redonkable
/
remarkable-linux
1
0
Fork 0
Code Releases Activity
remarkable-linux/drivers/pci/setup-res.c

446 lines
12 KiB
C
Raw Normal View History

License cleanup: add SPDX GPL-2.0 license identifier to files with no license Many source files in the tree are missing licensing information, which makes it harder for compliance tools to determine the correct license. By default all files without license information are under the default license of the kernel, which is GPL version 2. Update the files which contain no license information with the 'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally binding shorthand, which can be used instead of the full boiler plate text. This patch is based on work done by Thomas Gleixner and Kate Stewart and Philippe Ombredanne. How this work was done: Patches were generated and checked against linux-4.14-rc6 for a subset of the use cases: - file had no licensing information it it. - file was a */uapi/* one with no licensing information in it, - file was a */uapi/* one with existing licensing information, Further patches will be generated in subsequent months to fix up cases where non-standard license headers were used, and references to license had to be inferred by heuristics based on keywords. The analysis to determine which SPDX License Identifier to be applied to a file was done in a spreadsheet of side by side results from of the output of two independent scanners (ScanCode & Windriver) producing SPDX tag:value files created by Philippe Ombredanne. Philippe prepared the base worksheet, and did an initial spot review of a few 1000 files. The 4.13 kernel was the starting point of the analysis with 60,537 files assessed. Kate Stewart did a file by file comparison of the scanner results in the spreadsheet to determine which SPDX license identifier(s) to be applied to the file. She confirmed any determination that was not immediately clear with lawyers working with the Linux Foundation. Criteria used to select files for SPDX license identifier tagging was: - Files considered eligible had to be source code files. - Make and config files were included as candidates if they contained >5 lines of source - File already had some variant of a license header in it (even if <5 lines). All documentation files were explicitly excluded. The following heuristics were used to determine which SPDX license identifiers to apply. - when both scanners couldn't find any license traces, file was considered to have no license information in it, and the top level COPYING file license applied. For non */uapi/* files that summary was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 11139 and resulted in the first patch in this series. If that file was a */uapi/* path one, it was "GPL-2.0 WITH Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 WITH Linux-syscall-note 930 and resulted in the second patch in this series. - if a file had some form of licensing information in it, and was one of the */uapi/* ones, it was denoted with the Linux-syscall-note if any GPL family license was found in the file or had no licensing in it (per prior point). Results summary: SPDX license identifier # files ---------------------------------------------------|------ GPL-2.0 WITH Linux-syscall-note 270 GPL-2.0+ WITH Linux-syscall-note 169 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17 LGPL-2.1+ WITH Linux-syscall-note 15 GPL-1.0+ WITH Linux-syscall-note 14 ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5 LGPL-2.0+ WITH Linux-syscall-note 4 LGPL-2.1 WITH Linux-syscall-note 3 ((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3 ((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1 and that resulted in the third patch in this series. - when the two scanners agreed on the detected license(s), that became the concluded license(s). - when there was disagreement between the two scanners (one detected a license but the other didn't, or they both detected different licenses) a manual inspection of the file occurred. - In most cases a manual inspection of the information in the file resulted in a clear resolution of the license that should apply (and which scanner probably needed to revisit its heuristics). - When it was not immediately clear, the license identifier was confirmed with lawyers working with the Linux Foundation. - If there was any question as to the appropriate license identifier, the file was flagged for further research and to be revisited later in time. In total, over 70 hours of logged manual review was done on the spreadsheet to determine the SPDX license identifiers to apply to the source files by Kate, Philippe, Thomas and, in some cases, confirmation by lawyers working with the Linux Foundation. Kate also obtained a third independent scan of the 4.13 code base from FOSSology, and compared selected files where the other two scanners disagreed against that SPDX file, to see if there was new insights. The Windriver scanner is based on an older version of FOSSology in part, so they are related. Thomas did random spot checks in about 500 files from the spreadsheets for the uapi headers and agreed with SPDX license identifier in the files he inspected. For the non-uapi files Thomas did random spot checks in about 15000 files. In initial set of patches against 4.14-rc6, 3 files were found to have copy/paste license identifier errors, and have been fixed to reflect the correct identifier. Additionally Philippe spent 10 hours this week doing a detailed manual inspection and review of the 12,461 patched files from the initial patch version early this week with: - a full scancode scan run, collecting the matched texts, detected license ids and scores - reviewing anything where there was a license detected (about 500+ files) to ensure that the applied SPDX license was correct - reviewing anything where there was no detection but the patch license was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied SPDX license was correct This produced a worksheet with 20 files needing minor correction. This worksheet was then exported into 3 different .csv files for the different types of files to be modified. These .csv files were then reviewed by Greg. Thomas wrote a script to parse the csv files and add the proper SPDX tag to the file, in the format that the file expected. This script was further refined by Greg based on the output to detect more types of files automatically and to distinguish between header and source .c files (which need different comment types.) Finally Greg ran the script using the .csv files to generate the patches. Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-01 08:07:57 -06:00
// SPDX-License-Identifier: GPL-2.0
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-16 16:20:36 -06:00
/*
* drivers/pci/setup-res.c
*
* Extruded from code written by
* Dave Rusling (david.rusling@reo.mts.dec.com)
* David Mosberger (davidm@cs.arizona.edu)
* David Miller (davem@redhat.com)
*
* Support routines for initializing a PCI subsystem.
*/
/* fixed for multiple pci buses, 1999 Andrea Arcangeli <andrea@suse.de> */
/*
* Nov 2000, Ivan Kokshaysky <ink@jurassic.park.msu.ru>
* Resource sorting
*/
#include <linux/kernel.h>
pci: Fix files needing export.h for EXPORT_SYMBOL/THIS_MODULE They were implicitly getting it from device.h --> module.h but we want to clean that up. So add the minimal header for these macros. Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2011-05-27 07:37:25 -06:00
#include <linux/export.h>
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-16 16:20:36 -06:00
#include <linux/pci.h>
#include <linux/errno.h>
#include <linux/ioport.h>
#include <linux/cache.h>
#include <linux/slab.h>
#include "pci.h"
PCI: Separate VF BAR updates from standard BAR updates Previously pci_update_resource() used the same code path for updating standard BARs and VF BARs in SR-IOV capabilities. Split the VF BAR update into a new pci_iov_update_resource() internal interface, which makes it simpler to compute the BAR address (we can get rid of pci_resource_bar() and pci_iov_resource_bar()). This patch: - Renames pci_update_resource() to pci_std_update_resource(), - Adds pci_iov_update_resource(), - Makes pci_update_resource() a wrapper that calls the appropriate one, No functional change intended. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
2016-11-28 08:15:52 -07:00
static void pci_std_update_resource(struct pci_dev *dev, int resno)
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-16 16:20:36 -06:00
{
struct pci_bus_region region;
PCI: disable MEM decoding while updating 64-bit MEM BARs When we update 64-bit BARs, we have to perform two config writes. Between the writes, the half-written BAR value could match a MEM access intended for another device. This could result in corruption of this device (for writes) or an unexpected response machine check (for reads). To prevent this, disable MEM decoding while updating such BARs. This uses the same safety test as 253d2e5498, which disables both MEM and IO while sizing BARs, namely, we don't disable decoding for host bridge devices. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2012-07-09 19:49:37 -06:00
bool disable;
u16 cmd;
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-16 16:20:36 -06:00
u32 new, check, mask;
int reg;
PCI: remove unnecessary arg of pci_update_resource() This cleanup removes unnecessary argument 'struct resource *res' in pci_update_resource(), so it takes same arguments as other companion functions (pci_assign_resource(), etc.). Signed-off-by: Yu Zhao <yu.zhao@intel.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2008-11-21 11:38:52 -07:00
struct resource *res = dev->resource + resno;
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-16 16:20:36 -06:00
PCI: Ignore BAR updates on virtual functions VF BARs are read-only zero, so updating VF BARs will not have any effect. See the SR-IOV spec r1.1, sec 3.4.1.11. We already ignore these updates because of 70675e0b6a1a ("PCI: Don't try to restore VF BARs"); this merely restructures it slightly to make it easier to split updates for standard and SR-IOV BARs. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
2016-11-28 10:19:27 -07:00
/* Per SR-IOV spec 3.4.1.11, VF BARs are RO zero */
if (dev->is_virtfn)
PCI: Don't try to restore VF BARs VF BARs are read-only zero, so updating VF BARs will not have any effect. See the SR-IOV spec r1.1, sec 3.4.1.11. Don't update VF BARs in pci_restore_bars(). This avoids spurious "BAR %d: error updating" messages that we see when doing vfio pass-through after 6eb7018705de ("vfio-pci: Move idle devices to D3hot power state"). [bhelgaas: changelog, fix whitespace] Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2015-07-29 02:52:58 -06:00
return;
PCI legacy resource fix Since commit 368c73d4f689dae0807d0a2aa74c61fd2b9b075f the kernel will try to update the non-writeable BAR registers 0..3 of PIIX4 IDE adapters if pci_assign_unassigned_resources() is used to do full resource assignment of the bus. This fails because in the PIIX4 these BAR registers have implicitly assumed values and read back as zero; it used to work because the kernel used to just write zero to that register the read back value did match what was written. The fix is a new resource flag IORESOURCE_PCI_FIXED used to mark a resource as non-movable. This will also be useful to keep other import system resources from being moved around - for example system consoles on PCI busses. [akpm@osdl.org: cleanup] Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Acked-by: Alan Cox <alan@redhat.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-19 14:12:08 -07:00
/*
* Ignore resources for unimplemented BARs and unused resource slots
* for 64 bit BARs.
*/
[PATCH] Fix restore of 64-bit PCI BAR's For 64-bit BAR[i] only pci_dev->resource[i] is valid, ->resource[i+1] slot is unused and contains zeroes in all fields. So when we update a PCI BAR, all we need is just to check that we're going to update a _valid_ resource. Also make sure to write high bits - use "x >> 16 >> 16" (rather than the simpler ">> 32") to avoid warnings on 32-bit architectures where we're not going to have any high bits. Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-08-07 03:49:59 -06:00
if (!res->flags)
return;
PCI: Check IORESOURCE_UNSET before updating BAR Check to make sure we don't update a BAR with an address we haven't assigned. If we haven't assigned an address to a resource, we shouldn't write it to a BAR. This isn't a problem for the usual path via pci_assign_resource(), which clears IORESOURCE_UNSET before calling pci_update_resource(), but paths like pci_restore_bars() can call this for resources we haven't assigned. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2014-02-26 11:25:59 -07:00
if (res->flags & IORESOURCE_UNSET)
return;
PCI legacy resource fix Since commit 368c73d4f689dae0807d0a2aa74c61fd2b9b075f the kernel will try to update the non-writeable BAR registers 0..3 of PIIX4 IDE adapters if pci_assign_unassigned_resources() is used to do full resource assignment of the bus. This fails because in the PIIX4 these BAR registers have implicitly assumed values and read back as zero; it used to work because the kernel used to just write zero to that register the read back value did match what was written. The fix is a new resource flag IORESOURCE_PCI_FIXED used to mark a resource as non-movable. This will also be useful to keep other import system resources from being moved around - for example system consoles on PCI busses. [akpm@osdl.org: cleanup] Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Acked-by: Alan Cox <alan@redhat.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-19 14:12:08 -07:00
/*
* Ignore non-moveable resources. This might be legacy resources for
* which no functional BAR register exists or another important
PCI: use dev_printk when possible Convert printks to use dev_printk(). I converted pr_debug() to dev_dbg(). Both use KERN_DEBUG and are enabled only when DEBUG is defined. I converted printk(KERN_DEBUG) to dev_printk(KERN_DEBUG), not to dev_dbg(), because dev_dbg() is only enabled when DEBUG is defined. I converted DBG(KERN_INFO) (only in setup-bus.c) to dev_info(). The DBG() name makes it sound like debug, but it's been enabled forever, so dev_info() preserves the previous behavior. I tried to make the resource assignment formats more consistent, e.g., "BAR %d: got res [%#llx-%#llx] bus [%#llx-%#llx] flags %#lx\n" instead of sometimes using "start-end" and sometimes using "size@start". I'm not attached to one or the other; I'd just like them consistent. Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2008-06-13 10:52:11 -06:00
* system resource we shouldn't move around.
PCI legacy resource fix Since commit 368c73d4f689dae0807d0a2aa74c61fd2b9b075f the kernel will try to update the non-writeable BAR registers 0..3 of PIIX4 IDE adapters if pci_assign_unassigned_resources() is used to do full resource assignment of the bus. This fails because in the PIIX4 these BAR registers have implicitly assumed values and read back as zero; it used to work because the kernel used to just write zero to that register the read back value did match what was written. The fix is a new resource flag IORESOURCE_PCI_FIXED used to mark a resource as non-movable. This will also be useful to keep other import system resources from being moved around - for example system consoles on PCI busses. [akpm@osdl.org: cleanup] Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Acked-by: Alan Cox <alan@redhat.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-19 14:12:08 -07:00
*/
if (res->flags & IORESOURCE_PCI_FIXED)
return;
PCI: Convert pcibios_resource_to_bus() to take a pci_bus, not a pci_dev These interfaces: pcibios_resource_to_bus(struct pci_dev *dev, *bus_region, *resource) pcibios_bus_to_resource(struct pci_dev *dev, *resource, *bus_region) took a pci_dev, but they really depend only on the pci_bus. And we want to use them in resource allocation paths where we have the bus but not a device, so this patch converts them to take the pci_bus instead of the pci_dev: pcibios_resource_to_bus(struct pci_bus *bus, *bus_region, *resource) pcibios_bus_to_resource(struct pci_bus *bus, *resource, *bus_region) In fact, with standard PCI-PCI bridges, they only depend on the host bridge, because that's the only place address translation occurs, but we aren't going that far yet. [bhelgaas: changelog] Signed-off-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2013-12-09 23:54:40 -07:00
pcibios_resource_to_bus(dev->bus, &region, res);
PCI: Update BARs using property bits appropriate for type The BAR property bits (0-3 for memory BARs, 0-1 for I/O BARs) are supposed to be read-only, but we do save them in res->flags and include them when updating the BAR. Mask the I/O property bits with ~PCI_BASE_ADDRESS_IO_MASK (0x3) instead of PCI_REGION_FLAG_MASK (0xf) to make it obvious that we can't corrupt bits 2-3 of I/O addresses. Use PCI_ROM_ADDRESS_MASK for ROM BARs. This means we'll only check the top 21 bits (instead of the 28 bits we used to check) of a ROM BAR to see if the update was successful. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2016-11-29 07:14:47 -07:00
new = region.start;
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-16 16:20:36 -06:00
PCI: Update BARs using property bits appropriate for type The BAR property bits (0-3 for memory BARs, 0-1 for I/O BARs) are supposed to be read-only, but we do save them in res->flags and include them when updating the BAR. Mask the I/O property bits with ~PCI_BASE_ADDRESS_IO_MASK (0x3) instead of PCI_REGION_FLAG_MASK (0xf) to make it obvious that we can't corrupt bits 2-3 of I/O addresses. Use PCI_ROM_ADDRESS_MASK for ROM BARs. This means we'll only check the top 21 bits (instead of the 28 bits we used to check) of a ROM BAR to see if the update was successful. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2016-11-29 07:14:47 -07:00
if (res->flags & IORESOURCE_IO) {
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-16 16:20:36 -06:00
mask = (u32)PCI_BASE_ADDRESS_IO_MASK;
PCI: Update BARs using property bits appropriate for type The BAR property bits (0-3 for memory BARs, 0-1 for I/O BARs) are supposed to be read-only, but we do save them in res->flags and include them when updating the BAR. Mask the I/O property bits with ~PCI_BASE_ADDRESS_IO_MASK (0x3) instead of PCI_REGION_FLAG_MASK (0xf) to make it obvious that we can't corrupt bits 2-3 of I/O addresses. Use PCI_ROM_ADDRESS_MASK for ROM BARs. This means we'll only check the top 21 bits (instead of the 28 bits we used to check) of a ROM BAR to see if the update was successful. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2016-11-29 07:14:47 -07:00
new |= res->flags & ~PCI_BASE_ADDRESS_IO_MASK;
} else if (resno == PCI_ROM_RESOURCE) {
PCI: Make PCI_ROM_ADDRESS_MASK a 32-bit constant A 64-bit value is not needed since a PCI ROM address consists in 32 bits. This fixes a clang warning about "implicit conversion from 'unsigned long' to 'u32'". Also remove now unnecessary casts to u32 from __pci_read_base() and pci_std_update_resource(). Signed-off-by: Matthias Kaehlcke <mka@chromium.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2017-04-14 14:38:02 -06:00
mask = PCI_ROM_ADDRESS_MASK;
PCI: Update BARs using property bits appropriate for type The BAR property bits (0-3 for memory BARs, 0-1 for I/O BARs) are supposed to be read-only, but we do save them in res->flags and include them when updating the BAR. Mask the I/O property bits with ~PCI_BASE_ADDRESS_IO_MASK (0x3) instead of PCI_REGION_FLAG_MASK (0xf) to make it obvious that we can't corrupt bits 2-3 of I/O addresses. Use PCI_ROM_ADDRESS_MASK for ROM BARs. This means we'll only check the top 21 bits (instead of the 28 bits we used to check) of a ROM BAR to see if the update was successful. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2016-11-29 07:14:47 -07:00
} else {
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-16 16:20:36 -06:00
mask = (u32)PCI_BASE_ADDRESS_MEM_MASK;
PCI: Update BARs using property bits appropriate for type The BAR property bits (0-3 for memory BARs, 0-1 for I/O BARs) are supposed to be read-only, but we do save them in res->flags and include them when updating the BAR. Mask the I/O property bits with ~PCI_BASE_ADDRESS_IO_MASK (0x3) instead of PCI_REGION_FLAG_MASK (0xf) to make it obvious that we can't corrupt bits 2-3 of I/O addresses. Use PCI_ROM_ADDRESS_MASK for ROM BARs. This means we'll only check the top 21 bits (instead of the 28 bits we used to check) of a ROM BAR to see if the update was successful. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2016-11-29 07:14:47 -07:00
new |= res->flags & ~PCI_BASE_ADDRESS_MEM_MASK;
}
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-16 16:20:36 -06:00
PCI: Remove pci_resource_bar() and pci_iov_resource_bar() pci_std_update_resource() only deals with standard BARs, so we don't have to worry about the complications of VF BARs in an SR-IOV capability. Compute the BAR address inline and remove pci_resource_bar(). That makes pci_iov_resource_bar() unused, so remove that as well. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
2016-11-28 15:51:19 -07:00
if (resno < PCI_ROM_RESOURCE) {
reg = PCI_BASE_ADDRESS_0 + 4 * resno;
} else if (resno == PCI_ROM_RESOURCE) {
PCI: Add comments about ROM BAR updating pci_update_resource() updates a hardware BAR so its address matches the kernel's struct resource UNLESS it's a disabled ROM BAR. We only update those when we enable the ROM. It's not obvious from the code why ROM BARs should be handled specially. Apparently there are Matrox devices with defective ROM BARs that read as zero when disabled. That means that if pci_enable_rom() reads the disabled BAR, sets PCI_ROM_ADDRESS_ENABLE (without re-inserting the address), and writes it back, it would enable the ROM at address zero. Add comments and references to explain why we can't make the code look more rational. The code changes are from 755528c860b0 ("Ignore disabled ROM resources at setup") and 8085ce084c0f ("[PATCH] Fix PCI ROM mapping"). Link: https://lkml.org/lkml/2005/8/30/138 Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
2016-11-28 15:17:41 -07:00
/*
* Apparently some Matrox devices have ROM BARs that read
* as zero when disabled, so don't update ROM BARs unless
* they're enabled. See https://lkml.org/lkml/2005/8/30/138.
*/
Ignore disabled ROM resources at setup Writing even a disabled value seems to mess up some matrox graphics cards. It may be a card-related issue, but we may also be writing reserved low bits in the result. This was a fall-out of switching x86 over to the generic PCI resource allocation code, and needs more debugging. In particular, the old x86 code defaulted to not doing any resource allocations at all for ROM resources. In the meantime, this has been reported to make X happier by Helge Hafting <helgehaf@aitel.hist.no>. Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-08-26 11:49:22 -06:00
if (!(res->flags & IORESOURCE_ROM_ENABLE))
return;
PCI: Remove pci_resource_bar() and pci_iov_resource_bar() pci_std_update_resource() only deals with standard BARs, so we don't have to worry about the complications of VF BARs in an SR-IOV capability. Compute the BAR address inline and remove pci_resource_bar(). That makes pci_iov_resource_bar() unused, so remove that as well. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
2016-11-28 15:51:19 -07:00
reg = dev->rom_base_reg;
Ignore disabled ROM resources at setup Writing even a disabled value seems to mess up some matrox graphics cards. It may be a card-related issue, but we may also be writing reserved low bits in the result. This was a fall-out of switching x86 over to the generic PCI resource allocation code, and needs more debugging. In particular, the old x86 code defaulted to not doing any resource allocations at all for ROM resources. In the meantime, this has been reported to make X happier by Helge Hafting <helgehaf@aitel.hist.no>. Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-08-26 11:49:22 -06:00
new |= PCI_ROM_ADDRESS_ENABLE;
PCI: Remove pci_resource_bar() and pci_iov_resource_bar() pci_std_update_resource() only deals with standard BARs, so we don't have to worry about the complications of VF BARs in an SR-IOV capability. Compute the BAR address inline and remove pci_resource_bar(). That makes pci_iov_resource_bar() unused, so remove that as well. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
2016-11-28 15:51:19 -07:00
} else
return;
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-16 16:20:36 -06:00
PCI: disable MEM decoding while updating 64-bit MEM BARs When we update 64-bit BARs, we have to perform two config writes. Between the writes, the half-written BAR value could match a MEM access intended for another device. This could result in corruption of this device (for writes) or an unexpected response machine check (for reads). To prevent this, disable MEM decoding while updating such BARs. This uses the same safety test as 253d2e5498, which disables both MEM and IO while sizing BARs, namely, we don't disable decoding for host bridge devices. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2012-07-09 19:49:37 -06:00
/*
* We can't update a 64-bit BAR atomically, so when possible,
* disable decoding so that a half-updated BAR won't conflict
* with another device.
*/
disable = (res->flags & IORESOURCE_MEM_64) && !dev->mmio_always_on;
if (disable) {
pci_read_config_word(dev, PCI_COMMAND, &cmd);
pci_write_config_word(dev, PCI_COMMAND,
cmd & ~PCI_COMMAND_MEMORY);
}
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-16 16:20:36 -06:00
pci_write_config_dword(dev, reg, new);
pci_read_config_dword(dev, reg, &check);
if ((new ^ check) & mask) {
PCI: use dev_printk when possible Convert printks to use dev_printk(). I converted pr_debug() to dev_dbg(). Both use KERN_DEBUG and are enabled only when DEBUG is defined. I converted printk(KERN_DEBUG) to dev_printk(KERN_DEBUG), not to dev_dbg(), because dev_dbg() is only enabled when DEBUG is defined. I converted DBG(KERN_INFO) (only in setup-bus.c) to dev_info(). The DBG() name makes it sound like debug, but it's been enabled forever, so dev_info() preserves the previous behavior. I tried to make the resource assignment formats more consistent, e.g., "BAR %d: got res [%#llx-%#llx] bus [%#llx-%#llx] flags %#lx\n" instead of sometimes using "start-end" and sometimes using "size@start". I'm not attached to one or the other; I'd just like them consistent. Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2008-06-13 10:52:11 -06:00
dev_err(&dev->dev, "BAR %d: error updating (%#08x != %#08x)\n",
resno, new, check);
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-16 16:20:36 -06:00
}
PCI: fold pci_calc_resource_flags() into decode_bar() decode_bar() and pci_calc_resource_flags() both looked at the PCI BAR type information, and it's simpler to just do it all in one place. decode_bar() sets IORESOURCE_IO, IORESOURCE_MEM, and IORESOURCE_MEM_64 as appropriate, so res->flags contains all the information pci_bar_type does, so we don't need to test the pci_bar_type return value. decode_bar() used to return pci_bar_type, which we no longer need. We can simplify it a bit by returning the struct resource flags rather than updating them internally. In pci_update_resource(), there's no need to decode the BAR type bits again; we can just test for IORESOURCE_MEM_64 directly. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-06-14 13:04:35 -06:00
if (res->flags & IORESOURCE_MEM_64) {
[PATCH] Fix restore of 64-bit PCI BAR's For 64-bit BAR[i] only pci_dev->resource[i] is valid, ->resource[i+1] slot is unused and contains zeroes in all fields. So when we update a PCI BAR, all we need is just to check that we're going to update a _valid_ resource. Also make sure to write high bits - use "x >> 16 >> 16" (rather than the simpler ">> 32") to avoid warnings on 32-bit architectures where we're not going to have any high bits. Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-08-07 03:49:59 -06:00
new = region.start >> 16 >> 16;
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-16 16:20:36 -06:00
pci_write_config_dword(dev, reg + 4, new);
pci_read_config_dword(dev, reg + 4, &check);
if (check != new) {
PCI: Merge multi-line quoted strings Merge quoted strings that are broken across lines into a single entity. The compiler merges them anyway, but checkpatch complains about it, and merging them makes it easier to grep for strings. No functional change. [bhelgaas: changelog, do the same for everything under drivers/pci] Signed-off-by: Ryan Desfosses <ryan@desfo.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2014-04-18 18:13:50 -06:00
dev_err(&dev->dev, "BAR %d: error updating (high %#08x != %#08x)\n",
resno, new, check);
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-16 16:20:36 -06:00
}
}
PCI: disable MEM decoding while updating 64-bit MEM BARs When we update 64-bit BARs, we have to perform two config writes. Between the writes, the half-written BAR value could match a MEM access intended for another device. This could result in corruption of this device (for writes) or an unexpected response machine check (for reads). To prevent this, disable MEM decoding while updating such BARs. This uses the same safety test as 253d2e5498, which disables both MEM and IO while sizing BARs, namely, we don't disable decoding for host bridge devices. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2012-07-09 19:49:37 -06:00
if (disable)
pci_write_config_word(dev, PCI_COMMAND, cmd);
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-16 16:20:36 -06:00
}
PCI: Separate VF BAR updates from standard BAR updates Previously pci_update_resource() used the same code path for updating standard BARs and VF BARs in SR-IOV capabilities. Split the VF BAR update into a new pci_iov_update_resource() internal interface, which makes it simpler to compute the BAR address (we can get rid of pci_resource_bar() and pci_iov_resource_bar()). This patch: - Renames pci_update_resource() to pci_std_update_resource(), - Adds pci_iov_update_resource(), - Makes pci_update_resource() a wrapper that calls the appropriate one, No functional change intended. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
2016-11-28 08:15:52 -07:00
void pci_update_resource(struct pci_dev *dev, int resno)
{
if (resno <= PCI_ROM_RESOURCE)
pci_std_update_resource(dev, resno);
#ifdef CONFIG_PCI_IOV
else if (resno >= PCI_IOV_RESOURCES && resno <= PCI_IOV_RESOURCE_END)
pci_iov_update_resource(dev, resno);
#endif
}
pci: do not mark exported functions as __devinit Functions marked __devinit will be removed after kernel init. But being exported they are potentially called by a module much later. So the safer choice seems to be to keep the function even in the non CONFIG_HOTPLUG case. This silence the follwoing section mismatch warnings: WARNING: drivers/built-in.o - Section mismatch: reference to .init.text:pci_bus_add_device from __ksymtab_gpl between '__ksymtab_pci_bus_add_device' (at offset 0x20) and '__ksymtab_pci_walk_bus' WARNING: drivers/built-in.o - Section mismatch: reference to .init.text:pci_create_bus from __ksymtab_gpl between '__ksymtab_pci_create_bus' (at offset 0x40) and '__ksymtab_pci_stop_bus_device' WARNING: drivers/built-in.o - Section mismatch: reference to .init.text:pci_bus_max_busnr from __ksymtab_gpl between '__ksymtab_pci_bus_max_busnr' (at offset 0xc0) and '__ksymtab_pci_assign_resource_fixed' WARNING: drivers/built-in.o - Section mismatch: reference to .init.text:pci_claim_resource from __ksymtab_gpl between '__ksymtab_pci_claim_resource' (at offset 0xe0) and '__ksymtab_pcie_port_bus_type' WARNING: drivers/built-in.o - Section mismatch: reference to .init.text:pci_bus_add_devices from __ksymtab between '__ksymtab_pci_bus_add_devices' (at offset 0x70) and '__ksymtab_pci_bus_alloc_resource' WARNING: drivers/built-in.o - Section mismatch: reference to .init.text:pci_scan_bus_parented from __ksymtab between '__ksymtab_pci_scan_bus_parented' (at offset 0x90) and '__ksymtab_pci_root_buses' WARNING: drivers/built-in.o - Section mismatch: reference to .init.text:pci_bus_assign_resources from __ksymtab between '__ksymtab_pci_bus_assign_resources' (at offset 0x4d0) and '__ksymtab_pci_bus_size_bridges' WARNING: drivers/built-in.o - Section mismatch: reference to .init.text:pci_bus_size_bridges from __ksymtab between '__ksymtab_pci_bus_size_bridges' (at offset 0x4e0) and '__ksymtab_pci_setup_cardbus' Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-03-26 23:53:30 -06:00
int pci_claim_resource(struct pci_dev *dev, int resource)
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-16 16:20:36 -06:00
{
struct resource *res = &dev->resource[resource];
PCI: for address space collisions, show conflicting resource With request_resource_conflict(), we can learn what the actual conflict is, so print that info for debugging purposes. Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-03-11 17:01:19 -07:00
struct resource *root, *conflict;
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-16 16:20:36 -06:00
PCI: Don't try to claim IORESOURCE_UNSET resources If the IORESOURCE_UNSET bit is set, it means we haven't assigned an address yet, so don't try to claim the region. Also, make the error messages more uniform and add info about which BAR is involved. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2014-02-26 11:25:59 -07:00
if (res->flags & IORESOURCE_UNSET) {
dev_info(&dev->dev, "can't claim BAR %d %pR: no address assigned\n",
resource, res);
return -EINVAL;
}
PCI: Don't attempt to claim shadow copies of ROM If we're using a shadow copy of a PCI device ROM, the shadow copy is in RAM and the device never sees accesses to it and doesn't respond to it. We don't have to route the shadow range to the PCI device, and the device doesn't have to claim the range. Previously we treated the shadow copy as though it were the ROM BAR, and we failed to claim it because the region wasn't routed to the device: pci 0000:01:00.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff] pci_bus 0000:01: Allocating resources pci 0000:01:00.0: can't claim BAR 6 [mem 0x000c0000-0x000dffff]: no compatible bridge window The failure path of pcibios_allocate_dev_rom_resource() cleared out the resource start address, which also caused the following ioremap() warning: WARNING: CPU: 0 PID: 116 at /build/linux-akdJXO/linux-4.8.0/arch/x86/mm/ioremap.c:121 __ioremap_caller+0x1ec/0x370 ioremap on RAM at 0x0000000000000000 - 0x000000000001ffff Handle an option ROM shadow copy as RAM, without trying to insert it into the iomem resource tree. This fixes a regression caused by 0c0e0736acad ("PCI: Set ROM shadow location in arch code, not in PCI core"), which appeared in v4.6. The regression causes video device initialization to fail. This was reported on AMD Turks, but it likely affects others as well. Fixes: 0c0e0736acad ("PCI: Set ROM shadow location in arch code, not in PCI core") Reported-and-tested-by: Vecu Bosseur <vecu.bosseur@gmail.com> Link: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1627496 Link: https://bugzilla.kernel.org/show_bug.cgi?id=175391 Link: https://bugzilla.redhat.com/show_bug.cgi?id=1352272 Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> CC: stable@vger.kernel.org # v4.6+
2016-11-08 13:25:24 -07:00
/*
* If we have a shadow copy in RAM, the PCI device doesn't respond
* to the shadow range, so we don't need to claim it, and upstream
* bridges don't need to route the range to the device.
*/
if (res->flags & IORESOURCE_ROM_SHADOW)
return 0;
Fix pci_claim_resource Instead of starting from the iomem or ioport roots, start from the parent bus' resources. This fixes a bug where child resources would appear above their parents resources if they had the same size. Signed-off-by: Matthew Wilcox <willy@linux.intel.com> Tested-by: Andrew Patterson <andrew.patterson@hp.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-17 14:33:33 -06:00
root = pci_find_parent_resource(dev, res);
PCI: improve discovery/configuration messages This makes PCI resource management messages more consistent and adds a few new messages to aid debugging. Whenever we assign resources to a device, update a BAR, or change a bridge aperture, it's worth noting it. Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-11-04 10:32:57 -07:00
if (!root) {
PCI: Don't try to claim IORESOURCE_UNSET resources If the IORESOURCE_UNSET bit is set, it means we haven't assigned an address yet, so don't try to claim the region. Also, make the error messages more uniform and add info about which BAR is involved. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2014-02-26 11:25:59 -07:00
dev_info(&dev->dev, "can't claim BAR %d %pR: no compatible bridge window\n",
resource, res);
PCI: Mark invalid BARs as unassigned If a BAR is not inside any upstream bridge window, or if it conflicts with another resource, mark it as IORESOURCE_UNSET so we don't try to use it. We may be able to assign a different address for it. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-03-12 11:30:06 -06:00
res->flags |= IORESOURCE_UNSET;
PCI: improve discovery/configuration messages This makes PCI resource management messages more consistent and adds a few new messages to aid debugging. Whenever we assign resources to a device, update a BAR, or change a bridge aperture, it's worth noting it. Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-11-04 10:32:57 -07:00
return -EINVAL;
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-16 16:20:36 -06:00
}
PCI: for address space collisions, show conflicting resource With request_resource_conflict(), we can learn what the actual conflict is, so print that info for debugging purposes. Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-03-11 17:01:19 -07:00
conflict = request_resource_conflict(root, res);
if (conflict) {
PCI: Don't try to claim IORESOURCE_UNSET resources If the IORESOURCE_UNSET bit is set, it means we haven't assigned an address yet, so don't try to claim the region. Also, make the error messages more uniform and add info about which BAR is involved. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2014-02-26 11:25:59 -07:00
dev_info(&dev->dev, "can't claim BAR %d %pR: address conflict with %s %pR\n",
resource, res, conflict->name, conflict);
PCI: Mark invalid BARs as unassigned If a BAR is not inside any upstream bridge window, or if it conflicts with another resource, mark it as IORESOURCE_UNSET so we don't try to use it. We may be able to assign a different address for it. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-03-12 11:30:06 -06:00
res->flags |= IORESOURCE_UNSET;
PCI: for address space collisions, show conflicting resource With request_resource_conflict(), we can learn what the actual conflict is, so print that info for debugging purposes. Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-03-11 17:01:19 -07:00
return -EBUSY;
}
PCI: improve discovery/configuration messages This makes PCI resource management messages more consistent and adds a few new messages to aid debugging. Whenever we assign resources to a device, update a BAR, or change a bridge aperture, it's worth noting it. Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-11-04 10:32:57 -07:00
PCI: for address space collisions, show conflicting resource With request_resource_conflict(), we can learn what the actual conflict is, so print that info for debugging purposes. Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-03-11 17:01:19 -07:00
return 0;
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-16 16:20:36 -06:00
}
PCI: export pci_claim_resource for driver use yenta needs this for example. Acked-by: Matthew Wilcox <willy@linux.intel.com> Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-06-30 22:45:44 -06:00
EXPORT_SYMBOL(pci_claim_resource);
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-16 16:20:36 -06:00
PCI: allow assignment of memory resources with a specified alignment This patch allows memory resources to be assigned with a specified alignment at boot-time or run-time. The patch is useful when we use PCI pass-through, because page-aligned memory resources are required to securely share PCI resources with guest drivers. If you want to assign the resource at boot time, please set "pci=resource_alignment=" boot parameter. This is format of "pci=resource_alignment=" boot parameter: [<order of align>@][<domain>:]<bus>:<slot>.<func>[; ...] Specifies alignment and device to reassign aligned memory resources. If <order of align> is not specified, PAGE_SIZE is used as alignment. PCI-PCI bridge can be specified, if resource windows need to be expanded. This is example: pci=resource_alignment=20@07:00.0;18@0f:00.0;00:1d.7 If you want to assign the resource at run-time, please set "/sys/bus/pci/resource_alignment" file, and hot-remove the device and hot-add the device. For this purpose, fakephp or PCI hotplug interfaces can be used. The format of "/sys/bus/pci/resource_alignment" file is the same with boot parameter. You can use "," instead of ";". For example: # cd /sys/bus/pci # echo -n 20@12:00.0 > resource_alignment # echo 1 > devices/0000:12:00.0/remove # echo 1 > rescan Reviewed-by: Alex Chiang <achiang@hp.com> Reviewed-by: Yu Zhao <yu.zhao@intel.com> Signed-off-by: Yuji Shimada <shimada-yxb@necst.nec.co.jp> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-03-16 02:13:39 -06:00
void pci_disable_bridge_window(struct pci_dev *dev)
{
PCI: improve discovery/configuration messages This makes PCI resource management messages more consistent and adds a few new messages to aid debugging. Whenever we assign resources to a device, update a BAR, or change a bridge aperture, it's worth noting it. Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-11-04 10:32:57 -07:00
dev_info(&dev->dev, "disabling bridge mem windows\n");
PCI: allow assignment of memory resources with a specified alignment This patch allows memory resources to be assigned with a specified alignment at boot-time or run-time. The patch is useful when we use PCI pass-through, because page-aligned memory resources are required to securely share PCI resources with guest drivers. If you want to assign the resource at boot time, please set "pci=resource_alignment=" boot parameter. This is format of "pci=resource_alignment=" boot parameter: [<order of align>@][<domain>:]<bus>:<slot>.<func>[; ...] Specifies alignment and device to reassign aligned memory resources. If <order of align> is not specified, PAGE_SIZE is used as alignment. PCI-PCI bridge can be specified, if resource windows need to be expanded. This is example: pci=resource_alignment=20@07:00.0;18@0f:00.0;00:1d.7 If you want to assign the resource at run-time, please set "/sys/bus/pci/resource_alignment" file, and hot-remove the device and hot-add the device. For this purpose, fakephp or PCI hotplug interfaces can be used. The format of "/sys/bus/pci/resource_alignment" file is the same with boot parameter. You can use "," instead of ";". For example: # cd /sys/bus/pci # echo -n 20@12:00.0 > resource_alignment # echo 1 > devices/0000:12:00.0/remove # echo 1 > rescan Reviewed-by: Alex Chiang <achiang@hp.com> Reviewed-by: Yu Zhao <yu.zhao@intel.com> Signed-off-by: Yuji Shimada <shimada-yxb@necst.nec.co.jp> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-03-16 02:13:39 -06:00
/* MMIO Base/Limit */
pci_write_config_dword(dev, PCI_MEMORY_BASE, 0x0000fff0);
/* Prefetchable MMIO Base/Limit */
pci_write_config_dword(dev, PCI_PREF_LIMIT_UPPER32, 0);
pci_write_config_dword(dev, PCI_PREF_MEMORY_BASE, 0x0000fff0);
pci_write_config_dword(dev, PCI_PREF_BASE_UPPER32, 0xffffffff);
}
PCI : ability to relocate assigned pci-resources Currently pci-bridges are allocated enough resources to satisfy their immediate requirements. Any additional resource-requests fail if additional free space, contiguous to the one already allocated, is not available. This behavior is not reasonable since sufficient contiguous resources, that can satisfy the request, are available at a different location. This patch provides the ability to expand and relocate a allocated resource. v2: Changelog: Fixed size calculation in pci_reassign_resource() v3: Changelog : Split this patch. The resource.c changes are already upstream. All the pci driver changes are in here. Signed-off-by: Ram Pai <linuxram@us.ibm.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-07-25 14:08:39 -06:00
x86/PCI: Convert maintaining FW-assigned BIOS BAR values to use a list This patch converts the underlying maintenance aspects of FW-assigned BIOS BAR values from a statically allocated array within struct pci_dev to a list of temporary, stand alone, entries. Signed-off-by: Myron Stowe <myron.stowe@redhat.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-11-21 11:54:19 -07:00
/*
* Generic function that returns a value indicating that the device's
* original BIOS BAR address was not saved and so is not available for
* reinstatement.
*
* Can be over-ridden by architecture specific code that implements
* reinstatement functionality rather than leaving it disabled when
* normal allocation attempts fail.
*/
resource_size_t __weak pcibios_retrieve_fw_addr(struct pci_dev *dev, int idx)
{
return 0;
}
PCI: Fix whitespace, capitalization, and spelling errors Fix whitespace, capitalization, and spelling errors. No functional change. I know "busses" is not an error, but "buses" was more common, so I used it consistently. Signed-off-by: Marta Rybczynska <rybczynska@gmail.com> (pci_reset_bridge_secondary_bus()) Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2013-11-14 11:28:18 -07:00
static int pci_revert_fw_address(struct resource *res, struct pci_dev *dev,
PCI : ability to relocate assigned pci-resources Currently pci-bridges are allocated enough resources to satisfy their immediate requirements. Any additional resource-requests fail if additional free space, contiguous to the one already allocated, is not available. This behavior is not reasonable since sufficient contiguous resources, that can satisfy the request, are available at a different location. This patch provides the ability to expand and relocate a allocated resource. v2: Changelog: Fixed size calculation in pci_reassign_resource() v3: Changelog : Split this patch. The resource.c changes are already upstream. All the pci driver changes are in here. Signed-off-by: Ram Pai <linuxram@us.ibm.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-07-25 14:08:39 -06:00
int resno, resource_size_t size)
{
struct resource *root, *conflict;
x86/PCI: Convert maintaining FW-assigned BIOS BAR values to use a list This patch converts the underlying maintenance aspects of FW-assigned BIOS BAR values from a statically allocated array within struct pci_dev to a list of temporary, stand alone, entries. Signed-off-by: Myron Stowe <myron.stowe@redhat.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-11-21 11:54:19 -07:00
resource_size_t fw_addr, start, end;
PCI: fall back to original BIOS BAR addresses If we fail to assign resources to a PCI BAR, this patch makes us try the original address from BIOS rather than leaving it disabled. Linux tries to make sure all PCI device BARs are inside the upstream PCI host bridge or P2P bridge apertures, reassigning BARs if necessary. Windows does similar reassignment. Before this patch, if we could not move a BAR into an aperture, we left the resource unassigned, i.e., at address zero. Windows leaves such BARs at the original BIOS addresses, and this patch makes Linux do the same. This is a bit ugly because we disable the resource long before we try to reassign it, so we have to keep track of the BIOS BAR address somewhere. For lack of a better place, I put it in the struct pci_dev. I think it would be cleaner to attempt the assignment immediately when the claim fails, so we could easily remember the original address. But we currently claim motherboard resources in the middle, after attempting to claim PCI resources and before assigning new PCI resources, and changing that is a fairly big job. Addresses https://bugzilla.kernel.org/show_bug.cgi?id=16263 Reported-by: Andrew <nitr0@seti.kr.ua> Tested-by: Andrew <nitr0@seti.kr.ua> Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-07-15 09:41:42 -06:00
x86/PCI: Convert maintaining FW-assigned BIOS BAR values to use a list This patch converts the underlying maintenance aspects of FW-assigned BIOS BAR values from a statically allocated array within struct pci_dev to a list of temporary, stand alone, entries. Signed-off-by: Myron Stowe <myron.stowe@redhat.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-11-21 11:54:19 -07:00
fw_addr = pcibios_retrieve_fw_addr(dev, resno);
if (!fw_addr)
PCI: Return conventional error values from pci_revert_fw_address() Previously we returned zero for success or 1 for failure. This changes that so we return zero for success or a negative errno for failure. No functional change. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2014-07-08 16:00:42 -06:00
return -ENOMEM;
x86/PCI: Convert maintaining FW-assigned BIOS BAR values to use a list This patch converts the underlying maintenance aspects of FW-assigned BIOS BAR values from a statically allocated array within struct pci_dev to a list of temporary, stand alone, entries. Signed-off-by: Myron Stowe <myron.stowe@redhat.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-11-21 11:54:19 -07:00
PCI : ability to relocate assigned pci-resources Currently pci-bridges are allocated enough resources to satisfy their immediate requirements. Any additional resource-requests fail if additional free space, contiguous to the one already allocated, is not available. This behavior is not reasonable since sufficient contiguous resources, that can satisfy the request, are available at a different location. This patch provides the ability to expand and relocate a allocated resource. v2: Changelog: Fixed size calculation in pci_reassign_resource() v3: Changelog : Split this patch. The resource.c changes are already upstream. All the pci driver changes are in here. Signed-off-by: Ram Pai <linuxram@us.ibm.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-07-25 14:08:39 -06:00
start = res->start;
end = res->end;
x86/PCI: Convert maintaining FW-assigned BIOS BAR values to use a list This patch converts the underlying maintenance aspects of FW-assigned BIOS BAR values from a statically allocated array within struct pci_dev to a list of temporary, stand alone, entries. Signed-off-by: Myron Stowe <myron.stowe@redhat.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-11-21 11:54:19 -07:00
res->start = fw_addr;
PCI : ability to relocate assigned pci-resources Currently pci-bridges are allocated enough resources to satisfy their immediate requirements. Any additional resource-requests fail if additional free space, contiguous to the one already allocated, is not available. This behavior is not reasonable since sufficient contiguous resources, that can satisfy the request, are available at a different location. This patch provides the ability to expand and relocate a allocated resource. v2: Changelog: Fixed size calculation in pci_reassign_resource() v3: Changelog : Split this patch. The resource.c changes are already upstream. All the pci driver changes are in here. Signed-off-by: Ram Pai <linuxram@us.ibm.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-07-25 14:08:39 -06:00
res->end = res->start + size - 1;
PCI: Clear IORESOURCE_UNSET when reverting to firmware-assigned address If pci_assign_resource() fails to assign space for a BAR, we may restore the BAR to whatever firmware left there at boot-time (this depends on whether the arch implements pcibios_retrieve_fw_addr()). The messages we print are not as useful as they could be: pci 0000:00:01.0: BAR 15: assigned [mem 0xc0000000-0xc01fffff 64bit pref] pci 0000:01:00.0: BAR 0: no space for [mem size 0x10000000 pref] pci 0000:01:00.0: BAR 0: trying firmware assignment [mem size 0x10000000 pref] pci 0000:01:00.0: BAR 0: [mem size 0x10000000 pref] conflicts with PCI Bus 0000:00 [mem 0xc0000000-0xffffffff window] The last two lines should contain the actual BAR address, not the size. Clear IORESOURCE_UNSET so we print the address. If requesting the firmware-assigned resource fails, mark it IORESOURCE_UNSET again. This is a cosmetic change to clarify the message: previously, if pci_revert_fw_address() succeeded, pci_assign_resource() cleared IORESOURCE_UNSET anyway, so this isn't really a functional change. Link: https://bugzilla.kernel.org/show_bug.cgi?id=85491#c50 Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2015-09-21 17:26:45 -06:00
res->flags &= ~IORESOURCE_UNSET;
PCI: Fix starting basis for resource requests pci_revert_fw_address() is used to reinstate a PCI device's original FW-assigned BIOS BAR value(s) if normal resource assignment fails. When attempting to reinstate an address, the point within the resource tree from which to attempt the new resource request should be the parent resource corresponding to the device, not the base of the resource tree (ioport_resource or iomem_resource). For PCI devices this would typically be the resource corresponding to the upstream PCI host bridge or P2P bridge aperture. This patch sets the point within the resource tree to attempt a new resource assignment request to the PCI device's parent resource and only if that fails does it fall back to the base ioport_resource or iomem_resource. Signed-off-by: Myron Stowe <myron.stowe@redhat.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-11-21 11:54:07 -07:00
root = pci_find_parent_resource(dev, res);
if (!root) {
if (res->flags & IORESOURCE_IO)
root = &ioport_resource;
else
root = &iomem_resource;
}
PCI : ability to relocate assigned pci-resources Currently pci-bridges are allocated enough resources to satisfy their immediate requirements. Any additional resource-requests fail if additional free space, contiguous to the one already allocated, is not available. This behavior is not reasonable since sufficient contiguous resources, that can satisfy the request, are available at a different location. This patch provides the ability to expand and relocate a allocated resource. v2: Changelog: Fixed size calculation in pci_reassign_resource() v3: Changelog : Split this patch. The resource.c changes are already upstream. All the pci driver changes are in here. Signed-off-by: Ram Pai <linuxram@us.ibm.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-07-25 14:08:39 -06:00
dev_info(&dev->dev, "BAR %d: trying firmware assignment %pR\n",
resno, res);
conflict = request_resource_conflict(root, res);
if (conflict) {
PCI: Return conventional error values from pci_revert_fw_address() Previously we returned zero for success or 1 for failure. This changes that so we return zero for success or a negative errno for failure. No functional change. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2014-07-08 16:00:42 -06:00
dev_info(&dev->dev, "BAR %d: %pR conflicts with %s %pR\n",
resno, res, conflict->name, conflict);
PCI : ability to relocate assigned pci-resources Currently pci-bridges are allocated enough resources to satisfy their immediate requirements. Any additional resource-requests fail if additional free space, contiguous to the one already allocated, is not available. This behavior is not reasonable since sufficient contiguous resources, that can satisfy the request, are available at a different location. This patch provides the ability to expand and relocate a allocated resource. v2: Changelog: Fixed size calculation in pci_reassign_resource() v3: Changelog : Split this patch. The resource.c changes are already upstream. All the pci driver changes are in here. Signed-off-by: Ram Pai <linuxram@us.ibm.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-07-25 14:08:39 -06:00
res->start = start;
res->end = end;
PCI: Clear IORESOURCE_UNSET when reverting to firmware-assigned address If pci_assign_resource() fails to assign space for a BAR, we may restore the BAR to whatever firmware left there at boot-time (this depends on whether the arch implements pcibios_retrieve_fw_addr()). The messages we print are not as useful as they could be: pci 0000:00:01.0: BAR 15: assigned [mem 0xc0000000-0xc01fffff 64bit pref] pci 0000:01:00.0: BAR 0: no space for [mem size 0x10000000 pref] pci 0000:01:00.0: BAR 0: trying firmware assignment [mem size 0x10000000 pref] pci 0000:01:00.0: BAR 0: [mem size 0x10000000 pref] conflicts with PCI Bus 0000:00 [mem 0xc0000000-0xffffffff window] The last two lines should contain the actual BAR address, not the size. Clear IORESOURCE_UNSET so we print the address. If requesting the firmware-assigned resource fails, mark it IORESOURCE_UNSET again. This is a cosmetic change to clarify the message: previously, if pci_revert_fw_address() succeeded, pci_assign_resource() cleared IORESOURCE_UNSET anyway, so this isn't really a functional change. Link: https://bugzilla.kernel.org/show_bug.cgi?id=85491#c50 Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2015-09-21 17:26:45 -06:00
res->flags |= IORESOURCE_UNSET;
PCI: Return conventional error values from pci_revert_fw_address() Previously we returned zero for success or 1 for failure. This changes that so we return zero for success or a negative errno for failure. No functional change. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2014-07-08 16:00:42 -06:00
return -EBUSY;
PCI : ability to relocate assigned pci-resources Currently pci-bridges are allocated enough resources to satisfy their immediate requirements. Any additional resource-requests fail if additional free space, contiguous to the one already allocated, is not available. This behavior is not reasonable since sufficient contiguous resources, that can satisfy the request, are available at a different location. This patch provides the ability to expand and relocate a allocated resource. v2: Changelog: Fixed size calculation in pci_reassign_resource() v3: Changelog : Split this patch. The resource.c changes are already upstream. All the pci driver changes are in here. Signed-off-by: Ram Pai <linuxram@us.ibm.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-07-25 14:08:39 -06:00
}
PCI: Return conventional error values from pci_revert_fw_address() Previously we returned zero for success or 1 for failure. This changes that so we return zero for success or a negative errno for failure. No functional change. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2014-07-08 16:00:42 -06:00
return 0;
PCI : ability to relocate assigned pci-resources Currently pci-bridges are allocated enough resources to satisfy their immediate requirements. Any additional resource-requests fail if additional free space, contiguous to the one already allocated, is not available. This behavior is not reasonable since sufficient contiguous resources, that can satisfy the request, are available at a different location. This patch provides the ability to expand and relocate a allocated resource. v2: Changelog: Fixed size calculation in pci_reassign_resource() v3: Changelog : Split this patch. The resource.c changes are already upstream. All the pci driver changes are in here. Signed-off-by: Ram Pai <linuxram@us.ibm.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-07-25 14:08:39 -06:00
}
PCI: Add a generic weak pcibios_align_resource() Multiple architectures define this as a trivial function, and I'm adding another one as part of the RISC-V port. Add a __weak version of pcibios_align_resource() and delete the now-obselete ones in a handful of ports. The only functional change should be that a handful of ports used to export pcibios_fixup_bus(). Only some architectures export this, so I just dropped it. Signed-off-by: Palmer Dabbelt <palmer@dabbelt.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2017-08-02 13:44:50 -06:00
/*
* We don't have to worry about legacy ISA devices, so nothing to do here.
* This is marked as __weak because multiple architectures define it; it should
* eventually go away.
*/
resource_size_t __weak pcibios_align_resource(void *data,
const struct resource *res,
resource_size_t size,
resource_size_t align)
{
return res->start;
}
PCI: reorder __pci_assign_resource() (no change) Reorder functions so __pci_assign_resource(), _pci_assign_resource(), and pci_assign_resource() are closer together. No code change. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2012-07-11 17:05:43 -06:00
static int __pci_assign_resource(struct pci_bus *bus, struct pci_dev *dev,
int resno, resource_size_t size, resource_size_t align)
{
struct resource *res = dev->resource + resno;
resource_size_t min;
int ret;
min = (res->flags & IORESOURCE_IO) ? PCIBIOS_MIN_IO : PCIBIOS_MIN_MEM;
PCI: Add resource allocation comments Add comments in the code to match the allocation strategy of 7c671426dfc3 ("PCI: Restrict 64-bit prefetchable bridge windows to 64-bit resources"). No functional change. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2014-05-19 18:32:18 -06:00
/*
* First, try exact prefetching match. Even if a 64-bit
* prefetchable bridge window is below 4GB, we can't put a 32-bit
* prefetchable resource in it because pbus_size_mem() assumes a
* 64-bit window will contain no 32-bit resources. If we assign
* things differently than they were sized, not everything will fit.
*/
PCI: reorder __pci_assign_resource() (no change) Reorder functions so __pci_assign_resource(), _pci_assign_resource(), and pci_assign_resource() are closer together. No code change. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2012-07-11 17:05:43 -06:00
ret = pci_bus_alloc_resource(bus, res, size, align, min,
PCI: Restrict 64-bit prefetchable bridge windows to 64-bit resources This patch changes the way we handle 64-bit prefetchable bridge windows to make it more likely that we can assign space to all devices. Previously we put all prefetchable resources in the prefetchable bridge window. If any of those resources was 32-bit only, we restricted the window to be below 4GB. After this patch, we only put 64-bit prefetchable resources in a 64-bit prefetchable window. We put all 32-bit prefetchable resources in the non-prefetchable window, even if there are no 64-bit prefetchable resources. With the previous approach, if there was a 32-bit prefetchable resource behind a bridge, we forced the bridge's prefetchable window below 4GB, which meant that even if there was plenty of space above 4GB available, we couldn't use it, and assignment of large 64-bit resources could fail, as in the bugzilla below. The new strategy is: 1) If the prefetchable window is 64 bits wide, we put only 64-bit prefetchable resources in it. Any 32-bit prefetchable resources go in the non-prefetchable window. 2) If the prefetchable window is 32 bits wide, we put both 32- and 64-bit prefetchable resources in it. 3) If there is no prefetchable window, all MMIO resources go in the non-prefetchable window. This reduces performance for 32-bit prefetchable resources below a bridge with a 64-bit prefetchable window. We previously assigned prefetchable space, but now we'll assign non-prefetchable space. This is the case even if there are no 64-bit prefetchable resources, or if they would all fit below 4GB. In those cases, the old strategy would work and would have better performance. [bhelgaas: write changelog, add bugzilla link, fold in mem64_mask removal] Link: https://bugzilla.kernel.org/show_bug.cgi?id=74151 Tested-by: Guo Chao <yan@linux.vnet.ibm.com> Tested-by: Wei Yang <weiyang@linux.vnet.ibm.com> Signed-off-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2014-05-19 17:01:55 -06:00
IORESOURCE_PREFETCH | IORESOURCE_MEM_64,
PCI: reorder __pci_assign_resource() (no change) Reorder functions so __pci_assign_resource(), _pci_assign_resource(), and pci_assign_resource() are closer together. No code change. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2012-07-11 17:05:43 -06:00
pcibios_align_resource, dev);
PCI: Simplify __pci_assign_resource() coding style If an allocation succeeds, we can return success immediately. Then we don't have to test for success in the subsequent code. No functional change. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2014-05-19 18:39:07 -06:00
if (ret == 0)
return 0;
PCI: reorder __pci_assign_resource() (no change) Reorder functions so __pci_assign_resource(), _pci_assign_resource(), and pci_assign_resource() are closer together. No code change. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2012-07-11 17:05:43 -06:00
PCI: Add resource allocation comments Add comments in the code to match the allocation strategy of 7c671426dfc3 ("PCI: Restrict 64-bit prefetchable bridge windows to 64-bit resources"). No functional change. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2014-05-19 18:32:18 -06:00
/*
* If the prefetchable window is only 32 bits wide, we can put
* 64-bit prefetchable resources in it.
*/
PCI: Simplify __pci_assign_resource() coding style If an allocation succeeds, we can return success immediately. Then we don't have to test for success in the subsequent code. No functional change. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2014-05-19 18:39:07 -06:00
if ((res->flags & (IORESOURCE_PREFETCH | IORESOURCE_MEM_64)) ==
PCI: Restrict 64-bit prefetchable bridge windows to 64-bit resources This patch changes the way we handle 64-bit prefetchable bridge windows to make it more likely that we can assign space to all devices. Previously we put all prefetchable resources in the prefetchable bridge window. If any of those resources was 32-bit only, we restricted the window to be below 4GB. After this patch, we only put 64-bit prefetchable resources in a 64-bit prefetchable window. We put all 32-bit prefetchable resources in the non-prefetchable window, even if there are no 64-bit prefetchable resources. With the previous approach, if there was a 32-bit prefetchable resource behind a bridge, we forced the bridge's prefetchable window below 4GB, which meant that even if there was plenty of space above 4GB available, we couldn't use it, and assignment of large 64-bit resources could fail, as in the bugzilla below. The new strategy is: 1) If the prefetchable window is 64 bits wide, we put only 64-bit prefetchable resources in it. Any 32-bit prefetchable resources go in the non-prefetchable window. 2) If the prefetchable window is 32 bits wide, we put both 32- and 64-bit prefetchable resources in it. 3) If there is no prefetchable window, all MMIO resources go in the non-prefetchable window. This reduces performance for 32-bit prefetchable resources below a bridge with a 64-bit prefetchable window. We previously assigned prefetchable space, but now we'll assign non-prefetchable space. This is the case even if there are no 64-bit prefetchable resources, or if they would all fit below 4GB. In those cases, the old strategy would work and would have better performance. [bhelgaas: write changelog, add bugzilla link, fold in mem64_mask removal] Link: https://bugzilla.kernel.org/show_bug.cgi?id=74151 Tested-by: Guo Chao <yan@linux.vnet.ibm.com> Tested-by: Wei Yang <weiyang@linux.vnet.ibm.com> Signed-off-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2014-05-19 17:01:55 -06:00
(IORESOURCE_PREFETCH | IORESOURCE_MEM_64)) {
ret = pci_bus_alloc_resource(bus, res, size, align, min,
IORESOURCE_PREFETCH,
PCI: reorder __pci_assign_resource() (no change) Reorder functions so __pci_assign_resource(), _pci_assign_resource(), and pci_assign_resource() are closer together. No code change. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2012-07-11 17:05:43 -06:00
pcibios_align_resource, dev);
PCI: Simplify __pci_assign_resource() coding style If an allocation succeeds, we can return success immediately. Then we don't have to test for success in the subsequent code. No functional change. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2014-05-19 18:39:07 -06:00
if (ret == 0)
return 0;
PCI: reorder __pci_assign_resource() (no change) Reorder functions so __pci_assign_resource(), _pci_assign_resource(), and pci_assign_resource() are closer together. No code change. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2012-07-11 17:05:43 -06:00
}
PCI: Restrict 64-bit prefetchable bridge windows to 64-bit resources This patch changes the way we handle 64-bit prefetchable bridge windows to make it more likely that we can assign space to all devices. Previously we put all prefetchable resources in the prefetchable bridge window. If any of those resources was 32-bit only, we restricted the window to be below 4GB. After this patch, we only put 64-bit prefetchable resources in a 64-bit prefetchable window. We put all 32-bit prefetchable resources in the non-prefetchable window, even if there are no 64-bit prefetchable resources. With the previous approach, if there was a 32-bit prefetchable resource behind a bridge, we forced the bridge's prefetchable window below 4GB, which meant that even if there was plenty of space above 4GB available, we couldn't use it, and assignment of large 64-bit resources could fail, as in the bugzilla below. The new strategy is: 1) If the prefetchable window is 64 bits wide, we put only 64-bit prefetchable resources in it. Any 32-bit prefetchable resources go in the non-prefetchable window. 2) If the prefetchable window is 32 bits wide, we put both 32- and 64-bit prefetchable resources in it. 3) If there is no prefetchable window, all MMIO resources go in the non-prefetchable window. This reduces performance for 32-bit prefetchable resources below a bridge with a 64-bit prefetchable window. We previously assigned prefetchable space, but now we'll assign non-prefetchable space. This is the case even if there are no 64-bit prefetchable resources, or if they would all fit below 4GB. In those cases, the old strategy would work and would have better performance. [bhelgaas: write changelog, add bugzilla link, fold in mem64_mask removal] Link: https://bugzilla.kernel.org/show_bug.cgi?id=74151 Tested-by: Guo Chao <yan@linux.vnet.ibm.com> Tested-by: Wei Yang <weiyang@linux.vnet.ibm.com> Signed-off-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2014-05-19 17:01:55 -06:00
PCI: Add resource allocation comments Add comments in the code to match the allocation strategy of 7c671426dfc3 ("PCI: Restrict 64-bit prefetchable bridge windows to 64-bit resources"). No functional change. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2014-05-19 18:32:18 -06:00
/*
* If we didn't find a better match, we can put any memory resource
* in a non-prefetchable window. If this resource is 32 bits and
* non-prefetchable, the first call already tried the only possibility
* so we don't need to try again.
*/
if (res->flags & (IORESOURCE_PREFETCH | IORESOURCE_MEM_64))
PCI: reorder __pci_assign_resource() (no change) Reorder functions so __pci_assign_resource(), _pci_assign_resource(), and pci_assign_resource() are closer together. No code change. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2012-07-11 17:05:43 -06:00
ret = pci_bus_alloc_resource(bus, res, size, align, min, 0,
pcibios_align_resource, dev);
PCI: Add resource allocation comments Add comments in the code to match the allocation strategy of 7c671426dfc3 ("PCI: Restrict 64-bit prefetchable bridge windows to 64-bit resources"). No functional change. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2014-05-19 18:32:18 -06:00
PCI: reorder __pci_assign_resource() (no change) Reorder functions so __pci_assign_resource(), _pci_assign_resource(), and pci_assign_resource() are closer together. No code change. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2012-07-11 17:05:43 -06:00
return ret;
}
PCI: fix truncation of resource size to 32 bits _pci_assign_resource() took an int "size" argument, which meant that sizes larger than 4GB were truncated. Change type to resource_size_t. [bhelgaas: changelog] Signed-off-by: Nikhil P Rao <nikhil.rao@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2012-06-20 13:56:00 -06:00
static int _pci_assign_resource(struct pci_dev *dev, int resno,
resource_size_t size, resource_size_t min_align)
PCI : ability to relocate assigned pci-resources Currently pci-bridges are allocated enough resources to satisfy their immediate requirements. Any additional resource-requests fail if additional free space, contiguous to the one already allocated, is not available. This behavior is not reasonable since sufficient contiguous resources, that can satisfy the request, are available at a different location. This patch provides the ability to expand and relocate a allocated resource. v2: Changelog: Fixed size calculation in pci_reassign_resource() v3: Changelog : Split this patch. The resource.c changes are already upstream. All the pci driver changes are in here. Signed-off-by: Ram Pai <linuxram@us.ibm.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-07-25 14:08:39 -06:00
{
struct pci_bus *bus;
int ret;
PCI: fall back to original BIOS BAR addresses If we fail to assign resources to a PCI BAR, this patch makes us try the original address from BIOS rather than leaving it disabled. Linux tries to make sure all PCI device BARs are inside the upstream PCI host bridge or P2P bridge apertures, reassigning BARs if necessary. Windows does similar reassignment. Before this patch, if we could not move a BAR into an aperture, we left the resource unassigned, i.e., at address zero. Windows leaves such BARs at the original BIOS addresses, and this patch makes Linux do the same. This is a bit ugly because we disable the resource long before we try to reassign it, so we have to keep track of the BIOS BAR address somewhere. For lack of a better place, I put it in the struct pci_dev. I think it would be cleaner to attempt the assignment immediately when the claim fails, so we could easily remember the original address. But we currently claim motherboard resources in the middle, after attempting to claim PCI resources and before assigning new PCI resources, and changing that is a fairly big job. Addresses https://bugzilla.kernel.org/show_bug.cgi?id=16263 Reported-by: Andrew <nitr0@seti.kr.ua> Tested-by: Andrew <nitr0@seti.kr.ua> Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-07-15 09:41:42 -06:00
PCI : ability to relocate assigned pci-resources Currently pci-bridges are allocated enough resources to satisfy their immediate requirements. Any additional resource-requests fail if additional free space, contiguous to the one already allocated, is not available. This behavior is not reasonable since sufficient contiguous resources, that can satisfy the request, are available at a different location. This patch provides the ability to expand and relocate a allocated resource. v2: Changelog: Fixed size calculation in pci_reassign_resource() v3: Changelog : Split this patch. The resource.c changes are already upstream. All the pci driver changes are in here. Signed-off-by: Ram Pai <linuxram@us.ibm.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-07-25 14:08:39 -06:00
bus = dev->bus;
while ((ret = __pci_assign_resource(bus, dev, resno, size, min_align))) {
if (!bus->parent || !bus->self->transparent)
break;
bus = bus->parent;
}
return ret;
}
PCI: improve resource allocation under transparent bridges We could run out of space under under 4g, but devices under transparent bridges can use 64bit resources, so keep trying on the parent bus until we hit a non-transparent bridge. Impact: better support for assigning unassigned resources Reviewed-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Signed-off-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-04-23 21:49:25 -06:00
int pci_assign_resource(struct pci_dev *dev, int resno)
{
struct resource *res = dev->resource + resno;
PCI : ability to relocate assigned pci-resources Currently pci-bridges are allocated enough resources to satisfy their immediate requirements. Any additional resource-requests fail if additional free space, contiguous to the one already allocated, is not available. This behavior is not reasonable since sufficient contiguous resources, that can satisfy the request, are available at a different location. This patch provides the ability to expand and relocate a allocated resource. v2: Changelog: Fixed size calculation in pci_reassign_resource() v3: Changelog : Split this patch. The resource.c changes are already upstream. All the pci driver changes are in here. Signed-off-by: Ram Pai <linuxram@us.ibm.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-07-25 14:08:39 -06:00
resource_size_t align, size;
PCI: improve resource allocation under transparent bridges We could run out of space under under 4g, but devices under transparent bridges can use 64bit resources, so keep trying on the parent bus until we hit a non-transparent bridge. Impact: better support for assigning unassigned resources Reviewed-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Signed-off-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-04-23 21:49:25 -06:00
int ret;
PCI: Don't assign or reassign immutable resources IORESOURCE_PCI_FIXED means the resource can't be moved, so if it's set, don't bother trying to assign or reassign the resource. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2016-03-01 09:58:04 -07:00
if (res->flags & IORESOURCE_PCI_FIXED)
return 0;
PCI: Mark resources as IORESOURCE_UNSET if we can't assign them When assigning addresses to resources, mark them with IORESOURCE_UNSET before we start and clear IORESOURCE_UNSET if assignment is successful. That means that if we print the resource during assignment, we will show the size, not a meaningless address. Also, clear IORESOURCE_UNSET if we do assign an address, so we print the address when it is valid. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2014-02-26 11:25:58 -07:00
res->flags |= IORESOURCE_UNSET;
PCI SR-IOV: correct broken resource alignment calculations An SR-IOV capable device includes an SR-IOV PCIe capability which describes the Virtual Function (VF) BAR requirements. A typical SR-IOV device can support multiple VFs whose BARs must be in a contiguous region, effectively an array of VF BARs. The BAR reports the size requirement for a single VF. We calculate the full range needed by simply multiplying the VF BAR size with the number of possible VFs and create a resource spanning the full range. This all seems sane enough except it artificially inflates the alignment requirement for the VF BAR. The VF BAR need only be aligned to the size of a single BAR not the contiguous range of VF BARs. This can cause us to fail to allocate resources for the BAR despite the fact that we actually have enough space. This patch adds a thin PCI specific layer over the generic resource_alignment() function which is aware of the special nature of VF BARs and does sorting and allocation based on the smaller alignment requirement. I recognize that while resource_alignment is generic, it's basically a PCI helper. An alternative to this patch is to add PCI VF BAR specific information to struct resource. I opted for the extra layer rather than adding such PCI specific information to struct resource. This does have the slight downside that we don't cache the BAR size and re-read for each alignment query (happens a small handful of times during boot for each VF BAR). Signed-off-by: Chris Wright <chrisw@sous-sol.org> Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Matthew Wilcox <matthew@wil.cx> Cc: Yu Zhao <yu.zhao@intel.com> Cc: stable@kernel.org Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-08-28 14:00:06 -06:00
align = pci_resource_alignment(dev, res);
PCI: improve resource allocation under transparent bridges We could run out of space under under 4g, but devices under transparent bridges can use 64bit resources, so keep trying on the parent bus until we hit a non-transparent bridge. Impact: better support for assigning unassigned resources Reviewed-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Signed-off-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-04-23 21:49:25 -06:00
if (!align) {
PCI: Merge multi-line quoted strings Merge quoted strings that are broken across lines into a single entity. The compiler merges them anyway, but checkpatch complains about it, and merging them makes it easier to grep for strings. No functional change. [bhelgaas: changelog, do the same for everything under drivers/pci] Signed-off-by: Ryan Desfosses <ryan@desfo.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2014-04-18 18:13:50 -06:00
dev_info(&dev->dev, "BAR %d: can't assign %pR (bogus alignment)\n",
resno, res);
PCI: improve resource allocation under transparent bridges We could run out of space under under 4g, but devices under transparent bridges can use 64bit resources, so keep trying on the parent bus until we hit a non-transparent bridge. Impact: better support for assigning unassigned resources Reviewed-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Signed-off-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-04-23 21:49:25 -06:00
return -EINVAL;
}
PCI : ability to relocate assigned pci-resources Currently pci-bridges are allocated enough resources to satisfy their immediate requirements. Any additional resource-requests fail if additional free space, contiguous to the one already allocated, is not available. This behavior is not reasonable since sufficient contiguous resources, that can satisfy the request, are available at a different location. This patch provides the ability to expand and relocate a allocated resource. v2: Changelog: Fixed size calculation in pci_reassign_resource() v3: Changelog : Split this patch. The resource.c changes are already upstream. All the pci driver changes are in here. Signed-off-by: Ram Pai <linuxram@us.ibm.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-07-25 14:08:39 -06:00
size = resource_size(res);
ret = _pci_assign_resource(dev, resno, size, align);
PCI: improve resource allocation under transparent bridges We could run out of space under under 4g, but devices under transparent bridges can use 64bit resources, so keep trying on the parent bus until we hit a non-transparent bridge. Impact: better support for assigning unassigned resources Reviewed-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Signed-off-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-04-23 21:49:25 -06:00
PCI : ability to relocate assigned pci-resources Currently pci-bridges are allocated enough resources to satisfy their immediate requirements. Any additional resource-requests fail if additional free space, contiguous to the one already allocated, is not available. This behavior is not reasonable since sufficient contiguous resources, that can satisfy the request, are available at a different location. This patch provides the ability to expand and relocate a allocated resource. v2: Changelog: Fixed size calculation in pci_reassign_resource() v3: Changelog : Split this patch. The resource.c changes are already upstream. All the pci driver changes are in here. Signed-off-by: Ram Pai <linuxram@us.ibm.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-07-25 14:08:39 -06:00
/*
* If we failed to assign anything, let's try the address
* where firmware left it. That at least has a chance of
* working, which is better than just leaving it disabled.
*/
PCI: Tidy resource assignment messages Print messages about failures in pci_assign_resource(). We can drop the "by-hand" message from _pci_assign_resource() because %pR now prints the size rather than the address if the resource hasn't been assigned. No functional change. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2014-07-08 16:04:22 -06:00
if (ret < 0) {
dev_info(&dev->dev, "BAR %d: no space for %pR\n", resno, res);
PCI : ability to relocate assigned pci-resources Currently pci-bridges are allocated enough resources to satisfy their immediate requirements. Any additional resource-requests fail if additional free space, contiguous to the one already allocated, is not available. This behavior is not reasonable since sufficient contiguous resources, that can satisfy the request, are available at a different location. This patch provides the ability to expand and relocate a allocated resource. v2: Changelog: Fixed size calculation in pci_reassign_resource() v3: Changelog : Split this patch. The resource.c changes are already upstream. All the pci driver changes are in here. Signed-off-by: Ram Pai <linuxram@us.ibm.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-07-25 14:08:39 -06:00
ret = pci_revert_fw_address(res, dev, resno, size);
PCI: Tidy resource assignment messages Print messages about failures in pci_assign_resource(). We can drop the "by-hand" message from _pci_assign_resource() because %pR now prints the size rather than the address if the resource hasn't been assigned. No functional change. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2014-07-08 16:04:22 -06:00
}
PCI: improve resource allocation under transparent bridges We could run out of space under under 4g, but devices under transparent bridges can use 64bit resources, so keep trying on the parent bus until we hit a non-transparent bridge. Impact: better support for assigning unassigned resources Reviewed-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Signed-off-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-04-23 21:49:25 -06:00
PCI: Tidy resource assignment messages Print messages about failures in pci_assign_resource(). We can drop the "by-hand" message from _pci_assign_resource() because %pR now prints the size rather than the address if the resource hasn't been assigned. No functional change. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2014-07-08 16:04:22 -06:00
if (ret < 0) {
dev_info(&dev->dev, "BAR %d: failed to assign %pR\n", resno,
res);
PCI: Cleanup control flow Return errors immediately so the straightline path is the normal, no-error path. No functional change. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2014-07-04 15:58:15 -06:00
return ret;
PCI: Tidy resource assignment messages Print messages about failures in pci_assign_resource(). We can drop the "by-hand" message from _pci_assign_resource() because %pR now prints the size rather than the address if the resource hasn't been assigned. No functional change. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2014-07-08 16:04:22 -06:00
}
PCI: Cleanup control flow Return errors immediately so the straightline path is the normal, no-error path. No functional change. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2014-07-04 15:58:15 -06:00
res->flags &= ~IORESOURCE_UNSET;
res->flags &= ~IORESOURCE_STARTALIGN;
dev_info(&dev->dev, "BAR %d: assigned %pR\n", resno, res);
if (resno < PCI_BRIDGE_RESOURCES)
pci_update_resource(dev, resno);
return 0;
PCI: improve resource allocation under transparent bridges We could run out of space under under 4g, but devices under transparent bridges can use 64bit resources, so keep trying on the parent bus until we hit a non-transparent bridge. Impact: better support for assigning unassigned resources Reviewed-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Signed-off-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-04-23 21:49:25 -06:00
}
PCI: Move EXPORT_SYMBOL so it immediately follows function/variable Move EXPORT_SYMBOL so it immediately follows the function or variable. No functional change. [bhelgaas: squash similar changes, fix hotplug, probe, rom, search, too] Signed-off-by: Ryan Desfosses <ryan@desfo.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2014-04-25 14:32:25 -06:00
EXPORT_SYMBOL(pci_assign_resource);
PCI: improve resource allocation under transparent bridges We could run out of space under under 4g, but devices under transparent bridges can use 64bit resources, so keep trying on the parent bus until we hit a non-transparent bridge. Impact: better support for assigning unassigned resources Reviewed-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Signed-off-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-04-23 21:49:25 -06:00
PCI: reorder __pci_assign_resource() (no change) Reorder functions so __pci_assign_resource(), _pci_assign_resource(), and pci_assign_resource() are closer together. No code change. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2012-07-11 17:05:43 -06:00
int pci_reassign_resource(struct pci_dev *dev, int resno, resource_size_t addsize,
resource_size_t min_align)
{
struct resource *res = dev->resource + resno;
PCI: Keep original resource if we fail to expand it If we have space assigned to a resource, we try to expand the resource (e.g., to accommodate SR-IOV resources), and the expansion attempt fails, we should keep the original assignment. After bd064f0a231a ("PCI: Mark resources as IORESOURCE_UNSET if we can't assign them"), we left the resource marked IORESOURCE_UNSET when the expansion failed, even if it had originally been set. That caused errors like this: pci 0003:00:00.0: can't enable device: BAR 15 [mem size 0x0c000000 64bit pref] not assigned pci 0003:00:00.0: Error enabling bridge (-22), continuing Fix this by restoring the original flags when reassignment fails. [bhelgaas: reworked to simplify, changelog] Fixes: bd064f0a231a ("PCI: Mark resources as IORESOURCE_UNSET if we can't assign them") Signed-off-by: Guo Chao <yan@linux.vnet.ibm.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> CC: stable@vger.kernel.org # v3.15+
2014-07-03 18:30:29 -06:00
unsigned long flags;
PCI: reorder __pci_assign_resource() (no change) Reorder functions so __pci_assign_resource(), _pci_assign_resource(), and pci_assign_resource() are closer together. No code change. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2012-07-11 17:05:43 -06:00
resource_size_t new_size;
int ret;
PCI: Don't assign or reassign immutable resources IORESOURCE_PCI_FIXED means the resource can't be moved, so if it's set, don't bother trying to assign or reassign the resource. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2016-03-01 09:58:04 -07:00
if (res->flags & IORESOURCE_PCI_FIXED)
return 0;
PCI: Keep original resource if we fail to expand it If we have space assigned to a resource, we try to expand the resource (e.g., to accommodate SR-IOV resources), and the expansion attempt fails, we should keep the original assignment. After bd064f0a231a ("PCI: Mark resources as IORESOURCE_UNSET if we can't assign them"), we left the resource marked IORESOURCE_UNSET when the expansion failed, even if it had originally been set. That caused errors like this: pci 0003:00:00.0: can't enable device: BAR 15 [mem size 0x0c000000 64bit pref] not assigned pci 0003:00:00.0: Error enabling bridge (-22), continuing Fix this by restoring the original flags when reassignment fails. [bhelgaas: reworked to simplify, changelog] Fixes: bd064f0a231a ("PCI: Mark resources as IORESOURCE_UNSET if we can't assign them") Signed-off-by: Guo Chao <yan@linux.vnet.ibm.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> CC: stable@vger.kernel.org # v3.15+
2014-07-03 18:30:29 -06:00
flags = res->flags;
PCI: Mark resources as IORESOURCE_UNSET if we can't assign them When assigning addresses to resources, mark them with IORESOURCE_UNSET before we start and clear IORESOURCE_UNSET if assignment is successful. That means that if we print the resource during assignment, we will show the size, not a meaningless address. Also, clear IORESOURCE_UNSET if we do assign an address, so we print the address when it is valid. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2014-02-26 11:25:58 -07:00
res->flags |= IORESOURCE_UNSET;
PCI: reorder __pci_assign_resource() (no change) Reorder functions so __pci_assign_resource(), _pci_assign_resource(), and pci_assign_resource() are closer together. No code change. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2012-07-11 17:05:43 -06:00
if (!res->parent) {
PCI: Merge multi-line quoted strings Merge quoted strings that are broken across lines into a single entity. The compiler merges them anyway, but checkpatch complains about it, and merging them makes it easier to grep for strings. No functional change. [bhelgaas: changelog, do the same for everything under drivers/pci] Signed-off-by: Ryan Desfosses <ryan@desfo.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2014-04-18 18:13:50 -06:00
dev_info(&dev->dev, "BAR %d: can't reassign an unassigned resource %pR\n",
resno, res);
PCI: reorder __pci_assign_resource() (no change) Reorder functions so __pci_assign_resource(), _pci_assign_resource(), and pci_assign_resource() are closer together. No code change. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2012-07-11 17:05:43 -06:00
return -EINVAL;
}
/* already aligned with min_align */
new_size = resource_size(res) + addsize;
ret = _pci_assign_resource(dev, resno, new_size, min_align);
PCI: Cleanup control flow Return errors immediately so the straightline path is the normal, no-error path. No functional change. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2014-07-04 15:58:15 -06:00
if (ret) {
PCI: Keep original resource if we fail to expand it If we have space assigned to a resource, we try to expand the resource (e.g., to accommodate SR-IOV resources), and the expansion attempt fails, we should keep the original assignment. After bd064f0a231a ("PCI: Mark resources as IORESOURCE_UNSET if we can't assign them"), we left the resource marked IORESOURCE_UNSET when the expansion failed, even if it had originally been set. That caused errors like this: pci 0003:00:00.0: can't enable device: BAR 15 [mem size 0x0c000000 64bit pref] not assigned pci 0003:00:00.0: Error enabling bridge (-22), continuing Fix this by restoring the original flags when reassignment fails. [bhelgaas: reworked to simplify, changelog] Fixes: bd064f0a231a ("PCI: Mark resources as IORESOURCE_UNSET if we can't assign them") Signed-off-by: Guo Chao <yan@linux.vnet.ibm.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> CC: stable@vger.kernel.org # v3.15+
2014-07-03 18:30:29 -06:00
res->flags = flags;
dev_info(&dev->dev, "BAR %d: %pR (failed to expand by %#llx)\n",
resno, res, (unsigned long long) addsize);
PCI: Cleanup control flow Return errors immediately so the straightline path is the normal, no-error path. No functional change. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2014-07-04 15:58:15 -06:00
return ret;
PCI: reorder __pci_assign_resource() (no change) Reorder functions so __pci_assign_resource(), _pci_assign_resource(), and pci_assign_resource() are closer together. No code change. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2012-07-11 17:05:43 -06:00
}
PCI: Keep original resource if we fail to expand it If we have space assigned to a resource, we try to expand the resource (e.g., to accommodate SR-IOV resources), and the expansion attempt fails, we should keep the original assignment. After bd064f0a231a ("PCI: Mark resources as IORESOURCE_UNSET if we can't assign them"), we left the resource marked IORESOURCE_UNSET when the expansion failed, even if it had originally been set. That caused errors like this: pci 0003:00:00.0: can't enable device: BAR 15 [mem size 0x0c000000 64bit pref] not assigned pci 0003:00:00.0: Error enabling bridge (-22), continuing Fix this by restoring the original flags when reassignment fails. [bhelgaas: reworked to simplify, changelog] Fixes: bd064f0a231a ("PCI: Mark resources as IORESOURCE_UNSET if we can't assign them") Signed-off-by: Guo Chao <yan@linux.vnet.ibm.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> CC: stable@vger.kernel.org # v3.15+
2014-07-03 18:30:29 -06:00
PCI: Cleanup control flow Return errors immediately so the straightline path is the normal, no-error path. No functional change. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2014-07-04 15:58:15 -06:00
res->flags &= ~IORESOURCE_UNSET;
res->flags &= ~IORESOURCE_STARTALIGN;
PCI: Tidy resource assignment messages Print messages about failures in pci_assign_resource(). We can drop the "by-hand" message from _pci_assign_resource() because %pR now prints the size rather than the address if the resource hasn't been assigned. No functional change. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2014-07-08 16:04:22 -06:00
dev_info(&dev->dev, "BAR %d: reassigned %pR (expanded by %#llx)\n",
resno, res, (unsigned long long) addsize);
PCI: Cleanup control flow Return errors immediately so the straightline path is the normal, no-error path. No functional change. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2014-07-04 15:58:15 -06:00
if (resno < PCI_BRIDGE_RESOURCES)
pci_update_resource(dev, resno);
return 0;
PCI: reorder __pci_assign_resource() (no change) Reorder functions so __pci_assign_resource(), _pci_assign_resource(), and pci_assign_resource() are closer together. No code change. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2012-07-11 17:05:43 -06:00
}
PCI: add generic pci_enable_resources() Each architecture has its own pcibios_enable_resources() implementation. These differ in many minor ways that have nothing to do with actual architectural differences. Follow-on patches will make most arches use this generic version instead. This version is based on powerpc, which seemed most up-to-date. The only functional difference from the x86 version is that this uses "!r->parent" to check for resource collisions instead of "!r->start && r->end". Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by: David Howells <dhowells@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-03-04 11:56:47 -07:00
int pci_enable_resources(struct pci_dev *dev, int mask)
{
u16 cmd, old_cmd;
int i;
struct resource *r;
pci_read_config_word(dev, PCI_COMMAND, &cmd);
old_cmd = cmd;
for (i = 0; i < PCI_NUM_RESOURCES; i++) {
if (!(mask & (1 << i)))
continue;
r = &dev->resource[i];
if (!(r->flags & (IORESOURCE_IO | IORESOURCE_MEM)))
continue;
if ((i == PCI_ROM_RESOURCE) &&
(!(r->flags & IORESOURCE_ROM_ENABLE)))
continue;
PCI: Don't enable decoding if BAR hasn't been assigned an address Don't enable memory or I/O decoding if we haven't assigned or claimed the BAR's resource. If we enable decoding for a BAR that hasn't been assigned an address, we'll likely cause bus conflicts. This declines to enable decoding for resources with IORESOURCE_UNSET. Note that drivers can use pci_enable_device_io() or pci_enable_device_mem() if they only care about specific types of BARs. In that case, we don't bother checking whether the corresponding resources are assigned or claimed. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2014-02-26 11:26:00 -07:00
if (r->flags & IORESOURCE_UNSET) {
dev_err(&dev->dev, "can't enable device: BAR %d %pR not assigned\n",
i, r);
return -EINVAL;
}
PCI: add generic pci_enable_resources() Each architecture has its own pcibios_enable_resources() implementation. These differ in many minor ways that have nothing to do with actual architectural differences. Follow-on patches will make most arches use this generic version instead. This version is based on powerpc, which seemed most up-to-date. The only functional difference from the x86 version is that this uses "!r->parent" to check for resource collisions instead of "!r->start && r->end". Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by: David Howells <dhowells@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-03-04 11:56:47 -07:00
if (!r->parent) {
PCI: Don't enable decoding if BAR hasn't been assigned an address Don't enable memory or I/O decoding if we haven't assigned or claimed the BAR's resource. If we enable decoding for a BAR that hasn't been assigned an address, we'll likely cause bus conflicts. This declines to enable decoding for resources with IORESOURCE_UNSET. Note that drivers can use pci_enable_device_io() or pci_enable_device_mem() if they only care about specific types of BARs. In that case, we don't bother checking whether the corresponding resources are assigned or claimed. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2014-02-26 11:26:00 -07:00
dev_err(&dev->dev, "can't enable device: BAR %d %pR not claimed\n",
i, r);
PCI: add generic pci_enable_resources() Each architecture has its own pcibios_enable_resources() implementation. These differ in many minor ways that have nothing to do with actual architectural differences. Follow-on patches will make most arches use this generic version instead. This version is based on powerpc, which seemed most up-to-date. The only functional difference from the x86 version is that this uses "!r->parent" to check for resource collisions instead of "!r->start && r->end". Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by: David Howells <dhowells@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-03-04 11:56:47 -07:00
return -EINVAL;
}
if (r->flags & IORESOURCE_IO)
cmd |= PCI_COMMAND_IO;
if (r->flags & IORESOURCE_MEM)
cmd |= PCI_COMMAND_MEMORY;
}
if (cmd != old_cmd) {
dev_info(&dev->dev, "enabling device (%04x -> %04x)\n",
old_cmd, cmd);
pci_write_config_word(dev, PCI_COMMAND, cmd);
}
return 0;
}