keeping it around would mean that also in future we would need
to extend and maintain this enum and related encoders/decoders.
We can get rid of all that and save us these operations during
filter attaching. Naturally, also JIT compilers need to be updated
by this.
Before JIT conversion is being done, each compiler checks if A
is being loaded at startup to obtain information if it needs to
emit instructions to clear A first. Since BPF extensions are a
subset of BPF_LD | BPF_{W,H,B} | BPF_ABS variants, case statements
for extensions can be removed at that point. To ease and minimalize
code changes in the classic JITs, we have introduced bpf_anc_helper().
Tested with test_bpf on x86_64 (JIT, int), s390x (JIT, int),
arm (JIT, int), i368 (int), ppc64 (JIT, int); for sparc we
unfortunately didn't have access, but changes are analogous to
the rest.
Joint work with Alexei Starovoitov.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Mircea Gherzan <mgherzan@gmail.com>
Cc: Kees Cook <keescook@chromium.org>
Acked-by: Chema Gonzalez <chemag@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-29 02:22:50 -06:00
|
|
|
case BPF_JMP | BPF_JA:
|
|
|
|
/* Note, the large ftest->k might cause loops.
|
2006-01-04 14:58:36 -07:00
|
|
|
* Compare this with conditional jumps below,
|
|
|
|
* where offsets are limited. --ANK (981016)
|
|
|
|
*/
|
net: filter: get rid of BPF_S_* enum
This patch finally allows us to get rid of the BPF_S_* enum.
Currently, the code performs unnecessary encode and decode
workarounds in seccomp and filter migration itself when a filter
is being attached in order to overcome BPF_S_* encoding which
is not used anymore by the new interpreter resp. JIT compilers.
Keeping it around would mean that also in future we would need
to extend and maintain this enum and related encoders/decoders.
We can get rid of all that and save us these operations during
filter attaching. Naturally, also JIT compilers need to be updated
by this.
Before JIT conversion is being done, each compiler checks if A
is being loaded at startup to obtain information if it needs to
emit instructions to clear A first. Since BPF extensions are a
subset of BPF_LD | BPF_{W,H,B} | BPF_ABS variants, case statements
for extensions can be removed at that point. To ease and minimalize
code changes in the classic JITs, we have introduced bpf_anc_helper().
Tested with test_bpf on x86_64 (JIT, int), s390x (JIT, int),
arm (JIT, int), i368 (int), ppc64 (JIT, int); for sparc we
unfortunately didn't have access, but changes are analogous to
the rest.
Joint work with Alexei Starovoitov.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Mircea Gherzan <mgherzan@gmail.com>
Cc: Kees Cook <keescook@chromium.org>
Acked-by: Chema Gonzalez <chemag@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-29 02:22:50 -06:00
|
|
|
if (ftest->k >= (unsigned int)(flen - pc - 1))
|
2006-01-04 14:58:36 -07:00
|
|
|
return -EINVAL;
|
net: optimize Berkeley Packet Filter (BPF) processing
Gcc is currenlty not in the ability to optimize the switch statement in
sk_run_filter() because of dense case labels. This patch replace the
OR'd labels with ordered sequenced case labels. The sk_chk_filter()
function is modified to patch/replace the original OPCODES in a
ordered but equivalent form. gcc is now in the ability to transform the
switch statement in sk_run_filter into a jump table of complexity O(1).
Until this patch gcc generates a sequence of conditional branches (O(n) of 567
byte .text segment size (arch x86_64):
7ff: 8b 06 mov (%rsi),%eax
801: 66 83 f8 35 cmp $0x35,%ax
805: 0f 84 d0 02 00 00 je adb <sk_run_filter+0x31d>
80b: 0f 87 07 01 00 00 ja 918 <sk_run_filter+0x15a>
811: 66 83 f8 15 cmp $0x15,%ax
815: 0f 84 c5 02 00 00 je ae0 <sk_run_filter+0x322>
81b: 77 73 ja 890 <sk_run_filter+0xd2>
81d: 66 83 f8 04 cmp $0x4,%ax
821: 0f 84 17 02 00 00 je a3e <sk_run_filter+0x280>
827: 77 29 ja 852 <sk_run_filter+0x94>
829: 66 83 f8 01 cmp $0x1,%ax
[...]
With the modification the compiler translate the switch statement into
the following jump table fragment:
7ff: 66 83 3e 2c cmpw $0x2c,(%rsi)
803: 0f 87 1f 02 00 00 ja a28 <sk_run_filter+0x26a>
809: 0f b7 06 movzwl (%rsi),%eax
80c: ff 24 c5 00 00 00 00 jmpq *0x0(,%rax,8)
813: 44 89 e3 mov %r12d,%ebx
816: e9 43 03 00 00 jmpq b5e <sk_run_filter+0x3a0>
81b: 41 89 dc mov %ebx,%r12d
81e: e9 3b 03 00 00 jmpq b5e <sk_run_filter+0x3a0>
Furthermore, I reordered the instructions to reduce cache line misses by
order the most common instruction to the start.
Signed-off-by: Hagen Paul Pfeifer <hagen@jauu.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-19 11:05:36 -06:00
|
|
|
break;
|
net: filter: get rid of BPF_S_* enum
This patch finally allows us to get rid of the BPF_S_* enum.
Currently, the code performs unnecessary encode and decode
workarounds in seccomp and filter migration itself when a filter
is being attached in order to overcome BPF_S_* encoding which
is not used anymore by the new interpreter resp. JIT compilers.
Keeping it around would mean that also in future we would need
to extend and maintain this enum and related encoders/decoders.
We can get rid of all that and save us these operations during
filter attaching. Naturally, also JIT compilers need to be updated
by this.
Before JIT conversion is being done, each compiler checks if A
is being loaded at startup to obtain information if it needs to
emit instructions to clear A first. Since BPF extensions are a
subset of BPF_LD | BPF_{W,H,B} | BPF_ABS variants, case statements
for extensions can be removed at that point. To ease and minimalize
code changes in the classic JITs, we have introduced bpf_anc_helper().
Tested with test_bpf on x86_64 (JIT, int), s390x (JIT, int),
arm (JIT, int), i368 (int), ppc64 (JIT, int); for sparc we
unfortunately didn't have access, but changes are analogous to
the rest.
Joint work with Alexei Starovoitov.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Mircea Gherzan <mgherzan@gmail.com>
Cc: Kees Cook <keescook@chromium.org>
Acked-by: Chema Gonzalez <chemag@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-29 02:22:50 -06:00
|
|
|
case BPF_JMP | BPF_JEQ | BPF_K:
|
|
|
|
case BPF_JMP | BPF_JEQ | BPF_X:
|
|
|
|
case BPF_JMP | BPF_JGE | BPF_K:
|
|
|
|
case BPF_JMP | BPF_JGE | BPF_X:
|
|
|
|
case BPF_JMP | BPF_JGT | BPF_K:
|
|
|
|
case BPF_JMP | BPF_JGT | BPF_X:
|
|
|
|
case BPF_JMP | BPF_JSET | BPF_K:
|
|
|
|
case BPF_JMP | BPF_JSET | BPF_X:
|
|
|
|
/* Both conditionals must be safe */
|
2006-01-17 03:25:52 -07:00
|
|
|
if (pc + ftest->jt + 1 >= flen ||
|
2006-01-04 14:58:36 -07:00
|
|
|
pc + ftest->jf + 1 >= flen)
|
|
|
|
return -EINVAL;
|
2010-11-16 08:19:51 -07:00
|
|
|
break;
|
net: filter: get rid of BPF_S_* enum
This patch finally allows us to get rid of the BPF_S_* enum.
Currently, the code performs unnecessary encode and decode
workarounds in seccomp and filter migration itself when a filter
is being attached in order to overcome BPF_S_* encoding which
is not used anymore by the new interpreter resp. JIT compilers.
Keeping it around would mean that also in future we would need
to extend and maintain this enum and related encoders/decoders.
We can get rid of all that and save us these operations during
filter attaching. Naturally, also JIT compilers need to be updated
by this.
Before JIT conversion is being done, each compiler checks if A
is being loaded at startup to obtain information if it needs to
emit instructions to clear A first. Since BPF extensions are a
subset of BPF_LD | BPF_{W,H,B} | BPF_ABS variants, case statements
for extensions can be removed at that point. To ease and minimalize
code changes in the classic JITs, we have introduced bpf_anc_helper().
Tested with test_bpf on x86_64 (JIT, int), s390x (JIT, int),
arm (JIT, int), i368 (int), ppc64 (JIT, int); for sparc we
unfortunately didn't have access, but changes are analogous to
the rest.
Joint work with Alexei Starovoitov.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Mircea Gherzan <mgherzan@gmail.com>
Cc: Kees Cook <keescook@chromium.org>
Acked-by: Chema Gonzalez <chemag@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-29 02:22:50 -06:00
|
|
|
case BPF_LD | BPF_W | BPF_ABS:
|
|
|
|
case BPF_LD | BPF_H | BPF_ABS:
|
|
|
|
case BPF_LD | BPF_B | BPF_ABS:
|
net: filter: return -EINVAL if BPF_S_ANC* operation is not supported
Currently, we return -EINVAL for malformed or wrong BPF filters.
However, this is not done for BPF_S_ANC* operations, which makes it
more difficult to detect if it's actually supported or not by the
BPF machine. Therefore, we should also return -EINVAL if K is within
the SKF_AD_OFF universe and the ancillary operation did not match.
Why exactly is it needed? If tools such as libpcap/tcpdump want to
make use of new ancillary operations (like filtering VLAN in kernel
space), there is currently no sane way to test if this feature /
BPF_S_ANC* op is present or not, since no error is returned. This
patch will make life easier for that and allow for a proper usage
for user space applications.
There was concern, if this patch will break userland. Short answer: Yes
and no. Long answer: It will "break" only for code that calls ...
{ BPF_LD | BPF_(W|H|B) | BPF_ABS, 0, 0, <K> },
... where <K> is in [0xfffff000, 0xffffffff] _and_ <K> is *not* an
ancillary. And here comes the BUT: assuming some *old* code will have
such an instruction where <K> is between [0xfffff000, 0xffffffff] and
it doesn't know ancillary operations, then this will give a
non-expected / unwanted behavior as well (since we do not return the
BPF machine with 0 after a failed load_pointer(), which was the case
before introducing ancillary operations, but load sth. into the
accumulator instead, and continue with the next instruction, for
instance). Thus, user space code would already have been broken by
introducing ancillary operations into the BPF machine per se. Code
that does such a direct load, e.g. "load word at packet offset
0xffffffff into accumulator" ("ld [0xffffffff]") is quite broken,
isn't it? The whole assumption of ancillary operations is that no-one
intentionally calls things like "ld [0xffffffff]" and expect this
word to be loaded from such a packet offset. Hence, we can also safely
make use of this feature testing patch and facilitate application
development. Therefore, at least from this patch onwards, we have
*for sure* a check whether current or in future implemented BPF_S_ANC*
ops are supported in the kernel. Patch was tested on x86_64.
(Thanks to Eric for the previous review.)
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Reported-by: Ani Sinha <ani@aristanetworks.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-12-28 03:50:17 -07:00
|
|
|
anc_found = false;
|
net: filter: get rid of BPF_S_* enum
This patch finally allows us to get rid of the BPF_S_* enum.
Currently, the code performs unnecessary encode and decode
workarounds in seccomp and filter migration itself when a filter
is being attached in order to overcome BPF_S_* encoding which
is not used anymore by the new interpreter resp. JIT compilers.
Keeping it around would mean that also in future we would need
to extend and maintain this enum and related encoders/decoders.
We can get rid of all that and save us these operations during
filter attaching. Naturally, also JIT compilers need to be updated
by this.
Before JIT conversion is being done, each compiler checks if A
is being loaded at startup to obtain information if it needs to
emit instructions to clear A first. Since BPF extensions are a
subset of BPF_LD | BPF_{W,H,B} | BPF_ABS variants, case statements
for extensions can be removed at that point. To ease and minimalize
code changes in the classic JITs, we have introduced bpf_anc_helper().
Tested with test_bpf on x86_64 (JIT, int), s390x (JIT, int),
arm (JIT, int), i368 (int), ppc64 (JIT, int); for sparc we
unfortunately didn't have access, but changes are analogous to
the rest.
Joint work with Alexei Starovoitov.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Mircea Gherzan <mgherzan@gmail.com>
Cc: Kees Cook <keescook@chromium.org>
Acked-by: Chema Gonzalez <chemag@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-29 02:22:50 -06:00
|
|
|
if (bpf_anc_helper(ftest) & BPF_ANC)
|
|
|
|
anc_found = true;
|
|
|
|
/* Ancillary operation unknown or unsupported */
|
net: filter: return -EINVAL if BPF_S_ANC* operation is not supported
Currently, we return -EINVAL for malformed or wrong BPF filters.
However, this is not done for BPF_S_ANC* operations, which makes it
more difficult to detect if it's actually supported or not by the
BPF machine. Therefore, we should also return -EINVAL if K is within
the SKF_AD_OFF universe and the ancillary operation did not match.
Why exactly is it needed? If tools such as libpcap/tcpdump want to
make use of new ancillary operations (like filtering VLAN in kernel
space), there is currently no sane way to test if this feature /
BPF_S_ANC* op is present or not, since no error is returned. This
patch will make life easier for that and allow for a proper usage
for user space applications.
There was concern, if this patch will break userland. Short answer: Yes
and no. Long answer: It will "break" only for code that calls ...
{ BPF_LD | BPF_(W|H|B) | BPF_ABS, 0, 0, <K> },
... where <K> is in [0xfffff000, 0xffffffff] _and_ <K> is *not* an
ancillary. And here comes the BUT: assuming some *old* code will have
such an instruction where <K> is between [0xfffff000, 0xffffffff] and
it doesn't know ancillary operations, then this will give a
non-expected / unwanted behavior as well (since we do not return the
BPF machine with 0 after a failed load_pointer(), which was the case
before introducing ancillary operations, but load sth. into the
accumulator instead, and continue with the next instruction, for
instance). Thus, user space code would already have been broken by
introducing ancillary operations into the BPF machine per se. Code
that does such a direct load, e.g. "load word at packet offset
0xffffffff into accumulator" ("ld [0xffffffff]") is quite broken,
isn't it? The whole assumption of ancillary operations is that no-one
intentionally calls things like "ld [0xffffffff]" and expect this
word to be loaded from such a packet offset. Hence, we can also safely
make use of this feature testing patch and facilitate application
development. Therefore, at least from this patch onwards, we have
*for sure* a check whether current or in future implemented BPF_S_ANC*
ops are supported in the kernel. Patch was tested on x86_64.
(Thanks to Eric for the previous review.)
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Reported-by: Ani Sinha <ani@aristanetworks.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-12-28 03:50:17 -07:00
|
|
|
if (anc_found == false && ftest->k >= SKF_AD_OFF)
|
|
|
|
return -EINVAL;
|
net: optimize Berkeley Packet Filter (BPF) processing
Gcc is currenlty not in the ability to optimize the switch statement in
sk_run_filter() because of dense case labels. This patch replace the
OR'd labels with ordered sequenced case labels. The sk_chk_filter()
function is modified to patch/replace the original OPCODES in a
ordered but equivalent form. gcc is now in the ability to transform the
switch statement in sk_run_filter into a jump table of complexity O(1).
Until this patch gcc generates a sequence of conditional branches (O(n) of 567
byte .text segment size (arch x86_64):
7ff: 8b 06 mov (%rsi),%eax
801: 66 83 f8 35 cmp $0x35,%ax
805: 0f 84 d0 02 00 00 je adb <sk_run_filter+0x31d>
80b: 0f 87 07 01 00 00 ja 918 <sk_run_filter+0x15a>
811: 66 83 f8 15 cmp $0x15,%ax
815: 0f 84 c5 02 00 00 je ae0 <sk_run_filter+0x322>
81b: 77 73 ja 890 <sk_run_filter+0xd2>
81d: 66 83 f8 04 cmp $0x4,%ax
821: 0f 84 17 02 00 00 je a3e <sk_run_filter+0x280>
827: 77 29 ja 852 <sk_run_filter+0x94>
829: 66 83 f8 01 cmp $0x1,%ax
[...]
With the modification the compiler translate the switch statement into
the following jump table fragment:
7ff: 66 83 3e 2c cmpw $0x2c,(%rsi)
803: 0f 87 1f 02 00 00 ja a28 <sk_run_filter+0x26a>
809: 0f b7 06 movzwl (%rsi),%eax
80c: ff 24 c5 00 00 00 00 jmpq *0x0(,%rax,8)
813: 44 89 e3 mov %r12d,%ebx
816: e9 43 03 00 00 jmpq b5e <sk_run_filter+0x3a0>
81b: 41 89 dc mov %ebx,%r12d
81e: e9 3b 03 00 00 jmpq b5e <sk_run_filter+0x3a0>
Furthermore, I reordered the instructions to reduce cache line misses by
order the most common instruction to the start.
Signed-off-by: Hagen Paul Pfeifer <hagen@jauu.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-19 11:05:36 -06:00
|
|
|
}
|
|
|
|
}
|
2006-01-04 14:58:36 -07:00
|
|
|
|
net: filter: get rid of BPF_S_* enum
This patch finally allows us to get rid of the BPF_S_* enum.
Currently, the code performs unnecessary encode and decode
workarounds in seccomp and filter migration itself when a filter
is being attached in order to overcome BPF_S_* encoding which
is not used anymore by the new interpreter resp. JIT compilers.
Keeping it around would mean that also in future we would need
to extend and maintain this enum and related encoders/decoders.
We can get rid of all that and save us these operations during
filter attaching. Naturally, also JIT compilers need to be updated
by this.
Before JIT conversion is being done, each compiler checks if A
is being loaded at startup to obtain information if it needs to
emit instructions to clear A first. Since BPF extensions are a
subset of BPF_LD | BPF_{W,H,B} | BPF_ABS variants, case statements
for extensions can be removed at that point. To ease and minimalize
code changes in the classic JITs, we have introduced bpf_anc_helper().
Tested with test_bpf on x86_64 (JIT, int), s390x (JIT, int),
arm (JIT, int), i368 (int), ppc64 (JIT, int); for sparc we
unfortunately didn't have access, but changes are analogous to
the rest.
Joint work with Alexei Starovoitov.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Mircea Gherzan <mgherzan@gmail.com>
Cc: Kees Cook <keescook@chromium.org>
Acked-by: Chema Gonzalez <chemag@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-29 02:22:50 -06:00
|
|
|
/* Last instruction must be a RET code */
|
net: optimize Berkeley Packet Filter (BPF) processing
Gcc is currenlty not in the ability to optimize the switch statement in
sk_run_filter() because of dense case labels. This patch replace the
OR'd labels with ordered sequenced case labels. The sk_chk_filter()
function is modified to patch/replace the original OPCODES in a
ordered but equivalent form. gcc is now in the ability to transform the
switch statement in sk_run_filter into a jump table of complexity O(1).
Until this patch gcc generates a sequence of conditional branches (O(n) of 567
byte .text segment size (arch x86_64):
7ff: 8b 06 mov (%rsi),%eax
801: 66 83 f8 35 cmp $0x35,%ax
805: 0f 84 d0 02 00 00 je adb <sk_run_filter+0x31d>
80b: 0f 87 07 01 00 00 ja 918 <sk_run_filter+0x15a>
811: 66 83 f8 15 cmp $0x15,%ax
815: 0f 84 c5 02 00 00 je ae0 <sk_run_filter+0x322>
81b: 77 73 ja 890 <sk_run_filter+0xd2>
81d: 66 83 f8 04 cmp $0x4,%ax
821: 0f 84 17 02 00 00 je a3e <sk_run_filter+0x280>
827: 77 29 ja 852 <sk_run_filter+0x94>
829: 66 83 f8 01 cmp $0x1,%ax
[...]
With the modification the compiler translate the switch statement into
the following jump table fragment:
7ff: 66 83 3e 2c cmpw $0x2c,(%rsi)
803: 0f 87 1f 02 00 00 ja a28 <sk_run_filter+0x26a>
809: 0f b7 06 movzwl (%rsi),%eax
80c: ff 24 c5 00 00 00 00 jmpq *0x0(,%rax,8)
813: 44 89 e3 mov %r12d,%ebx
816: e9 43 03 00 00 jmpq b5e <sk_run_filter+0x3a0>
81b: 41 89 dc mov %ebx,%r12d
81e: e9 3b 03 00 00 jmpq b5e <sk_run_filter+0x3a0>
Furthermore, I reordered the instructions to reduce cache line misses by
order the most common instruction to the start.
Signed-off-by: Hagen Paul Pfeifer <hagen@jauu.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-19 11:05:36 -06:00
|
|
|
switch (filter[flen - 1].code) {
|
net: filter: get rid of BPF_S_* enum
This patch finally allows us to get rid of the BPF_S_* enum.
Currently, the code performs unnecessary encode and decode
workarounds in seccomp and filter migration itself when a filter
is being attached in order to overcome BPF_S_* encoding which
is not used anymore by the new interpreter resp. JIT compilers.
Keeping it around would mean that also in future we would need
to extend and maintain this enum and related encoders/decoders.
We can get rid of all that and save us these operations during
filter attaching. Naturally, also JIT compilers need to be updated
by this.
Before JIT conversion is being done, each compiler checks if A
is being loaded at startup to obtain information if it needs to
emit instructions to clear A first. Since BPF extensions are a
subset of BPF_LD | BPF_{W,H,B} | BPF_ABS variants, case statements
for extensions can be removed at that point. To ease and minimalize
code changes in the classic JITs, we have introduced bpf_anc_helper().
Tested with test_bpf on x86_64 (JIT, int), s390x (JIT, int),
arm (JIT, int), i368 (int), ppc64 (JIT, int); for sparc we
unfortunately didn't have access, but changes are analogous to
the rest.
Joint work with Alexei Starovoitov.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Mircea Gherzan <mgherzan@gmail.com>
Cc: Kees Cook <keescook@chromium.org>
Acked-by: Chema Gonzalez <chemag@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-29 02:22:50 -06:00
|
|
|
case BPF_RET | BPF_K:
|
|
|
|
case BPF_RET | BPF_A:
|
2010-12-01 13:46:24 -07:00
|
|
|
return check_load_and_stores(filter, flen);
|
2010-11-16 08:19:51 -07:00
|
|
|
}
|
net: filter: get rid of BPF_S_* enum
This patch finally allows us to get rid of the BPF_S_* enum.
Currently, the code performs unnecessary encode and decode
workarounds in seccomp and filter migration itself when a filter
is being attached in order to overcome BPF_S_* encoding which
is not used anymore by the new interpreter resp. JIT compilers.
Keeping it around would mean that also in future we would need
to extend and maintain this enum and related encoders/decoders.
We can get rid of all that and save us these operations during
filter attaching. Naturally, also JIT compilers need to be updated
by this.
Before JIT conversion is being done, each compiler checks if A
is being loaded at startup to obtain information if it needs to
emit instructions to clear A first. Since BPF extensions are a
subset of BPF_LD | BPF_{W,H,B} | BPF_ABS variants, case statements
for extensions can be removed at that point. To ease and minimalize
code changes in the classic JITs, we have introduced bpf_anc_helper().
Tested with test_bpf on x86_64 (JIT, int), s390x (JIT, int),
arm (JIT, int), i368 (int), ppc64 (JIT, int); for sparc we
unfortunately didn't have access, but changes are analogous to
the rest.
Joint work with Alexei Starovoitov.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Mircea Gherzan <mgherzan@gmail.com>
Cc: Kees Cook <keescook@chromium.org>
Acked-by: Chema Gonzalez <chemag@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-29 02:22:50 -06:00
|
|
|
|
2010-11-16 08:19:51 -07:00
|
|
|
return -EINVAL;
|
2005-04-16 16:20:36 -06:00
|
|
|
}
|
|
|
|
|
net: filter: split 'struct sk_filter' into socket and bpf parts
clean up names related to socket filtering and bpf in the following way:
- everything that deals with sockets keeps 'sk_*' prefix
- everything that is pure BPF is changed to 'bpf_*' prefix
split 'struct sk_filter' into
struct sk_filter {
atomic_t refcnt;
struct rcu_head rcu;
struct bpf_prog *prog;
};
and
struct bpf_prog {
u32 jited:1,
len:31;
struct sock_fprog_kern *orig_prog;
unsigned int (*bpf_func)(const struct sk_buff *skb,
const struct bpf_insn *filter);
union {
struct sock_filter insns[0];
struct bpf_insn insnsi[0];
struct work_struct work;
};
};
so that 'struct bpf_prog' can be used independent of sockets and cleans up
'unattached' bpf use cases
split SK_RUN_FILTER macro into:
SK_RUN_FILTER to be used with 'struct sk_filter *' and
BPF_PROG_RUN to be used with 'struct bpf_prog *'
__sk_filter_release(struct sk_filter *) gains
__bpf_prog_release(struct bpf_prog *) helper function
also perform related renames for the functions that work
with 'struct bpf_prog *', since they're on the same lines:
sk_filter_size -> bpf_prog_size
sk_filter_select_runtime -> bpf_prog_select_runtime
sk_filter_free -> bpf_prog_free
sk_unattached_filter_create -> bpf_prog_create
sk_unattached_filter_destroy -> bpf_prog_destroy
sk_store_orig_filter -> bpf_prog_store_orig_filter
sk_release_orig_filter -> bpf_release_orig_filter
__sk_migrate_filter -> bpf_migrate_filter
__sk_prepare_filter -> bpf_prepare_filter
API for attaching classic BPF to a socket stays the same:
sk_attach_filter(prog, struct sock *)/sk_detach_filter(struct sock *)
and SK_RUN_FILTER(struct sk_filter *, ctx) to execute a program
which is used by sockets, tun, af_packet
API for 'unattached' BPF programs becomes:
bpf_prog_create(struct bpf_prog **)/bpf_prog_destroy(struct bpf_prog *)
and BPF_PROG_RUN(struct bpf_prog *, ctx) to execute a program
which is used by isdn, ppp, team, seccomp, ptp, xt_bpf, cls_bpf, test_bpf
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-30 21:34:16 -06:00
|
|
|
static int bpf_prog_store_orig_filter(struct bpf_prog *fp,
|
|
|
|
const struct sock_fprog *fprog)
|
net: filter: keep original BPF program around
In order to open up the possibility to internally transform a BPF program
into an alternative and possibly non-trivial reversible representation, we
need to keep the original BPF program around, so that it can be passed back
to user space w/o the need of a complex decoder.
The reason for that use case resides in commit a8fc92778080 ("sk-filter:
Add ability to get socket filter program (v2)"), that is, the ability
to retrieve the currently attached BPF filter from a given socket used
mainly by the checkpoint-restore project, for example.
Therefore, we add two helpers sk_{store,release}_orig_filter for taking
care of that. In the sk_unattached_filter_create() case, there's no such
possibility/requirement to retrieve a loaded BPF program. Therefore, we
can spare us the work in that case.
This approach will simplify and slightly speed up both, sk_get_filter()
and sock_diag_put_filterinfo() handlers as we won't need to successively
decode filters anymore through sk_decode_filter(). As we still need
sk_decode_filter() later on, we're keeping it around.
Joint work with Alexei Starovoitov.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:19 -06:00
|
|
|
{
|
2014-07-30 21:34:13 -06:00
|
|
|
unsigned int fsize = bpf_classic_proglen(fprog);
|
net: filter: keep original BPF program around
In order to open up the possibility to internally transform a BPF program
into an alternative and possibly non-trivial reversible representation, we
need to keep the original BPF program around, so that it can be passed back
to user space w/o the need of a complex decoder.
The reason for that use case resides in commit a8fc92778080 ("sk-filter:
Add ability to get socket filter program (v2)"), that is, the ability
to retrieve the currently attached BPF filter from a given socket used
mainly by the checkpoint-restore project, for example.
Therefore, we add two helpers sk_{store,release}_orig_filter for taking
care of that. In the sk_unattached_filter_create() case, there's no such
possibility/requirement to retrieve a loaded BPF program. Therefore, we
can spare us the work in that case.
This approach will simplify and slightly speed up both, sk_get_filter()
and sock_diag_put_filterinfo() handlers as we won't need to successively
decode filters anymore through sk_decode_filter(). As we still need
sk_decode_filter() later on, we're keeping it around.
Joint work with Alexei Starovoitov.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:19 -06:00
|
|
|
struct sock_fprog_kern *fkprog;
|
|
|
|
|
|
|
|
fp->orig_prog = kmalloc(sizeof(*fkprog), GFP_KERNEL);
|
|
|
|
if (!fp->orig_prog)
|
|
|
|
return -ENOMEM;
|
|
|
|
|
|
|
|
fkprog = fp->orig_prog;
|
|
|
|
fkprog->len = fprog->len;
|
2015-05-06 08:12:29 -06:00
|
|
|
|
|
|
|
fkprog->filter = kmemdup(fp->insns, fsize,
|
|
|
|
GFP_KERNEL | __GFP_NOWARN);
|
net: filter: keep original BPF program around
In order to open up the possibility to internally transform a BPF program
into an alternative and possibly non-trivial reversible representation, we
need to keep the original BPF program around, so that it can be passed back
to user space w/o the need of a complex decoder.
The reason for that use case resides in commit a8fc92778080 ("sk-filter:
Add ability to get socket filter program (v2)"), that is, the ability
to retrieve the currently attached BPF filter from a given socket used
mainly by the checkpoint-restore project, for example.
Therefore, we add two helpers sk_{store,release}_orig_filter for taking
care of that. In the sk_unattached_filter_create() case, there's no such
possibility/requirement to retrieve a loaded BPF program. Therefore, we
can spare us the work in that case.
This approach will simplify and slightly speed up both, sk_get_filter()
and sock_diag_put_filterinfo() handlers as we won't need to successively
decode filters anymore through sk_decode_filter(). As we still need
sk_decode_filter() later on, we're keeping it around.
Joint work with Alexei Starovoitov.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:19 -06:00
|
|
|
if (!fkprog->filter) {
|
|
|
|
kfree(fp->orig_prog);
|
|
|
|
return -ENOMEM;
|
|
|
|
}
|
|
|
|
|
|
|
|
return 0;
|
|
|
|
}
|
|
|
|
|
net: filter: split 'struct sk_filter' into socket and bpf parts
clean up names related to socket filtering and bpf in the following way:
- everything that deals with sockets keeps 'sk_*' prefix
- everything that is pure BPF is changed to 'bpf_*' prefix
split 'struct sk_filter' into
struct sk_filter {
atomic_t refcnt;
struct rcu_head rcu;
struct bpf_prog *prog;
};
and
struct bpf_prog {
u32 jited:1,
len:31;
struct sock_fprog_kern *orig_prog;
unsigned int (*bpf_func)(const struct sk_buff *skb,
const struct bpf_insn *filter);
union {
struct sock_filter insns[0];
struct bpf_insn insnsi[0];
struct work_struct work;
};
};
so that 'struct bpf_prog' can be used independent of sockets and cleans up
'unattached' bpf use cases
split SK_RUN_FILTER macro into:
SK_RUN_FILTER to be used with 'struct sk_filter *' and
BPF_PROG_RUN to be used with 'struct bpf_prog *'
__sk_filter_release(struct sk_filter *) gains
__bpf_prog_release(struct bpf_prog *) helper function
also perform related renames for the functions that work
with 'struct bpf_prog *', since they're on the same lines:
sk_filter_size -> bpf_prog_size
sk_filter_select_runtime -> bpf_prog_select_runtime
sk_filter_free -> bpf_prog_free
sk_unattached_filter_create -> bpf_prog_create
sk_unattached_filter_destroy -> bpf_prog_destroy
sk_store_orig_filter -> bpf_prog_store_orig_filter
sk_release_orig_filter -> bpf_release_orig_filter
__sk_migrate_filter -> bpf_migrate_filter
__sk_prepare_filter -> bpf_prepare_filter
API for attaching classic BPF to a socket stays the same:
sk_attach_filter(prog, struct sock *)/sk_detach_filter(struct sock *)
and SK_RUN_FILTER(struct sk_filter *, ctx) to execute a program
which is used by sockets, tun, af_packet
API for 'unattached' BPF programs becomes:
bpf_prog_create(struct bpf_prog **)/bpf_prog_destroy(struct bpf_prog *)
and BPF_PROG_RUN(struct bpf_prog *, ctx) to execute a program
which is used by isdn, ppp, team, seccomp, ptp, xt_bpf, cls_bpf, test_bpf
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-30 21:34:16 -06:00
|
|
|
static void bpf_release_orig_filter(struct bpf_prog *fp)
|
net: filter: keep original BPF program around
In order to open up the possibility to internally transform a BPF program
into an alternative and possibly non-trivial reversible representation, we
need to keep the original BPF program around, so that it can be passed back
to user space w/o the need of a complex decoder.
The reason for that use case resides in commit a8fc92778080 ("sk-filter:
Add ability to get socket filter program (v2)"), that is, the ability
to retrieve the currently attached BPF filter from a given socket used
mainly by the checkpoint-restore project, for example.
Therefore, we add two helpers sk_{store,release}_orig_filter for taking
care of that. In the sk_unattached_filter_create() case, there's no such
possibility/requirement to retrieve a loaded BPF program. Therefore, we
can spare us the work in that case.
This approach will simplify and slightly speed up both, sk_get_filter()
and sock_diag_put_filterinfo() handlers as we won't need to successively
decode filters anymore through sk_decode_filter(). As we still need
sk_decode_filter() later on, we're keeping it around.
Joint work with Alexei Starovoitov.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:19 -06:00
|
|
|
{
|
|
|
|
struct sock_fprog_kern *fprog = fp->orig_prog;
|
|
|
|
|
|
|
|
if (fprog) {
|
|
|
|
kfree(fprog->filter);
|
|
|
|
kfree(fprog);
|
|
|
|
}
|
|
|
|
}
|
|
|
|
|
net: filter: split 'struct sk_filter' into socket and bpf parts
clean up names related to socket filtering and bpf in the following way:
- everything that deals with sockets keeps 'sk_*' prefix
- everything that is pure BPF is changed to 'bpf_*' prefix
split 'struct sk_filter' into
struct sk_filter {
atomic_t refcnt;
struct rcu_head rcu;
struct bpf_prog *prog;
};
and
struct bpf_prog {
u32 jited:1,
len:31;
struct sock_fprog_kern *orig_prog;
unsigned int (*bpf_func)(const struct sk_buff *skb,
const struct bpf_insn *filter);
union {
struct sock_filter insns[0];
struct bpf_insn insnsi[0];
struct work_struct work;
};
};
so that 'struct bpf_prog' can be used independent of sockets and cleans up
'unattached' bpf use cases
split SK_RUN_FILTER macro into:
SK_RUN_FILTER to be used with 'struct sk_filter *' and
BPF_PROG_RUN to be used with 'struct bpf_prog *'
__sk_filter_release(struct sk_filter *) gains
__bpf_prog_release(struct bpf_prog *) helper function
also perform related renames for the functions that work
with 'struct bpf_prog *', since they're on the same lines:
sk_filter_size -> bpf_prog_size
sk_filter_select_runtime -> bpf_prog_select_runtime
sk_filter_free -> bpf_prog_free
sk_unattached_filter_create -> bpf_prog_create
sk_unattached_filter_destroy -> bpf_prog_destroy
sk_store_orig_filter -> bpf_prog_store_orig_filter
sk_release_orig_filter -> bpf_release_orig_filter
__sk_migrate_filter -> bpf_migrate_filter
__sk_prepare_filter -> bpf_prepare_filter
API for attaching classic BPF to a socket stays the same:
sk_attach_filter(prog, struct sock *)/sk_detach_filter(struct sock *)
and SK_RUN_FILTER(struct sk_filter *, ctx) to execute a program
which is used by sockets, tun, af_packet
API for 'unattached' BPF programs becomes:
bpf_prog_create(struct bpf_prog **)/bpf_prog_destroy(struct bpf_prog *)
and BPF_PROG_RUN(struct bpf_prog *, ctx) to execute a program
which is used by isdn, ppp, team, seccomp, ptp, xt_bpf, cls_bpf, test_bpf
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-30 21:34:16 -06:00
|
|
|
static void __bpf_prog_release(struct bpf_prog *prog)
|
|
|
|
{
|
2015-03-01 04:31:47 -07:00
|
|
|
if (prog->type == BPF_PROG_TYPE_SOCKET_FILTER) {
|
2014-12-01 16:06:35 -07:00
|
|
|
bpf_prog_put(prog);
|
|
|
|
} else {
|
|
|
|
bpf_release_orig_filter(prog);
|
|
|
|
bpf_prog_free(prog);
|
|
|
|
}
|
net: filter: split 'struct sk_filter' into socket and bpf parts
clean up names related to socket filtering and bpf in the following way:
- everything that deals with sockets keeps 'sk_*' prefix
- everything that is pure BPF is changed to 'bpf_*' prefix
split 'struct sk_filter' into
struct sk_filter {
atomic_t refcnt;
struct rcu_head rcu;
struct bpf_prog *prog;
};
and
struct bpf_prog {
u32 jited:1,
len:31;
struct sock_fprog_kern *orig_prog;
unsigned int (*bpf_func)(const struct sk_buff *skb,
const struct bpf_insn *filter);
union {
struct sock_filter insns[0];
struct bpf_insn insnsi[0];
struct work_struct work;
};
};
so that 'struct bpf_prog' can be used independent of sockets and cleans up
'unattached' bpf use cases
split SK_RUN_FILTER macro into:
SK_RUN_FILTER to be used with 'struct sk_filter *' and
BPF_PROG_RUN to be used with 'struct bpf_prog *'
__sk_filter_release(struct sk_filter *) gains
__bpf_prog_release(struct bpf_prog *) helper function
also perform related renames for the functions that work
with 'struct bpf_prog *', since they're on the same lines:
sk_filter_size -> bpf_prog_size
sk_filter_select_runtime -> bpf_prog_select_runtime
sk_filter_free -> bpf_prog_free
sk_unattached_filter_create -> bpf_prog_create
sk_unattached_filter_destroy -> bpf_prog_destroy
sk_store_orig_filter -> bpf_prog_store_orig_filter
sk_release_orig_filter -> bpf_release_orig_filter
__sk_migrate_filter -> bpf_migrate_filter
__sk_prepare_filter -> bpf_prepare_filter
API for attaching classic BPF to a socket stays the same:
sk_attach_filter(prog, struct sock *)/sk_detach_filter(struct sock *)
and SK_RUN_FILTER(struct sk_filter *, ctx) to execute a program
which is used by sockets, tun, af_packet
API for 'unattached' BPF programs becomes:
bpf_prog_create(struct bpf_prog **)/bpf_prog_destroy(struct bpf_prog *)
and BPF_PROG_RUN(struct bpf_prog *, ctx) to execute a program
which is used by isdn, ppp, team, seccomp, ptp, xt_bpf, cls_bpf, test_bpf
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-30 21:34:16 -06:00
|
|
|
}
|
|
|
|
|
net: filter: don't release unattached filter through call_rcu()
sk_unattached_filter_destroy() does not always need to release the
filter object via rcu. Since this filter is never attached to the
socket, the caller should be responsible for releasing the filter
in a safe way, which may not necessarily imply rcu.
This is a short summary of clients of this function:
1) xt_bpf.c and cls_bpf.c use the bpf matchers from rules, these rules
are removed from the packet path before the filter is released. Thus,
the framework makes sure the filter is safely removed.
2) In the ppp driver, the ppp_lock ensures serialization between the
xmit and filter attachment/detachment path. This doesn't use rcu
so deferred release via rcu makes no sense.
3) In the isdn/ppp driver, it is called from isdn_ppp_release()
the isdn_ppp_ioctl(). This driver uses mutex and spinlocks, no rcu.
Thus, deferred rcu makes no sense to me either, the deferred releases
may be just masking the effects of wrong locking strategy, which
should be fixed in the driver itself.
4) In the team driver, this is the only place where the rcu
synchronization with unattached filter is used. Therefore, this
patch introduces synchronize_rcu() which is called from the
genetlink path to make sure the filter doesn't go away while packets
are still walking over it. I think we can revisit this once struct
bpf_prog (that only wraps specific bpf code bits) is in place, then
add some specific struct rcu_head in the scope of the team driver if
Jiri thinks this is needed.
Deferred rcu release for unattached filters was originally introduced
in 302d663 ("filter: Allow to create sk-unattached filters").
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-29 09:36:28 -06:00
|
|
|
static void __sk_filter_release(struct sk_filter *fp)
|
|
|
|
{
|
net: filter: split 'struct sk_filter' into socket and bpf parts
clean up names related to socket filtering and bpf in the following way:
- everything that deals with sockets keeps 'sk_*' prefix
- everything that is pure BPF is changed to 'bpf_*' prefix
split 'struct sk_filter' into
struct sk_filter {
atomic_t refcnt;
struct rcu_head rcu;
struct bpf_prog *prog;
};
and
struct bpf_prog {
u32 jited:1,
len:31;
struct sock_fprog_kern *orig_prog;
unsigned int (*bpf_func)(const struct sk_buff *skb,
const struct bpf_insn *filter);
union {
struct sock_filter insns[0];
struct bpf_insn insnsi[0];
struct work_struct work;
};
};
so that 'struct bpf_prog' can be used independent of sockets and cleans up
'unattached' bpf use cases
split SK_RUN_FILTER macro into:
SK_RUN_FILTER to be used with 'struct sk_filter *' and
BPF_PROG_RUN to be used with 'struct bpf_prog *'
__sk_filter_release(struct sk_filter *) gains
__bpf_prog_release(struct bpf_prog *) helper function
also perform related renames for the functions that work
with 'struct bpf_prog *', since they're on the same lines:
sk_filter_size -> bpf_prog_size
sk_filter_select_runtime -> bpf_prog_select_runtime
sk_filter_free -> bpf_prog_free
sk_unattached_filter_create -> bpf_prog_create
sk_unattached_filter_destroy -> bpf_prog_destroy
sk_store_orig_filter -> bpf_prog_store_orig_filter
sk_release_orig_filter -> bpf_release_orig_filter
__sk_migrate_filter -> bpf_migrate_filter
__sk_prepare_filter -> bpf_prepare_filter
API for attaching classic BPF to a socket stays the same:
sk_attach_filter(prog, struct sock *)/sk_detach_filter(struct sock *)
and SK_RUN_FILTER(struct sk_filter *, ctx) to execute a program
which is used by sockets, tun, af_packet
API for 'unattached' BPF programs becomes:
bpf_prog_create(struct bpf_prog **)/bpf_prog_destroy(struct bpf_prog *)
and BPF_PROG_RUN(struct bpf_prog *, ctx) to execute a program
which is used by isdn, ppp, team, seccomp, ptp, xt_bpf, cls_bpf, test_bpf
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-30 21:34:16 -06:00
|
|
|
__bpf_prog_release(fp->prog);
|
|
|
|
kfree(fp);
|
net: filter: don't release unattached filter through call_rcu()
sk_unattached_filter_destroy() does not always need to release the
filter object via rcu. Since this filter is never attached to the
socket, the caller should be responsible for releasing the filter
in a safe way, which may not necessarily imply rcu.
This is a short summary of clients of this function:
1) xt_bpf.c and cls_bpf.c use the bpf matchers from rules, these rules
are removed from the packet path before the filter is released. Thus,
the framework makes sure the filter is safely removed.
2) In the ppp driver, the ppp_lock ensures serialization between the
xmit and filter attachment/detachment path. This doesn't use rcu
so deferred release via rcu makes no sense.
3) In the isdn/ppp driver, it is called from isdn_ppp_release()
the isdn_ppp_ioctl(). This driver uses mutex and spinlocks, no rcu.
Thus, deferred rcu makes no sense to me either, the deferred releases
may be just masking the effects of wrong locking strategy, which
should be fixed in the driver itself.
4) In the team driver, this is the only place where the rcu
synchronization with unattached filter is used. Therefore, this
patch introduces synchronize_rcu() which is called from the
genetlink path to make sure the filter doesn't go away while packets
are still walking over it. I think we can revisit this once struct
bpf_prog (that only wraps specific bpf code bits) is in place, then
add some specific struct rcu_head in the scope of the team driver if
Jiri thinks this is needed.
Deferred rcu release for unattached filters was originally introduced
in 302d663 ("filter: Allow to create sk-unattached filters").
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-29 09:36:28 -06:00
|
|
|
}
|
|
|
|
|
2007-10-17 22:22:42 -06:00
|
|
|
/**
|
2010-12-06 10:29:43 -07:00
|
|
|
* sk_filter_release_rcu - Release a socket filter by rcu_head
|
2007-10-17 22:22:42 -06:00
|
|
|
* @rcu: rcu_head that contains the sk_filter to free
|
|
|
|
*/
|
2014-03-28 11:58:20 -06:00
|
|
|
static void sk_filter_release_rcu(struct rcu_head *rcu)
|
2007-10-17 22:22:42 -06:00
|
|
|
{
|
|
|
|
struct sk_filter *fp = container_of(rcu, struct sk_filter, rcu);
|
|
|
|
|
net: filter: don't release unattached filter through call_rcu()
sk_unattached_filter_destroy() does not always need to release the
filter object via rcu. Since this filter is never attached to the
socket, the caller should be responsible for releasing the filter
in a safe way, which may not necessarily imply rcu.
This is a short summary of clients of this function:
1) xt_bpf.c and cls_bpf.c use the bpf matchers from rules, these rules
are removed from the packet path before the filter is released. Thus,
the framework makes sure the filter is safely removed.
2) In the ppp driver, the ppp_lock ensures serialization between the
xmit and filter attachment/detachment path. This doesn't use rcu
so deferred release via rcu makes no sense.
3) In the isdn/ppp driver, it is called from isdn_ppp_release()
the isdn_ppp_ioctl(). This driver uses mutex and spinlocks, no rcu.
Thus, deferred rcu makes no sense to me either, the deferred releases
may be just masking the effects of wrong locking strategy, which
should be fixed in the driver itself.
4) In the team driver, this is the only place where the rcu
synchronization with unattached filter is used. Therefore, this
patch introduces synchronize_rcu() which is called from the
genetlink path to make sure the filter doesn't go away while packets
are still walking over it. I think we can revisit this once struct
bpf_prog (that only wraps specific bpf code bits) is in place, then
add some specific struct rcu_head in the scope of the team driver if
Jiri thinks this is needed.
Deferred rcu release for unattached filters was originally introduced
in 302d663 ("filter: Allow to create sk-unattached filters").
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-29 09:36:28 -06:00
|
|
|
__sk_filter_release(fp);
|
2007-10-17 22:22:42 -06:00
|
|
|
}
|
2014-03-28 11:58:20 -06:00
|
|
|
|
|
|
|
/**
|
|
|
|
* sk_filter_release - release a socket filter
|
|
|
|
* @fp: filter to remove
|
|
|
|
*
|
|
|
|
* Remove a filter from a socket and release its resources.
|
|
|
|
*/
|
|
|
|
static void sk_filter_release(struct sk_filter *fp)
|
|
|
|
{
|
|
|
|
if (atomic_dec_and_test(&fp->refcnt))
|
|
|
|
call_rcu(&fp->rcu, sk_filter_release_rcu);
|
|
|
|
}
|
|
|
|
|
|
|
|
void sk_filter_uncharge(struct sock *sk, struct sk_filter *fp)
|
|
|
|
{
|
net: filter: split 'struct sk_filter' into socket and bpf parts
clean up names related to socket filtering and bpf in the following way:
- everything that deals with sockets keeps 'sk_*' prefix
- everything that is pure BPF is changed to 'bpf_*' prefix
split 'struct sk_filter' into
struct sk_filter {
atomic_t refcnt;
struct rcu_head rcu;
struct bpf_prog *prog;
};
and
struct bpf_prog {
u32 jited:1,
len:31;
struct sock_fprog_kern *orig_prog;
unsigned int (*bpf_func)(const struct sk_buff *skb,
const struct bpf_insn *filter);
union {
struct sock_filter insns[0];
struct bpf_insn insnsi[0];
struct work_struct work;
};
};
so that 'struct bpf_prog' can be used independent of sockets and cleans up
'unattached' bpf use cases
split SK_RUN_FILTER macro into:
SK_RUN_FILTER to be used with 'struct sk_filter *' and
BPF_PROG_RUN to be used with 'struct bpf_prog *'
__sk_filter_release(struct sk_filter *) gains
__bpf_prog_release(struct bpf_prog *) helper function
also perform related renames for the functions that work
with 'struct bpf_prog *', since they're on the same lines:
sk_filter_size -> bpf_prog_size
sk_filter_select_runtime -> bpf_prog_select_runtime
sk_filter_free -> bpf_prog_free
sk_unattached_filter_create -> bpf_prog_create
sk_unattached_filter_destroy -> bpf_prog_destroy
sk_store_orig_filter -> bpf_prog_store_orig_filter
sk_release_orig_filter -> bpf_release_orig_filter
__sk_migrate_filter -> bpf_migrate_filter
__sk_prepare_filter -> bpf_prepare_filter
API for attaching classic BPF to a socket stays the same:
sk_attach_filter(prog, struct sock *)/sk_detach_filter(struct sock *)
and SK_RUN_FILTER(struct sk_filter *, ctx) to execute a program
which is used by sockets, tun, af_packet
API for 'unattached' BPF programs becomes:
bpf_prog_create(struct bpf_prog **)/bpf_prog_destroy(struct bpf_prog *)
and BPF_PROG_RUN(struct bpf_prog *, ctx) to execute a program
which is used by isdn, ppp, team, seccomp, ptp, xt_bpf, cls_bpf, test_bpf
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-30 21:34:16 -06:00
|
|
|
u32 filter_size = bpf_prog_size(fp->prog->len);
|
2014-03-28 11:58:20 -06:00
|
|
|
|
2014-07-30 21:34:12 -06:00
|
|
|
atomic_sub(filter_size, &sk->sk_omem_alloc);
|
|
|
|
sk_filter_release(fp);
|
2014-03-28 11:58:20 -06:00
|
|
|
}
|
2007-10-17 22:22:42 -06:00
|
|
|
|
2014-07-30 21:34:12 -06:00
|
|
|
/* try to charge the socket memory if there is space available
|
|
|
|
* return true on success
|
|
|
|
*/
|
|
|
|
bool sk_filter_charge(struct sock *sk, struct sk_filter *fp)
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
{
|
net: filter: split 'struct sk_filter' into socket and bpf parts
clean up names related to socket filtering and bpf in the following way:
- everything that deals with sockets keeps 'sk_*' prefix
- everything that is pure BPF is changed to 'bpf_*' prefix
split 'struct sk_filter' into
struct sk_filter {
atomic_t refcnt;
struct rcu_head rcu;
struct bpf_prog *prog;
};
and
struct bpf_prog {
u32 jited:1,
len:31;
struct sock_fprog_kern *orig_prog;
unsigned int (*bpf_func)(const struct sk_buff *skb,
const struct bpf_insn *filter);
union {
struct sock_filter insns[0];
struct bpf_insn insnsi[0];
struct work_struct work;
};
};
so that 'struct bpf_prog' can be used independent of sockets and cleans up
'unattached' bpf use cases
split SK_RUN_FILTER macro into:
SK_RUN_FILTER to be used with 'struct sk_filter *' and
BPF_PROG_RUN to be used with 'struct bpf_prog *'
__sk_filter_release(struct sk_filter *) gains
__bpf_prog_release(struct bpf_prog *) helper function
also perform related renames for the functions that work
with 'struct bpf_prog *', since they're on the same lines:
sk_filter_size -> bpf_prog_size
sk_filter_select_runtime -> bpf_prog_select_runtime
sk_filter_free -> bpf_prog_free
sk_unattached_filter_create -> bpf_prog_create
sk_unattached_filter_destroy -> bpf_prog_destroy
sk_store_orig_filter -> bpf_prog_store_orig_filter
sk_release_orig_filter -> bpf_release_orig_filter
__sk_migrate_filter -> bpf_migrate_filter
__sk_prepare_filter -> bpf_prepare_filter
API for attaching classic BPF to a socket stays the same:
sk_attach_filter(prog, struct sock *)/sk_detach_filter(struct sock *)
and SK_RUN_FILTER(struct sk_filter *, ctx) to execute a program
which is used by sockets, tun, af_packet
API for 'unattached' BPF programs becomes:
bpf_prog_create(struct bpf_prog **)/bpf_prog_destroy(struct bpf_prog *)
and BPF_PROG_RUN(struct bpf_prog *, ctx) to execute a program
which is used by isdn, ppp, team, seccomp, ptp, xt_bpf, cls_bpf, test_bpf
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-30 21:34:16 -06:00
|
|
|
u32 filter_size = bpf_prog_size(fp->prog->len);
|
2014-07-30 21:34:12 -06:00
|
|
|
|
|
|
|
/* same check as in sock_kmalloc() */
|
|
|
|
if (filter_size <= sysctl_optmem_max &&
|
|
|
|
atomic_read(&sk->sk_omem_alloc) + filter_size < sysctl_optmem_max) {
|
|
|
|
atomic_inc(&fp->refcnt);
|
|
|
|
atomic_add(filter_size, &sk->sk_omem_alloc);
|
|
|
|
return true;
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
}
|
2014-07-30 21:34:12 -06:00
|
|
|
return false;
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
}
|
|
|
|
|
net: filter: split 'struct sk_filter' into socket and bpf parts
clean up names related to socket filtering and bpf in the following way:
- everything that deals with sockets keeps 'sk_*' prefix
- everything that is pure BPF is changed to 'bpf_*' prefix
split 'struct sk_filter' into
struct sk_filter {
atomic_t refcnt;
struct rcu_head rcu;
struct bpf_prog *prog;
};
and
struct bpf_prog {
u32 jited:1,
len:31;
struct sock_fprog_kern *orig_prog;
unsigned int (*bpf_func)(const struct sk_buff *skb,
const struct bpf_insn *filter);
union {
struct sock_filter insns[0];
struct bpf_insn insnsi[0];
struct work_struct work;
};
};
so that 'struct bpf_prog' can be used independent of sockets and cleans up
'unattached' bpf use cases
split SK_RUN_FILTER macro into:
SK_RUN_FILTER to be used with 'struct sk_filter *' and
BPF_PROG_RUN to be used with 'struct bpf_prog *'
__sk_filter_release(struct sk_filter *) gains
__bpf_prog_release(struct bpf_prog *) helper function
also perform related renames for the functions that work
with 'struct bpf_prog *', since they're on the same lines:
sk_filter_size -> bpf_prog_size
sk_filter_select_runtime -> bpf_prog_select_runtime
sk_filter_free -> bpf_prog_free
sk_unattached_filter_create -> bpf_prog_create
sk_unattached_filter_destroy -> bpf_prog_destroy
sk_store_orig_filter -> bpf_prog_store_orig_filter
sk_release_orig_filter -> bpf_release_orig_filter
__sk_migrate_filter -> bpf_migrate_filter
__sk_prepare_filter -> bpf_prepare_filter
API for attaching classic BPF to a socket stays the same:
sk_attach_filter(prog, struct sock *)/sk_detach_filter(struct sock *)
and SK_RUN_FILTER(struct sk_filter *, ctx) to execute a program
which is used by sockets, tun, af_packet
API for 'unattached' BPF programs becomes:
bpf_prog_create(struct bpf_prog **)/bpf_prog_destroy(struct bpf_prog *)
and BPF_PROG_RUN(struct bpf_prog *, ctx) to execute a program
which is used by isdn, ppp, team, seccomp, ptp, xt_bpf, cls_bpf, test_bpf
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-30 21:34:16 -06:00
|
|
|
static struct bpf_prog *bpf_migrate_filter(struct bpf_prog *fp)
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
{
|
|
|
|
struct sock_filter *old_prog;
|
net: filter: split 'struct sk_filter' into socket and bpf parts
clean up names related to socket filtering and bpf in the following way:
- everything that deals with sockets keeps 'sk_*' prefix
- everything that is pure BPF is changed to 'bpf_*' prefix
split 'struct sk_filter' into
struct sk_filter {
atomic_t refcnt;
struct rcu_head rcu;
struct bpf_prog *prog;
};
and
struct bpf_prog {
u32 jited:1,
len:31;
struct sock_fprog_kern *orig_prog;
unsigned int (*bpf_func)(const struct sk_buff *skb,
const struct bpf_insn *filter);
union {
struct sock_filter insns[0];
struct bpf_insn insnsi[0];
struct work_struct work;
};
};
so that 'struct bpf_prog' can be used independent of sockets and cleans up
'unattached' bpf use cases
split SK_RUN_FILTER macro into:
SK_RUN_FILTER to be used with 'struct sk_filter *' and
BPF_PROG_RUN to be used with 'struct bpf_prog *'
__sk_filter_release(struct sk_filter *) gains
__bpf_prog_release(struct bpf_prog *) helper function
also perform related renames for the functions that work
with 'struct bpf_prog *', since they're on the same lines:
sk_filter_size -> bpf_prog_size
sk_filter_select_runtime -> bpf_prog_select_runtime
sk_filter_free -> bpf_prog_free
sk_unattached_filter_create -> bpf_prog_create
sk_unattached_filter_destroy -> bpf_prog_destroy
sk_store_orig_filter -> bpf_prog_store_orig_filter
sk_release_orig_filter -> bpf_release_orig_filter
__sk_migrate_filter -> bpf_migrate_filter
__sk_prepare_filter -> bpf_prepare_filter
API for attaching classic BPF to a socket stays the same:
sk_attach_filter(prog, struct sock *)/sk_detach_filter(struct sock *)
and SK_RUN_FILTER(struct sk_filter *, ctx) to execute a program
which is used by sockets, tun, af_packet
API for 'unattached' BPF programs becomes:
bpf_prog_create(struct bpf_prog **)/bpf_prog_destroy(struct bpf_prog *)
and BPF_PROG_RUN(struct bpf_prog *, ctx) to execute a program
which is used by isdn, ppp, team, seccomp, ptp, xt_bpf, cls_bpf, test_bpf
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-30 21:34:16 -06:00
|
|
|
struct bpf_prog *old_fp;
|
net: filter: get rid of BPF_S_* enum
This patch finally allows us to get rid of the BPF_S_* enum.
Currently, the code performs unnecessary encode and decode
workarounds in seccomp and filter migration itself when a filter
is being attached in order to overcome BPF_S_* encoding which
is not used anymore by the new interpreter resp. JIT compilers.
Keeping it around would mean that also in future we would need
to extend and maintain this enum and related encoders/decoders.
We can get rid of all that and save us these operations during
filter attaching. Naturally, also JIT compilers need to be updated
by this.
Before JIT conversion is being done, each compiler checks if A
is being loaded at startup to obtain information if it needs to
emit instructions to clear A first. Since BPF extensions are a
subset of BPF_LD | BPF_{W,H,B} | BPF_ABS variants, case statements
for extensions can be removed at that point. To ease and minimalize
code changes in the classic JITs, we have introduced bpf_anc_helper().
Tested with test_bpf on x86_64 (JIT, int), s390x (JIT, int),
arm (JIT, int), i368 (int), ppc64 (JIT, int); for sparc we
unfortunately didn't have access, but changes are analogous to
the rest.
Joint work with Alexei Starovoitov.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Mircea Gherzan <mgherzan@gmail.com>
Cc: Kees Cook <keescook@chromium.org>
Acked-by: Chema Gonzalez <chemag@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-29 02:22:50 -06:00
|
|
|
int err, new_len, old_len = fp->len;
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
|
|
|
|
/* We are free to overwrite insns et al right here as it
|
|
|
|
* won't be used at this point in time anymore internally
|
|
|
|
* after the migration to the internal BPF instruction
|
|
|
|
* representation.
|
|
|
|
*/
|
|
|
|
BUILD_BUG_ON(sizeof(struct sock_filter) !=
|
2014-07-24 17:38:21 -06:00
|
|
|
sizeof(struct bpf_insn));
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
|
|
|
|
/* Conversion cannot happen on overlapping memory areas,
|
|
|
|
* so we need to keep the user BPF around until the 2nd
|
|
|
|
* pass. At this time, the user BPF is stored in fp->insns.
|
|
|
|
*/
|
|
|
|
old_prog = kmemdup(fp->insns, old_len * sizeof(struct sock_filter),
|
2015-05-06 08:12:29 -06:00
|
|
|
GFP_KERNEL | __GFP_NOWARN);
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
if (!old_prog) {
|
|
|
|
err = -ENOMEM;
|
|
|
|
goto out_err;
|
|
|
|
}
|
|
|
|
|
|
|
|
/* 1st pass: calculate the new program length. */
|
2014-07-30 21:34:15 -06:00
|
|
|
err = bpf_convert_filter(old_prog, old_len, NULL, &new_len);
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
if (err)
|
|
|
|
goto out_err_free;
|
|
|
|
|
|
|
|
/* Expand fp for appending the new filter representation. */
|
|
|
|
old_fp = fp;
|
2014-09-02 14:53:44 -06:00
|
|
|
fp = bpf_prog_realloc(old_fp, bpf_prog_size(new_len), 0);
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
if (!fp) {
|
|
|
|
/* The old_fp is still around in case we couldn't
|
|
|
|
* allocate new memory, so uncharge on that one.
|
|
|
|
*/
|
|
|
|
fp = old_fp;
|
|
|
|
err = -ENOMEM;
|
|
|
|
goto out_err_free;
|
|
|
|
}
|
|
|
|
|
|
|
|
fp->len = new_len;
|
|
|
|
|
2014-07-24 17:38:21 -06:00
|
|
|
/* 2nd pass: remap sock_filter insns into bpf_insn insns. */
|
2014-07-30 21:34:15 -06:00
|
|
|
err = bpf_convert_filter(old_prog, old_len, fp->insnsi, &new_len);
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
if (err)
|
2014-07-30 21:34:15 -06:00
|
|
|
/* 2nd bpf_convert_filter() can fail only if it fails
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
* to allocate memory, remapping must succeed. Note,
|
|
|
|
* that at this time old_fp has already been released
|
2014-07-30 21:34:12 -06:00
|
|
|
* by krealloc().
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
*/
|
|
|
|
goto out_err_free;
|
|
|
|
|
2016-05-13 11:08:31 -06:00
|
|
|
/* We are guaranteed to never error here with cBPF to eBPF
|
|
|
|
* transitions, since there's no issue with type compatibility
|
|
|
|
* checks on program arrays.
|
|
|
|
*/
|
|
|
|
fp = bpf_prog_select_runtime(fp, &err);
|
net: filter: cleanup invocation of internal BPF
Kernel API for classic BPF socket filters is:
sk_unattached_filter_create() - validate classic BPF, convert, JIT
SK_RUN_FILTER() - run it
sk_unattached_filter_destroy() - destroy socket filter
Cleanup internal BPF kernel API as following:
sk_filter_select_runtime() - final step of internal BPF creation.
Try to JIT internal BPF program, if JIT is not available select interpreter
SK_RUN_FILTER() - run it
sk_filter_free() - free internal BPF program
Disallow direct calls to BPF interpreter. Execution of the BPF program should
be done with SK_RUN_FILTER() macro.
Example of internal BPF create, run, destroy:
struct sk_filter *fp;
fp = kzalloc(sk_filter_size(prog_len), GFP_KERNEL);
memcpy(fp->insni, prog, prog_len * sizeof(fp->insni[0]));
fp->len = prog_len;
sk_filter_select_runtime(fp);
SK_RUN_FILTER(fp, ctx);
sk_filter_free(fp);
Sockets, seccomp, testsuite, tracing are using different ways to populate
sk_filter, so first steps of program creation are not common.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-19 15:56:14 -06:00
|
|
|
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
kfree(old_prog);
|
|
|
|
return fp;
|
|
|
|
|
|
|
|
out_err_free:
|
|
|
|
kfree(old_prog);
|
|
|
|
out_err:
|
net: filter: split 'struct sk_filter' into socket and bpf parts
clean up names related to socket filtering and bpf in the following way:
- everything that deals with sockets keeps 'sk_*' prefix
- everything that is pure BPF is changed to 'bpf_*' prefix
split 'struct sk_filter' into
struct sk_filter {
atomic_t refcnt;
struct rcu_head rcu;
struct bpf_prog *prog;
};
and
struct bpf_prog {
u32 jited:1,
len:31;
struct sock_fprog_kern *orig_prog;
unsigned int (*bpf_func)(const struct sk_buff *skb,
const struct bpf_insn *filter);
union {
struct sock_filter insns[0];
struct bpf_insn insnsi[0];
struct work_struct work;
};
};
so that 'struct bpf_prog' can be used independent of sockets and cleans up
'unattached' bpf use cases
split SK_RUN_FILTER macro into:
SK_RUN_FILTER to be used with 'struct sk_filter *' and
BPF_PROG_RUN to be used with 'struct bpf_prog *'
__sk_filter_release(struct sk_filter *) gains
__bpf_prog_release(struct bpf_prog *) helper function
also perform related renames for the functions that work
with 'struct bpf_prog *', since they're on the same lines:
sk_filter_size -> bpf_prog_size
sk_filter_select_runtime -> bpf_prog_select_runtime
sk_filter_free -> bpf_prog_free
sk_unattached_filter_create -> bpf_prog_create
sk_unattached_filter_destroy -> bpf_prog_destroy
sk_store_orig_filter -> bpf_prog_store_orig_filter
sk_release_orig_filter -> bpf_release_orig_filter
__sk_migrate_filter -> bpf_migrate_filter
__sk_prepare_filter -> bpf_prepare_filter
API for attaching classic BPF to a socket stays the same:
sk_attach_filter(prog, struct sock *)/sk_detach_filter(struct sock *)
and SK_RUN_FILTER(struct sk_filter *, ctx) to execute a program
which is used by sockets, tun, af_packet
API for 'unattached' BPF programs becomes:
bpf_prog_create(struct bpf_prog **)/bpf_prog_destroy(struct bpf_prog *)
and BPF_PROG_RUN(struct bpf_prog *, ctx) to execute a program
which is used by isdn, ppp, team, seccomp, ptp, xt_bpf, cls_bpf, test_bpf
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-30 21:34:16 -06:00
|
|
|
__bpf_prog_release(fp);
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
return ERR_PTR(err);
|
|
|
|
}
|
|
|
|
|
2015-05-06 08:12:30 -06:00
|
|
|
static struct bpf_prog *bpf_prepare_filter(struct bpf_prog *fp,
|
|
|
|
bpf_aux_classic_check_t trans)
|
2012-03-31 05:01:19 -06:00
|
|
|
{
|
|
|
|
int err;
|
|
|
|
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
fp->bpf_func = NULL;
|
2015-09-29 17:41:50 -06:00
|
|
|
fp->jited = 0;
|
2012-03-31 05:01:19 -06:00
|
|
|
|
2014-07-30 21:34:14 -06:00
|
|
|
err = bpf_check_classic(fp->insns, fp->len);
|
2014-05-31 23:37:25 -06:00
|
|
|
if (err) {
|
net: filter: split 'struct sk_filter' into socket and bpf parts
clean up names related to socket filtering and bpf in the following way:
- everything that deals with sockets keeps 'sk_*' prefix
- everything that is pure BPF is changed to 'bpf_*' prefix
split 'struct sk_filter' into
struct sk_filter {
atomic_t refcnt;
struct rcu_head rcu;
struct bpf_prog *prog;
};
and
struct bpf_prog {
u32 jited:1,
len:31;
struct sock_fprog_kern *orig_prog;
unsigned int (*bpf_func)(const struct sk_buff *skb,
const struct bpf_insn *filter);
union {
struct sock_filter insns[0];
struct bpf_insn insnsi[0];
struct work_struct work;
};
};
so that 'struct bpf_prog' can be used independent of sockets and cleans up
'unattached' bpf use cases
split SK_RUN_FILTER macro into:
SK_RUN_FILTER to be used with 'struct sk_filter *' and
BPF_PROG_RUN to be used with 'struct bpf_prog *'
__sk_filter_release(struct sk_filter *) gains
__bpf_prog_release(struct bpf_prog *) helper function
also perform related renames for the functions that work
with 'struct bpf_prog *', since they're on the same lines:
sk_filter_size -> bpf_prog_size
sk_filter_select_runtime -> bpf_prog_select_runtime
sk_filter_free -> bpf_prog_free
sk_unattached_filter_create -> bpf_prog_create
sk_unattached_filter_destroy -> bpf_prog_destroy
sk_store_orig_filter -> bpf_prog_store_orig_filter
sk_release_orig_filter -> bpf_release_orig_filter
__sk_migrate_filter -> bpf_migrate_filter
__sk_prepare_filter -> bpf_prepare_filter
API for attaching classic BPF to a socket stays the same:
sk_attach_filter(prog, struct sock *)/sk_detach_filter(struct sock *)
and SK_RUN_FILTER(struct sk_filter *, ctx) to execute a program
which is used by sockets, tun, af_packet
API for 'unattached' BPF programs becomes:
bpf_prog_create(struct bpf_prog **)/bpf_prog_destroy(struct bpf_prog *)
and BPF_PROG_RUN(struct bpf_prog *, ctx) to execute a program
which is used by isdn, ppp, team, seccomp, ptp, xt_bpf, cls_bpf, test_bpf
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-30 21:34:16 -06:00
|
|
|
__bpf_prog_release(fp);
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
return ERR_PTR(err);
|
2014-05-31 23:37:25 -06:00
|
|
|
}
|
2012-03-31 05:01:19 -06:00
|
|
|
|
2015-05-06 08:12:27 -06:00
|
|
|
/* There might be additional checks and transformations
|
|
|
|
* needed on classic filters, f.e. in case of seccomp.
|
|
|
|
*/
|
|
|
|
if (trans) {
|
|
|
|
err = trans(fp->insns, fp->len);
|
|
|
|
if (err) {
|
|
|
|
__bpf_prog_release(fp);
|
|
|
|
return ERR_PTR(err);
|
|
|
|
}
|
|
|
|
}
|
|
|
|
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
/* Probe if we can JIT compile the filter and if so, do
|
|
|
|
* the compilation of the filter.
|
|
|
|
*/
|
2012-03-31 05:01:19 -06:00
|
|
|
bpf_jit_compile(fp);
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
|
|
|
|
/* JIT compiler couldn't process this filter, so do the
|
|
|
|
* internal BPF translation for the optimized interpreter.
|
|
|
|
*/
|
net: filter: cleanup invocation of internal BPF
Kernel API for classic BPF socket filters is:
sk_unattached_filter_create() - validate classic BPF, convert, JIT
SK_RUN_FILTER() - run it
sk_unattached_filter_destroy() - destroy socket filter
Cleanup internal BPF kernel API as following:
sk_filter_select_runtime() - final step of internal BPF creation.
Try to JIT internal BPF program, if JIT is not available select interpreter
SK_RUN_FILTER() - run it
sk_filter_free() - free internal BPF program
Disallow direct calls to BPF interpreter. Execution of the BPF program should
be done with SK_RUN_FILTER() macro.
Example of internal BPF create, run, destroy:
struct sk_filter *fp;
fp = kzalloc(sk_filter_size(prog_len), GFP_KERNEL);
memcpy(fp->insni, prog, prog_len * sizeof(fp->insni[0]));
fp->len = prog_len;
sk_filter_select_runtime(fp);
SK_RUN_FILTER(fp, ctx);
sk_filter_free(fp);
Sockets, seccomp, testsuite, tracing are using different ways to populate
sk_filter, so first steps of program creation are not common.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-19 15:56:14 -06:00
|
|
|
if (!fp->jited)
|
net: filter: split 'struct sk_filter' into socket and bpf parts
clean up names related to socket filtering and bpf in the following way:
- everything that deals with sockets keeps 'sk_*' prefix
- everything that is pure BPF is changed to 'bpf_*' prefix
split 'struct sk_filter' into
struct sk_filter {
atomic_t refcnt;
struct rcu_head rcu;
struct bpf_prog *prog;
};
and
struct bpf_prog {
u32 jited:1,
len:31;
struct sock_fprog_kern *orig_prog;
unsigned int (*bpf_func)(const struct sk_buff *skb,
const struct bpf_insn *filter);
union {
struct sock_filter insns[0];
struct bpf_insn insnsi[0];
struct work_struct work;
};
};
so that 'struct bpf_prog' can be used independent of sockets and cleans up
'unattached' bpf use cases
split SK_RUN_FILTER macro into:
SK_RUN_FILTER to be used with 'struct sk_filter *' and
BPF_PROG_RUN to be used with 'struct bpf_prog *'
__sk_filter_release(struct sk_filter *) gains
__bpf_prog_release(struct bpf_prog *) helper function
also perform related renames for the functions that work
with 'struct bpf_prog *', since they're on the same lines:
sk_filter_size -> bpf_prog_size
sk_filter_select_runtime -> bpf_prog_select_runtime
sk_filter_free -> bpf_prog_free
sk_unattached_filter_create -> bpf_prog_create
sk_unattached_filter_destroy -> bpf_prog_destroy
sk_store_orig_filter -> bpf_prog_store_orig_filter
sk_release_orig_filter -> bpf_release_orig_filter
__sk_migrate_filter -> bpf_migrate_filter
__sk_prepare_filter -> bpf_prepare_filter
API for attaching classic BPF to a socket stays the same:
sk_attach_filter(prog, struct sock *)/sk_detach_filter(struct sock *)
and SK_RUN_FILTER(struct sk_filter *, ctx) to execute a program
which is used by sockets, tun, af_packet
API for 'unattached' BPF programs becomes:
bpf_prog_create(struct bpf_prog **)/bpf_prog_destroy(struct bpf_prog *)
and BPF_PROG_RUN(struct bpf_prog *, ctx) to execute a program
which is used by isdn, ppp, team, seccomp, ptp, xt_bpf, cls_bpf, test_bpf
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-30 21:34:16 -06:00
|
|
|
fp = bpf_migrate_filter(fp);
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
|
|
|
|
return fp;
|
2012-03-31 05:01:19 -06:00
|
|
|
}
|
|
|
|
|
|
|
|
/**
|
net: filter: split 'struct sk_filter' into socket and bpf parts
clean up names related to socket filtering and bpf in the following way:
- everything that deals with sockets keeps 'sk_*' prefix
- everything that is pure BPF is changed to 'bpf_*' prefix
split 'struct sk_filter' into
struct sk_filter {
atomic_t refcnt;
struct rcu_head rcu;
struct bpf_prog *prog;
};
and
struct bpf_prog {
u32 jited:1,
len:31;
struct sock_fprog_kern *orig_prog;
unsigned int (*bpf_func)(const struct sk_buff *skb,
const struct bpf_insn *filter);
union {
struct sock_filter insns[0];
struct bpf_insn insnsi[0];
struct work_struct work;
};
};
so that 'struct bpf_prog' can be used independent of sockets and cleans up
'unattached' bpf use cases
split SK_RUN_FILTER macro into:
SK_RUN_FILTER to be used with 'struct sk_filter *' and
BPF_PROG_RUN to be used with 'struct bpf_prog *'
__sk_filter_release(struct sk_filter *) gains
__bpf_prog_release(struct bpf_prog *) helper function
also perform related renames for the functions that work
with 'struct bpf_prog *', since they're on the same lines:
sk_filter_size -> bpf_prog_size
sk_filter_select_runtime -> bpf_prog_select_runtime
sk_filter_free -> bpf_prog_free
sk_unattached_filter_create -> bpf_prog_create
sk_unattached_filter_destroy -> bpf_prog_destroy
sk_store_orig_filter -> bpf_prog_store_orig_filter
sk_release_orig_filter -> bpf_release_orig_filter
__sk_migrate_filter -> bpf_migrate_filter
__sk_prepare_filter -> bpf_prepare_filter
API for attaching classic BPF to a socket stays the same:
sk_attach_filter(prog, struct sock *)/sk_detach_filter(struct sock *)
and SK_RUN_FILTER(struct sk_filter *, ctx) to execute a program
which is used by sockets, tun, af_packet
API for 'unattached' BPF programs becomes:
bpf_prog_create(struct bpf_prog **)/bpf_prog_destroy(struct bpf_prog *)
and BPF_PROG_RUN(struct bpf_prog *, ctx) to execute a program
which is used by isdn, ppp, team, seccomp, ptp, xt_bpf, cls_bpf, test_bpf
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-30 21:34:16 -06:00
|
|
|
* bpf_prog_create - create an unattached filter
|
2012-06-08 08:01:44 -06:00
|
|
|
* @pfp: the unattached filter that is created
|
2014-06-24 07:33:21 -06:00
|
|
|
* @fprog: the filter program
|
2012-03-31 05:01:19 -06:00
|
|
|
*
|
2012-06-08 08:01:44 -06:00
|
|
|
* Create a filter independent of any socket. We first run some
|
2012-03-31 05:01:19 -06:00
|
|
|
* sanity checks on it to make sure it does not explode on us later.
|
|
|
|
* If an error occurs or there is insufficient memory for the filter
|
|
|
|
* a negative errno code is returned. On success the return is zero.
|
|
|
|
*/
|
net: filter: split 'struct sk_filter' into socket and bpf parts
clean up names related to socket filtering and bpf in the following way:
- everything that deals with sockets keeps 'sk_*' prefix
- everything that is pure BPF is changed to 'bpf_*' prefix
split 'struct sk_filter' into
struct sk_filter {
atomic_t refcnt;
struct rcu_head rcu;
struct bpf_prog *prog;
};
and
struct bpf_prog {
u32 jited:1,
len:31;
struct sock_fprog_kern *orig_prog;
unsigned int (*bpf_func)(const struct sk_buff *skb,
const struct bpf_insn *filter);
union {
struct sock_filter insns[0];
struct bpf_insn insnsi[0];
struct work_struct work;
};
};
so that 'struct bpf_prog' can be used independent of sockets and cleans up
'unattached' bpf use cases
split SK_RUN_FILTER macro into:
SK_RUN_FILTER to be used with 'struct sk_filter *' and
BPF_PROG_RUN to be used with 'struct bpf_prog *'
__sk_filter_release(struct sk_filter *) gains
__bpf_prog_release(struct bpf_prog *) helper function
also perform related renames for the functions that work
with 'struct bpf_prog *', since they're on the same lines:
sk_filter_size -> bpf_prog_size
sk_filter_select_runtime -> bpf_prog_select_runtime
sk_filter_free -> bpf_prog_free
sk_unattached_filter_create -> bpf_prog_create
sk_unattached_filter_destroy -> bpf_prog_destroy
sk_store_orig_filter -> bpf_prog_store_orig_filter
sk_release_orig_filter -> bpf_release_orig_filter
__sk_migrate_filter -> bpf_migrate_filter
__sk_prepare_filter -> bpf_prepare_filter
API for attaching classic BPF to a socket stays the same:
sk_attach_filter(prog, struct sock *)/sk_detach_filter(struct sock *)
and SK_RUN_FILTER(struct sk_filter *, ctx) to execute a program
which is used by sockets, tun, af_packet
API for 'unattached' BPF programs becomes:
bpf_prog_create(struct bpf_prog **)/bpf_prog_destroy(struct bpf_prog *)
and BPF_PROG_RUN(struct bpf_prog *, ctx) to execute a program
which is used by isdn, ppp, team, seccomp, ptp, xt_bpf, cls_bpf, test_bpf
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-30 21:34:16 -06:00
|
|
|
int bpf_prog_create(struct bpf_prog **pfp, struct sock_fprog_kern *fprog)
|
2012-03-31 05:01:19 -06:00
|
|
|
{
|
2014-07-30 21:34:13 -06:00
|
|
|
unsigned int fsize = bpf_classic_proglen(fprog);
|
net: filter: split 'struct sk_filter' into socket and bpf parts
clean up names related to socket filtering and bpf in the following way:
- everything that deals with sockets keeps 'sk_*' prefix
- everything that is pure BPF is changed to 'bpf_*' prefix
split 'struct sk_filter' into
struct sk_filter {
atomic_t refcnt;
struct rcu_head rcu;
struct bpf_prog *prog;
};
and
struct bpf_prog {
u32 jited:1,
len:31;
struct sock_fprog_kern *orig_prog;
unsigned int (*bpf_func)(const struct sk_buff *skb,
const struct bpf_insn *filter);
union {
struct sock_filter insns[0];
struct bpf_insn insnsi[0];
struct work_struct work;
};
};
so that 'struct bpf_prog' can be used independent of sockets and cleans up
'unattached' bpf use cases
split SK_RUN_FILTER macro into:
SK_RUN_FILTER to be used with 'struct sk_filter *' and
BPF_PROG_RUN to be used with 'struct bpf_prog *'
__sk_filter_release(struct sk_filter *) gains
__bpf_prog_release(struct bpf_prog *) helper function
also perform related renames for the functions that work
with 'struct bpf_prog *', since they're on the same lines:
sk_filter_size -> bpf_prog_size
sk_filter_select_runtime -> bpf_prog_select_runtime
sk_filter_free -> bpf_prog_free
sk_unattached_filter_create -> bpf_prog_create
sk_unattached_filter_destroy -> bpf_prog_destroy
sk_store_orig_filter -> bpf_prog_store_orig_filter
sk_release_orig_filter -> bpf_release_orig_filter
__sk_migrate_filter -> bpf_migrate_filter
__sk_prepare_filter -> bpf_prepare_filter
API for attaching classic BPF to a socket stays the same:
sk_attach_filter(prog, struct sock *)/sk_detach_filter(struct sock *)
and SK_RUN_FILTER(struct sk_filter *, ctx) to execute a program
which is used by sockets, tun, af_packet
API for 'unattached' BPF programs becomes:
bpf_prog_create(struct bpf_prog **)/bpf_prog_destroy(struct bpf_prog *)
and BPF_PROG_RUN(struct bpf_prog *, ctx) to execute a program
which is used by isdn, ppp, team, seccomp, ptp, xt_bpf, cls_bpf, test_bpf
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-30 21:34:16 -06:00
|
|
|
struct bpf_prog *fp;
|
2012-03-31 05:01:19 -06:00
|
|
|
|
|
|
|
/* Make sure new filter is there and in the right amounts. */
|
|
|
|
if (fprog->filter == NULL)
|
|
|
|
return -EINVAL;
|
|
|
|
|
2014-09-02 14:53:44 -06:00
|
|
|
fp = bpf_prog_alloc(bpf_prog_size(fprog->len), 0);
|
2012-03-31 05:01:19 -06:00
|
|
|
if (!fp)
|
|
|
|
return -ENOMEM;
|
net: filter: keep original BPF program around
In order to open up the possibility to internally transform a BPF program
into an alternative and possibly non-trivial reversible representation, we
need to keep the original BPF program around, so that it can be passed back
to user space w/o the need of a complex decoder.
The reason for that use case resides in commit a8fc92778080 ("sk-filter:
Add ability to get socket filter program (v2)"), that is, the ability
to retrieve the currently attached BPF filter from a given socket used
mainly by the checkpoint-restore project, for example.
Therefore, we add two helpers sk_{store,release}_orig_filter for taking
care of that. In the sk_unattached_filter_create() case, there's no such
possibility/requirement to retrieve a loaded BPF program. Therefore, we
can spare us the work in that case.
This approach will simplify and slightly speed up both, sk_get_filter()
and sock_diag_put_filterinfo() handlers as we won't need to successively
decode filters anymore through sk_decode_filter(). As we still need
sk_decode_filter() later on, we're keeping it around.
Joint work with Alexei Starovoitov.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:19 -06:00
|
|
|
|
2012-03-31 05:01:19 -06:00
|
|
|
memcpy(fp->insns, fprog->filter, fsize);
|
|
|
|
|
|
|
|
fp->len = fprog->len;
|
net: filter: keep original BPF program around
In order to open up the possibility to internally transform a BPF program
into an alternative and possibly non-trivial reversible representation, we
need to keep the original BPF program around, so that it can be passed back
to user space w/o the need of a complex decoder.
The reason for that use case resides in commit a8fc92778080 ("sk-filter:
Add ability to get socket filter program (v2)"), that is, the ability
to retrieve the currently attached BPF filter from a given socket used
mainly by the checkpoint-restore project, for example.
Therefore, we add two helpers sk_{store,release}_orig_filter for taking
care of that. In the sk_unattached_filter_create() case, there's no such
possibility/requirement to retrieve a loaded BPF program. Therefore, we
can spare us the work in that case.
This approach will simplify and slightly speed up both, sk_get_filter()
and sock_diag_put_filterinfo() handlers as we won't need to successively
decode filters anymore through sk_decode_filter(). As we still need
sk_decode_filter() later on, we're keeping it around.
Joint work with Alexei Starovoitov.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:19 -06:00
|
|
|
/* Since unattached filters are not copied back to user
|
|
|
|
* space through sk_get_filter(), we do not need to hold
|
|
|
|
* a copy here, and can spare us the work.
|
|
|
|
*/
|
|
|
|
fp->orig_prog = NULL;
|
2012-03-31 05:01:19 -06:00
|
|
|
|
net: filter: split 'struct sk_filter' into socket and bpf parts
clean up names related to socket filtering and bpf in the following way:
- everything that deals with sockets keeps 'sk_*' prefix
- everything that is pure BPF is changed to 'bpf_*' prefix
split 'struct sk_filter' into
struct sk_filter {
atomic_t refcnt;
struct rcu_head rcu;
struct bpf_prog *prog;
};
and
struct bpf_prog {
u32 jited:1,
len:31;
struct sock_fprog_kern *orig_prog;
unsigned int (*bpf_func)(const struct sk_buff *skb,
const struct bpf_insn *filter);
union {
struct sock_filter insns[0];
struct bpf_insn insnsi[0];
struct work_struct work;
};
};
so that 'struct bpf_prog' can be used independent of sockets and cleans up
'unattached' bpf use cases
split SK_RUN_FILTER macro into:
SK_RUN_FILTER to be used with 'struct sk_filter *' and
BPF_PROG_RUN to be used with 'struct bpf_prog *'
__sk_filter_release(struct sk_filter *) gains
__bpf_prog_release(struct bpf_prog *) helper function
also perform related renames for the functions that work
with 'struct bpf_prog *', since they're on the same lines:
sk_filter_size -> bpf_prog_size
sk_filter_select_runtime -> bpf_prog_select_runtime
sk_filter_free -> bpf_prog_free
sk_unattached_filter_create -> bpf_prog_create
sk_unattached_filter_destroy -> bpf_prog_destroy
sk_store_orig_filter -> bpf_prog_store_orig_filter
sk_release_orig_filter -> bpf_release_orig_filter
__sk_migrate_filter -> bpf_migrate_filter
__sk_prepare_filter -> bpf_prepare_filter
API for attaching classic BPF to a socket stays the same:
sk_attach_filter(prog, struct sock *)/sk_detach_filter(struct sock *)
and SK_RUN_FILTER(struct sk_filter *, ctx) to execute a program
which is used by sockets, tun, af_packet
API for 'unattached' BPF programs becomes:
bpf_prog_create(struct bpf_prog **)/bpf_prog_destroy(struct bpf_prog *)
and BPF_PROG_RUN(struct bpf_prog *, ctx) to execute a program
which is used by isdn, ppp, team, seccomp, ptp, xt_bpf, cls_bpf, test_bpf
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-30 21:34:16 -06:00
|
|
|
/* bpf_prepare_filter() already takes care of freeing
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
* memory in case something goes wrong.
|
|
|
|
*/
|
2015-05-06 08:12:27 -06:00
|
|
|
fp = bpf_prepare_filter(fp, NULL);
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
if (IS_ERR(fp))
|
|
|
|
return PTR_ERR(fp);
|
2012-03-31 05:01:19 -06:00
|
|
|
|
|
|
|
*pfp = fp;
|
|
|
|
return 0;
|
|
|
|
}
|
net: filter: split 'struct sk_filter' into socket and bpf parts
clean up names related to socket filtering and bpf in the following way:
- everything that deals with sockets keeps 'sk_*' prefix
- everything that is pure BPF is changed to 'bpf_*' prefix
split 'struct sk_filter' into
struct sk_filter {
atomic_t refcnt;
struct rcu_head rcu;
struct bpf_prog *prog;
};
and
struct bpf_prog {
u32 jited:1,
len:31;
struct sock_fprog_kern *orig_prog;
unsigned int (*bpf_func)(const struct sk_buff *skb,
const struct bpf_insn *filter);
union {
struct sock_filter insns[0];
struct bpf_insn insnsi[0];
struct work_struct work;
};
};
so that 'struct bpf_prog' can be used independent of sockets and cleans up
'unattached' bpf use cases
split SK_RUN_FILTER macro into:
SK_RUN_FILTER to be used with 'struct sk_filter *' and
BPF_PROG_RUN to be used with 'struct bpf_prog *'
__sk_filter_release(struct sk_filter *) gains
__bpf_prog_release(struct bpf_prog *) helper function
also perform related renames for the functions that work
with 'struct bpf_prog *', since they're on the same lines:
sk_filter_size -> bpf_prog_size
sk_filter_select_runtime -> bpf_prog_select_runtime
sk_filter_free -> bpf_prog_free
sk_unattached_filter_create -> bpf_prog_create
sk_unattached_filter_destroy -> bpf_prog_destroy
sk_store_orig_filter -> bpf_prog_store_orig_filter
sk_release_orig_filter -> bpf_release_orig_filter
__sk_migrate_filter -> bpf_migrate_filter
__sk_prepare_filter -> bpf_prepare_filter
API for attaching classic BPF to a socket stays the same:
sk_attach_filter(prog, struct sock *)/sk_detach_filter(struct sock *)
and SK_RUN_FILTER(struct sk_filter *, ctx) to execute a program
which is used by sockets, tun, af_packet
API for 'unattached' BPF programs becomes:
bpf_prog_create(struct bpf_prog **)/bpf_prog_destroy(struct bpf_prog *)
and BPF_PROG_RUN(struct bpf_prog *, ctx) to execute a program
which is used by isdn, ppp, team, seccomp, ptp, xt_bpf, cls_bpf, test_bpf
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-30 21:34:16 -06:00
|
|
|
EXPORT_SYMBOL_GPL(bpf_prog_create);
|
2012-03-31 05:01:19 -06:00
|
|
|
|
2015-05-06 08:12:30 -06:00
|
|
|
/**
|
|
|
|
* bpf_prog_create_from_user - create an unattached filter from user buffer
|
|
|
|
* @pfp: the unattached filter that is created
|
|
|
|
* @fprog: the filter program
|
|
|
|
* @trans: post-classic verifier transformation handler
|
2015-10-02 07:17:33 -06:00
|
|
|
* @save_orig: save classic BPF program
|
2015-05-06 08:12:30 -06:00
|
|
|
*
|
|
|
|
* This function effectively does the same as bpf_prog_create(), only
|
|
|
|
* that it builds up its insns buffer from user space provided buffer.
|
|
|
|
* It also allows for passing a bpf_aux_classic_check_t handler.
|
|
|
|
*/
|
|
|
|
int bpf_prog_create_from_user(struct bpf_prog **pfp, struct sock_fprog *fprog,
|
2015-10-02 07:17:33 -06:00
|
|
|
bpf_aux_classic_check_t trans, bool save_orig)
|
2015-05-06 08:12:30 -06:00
|
|
|
{
|
|
|
|
unsigned int fsize = bpf_classic_proglen(fprog);
|
|
|
|
struct bpf_prog *fp;
|
2015-10-02 07:17:33 -06:00
|
|
|
int err;
|
2015-05-06 08:12:30 -06:00
|
|
|
|
|
|
|
/* Make sure new filter is there and in the right amounts. */
|
|
|
|
if (fprog->filter == NULL)
|
|
|
|
return -EINVAL;
|
|
|
|
|
|
|
|
fp = bpf_prog_alloc(bpf_prog_size(fprog->len), 0);
|
|
|
|
if (!fp)
|
|
|
|
return -ENOMEM;
|
|
|
|
|
|
|
|
if (copy_from_user(fp->insns, fprog->filter, fsize)) {
|
|
|
|
__bpf_prog_free(fp);
|
|
|
|
return -EFAULT;
|
|
|
|
}
|
|
|
|
|
|
|
|
fp->len = fprog->len;
|
|
|
|
fp->orig_prog = NULL;
|
|
|
|
|
2015-10-02 07:17:33 -06:00
|
|
|
if (save_orig) {
|
|
|
|
err = bpf_prog_store_orig_filter(fp, fprog);
|
|
|
|
if (err) {
|
|
|
|
__bpf_prog_free(fp);
|
|
|
|
return -ENOMEM;
|
|
|
|
}
|
|
|
|
}
|
|
|
|
|
2015-05-06 08:12:30 -06:00
|
|
|
/* bpf_prepare_filter() already takes care of freeing
|
|
|
|
* memory in case something goes wrong.
|
|
|
|
*/
|
|
|
|
fp = bpf_prepare_filter(fp, trans);
|
|
|
|
if (IS_ERR(fp))
|
|
|
|
return PTR_ERR(fp);
|
|
|
|
|
|
|
|
*pfp = fp;
|
|
|
|
return 0;
|
|
|
|
}
|
2015-08-17 15:37:06 -06:00
|
|
|
EXPORT_SYMBOL_GPL(bpf_prog_create_from_user);
|
2015-05-06 08:12:30 -06:00
|
|
|
|
net: filter: split 'struct sk_filter' into socket and bpf parts
clean up names related to socket filtering and bpf in the following way:
- everything that deals with sockets keeps 'sk_*' prefix
- everything that is pure BPF is changed to 'bpf_*' prefix
split 'struct sk_filter' into
struct sk_filter {
atomic_t refcnt;
struct rcu_head rcu;
struct bpf_prog *prog;
};
and
struct bpf_prog {
u32 jited:1,
len:31;
struct sock_fprog_kern *orig_prog;
unsigned int (*bpf_func)(const struct sk_buff *skb,
const struct bpf_insn *filter);
union {
struct sock_filter insns[0];
struct bpf_insn insnsi[0];
struct work_struct work;
};
};
so that 'struct bpf_prog' can be used independent of sockets and cleans up
'unattached' bpf use cases
split SK_RUN_FILTER macro into:
SK_RUN_FILTER to be used with 'struct sk_filter *' and
BPF_PROG_RUN to be used with 'struct bpf_prog *'
__sk_filter_release(struct sk_filter *) gains
__bpf_prog_release(struct bpf_prog *) helper function
also perform related renames for the functions that work
with 'struct bpf_prog *', since they're on the same lines:
sk_filter_size -> bpf_prog_size
sk_filter_select_runtime -> bpf_prog_select_runtime
sk_filter_free -> bpf_prog_free
sk_unattached_filter_create -> bpf_prog_create
sk_unattached_filter_destroy -> bpf_prog_destroy
sk_store_orig_filter -> bpf_prog_store_orig_filter
sk_release_orig_filter -> bpf_release_orig_filter
__sk_migrate_filter -> bpf_migrate_filter
__sk_prepare_filter -> bpf_prepare_filter
API for attaching classic BPF to a socket stays the same:
sk_attach_filter(prog, struct sock *)/sk_detach_filter(struct sock *)
and SK_RUN_FILTER(struct sk_filter *, ctx) to execute a program
which is used by sockets, tun, af_packet
API for 'unattached' BPF programs becomes:
bpf_prog_create(struct bpf_prog **)/bpf_prog_destroy(struct bpf_prog *)
and BPF_PROG_RUN(struct bpf_prog *, ctx) to execute a program
which is used by isdn, ppp, team, seccomp, ptp, xt_bpf, cls_bpf, test_bpf
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-30 21:34:16 -06:00
|
|
|
void bpf_prog_destroy(struct bpf_prog *fp)
|
2012-03-31 05:01:19 -06:00
|
|
|
{
|
net: filter: split 'struct sk_filter' into socket and bpf parts
clean up names related to socket filtering and bpf in the following way:
- everything that deals with sockets keeps 'sk_*' prefix
- everything that is pure BPF is changed to 'bpf_*' prefix
split 'struct sk_filter' into
struct sk_filter {
atomic_t refcnt;
struct rcu_head rcu;
struct bpf_prog *prog;
};
and
struct bpf_prog {
u32 jited:1,
len:31;
struct sock_fprog_kern *orig_prog;
unsigned int (*bpf_func)(const struct sk_buff *skb,
const struct bpf_insn *filter);
union {
struct sock_filter insns[0];
struct bpf_insn insnsi[0];
struct work_struct work;
};
};
so that 'struct bpf_prog' can be used independent of sockets and cleans up
'unattached' bpf use cases
split SK_RUN_FILTER macro into:
SK_RUN_FILTER to be used with 'struct sk_filter *' and
BPF_PROG_RUN to be used with 'struct bpf_prog *'
__sk_filter_release(struct sk_filter *) gains
__bpf_prog_release(struct bpf_prog *) helper function
also perform related renames for the functions that work
with 'struct bpf_prog *', since they're on the same lines:
sk_filter_size -> bpf_prog_size
sk_filter_select_runtime -> bpf_prog_select_runtime
sk_filter_free -> bpf_prog_free
sk_unattached_filter_create -> bpf_prog_create
sk_unattached_filter_destroy -> bpf_prog_destroy
sk_store_orig_filter -> bpf_prog_store_orig_filter
sk_release_orig_filter -> bpf_release_orig_filter
__sk_migrate_filter -> bpf_migrate_filter
__sk_prepare_filter -> bpf_prepare_filter
API for attaching classic BPF to a socket stays the same:
sk_attach_filter(prog, struct sock *)/sk_detach_filter(struct sock *)
and SK_RUN_FILTER(struct sk_filter *, ctx) to execute a program
which is used by sockets, tun, af_packet
API for 'unattached' BPF programs becomes:
bpf_prog_create(struct bpf_prog **)/bpf_prog_destroy(struct bpf_prog *)
and BPF_PROG_RUN(struct bpf_prog *, ctx) to execute a program
which is used by isdn, ppp, team, seccomp, ptp, xt_bpf, cls_bpf, test_bpf
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-30 21:34:16 -06:00
|
|
|
__bpf_prog_release(fp);
|
2012-03-31 05:01:19 -06:00
|
|
|
}
|
net: filter: split 'struct sk_filter' into socket and bpf parts
clean up names related to socket filtering and bpf in the following way:
- everything that deals with sockets keeps 'sk_*' prefix
- everything that is pure BPF is changed to 'bpf_*' prefix
split 'struct sk_filter' into
struct sk_filter {
atomic_t refcnt;
struct rcu_head rcu;
struct bpf_prog *prog;
};
and
struct bpf_prog {
u32 jited:1,
len:31;
struct sock_fprog_kern *orig_prog;
unsigned int (*bpf_func)(const struct sk_buff *skb,
const struct bpf_insn *filter);
union {
struct sock_filter insns[0];
struct bpf_insn insnsi[0];
struct work_struct work;
};
};
so that 'struct bpf_prog' can be used independent of sockets and cleans up
'unattached' bpf use cases
split SK_RUN_FILTER macro into:
SK_RUN_FILTER to be used with 'struct sk_filter *' and
BPF_PROG_RUN to be used with 'struct bpf_prog *'
__sk_filter_release(struct sk_filter *) gains
__bpf_prog_release(struct bpf_prog *) helper function
also perform related renames for the functions that work
with 'struct bpf_prog *', since they're on the same lines:
sk_filter_size -> bpf_prog_size
sk_filter_select_runtime -> bpf_prog_select_runtime
sk_filter_free -> bpf_prog_free
sk_unattached_filter_create -> bpf_prog_create
sk_unattached_filter_destroy -> bpf_prog_destroy
sk_store_orig_filter -> bpf_prog_store_orig_filter
sk_release_orig_filter -> bpf_release_orig_filter
__sk_migrate_filter -> bpf_migrate_filter
__sk_prepare_filter -> bpf_prepare_filter
API for attaching classic BPF to a socket stays the same:
sk_attach_filter(prog, struct sock *)/sk_detach_filter(struct sock *)
and SK_RUN_FILTER(struct sk_filter *, ctx) to execute a program
which is used by sockets, tun, af_packet
API for 'unattached' BPF programs becomes:
bpf_prog_create(struct bpf_prog **)/bpf_prog_destroy(struct bpf_prog *)
and BPF_PROG_RUN(struct bpf_prog *, ctx) to execute a program
which is used by isdn, ppp, team, seccomp, ptp, xt_bpf, cls_bpf, test_bpf
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-30 21:34:16 -06:00
|
|
|
EXPORT_SYMBOL_GPL(bpf_prog_destroy);
|
2012-03-31 05:01:19 -06:00
|
|
|
|
2016-04-05 09:10:16 -06:00
|
|
|
static int __sk_attach_prog(struct bpf_prog *prog, struct sock *sk)
|
2015-03-02 04:25:51 -07:00
|
|
|
{
|
|
|
|
struct sk_filter *fp, *old_fp;
|
|
|
|
|
|
|
|
fp = kmalloc(sizeof(*fp), GFP_KERNEL);
|
|
|
|
if (!fp)
|
|
|
|
return -ENOMEM;
|
|
|
|
|
|
|
|
fp->prog = prog;
|
|
|
|
atomic_set(&fp->refcnt, 0);
|
|
|
|
|
|
|
|
if (!sk_filter_charge(sk, fp)) {
|
|
|
|
kfree(fp);
|
|
|
|
return -ENOMEM;
|
|
|
|
}
|
|
|
|
|
2016-04-05 09:10:16 -06:00
|
|
|
old_fp = rcu_dereference_protected(sk->sk_filter,
|
|
|
|
lockdep_sock_is_held(sk));
|
2015-03-02 04:25:51 -07:00
|
|
|
rcu_assign_pointer(sk->sk_filter, fp);
|
2016-04-05 09:10:16 -06:00
|
|
|
|
2015-03-02 04:25:51 -07:00
|
|
|
if (old_fp)
|
|
|
|
sk_filter_uncharge(sk, old_fp);
|
|
|
|
|
|
|
|
return 0;
|
|
|
|
}
|
|
|
|
|
2016-01-04 15:41:47 -07:00
|
|
|
static int __reuseport_attach_prog(struct bpf_prog *prog, struct sock *sk)
|
|
|
|
{
|
|
|
|
struct bpf_prog *old_prog;
|
|
|
|
int err;
|
|
|
|
|
|
|
|
if (bpf_prog_size(prog->len) > sysctl_optmem_max)
|
|
|
|
return -ENOMEM;
|
|
|
|
|
2016-02-10 09:50:39 -07:00
|
|
|
if (sk_unhashed(sk) && sk->sk_reuseport) {
|
2016-01-04 15:41:47 -07:00
|
|
|
err = reuseport_alloc(sk);
|
|
|
|
if (err)
|
|
|
|
return err;
|
|
|
|
} else if (!rcu_access_pointer(sk->sk_reuseport_cb)) {
|
|
|
|
/* The socket wasn't bound with SO_REUSEPORT */
|
|
|
|
return -EINVAL;
|
|
|
|
}
|
|
|
|
|
|
|
|
old_prog = reuseport_attach_prog(sk, prog);
|
|
|
|
if (old_prog)
|
|
|
|
bpf_prog_destroy(old_prog);
|
|
|
|
|
|
|
|
return 0;
|
|
|
|
}
|
|
|
|
|
|
|
|
static
|
|
|
|
struct bpf_prog *__get_filter(struct sock_fprog *fprog, struct sock *sk)
|
2005-04-16 16:20:36 -06:00
|
|
|
{
|
2014-07-30 21:34:13 -06:00
|
|
|
unsigned int fsize = bpf_classic_proglen(fprog);
|
net: filter: split 'struct sk_filter' into socket and bpf parts
clean up names related to socket filtering and bpf in the following way:
- everything that deals with sockets keeps 'sk_*' prefix
- everything that is pure BPF is changed to 'bpf_*' prefix
split 'struct sk_filter' into
struct sk_filter {
atomic_t refcnt;
struct rcu_head rcu;
struct bpf_prog *prog;
};
and
struct bpf_prog {
u32 jited:1,
len:31;
struct sock_fprog_kern *orig_prog;
unsigned int (*bpf_func)(const struct sk_buff *skb,
const struct bpf_insn *filter);
union {
struct sock_filter insns[0];
struct bpf_insn insnsi[0];
struct work_struct work;
};
};
so that 'struct bpf_prog' can be used independent of sockets and cleans up
'unattached' bpf use cases
split SK_RUN_FILTER macro into:
SK_RUN_FILTER to be used with 'struct sk_filter *' and
BPF_PROG_RUN to be used with 'struct bpf_prog *'
__sk_filter_release(struct sk_filter *) gains
__bpf_prog_release(struct bpf_prog *) helper function
also perform related renames for the functions that work
with 'struct bpf_prog *', since they're on the same lines:
sk_filter_size -> bpf_prog_size
sk_filter_select_runtime -> bpf_prog_select_runtime
sk_filter_free -> bpf_prog_free
sk_unattached_filter_create -> bpf_prog_create
sk_unattached_filter_destroy -> bpf_prog_destroy
sk_store_orig_filter -> bpf_prog_store_orig_filter
sk_release_orig_filter -> bpf_release_orig_filter
__sk_migrate_filter -> bpf_migrate_filter
__sk_prepare_filter -> bpf_prepare_filter
API for attaching classic BPF to a socket stays the same:
sk_attach_filter(prog, struct sock *)/sk_detach_filter(struct sock *)
and SK_RUN_FILTER(struct sk_filter *, ctx) to execute a program
which is used by sockets, tun, af_packet
API for 'unattached' BPF programs becomes:
bpf_prog_create(struct bpf_prog **)/bpf_prog_destroy(struct bpf_prog *)
and BPF_PROG_RUN(struct bpf_prog *, ctx) to execute a program
which is used by isdn, ppp, team, seccomp, ptp, xt_bpf, cls_bpf, test_bpf
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-30 21:34:16 -06:00
|
|
|
unsigned int bpf_fsize = bpf_prog_size(fprog->len);
|
|
|
|
struct bpf_prog *prog;
|
2005-04-16 16:20:36 -06:00
|
|
|
int err;
|
|
|
|
|
2013-01-16 14:55:49 -07:00
|
|
|
if (sock_flag(sk, SOCK_FILTER_LOCKED))
|
2016-01-04 15:41:47 -07:00
|
|
|
return ERR_PTR(-EPERM);
|
2013-01-16 14:55:49 -07:00
|
|
|
|
2005-04-16 16:20:36 -06:00
|
|
|
/* Make sure new filter is there and in the right amounts. */
|
2006-01-17 03:25:52 -07:00
|
|
|
if (fprog->filter == NULL)
|
2016-01-04 15:41:47 -07:00
|
|
|
return ERR_PTR(-EINVAL);
|
2005-04-16 16:20:36 -06:00
|
|
|
|
2014-09-02 14:53:44 -06:00
|
|
|
prog = bpf_prog_alloc(bpf_fsize, 0);
|
net: filter: split 'struct sk_filter' into socket and bpf parts
clean up names related to socket filtering and bpf in the following way:
- everything that deals with sockets keeps 'sk_*' prefix
- everything that is pure BPF is changed to 'bpf_*' prefix
split 'struct sk_filter' into
struct sk_filter {
atomic_t refcnt;
struct rcu_head rcu;
struct bpf_prog *prog;
};
and
struct bpf_prog {
u32 jited:1,
len:31;
struct sock_fprog_kern *orig_prog;
unsigned int (*bpf_func)(const struct sk_buff *skb,
const struct bpf_insn *filter);
union {
struct sock_filter insns[0];
struct bpf_insn insnsi[0];
struct work_struct work;
};
};
so that 'struct bpf_prog' can be used independent of sockets and cleans up
'unattached' bpf use cases
split SK_RUN_FILTER macro into:
SK_RUN_FILTER to be used with 'struct sk_filter *' and
BPF_PROG_RUN to be used with 'struct bpf_prog *'
__sk_filter_release(struct sk_filter *) gains
__bpf_prog_release(struct bpf_prog *) helper function
also perform related renames for the functions that work
with 'struct bpf_prog *', since they're on the same lines:
sk_filter_size -> bpf_prog_size
sk_filter_select_runtime -> bpf_prog_select_runtime
sk_filter_free -> bpf_prog_free
sk_unattached_filter_create -> bpf_prog_create
sk_unattached_filter_destroy -> bpf_prog_destroy
sk_store_orig_filter -> bpf_prog_store_orig_filter
sk_release_orig_filter -> bpf_release_orig_filter
__sk_migrate_filter -> bpf_migrate_filter
__sk_prepare_filter -> bpf_prepare_filter
API for attaching classic BPF to a socket stays the same:
sk_attach_filter(prog, struct sock *)/sk_detach_filter(struct sock *)
and SK_RUN_FILTER(struct sk_filter *, ctx) to execute a program
which is used by sockets, tun, af_packet
API for 'unattached' BPF programs becomes:
bpf_prog_create(struct bpf_prog **)/bpf_prog_destroy(struct bpf_prog *)
and BPF_PROG_RUN(struct bpf_prog *, ctx) to execute a program
which is used by isdn, ppp, team, seccomp, ptp, xt_bpf, cls_bpf, test_bpf
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-30 21:34:16 -06:00
|
|
|
if (!prog)
|
2016-01-04 15:41:47 -07:00
|
|
|
return ERR_PTR(-ENOMEM);
|
net: filter: keep original BPF program around
In order to open up the possibility to internally transform a BPF program
into an alternative and possibly non-trivial reversible representation, we
need to keep the original BPF program around, so that it can be passed back
to user space w/o the need of a complex decoder.
The reason for that use case resides in commit a8fc92778080 ("sk-filter:
Add ability to get socket filter program (v2)"), that is, the ability
to retrieve the currently attached BPF filter from a given socket used
mainly by the checkpoint-restore project, for example.
Therefore, we add two helpers sk_{store,release}_orig_filter for taking
care of that. In the sk_unattached_filter_create() case, there's no such
possibility/requirement to retrieve a loaded BPF program. Therefore, we
can spare us the work in that case.
This approach will simplify and slightly speed up both, sk_get_filter()
and sock_diag_put_filterinfo() handlers as we won't need to successively
decode filters anymore through sk_decode_filter(). As we still need
sk_decode_filter() later on, we're keeping it around.
Joint work with Alexei Starovoitov.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:19 -06:00
|
|
|
|
net: filter: split 'struct sk_filter' into socket and bpf parts
clean up names related to socket filtering and bpf in the following way:
- everything that deals with sockets keeps 'sk_*' prefix
- everything that is pure BPF is changed to 'bpf_*' prefix
split 'struct sk_filter' into
struct sk_filter {
atomic_t refcnt;
struct rcu_head rcu;
struct bpf_prog *prog;
};
and
struct bpf_prog {
u32 jited:1,
len:31;
struct sock_fprog_kern *orig_prog;
unsigned int (*bpf_func)(const struct sk_buff *skb,
const struct bpf_insn *filter);
union {
struct sock_filter insns[0];
struct bpf_insn insnsi[0];
struct work_struct work;
};
};
so that 'struct bpf_prog' can be used independent of sockets and cleans up
'unattached' bpf use cases
split SK_RUN_FILTER macro into:
SK_RUN_FILTER to be used with 'struct sk_filter *' and
BPF_PROG_RUN to be used with 'struct bpf_prog *'
__sk_filter_release(struct sk_filter *) gains
__bpf_prog_release(struct bpf_prog *) helper function
also perform related renames for the functions that work
with 'struct bpf_prog *', since they're on the same lines:
sk_filter_size -> bpf_prog_size
sk_filter_select_runtime -> bpf_prog_select_runtime
sk_filter_free -> bpf_prog_free
sk_unattached_filter_create -> bpf_prog_create
sk_unattached_filter_destroy -> bpf_prog_destroy
sk_store_orig_filter -> bpf_prog_store_orig_filter
sk_release_orig_filter -> bpf_release_orig_filter
__sk_migrate_filter -> bpf_migrate_filter
__sk_prepare_filter -> bpf_prepare_filter
API for attaching classic BPF to a socket stays the same:
sk_attach_filter(prog, struct sock *)/sk_detach_filter(struct sock *)
and SK_RUN_FILTER(struct sk_filter *, ctx) to execute a program
which is used by sockets, tun, af_packet
API for 'unattached' BPF programs becomes:
bpf_prog_create(struct bpf_prog **)/bpf_prog_destroy(struct bpf_prog *)
and BPF_PROG_RUN(struct bpf_prog *, ctx) to execute a program
which is used by isdn, ppp, team, seccomp, ptp, xt_bpf, cls_bpf, test_bpf
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-30 21:34:16 -06:00
|
|
|
if (copy_from_user(prog->insns, fprog->filter, fsize)) {
|
2014-09-12 22:06:30 -06:00
|
|
|
__bpf_prog_free(prog);
|
2016-01-04 15:41:47 -07:00
|
|
|
return ERR_PTR(-EFAULT);
|
2005-04-16 16:20:36 -06:00
|
|
|
}
|
|
|
|
|
net: filter: split 'struct sk_filter' into socket and bpf parts
clean up names related to socket filtering and bpf in the following way:
- everything that deals with sockets keeps 'sk_*' prefix
- everything that is pure BPF is changed to 'bpf_*' prefix
split 'struct sk_filter' into
struct sk_filter {
atomic_t refcnt;
struct rcu_head rcu;
struct bpf_prog *prog;
};
and
struct bpf_prog {
u32 jited:1,
len:31;
struct sock_fprog_kern *orig_prog;
unsigned int (*bpf_func)(const struct sk_buff *skb,
const struct bpf_insn *filter);
union {
struct sock_filter insns[0];
struct bpf_insn insnsi[0];
struct work_struct work;
};
};
so that 'struct bpf_prog' can be used independent of sockets and cleans up
'unattached' bpf use cases
split SK_RUN_FILTER macro into:
SK_RUN_FILTER to be used with 'struct sk_filter *' and
BPF_PROG_RUN to be used with 'struct bpf_prog *'
__sk_filter_release(struct sk_filter *) gains
__bpf_prog_release(struct bpf_prog *) helper function
also perform related renames for the functions that work
with 'struct bpf_prog *', since they're on the same lines:
sk_filter_size -> bpf_prog_size
sk_filter_select_runtime -> bpf_prog_select_runtime
sk_filter_free -> bpf_prog_free
sk_unattached_filter_create -> bpf_prog_create
sk_unattached_filter_destroy -> bpf_prog_destroy
sk_store_orig_filter -> bpf_prog_store_orig_filter
sk_release_orig_filter -> bpf_release_orig_filter
__sk_migrate_filter -> bpf_migrate_filter
__sk_prepare_filter -> bpf_prepare_filter
API for attaching classic BPF to a socket stays the same:
sk_attach_filter(prog, struct sock *)/sk_detach_filter(struct sock *)
and SK_RUN_FILTER(struct sk_filter *, ctx) to execute a program
which is used by sockets, tun, af_packet
API for 'unattached' BPF programs becomes:
bpf_prog_create(struct bpf_prog **)/bpf_prog_destroy(struct bpf_prog *)
and BPF_PROG_RUN(struct bpf_prog *, ctx) to execute a program
which is used by isdn, ppp, team, seccomp, ptp, xt_bpf, cls_bpf, test_bpf
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-30 21:34:16 -06:00
|
|
|
prog->len = fprog->len;
|
2005-04-16 16:20:36 -06:00
|
|
|
|
net: filter: split 'struct sk_filter' into socket and bpf parts
clean up names related to socket filtering and bpf in the following way:
- everything that deals with sockets keeps 'sk_*' prefix
- everything that is pure BPF is changed to 'bpf_*' prefix
split 'struct sk_filter' into
struct sk_filter {
atomic_t refcnt;
struct rcu_head rcu;
struct bpf_prog *prog;
};
and
struct bpf_prog {
u32 jited:1,
len:31;
struct sock_fprog_kern *orig_prog;
unsigned int (*bpf_func)(const struct sk_buff *skb,
const struct bpf_insn *filter);
union {
struct sock_filter insns[0];
struct bpf_insn insnsi[0];
struct work_struct work;
};
};
so that 'struct bpf_prog' can be used independent of sockets and cleans up
'unattached' bpf use cases
split SK_RUN_FILTER macro into:
SK_RUN_FILTER to be used with 'struct sk_filter *' and
BPF_PROG_RUN to be used with 'struct bpf_prog *'
__sk_filter_release(struct sk_filter *) gains
__bpf_prog_release(struct bpf_prog *) helper function
also perform related renames for the functions that work
with 'struct bpf_prog *', since they're on the same lines:
sk_filter_size -> bpf_prog_size
sk_filter_select_runtime -> bpf_prog_select_runtime
sk_filter_free -> bpf_prog_free
sk_unattached_filter_create -> bpf_prog_create
sk_unattached_filter_destroy -> bpf_prog_destroy
sk_store_orig_filter -> bpf_prog_store_orig_filter
sk_release_orig_filter -> bpf_release_orig_filter
__sk_migrate_filter -> bpf_migrate_filter
__sk_prepare_filter -> bpf_prepare_filter
API for attaching classic BPF to a socket stays the same:
sk_attach_filter(prog, struct sock *)/sk_detach_filter(struct sock *)
and SK_RUN_FILTER(struct sk_filter *, ctx) to execute a program
which is used by sockets, tun, af_packet
API for 'unattached' BPF programs becomes:
bpf_prog_create(struct bpf_prog **)/bpf_prog_destroy(struct bpf_prog *)
and BPF_PROG_RUN(struct bpf_prog *, ctx) to execute a program
which is used by isdn, ppp, team, seccomp, ptp, xt_bpf, cls_bpf, test_bpf
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-30 21:34:16 -06:00
|
|
|
err = bpf_prog_store_orig_filter(prog, fprog);
|
net: filter: keep original BPF program around
In order to open up the possibility to internally transform a BPF program
into an alternative and possibly non-trivial reversible representation, we
need to keep the original BPF program around, so that it can be passed back
to user space w/o the need of a complex decoder.
The reason for that use case resides in commit a8fc92778080 ("sk-filter:
Add ability to get socket filter program (v2)"), that is, the ability
to retrieve the currently attached BPF filter from a given socket used
mainly by the checkpoint-restore project, for example.
Therefore, we add two helpers sk_{store,release}_orig_filter for taking
care of that. In the sk_unattached_filter_create() case, there's no such
possibility/requirement to retrieve a loaded BPF program. Therefore, we
can spare us the work in that case.
This approach will simplify and slightly speed up both, sk_get_filter()
and sock_diag_put_filterinfo() handlers as we won't need to successively
decode filters anymore through sk_decode_filter(). As we still need
sk_decode_filter() later on, we're keeping it around.
Joint work with Alexei Starovoitov.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:19 -06:00
|
|
|
if (err) {
|
2014-09-12 22:06:30 -06:00
|
|
|
__bpf_prog_free(prog);
|
2016-01-04 15:41:47 -07:00
|
|
|
return ERR_PTR(-ENOMEM);
|
net: filter: keep original BPF program around
In order to open up the possibility to internally transform a BPF program
into an alternative and possibly non-trivial reversible representation, we
need to keep the original BPF program around, so that it can be passed back
to user space w/o the need of a complex decoder.
The reason for that use case resides in commit a8fc92778080 ("sk-filter:
Add ability to get socket filter program (v2)"), that is, the ability
to retrieve the currently attached BPF filter from a given socket used
mainly by the checkpoint-restore project, for example.
Therefore, we add two helpers sk_{store,release}_orig_filter for taking
care of that. In the sk_unattached_filter_create() case, there's no such
possibility/requirement to retrieve a loaded BPF program. Therefore, we
can spare us the work in that case.
This approach will simplify and slightly speed up both, sk_get_filter()
and sock_diag_put_filterinfo() handlers as we won't need to successively
decode filters anymore through sk_decode_filter(). As we still need
sk_decode_filter() later on, we're keeping it around.
Joint work with Alexei Starovoitov.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:19 -06:00
|
|
|
}
|
|
|
|
|
net: filter: split 'struct sk_filter' into socket and bpf parts
clean up names related to socket filtering and bpf in the following way:
- everything that deals with sockets keeps 'sk_*' prefix
- everything that is pure BPF is changed to 'bpf_*' prefix
split 'struct sk_filter' into
struct sk_filter {
atomic_t refcnt;
struct rcu_head rcu;
struct bpf_prog *prog;
};
and
struct bpf_prog {
u32 jited:1,
len:31;
struct sock_fprog_kern *orig_prog;
unsigned int (*bpf_func)(const struct sk_buff *skb,
const struct bpf_insn *filter);
union {
struct sock_filter insns[0];
struct bpf_insn insnsi[0];
struct work_struct work;
};
};
so that 'struct bpf_prog' can be used independent of sockets and cleans up
'unattached' bpf use cases
split SK_RUN_FILTER macro into:
SK_RUN_FILTER to be used with 'struct sk_filter *' and
BPF_PROG_RUN to be used with 'struct bpf_prog *'
__sk_filter_release(struct sk_filter *) gains
__bpf_prog_release(struct bpf_prog *) helper function
also perform related renames for the functions that work
with 'struct bpf_prog *', since they're on the same lines:
sk_filter_size -> bpf_prog_size
sk_filter_select_runtime -> bpf_prog_select_runtime
sk_filter_free -> bpf_prog_free
sk_unattached_filter_create -> bpf_prog_create
sk_unattached_filter_destroy -> bpf_prog_destroy
sk_store_orig_filter -> bpf_prog_store_orig_filter
sk_release_orig_filter -> bpf_release_orig_filter
__sk_migrate_filter -> bpf_migrate_filter
__sk_prepare_filter -> bpf_prepare_filter
API for attaching classic BPF to a socket stays the same:
sk_attach_filter(prog, struct sock *)/sk_detach_filter(struct sock *)
and SK_RUN_FILTER(struct sk_filter *, ctx) to execute a program
which is used by sockets, tun, af_packet
API for 'unattached' BPF programs becomes:
bpf_prog_create(struct bpf_prog **)/bpf_prog_destroy(struct bpf_prog *)
and BPF_PROG_RUN(struct bpf_prog *, ctx) to execute a program
which is used by isdn, ppp, team, seccomp, ptp, xt_bpf, cls_bpf, test_bpf
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-30 21:34:16 -06:00
|
|
|
/* bpf_prepare_filter() already takes care of freeing
|
net: filter: rework/optimize internal BPF interpreter's instruction set
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:25 -06:00
|
|
|
* memory in case something goes wrong.
|
|
|
|
*/
|
2016-01-04 15:41:47 -07:00
|
|
|
return bpf_prepare_filter(prog, NULL);
|
|
|
|
}
|
|
|
|
|
|
|
|
/**
|
|
|
|
* sk_attach_filter - attach a socket filter
|
|
|
|
* @fprog: the filter program
|
|
|
|
* @sk: the socket to use
|
|
|
|
*
|
|
|
|
* Attach the user's filter code. We first run some sanity checks on
|
|
|
|
* it to make sure it does not explode on us later. If an error
|
|
|
|
* occurs or there is insufficient memory for the filter a negative
|
|
|
|
* errno code is returned. On success the return is zero.
|
|
|
|
*/
|
2016-04-05 09:10:16 -06:00
|
|
|
int sk_attach_filter(struct sock_fprog *fprog, struct sock *sk)
|
2016-01-04 15:41:47 -07:00
|
|
|
{
|
|
|
|
struct bpf_prog *prog = __get_filter(fprog, sk);
|
|
|
|
int err;
|
|
|
|
|
net: filter: split 'struct sk_filter' into socket and bpf parts
clean up names related to socket filtering and bpf in the following way:
- everything that deals with sockets keeps 'sk_*' prefix
- everything that is pure BPF is changed to 'bpf_*' prefix
split 'struct sk_filter' into
struct sk_filter {
atomic_t refcnt;
struct rcu_head rcu;
struct bpf_prog *prog;
};
and
struct bpf_prog {
u32 jited:1,
len:31;
struct sock_fprog_kern *orig_prog;
unsigned int (*bpf_func)(const struct sk_buff *skb,
const struct bpf_insn *filter);
union {
struct sock_filter insns[0];
struct bpf_insn insnsi[0];
struct work_struct work;
};
};
so that 'struct bpf_prog' can be used independent of sockets and cleans up
'unattached' bpf use cases
split SK_RUN_FILTER macro into:
SK_RUN_FILTER to be used with 'struct sk_filter *' and
BPF_PROG_RUN to be used with 'struct bpf_prog *'
__sk_filter_release(struct sk_filter *) gains
__bpf_prog_release(struct bpf_prog *) helper function
also perform related renames for the functions that work
with 'struct bpf_prog *', since they're on the same lines:
sk_filter_size -> bpf_prog_size
sk_filter_select_runtime -> bpf_prog_select_runtime
sk_filter_free -> bpf_prog_free
sk_unattached_filter_create -> bpf_prog_create
sk_unattached_filter_destroy -> bpf_prog_destroy
sk_store_orig_filter -> bpf_prog_store_orig_filter
sk_release_orig_filter -> bpf_release_orig_filter
__sk_migrate_filter -> bpf_migrate_filter
__sk_prepare_filter -> bpf_prepare_filter
API for attaching classic BPF to a socket stays the same:
sk_attach_filter(prog, struct sock *)/sk_detach_filter(struct sock *)
and SK_RUN_FILTER(struct sk_filter *, ctx) to execute a program
which is used by sockets, tun, af_packet
API for 'unattached' BPF programs becomes:
bpf_prog_create(struct bpf_prog **)/bpf_prog_destroy(struct bpf_prog *)
and BPF_PROG_RUN(struct bpf_prog *, ctx) to execute a program
which is used by isdn, ppp, team, seccomp, ptp, xt_bpf, cls_bpf, test_bpf
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-30 21:34:16 -06:00
|
|
|
if (IS_ERR(prog))
|
|
|
|
return PTR_ERR(prog);
|
|
|
|
|
2016-04-05 09:10:16 -06:00
|
|
|
err = __sk_attach_prog(prog, sk);
|
2015-03-02 04:25:51 -07:00
|
|
|
if (err < 0) {
|
net: filter: split 'struct sk_filter' into socket and bpf parts
clean up names related to socket filtering and bpf in the following way:
- everything that deals with sockets keeps 'sk_*' prefix
- everything that is pure BPF is changed to 'bpf_*' prefix
split 'struct sk_filter' into
struct sk_filter {
atomic_t refcnt;
struct rcu_head rcu;
struct bpf_prog *prog;
};
and
struct bpf_prog {
u32 jited:1,
len:31;
struct sock_fprog_kern *orig_prog;
unsigned int (*bpf_func)(const struct sk_buff *skb,
const struct bpf_insn *filter);
union {
struct sock_filter insns[0];
struct bpf_insn insnsi[0];
struct work_struct work;
};
};
so that 'struct bpf_prog' can be used independent of sockets and cleans up
'unattached' bpf use cases
split SK_RUN_FILTER macro into:
SK_RUN_FILTER to be used with 'struct sk_filter *' and
BPF_PROG_RUN to be used with 'struct bpf_prog *'
__sk_filter_release(struct sk_filter *) gains
__bpf_prog_release(struct bpf_prog *) helper function
also perform related renames for the functions that work
with 'struct bpf_prog *', since they're on the same lines:
sk_filter_size -> bpf_prog_size
sk_filter_select_runtime -> bpf_prog_select_runtime
sk_filter_free -> bpf_prog_free
sk_unattached_filter_create -> bpf_prog_create
sk_unattached_filter_destroy -> bpf_prog_destroy
sk_store_orig_filter -> bpf_prog_store_orig_filter
sk_release_orig_filter -> bpf_release_orig_filter
__sk_migrate_filter -> bpf_migrate_filter
__sk_prepare_filter -> bpf_prepare_filter
API for attaching classic BPF to a socket stays the same:
sk_attach_filter(prog, struct sock *)/sk_detach_filter(struct sock *)
and SK_RUN_FILTER(struct sk_filter *, ctx) to execute a program
which is used by sockets, tun, af_packet
API for 'unattached' BPF programs becomes:
bpf_prog_create(struct bpf_prog **)/bpf_prog_destroy(struct bpf_prog *)
and BPF_PROG_RUN(struct bpf_prog *, ctx) to execute a program
which is used by isdn, ppp, team, seccomp, ptp, xt_bpf, cls_bpf, test_bpf
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-30 21:34:16 -06:00
|
|
|
__bpf_prog_release(prog);
|
2015-03-02 04:25:51 -07:00
|
|
|
return err;
|
2014-07-30 21:34:12 -06:00
|
|
|
}
|
|
|
|
|
2007-10-17 22:22:17 -06:00
|
|
|
return 0;
|
2005-04-16 16:20:36 -06:00
|
|
|
}
|
2016-04-05 09:10:16 -06:00
|
|
|
EXPORT_SYMBOL_GPL(sk_attach_filter);
|
2005-04-16 16:20:36 -06:00
|
|
|
|
2016-01-04 15:41:47 -07:00
|
|
|
int sk_reuseport_attach_filter(struct sock_fprog *fprog, struct sock *sk)
|
2014-12-01 16:06:35 -07:00
|
|
|
{
|
2016-01-04 15:41:47 -07:00
|
|
|
struct bpf_prog *prog = __get_filter(fprog, sk);
|
2015-03-02 04:25:51 -07:00
|
|
|
int err;
|
2014-12-01 16:06:35 -07:00
|
|
|
|
2016-01-04 15:41:47 -07:00
|
|
|
if (IS_ERR(prog))
|
|
|
|
return PTR_ERR(prog);
|
|
|
|
|
|
|
|
err = __reuseport_attach_prog(prog, sk);
|
|
|
|
if (err < 0) {
|
|
|
|
__bpf_prog_release(prog);
|
|
|
|
return err;
|
|
|
|
}
|
|
|
|
|
|
|
|
return 0;
|
|
|
|
}
|
|
|
|
|
|
|
|
static struct bpf_prog *__get_bpf(u32 ufd, struct sock *sk)
|
|
|
|
{
|
|
|
|
struct bpf_prog *prog;
|
|
|
|
|
2014-12-01 16:06:35 -07:00
|
|
|
if (sock_flag(sk, SOCK_FILTER_LOCKED))
|
2016-01-04 15:41:47 -07:00
|
|
|
return ERR_PTR(-EPERM);
|
2014-12-01 16:06:35 -07:00
|
|
|
|
|
|
|
prog = bpf_prog_get(ufd);
|
2014-12-10 21:14:55 -07:00
|
|
|
if (IS_ERR(prog))
|
2016-01-04 15:41:47 -07:00
|
|
|
return prog;
|
2014-12-01 16:06:35 -07:00
|
|
|
|
2015-03-01 04:31:47 -07:00
|
|
|
if (prog->type != BPF_PROG_TYPE_SOCKET_FILTER) {
|
2014-12-01 16:06:35 -07:00
|
|
|
bpf_prog_put(prog);
|
2016-01-04 15:41:47 -07:00
|
|
|
return ERR_PTR(-EINVAL);
|
2014-12-01 16:06:35 -07:00
|
|
|
}
|
|
|
|
|
2016-01-04 15:41:47 -07:00
|
|
|
return prog;
|
|
|
|
}
|
|
|
|
|
|
|
|
int sk_attach_bpf(u32 ufd, struct sock *sk)
|
|
|
|
{
|
|
|
|
struct bpf_prog *prog = __get_bpf(ufd, sk);
|
|
|
|
int err;
|
|
|
|
|
|
|
|
if (IS_ERR(prog))
|
|
|
|
return PTR_ERR(prog);
|
|
|
|
|
2016-04-05 09:10:16 -06:00
|
|
|
err = __sk_attach_prog(prog, sk);
|
2015-03-02 04:25:51 -07:00
|
|
|
if (err < 0) {
|
2014-12-01 16:06:35 -07:00
|
|
|
bpf_prog_put(prog);
|
2015-03-02 04:25:51 -07:00
|
|
|
return err;
|
2014-12-01 16:06:35 -07:00
|
|
|
}
|
|
|
|
|
|
|
|
return 0;
|
|
|
|
}
|
|
|
|
|
2016-01-04 15:41:47 -07:00
|
|
|
int sk_reuseport_attach_bpf(u32 ufd, struct sock *sk)
|
|
|
|
{
|
|
|
|
struct bpf_prog *prog = __get_bpf(ufd, sk);
|
|
|
|
int err;
|
|
|
|
|
|
|
|
if (IS_ERR(prog))
|
|
|
|
return PTR_ERR(prog);
|
|
|
|
|
|
|
|
err = __reuseport_attach_prog(prog, sk);
|
|
|
|
if (err < 0) {
|
|
|
|
bpf_prog_put(prog);
|
|
|
|
return err;
|
|
|
|
}
|
|
|
|
|
|
|
|
return 0;
|
|
|
|
}
|
|
|
|
|
2016-02-19 15:05:24 -07:00
|
|
|
struct bpf_scratchpad {
|
|
|
|
union {
|
|
|
|
__be32 diff[MAX_BPF_STACK / sizeof(__be32)];
|
|
|
|
u8 buff[MAX_BPF_STACK];
|
|
|
|
};
|
|
|
|
};
|
|
|
|
|
|
|
|
static DEFINE_PER_CPU(struct bpf_scratchpad, bpf_sp);
|
2015-04-01 18:12:13 -06:00
|
|
|
|
2016-05-05 20:49:12 -06:00
|
|
|
static inline int bpf_try_make_writable(struct sk_buff *skb,
|
|
|
|
unsigned int write_len)
|
|
|
|
{
|
|
|
|
int err;
|
|
|
|
|
|
|
|
if (!skb_cloned(skb))
|
|
|
|
return 0;
|
|
|
|
if (skb_clone_writable(skb, write_len))
|
|
|
|
return 0;
|
|
|
|
err = pskb_expand_head(skb, 0, 0, GFP_ATOMIC);
|
|
|
|
if (!err)
|
|
|
|
bpf_compute_data_end(skb);
|
|
|
|
return err;
|
|
|
|
}
|
|
|
|
|
2015-04-01 18:12:13 -06:00
|
|
|
static u64 bpf_skb_store_bytes(u64 r1, u64 r2, u64 r3, u64 r4, u64 flags)
|
2015-03-26 20:53:57 -06:00
|
|
|
{
|
2016-02-19 15:05:24 -07:00
|
|
|
struct bpf_scratchpad *sp = this_cpu_ptr(&bpf_sp);
|
2015-03-26 20:53:57 -06:00
|
|
|
struct sk_buff *skb = (struct sk_buff *) (long) r1;
|
2015-04-15 13:55:45 -06:00
|
|
|
int offset = (int) r2;
|
2015-03-26 20:53:57 -06:00
|
|
|
void *from = (void *) (long) r3;
|
|
|
|
unsigned int len = (unsigned int) r4;
|
|
|
|
void *ptr;
|
|
|
|
|
2016-03-04 07:15:03 -07:00
|
|
|
if (unlikely(flags & ~(BPF_F_RECOMPUTE_CSUM | BPF_F_INVALIDATE_HASH)))
|
2016-01-10 17:16:38 -07:00
|
|
|
return -EINVAL;
|
|
|
|
|
2015-03-26 20:53:57 -06:00
|
|
|
/* bpf verifier guarantees that:
|
|
|
|
* 'from' pointer points to bpf program stack
|
|
|
|
* 'len' bytes of it were initialized
|
|
|
|
* 'len' > 0
|
|
|
|
* 'skb' is a valid pointer to 'struct sk_buff'
|
|
|
|
*
|
|
|
|
* so check for invalid 'offset' and too large 'len'
|
|
|
|
*/
|
2016-02-19 15:05:24 -07:00
|
|
|
if (unlikely((u32) offset > 0xffff || len > sizeof(sp->buff)))
|
2015-03-26 20:53:57 -06:00
|
|
|
return -EFAULT;
|
2016-05-05 20:49:12 -06:00
|
|
|
if (unlikely(bpf_try_make_writable(skb, offset + len)))
|
2015-03-26 20:53:57 -06:00
|
|
|
return -EFAULT;
|
|
|
|
|
2016-02-19 15:05:24 -07:00
|
|
|
ptr = skb_header_pointer(skb, offset, len, sp->buff);
|
2015-03-26 20:53:57 -06:00
|
|
|
if (unlikely(!ptr))
|
|
|
|
return -EFAULT;
|
|
|
|
|
2016-01-10 17:16:38 -07:00
|
|
|
if (flags & BPF_F_RECOMPUTE_CSUM)
|
2015-04-01 18:12:13 -06:00
|
|
|
skb_postpull_rcsum(skb, ptr, len);
|
2015-03-26 20:53:57 -06:00
|
|
|
|
|
|
|
memcpy(ptr, from, len);
|
|
|
|
|
2016-02-19 15:05:24 -07:00
|
|
|
if (ptr == sp->buff)
|
2015-03-26 20:53:57 -06:00
|
|
|
/* skb_store_bits cannot return -EFAULT here */
|
|
|
|
skb_store_bits(skb, offset, ptr, len);
|
|
|
|
|
2016-01-10 17:16:38 -07:00
|
|
|
if (flags & BPF_F_RECOMPUTE_CSUM)
|
2016-01-07 07:50:23 -07:00
|
|
|
skb_postpush_rcsum(skb, ptr, len);
|
2016-03-04 07:15:03 -07:00
|
|
|
if (flags & BPF_F_INVALIDATE_HASH)
|
|
|
|
skb_clear_hash(skb);
|
2016-01-07 07:50:23 -07:00
|
|
|
|
2015-03-26 20:53:57 -06:00
|
|
|
return 0;
|
|
|
|
}
|
|
|
|
|
2016-03-04 07:15:04 -07:00
|
|
|
static const struct bpf_func_proto bpf_skb_store_bytes_proto = {
|
2015-03-26 20:53:57 -06:00
|
|
|
.func = bpf_skb_store_bytes,
|
|
|
|
.gpl_only = false,
|
|
|
|
.ret_type = RET_INTEGER,
|
|
|
|
.arg1_type = ARG_PTR_TO_CTX,
|
|
|
|
.arg2_type = ARG_ANYTHING,
|
|
|
|
.arg3_type = ARG_PTR_TO_STACK,
|
|
|
|
.arg4_type = ARG_CONST_STACK_SIZE,
|
2015-04-01 18:12:13 -06:00
|
|
|
.arg5_type = ARG_ANYTHING,
|
|
|
|
};
|
|
|
|
|
bpf: add bpf_skb_load_bytes helper
When hacking tc programs with eBPF, one of the issues that come up
from time to time is to load addresses from headers. In eBPF as in
classic BPF, we have BPF_LD | BPF_ABS | BPF_{B,H,W} instructions that
extract a byte, half-word or word out of the skb data though helpers
such as bpf_load_pointer() (interpreter case).
F.e. extracting a whole IPv6 address could possibly look like ...
union v6addr {
struct {
__u32 p1;
__u32 p2;
__u32 p3;
__u32 p4;
};
__u8 addr[16];
};
[...]
a.p1 = htonl(load_word(skb, off));
a.p2 = htonl(load_word(skb, off + 4));
a.p3 = htonl(load_word(skb, off + 8));
a.p4 = htonl(load_word(skb, off + 12));
[...]
/* access to a.addr[...] */
This work adds a complementary helper bpf_skb_load_bytes() (we also
have bpf_skb_store_bytes()) as an alternative where the same call
would look like from an eBPF program:
ret = bpf_skb_load_bytes(skb, off, addr, sizeof(addr));
Same verifier restrictions apply as in ffeedafbf023 ("bpf: introduce
current->pid, tgid, uid, gid, comm accessors") case, where stack memory
access needs to be statically verified and thus guaranteed to be
initialized in first use (otherwise verifier cannot tell whether a
subsequent access to it is valid or not as it's runtime dependent).
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-17 15:51:53 -07:00
|
|
|
static u64 bpf_skb_load_bytes(u64 r1, u64 r2, u64 r3, u64 r4, u64 r5)
|
|
|
|
{
|
|
|
|
const struct sk_buff *skb = (const struct sk_buff *)(unsigned long) r1;
|
|
|
|
int offset = (int) r2;
|
|
|
|
void *to = (void *)(unsigned long) r3;
|
|
|
|
unsigned int len = (unsigned int) r4;
|
|
|
|
void *ptr;
|
|
|
|
|
2016-04-12 16:10:52 -06:00
|
|
|
if (unlikely((u32) offset > 0xffff))
|
|
|
|
goto err_clear;
|
bpf: add bpf_skb_load_bytes helper
When hacking tc programs with eBPF, one of the issues that come up
from time to time is to load addresses from headers. In eBPF as in
classic BPF, we have BPF_LD | BPF_ABS | BPF_{B,H,W} instructions that
extract a byte, half-word or word out of the skb data though helpers
such as bpf_load_pointer() (interpreter case).
F.e. extracting a whole IPv6 address could possibly look like ...
union v6addr {
struct {
__u32 p1;
__u32 p2;
__u32 p3;
__u32 p4;
};
__u8 addr[16];
};
[...]
a.p1 = htonl(load_word(skb, off));
a.p2 = htonl(load_word(skb, off + 4));
a.p3 = htonl(load_word(skb, off + 8));
a.p4 = htonl(load_word(skb, off + 12));
[...]
/* access to a.addr[...] */
This work adds a complementary helper bpf_skb_load_bytes() (we also
have bpf_skb_store_bytes()) as an alternative where the same call
would look like from an eBPF program:
ret = bpf_skb_load_bytes(skb, off, addr, sizeof(addr));
Same verifier restrictions apply as in ffeedafbf023 ("bpf: introduce
current->pid, tgid, uid, gid, comm accessors") case, where stack memory
access needs to be statically verified and thus guaranteed to be
initialized in first use (otherwise verifier cannot tell whether a
subsequent access to it is valid or not as it's runtime dependent).
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-17 15:51:53 -07:00
|
|
|
|
|
|
|
ptr = skb_header_pointer(skb, offset, len, to);
|
|
|
|
if (unlikely(!ptr))
|
2016-04-12 16:10:52 -06:00
|
|
|
goto err_clear;
|
bpf: add bpf_skb_load_bytes helper
When hacking tc programs with eBPF, one of the issues that come up
from time to time is to load addresses from headers. In eBPF as in
classic BPF, we have BPF_LD | BPF_ABS | BPF_{B,H,W} instructions that
extract a byte, half-word or word out of the skb data though helpers
such as bpf_load_pointer() (interpreter case).
F.e. extracting a whole IPv6 address could possibly look like ...
union v6addr {
struct {
__u32 p1;
__u32 p2;
__u32 p3;
__u32 p4;
};
__u8 addr[16];
};
[...]
a.p1 = htonl(load_word(skb, off));
a.p2 = htonl(load_word(skb, off + 4));
a.p3 = htonl(load_word(skb, off + 8));
a.p4 = htonl(load_word(skb, off + 12));
[...]
/* access to a.addr[...] */
This work adds a complementary helper bpf_skb_load_bytes() (we also
have bpf_skb_store_bytes()) as an alternative where the same call
would look like from an eBPF program:
ret = bpf_skb_load_bytes(skb, off, addr, sizeof(addr));
Same verifier restrictions apply as in ffeedafbf023 ("bpf: introduce
current->pid, tgid, uid, gid, comm accessors") case, where stack memory
access needs to be statically verified and thus guaranteed to be
initialized in first use (otherwise verifier cannot tell whether a
subsequent access to it is valid or not as it's runtime dependent).
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-17 15:51:53 -07:00
|
|
|
if (ptr != to)
|
|
|
|
memcpy(to, ptr, len);
|
|
|
|
|
|
|
|
return 0;
|
2016-04-12 16:10:52 -06:00
|
|
|
err_clear:
|
|
|
|
memset(to, 0, len);
|
|
|
|
return -EFAULT;
|
bpf: add bpf_skb_load_bytes helper
When hacking tc programs with eBPF, one of the issues that come up
from time to time is to load addresses from headers. In eBPF as in
classic BPF, we have BPF_LD | BPF_ABS | BPF_{B,H,W} instructions that
extract a byte, half-word or word out of the skb data though helpers
such as bpf_load_pointer() (interpreter case).
F.e. extracting a whole IPv6 address could possibly look like ...
union v6addr {
struct {
__u32 p1;
__u32 p2;
__u32 p3;
__u32 p4;
};
__u8 addr[16];
};
[...]
a.p1 = htonl(load_word(skb, off));
a.p2 = htonl(load_word(skb, off + 4));
a.p3 = htonl(load_word(skb, off + 8));
a.p4 = htonl(load_word(skb, off + 12));
[...]
/* access to a.addr[...] */
This work adds a complementary helper bpf_skb_load_bytes() (we also
have bpf_skb_store_bytes()) as an alternative where the same call
would look like from an eBPF program:
ret = bpf_skb_load_bytes(skb, off, addr, sizeof(addr));
Same verifier restrictions apply as in ffeedafbf023 ("bpf: introduce
current->pid, tgid, uid, gid, comm accessors") case, where stack memory
access needs to be statically verified and thus guaranteed to be
initialized in first use (otherwise verifier cannot tell whether a
subsequent access to it is valid or not as it's runtime dependent).
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-17 15:51:53 -07:00
|
|
|
}
|
|
|
|
|
2016-03-04 07:15:04 -07:00
|
|
|
static const struct bpf_func_proto bpf_skb_load_bytes_proto = {
|
bpf: add bpf_skb_load_bytes helper
When hacking tc programs with eBPF, one of the issues that come up
from time to time is to load addresses from headers. In eBPF as in
classic BPF, we have BPF_LD | BPF_ABS | BPF_{B,H,W} instructions that
extract a byte, half-word or word out of the skb data though helpers
such as bpf_load_pointer() (interpreter case).
F.e. extracting a whole IPv6 address could possibly look like ...
union v6addr {
struct {
__u32 p1;
__u32 p2;
__u32 p3;
__u32 p4;
};
__u8 addr[16];
};
[...]
a.p1 = htonl(load_word(skb, off));
a.p2 = htonl(load_word(skb, off + 4));
a.p3 = htonl(load_word(skb, off + 8));
a.p4 = htonl(load_word(skb, off + 12));
[...]
/* access to a.addr[...] */
This work adds a complementary helper bpf_skb_load_bytes() (we also
have bpf_skb_store_bytes()) as an alternative where the same call
would look like from an eBPF program:
ret = bpf_skb_load_bytes(skb, off, addr, sizeof(addr));
Same verifier restrictions apply as in ffeedafbf023 ("bpf: introduce
current->pid, tgid, uid, gid, comm accessors") case, where stack memory
access needs to be statically verified and thus guaranteed to be
initialized in first use (otherwise verifier cannot tell whether a
subsequent access to it is valid or not as it's runtime dependent).
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-17 15:51:53 -07:00
|
|
|
.func = bpf_skb_load_bytes,
|
|
|
|
.gpl_only = false,
|
|
|
|
.ret_type = RET_INTEGER,
|
|
|
|
.arg1_type = ARG_PTR_TO_CTX,
|
|
|
|
.arg2_type = ARG_ANYTHING,
|
2016-04-12 16:10:52 -06:00
|
|
|
.arg3_type = ARG_PTR_TO_RAW_STACK,
|
bpf: add bpf_skb_load_bytes helper
When hacking tc programs with eBPF, one of the issues that come up
from time to time is to load addresses from headers. In eBPF as in
classic BPF, we have BPF_LD | BPF_ABS | BPF_{B,H,W} instructions that
extract a byte, half-word or word out of the skb data though helpers
such as bpf_load_pointer() (interpreter case).
F.e. extracting a whole IPv6 address could possibly look like ...
union v6addr {
struct {
__u32 p1;
__u32 p2;
__u32 p3;
__u32 p4;
};
__u8 addr[16];
};
[...]
a.p1 = htonl(load_word(skb, off));
a.p2 = htonl(load_word(skb, off + 4));
a.p3 = htonl(load_word(skb, off + 8));
a.p4 = htonl(load_word(skb, off + 12));
[...]
/* access to a.addr[...] */
This work adds a complementary helper bpf_skb_load_bytes() (we also
have bpf_skb_store_bytes()) as an alternative where the same call
would look like from an eBPF program:
ret = bpf_skb_load_bytes(skb, off, addr, sizeof(addr));
Same verifier restrictions apply as in ffeedafbf023 ("bpf: introduce
current->pid, tgid, uid, gid, comm accessors") case, where stack memory
access needs to be statically verified and thus guaranteed to be
initialized in first use (otherwise verifier cannot tell whether a
subsequent access to it is valid or not as it's runtime dependent).
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-17 15:51:53 -07:00
|
|
|
.arg4_type = ARG_CONST_STACK_SIZE,
|
|
|
|
};
|
|
|
|
|
2015-04-15 13:55:45 -06:00
|
|
|
static u64 bpf_l3_csum_replace(u64 r1, u64 r2, u64 from, u64 to, u64 flags)
|
2015-04-01 18:12:13 -06:00
|
|
|
{
|
|
|
|
struct sk_buff *skb = (struct sk_buff *) (long) r1;
|
2015-04-15 13:55:45 -06:00
|
|
|
int offset = (int) r2;
|
2015-04-01 18:12:13 -06:00
|
|
|
__sum16 sum, *ptr;
|
|
|
|
|
2016-01-10 17:16:38 -07:00
|
|
|
if (unlikely(flags & ~(BPF_F_HDR_FIELD_MASK)))
|
|
|
|
return -EINVAL;
|
2015-04-15 13:55:45 -06:00
|
|
|
if (unlikely((u32) offset > 0xffff))
|
2015-04-01 18:12:13 -06:00
|
|
|
return -EFAULT;
|
2016-05-05 20:49:12 -06:00
|
|
|
if (unlikely(bpf_try_make_writable(skb, offset + sizeof(sum))))
|
2015-04-01 18:12:13 -06:00
|
|
|
return -EFAULT;
|
|
|
|
|
|
|
|
ptr = skb_header_pointer(skb, offset, sizeof(sum), &sum);
|
|
|
|
if (unlikely(!ptr))
|
|
|
|
return -EFAULT;
|
|
|
|
|
2016-01-10 17:16:38 -07:00
|
|
|
switch (flags & BPF_F_HDR_FIELD_MASK) {
|
bpf: allow bpf_csum_diff to feed bpf_l3_csum_replace as well
Commit 7d672345ed29 ("bpf: add generic bpf_csum_diff helper") added a
generic checksum diff helper that can feed bpf_l4_csum_replace() with
a target __wsum diff that is to be applied to the L4 checksum. This
facility is very flexible, can be cascaded, allows for adding, removing,
or diffing data, or for calculating the pseudo header checksum from
scratch, but it can also be reused for working with the IPv4 header
checksum.
Thus, analogous to bpf_l4_csum_replace(), add a case for header field
value of 0 to change the checksum at a given offset through a new helper
csum_replace_by_diff(). Also, in addition to that, this provides an
easy to use interface for feeding precalculated diffs f.e. coming from
a map. It nicely complements bpf_l3_csum_replace() that currently allows
only for csum updates of 2 and 4 byte diffs.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-04 07:15:02 -07:00
|
|
|
case 0:
|
|
|
|
if (unlikely(from != 0))
|
|
|
|
return -EINVAL;
|
|
|
|
|
|
|
|
csum_replace_by_diff(ptr, to);
|
|
|
|
break;
|
2015-04-01 18:12:13 -06:00
|
|
|
case 2:
|
|
|
|
csum_replace2(ptr, from, to);
|
|
|
|
break;
|
|
|
|
case 4:
|
|
|
|
csum_replace4(ptr, from, to);
|
|
|
|
break;
|
|
|
|
default:
|
|
|
|
return -EINVAL;
|
|
|
|
}
|
|
|
|
|
|
|
|
if (ptr == &sum)
|
|
|
|
/* skb_store_bits guaranteed to not return -EFAULT here */
|
|
|
|
skb_store_bits(skb, offset, ptr, sizeof(sum));
|
|
|
|
|
|
|
|
return 0;
|
|
|
|
}
|
|
|
|
|
2016-03-04 07:15:04 -07:00
|
|
|
static const struct bpf_func_proto bpf_l3_csum_replace_proto = {
|
2015-04-01 18:12:13 -06:00
|
|
|
.func = bpf_l3_csum_replace,
|
|
|
|
.gpl_only = false,
|
|
|
|
.ret_type = RET_INTEGER,
|
|
|
|
.arg1_type = ARG_PTR_TO_CTX,
|
|
|
|
.arg2_type = ARG_ANYTHING,
|
|
|
|
.arg3_type = ARG_ANYTHING,
|
|
|
|
.arg4_type = ARG_ANYTHING,
|
|
|
|
.arg5_type = ARG_ANYTHING,
|
|
|
|
};
|
|
|
|
|
2015-04-15 13:55:45 -06:00
|
|
|
static u64 bpf_l4_csum_replace(u64 r1, u64 r2, u64 from, u64 to, u64 flags)
|
2015-04-01 18:12:13 -06:00
|
|
|
{
|
|
|
|
struct sk_buff *skb = (struct sk_buff *) (long) r1;
|
2016-01-10 17:16:38 -07:00
|
|
|
bool is_pseudo = flags & BPF_F_PSEUDO_HDR;
|
2016-02-19 15:05:26 -07:00
|
|
|
bool is_mmzero = flags & BPF_F_MARK_MANGLED_0;
|
2015-04-15 13:55:45 -06:00
|
|
|
int offset = (int) r2;
|
2015-04-01 18:12:13 -06:00
|
|
|
__sum16 sum, *ptr;
|
|
|
|
|
2016-02-19 15:05:26 -07:00
|
|
|
if (unlikely(flags & ~(BPF_F_MARK_MANGLED_0 | BPF_F_PSEUDO_HDR |
|
|
|
|
BPF_F_HDR_FIELD_MASK)))
|
2016-01-10 17:16:38 -07:00
|
|
|
return -EINVAL;
|
2015-04-15 13:55:45 -06:00
|
|
|
if (unlikely((u32) offset > 0xffff))
|
2015-04-01 18:12:13 -06:00
|
|
|
return -EFAULT;
|
2016-05-05 20:49:12 -06:00
|
|
|
if (unlikely(bpf_try_make_writable(skb, offset + sizeof(sum))))
|
2015-04-01 18:12:13 -06:00
|
|
|
return -EFAULT;
|
|
|
|
|
|
|
|
ptr = skb_header_pointer(skb, offset, sizeof(sum), &sum);
|
|
|
|
if (unlikely(!ptr))
|
|
|
|
return -EFAULT;
|
2016-02-19 15:05:26 -07:00
|
|
|
if (is_mmzero && !*ptr)
|
|
|
|
return 0;
|
2015-04-01 18:12:13 -06:00
|
|
|
|
2016-01-10 17:16:38 -07:00
|
|
|
switch (flags & BPF_F_HDR_FIELD_MASK) {
|
bpf: add generic bpf_csum_diff helper
For L4 checksums, we currently have bpf_l4_csum_replace() helper. It's
currently limited to handle 2 and 4 byte changes in a header and feeds the
from/to into inet_proto_csum_replace{2,4}() helpers of the kernel. When
working with IPv6, for example, this makes it rather cumbersome to deal
with, similarly when editing larger parts of a header.
Instead, extend the API in a more generic way: For bpf_l4_csum_replace(),
add a case for header field mask of 0 to change the checksum at a given
offset through inet_proto_csum_replace_by_diff(), and provide a helper
bpf_csum_diff() that can generically calculate a from/to diff for arbitrary
amounts of data.
This can be used in multiple ways: for the bpf_l4_csum_replace() only
part, this even provides us with the option to insert precalculated diffs
from user space f.e. from a map, or from bpf_csum_diff() during runtime.
bpf_csum_diff() has a optional from/to stack buffer input, so we can
calculate a diff by using a scratchbuffer for scenarios where we're
inserting (from is NULL), removing (to is NULL) or diffing (from/to buffers
don't need to be of equal size) data. Also, bpf_csum_diff() allows to
feed a previous csum into csum_partial(), so the function can also be
cascaded.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-02-19 15:05:23 -07:00
|
|
|
case 0:
|
|
|
|
if (unlikely(from != 0))
|
|
|
|
return -EINVAL;
|
|
|
|
|
|
|
|
inet_proto_csum_replace_by_diff(ptr, skb, to, is_pseudo);
|
|
|
|
break;
|
2015-04-01 18:12:13 -06:00
|
|
|
case 2:
|
|
|
|
inet_proto_csum_replace2(ptr, skb, from, to, is_pseudo);
|
|
|
|
break;
|
|
|
|
case 4:
|
|
|
|
inet_proto_csum_replace4(ptr, skb, from, to, is_pseudo);
|
|
|
|
break;
|
|
|
|
default:
|
|
|
|
return -EINVAL;
|
|
|
|
}
|
|
|
|
|
2016-02-19 15:05:26 -07:00
|
|
|
if (is_mmzero && !*ptr)
|
|
|
|
*ptr = CSUM_MANGLED_0;
|
2015-04-01 18:12:13 -06:00
|
|
|
if (ptr == &sum)
|
|
|
|
/* skb_store_bits guaranteed to not return -EFAULT here */
|
|
|
|
skb_store_bits(skb, offset, ptr, sizeof(sum));
|
|
|
|
|
|
|
|
return 0;
|
|
|
|
}
|
|
|
|
|
2016-03-04 07:15:04 -07:00
|
|
|
static const struct bpf_func_proto bpf_l4_csum_replace_proto = {
|
2015-04-01 18:12:13 -06:00
|
|
|
.func = bpf_l4_csum_replace,
|
|
|
|
.gpl_only = false,
|
|
|
|
.ret_type = RET_INTEGER,
|
|
|
|
.arg1_type = ARG_PTR_TO_CTX,
|
|
|
|
.arg2_type = ARG_ANYTHING,
|
|
|
|
.arg3_type = ARG_ANYTHING,
|
|
|
|
.arg4_type = ARG_ANYTHING,
|
|
|
|
.arg5_type = ARG_ANYTHING,
|
2015-03-26 20:53:57 -06:00
|
|
|
};
|
|
|
|
|
bpf: add generic bpf_csum_diff helper
For L4 checksums, we currently have bpf_l4_csum_replace() helper. It's
currently limited to handle 2 and 4 byte changes in a header and feeds the
from/to into inet_proto_csum_replace{2,4}() helpers of the kernel. When
working with IPv6, for example, this makes it rather cumbersome to deal
with, similarly when editing larger parts of a header.
Instead, extend the API in a more generic way: For bpf_l4_csum_replace(),
add a case for header field mask of 0 to change the checksum at a given
offset through inet_proto_csum_replace_by_diff(), and provide a helper
bpf_csum_diff() that can generically calculate a from/to diff for arbitrary
amounts of data.
This can be used in multiple ways: for the bpf_l4_csum_replace() only
part, this even provides us with the option to insert precalculated diffs
from user space f.e. from a map, or from bpf_csum_diff() during runtime.
bpf_csum_diff() has a optional from/to stack buffer input, so we can
calculate a diff by using a scratchbuffer for scenarios where we're
inserting (from is NULL), removing (to is NULL) or diffing (from/to buffers
don't need to be of equal size) data. Also, bpf_csum_diff() allows to
feed a previous csum into csum_partial(), so the function can also be
cascaded.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-02-19 15:05:23 -07:00
|
|
|
static u64 bpf_csum_diff(u64 r1, u64 from_size, u64 r3, u64 to_size, u64 seed)
|
|
|
|
{
|
2016-02-19 15:05:24 -07:00
|
|
|
struct bpf_scratchpad *sp = this_cpu_ptr(&bpf_sp);
|
bpf: add generic bpf_csum_diff helper
For L4 checksums, we currently have bpf_l4_csum_replace() helper. It's
currently limited to handle 2 and 4 byte changes in a header and feeds the
from/to into inet_proto_csum_replace{2,4}() helpers of the kernel. When
working with IPv6, for example, this makes it rather cumbersome to deal
with, similarly when editing larger parts of a header.
Instead, extend the API in a more generic way: For bpf_l4_csum_replace(),
add a case for header field mask of 0 to change the checksum at a given
offset through inet_proto_csum_replace_by_diff(), and provide a helper
bpf_csum_diff() that can generically calculate a from/to diff for arbitrary
amounts of data.
This can be used in multiple ways: for the bpf_l4_csum_replace() only
part, this even provides us with the option to insert precalculated diffs
from user space f.e. from a map, or from bpf_csum_diff() during runtime.
bpf_csum_diff() has a optional from/to stack buffer input, so we can
calculate a diff by using a scratchbuffer for scenarios where we're
inserting (from is NULL), removing (to is NULL) or diffing (from/to buffers
don't need to be of equal size) data. Also, bpf_csum_diff() allows to
feed a previous csum into csum_partial(), so the function can also be
cascaded.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-02-19 15:05:23 -07:00
|
|
|
u64 diff_size = from_size + to_size;
|
|
|
|
__be32 *from = (__be32 *) (long) r1;
|
|
|
|
__be32 *to = (__be32 *) (long) r3;
|
|
|
|
int i, j = 0;
|
|
|
|
|
|
|
|
/* This is quite flexible, some examples:
|
|
|
|
*
|
|
|
|
* from_size == 0, to_size > 0, seed := csum --> pushing data
|
|
|
|
* from_size > 0, to_size == 0, seed := csum --> pulling data
|
|
|
|
* from_size > 0, to_size > 0, seed := 0 --> diffing data
|
|
|
|
*
|
|
|
|
* Even for diffing, from_size and to_size don't need to be equal.
|
|
|
|
*/
|
|
|
|
if (unlikely(((from_size | to_size) & (sizeof(__be32) - 1)) ||
|
|
|
|
diff_size > sizeof(sp->diff)))
|
|
|
|
return -EINVAL;
|
|
|
|
|
|
|
|
for (i = 0; i < from_size / sizeof(__be32); i++, j++)
|
|
|
|
sp->diff[j] = ~from[i];
|
|
|
|
for (i = 0; i < to_size / sizeof(__be32); i++, j++)
|
|
|
|
sp->diff[j] = to[i];
|
|
|
|
|
|
|
|
return csum_partial(sp->diff, diff_size, seed);
|
|
|
|
}
|
|
|
|
|
2016-03-04 07:15:04 -07:00
|
|
|
static const struct bpf_func_proto bpf_csum_diff_proto = {
|
bpf: add generic bpf_csum_diff helper
For L4 checksums, we currently have bpf_l4_csum_replace() helper. It's
currently limited to handle 2 and 4 byte changes in a header and feeds the
from/to into inet_proto_csum_replace{2,4}() helpers of the kernel. When
working with IPv6, for example, this makes it rather cumbersome to deal
with, similarly when editing larger parts of a header.
Instead, extend the API in a more generic way: For bpf_l4_csum_replace(),
add a case for header field mask of 0 to change the checksum at a given
offset through inet_proto_csum_replace_by_diff(), and provide a helper
bpf_csum_diff() that can generically calculate a from/to diff for arbitrary
amounts of data.
This can be used in multiple ways: for the bpf_l4_csum_replace() only
part, this even provides us with the option to insert precalculated diffs
from user space f.e. from a map, or from bpf_csum_diff() during runtime.
bpf_csum_diff() has a optional from/to stack buffer input, so we can
calculate a diff by using a scratchbuffer for scenarios where we're
inserting (from is NULL), removing (to is NULL) or diffing (from/to buffers
don't need to be of equal size) data. Also, bpf_csum_diff() allows to
feed a previous csum into csum_partial(), so the function can also be
cascaded.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-02-19 15:05:23 -07:00
|
|
|
.func = bpf_csum_diff,
|
|
|
|
.gpl_only = false,
|
|
|
|
.ret_type = RET_INTEGER,
|
|
|
|
.arg1_type = ARG_PTR_TO_STACK,
|
|
|
|
.arg2_type = ARG_CONST_STACK_SIZE_OR_ZERO,
|
|
|
|
.arg3_type = ARG_PTR_TO_STACK,
|
|
|
|
.arg4_type = ARG_CONST_STACK_SIZE_OR_ZERO,
|
|
|
|
.arg5_type = ARG_ANYTHING,
|
|
|
|
};
|
|
|
|
|
2015-06-02 17:03:14 -06:00
|
|
|
static u64 bpf_clone_redirect(u64 r1, u64 ifindex, u64 flags, u64 r4, u64 r5)
|
|
|
|
{
|
|
|
|
struct sk_buff *skb = (struct sk_buff *) (long) r1, *skb2;
|
|
|
|
struct net_device *dev;
|
|
|
|
|
2016-01-10 17:16:38 -07:00
|
|
|
if (unlikely(flags & ~(BPF_F_INGRESS)))
|
|
|
|
return -EINVAL;
|
|
|
|
|
2015-06-02 17:03:14 -06:00
|
|
|
dev = dev_get_by_index_rcu(dev_net(skb->dev), ifindex);
|
|
|
|
if (unlikely(!dev))
|
|
|
|
return -EINVAL;
|
|
|
|
|
|
|
|
skb2 = skb_clone(skb, GFP_ATOMIC);
|
|
|
|
if (unlikely(!skb2))
|
|
|
|
return -ENOMEM;
|
|
|
|
|
2016-01-10 17:16:38 -07:00
|
|
|
if (flags & BPF_F_INGRESS) {
|
2016-01-07 07:50:23 -07:00
|
|
|
if (skb_at_tc_ingress(skb2))
|
|
|
|
skb_postpush_rcsum(skb2, skb_mac_header(skb2),
|
|
|
|
skb2->mac_len);
|
2015-06-02 17:03:14 -06:00
|
|
|
return dev_forward_skb(dev, skb2);
|
2016-01-07 07:50:23 -07:00
|
|
|
}
|
2015-06-02 17:03:14 -06:00
|
|
|
|
|
|
|
skb2->dev = dev;
|
|
|
|
return dev_queue_xmit(skb2);
|
|
|
|
}
|
|
|
|
|
2016-03-04 07:15:04 -07:00
|
|
|
static const struct bpf_func_proto bpf_clone_redirect_proto = {
|
2015-06-02 17:03:14 -06:00
|
|
|
.func = bpf_clone_redirect,
|
|
|
|
.gpl_only = false,
|
|
|
|
.ret_type = RET_INTEGER,
|
|
|
|
.arg1_type = ARG_PTR_TO_CTX,
|
|
|
|
.arg2_type = ARG_ANYTHING,
|
|
|
|
.arg3_type = ARG_ANYTHING,
|
|
|
|
};
|
|
|
|
|
2015-09-16 00:05:43 -06:00
|
|
|
struct redirect_info {
|
|
|
|
u32 ifindex;
|
|
|
|
u32 flags;
|
|
|
|
};
|
|
|
|
|
|
|
|
static DEFINE_PER_CPU(struct redirect_info, redirect_info);
|
2016-01-10 17:16:38 -07:00
|
|
|
|
2015-09-16 00:05:43 -06:00
|
|
|
static u64 bpf_redirect(u64 ifindex, u64 flags, u64 r3, u64 r4, u64 r5)
|
|
|
|
{
|
|
|
|
struct redirect_info *ri = this_cpu_ptr(&redirect_info);
|
|
|
|
|
2016-01-10 17:16:38 -07:00
|
|
|
if (unlikely(flags & ~(BPF_F_INGRESS)))
|
|
|
|
return TC_ACT_SHOT;
|
|
|
|
|
2015-09-16 00:05:43 -06:00
|
|
|
ri->ifindex = ifindex;
|
|
|
|
ri->flags = flags;
|
2016-01-10 17:16:38 -07:00
|
|
|
|
2015-09-16 00:05:43 -06:00
|
|
|
return TC_ACT_REDIRECT;
|
|
|
|
}
|
|
|
|
|
|
|
|
int skb_do_redirect(struct sk_buff *skb)
|
|
|
|
{
|
|
|
|
struct redirect_info *ri = this_cpu_ptr(&redirect_info);
|
|
|
|
struct net_device *dev;
|
|
|
|
|
|
|
|
dev = dev_get_by_index_rcu(dev_net(skb->dev), ri->ifindex);
|
|
|
|
ri->ifindex = 0;
|
|
|
|
if (unlikely(!dev)) {
|
|
|
|
kfree_skb(skb);
|
|
|
|
return -EINVAL;
|
|
|
|
}
|
|
|
|
|
2016-01-10 17:16:38 -07:00
|
|
|
if (ri->flags & BPF_F_INGRESS) {
|
2016-01-07 07:50:23 -07:00
|
|
|
if (skb_at_tc_ingress(skb))
|
|
|
|
skb_postpush_rcsum(skb, skb_mac_header(skb),
|
|
|
|
skb->mac_len);
|
2015-09-16 00:05:43 -06:00
|
|
|
return dev_forward_skb(dev, skb);
|
2016-01-07 07:50:23 -07:00
|
|
|
}
|
2015-09-16 00:05:43 -06:00
|
|
|
|
|
|
|
skb->dev = dev;
|
|
|
|
return dev_queue_xmit(skb);
|
|
|
|
}
|
|
|
|
|
2016-03-04 07:15:04 -07:00
|
|
|
static const struct bpf_func_proto bpf_redirect_proto = {
|
2015-09-16 00:05:43 -06:00
|
|
|
.func = bpf_redirect,
|
|
|
|
.gpl_only = false,
|
|
|
|
.ret_type = RET_INTEGER,
|
|
|
|
.arg1_type = ARG_ANYTHING,
|
|
|
|
.arg2_type = ARG_ANYTHING,
|
|
|
|
};
|
|
|
|
|
2015-07-15 06:21:42 -06:00
|
|
|
static u64 bpf_get_cgroup_classid(u64 r1, u64 r2, u64 r3, u64 r4, u64 r5)
|
|
|
|
{
|
|
|
|
return task_get_classid((struct sk_buff *) (unsigned long) r1);
|
|
|
|
}
|
|
|
|
|
|
|
|
static const struct bpf_func_proto bpf_get_cgroup_classid_proto = {
|
|
|
|
.func = bpf_get_cgroup_classid,
|
|
|
|
.gpl_only = false,
|
|
|
|
.ret_type = RET_INTEGER,
|
|
|
|
.arg1_type = ARG_PTR_TO_CTX,
|
|
|
|
};
|
|
|
|
|
2015-09-29 17:41:51 -06:00
|
|
|
static u64 bpf_get_route_realm(u64 r1, u64 r2, u64 r3, u64 r4, u64 r5)
|
|
|
|
{
|
2016-03-15 18:42:50 -06:00
|
|
|
return dst_tclassid((struct sk_buff *) (unsigned long) r1);
|
2015-09-29 17:41:51 -06:00
|
|
|
}
|
|
|
|
|
|
|
|
static const struct bpf_func_proto bpf_get_route_realm_proto = {
|
|
|
|
.func = bpf_get_route_realm,
|
|
|
|
.gpl_only = false,
|
|
|
|
.ret_type = RET_INTEGER,
|
|
|
|
.arg1_type = ARG_PTR_TO_CTX,
|
|
|
|
};
|
|
|
|
|
2015-07-20 21:34:18 -06:00
|
|
|
static u64 bpf_skb_vlan_push(u64 r1, u64 r2, u64 vlan_tci, u64 r4, u64 r5)
|
|
|
|
{
|
|
|
|
struct sk_buff *skb = (struct sk_buff *) (long) r1;
|
|
|
|
__be16 vlan_proto = (__force __be16) r2;
|
2016-05-05 20:49:12 -06:00
|
|
|
int ret;
|
2015-07-20 21:34:18 -06:00
|
|
|
|
|
|
|
if (unlikely(vlan_proto != htons(ETH_P_8021Q) &&
|
|
|
|
vlan_proto != htons(ETH_P_8021AD)))
|
|
|
|
vlan_proto = htons(ETH_P_8021Q);
|
|
|
|
|
2016-05-05 20:49:12 -06:00
|
|
|
ret = skb_vlan_push(skb, vlan_proto, vlan_tci);
|
|
|
|
bpf_compute_data_end(skb);
|
|
|
|
return ret;
|
2015-07-20 21:34:18 -06:00
|
|
|
}
|
|
|
|
|
|
|
|
const struct bpf_func_proto bpf_skb_vlan_push_proto = {
|
|
|
|
.func = bpf_skb_vlan_push,
|
|
|
|
.gpl_only = false,
|
|
|
|
.ret_type = RET_INTEGER,
|
|
|
|
.arg1_type = ARG_PTR_TO_CTX,
|
|
|
|
.arg2_type = ARG_ANYTHING,
|
|
|
|
.arg3_type = ARG_ANYTHING,
|
|
|
|
};
|
2015-07-20 21:34:19 -06:00
|
|
|
EXPORT_SYMBOL_GPL(bpf_skb_vlan_push_proto);
|
2015-07-20 21:34:18 -06:00
|
|
|
|
|
|
|
static u64 bpf_skb_vlan_pop(u64 r1, u64 r2, u64 r3, u64 r4, u64 r5)
|
|
|
|
{
|
|
|
|
struct sk_buff *skb = (struct sk_buff *) (long) r1;
|
2016-05-05 20:49:12 -06:00
|
|
|
int ret;
|
2015-07-20 21:34:18 -06:00
|
|
|
|
2016-05-05 20:49:12 -06:00
|
|
|
ret = skb_vlan_pop(skb);
|
|
|
|
bpf_compute_data_end(skb);
|
|
|
|
return ret;
|
2015-07-20 21:34:18 -06:00
|
|
|
}
|
|
|
|
|
|
|
|
const struct bpf_func_proto bpf_skb_vlan_pop_proto = {
|
|
|
|
.func = bpf_skb_vlan_pop,
|
|
|
|
.gpl_only = false,
|
|
|
|
.ret_type = RET_INTEGER,
|
|
|
|
.arg1_type = ARG_PTR_TO_CTX,
|
|
|
|
};
|
2015-07-20 21:34:19 -06:00
|
|
|
EXPORT_SYMBOL_GPL(bpf_skb_vlan_pop_proto);
|
2015-07-20 21:34:18 -06:00
|
|
|
|
|
|
|
bool bpf_helper_changes_skb_data(void *func)
|
|
|
|
{
|
|
|
|
if (func == bpf_skb_vlan_push)
|
|
|
|
return true;
|
|
|
|
if (func == bpf_skb_vlan_pop)
|
|
|
|
return true;
|
2016-02-19 15:05:25 -07:00
|
|
|
if (func == bpf_skb_store_bytes)
|
|
|
|
return true;
|
|
|
|
if (func == bpf_l3_csum_replace)
|
|
|
|
return true;
|
|
|
|
if (func == bpf_l4_csum_replace)
|
|
|
|
return true;
|
|
|
|
|
2015-07-20 21:34:18 -06:00
|
|
|
return false;
|
|
|
|
}
|
|
|
|
|
2016-01-10 17:16:39 -07:00
|
|
|
static unsigned short bpf_tunnel_key_af(u64 flags)
|
|
|
|
{
|
|
|
|
return flags & BPF_F_TUNINFO_IPV6 ? AF_INET6 : AF_INET;
|
|
|
|
}
|
|
|
|
|
bpf: add helpers to access tunnel metadata
Introduce helpers to let eBPF programs attached to TC manipulate tunnel metadata:
bpf_skb_[gs]et_tunnel_key(skb, key, size, flags)
skb: pointer to skb
key: pointer to 'struct bpf_tunnel_key'
size: size of 'struct bpf_tunnel_key'
flags: room for future extensions
First eBPF program that uses these helpers will allocate per_cpu
metadata_dst structures that will be used on TX.
On RX metadata_dst is allocated by tunnel driver.
Typical usage for TX:
struct bpf_tunnel_key tkey;
... populate tkey ...
bpf_skb_set_tunnel_key(skb, &tkey, sizeof(tkey), 0);
bpf_clone_redirect(skb, vxlan_dev_ifindex, 0);
RX:
struct bpf_tunnel_key tkey = {};
bpf_skb_get_tunnel_key(skb, &tkey, sizeof(tkey), 0);
... lookup or redirect based on tkey ...
'struct bpf_tunnel_key' will be extended in the future by adding
elements to the end and the 'size' argument will indicate which fields
are populated, thereby keeping backwards compatibility.
The 'flags' argument may be used as well when the 'size' is not enough or
to indicate completely different layout of bpf_tunnel_key.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-30 16:36:57 -06:00
|
|
|
static u64 bpf_skb_get_tunnel_key(u64 r1, u64 r2, u64 size, u64 flags, u64 r5)
|
|
|
|
{
|
|
|
|
struct sk_buff *skb = (struct sk_buff *) (long) r1;
|
|
|
|
struct bpf_tunnel_key *to = (struct bpf_tunnel_key *) (long) r2;
|
2016-01-10 17:16:39 -07:00
|
|
|
const struct ip_tunnel_info *info = skb_tunnel_info(skb);
|
|
|
|
u8 compat[sizeof(struct bpf_tunnel_key)];
|
2016-04-12 16:10:52 -06:00
|
|
|
void *to_orig = to;
|
|
|
|
int err;
|
bpf: add helpers to access tunnel metadata
Introduce helpers to let eBPF programs attached to TC manipulate tunnel metadata:
bpf_skb_[gs]et_tunnel_key(skb, key, size, flags)
skb: pointer to skb
key: pointer to 'struct bpf_tunnel_key'
size: size of 'struct bpf_tunnel_key'
flags: room for future extensions
First eBPF program that uses these helpers will allocate per_cpu
metadata_dst structures that will be used on TX.
On RX metadata_dst is allocated by tunnel driver.
Typical usage for TX:
struct bpf_tunnel_key tkey;
... populate tkey ...
bpf_skb_set_tunnel_key(skb, &tkey, sizeof(tkey), 0);
bpf_clone_redirect(skb, vxlan_dev_ifindex, 0);
RX:
struct bpf_tunnel_key tkey = {};
bpf_skb_get_tunnel_key(skb, &tkey, sizeof(tkey), 0);
... lookup or redirect based on tkey ...
'struct bpf_tunnel_key' will be extended in the future by adding
elements to the end and the 'size' argument will indicate which fields
are populated, thereby keeping backwards compatibility.
The 'flags' argument may be used as well when the 'size' is not enough or
to indicate completely different layout of bpf_tunnel_key.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-30 16:36:57 -06:00
|
|
|
|
2016-04-12 16:10:52 -06:00
|
|
|
if (unlikely(!info || (flags & ~(BPF_F_TUNINFO_IPV6)))) {
|
|
|
|
err = -EINVAL;
|
|
|
|
goto err_clear;
|
|
|
|
}
|
|
|
|
if (ip_tunnel_info_af(info) != bpf_tunnel_key_af(flags)) {
|
|
|
|
err = -EPROTO;
|
|
|
|
goto err_clear;
|
|
|
|
}
|
2016-01-10 17:16:39 -07:00
|
|
|
if (unlikely(size != sizeof(struct bpf_tunnel_key))) {
|
2016-04-12 16:10:52 -06:00
|
|
|
err = -EINVAL;
|
2016-01-10 17:16:39 -07:00
|
|
|
switch (size) {
|
2016-03-08 19:00:05 -07:00
|
|
|
case offsetof(struct bpf_tunnel_key, tunnel_label):
|
2016-03-29 16:02:00 -06:00
|
|
|
case offsetof(struct bpf_tunnel_key, tunnel_ext):
|
2016-03-08 19:00:05 -07:00
|
|
|
goto set_compat;
|
2016-01-10 17:16:39 -07:00
|
|
|
case offsetof(struct bpf_tunnel_key, remote_ipv6[1]):
|
|
|
|
/* Fixup deprecated structure layouts here, so we have
|
|
|
|
* a common path later on.
|
|
|
|
*/
|
|
|
|
if (ip_tunnel_info_af(info) != AF_INET)
|
2016-04-12 16:10:52 -06:00
|
|
|
goto err_clear;
|
2016-03-08 19:00:05 -07:00
|
|
|
set_compat:
|
2016-01-10 17:16:39 -07:00
|
|
|
to = (struct bpf_tunnel_key *)compat;
|
|
|
|
break;
|
|
|
|
default:
|
2016-04-12 16:10:52 -06:00
|
|
|
goto err_clear;
|
2016-01-10 17:16:39 -07:00
|
|
|
}
|
|
|
|
}
|
bpf: add helpers to access tunnel metadata
Introduce helpers to let eBPF programs attached to TC manipulate tunnel metadata:
bpf_skb_[gs]et_tunnel_key(skb, key, size, flags)
skb: pointer to skb
key: pointer to 'struct bpf_tunnel_key'
size: size of 'struct bpf_tunnel_key'
flags: room for future extensions
First eBPF program that uses these helpers will allocate per_cpu
metadata_dst structures that will be used on TX.
On RX metadata_dst is allocated by tunnel driver.
Typical usage for TX:
struct bpf_tunnel_key tkey;
... populate tkey ...
bpf_skb_set_tunnel_key(skb, &tkey, sizeof(tkey), 0);
bpf_clone_redirect(skb, vxlan_dev_ifindex, 0);
RX:
struct bpf_tunnel_key tkey = {};
bpf_skb_get_tunnel_key(skb, &tkey, sizeof(tkey), 0);
... lookup or redirect based on tkey ...
'struct bpf_tunnel_key' will be extended in the future by adding
elements to the end and the 'size' argument will indicate which fields
are populated, thereby keeping backwards compatibility.
The 'flags' argument may be used as well when the 'size' is not enough or
to indicate completely different layout of bpf_tunnel_key.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-30 16:36:57 -06:00
|
|
|
|
|
|
|
to->tunnel_id = be64_to_cpu(info->key.tun_id);
|
2016-01-10 17:16:39 -07:00
|
|
|
to->tunnel_tos = info->key.tos;
|
|
|
|
to->tunnel_ttl = info->key.ttl;
|
|
|
|
|
2016-03-08 19:00:05 -07:00
|
|
|
if (flags & BPF_F_TUNINFO_IPV6) {
|
2016-01-10 17:16:39 -07:00
|
|
|
memcpy(to->remote_ipv6, &info->key.u.ipv6.src,
|
|
|
|
sizeof(to->remote_ipv6));
|
2016-03-08 19:00:05 -07:00
|
|
|
to->tunnel_label = be32_to_cpu(info->key.label);
|
|
|
|
} else {
|
2016-01-10 17:16:39 -07:00
|
|
|
to->remote_ipv4 = be32_to_cpu(info->key.u.ipv4.src);
|
2016-03-08 19:00:05 -07:00
|
|
|
}
|
2016-01-10 17:16:39 -07:00
|
|
|
|
|
|
|
if (unlikely(size != sizeof(struct bpf_tunnel_key)))
|
2016-04-12 16:10:52 -06:00
|
|
|
memcpy(to_orig, to, size);
|
bpf: add helpers to access tunnel metadata
Introduce helpers to let eBPF programs attached to TC manipulate tunnel metadata:
bpf_skb_[gs]et_tunnel_key(skb, key, size, flags)
skb: pointer to skb
key: pointer to 'struct bpf_tunnel_key'
size: size of 'struct bpf_tunnel_key'
flags: room for future extensions
First eBPF program that uses these helpers will allocate per_cpu
metadata_dst structures that will be used on TX.
On RX metadata_dst is allocated by tunnel driver.
Typical usage for TX:
struct bpf_tunnel_key tkey;
... populate tkey ...
bpf_skb_set_tunnel_key(skb, &tkey, sizeof(tkey), 0);
bpf_clone_redirect(skb, vxlan_dev_ifindex, 0);
RX:
struct bpf_tunnel_key tkey = {};
bpf_skb_get_tunnel_key(skb, &tkey, sizeof(tkey), 0);
... lookup or redirect based on tkey ...
'struct bpf_tunnel_key' will be extended in the future by adding
elements to the end and the 'size' argument will indicate which fields
are populated, thereby keeping backwards compatibility.
The 'flags' argument may be used as well when the 'size' is not enough or
to indicate completely different layout of bpf_tunnel_key.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-30 16:36:57 -06:00
|
|
|
|
|
|
|
return 0;
|
2016-04-12 16:10:52 -06:00
|
|
|
err_clear:
|
|
|
|
memset(to_orig, 0, size);
|
|
|
|
return err;
|
bpf: add helpers to access tunnel metadata
Introduce helpers to let eBPF programs attached to TC manipulate tunnel metadata:
bpf_skb_[gs]et_tunnel_key(skb, key, size, flags)
skb: pointer to skb
key: pointer to 'struct bpf_tunnel_key'
size: size of 'struct bpf_tunnel_key'
flags: room for future extensions
First eBPF program that uses these helpers will allocate per_cpu
metadata_dst structures that will be used on TX.
On RX metadata_dst is allocated by tunnel driver.
Typical usage for TX:
struct bpf_tunnel_key tkey;
... populate tkey ...
bpf_skb_set_tunnel_key(skb, &tkey, sizeof(tkey), 0);
bpf_clone_redirect(skb, vxlan_dev_ifindex, 0);
RX:
struct bpf_tunnel_key tkey = {};
bpf_skb_get_tunnel_key(skb, &tkey, sizeof(tkey), 0);
... lookup or redirect based on tkey ...
'struct bpf_tunnel_key' will be extended in the future by adding
elements to the end and the 'size' argument will indicate which fields
are populated, thereby keeping backwards compatibility.
The 'flags' argument may be used as well when the 'size' is not enough or
to indicate completely different layout of bpf_tunnel_key.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-30 16:36:57 -06:00
|
|
|
}
|
|
|
|
|
2016-03-04 07:15:04 -07:00
|
|
|
static const struct bpf_func_proto bpf_skb_get_tunnel_key_proto = {
|
bpf: add helpers to access tunnel metadata
Introduce helpers to let eBPF programs attached to TC manipulate tunnel metadata:
bpf_skb_[gs]et_tunnel_key(skb, key, size, flags)
skb: pointer to skb
key: pointer to 'struct bpf_tunnel_key'
size: size of 'struct bpf_tunnel_key'
flags: room for future extensions
First eBPF program that uses these helpers will allocate per_cpu
metadata_dst structures that will be used on TX.
On RX metadata_dst is allocated by tunnel driver.
Typical usage for TX:
struct bpf_tunnel_key tkey;
... populate tkey ...
bpf_skb_set_tunnel_key(skb, &tkey, sizeof(tkey), 0);
bpf_clone_redirect(skb, vxlan_dev_ifindex, 0);
RX:
struct bpf_tunnel_key tkey = {};
bpf_skb_get_tunnel_key(skb, &tkey, sizeof(tkey), 0);
... lookup or redirect based on tkey ...
'struct bpf_tunnel_key' will be extended in the future by adding
elements to the end and the 'size' argument will indicate which fields
are populated, thereby keeping backwards compatibility.
The 'flags' argument may be used as well when the 'size' is not enough or
to indicate completely different layout of bpf_tunnel_key.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-30 16:36:57 -06:00
|
|
|
.func = bpf_skb_get_tunnel_key,
|
|
|
|
.gpl_only = false,
|
|
|
|
.ret_type = RET_INTEGER,
|
|
|
|
.arg1_type = ARG_PTR_TO_CTX,
|
2016-04-12 16:10:52 -06:00
|
|
|
.arg2_type = ARG_PTR_TO_RAW_STACK,
|
bpf: add helpers to access tunnel metadata
Introduce helpers to let eBPF programs attached to TC manipulate tunnel metadata:
bpf_skb_[gs]et_tunnel_key(skb, key, size, flags)
skb: pointer to skb
key: pointer to 'struct bpf_tunnel_key'
size: size of 'struct bpf_tunnel_key'
flags: room for future extensions
First eBPF program that uses these helpers will allocate per_cpu
metadata_dst structures that will be used on TX.
On RX metadata_dst is allocated by tunnel driver.
Typical usage for TX:
struct bpf_tunnel_key tkey;
... populate tkey ...
bpf_skb_set_tunnel_key(skb, &tkey, sizeof(tkey), 0);
bpf_clone_redirect(skb, vxlan_dev_ifindex, 0);
RX:
struct bpf_tunnel_key tkey = {};
bpf_skb_get_tunnel_key(skb, &tkey, sizeof(tkey), 0);
... lookup or redirect based on tkey ...
'struct bpf_tunnel_key' will be extended in the future by adding
elements to the end and the 'size' argument will indicate which fields
are populated, thereby keeping backwards compatibility.
The 'flags' argument may be used as well when the 'size' is not enough or
to indicate completely different layout of bpf_tunnel_key.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-30 16:36:57 -06:00
|
|
|
.arg3_type = ARG_CONST_STACK_SIZE,
|
|
|
|
.arg4_type = ARG_ANYTHING,
|
|
|
|
};
|
|
|
|
|
bpf: support for access to tunnel options
After eBPF being able to programmatically access/manage tunnel key meta
data via commit d3aa45ce6b94 ("bpf: add helpers to access tunnel metadata")
and more recently also for IPv6 through c6c33454072f ("bpf: support ipv6
for bpf_skb_{set,get}_tunnel_key"), this work adds two complementary
helpers to generically access their auxiliary tunnel options.
Geneve and vxlan support this facility. For geneve, TLVs can be pushed,
and for the vxlan case its GBP extension. I.e. setting tunnel key for geneve
case only makes sense, if we can also read/write TLVs into it. In the GBP
case, it provides the flexibility to easily map the group policy ID in
combination with other helpers or maps.
I chose to model this as two separate helpers, bpf_skb_{set,get}_tunnel_opt(),
for a couple of reasons. bpf_skb_{set,get}_tunnel_key() is already rather
complex by itself, and there may be cases for tunnel key backends where
tunnel options are not always needed. If we would have integrated this
into bpf_skb_{set,get}_tunnel_key() nevertheless, we are very limited with
remaining helper arguments, so keeping compatibility on structs in case of
passing in a flat buffer gets more cumbersome. Separating both also allows
for more flexibility and future extensibility, f.e. options could be fed
directly from a map, etc.
Moreover, change geneve's xmit path to test only for info->options_len
instead of TUNNEL_GENEVE_OPT flag. This makes it more consistent with vxlan's
xmit path and allows for avoiding to specify a protocol flag in the API on
xmit, so it can be protocol agnostic. Having info->options_len is enough
information that is needed. Tested with vxlan and geneve.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-04 07:15:06 -07:00
|
|
|
static u64 bpf_skb_get_tunnel_opt(u64 r1, u64 r2, u64 size, u64 r4, u64 r5)
|
|
|
|
{
|
|
|
|
struct sk_buff *skb = (struct sk_buff *) (long) r1;
|
|
|
|
u8 *to = (u8 *) (long) r2;
|
|
|
|
const struct ip_tunnel_info *info = skb_tunnel_info(skb);
|
2016-04-12 16:10:52 -06:00
|
|
|
int err;
|
bpf: support for access to tunnel options
After eBPF being able to programmatically access/manage tunnel key meta
data via commit d3aa45ce6b94 ("bpf: add helpers to access tunnel metadata")
and more recently also for IPv6 through c6c33454072f ("bpf: support ipv6
for bpf_skb_{set,get}_tunnel_key"), this work adds two complementary
helpers to generically access their auxiliary tunnel options.
Geneve and vxlan support this facility. For geneve, TLVs can be pushed,
and for the vxlan case its GBP extension. I.e. setting tunnel key for geneve
case only makes sense, if we can also read/write TLVs into it. In the GBP
case, it provides the flexibility to easily map the group policy ID in
combination with other helpers or maps.
I chose to model this as two separate helpers, bpf_skb_{set,get}_tunnel_opt(),
for a couple of reasons. bpf_skb_{set,get}_tunnel_key() is already rather
complex by itself, and there may be cases for tunnel key backends where
tunnel options are not always needed. If we would have integrated this
into bpf_skb_{set,get}_tunnel_key() nevertheless, we are very limited with
remaining helper arguments, so keeping compatibility on structs in case of
passing in a flat buffer gets more cumbersome. Separating both also allows
for more flexibility and future extensibility, f.e. options could be fed
directly from a map, etc.
Moreover, change geneve's xmit path to test only for info->options_len
instead of TUNNEL_GENEVE_OPT flag. This makes it more consistent with vxlan's
xmit path and allows for avoiding to specify a protocol flag in the API on
xmit, so it can be protocol agnostic. Having info->options_len is enough
information that is needed. Tested with vxlan and geneve.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-04 07:15:06 -07:00
|
|
|
|
|
|
|
if (unlikely(!info ||
|
2016-04-12 16:10:52 -06:00
|
|
|
!(info->key.tun_flags & TUNNEL_OPTIONS_PRESENT))) {
|
|
|
|
err = -ENOENT;
|
|
|
|
goto err_clear;
|
|
|
|
}
|
|
|
|
if (unlikely(size < info->options_len)) {
|
|
|
|
err = -ENOMEM;
|
|
|
|
goto err_clear;
|
|
|
|
}
|
bpf: support for access to tunnel options
After eBPF being able to programmatically access/manage tunnel key meta
data via commit d3aa45ce6b94 ("bpf: add helpers to access tunnel metadata")
and more recently also for IPv6 through c6c33454072f ("bpf: support ipv6
for bpf_skb_{set,get}_tunnel_key"), this work adds two complementary
helpers to generically access their auxiliary tunnel options.
Geneve and vxlan support this facility. For geneve, TLVs can be pushed,
and for the vxlan case its GBP extension. I.e. setting tunnel key for geneve
case only makes sense, if we can also read/write TLVs into it. In the GBP
case, it provides the flexibility to easily map the group policy ID in
combination with other helpers or maps.
I chose to model this as two separate helpers, bpf_skb_{set,get}_tunnel_opt(),
for a couple of reasons. bpf_skb_{set,get}_tunnel_key() is already rather
complex by itself, and there may be cases for tunnel key backends where
tunnel options are not always needed. If we would have integrated this
into bpf_skb_{set,get}_tunnel_key() nevertheless, we are very limited with
remaining helper arguments, so keeping compatibility on structs in case of
passing in a flat buffer gets more cumbersome. Separating both also allows
for more flexibility and future extensibility, f.e. options could be fed
directly from a map, etc.
Moreover, change geneve's xmit path to test only for info->options_len
instead of TUNNEL_GENEVE_OPT flag. This makes it more consistent with vxlan's
xmit path and allows for avoiding to specify a protocol flag in the API on
xmit, so it can be protocol agnostic. Having info->options_len is enough
information that is needed. Tested with vxlan and geneve.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-04 07:15:06 -07:00
|
|
|
|
|
|
|
ip_tunnel_info_opts_get(to, info);
|
2016-04-12 16:10:52 -06:00
|
|
|
if (size > info->options_len)
|
|
|
|
memset(to + info->options_len, 0, size - info->options_len);
|
bpf: support for access to tunnel options
After eBPF being able to programmatically access/manage tunnel key meta
data via commit d3aa45ce6b94 ("bpf: add helpers to access tunnel metadata")
and more recently also for IPv6 through c6c33454072f ("bpf: support ipv6
for bpf_skb_{set,get}_tunnel_key"), this work adds two complementary
helpers to generically access their auxiliary tunnel options.
Geneve and vxlan support this facility. For geneve, TLVs can be pushed,
and for the vxlan case its GBP extension. I.e. setting tunnel key for geneve
case only makes sense, if we can also read/write TLVs into it. In the GBP
case, it provides the flexibility to easily map the group policy ID in
combination with other helpers or maps.
I chose to model this as two separate helpers, bpf_skb_{set,get}_tunnel_opt(),
for a couple of reasons. bpf_skb_{set,get}_tunnel_key() is already rather
complex by itself, and there may be cases for tunnel key backends where
tunnel options are not always needed. If we would have integrated this
into bpf_skb_{set,get}_tunnel_key() nevertheless, we are very limited with
remaining helper arguments, so keeping compatibility on structs in case of
passing in a flat buffer gets more cumbersome. Separating both also allows
for more flexibility and future extensibility, f.e. options could be fed
directly from a map, etc.
Moreover, change geneve's xmit path to test only for info->options_len
instead of TUNNEL_GENEVE_OPT flag. This makes it more consistent with vxlan's
xmit path and allows for avoiding to specify a protocol flag in the API on
xmit, so it can be protocol agnostic. Having info->options_len is enough
information that is needed. Tested with vxlan and geneve.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-04 07:15:06 -07:00
|
|
|
|
|
|
|
return info->options_len;
|
2016-04-12 16:10:52 -06:00
|
|
|
err_clear:
|
|
|
|
memset(to, 0, size);
|
|
|
|
return err;
|
bpf: support for access to tunnel options
After eBPF being able to programmatically access/manage tunnel key meta
data via commit d3aa45ce6b94 ("bpf: add helpers to access tunnel metadata")
and more recently also for IPv6 through c6c33454072f ("bpf: support ipv6
for bpf_skb_{set,get}_tunnel_key"), this work adds two complementary
helpers to generically access their auxiliary tunnel options.
Geneve and vxlan support this facility. For geneve, TLVs can be pushed,
and for the vxlan case its GBP extension. I.e. setting tunnel key for geneve
case only makes sense, if we can also read/write TLVs into it. In the GBP
case, it provides the flexibility to easily map the group policy ID in
combination with other helpers or maps.
I chose to model this as two separate helpers, bpf_skb_{set,get}_tunnel_opt(),
for a couple of reasons. bpf_skb_{set,get}_tunnel_key() is already rather
complex by itself, and there may be cases for tunnel key backends where
tunnel options are not always needed. If we would have integrated this
into bpf_skb_{set,get}_tunnel_key() nevertheless, we are very limited with
remaining helper arguments, so keeping compatibility on structs in case of
passing in a flat buffer gets more cumbersome. Separating both also allows
for more flexibility and future extensibility, f.e. options could be fed
directly from a map, etc.
Moreover, change geneve's xmit path to test only for info->options_len
instead of TUNNEL_GENEVE_OPT flag. This makes it more consistent with vxlan's
xmit path and allows for avoiding to specify a protocol flag in the API on
xmit, so it can be protocol agnostic. Having info->options_len is enough
information that is needed. Tested with vxlan and geneve.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-04 07:15:06 -07:00
|
|
|
}
|
|
|
|
|
|
|
|
static const struct bpf_func_proto bpf_skb_get_tunnel_opt_proto = {
|
|
|
|
.func = bpf_skb_get_tunnel_opt,
|
|
|
|
.gpl_only = false,
|
|
|
|
.ret_type = RET_INTEGER,
|
|
|
|
.arg1_type = ARG_PTR_TO_CTX,
|
2016-04-12 16:10:52 -06:00
|
|
|
.arg2_type = ARG_PTR_TO_RAW_STACK,
|
bpf: support for access to tunnel options
After eBPF being able to programmatically access/manage tunnel key meta
data via commit d3aa45ce6b94 ("bpf: add helpers to access tunnel metadata")
and more recently also for IPv6 through c6c33454072f ("bpf: support ipv6
for bpf_skb_{set,get}_tunnel_key"), this work adds two complementary
helpers to generically access their auxiliary tunnel options.
Geneve and vxlan support this facility. For geneve, TLVs can be pushed,
and for the vxlan case its GBP extension. I.e. setting tunnel key for geneve
case only makes sense, if we can also read/write TLVs into it. In the GBP
case, it provides the flexibility to easily map the group policy ID in
combination with other helpers or maps.
I chose to model this as two separate helpers, bpf_skb_{set,get}_tunnel_opt(),
for a couple of reasons. bpf_skb_{set,get}_tunnel_key() is already rather
complex by itself, and there may be cases for tunnel key backends where
tunnel options are not always needed. If we would have integrated this
into bpf_skb_{set,get}_tunnel_key() nevertheless, we are very limited with
remaining helper arguments, so keeping compatibility on structs in case of
passing in a flat buffer gets more cumbersome. Separating both also allows
for more flexibility and future extensibility, f.e. options could be fed
directly from a map, etc.
Moreover, change geneve's xmit path to test only for info->options_len
instead of TUNNEL_GENEVE_OPT flag. This makes it more consistent with vxlan's
xmit path and allows for avoiding to specify a protocol flag in the API on
xmit, so it can be protocol agnostic. Having info->options_len is enough
information that is needed. Tested with vxlan and geneve.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-04 07:15:06 -07:00
|
|
|
.arg3_type = ARG_CONST_STACK_SIZE,
|
|
|
|
};
|
|
|
|
|
bpf: add helpers to access tunnel metadata
Introduce helpers to let eBPF programs attached to TC manipulate tunnel metadata:
bpf_skb_[gs]et_tunnel_key(skb, key, size, flags)
skb: pointer to skb
key: pointer to 'struct bpf_tunnel_key'
size: size of 'struct bpf_tunnel_key'
flags: room for future extensions
First eBPF program that uses these helpers will allocate per_cpu
metadata_dst structures that will be used on TX.
On RX metadata_dst is allocated by tunnel driver.
Typical usage for TX:
struct bpf_tunnel_key tkey;
... populate tkey ...
bpf_skb_set_tunnel_key(skb, &tkey, sizeof(tkey), 0);
bpf_clone_redirect(skb, vxlan_dev_ifindex, 0);
RX:
struct bpf_tunnel_key tkey = {};
bpf_skb_get_tunnel_key(skb, &tkey, sizeof(tkey), 0);
... lookup or redirect based on tkey ...
'struct bpf_tunnel_key' will be extended in the future by adding
elements to the end and the 'size' argument will indicate which fields
are populated, thereby keeping backwards compatibility.
The 'flags' argument may be used as well when the 'size' is not enough or
to indicate completely different layout of bpf_tunnel_key.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-30 16:36:57 -06:00
|
|
|
static struct metadata_dst __percpu *md_dst;
|
|
|
|
|
|
|
|
static u64 bpf_skb_set_tunnel_key(u64 r1, u64 r2, u64 size, u64 flags, u64 r5)
|
|
|
|
{
|
|
|
|
struct sk_buff *skb = (struct sk_buff *) (long) r1;
|
|
|
|
struct bpf_tunnel_key *from = (struct bpf_tunnel_key *) (long) r2;
|
|
|
|
struct metadata_dst *md = this_cpu_ptr(md_dst);
|
2016-01-10 17:16:39 -07:00
|
|
|
u8 compat[sizeof(struct bpf_tunnel_key)];
|
bpf: add helpers to access tunnel metadata
Introduce helpers to let eBPF programs attached to TC manipulate tunnel metadata:
bpf_skb_[gs]et_tunnel_key(skb, key, size, flags)
skb: pointer to skb
key: pointer to 'struct bpf_tunnel_key'
size: size of 'struct bpf_tunnel_key'
flags: room for future extensions
First eBPF program that uses these helpers will allocate per_cpu
metadata_dst structures that will be used on TX.
On RX metadata_dst is allocated by tunnel driver.
Typical usage for TX:
struct bpf_tunnel_key tkey;
... populate tkey ...
bpf_skb_set_tunnel_key(skb, &tkey, sizeof(tkey), 0);
bpf_clone_redirect(skb, vxlan_dev_ifindex, 0);
RX:
struct bpf_tunnel_key tkey = {};
bpf_skb_get_tunnel_key(skb, &tkey, sizeof(tkey), 0);
... lookup or redirect based on tkey ...
'struct bpf_tunnel_key' will be extended in the future by adding
elements to the end and the 'size' argument will indicate which fields
are populated, thereby keeping backwards compatibility.
The 'flags' argument may be used as well when the 'size' is not enough or
to indicate completely different layout of bpf_tunnel_key.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-30 16:36:57 -06:00
|
|
|
struct ip_tunnel_info *info;
|
|
|
|
|
2016-03-04 07:15:05 -07:00
|
|
|
if (unlikely(flags & ~(BPF_F_TUNINFO_IPV6 | BPF_F_ZERO_CSUM_TX |
|
|
|
|
BPF_F_DONT_FRAGMENT)))
|
bpf: add helpers to access tunnel metadata
Introduce helpers to let eBPF programs attached to TC manipulate tunnel metadata:
bpf_skb_[gs]et_tunnel_key(skb, key, size, flags)
skb: pointer to skb
key: pointer to 'struct bpf_tunnel_key'
size: size of 'struct bpf_tunnel_key'
flags: room for future extensions
First eBPF program that uses these helpers will allocate per_cpu
metadata_dst structures that will be used on TX.
On RX metadata_dst is allocated by tunnel driver.
Typical usage for TX:
struct bpf_tunnel_key tkey;
... populate tkey ...
bpf_skb_set_tunnel_key(skb, &tkey, sizeof(tkey), 0);
bpf_clone_redirect(skb, vxlan_dev_ifindex, 0);
RX:
struct bpf_tunnel_key tkey = {};
bpf_skb_get_tunnel_key(skb, &tkey, sizeof(tkey), 0);
... lookup or redirect based on tkey ...
'struct bpf_tunnel_key' will be extended in the future by adding
elements to the end and the 'size' argument will indicate which fields
are populated, thereby keeping backwards compatibility.
The 'flags' argument may be used as well when the 'size' is not enough or
to indicate completely different layout of bpf_tunnel_key.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-30 16:36:57 -06:00
|
|
|
return -EINVAL;
|
2016-01-10 17:16:39 -07:00
|
|
|
if (unlikely(size != sizeof(struct bpf_tunnel_key))) {
|
|
|
|
switch (size) {
|
2016-03-08 19:00:05 -07:00
|
|
|
case offsetof(struct bpf_tunnel_key, tunnel_label):
|
2016-03-29 16:02:00 -06:00
|
|
|
case offsetof(struct bpf_tunnel_key, tunnel_ext):
|
2016-01-10 17:16:39 -07:00
|
|
|
case offsetof(struct bpf_tunnel_key, remote_ipv6[1]):
|
|
|
|
/* Fixup deprecated structure layouts here, so we have
|
|
|
|
* a common path later on.
|
|
|
|
*/
|
|
|
|
memcpy(compat, from, size);
|
|
|
|
memset(compat + size, 0, sizeof(compat) - size);
|
|
|
|
from = (struct bpf_tunnel_key *)compat;
|
|
|
|
break;
|
|
|
|
default:
|
|
|
|
return -EINVAL;
|
|
|
|
}
|
|
|
|
}
|
2016-03-29 16:02:00 -06:00
|
|
|
if (unlikely((!(flags & BPF_F_TUNINFO_IPV6) && from->tunnel_label) ||
|
|
|
|
from->tunnel_ext))
|
2016-03-08 19:00:05 -07:00
|
|
|
return -EINVAL;
|
bpf: add helpers to access tunnel metadata
Introduce helpers to let eBPF programs attached to TC manipulate tunnel metadata:
bpf_skb_[gs]et_tunnel_key(skb, key, size, flags)
skb: pointer to skb
key: pointer to 'struct bpf_tunnel_key'
size: size of 'struct bpf_tunnel_key'
flags: room for future extensions
First eBPF program that uses these helpers will allocate per_cpu
metadata_dst structures that will be used on TX.
On RX metadata_dst is allocated by tunnel driver.
Typical usage for TX:
struct bpf_tunnel_key tkey;
... populate tkey ...
bpf_skb_set_tunnel_key(skb, &tkey, sizeof(tkey), 0);
bpf_clone_redirect(skb, vxlan_dev_ifindex, 0);
RX:
struct bpf_tunnel_key tkey = {};
bpf_skb_get_tunnel_key(skb, &tkey, sizeof(tkey), 0);
... lookup or redirect based on tkey ...
'struct bpf_tunnel_key' will be extended in the future by adding
elements to the end and the 'size' argument will indicate which fields
are populated, thereby keeping backwards compatibility.
The 'flags' argument may be used as well when the 'size' is not enough or
to indicate completely different layout of bpf_tunnel_key.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-30 16:36:57 -06:00
|
|
|
|
|
|
|
skb_dst_drop(skb);
|
|
|
|
dst_hold((struct dst_entry *) md);
|
|
|
|
skb_dst_set(skb, (struct dst_entry *) md);
|
|
|
|
|
|
|
|
info = &md->u.tun_info;
|
|
|
|
info->mode = IP_TUNNEL_INFO_TX;
|
2016-01-10 17:16:39 -07:00
|
|
|
|
bpf, vxlan, geneve, gre: fix usage of dst_cache on xmit
The assumptions from commit 0c1d70af924b ("net: use dst_cache for vxlan
device"), 468dfffcd762 ("geneve: add dst caching support") and 3c1cb4d2604c
("net/ipv4: add dst cache support for gre lwtunnels") on dst_cache usage
when ip_tunnel_info is used is unfortunately not always valid as assumed.
While it seems correct for ip_tunnel_info front-ends such as OVS, eBPF
however can fill in ip_tunnel_info for consumers like vxlan, geneve or gre
with different remote dsts, tos, etc, therefore they cannot be assumed as
packet independent.
Right now vxlan, geneve, gre would cache the dst for eBPF and every packet
would reuse the same entry that was first created on the initial route
lookup. eBPF doesn't store/cache the ip_tunnel_info, so each skb may have
a different one.
Fix it by adding a flag that checks the ip_tunnel_info. Also the !tos test
in vxlan needs to be handeled differently in this context as it is currently
inferred from ip_tunnel_info as well if present. ip_tunnel_dst_cache_usable()
helper is added for the three tunnel cases, which checks if we can use dst
cache.
Fixes: 0c1d70af924b ("net: use dst_cache for vxlan device")
Fixes: 468dfffcd762 ("geneve: add dst caching support")
Fixes: 3c1cb4d2604c ("net/ipv4: add dst cache support for gre lwtunnels")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-04 07:15:07 -07:00
|
|
|
info->key.tun_flags = TUNNEL_KEY | TUNNEL_CSUM | TUNNEL_NOCACHE;
|
2016-03-04 07:15:05 -07:00
|
|
|
if (flags & BPF_F_DONT_FRAGMENT)
|
|
|
|
info->key.tun_flags |= TUNNEL_DONT_FRAGMENT;
|
|
|
|
|
bpf: add helpers to access tunnel metadata
Introduce helpers to let eBPF programs attached to TC manipulate tunnel metadata:
bpf_skb_[gs]et_tunnel_key(skb, key, size, flags)
skb: pointer to skb
key: pointer to 'struct bpf_tunnel_key'
size: size of 'struct bpf_tunnel_key'
flags: room for future extensions
First eBPF program that uses these helpers will allocate per_cpu
metadata_dst structures that will be used on TX.
On RX metadata_dst is allocated by tunnel driver.
Typical usage for TX:
struct bpf_tunnel_key tkey;
... populate tkey ...
bpf_skb_set_tunnel_key(skb, &tkey, sizeof(tkey), 0);
bpf_clone_redirect(skb, vxlan_dev_ifindex, 0);
RX:
struct bpf_tunnel_key tkey = {};
bpf_skb_get_tunnel_key(skb, &tkey, sizeof(tkey), 0);
... lookup or redirect based on tkey ...
'struct bpf_tunnel_key' will be extended in the future by adding
elements to the end and the 'size' argument will indicate which fields
are populated, thereby keeping backwards compatibility.
The 'flags' argument may be used as well when the 'size' is not enough or
to indicate completely different layout of bpf_tunnel_key.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-30 16:36:57 -06:00
|
|
|
info->key.tun_id = cpu_to_be64(from->tunnel_id);
|
2016-01-10 17:16:39 -07:00
|
|
|
info->key.tos = from->tunnel_tos;
|
|
|
|
info->key.ttl = from->tunnel_ttl;
|
|
|
|
|
|
|
|
if (flags & BPF_F_TUNINFO_IPV6) {
|
|
|
|
info->mode |= IP_TUNNEL_INFO_IPV6;
|
|
|
|
memcpy(&info->key.u.ipv6.dst, from->remote_ipv6,
|
|
|
|
sizeof(from->remote_ipv6));
|
2016-03-08 19:00:05 -07:00
|
|
|
info->key.label = cpu_to_be32(from->tunnel_label) &
|
|
|
|
IPV6_FLOWLABEL_MASK;
|
2016-01-10 17:16:39 -07:00
|
|
|
} else {
|
|
|
|
info->key.u.ipv4.dst = cpu_to_be32(from->remote_ipv4);
|
2016-02-22 18:05:26 -07:00
|
|
|
if (flags & BPF_F_ZERO_CSUM_TX)
|
|
|
|
info->key.tun_flags &= ~TUNNEL_CSUM;
|
2016-01-10 17:16:39 -07:00
|
|
|
}
|
bpf: add helpers to access tunnel metadata
Introduce helpers to let eBPF programs attached to TC manipulate tunnel metadata:
bpf_skb_[gs]et_tunnel_key(skb, key, size, flags)
skb: pointer to skb
key: pointer to 'struct bpf_tunnel_key'
size: size of 'struct bpf_tunnel_key'
flags: room for future extensions
First eBPF program that uses these helpers will allocate per_cpu
metadata_dst structures that will be used on TX.
On RX metadata_dst is allocated by tunnel driver.
Typical usage for TX:
struct bpf_tunnel_key tkey;
... populate tkey ...
bpf_skb_set_tunnel_key(skb, &tkey, sizeof(tkey), 0);
bpf_clone_redirect(skb, vxlan_dev_ifindex, 0);
RX:
struct bpf_tunnel_key tkey = {};
bpf_skb_get_tunnel_key(skb, &tkey, sizeof(tkey), 0);
... lookup or redirect based on tkey ...
'struct bpf_tunnel_key' will be extended in the future by adding
elements to the end and the 'size' argument will indicate which fields
are populated, thereby keeping backwards compatibility.
The 'flags' argument may be used as well when the 'size' is not enough or
to indicate completely different layout of bpf_tunnel_key.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-30 16:36:57 -06:00
|
|
|
|
|
|
|
return 0;
|
|
|
|
}
|
|
|
|
|
2016-03-04 07:15:04 -07:00
|
|
|
static const struct bpf_func_proto bpf_skb_set_tunnel_key_proto = {
|
bpf: add helpers to access tunnel metadata
Introduce helpers to let eBPF programs attached to TC manipulate tunnel metadata:
bpf_skb_[gs]et_tunnel_key(skb, key, size, flags)
skb: pointer to skb
key: pointer to 'struct bpf_tunnel_key'
size: size of 'struct bpf_tunnel_key'
flags: room for future extensions
First eBPF program that uses these helpers will allocate per_cpu
metadata_dst structures that will be used on TX.
On RX metadata_dst is allocated by tunnel driver.
Typical usage for TX:
struct bpf_tunnel_key tkey;
... populate tkey ...
bpf_skb_set_tunnel_key(skb, &tkey, sizeof(tkey), 0);
bpf_clone_redirect(skb, vxlan_dev_ifindex, 0);
RX:
struct bpf_tunnel_key tkey = {};
bpf_skb_get_tunnel_key(skb, &tkey, sizeof(tkey), 0);
... lookup or redirect based on tkey ...
'struct bpf_tunnel_key' will be extended in the future by adding
elements to the end and the 'size' argument will indicate which fields
are populated, thereby keeping backwards compatibility.
The 'flags' argument may be used as well when the 'size' is not enough or
to indicate completely different layout of bpf_tunnel_key.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-30 16:36:57 -06:00
|
|
|
.func = bpf_skb_set_tunnel_key,
|
|
|
|
.gpl_only = false,
|
|
|
|
.ret_type = RET_INTEGER,
|
|
|
|
.arg1_type = ARG_PTR_TO_CTX,
|
|
|
|
.arg2_type = ARG_PTR_TO_STACK,
|
|
|
|
.arg3_type = ARG_CONST_STACK_SIZE,
|
|
|
|
.arg4_type = ARG_ANYTHING,
|
|
|
|
};
|
|
|
|
|
bpf: support for access to tunnel options
After eBPF being able to programmatically access/manage tunnel key meta
data via commit d3aa45ce6b94 ("bpf: add helpers to access tunnel metadata")
and more recently also for IPv6 through c6c33454072f ("bpf: support ipv6
for bpf_skb_{set,get}_tunnel_key"), this work adds two complementary
helpers to generically access their auxiliary tunnel options.
Geneve and vxlan support this facility. For geneve, TLVs can be pushed,
and for the vxlan case its GBP extension. I.e. setting tunnel key for geneve
case only makes sense, if we can also read/write TLVs into it. In the GBP
case, it provides the flexibility to easily map the group policy ID in
combination with other helpers or maps.
I chose to model this as two separate helpers, bpf_skb_{set,get}_tunnel_opt(),
for a couple of reasons. bpf_skb_{set,get}_tunnel_key() is already rather
complex by itself, and there may be cases for tunnel key backends where
tunnel options are not always needed. If we would have integrated this
into bpf_skb_{set,get}_tunnel_key() nevertheless, we are very limited with
remaining helper arguments, so keeping compatibility on structs in case of
passing in a flat buffer gets more cumbersome. Separating both also allows
for more flexibility and future extensibility, f.e. options could be fed
directly from a map, etc.
Moreover, change geneve's xmit path to test only for info->options_len
instead of TUNNEL_GENEVE_OPT flag. This makes it more consistent with vxlan's
xmit path and allows for avoiding to specify a protocol flag in the API on
xmit, so it can be protocol agnostic. Having info->options_len is enough
information that is needed. Tested with vxlan and geneve.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-04 07:15:06 -07:00
|
|
|
static u64 bpf_skb_set_tunnel_opt(u64 r1, u64 r2, u64 size, u64 r4, u64 r5)
|
|
|
|
{
|
|
|
|
struct sk_buff *skb = (struct sk_buff *) (long) r1;
|
|
|
|
u8 *from = (u8 *) (long) r2;
|
|
|
|
struct ip_tunnel_info *info = skb_tunnel_info(skb);
|
|
|
|
const struct metadata_dst *md = this_cpu_ptr(md_dst);
|
|
|
|
|
|
|
|
if (unlikely(info != &md->u.tun_info || (size & (sizeof(u32) - 1))))
|
|
|
|
return -EINVAL;
|
2016-03-15 18:42:51 -06:00
|
|
|
if (unlikely(size > IP_TUNNEL_OPTS_MAX))
|
bpf: support for access to tunnel options
After eBPF being able to programmatically access/manage tunnel key meta
data via commit d3aa45ce6b94 ("bpf: add helpers to access tunnel metadata")
and more recently also for IPv6 through c6c33454072f ("bpf: support ipv6
for bpf_skb_{set,get}_tunnel_key"), this work adds two complementary
helpers to generically access their auxiliary tunnel options.
Geneve and vxlan support this facility. For geneve, TLVs can be pushed,
and for the vxlan case its GBP extension. I.e. setting tunnel key for geneve
case only makes sense, if we can also read/write TLVs into it. In the GBP
case, it provides the flexibility to easily map the group policy ID in
combination with other helpers or maps.
I chose to model this as two separate helpers, bpf_skb_{set,get}_tunnel_opt(),
for a couple of reasons. bpf_skb_{set,get}_tunnel_key() is already rather
complex by itself, and there may be cases for tunnel key backends where
tunnel options are not always needed. If we would have integrated this
into bpf_skb_{set,get}_tunnel_key() nevertheless, we are very limited with
remaining helper arguments, so keeping compatibility on structs in case of
passing in a flat buffer gets more cumbersome. Separating both also allows
for more flexibility and future extensibility, f.e. options could be fed
directly from a map, etc.
Moreover, change geneve's xmit path to test only for info->options_len
instead of TUNNEL_GENEVE_OPT flag. This makes it more consistent with vxlan's
xmit path and allows for avoiding to specify a protocol flag in the API on
xmit, so it can be protocol agnostic. Having info->options_len is enough
information that is needed. Tested with vxlan and geneve.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-04 07:15:06 -07:00
|
|
|
return -ENOMEM;
|
|
|
|
|
|
|
|
ip_tunnel_info_opts_set(info, from, size);
|
|
|
|
|
|
|
|
return 0;
|
|
|
|
}
|
|
|
|
|
|
|
|
static const struct bpf_func_proto bpf_skb_set_tunnel_opt_proto = {
|
|
|
|
.func = bpf_skb_set_tunnel_opt,
|
|
|
|
.gpl_only = false,
|
|
|
|
.ret_type = RET_INTEGER,
|
|
|
|
.arg1_type = ARG_PTR_TO_CTX,
|
|
|
|
.arg2_type = ARG_PTR_TO_STACK,
|
|
|
|
.arg3_type = ARG_CONST_STACK_SIZE,
|
|
|
|
};
|
|
|
|
|
|
|
|
static const struct bpf_func_proto *
|
|
|
|
bpf_get_skb_set_tunnel_proto(enum bpf_func_id which)
|
bpf: add helpers to access tunnel metadata
Introduce helpers to let eBPF programs attached to TC manipulate tunnel metadata:
bpf_skb_[gs]et_tunnel_key(skb, key, size, flags)
skb: pointer to skb
key: pointer to 'struct bpf_tunnel_key'
size: size of 'struct bpf_tunnel_key'
flags: room for future extensions
First eBPF program that uses these helpers will allocate per_cpu
metadata_dst structures that will be used on TX.
On RX metadata_dst is allocated by tunnel driver.
Typical usage for TX:
struct bpf_tunnel_key tkey;
... populate tkey ...
bpf_skb_set_tunnel_key(skb, &tkey, sizeof(tkey), 0);
bpf_clone_redirect(skb, vxlan_dev_ifindex, 0);
RX:
struct bpf_tunnel_key tkey = {};
bpf_skb_get_tunnel_key(skb, &tkey, sizeof(tkey), 0);
... lookup or redirect based on tkey ...
'struct bpf_tunnel_key' will be extended in the future by adding
elements to the end and the 'size' argument will indicate which fields
are populated, thereby keeping backwards compatibility.
The 'flags' argument may be used as well when the 'size' is not enough or
to indicate completely different layout of bpf_tunnel_key.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-30 16:36:57 -06:00
|
|
|
{
|
|
|
|
if (!md_dst) {
|
bpf: support for access to tunnel options
After eBPF being able to programmatically access/manage tunnel key meta
data via commit d3aa45ce6b94 ("bpf: add helpers to access tunnel metadata")
and more recently also for IPv6 through c6c33454072f ("bpf: support ipv6
for bpf_skb_{set,get}_tunnel_key"), this work adds two complementary
helpers to generically access their auxiliary tunnel options.
Geneve and vxlan support this facility. For geneve, TLVs can be pushed,
and for the vxlan case its GBP extension. I.e. setting tunnel key for geneve
case only makes sense, if we can also read/write TLVs into it. In the GBP
case, it provides the flexibility to easily map the group policy ID in
combination with other helpers or maps.
I chose to model this as two separate helpers, bpf_skb_{set,get}_tunnel_opt(),
for a couple of reasons. bpf_skb_{set,get}_tunnel_key() is already rather
complex by itself, and there may be cases for tunnel key backends where
tunnel options are not always needed. If we would have integrated this
into bpf_skb_{set,get}_tunnel_key() nevertheless, we are very limited with
remaining helper arguments, so keeping compatibility on structs in case of
passing in a flat buffer gets more cumbersome. Separating both also allows
for more flexibility and future extensibility, f.e. options could be fed
directly from a map, etc.
Moreover, change geneve's xmit path to test only for info->options_len
instead of TUNNEL_GENEVE_OPT flag. This makes it more consistent with vxlan's
xmit path and allows for avoiding to specify a protocol flag in the API on
xmit, so it can be protocol agnostic. Having info->options_len is enough
information that is needed. Tested with vxlan and geneve.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-04 07:15:06 -07:00
|
|
|
/* Race is not possible, since it's called from verifier
|
|
|
|
* that is holding verifier mutex.
|
bpf: add helpers to access tunnel metadata
Introduce helpers to let eBPF programs attached to TC manipulate tunnel metadata:
bpf_skb_[gs]et_tunnel_key(skb, key, size, flags)
skb: pointer to skb
key: pointer to 'struct bpf_tunnel_key'
size: size of 'struct bpf_tunnel_key'
flags: room for future extensions
First eBPF program that uses these helpers will allocate per_cpu
metadata_dst structures that will be used on TX.
On RX metadata_dst is allocated by tunnel driver.
Typical usage for TX:
struct bpf_tunnel_key tkey;
... populate tkey ...
bpf_skb_set_tunnel_key(skb, &tkey, sizeof(tkey), 0);
bpf_clone_redirect(skb, vxlan_dev_ifindex, 0);
RX:
struct bpf_tunnel_key tkey = {};
bpf_skb_get_tunnel_key(skb, &tkey, sizeof(tkey), 0);
... lookup or redirect based on tkey ...
'struct bpf_tunnel_key' will be extended in the future by adding
elements to the end and the 'size' argument will indicate which fields
are populated, thereby keeping backwards compatibility.
The 'flags' argument may be used as well when the 'size' is not enough or
to indicate completely different layout of bpf_tunnel_key.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-30 16:36:57 -06:00
|
|
|
*/
|
2016-03-15 18:42:51 -06:00
|
|
|
md_dst = metadata_dst_alloc_percpu(IP_TUNNEL_OPTS_MAX,
|
bpf: support for access to tunnel options
After eBPF being able to programmatically access/manage tunnel key meta
data via commit d3aa45ce6b94 ("bpf: add helpers to access tunnel metadata")
and more recently also for IPv6 through c6c33454072f ("bpf: support ipv6
for bpf_skb_{set,get}_tunnel_key"), this work adds two complementary
helpers to generically access their auxiliary tunnel options.
Geneve and vxlan support this facility. For geneve, TLVs can be pushed,
and for the vxlan case its GBP extension. I.e. setting tunnel key for geneve
case only makes sense, if we can also read/write TLVs into it. In the GBP
case, it provides the flexibility to easily map the group policy ID in
combination with other helpers or maps.
I chose to model this as two separate helpers, bpf_skb_{set,get}_tunnel_opt(),
for a couple of reasons. bpf_skb_{set,get}_tunnel_key() is already rather
complex by itself, and there may be cases for tunnel key backends where
tunnel options are not always needed. If we would have integrated this
into bpf_skb_{set,get}_tunnel_key() nevertheless, we are very limited with
remaining helper arguments, so keeping compatibility on structs in case of
passing in a flat buffer gets more cumbersome. Separating both also allows
for more flexibility and future extensibility, f.e. options could be fed
directly from a map, etc.
Moreover, change geneve's xmit path to test only for info->options_len
instead of TUNNEL_GENEVE_OPT flag. This makes it more consistent with vxlan's
xmit path and allows for avoiding to specify a protocol flag in the API on
xmit, so it can be protocol agnostic. Having info->options_len is enough
information that is needed. Tested with vxlan and geneve.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-04 07:15:06 -07:00
|
|
|
GFP_KERNEL);
|
bpf: add helpers to access tunnel metadata
Introduce helpers to let eBPF programs attached to TC manipulate tunnel metadata:
bpf_skb_[gs]et_tunnel_key(skb, key, size, flags)
skb: pointer to skb
key: pointer to 'struct bpf_tunnel_key'
size: size of 'struct bpf_tunnel_key'
flags: room for future extensions
First eBPF program that uses these helpers will allocate per_cpu
metadata_dst structures that will be used on TX.
On RX metadata_dst is allocated by tunnel driver.
Typical usage for TX:
struct bpf_tunnel_key tkey;
... populate tkey ...
bpf_skb_set_tunnel_key(skb, &tkey, sizeof(tkey), 0);
bpf_clone_redirect(skb, vxlan_dev_ifindex, 0);
RX:
struct bpf_tunnel_key tkey = {};
bpf_skb_get_tunnel_key(skb, &tkey, sizeof(tkey), 0);
... lookup or redirect based on tkey ...
'struct bpf_tunnel_key' will be extended in the future by adding
elements to the end and the 'size' argument will indicate which fields
are populated, thereby keeping backwards compatibility.
The 'flags' argument may be used as well when the 'size' is not enough or
to indicate completely different layout of bpf_tunnel_key.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-30 16:36:57 -06:00
|
|
|
if (!md_dst)
|
|
|
|
return NULL;
|
|
|
|
}
|
bpf: support for access to tunnel options
After eBPF being able to programmatically access/manage tunnel key meta
data via commit d3aa45ce6b94 ("bpf: add helpers to access tunnel metadata")
and more recently also for IPv6 through c6c33454072f ("bpf: support ipv6
for bpf_skb_{set,get}_tunnel_key"), this work adds two complementary
helpers to generically access their auxiliary tunnel options.
Geneve and vxlan support this facility. For geneve, TLVs can be pushed,
and for the vxlan case its GBP extension. I.e. setting tunnel key for geneve
case only makes sense, if we can also read/write TLVs into it. In the GBP
case, it provides the flexibility to easily map the group policy ID in
combination with other helpers or maps.
I chose to model this as two separate helpers, bpf_skb_{set,get}_tunnel_opt(),
for a couple of reasons. bpf_skb_{set,get}_tunnel_key() is already rather
complex by itself, and there may be cases for tunnel key backends where
tunnel options are not always needed. If we would have integrated this
into bpf_skb_{set,get}_tunnel_key() nevertheless, we are very limited with
remaining helper arguments, so keeping compatibility on structs in case of
passing in a flat buffer gets more cumbersome. Separating both also allows
for more flexibility and future extensibility, f.e. options could be fed
directly from a map, etc.
Moreover, change geneve's xmit path to test only for info->options_len
instead of TUNNEL_GENEVE_OPT flag. This makes it more consistent with vxlan's
xmit path and allows for avoiding to specify a protocol flag in the API on
xmit, so it can be protocol agnostic. Having info->options_len is enough
information that is needed. Tested with vxlan and geneve.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-04 07:15:06 -07:00
|
|
|
|
|
|
|
switch (which) {
|
|
|
|
case BPF_FUNC_skb_set_tunnel_key:
|
|
|
|
return &bpf_skb_set_tunnel_key_proto;
|
|
|
|
case BPF_FUNC_skb_set_tunnel_opt:
|
|
|
|
return &bpf_skb_set_tunnel_opt_proto;
|
|
|
|
default:
|
|
|
|
return NULL;
|
|
|
|
}
|
bpf: add helpers to access tunnel metadata
Introduce helpers to let eBPF programs attached to TC manipulate tunnel metadata:
bpf_skb_[gs]et_tunnel_key(skb, key, size, flags)
skb: pointer to skb
key: pointer to 'struct bpf_tunnel_key'
size: size of 'struct bpf_tunnel_key'
flags: room for future extensions
First eBPF program that uses these helpers will allocate per_cpu
metadata_dst structures that will be used on TX.
On RX metadata_dst is allocated by tunnel driver.
Typical usage for TX:
struct bpf_tunnel_key tkey;
... populate tkey ...
bpf_skb_set_tunnel_key(skb, &tkey, sizeof(tkey), 0);
bpf_clone_redirect(skb, vxlan_dev_ifindex, 0);
RX:
struct bpf_tunnel_key tkey = {};
bpf_skb_get_tunnel_key(skb, &tkey, sizeof(tkey), 0);
... lookup or redirect based on tkey ...
'struct bpf_tunnel_key' will be extended in the future by adding
elements to the end and the 'size' argument will indicate which fields
are populated, thereby keeping backwards compatibility.
The 'flags' argument may be used as well when the 'size' is not enough or
to indicate completely different layout of bpf_tunnel_key.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-30 16:36:57 -06:00
|
|
|
}
|
|
|
|
|
2015-03-01 04:31:45 -07:00
|
|
|
static const struct bpf_func_proto *
|
|
|
|
sk_filter_func_proto(enum bpf_func_id func_id)
|
2014-12-01 16:06:35 -07:00
|
|
|
{
|
|
|
|
switch (func_id) {
|
|
|
|
case BPF_FUNC_map_lookup_elem:
|
|
|
|
return &bpf_map_lookup_elem_proto;
|
|
|
|
case BPF_FUNC_map_update_elem:
|
|
|
|
return &bpf_map_update_elem_proto;
|
|
|
|
case BPF_FUNC_map_delete_elem:
|
|
|
|
return &bpf_map_delete_elem_proto;
|
2015-03-13 19:27:16 -06:00
|
|
|
case BPF_FUNC_get_prandom_u32:
|
|
|
|
return &bpf_get_prandom_u32_proto;
|
2015-03-13 19:27:17 -06:00
|
|
|
case BPF_FUNC_get_smp_processor_id:
|
|
|
|
return &bpf_get_smp_processor_id_proto;
|
bpf: allow bpf programs to tail-call other bpf programs
introduce bpf_tail_call(ctx, &jmp_table, index) helper function
which can be used from BPF programs like:
int bpf_prog(struct pt_regs *ctx)
{
...
bpf_tail_call(ctx, &jmp_table, index);
...
}
that is roughly equivalent to:
int bpf_prog(struct pt_regs *ctx)
{
...
if (jmp_table[index])
return (*jmp_table[index])(ctx);
...
}
The important detail that it's not a normal call, but a tail call.
The kernel stack is precious, so this helper reuses the current
stack frame and jumps into another BPF program without adding
extra call frame.
It's trivially done in interpreter and a bit trickier in JITs.
In case of x64 JIT the bigger part of generated assembler prologue
is common for all programs, so it is simply skipped while jumping.
Other JITs can do similar prologue-skipping optimization or
do stack unwind before jumping into the next program.
bpf_tail_call() arguments:
ctx - context pointer
jmp_table - one of BPF_MAP_TYPE_PROG_ARRAY maps used as the jump table
index - index in the jump table
Since all BPF programs are idenitified by file descriptor, user space
need to populate the jmp_table with FDs of other BPF programs.
If jmp_table[index] is empty the bpf_tail_call() doesn't jump anywhere
and program execution continues as normal.
New BPF_MAP_TYPE_PROG_ARRAY map type is introduced so that user space can
populate this jmp_table array with FDs of other bpf programs.
Programs can share the same jmp_table array or use multiple jmp_tables.
The chain of tail calls can form unpredictable dynamic loops therefore
tail_call_cnt is used to limit the number of calls and currently is set to 32.
Use cases:
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
==========
- simplify complex programs by splitting them into a sequence of small programs
- dispatch routine
For tracing and future seccomp the program may be triggered on all system
calls, but processing of syscall arguments will be different. It's more
efficient to implement them as:
int syscall_entry(struct seccomp_data *ctx)
{
bpf_tail_call(ctx, &syscall_jmp_table, ctx->nr /* syscall number */);
... default: process unknown syscall ...
}
int sys_write_event(struct seccomp_data *ctx) {...}
int sys_read_event(struct seccomp_data *ctx) {...}
syscall_jmp_table[__NR_write] = sys_write_event;
syscall_jmp_table[__NR_read] = sys_read_event;
For networking the program may call into different parsers depending on
packet format, like:
int packet_parser(struct __sk_buff *skb)
{
... parse L2, L3 here ...
__u8 ipproto = load_byte(skb, ... offsetof(struct iphdr, protocol));
bpf_tail_call(skb, &ipproto_jmp_table, ipproto);
... default: process unknown protocol ...
}
int parse_tcp(struct __sk_buff *skb) {...}
int parse_udp(struct __sk_buff *skb) {...}
ipproto_jmp_table[IPPROTO_TCP] = parse_tcp;
ipproto_jmp_table[IPPROTO_UDP] = parse_udp;
- for TC use case, bpf_tail_call() allows to implement reclassify-like logic
- bpf_map_update_elem/delete calls into BPF_MAP_TYPE_PROG_ARRAY jump table
are atomic, so user space can build chains of BPF programs on the fly
Implementation details:
=======================
- high performance of bpf_tail_call() is the goal.
It could have been implemented without JIT changes as a wrapper on top of
BPF_PROG_RUN() macro, but with two downsides:
. all programs would have to pay performance penalty for this feature and
tail call itself would be slower, since mandatory stack unwind, return,
stack allocate would be done for every tailcall.
. tailcall would be limited to programs running preempt_disabled, since
generic 'void *ctx' doesn't have room for 'tail_call_cnt' and it would
need to be either global per_cpu variable accessed by helper and by wrapper
or global variable protected by locks.
In this implementation x64 JIT bypasses stack unwind and jumps into the
callee program after prologue.
- bpf_prog_array_compatible() ensures that prog_type of callee and caller
are the same and JITed/non-JITed flag is the same, since calling JITed
program from non-JITed is invalid, since stack frames are different.
Similarly calling kprobe type program from socket type program is invalid.
- jump table is implemented as BPF_MAP_TYPE_PROG_ARRAY to reuse 'map'
abstraction, its user space API and all of verifier logic.
It's in the existing arraymap.c file, since several functions are
shared with regular array map.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-19 17:59:03 -06:00
|
|
|
case BPF_FUNC_tail_call:
|
|
|
|
return &bpf_tail_call_proto;
|
2015-05-29 15:23:06 -06:00
|
|
|
case BPF_FUNC_ktime_get_ns:
|
|
|
|
return &bpf_ktime_get_ns_proto;
|
2015-06-12 20:39:13 -06:00
|
|
|
case BPF_FUNC_trace_printk:
|
bpf: enable non-root eBPF programs
In order to let unprivileged users load and execute eBPF programs
teach verifier to prevent pointer leaks.
Verifier will prevent
- any arithmetic on pointers
(except R10+Imm which is used to compute stack addresses)
- comparison of pointers
(except if (map_value_ptr == 0) ... )
- passing pointers to helper functions
- indirectly passing pointers in stack to helper functions
- returning pointer from bpf program
- storing pointers into ctx or maps
Spill/fill of pointers into stack is allowed, but mangling
of pointers stored in the stack or reading them byte by byte is not.
Within bpf programs the pointers do exist, since programs need to
be able to access maps, pass skb pointer to LD_ABS insns, etc
but programs cannot pass such pointer values to the outside
or obfuscate them.
Only allow BPF_PROG_TYPE_SOCKET_FILTER unprivileged programs,
so that socket filters (tcpdump), af_packet (quic acceleration)
and future kcm can use it.
tracing and tc cls/act program types still require root permissions,
since tracing actually needs to be able to see all kernel pointers
and tc is for root only.
For example, the following unprivileged socket filter program is allowed:
int bpf_prog1(struct __sk_buff *skb)
{
u32 index = load_byte(skb, ETH_HLEN + offsetof(struct iphdr, protocol));
u64 *value = bpf_map_lookup_elem(&my_map, &index);
if (value)
*value += skb->len;
return 0;
}
but the following program is not:
int bpf_prog1(struct __sk_buff *skb)
{
u32 index = load_byte(skb, ETH_HLEN + offsetof(struct iphdr, protocol));
u64 *value = bpf_map_lookup_elem(&my_map, &index);
if (value)
*value += (u64) skb;
return 0;
}
since it would leak the kernel address into the map.
Unprivileged socket filter bpf programs have access to the
following helper functions:
- map lookup/update/delete (but they cannot store kernel pointers into them)
- get_random (it's already exposed to unprivileged user space)
- get_smp_processor_id
- tail_call into another socket filter program
- ktime_get_ns
The feature is controlled by sysctl kernel.unprivileged_bpf_disabled.
This toggle defaults to off (0), but can be set true (1). Once true,
bpf programs and maps cannot be accessed from unprivileged process,
and the toggle cannot be set back to false.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-10-07 23:23:21 -06:00
|
|
|
if (capable(CAP_SYS_ADMIN))
|
|
|
|
return bpf_get_trace_printk_proto();
|
2014-12-01 16:06:35 -07:00
|
|
|
default:
|
|
|
|
return NULL;
|
|
|
|
}
|
|
|
|
}
|
|
|
|
|
2015-03-26 20:53:57 -06:00
|
|
|
static const struct bpf_func_proto *
|
|
|
|
tc_cls_act_func_proto(enum bpf_func_id func_id)
|
|
|
|
{
|
|
|
|
switch (func_id) {
|
|
|
|
case BPF_FUNC_skb_store_bytes:
|
|
|
|
return &bpf_skb_store_bytes_proto;
|
bpf: add bpf_skb_load_bytes helper
When hacking tc programs with eBPF, one of the issues that come up
from time to time is to load addresses from headers. In eBPF as in
classic BPF, we have BPF_LD | BPF_ABS | BPF_{B,H,W} instructions that
extract a byte, half-word or word out of the skb data though helpers
such as bpf_load_pointer() (interpreter case).
F.e. extracting a whole IPv6 address could possibly look like ...
union v6addr {
struct {
__u32 p1;
__u32 p2;
__u32 p3;
__u32 p4;
};
__u8 addr[16];
};
[...]
a.p1 = htonl(load_word(skb, off));
a.p2 = htonl(load_word(skb, off + 4));
a.p3 = htonl(load_word(skb, off + 8));
a.p4 = htonl(load_word(skb, off + 12));
[...]
/* access to a.addr[...] */
This work adds a complementary helper bpf_skb_load_bytes() (we also
have bpf_skb_store_bytes()) as an alternative where the same call
would look like from an eBPF program:
ret = bpf_skb_load_bytes(skb, off, addr, sizeof(addr));
Same verifier restrictions apply as in ffeedafbf023 ("bpf: introduce
current->pid, tgid, uid, gid, comm accessors") case, where stack memory
access needs to be statically verified and thus guaranteed to be
initialized in first use (otherwise verifier cannot tell whether a
subsequent access to it is valid or not as it's runtime dependent).
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-17 15:51:53 -07:00
|
|
|
case BPF_FUNC_skb_load_bytes:
|
|
|
|
return &bpf_skb_load_bytes_proto;
|
bpf: add generic bpf_csum_diff helper
For L4 checksums, we currently have bpf_l4_csum_replace() helper. It's
currently limited to handle 2 and 4 byte changes in a header and feeds the
from/to into inet_proto_csum_replace{2,4}() helpers of the kernel. When
working with IPv6, for example, this makes it rather cumbersome to deal
with, similarly when editing larger parts of a header.
Instead, extend the API in a more generic way: For bpf_l4_csum_replace(),
add a case for header field mask of 0 to change the checksum at a given
offset through inet_proto_csum_replace_by_diff(), and provide a helper
bpf_csum_diff() that can generically calculate a from/to diff for arbitrary
amounts of data.
This can be used in multiple ways: for the bpf_l4_csum_replace() only
part, this even provides us with the option to insert precalculated diffs
from user space f.e. from a map, or from bpf_csum_diff() during runtime.
bpf_csum_diff() has a optional from/to stack buffer input, so we can
calculate a diff by using a scratchbuffer for scenarios where we're
inserting (from is NULL), removing (to is NULL) or diffing (from/to buffers
don't need to be of equal size) data. Also, bpf_csum_diff() allows to
feed a previous csum into csum_partial(), so the function can also be
cascaded.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-02-19 15:05:23 -07:00
|
|
|
case BPF_FUNC_csum_diff:
|
|
|
|
return &bpf_csum_diff_proto;
|
2015-04-01 18:12:13 -06:00
|
|
|
case BPF_FUNC_l3_csum_replace:
|
|
|
|
return &bpf_l3_csum_replace_proto;
|
|
|
|
case BPF_FUNC_l4_csum_replace:
|
|
|
|
return &bpf_l4_csum_replace_proto;
|
2015-06-02 17:03:14 -06:00
|
|
|
case BPF_FUNC_clone_redirect:
|
|
|
|
return &bpf_clone_redirect_proto;
|
2015-07-15 06:21:42 -06:00
|
|
|
case BPF_FUNC_get_cgroup_classid:
|
|
|
|
return &bpf_get_cgroup_classid_proto;
|
2015-07-20 21:34:18 -06:00
|
|
|
case BPF_FUNC_skb_vlan_push:
|
|
|
|
return &bpf_skb_vlan_push_proto;
|
|
|
|
case BPF_FUNC_skb_vlan_pop:
|
|
|
|
return &bpf_skb_vlan_pop_proto;
|
bpf: add helpers to access tunnel metadata
Introduce helpers to let eBPF programs attached to TC manipulate tunnel metadata:
bpf_skb_[gs]et_tunnel_key(skb, key, size, flags)
skb: pointer to skb
key: pointer to 'struct bpf_tunnel_key'
size: size of 'struct bpf_tunnel_key'
flags: room for future extensions
First eBPF program that uses these helpers will allocate per_cpu
metadata_dst structures that will be used on TX.
On RX metadata_dst is allocated by tunnel driver.
Typical usage for TX:
struct bpf_tunnel_key tkey;
... populate tkey ...
bpf_skb_set_tunnel_key(skb, &tkey, sizeof(tkey), 0);
bpf_clone_redirect(skb, vxlan_dev_ifindex, 0);
RX:
struct bpf_tunnel_key tkey = {};
bpf_skb_get_tunnel_key(skb, &tkey, sizeof(tkey), 0);
... lookup or redirect based on tkey ...
'struct bpf_tunnel_key' will be extended in the future by adding
elements to the end and the 'size' argument will indicate which fields
are populated, thereby keeping backwards compatibility.
The 'flags' argument may be used as well when the 'size' is not enough or
to indicate completely different layout of bpf_tunnel_key.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-30 16:36:57 -06:00
|
|
|
case BPF_FUNC_skb_get_tunnel_key:
|
|
|
|
return &bpf_skb_get_tunnel_key_proto;
|
|
|
|
case BPF_FUNC_skb_set_tunnel_key:
|
bpf: support for access to tunnel options
After eBPF being able to programmatically access/manage tunnel key meta
data via commit d3aa45ce6b94 ("bpf: add helpers to access tunnel metadata")
and more recently also for IPv6 through c6c33454072f ("bpf: support ipv6
for bpf_skb_{set,get}_tunnel_key"), this work adds two complementary
helpers to generically access their auxiliary tunnel options.
Geneve and vxlan support this facility. For geneve, TLVs can be pushed,
and for the vxlan case its GBP extension. I.e. setting tunnel key for geneve
case only makes sense, if we can also read/write TLVs into it. In the GBP
case, it provides the flexibility to easily map the group policy ID in
combination with other helpers or maps.
I chose to model this as two separate helpers, bpf_skb_{set,get}_tunnel_opt(),
for a couple of reasons. bpf_skb_{set,get}_tunnel_key() is already rather
complex by itself, and there may be cases for tunnel key backends where
tunnel options are not always needed. If we would have integrated this
into bpf_skb_{set,get}_tunnel_key() nevertheless, we are very limited with
remaining helper arguments, so keeping compatibility on structs in case of
passing in a flat buffer gets more cumbersome. Separating both also allows
for more flexibility and future extensibility, f.e. options could be fed
directly from a map, etc.
Moreover, change geneve's xmit path to test only for info->options_len
instead of TUNNEL_GENEVE_OPT flag. This makes it more consistent with vxlan's
xmit path and allows for avoiding to specify a protocol flag in the API on
xmit, so it can be protocol agnostic. Having info->options_len is enough
information that is needed. Tested with vxlan and geneve.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-04 07:15:06 -07:00
|
|
|
return bpf_get_skb_set_tunnel_proto(func_id);
|
|
|
|
case BPF_FUNC_skb_get_tunnel_opt:
|
|
|
|
return &bpf_skb_get_tunnel_opt_proto;
|
|
|
|
case BPF_FUNC_skb_set_tunnel_opt:
|
|
|
|
return bpf_get_skb_set_tunnel_proto(func_id);
|
2015-09-16 00:05:43 -06:00
|
|
|
case BPF_FUNC_redirect:
|
|
|
|
return &bpf_redirect_proto;
|
2015-09-29 17:41:51 -06:00
|
|
|
case BPF_FUNC_get_route_realm:
|
|
|
|
return &bpf_get_route_realm_proto;
|
bpf: add event output helper for notifications/sampling/logging
This patch adds a new helper for cls/act programs that can push events
to user space applications. For networking, this can be f.e. for sampling,
debugging, logging purposes or pushing of arbitrary wake-up events. The
idea is similar to a43eec304259 ("bpf: introduce bpf_perf_event_output()
helper") and 39111695b1b8 ("samples: bpf: add bpf_perf_event_output example").
The eBPF program utilizes a perf event array map that user space populates
with fds from perf_event_open(), the eBPF program calls into the helper
f.e. as skb_event_output(skb, &my_map, BPF_F_CURRENT_CPU, raw, sizeof(raw))
so that the raw data is pushed into the fd f.e. at the map index of the
current CPU.
User space can poll/mmap/etc on this and has a data channel for receiving
events that can be post-processed. The nice thing is that since the eBPF
program and user space application making use of it are tightly coupled,
they can define their own arbitrary raw data format and what/when they
want to push.
While f.e. packet headers could be one part of the meta data that is being
pushed, this is not a substitute for things like packet sockets as whole
packet is not being pushed and push is only done in a single direction.
Intention is more of a generically usable, efficient event pipe to applications.
Workflow is that tc can pin the map and applications can attach themselves
e.g. after cls/act setup to one or multiple map slots, demuxing is done by
the eBPF program.
Adding this facility is with minimal effort, it reuses the helper
introduced in a43eec304259 ("bpf: introduce bpf_perf_event_output() helper")
and we get its functionality for free by overloading its BPF_FUNC_ identifier
for cls/act programs, ctx is currently unused, but will be made use of in
future. Example will be added to iproute2's BPF example files.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-04-18 13:01:24 -06:00
|
|
|
case BPF_FUNC_perf_event_output:
|
|
|
|
return bpf_get_event_output_proto();
|
2015-03-26 20:53:57 -06:00
|
|
|
default:
|
|
|
|
return sk_filter_func_proto(func_id);
|
|
|
|
}
|
|
|
|
}
|
|
|
|
|
2015-06-04 11:11:54 -06:00
|
|
|
static bool __is_valid_access(int off, int size, enum bpf_access_type type)
|
2014-12-01 16:06:35 -07:00
|
|
|
{
|
2015-03-13 12:57:42 -06:00
|
|
|
if (off < 0 || off >= sizeof(struct __sk_buff))
|
|
|
|
return false;
|
2016-05-13 11:08:26 -06:00
|
|
|
/* The verifier guarantees that size > 0. */
|
2015-03-13 12:57:42 -06:00
|
|
|
if (off % size != 0)
|
|
|
|
return false;
|
2016-05-13 11:08:26 -06:00
|
|
|
if (size != sizeof(__u32))
|
2015-03-13 12:57:42 -06:00
|
|
|
return false;
|
|
|
|
|
|
|
|
return true;
|
|
|
|
}
|
|
|
|
|
2015-06-04 11:11:54 -06:00
|
|
|
static bool sk_filter_is_valid_access(int off, int size,
|
|
|
|
enum bpf_access_type type)
|
|
|
|
{
|
2016-05-05 20:49:12 -06:00
|
|
|
switch (off) {
|
|
|
|
case offsetof(struct __sk_buff, tc_classid):
|
|
|
|
case offsetof(struct __sk_buff, data):
|
|
|
|
case offsetof(struct __sk_buff, data_end):
|
2015-09-16 00:05:42 -06:00
|
|
|
return false;
|
2016-05-05 20:49:12 -06:00
|
|
|
}
|
2015-09-16 00:05:42 -06:00
|
|
|
|
2015-06-04 11:11:54 -06:00
|
|
|
if (type == BPF_WRITE) {
|
|
|
|
switch (off) {
|
|
|
|
case offsetof(struct __sk_buff, cb[0]) ...
|
2016-05-13 11:08:26 -06:00
|
|
|
offsetof(struct __sk_buff, cb[4]):
|
2015-06-04 11:11:54 -06:00
|
|
|
break;
|
|
|
|
default:
|
|
|
|
return false;
|
|
|
|
}
|
|
|
|
}
|
|
|
|
|
|
|
|
return __is_valid_access(off, size, type);
|
|
|
|
}
|
|
|
|
|
|
|
|
static bool tc_cls_act_is_valid_access(int off, int size,
|
|
|
|
enum bpf_access_type type)
|
|
|
|
{
|
|
|
|
if (type == BPF_WRITE) {
|
|
|
|
switch (off) {
|
|
|
|
case offsetof(struct __sk_buff, mark):
|
|
|
|
case offsetof(struct __sk_buff, tc_index):
|
2015-09-29 17:41:52 -06:00
|
|
|
case offsetof(struct __sk_buff, priority):
|
2015-06-04 11:11:54 -06:00
|
|
|
case offsetof(struct __sk_buff, cb[0]) ...
|
2016-03-15 18:42:49 -06:00
|
|
|
offsetof(struct __sk_buff, cb[4]):
|
|
|
|
case offsetof(struct __sk_buff, tc_classid):
|
2015-06-04 11:11:54 -06:00
|
|
|
break;
|
|
|
|
default:
|
|
|
|
return false;
|
|
|
|
}
|
|
|
|
}
|
|
|
|
return __is_valid_access(off, size, type);
|
|
|
|
}
|
|
|
|
|
|
|
|
static u32 bpf_net_convert_ctx_access(enum bpf_access_type type, int dst_reg,
|
|
|
|
int src_reg, int ctx_off,
|
2015-10-07 11:55:41 -06:00
|
|
|
struct bpf_insn *insn_buf,
|
|
|
|
struct bpf_prog *prog)
|
2015-03-13 12:57:42 -06:00
|
|
|
{
|
|
|
|
struct bpf_insn *insn = insn_buf;
|
|
|
|
|
|
|
|
switch (ctx_off) {
|
|
|
|
case offsetof(struct __sk_buff, len):
|
|
|
|
BUILD_BUG_ON(FIELD_SIZEOF(struct sk_buff, len) != 4);
|
|
|
|
|
|
|
|
*insn++ = BPF_LDX_MEM(BPF_W, dst_reg, src_reg,
|
|
|
|
offsetof(struct sk_buff, len));
|
|
|
|
break;
|
|
|
|
|
2015-03-19 12:38:27 -06:00
|
|
|
case offsetof(struct __sk_buff, protocol):
|
|
|
|
BUILD_BUG_ON(FIELD_SIZEOF(struct sk_buff, protocol) != 2);
|
|
|
|
|
|
|
|
*insn++ = BPF_LDX_MEM(BPF_H, dst_reg, src_reg,
|
|
|
|
offsetof(struct sk_buff, protocol));
|
|
|
|
break;
|
|
|
|
|
2015-03-24 07:48:41 -06:00
|
|
|
case offsetof(struct __sk_buff, vlan_proto):
|
|
|
|
BUILD_BUG_ON(FIELD_SIZEOF(struct sk_buff, vlan_proto) != 2);
|
|
|
|
|
|
|
|
*insn++ = BPF_LDX_MEM(BPF_H, dst_reg, src_reg,
|
|
|
|
offsetof(struct sk_buff, vlan_proto));
|
|
|
|
break;
|
|
|
|
|
2015-04-03 12:52:24 -06:00
|
|
|
case offsetof(struct __sk_buff, priority):
|
|
|
|
BUILD_BUG_ON(FIELD_SIZEOF(struct sk_buff, priority) != 4);
|
|
|
|
|
2015-09-29 17:41:52 -06:00
|
|
|
if (type == BPF_WRITE)
|
|
|
|
*insn++ = BPF_STX_MEM(BPF_W, dst_reg, src_reg,
|
|
|
|
offsetof(struct sk_buff, priority));
|
|
|
|
else
|
|
|
|
*insn++ = BPF_LDX_MEM(BPF_W, dst_reg, src_reg,
|
|
|
|
offsetof(struct sk_buff, priority));
|
2015-04-03 12:52:24 -06:00
|
|
|
break;
|
|
|
|
|
2015-05-27 16:30:39 -06:00
|
|
|
case offsetof(struct __sk_buff, ingress_ifindex):
|
|
|
|
BUILD_BUG_ON(FIELD_SIZEOF(struct sk_buff, skb_iif) != 4);
|
|
|
|
|
|
|
|
*insn++ = BPF_LDX_MEM(BPF_W, dst_reg, src_reg,
|
|
|
|
offsetof(struct sk_buff, skb_iif));
|
|
|
|
break;
|
|
|
|
|
|
|
|
case offsetof(struct __sk_buff, ifindex):
|
|
|
|
BUILD_BUG_ON(FIELD_SIZEOF(struct net_device, ifindex) != 4);
|
|
|
|
|
|
|
|
*insn++ = BPF_LDX_MEM(bytes_to_bpf_size(FIELD_SIZEOF(struct sk_buff, dev)),
|
|
|
|
dst_reg, src_reg,
|
|
|
|
offsetof(struct sk_buff, dev));
|
|
|
|
*insn++ = BPF_JMP_IMM(BPF_JEQ, dst_reg, 0, 1);
|
|
|
|
*insn++ = BPF_LDX_MEM(BPF_W, dst_reg, dst_reg,
|
|
|
|
offsetof(struct net_device, ifindex));
|
|
|
|
break;
|
|
|
|
|
ebpf: add skb->hash to offset map for usage in {cls, act}_bpf or filters
Add skb->hash to the __sk_buff offset map, so it can be accessed from
an eBPF program. We currently already do this for classic BPF filters,
but not yet on eBPF, it might be useful as a demuxer in combination with
helpers like bpf_clone_redirect(), toy example:
__section("cls-lb") int ingress_main(struct __sk_buff *skb)
{
unsigned int which = 3 + (skb->hash & 7);
/* bpf_skb_store_bytes(skb, ...); */
/* bpf_l{3,4}_csum_replace(skb, ...); */
bpf_clone_redirect(skb, which, 0);
return -1;
}
I was thinking whether to add skb_get_hash(), but then concluded the
raw skb->hash seems fine in this case: we can directly access the hash
w/o extra eBPF helper function call, it's filled out by many NICs on
ingress, and in case the entropy level would not be sufficient, people
can still implement their own specific sw fallback hash mix anyway.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-31 16:46:29 -06:00
|
|
|
case offsetof(struct __sk_buff, hash):
|
|
|
|
BUILD_BUG_ON(FIELD_SIZEOF(struct sk_buff, hash) != 4);
|
|
|
|
|
|
|
|
*insn++ = BPF_LDX_MEM(BPF_W, dst_reg, src_reg,
|
|
|
|
offsetof(struct sk_buff, hash));
|
|
|
|
break;
|
|
|
|
|
2015-03-13 12:57:42 -06:00
|
|
|
case offsetof(struct __sk_buff, mark):
|
2015-06-04 11:11:54 -06:00
|
|
|
BUILD_BUG_ON(FIELD_SIZEOF(struct sk_buff, mark) != 4);
|
|
|
|
|
|
|
|
if (type == BPF_WRITE)
|
|
|
|
*insn++ = BPF_STX_MEM(BPF_W, dst_reg, src_reg,
|
|
|
|
offsetof(struct sk_buff, mark));
|
|
|
|
else
|
|
|
|
*insn++ = BPF_LDX_MEM(BPF_W, dst_reg, src_reg,
|
|
|
|
offsetof(struct sk_buff, mark));
|
|
|
|
break;
|
2015-03-13 12:57:42 -06:00
|
|
|
|
|
|
|
case offsetof(struct __sk_buff, pkt_type):
|
|
|
|
return convert_skb_access(SKF_AD_PKTTYPE, dst_reg, src_reg, insn);
|
|
|
|
|
|
|
|
case offsetof(struct __sk_buff, queue_mapping):
|
|
|
|
return convert_skb_access(SKF_AD_QUEUE, dst_reg, src_reg, insn);
|
2015-03-16 19:06:02 -06:00
|
|
|
|
|
|
|
case offsetof(struct __sk_buff, vlan_present):
|
|
|
|
return convert_skb_access(SKF_AD_VLAN_TAG_PRESENT,
|
|
|
|
dst_reg, src_reg, insn);
|
|
|
|
|
|
|
|
case offsetof(struct __sk_buff, vlan_tci):
|
|
|
|
return convert_skb_access(SKF_AD_VLAN_TAG,
|
|
|
|
dst_reg, src_reg, insn);
|
2015-06-04 11:11:54 -06:00
|
|
|
|
|
|
|
case offsetof(struct __sk_buff, cb[0]) ...
|
|
|
|
offsetof(struct __sk_buff, cb[4]):
|
|
|
|
BUILD_BUG_ON(FIELD_SIZEOF(struct qdisc_skb_cb, data) < 20);
|
|
|
|
|
2015-10-07 11:55:41 -06:00
|
|
|
prog->cb_access = 1;
|
2015-06-04 11:11:54 -06:00
|
|
|
ctx_off -= offsetof(struct __sk_buff, cb[0]);
|
|
|
|
ctx_off += offsetof(struct sk_buff, cb);
|
|
|
|
ctx_off += offsetof(struct qdisc_skb_cb, data);
|
|
|
|
if (type == BPF_WRITE)
|
|
|
|
*insn++ = BPF_STX_MEM(BPF_W, dst_reg, src_reg, ctx_off);
|
|
|
|
else
|
|
|
|
*insn++ = BPF_LDX_MEM(BPF_W, dst_reg, src_reg, ctx_off);
|
|
|
|
break;
|
|
|
|
|
2015-09-16 00:05:42 -06:00
|
|
|
case offsetof(struct __sk_buff, tc_classid):
|
|
|
|
ctx_off -= offsetof(struct __sk_buff, tc_classid);
|
|
|
|
ctx_off += offsetof(struct sk_buff, cb);
|
|
|
|
ctx_off += offsetof(struct qdisc_skb_cb, tc_classid);
|
2016-03-15 18:42:49 -06:00
|
|
|
if (type == BPF_WRITE)
|
|
|
|
*insn++ = BPF_STX_MEM(BPF_H, dst_reg, src_reg, ctx_off);
|
|
|
|
else
|
|
|
|
*insn++ = BPF_LDX_MEM(BPF_H, dst_reg, src_reg, ctx_off);
|
2015-09-16 00:05:42 -06:00
|
|
|
break;
|
|
|
|
|
2016-05-05 20:49:12 -06:00
|
|
|
case offsetof(struct __sk_buff, data):
|
|
|
|
*insn++ = BPF_LDX_MEM(bytes_to_bpf_size(FIELD_SIZEOF(struct sk_buff, data)),
|
|
|
|
dst_reg, src_reg,
|
|
|
|
offsetof(struct sk_buff, data));
|
|
|
|
break;
|
|
|
|
|
|
|
|
case offsetof(struct __sk_buff, data_end):
|
|
|
|
ctx_off -= offsetof(struct __sk_buff, data_end);
|
|
|
|
ctx_off += offsetof(struct sk_buff, cb);
|
|
|
|
ctx_off += offsetof(struct bpf_skb_data_end, data_end);
|
|
|
|
*insn++ = BPF_LDX_MEM(bytes_to_bpf_size(sizeof(void *)),
|
|
|
|
dst_reg, src_reg, ctx_off);
|
|
|
|
break;
|
|
|
|
|
2015-06-04 11:11:54 -06:00
|
|
|
case offsetof(struct __sk_buff, tc_index):
|
|
|
|
#ifdef CONFIG_NET_SCHED
|
|
|
|
BUILD_BUG_ON(FIELD_SIZEOF(struct sk_buff, tc_index) != 2);
|
|
|
|
|
|
|
|
if (type == BPF_WRITE)
|
|
|
|
*insn++ = BPF_STX_MEM(BPF_H, dst_reg, src_reg,
|
|
|
|
offsetof(struct sk_buff, tc_index));
|
|
|
|
else
|
|
|
|
*insn++ = BPF_LDX_MEM(BPF_H, dst_reg, src_reg,
|
|
|
|
offsetof(struct sk_buff, tc_index));
|
|
|
|
break;
|
|
|
|
#else
|
|
|
|
if (type == BPF_WRITE)
|
|
|
|
*insn++ = BPF_MOV64_REG(dst_reg, dst_reg);
|
|
|
|
else
|
|
|
|
*insn++ = BPF_MOV64_IMM(dst_reg, 0);
|
|
|
|
break;
|
|
|
|
#endif
|
2015-03-13 12:57:42 -06:00
|
|
|
}
|
|
|
|
|
|
|
|
return insn - insn_buf;
|
2014-12-01 16:06:35 -07:00
|
|
|
}
|
|
|
|
|
2015-03-01 04:31:45 -07:00
|
|
|
static const struct bpf_verifier_ops sk_filter_ops = {
|
2016-05-13 11:08:26 -06:00
|
|
|
.get_func_proto = sk_filter_func_proto,
|
|
|
|
.is_valid_access = sk_filter_is_valid_access,
|
|
|
|
.convert_ctx_access = bpf_net_convert_ctx_access,
|
2014-12-01 16:06:35 -07:00
|
|
|
};
|
|
|
|
|
2015-03-26 20:53:57 -06:00
|
|
|
static const struct bpf_verifier_ops tc_cls_act_ops = {
|
2016-05-13 11:08:26 -06:00
|
|
|
.get_func_proto = tc_cls_act_func_proto,
|
|
|
|
.is_valid_access = tc_cls_act_is_valid_access,
|
|
|
|
.convert_ctx_access = bpf_net_convert_ctx_access,
|
2015-03-26 20:53:57 -06:00
|
|
|
};
|
|
|
|
|
2015-03-01 04:31:45 -07:00
|
|
|
static struct bpf_prog_type_list sk_filter_type __read_mostly = {
|
2016-05-13 11:08:26 -06:00
|
|
|
.ops = &sk_filter_ops,
|
|
|
|
.type = BPF_PROG_TYPE_SOCKET_FILTER,
|
2014-12-01 16:06:35 -07:00
|
|
|
};
|
|
|
|
|
ebpf: add sched_cls_type and map it to sk_filter's verifier ops
As discussed recently and at netconf/netdev01, we want to prevent making
bpf_verifier_ops registration available for modules, but have them at a
controlled place inside the kernel instead.
The reason for this is, that out-of-tree modules can go crazy and define
and register any verfifier ops they want, doing all sorts of crap, even
bypassing available GPLed eBPF helper functions. We don't want to offer
such a shiny playground, of course, but keep strict control to ourselves
inside the core kernel.
This also encourages us to design eBPF user helpers carefully and
generically, so they can be shared among various subsystems using eBPF.
For the eBPF traffic classifier (cls_bpf), it's a good start to share
the same helper facilities as we currently do in eBPF for socket filters.
That way, we have BPF_PROG_TYPE_SCHED_CLS look like it's own type, thus
one day if there's a good reason to diverge the set of helper functions
from the set available to socket filters, we keep ABI compatibility.
In future, we could place all bpf_prog_type_list at a central place,
perhaps.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-01 04:31:46 -07:00
|
|
|
static struct bpf_prog_type_list sched_cls_type __read_mostly = {
|
2016-05-13 11:08:26 -06:00
|
|
|
.ops = &tc_cls_act_ops,
|
|
|
|
.type = BPF_PROG_TYPE_SCHED_CLS,
|
ebpf: add sched_cls_type and map it to sk_filter's verifier ops
As discussed recently and at netconf/netdev01, we want to prevent making
bpf_verifier_ops registration available for modules, but have them at a
controlled place inside the kernel instead.
The reason for this is, that out-of-tree modules can go crazy and define
and register any verfifier ops they want, doing all sorts of crap, even
bypassing available GPLed eBPF helper functions. We don't want to offer
such a shiny playground, of course, but keep strict control to ourselves
inside the core kernel.
This also encourages us to design eBPF user helpers carefully and
generically, so they can be shared among various subsystems using eBPF.
For the eBPF traffic classifier (cls_bpf), it's a good start to share
the same helper facilities as we currently do in eBPF for socket filters.
That way, we have BPF_PROG_TYPE_SCHED_CLS look like it's own type, thus
one day if there's a good reason to diverge the set of helper functions
from the set available to socket filters, we keep ABI compatibility.
In future, we could place all bpf_prog_type_list at a central place,
perhaps.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-01 04:31:46 -07:00
|
|
|
};
|
|
|
|
|
2015-03-20 08:11:11 -06:00
|
|
|
static struct bpf_prog_type_list sched_act_type __read_mostly = {
|
2016-05-13 11:08:26 -06:00
|
|
|
.ops = &tc_cls_act_ops,
|
|
|
|
.type = BPF_PROG_TYPE_SCHED_ACT,
|
2015-03-20 08:11:11 -06:00
|
|
|
};
|
|
|
|
|
2015-03-01 04:31:45 -07:00
|
|
|
static int __init register_sk_filter_ops(void)
|
2014-12-01 16:06:35 -07:00
|
|
|
{
|
2015-03-01 04:31:45 -07:00
|
|
|
bpf_register_prog_type(&sk_filter_type);
|
ebpf: add sched_cls_type and map it to sk_filter's verifier ops
As discussed recently and at netconf/netdev01, we want to prevent making
bpf_verifier_ops registration available for modules, but have them at a
controlled place inside the kernel instead.
The reason for this is, that out-of-tree modules can go crazy and define
and register any verfifier ops they want, doing all sorts of crap, even
bypassing available GPLed eBPF helper functions. We don't want to offer
such a shiny playground, of course, but keep strict control to ourselves
inside the core kernel.
This also encourages us to design eBPF user helpers carefully and
generically, so they can be shared among various subsystems using eBPF.
For the eBPF traffic classifier (cls_bpf), it's a good start to share
the same helper facilities as we currently do in eBPF for socket filters.
That way, we have BPF_PROG_TYPE_SCHED_CLS look like it's own type, thus
one day if there's a good reason to diverge the set of helper functions
from the set available to socket filters, we keep ABI compatibility.
In future, we could place all bpf_prog_type_list at a central place,
perhaps.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-01 04:31:46 -07:00
|
|
|
bpf_register_prog_type(&sched_cls_type);
|
2015-03-20 08:11:11 -06:00
|
|
|
bpf_register_prog_type(&sched_act_type);
|
ebpf: add sched_cls_type and map it to sk_filter's verifier ops
As discussed recently and at netconf/netdev01, we want to prevent making
bpf_verifier_ops registration available for modules, but have them at a
controlled place inside the kernel instead.
The reason for this is, that out-of-tree modules can go crazy and define
and register any verfifier ops they want, doing all sorts of crap, even
bypassing available GPLed eBPF helper functions. We don't want to offer
such a shiny playground, of course, but keep strict control to ourselves
inside the core kernel.
This also encourages us to design eBPF user helpers carefully and
generically, so they can be shared among various subsystems using eBPF.
For the eBPF traffic classifier (cls_bpf), it's a good start to share
the same helper facilities as we currently do in eBPF for socket filters.
That way, we have BPF_PROG_TYPE_SCHED_CLS look like it's own type, thus
one day if there's a good reason to diverge the set of helper functions
from the set available to socket filters, we keep ABI compatibility.
In future, we could place all bpf_prog_type_list at a central place,
perhaps.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-01 04:31:46 -07:00
|
|
|
|
2014-12-01 16:06:35 -07:00
|
|
|
return 0;
|
|
|
|
}
|
2015-03-01 04:31:45 -07:00
|
|
|
late_initcall(register_sk_filter_ops);
|
|
|
|
|
2016-04-05 09:10:16 -06:00
|
|
|
int sk_detach_filter(struct sock *sk)
|
2007-10-17 22:21:26 -06:00
|
|
|
{
|
|
|
|
int ret = -ENOENT;
|
|
|
|
struct sk_filter *filter;
|
|
|
|
|
2013-01-16 14:55:49 -07:00
|
|
|
if (sock_flag(sk, SOCK_FILTER_LOCKED))
|
|
|
|
return -EPERM;
|
|
|
|
|
2016-04-05 09:10:16 -06:00
|
|
|
filter = rcu_dereference_protected(sk->sk_filter,
|
|
|
|
lockdep_sock_is_held(sk));
|
2007-10-17 22:21:26 -06:00
|
|
|
if (filter) {
|
2011-08-01 10:19:00 -06:00
|
|
|
RCU_INIT_POINTER(sk->sk_filter, NULL);
|
2010-12-06 10:29:43 -07:00
|
|
|
sk_filter_uncharge(sk, filter);
|
2007-10-17 22:21:26 -06:00
|
|
|
ret = 0;
|
|
|
|
}
|
net: filter: keep original BPF program around
In order to open up the possibility to internally transform a BPF program
into an alternative and possibly non-trivial reversible representation, we
need to keep the original BPF program around, so that it can be passed back
to user space w/o the need of a complex decoder.
The reason for that use case resides in commit a8fc92778080 ("sk-filter:
Add ability to get socket filter program (v2)"), that is, the ability
to retrieve the currently attached BPF filter from a given socket used
mainly by the checkpoint-restore project, for example.
Therefore, we add two helpers sk_{store,release}_orig_filter for taking
care of that. In the sk_unattached_filter_create() case, there's no such
possibility/requirement to retrieve a loaded BPF program. Therefore, we
can spare us the work in that case.
This approach will simplify and slightly speed up both, sk_get_filter()
and sock_diag_put_filterinfo() handlers as we won't need to successively
decode filters anymore through sk_decode_filter(). As we still need
sk_decode_filter() later on, we're keeping it around.
Joint work with Alexei Starovoitov.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:19 -06:00
|
|
|
|
2007-10-17 22:21:26 -06:00
|
|
|
return ret;
|
|
|
|
}
|
2016-04-05 09:10:16 -06:00
|
|
|
EXPORT_SYMBOL_GPL(sk_detach_filter);
|
sk-filter: Add ability to get socket filter program (v2)
The SO_ATTACH_FILTER option is set only. I propose to add the get
ability by using SO_ATTACH_FILTER in getsockopt. To be less
irritating to eyes the SO_GET_FILTER alias to it is declared. This
ability is required by checkpoint-restore project to be able to
save full state of a socket.
There are two issues with getting filter back.
First, kernel modifies the sock_filter->code on filter load, thus in
order to return the filter element back to user we have to decode it
into user-visible constants. Fortunately the modification in question
is interconvertible.
Second, the BPF_S_ALU_DIV_K code modifies the command argument k to
speed up the run-time division by doing kernel_k = reciprocal(user_k).
Bad news is that different user_k may result in same kernel_k, so we
can't get the original user_k back. Good news is that we don't have
to do it. What we need to is calculate a user2_k so, that
reciprocal(user2_k) == reciprocal(user_k) == kernel_k
i.e. if it's re-loaded back the compiled again value will be exactly
the same as it was. That said, the user2_k can be calculated like this
user2_k = reciprocal(kernel_k)
with an exception, that if kernel_k == 0, then user2_k == 1.
The optlen argument is treated like this -- when zero, kernel returns
the amount of sock_fprog elements in filter, otherwise it should be
large enough for the sock_fprog array.
changes since v1:
* Declared SO_GET_FILTER in all arch headers
* Added decode of vlan-tag codes
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-10-31 20:01:48 -06:00
|
|
|
|
net: filter: keep original BPF program around
In order to open up the possibility to internally transform a BPF program
into an alternative and possibly non-trivial reversible representation, we
need to keep the original BPF program around, so that it can be passed back
to user space w/o the need of a complex decoder.
The reason for that use case resides in commit a8fc92778080 ("sk-filter:
Add ability to get socket filter program (v2)"), that is, the ability
to retrieve the currently attached BPF filter from a given socket used
mainly by the checkpoint-restore project, for example.
Therefore, we add two helpers sk_{store,release}_orig_filter for taking
care of that. In the sk_unattached_filter_create() case, there's no such
possibility/requirement to retrieve a loaded BPF program. Therefore, we
can spare us the work in that case.
This approach will simplify and slightly speed up both, sk_get_filter()
and sock_diag_put_filterinfo() handlers as we won't need to successively
decode filters anymore through sk_decode_filter(). As we still need
sk_decode_filter() later on, we're keeping it around.
Joint work with Alexei Starovoitov.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:19 -06:00
|
|
|
int sk_get_filter(struct sock *sk, struct sock_filter __user *ubuf,
|
|
|
|
unsigned int len)
|
sk-filter: Add ability to get socket filter program (v2)
The SO_ATTACH_FILTER option is set only. I propose to add the get
ability by using SO_ATTACH_FILTER in getsockopt. To be less
irritating to eyes the SO_GET_FILTER alias to it is declared. This
ability is required by checkpoint-restore project to be able to
save full state of a socket.
There are two issues with getting filter back.
First, kernel modifies the sock_filter->code on filter load, thus in
order to return the filter element back to user we have to decode it
into user-visible constants. Fortunately the modification in question
is interconvertible.
Second, the BPF_S_ALU_DIV_K code modifies the command argument k to
speed up the run-time division by doing kernel_k = reciprocal(user_k).
Bad news is that different user_k may result in same kernel_k, so we
can't get the original user_k back. Good news is that we don't have
to do it. What we need to is calculate a user2_k so, that
reciprocal(user2_k) == reciprocal(user_k) == kernel_k
i.e. if it's re-loaded back the compiled again value will be exactly
the same as it was. That said, the user2_k can be calculated like this
user2_k = reciprocal(kernel_k)
with an exception, that if kernel_k == 0, then user2_k == 1.
The optlen argument is treated like this -- when zero, kernel returns
the amount of sock_fprog elements in filter, otherwise it should be
large enough for the sock_fprog array.
changes since v1:
* Declared SO_GET_FILTER in all arch headers
* Added decode of vlan-tag codes
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-10-31 20:01:48 -06:00
|
|
|
{
|
net: filter: keep original BPF program around
In order to open up the possibility to internally transform a BPF program
into an alternative and possibly non-trivial reversible representation, we
need to keep the original BPF program around, so that it can be passed back
to user space w/o the need of a complex decoder.
The reason for that use case resides in commit a8fc92778080 ("sk-filter:
Add ability to get socket filter program (v2)"), that is, the ability
to retrieve the currently attached BPF filter from a given socket used
mainly by the checkpoint-restore project, for example.
Therefore, we add two helpers sk_{store,release}_orig_filter for taking
care of that. In the sk_unattached_filter_create() case, there's no such
possibility/requirement to retrieve a loaded BPF program. Therefore, we
can spare us the work in that case.
This approach will simplify and slightly speed up both, sk_get_filter()
and sock_diag_put_filterinfo() handlers as we won't need to successively
decode filters anymore through sk_decode_filter(). As we still need
sk_decode_filter() later on, we're keeping it around.
Joint work with Alexei Starovoitov.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:19 -06:00
|
|
|
struct sock_fprog_kern *fprog;
|
sk-filter: Add ability to get socket filter program (v2)
The SO_ATTACH_FILTER option is set only. I propose to add the get
ability by using SO_ATTACH_FILTER in getsockopt. To be less
irritating to eyes the SO_GET_FILTER alias to it is declared. This
ability is required by checkpoint-restore project to be able to
save full state of a socket.
There are two issues with getting filter back.
First, kernel modifies the sock_filter->code on filter load, thus in
order to return the filter element back to user we have to decode it
into user-visible constants. Fortunately the modification in question
is interconvertible.
Second, the BPF_S_ALU_DIV_K code modifies the command argument k to
speed up the run-time division by doing kernel_k = reciprocal(user_k).
Bad news is that different user_k may result in same kernel_k, so we
can't get the original user_k back. Good news is that we don't have
to do it. What we need to is calculate a user2_k so, that
reciprocal(user2_k) == reciprocal(user_k) == kernel_k
i.e. if it's re-loaded back the compiled again value will be exactly
the same as it was. That said, the user2_k can be calculated like this
user2_k = reciprocal(kernel_k)
with an exception, that if kernel_k == 0, then user2_k == 1.
The optlen argument is treated like this -- when zero, kernel returns
the amount of sock_fprog elements in filter, otherwise it should be
large enough for the sock_fprog array.
changes since v1:
* Declared SO_GET_FILTER in all arch headers
* Added decode of vlan-tag codes
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-10-31 20:01:48 -06:00
|
|
|
struct sk_filter *filter;
|
net: filter: keep original BPF program around
In order to open up the possibility to internally transform a BPF program
into an alternative and possibly non-trivial reversible representation, we
need to keep the original BPF program around, so that it can be passed back
to user space w/o the need of a complex decoder.
The reason for that use case resides in commit a8fc92778080 ("sk-filter:
Add ability to get socket filter program (v2)"), that is, the ability
to retrieve the currently attached BPF filter from a given socket used
mainly by the checkpoint-restore project, for example.
Therefore, we add two helpers sk_{store,release}_orig_filter for taking
care of that. In the sk_unattached_filter_create() case, there's no such
possibility/requirement to retrieve a loaded BPF program. Therefore, we
can spare us the work in that case.
This approach will simplify and slightly speed up both, sk_get_filter()
and sock_diag_put_filterinfo() handlers as we won't need to successively
decode filters anymore through sk_decode_filter(). As we still need
sk_decode_filter() later on, we're keeping it around.
Joint work with Alexei Starovoitov.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:19 -06:00
|
|
|
int ret = 0;
|
sk-filter: Add ability to get socket filter program (v2)
The SO_ATTACH_FILTER option is set only. I propose to add the get
ability by using SO_ATTACH_FILTER in getsockopt. To be less
irritating to eyes the SO_GET_FILTER alias to it is declared. This
ability is required by checkpoint-restore project to be able to
save full state of a socket.
There are two issues with getting filter back.
First, kernel modifies the sock_filter->code on filter load, thus in
order to return the filter element back to user we have to decode it
into user-visible constants. Fortunately the modification in question
is interconvertible.
Second, the BPF_S_ALU_DIV_K code modifies the command argument k to
speed up the run-time division by doing kernel_k = reciprocal(user_k).
Bad news is that different user_k may result in same kernel_k, so we
can't get the original user_k back. Good news is that we don't have
to do it. What we need to is calculate a user2_k so, that
reciprocal(user2_k) == reciprocal(user_k) == kernel_k
i.e. if it's re-loaded back the compiled again value will be exactly
the same as it was. That said, the user2_k can be calculated like this
user2_k = reciprocal(kernel_k)
with an exception, that if kernel_k == 0, then user2_k == 1.
The optlen argument is treated like this -- when zero, kernel returns
the amount of sock_fprog elements in filter, otherwise it should be
large enough for the sock_fprog array.
changes since v1:
* Declared SO_GET_FILTER in all arch headers
* Added decode of vlan-tag codes
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-10-31 20:01:48 -06:00
|
|
|
|
|
|
|
lock_sock(sk);
|
|
|
|
filter = rcu_dereference_protected(sk->sk_filter,
|
2016-04-05 09:10:16 -06:00
|
|
|
lockdep_sock_is_held(sk));
|
sk-filter: Add ability to get socket filter program (v2)
The SO_ATTACH_FILTER option is set only. I propose to add the get
ability by using SO_ATTACH_FILTER in getsockopt. To be less
irritating to eyes the SO_GET_FILTER alias to it is declared. This
ability is required by checkpoint-restore project to be able to
save full state of a socket.
There are two issues with getting filter back.
First, kernel modifies the sock_filter->code on filter load, thus in
order to return the filter element back to user we have to decode it
into user-visible constants. Fortunately the modification in question
is interconvertible.
Second, the BPF_S_ALU_DIV_K code modifies the command argument k to
speed up the run-time division by doing kernel_k = reciprocal(user_k).
Bad news is that different user_k may result in same kernel_k, so we
can't get the original user_k back. Good news is that we don't have
to do it. What we need to is calculate a user2_k so, that
reciprocal(user2_k) == reciprocal(user_k) == kernel_k
i.e. if it's re-loaded back the compiled again value will be exactly
the same as it was. That said, the user2_k can be calculated like this
user2_k = reciprocal(kernel_k)
with an exception, that if kernel_k == 0, then user2_k == 1.
The optlen argument is treated like this -- when zero, kernel returns
the amount of sock_fprog elements in filter, otherwise it should be
large enough for the sock_fprog array.
changes since v1:
* Declared SO_GET_FILTER in all arch headers
* Added decode of vlan-tag codes
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-10-31 20:01:48 -06:00
|
|
|
if (!filter)
|
|
|
|
goto out;
|
net: filter: keep original BPF program around
In order to open up the possibility to internally transform a BPF program
into an alternative and possibly non-trivial reversible representation, we
need to keep the original BPF program around, so that it can be passed back
to user space w/o the need of a complex decoder.
The reason for that use case resides in commit a8fc92778080 ("sk-filter:
Add ability to get socket filter program (v2)"), that is, the ability
to retrieve the currently attached BPF filter from a given socket used
mainly by the checkpoint-restore project, for example.
Therefore, we add two helpers sk_{store,release}_orig_filter for taking
care of that. In the sk_unattached_filter_create() case, there's no such
possibility/requirement to retrieve a loaded BPF program. Therefore, we
can spare us the work in that case.
This approach will simplify and slightly speed up both, sk_get_filter()
and sock_diag_put_filterinfo() handlers as we won't need to successively
decode filters anymore through sk_decode_filter(). As we still need
sk_decode_filter() later on, we're keeping it around.
Joint work with Alexei Starovoitov.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:19 -06:00
|
|
|
|
|
|
|
/* We're copying the filter that has been originally attached,
|
bpf: fix panic in SO_GET_FILTER with native ebpf programs
When sockets have a native eBPF program attached through
setsockopt(sk, SOL_SOCKET, SO_ATTACH_BPF, ...), and then try to
dump these over getsockopt(sk, SOL_SOCKET, SO_GET_FILTER, ...),
the following panic appears:
[49904.178642] BUG: unable to handle kernel NULL pointer dereference at (null)
[49904.178762] IP: [<ffffffff81610fd9>] sk_get_filter+0x39/0x90
[49904.182000] PGD 86fc9067 PUD 531a1067 PMD 0
[49904.185196] Oops: 0000 [#1] SMP
[...]
[49904.224677] Call Trace:
[49904.226090] [<ffffffff815e3d49>] sock_getsockopt+0x319/0x740
[49904.227535] [<ffffffff812f59e3>] ? sock_has_perm+0x63/0x70
[49904.228953] [<ffffffff815e2fc8>] ? release_sock+0x108/0x150
[49904.230380] [<ffffffff812f5a43>] ? selinux_socket_getsockopt+0x23/0x30
[49904.231788] [<ffffffff815dff36>] SyS_getsockopt+0xa6/0xc0
[49904.233267] [<ffffffff8171b9ae>] entry_SYSCALL_64_fastpath+0x12/0x71
The underlying issue is the very same as in commit b382c0865600
("sock, diag: fix panic in sock_diag_put_filterinfo"), that is,
native eBPF programs don't store an original program since this
is only needed in cBPF ones.
However, sk_get_filter() wasn't updated to test for this at the
time when eBPF could be attached. Just throw an error to the user
to indicate that eBPF cannot be dumped over this interface.
That way, it can also be known that a program _is_ attached (as
opposed to just return 0), and a different (future) method needs
to be consulted for a dump.
Fixes: 89aa075832b0 ("net: sock: allow eBPF programs to be attached to sockets")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-10-02 04:06:03 -06:00
|
|
|
* so no conversion/decode needed anymore. eBPF programs that
|
|
|
|
* have no original program cannot be dumped through this.
|
net: filter: keep original BPF program around
In order to open up the possibility to internally transform a BPF program
into an alternative and possibly non-trivial reversible representation, we
need to keep the original BPF program around, so that it can be passed back
to user space w/o the need of a complex decoder.
The reason for that use case resides in commit a8fc92778080 ("sk-filter:
Add ability to get socket filter program (v2)"), that is, the ability
to retrieve the currently attached BPF filter from a given socket used
mainly by the checkpoint-restore project, for example.
Therefore, we add two helpers sk_{store,release}_orig_filter for taking
care of that. In the sk_unattached_filter_create() case, there's no such
possibility/requirement to retrieve a loaded BPF program. Therefore, we
can spare us the work in that case.
This approach will simplify and slightly speed up both, sk_get_filter()
and sock_diag_put_filterinfo() handlers as we won't need to successively
decode filters anymore through sk_decode_filter(). As we still need
sk_decode_filter() later on, we're keeping it around.
Joint work with Alexei Starovoitov.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:19 -06:00
|
|
|
*/
|
bpf: fix panic in SO_GET_FILTER with native ebpf programs
When sockets have a native eBPF program attached through
setsockopt(sk, SOL_SOCKET, SO_ATTACH_BPF, ...), and then try to
dump these over getsockopt(sk, SOL_SOCKET, SO_GET_FILTER, ...),
the following panic appears:
[49904.178642] BUG: unable to handle kernel NULL pointer dereference at (null)
[49904.178762] IP: [<ffffffff81610fd9>] sk_get_filter+0x39/0x90
[49904.182000] PGD 86fc9067 PUD 531a1067 PMD 0
[49904.185196] Oops: 0000 [#1] SMP
[...]
[49904.224677] Call Trace:
[49904.226090] [<ffffffff815e3d49>] sock_getsockopt+0x319/0x740
[49904.227535] [<ffffffff812f59e3>] ? sock_has_perm+0x63/0x70
[49904.228953] [<ffffffff815e2fc8>] ? release_sock+0x108/0x150
[49904.230380] [<ffffffff812f5a43>] ? selinux_socket_getsockopt+0x23/0x30
[49904.231788] [<ffffffff815dff36>] SyS_getsockopt+0xa6/0xc0
[49904.233267] [<ffffffff8171b9ae>] entry_SYSCALL_64_fastpath+0x12/0x71
The underlying issue is the very same as in commit b382c0865600
("sock, diag: fix panic in sock_diag_put_filterinfo"), that is,
native eBPF programs don't store an original program since this
is only needed in cBPF ones.
However, sk_get_filter() wasn't updated to test for this at the
time when eBPF could be attached. Just throw an error to the user
to indicate that eBPF cannot be dumped over this interface.
That way, it can also be known that a program _is_ attached (as
opposed to just return 0), and a different (future) method needs
to be consulted for a dump.
Fixes: 89aa075832b0 ("net: sock: allow eBPF programs to be attached to sockets")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-10-02 04:06:03 -06:00
|
|
|
ret = -EACCES;
|
net: filter: split 'struct sk_filter' into socket and bpf parts
clean up names related to socket filtering and bpf in the following way:
- everything that deals with sockets keeps 'sk_*' prefix
- everything that is pure BPF is changed to 'bpf_*' prefix
split 'struct sk_filter' into
struct sk_filter {
atomic_t refcnt;
struct rcu_head rcu;
struct bpf_prog *prog;
};
and
struct bpf_prog {
u32 jited:1,
len:31;
struct sock_fprog_kern *orig_prog;
unsigned int (*bpf_func)(const struct sk_buff *skb,
const struct bpf_insn *filter);
union {
struct sock_filter insns[0];
struct bpf_insn insnsi[0];
struct work_struct work;
};
};
so that 'struct bpf_prog' can be used independent of sockets and cleans up
'unattached' bpf use cases
split SK_RUN_FILTER macro into:
SK_RUN_FILTER to be used with 'struct sk_filter *' and
BPF_PROG_RUN to be used with 'struct bpf_prog *'
__sk_filter_release(struct sk_filter *) gains
__bpf_prog_release(struct bpf_prog *) helper function
also perform related renames for the functions that work
with 'struct bpf_prog *', since they're on the same lines:
sk_filter_size -> bpf_prog_size
sk_filter_select_runtime -> bpf_prog_select_runtime
sk_filter_free -> bpf_prog_free
sk_unattached_filter_create -> bpf_prog_create
sk_unattached_filter_destroy -> bpf_prog_destroy
sk_store_orig_filter -> bpf_prog_store_orig_filter
sk_release_orig_filter -> bpf_release_orig_filter
__sk_migrate_filter -> bpf_migrate_filter
__sk_prepare_filter -> bpf_prepare_filter
API for attaching classic BPF to a socket stays the same:
sk_attach_filter(prog, struct sock *)/sk_detach_filter(struct sock *)
and SK_RUN_FILTER(struct sk_filter *, ctx) to execute a program
which is used by sockets, tun, af_packet
API for 'unattached' BPF programs becomes:
bpf_prog_create(struct bpf_prog **)/bpf_prog_destroy(struct bpf_prog *)
and BPF_PROG_RUN(struct bpf_prog *, ctx) to execute a program
which is used by isdn, ppp, team, seccomp, ptp, xt_bpf, cls_bpf, test_bpf
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-30 21:34:16 -06:00
|
|
|
fprog = filter->prog->orig_prog;
|
bpf: fix panic in SO_GET_FILTER with native ebpf programs
When sockets have a native eBPF program attached through
setsockopt(sk, SOL_SOCKET, SO_ATTACH_BPF, ...), and then try to
dump these over getsockopt(sk, SOL_SOCKET, SO_GET_FILTER, ...),
the following panic appears:
[49904.178642] BUG: unable to handle kernel NULL pointer dereference at (null)
[49904.178762] IP: [<ffffffff81610fd9>] sk_get_filter+0x39/0x90
[49904.182000] PGD 86fc9067 PUD 531a1067 PMD 0
[49904.185196] Oops: 0000 [#1] SMP
[...]
[49904.224677] Call Trace:
[49904.226090] [<ffffffff815e3d49>] sock_getsockopt+0x319/0x740
[49904.227535] [<ffffffff812f59e3>] ? sock_has_perm+0x63/0x70
[49904.228953] [<ffffffff815e2fc8>] ? release_sock+0x108/0x150
[49904.230380] [<ffffffff812f5a43>] ? selinux_socket_getsockopt+0x23/0x30
[49904.231788] [<ffffffff815dff36>] SyS_getsockopt+0xa6/0xc0
[49904.233267] [<ffffffff8171b9ae>] entry_SYSCALL_64_fastpath+0x12/0x71
The underlying issue is the very same as in commit b382c0865600
("sock, diag: fix panic in sock_diag_put_filterinfo"), that is,
native eBPF programs don't store an original program since this
is only needed in cBPF ones.
However, sk_get_filter() wasn't updated to test for this at the
time when eBPF could be attached. Just throw an error to the user
to indicate that eBPF cannot be dumped over this interface.
That way, it can also be known that a program _is_ attached (as
opposed to just return 0), and a different (future) method needs
to be consulted for a dump.
Fixes: 89aa075832b0 ("net: sock: allow eBPF programs to be attached to sockets")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-10-02 04:06:03 -06:00
|
|
|
if (!fprog)
|
|
|
|
goto out;
|
net: filter: keep original BPF program around
In order to open up the possibility to internally transform a BPF program
into an alternative and possibly non-trivial reversible representation, we
need to keep the original BPF program around, so that it can be passed back
to user space w/o the need of a complex decoder.
The reason for that use case resides in commit a8fc92778080 ("sk-filter:
Add ability to get socket filter program (v2)"), that is, the ability
to retrieve the currently attached BPF filter from a given socket used
mainly by the checkpoint-restore project, for example.
Therefore, we add two helpers sk_{store,release}_orig_filter for taking
care of that. In the sk_unattached_filter_create() case, there's no such
possibility/requirement to retrieve a loaded BPF program. Therefore, we
can spare us the work in that case.
This approach will simplify and slightly speed up both, sk_get_filter()
and sock_diag_put_filterinfo() handlers as we won't need to successively
decode filters anymore through sk_decode_filter(). As we still need
sk_decode_filter() later on, we're keeping it around.
Joint work with Alexei Starovoitov.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:19 -06:00
|
|
|
|
|
|
|
ret = fprog->len;
|
sk-filter: Add ability to get socket filter program (v2)
The SO_ATTACH_FILTER option is set only. I propose to add the get
ability by using SO_ATTACH_FILTER in getsockopt. To be less
irritating to eyes the SO_GET_FILTER alias to it is declared. This
ability is required by checkpoint-restore project to be able to
save full state of a socket.
There are two issues with getting filter back.
First, kernel modifies the sock_filter->code on filter load, thus in
order to return the filter element back to user we have to decode it
into user-visible constants. Fortunately the modification in question
is interconvertible.
Second, the BPF_S_ALU_DIV_K code modifies the command argument k to
speed up the run-time division by doing kernel_k = reciprocal(user_k).
Bad news is that different user_k may result in same kernel_k, so we
can't get the original user_k back. Good news is that we don't have
to do it. What we need to is calculate a user2_k so, that
reciprocal(user2_k) == reciprocal(user_k) == kernel_k
i.e. if it's re-loaded back the compiled again value will be exactly
the same as it was. That said, the user2_k can be calculated like this
user2_k = reciprocal(kernel_k)
with an exception, that if kernel_k == 0, then user2_k == 1.
The optlen argument is treated like this -- when zero, kernel returns
the amount of sock_fprog elements in filter, otherwise it should be
large enough for the sock_fprog array.
changes since v1:
* Declared SO_GET_FILTER in all arch headers
* Added decode of vlan-tag codes
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-10-31 20:01:48 -06:00
|
|
|
if (!len)
|
net: filter: keep original BPF program around
In order to open up the possibility to internally transform a BPF program
into an alternative and possibly non-trivial reversible representation, we
need to keep the original BPF program around, so that it can be passed back
to user space w/o the need of a complex decoder.
The reason for that use case resides in commit a8fc92778080 ("sk-filter:
Add ability to get socket filter program (v2)"), that is, the ability
to retrieve the currently attached BPF filter from a given socket used
mainly by the checkpoint-restore project, for example.
Therefore, we add two helpers sk_{store,release}_orig_filter for taking
care of that. In the sk_unattached_filter_create() case, there's no such
possibility/requirement to retrieve a loaded BPF program. Therefore, we
can spare us the work in that case.
This approach will simplify and slightly speed up both, sk_get_filter()
and sock_diag_put_filterinfo() handlers as we won't need to successively
decode filters anymore through sk_decode_filter(). As we still need
sk_decode_filter() later on, we're keeping it around.
Joint work with Alexei Starovoitov.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:19 -06:00
|
|
|
/* User space only enquires number of filter blocks. */
|
sk-filter: Add ability to get socket filter program (v2)
The SO_ATTACH_FILTER option is set only. I propose to add the get
ability by using SO_ATTACH_FILTER in getsockopt. To be less
irritating to eyes the SO_GET_FILTER alias to it is declared. This
ability is required by checkpoint-restore project to be able to
save full state of a socket.
There are two issues with getting filter back.
First, kernel modifies the sock_filter->code on filter load, thus in
order to return the filter element back to user we have to decode it
into user-visible constants. Fortunately the modification in question
is interconvertible.
Second, the BPF_S_ALU_DIV_K code modifies the command argument k to
speed up the run-time division by doing kernel_k = reciprocal(user_k).
Bad news is that different user_k may result in same kernel_k, so we
can't get the original user_k back. Good news is that we don't have
to do it. What we need to is calculate a user2_k so, that
reciprocal(user2_k) == reciprocal(user_k) == kernel_k
i.e. if it's re-loaded back the compiled again value will be exactly
the same as it was. That said, the user2_k can be calculated like this
user2_k = reciprocal(kernel_k)
with an exception, that if kernel_k == 0, then user2_k == 1.
The optlen argument is treated like this -- when zero, kernel returns
the amount of sock_fprog elements in filter, otherwise it should be
large enough for the sock_fprog array.
changes since v1:
* Declared SO_GET_FILTER in all arch headers
* Added decode of vlan-tag codes
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-10-31 20:01:48 -06:00
|
|
|
goto out;
|
net: filter: keep original BPF program around
In order to open up the possibility to internally transform a BPF program
into an alternative and possibly non-trivial reversible representation, we
need to keep the original BPF program around, so that it can be passed back
to user space w/o the need of a complex decoder.
The reason for that use case resides in commit a8fc92778080 ("sk-filter:
Add ability to get socket filter program (v2)"), that is, the ability
to retrieve the currently attached BPF filter from a given socket used
mainly by the checkpoint-restore project, for example.
Therefore, we add two helpers sk_{store,release}_orig_filter for taking
care of that. In the sk_unattached_filter_create() case, there's no such
possibility/requirement to retrieve a loaded BPF program. Therefore, we
can spare us the work in that case.
This approach will simplify and slightly speed up both, sk_get_filter()
and sock_diag_put_filterinfo() handlers as we won't need to successively
decode filters anymore through sk_decode_filter(). As we still need
sk_decode_filter() later on, we're keeping it around.
Joint work with Alexei Starovoitov.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:19 -06:00
|
|
|
|
sk-filter: Add ability to get socket filter program (v2)
The SO_ATTACH_FILTER option is set only. I propose to add the get
ability by using SO_ATTACH_FILTER in getsockopt. To be less
irritating to eyes the SO_GET_FILTER alias to it is declared. This
ability is required by checkpoint-restore project to be able to
save full state of a socket.
There are two issues with getting filter back.
First, kernel modifies the sock_filter->code on filter load, thus in
order to return the filter element back to user we have to decode it
into user-visible constants. Fortunately the modification in question
is interconvertible.
Second, the BPF_S_ALU_DIV_K code modifies the command argument k to
speed up the run-time division by doing kernel_k = reciprocal(user_k).
Bad news is that different user_k may result in same kernel_k, so we
can't get the original user_k back. Good news is that we don't have
to do it. What we need to is calculate a user2_k so, that
reciprocal(user2_k) == reciprocal(user_k) == kernel_k
i.e. if it's re-loaded back the compiled again value will be exactly
the same as it was. That said, the user2_k can be calculated like this
user2_k = reciprocal(kernel_k)
with an exception, that if kernel_k == 0, then user2_k == 1.
The optlen argument is treated like this -- when zero, kernel returns
the amount of sock_fprog elements in filter, otherwise it should be
large enough for the sock_fprog array.
changes since v1:
* Declared SO_GET_FILTER in all arch headers
* Added decode of vlan-tag codes
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-10-31 20:01:48 -06:00
|
|
|
ret = -EINVAL;
|
net: filter: keep original BPF program around
In order to open up the possibility to internally transform a BPF program
into an alternative and possibly non-trivial reversible representation, we
need to keep the original BPF program around, so that it can be passed back
to user space w/o the need of a complex decoder.
The reason for that use case resides in commit a8fc92778080 ("sk-filter:
Add ability to get socket filter program (v2)"), that is, the ability
to retrieve the currently attached BPF filter from a given socket used
mainly by the checkpoint-restore project, for example.
Therefore, we add two helpers sk_{store,release}_orig_filter for taking
care of that. In the sk_unattached_filter_create() case, there's no such
possibility/requirement to retrieve a loaded BPF program. Therefore, we
can spare us the work in that case.
This approach will simplify and slightly speed up both, sk_get_filter()
and sock_diag_put_filterinfo() handlers as we won't need to successively
decode filters anymore through sk_decode_filter(). As we still need
sk_decode_filter() later on, we're keeping it around.
Joint work with Alexei Starovoitov.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:19 -06:00
|
|
|
if (len < fprog->len)
|
sk-filter: Add ability to get socket filter program (v2)
The SO_ATTACH_FILTER option is set only. I propose to add the get
ability by using SO_ATTACH_FILTER in getsockopt. To be less
irritating to eyes the SO_GET_FILTER alias to it is declared. This
ability is required by checkpoint-restore project to be able to
save full state of a socket.
There are two issues with getting filter back.
First, kernel modifies the sock_filter->code on filter load, thus in
order to return the filter element back to user we have to decode it
into user-visible constants. Fortunately the modification in question
is interconvertible.
Second, the BPF_S_ALU_DIV_K code modifies the command argument k to
speed up the run-time division by doing kernel_k = reciprocal(user_k).
Bad news is that different user_k may result in same kernel_k, so we
can't get the original user_k back. Good news is that we don't have
to do it. What we need to is calculate a user2_k so, that
reciprocal(user2_k) == reciprocal(user_k) == kernel_k
i.e. if it's re-loaded back the compiled again value will be exactly
the same as it was. That said, the user2_k can be calculated like this
user2_k = reciprocal(kernel_k)
with an exception, that if kernel_k == 0, then user2_k == 1.
The optlen argument is treated like this -- when zero, kernel returns
the amount of sock_fprog elements in filter, otherwise it should be
large enough for the sock_fprog array.
changes since v1:
* Declared SO_GET_FILTER in all arch headers
* Added decode of vlan-tag codes
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-10-31 20:01:48 -06:00
|
|
|
goto out;
|
|
|
|
|
|
|
|
ret = -EFAULT;
|
2014-07-30 21:34:13 -06:00
|
|
|
if (copy_to_user(ubuf, fprog->filter, bpf_classic_proglen(fprog)))
|
net: filter: keep original BPF program around
In order to open up the possibility to internally transform a BPF program
into an alternative and possibly non-trivial reversible representation, we
need to keep the original BPF program around, so that it can be passed back
to user space w/o the need of a complex decoder.
The reason for that use case resides in commit a8fc92778080 ("sk-filter:
Add ability to get socket filter program (v2)"), that is, the ability
to retrieve the currently attached BPF filter from a given socket used
mainly by the checkpoint-restore project, for example.
Therefore, we add two helpers sk_{store,release}_orig_filter for taking
care of that. In the sk_unattached_filter_create() case, there's no such
possibility/requirement to retrieve a loaded BPF program. Therefore, we
can spare us the work in that case.
This approach will simplify and slightly speed up both, sk_get_filter()
and sock_diag_put_filterinfo() handlers as we won't need to successively
decode filters anymore through sk_decode_filter(). As we still need
sk_decode_filter() later on, we're keeping it around.
Joint work with Alexei Starovoitov.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:19 -06:00
|
|
|
goto out;
|
sk-filter: Add ability to get socket filter program (v2)
The SO_ATTACH_FILTER option is set only. I propose to add the get
ability by using SO_ATTACH_FILTER in getsockopt. To be less
irritating to eyes the SO_GET_FILTER alias to it is declared. This
ability is required by checkpoint-restore project to be able to
save full state of a socket.
There are two issues with getting filter back.
First, kernel modifies the sock_filter->code on filter load, thus in
order to return the filter element back to user we have to decode it
into user-visible constants. Fortunately the modification in question
is interconvertible.
Second, the BPF_S_ALU_DIV_K code modifies the command argument k to
speed up the run-time division by doing kernel_k = reciprocal(user_k).
Bad news is that different user_k may result in same kernel_k, so we
can't get the original user_k back. Good news is that we don't have
to do it. What we need to is calculate a user2_k so, that
reciprocal(user2_k) == reciprocal(user_k) == kernel_k
i.e. if it's re-loaded back the compiled again value will be exactly
the same as it was. That said, the user2_k can be calculated like this
user2_k = reciprocal(kernel_k)
with an exception, that if kernel_k == 0, then user2_k == 1.
The optlen argument is treated like this -- when zero, kernel returns
the amount of sock_fprog elements in filter, otherwise it should be
large enough for the sock_fprog array.
changes since v1:
* Declared SO_GET_FILTER in all arch headers
* Added decode of vlan-tag codes
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-10-31 20:01:48 -06:00
|
|
|
|
net: filter: keep original BPF program around
In order to open up the possibility to internally transform a BPF program
into an alternative and possibly non-trivial reversible representation, we
need to keep the original BPF program around, so that it can be passed back
to user space w/o the need of a complex decoder.
The reason for that use case resides in commit a8fc92778080 ("sk-filter:
Add ability to get socket filter program (v2)"), that is, the ability
to retrieve the currently attached BPF filter from a given socket used
mainly by the checkpoint-restore project, for example.
Therefore, we add two helpers sk_{store,release}_orig_filter for taking
care of that. In the sk_unattached_filter_create() case, there's no such
possibility/requirement to retrieve a loaded BPF program. Therefore, we
can spare us the work in that case.
This approach will simplify and slightly speed up both, sk_get_filter()
and sock_diag_put_filterinfo() handlers as we won't need to successively
decode filters anymore through sk_decode_filter(). As we still need
sk_decode_filter() later on, we're keeping it around.
Joint work with Alexei Starovoitov.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 11:58:19 -06:00
|
|
|
/* Instead of bytes, the API requests to return the number
|
|
|
|
* of filter blocks.
|
|
|
|
*/
|
|
|
|
ret = fprog->len;
|
sk-filter: Add ability to get socket filter program (v2)
The SO_ATTACH_FILTER option is set only. I propose to add the get
ability by using SO_ATTACH_FILTER in getsockopt. To be less
irritating to eyes the SO_GET_FILTER alias to it is declared. This
ability is required by checkpoint-restore project to be able to
save full state of a socket.
There are two issues with getting filter back.
First, kernel modifies the sock_filter->code on filter load, thus in
order to return the filter element back to user we have to decode it
into user-visible constants. Fortunately the modification in question
is interconvertible.
Second, the BPF_S_ALU_DIV_K code modifies the command argument k to
speed up the run-time division by doing kernel_k = reciprocal(user_k).
Bad news is that different user_k may result in same kernel_k, so we
can't get the original user_k back. Good news is that we don't have
to do it. What we need to is calculate a user2_k so, that
reciprocal(user2_k) == reciprocal(user_k) == kernel_k
i.e. if it's re-loaded back the compiled again value will be exactly
the same as it was. That said, the user2_k can be calculated like this
user2_k = reciprocal(kernel_k)
with an exception, that if kernel_k == 0, then user2_k == 1.
The optlen argument is treated like this -- when zero, kernel returns
the amount of sock_fprog elements in filter, otherwise it should be
large enough for the sock_fprog array.
changes since v1:
* Declared SO_GET_FILTER in all arch headers
* Added decode of vlan-tag codes
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-10-31 20:01:48 -06:00
|
|
|
out:
|
|
|
|
release_sock(sk);
|
|
|
|
return ret;
|
|
|
|
}
|