regulator: qcom_spmi: Add support for SAW
Add support for SAW controlled regulators. The regulators defined as SAW controlled in the device tree will be controlled through special CPU registers instead of direct SPMI accesses. This is required especially for CPU supply regulators to synchronize with clock scaling and for Automatic Voltage Switching. Signed-off-by: Ilia Lin <ilialin@codeaurora.org> Signed-off-by: Mark Brown <broonie@kernel.org>
This commit is contained in:
parent
3012e81446
commit
0caecaa872
|
@ -25,6 +25,8 @@
|
|||
#include <linux/regulator/driver.h>
|
||||
#include <linux/regmap.h>
|
||||
#include <linux/list.h>
|
||||
#include <linux/mfd/syscon.h>
|
||||
#include <linux/io.h>
|
||||
|
||||
/* Pin control enable input pins. */
|
||||
#define SPMI_REGULATOR_PIN_CTRL_ENABLE_NONE 0x00
|
||||
|
@ -181,6 +183,23 @@ enum spmi_boost_byp_registers {
|
|||
SPMI_BOOST_BYP_REG_CURRENT_LIMIT = 0x4b,
|
||||
};
|
||||
|
||||
enum spmi_saw3_registers {
|
||||
SAW3_SECURE = 0x00,
|
||||
SAW3_ID = 0x04,
|
||||
SAW3_SPM_STS = 0x0C,
|
||||
SAW3_AVS_STS = 0x10,
|
||||
SAW3_PMIC_STS = 0x14,
|
||||
SAW3_RST = 0x18,
|
||||
SAW3_VCTL = 0x1C,
|
||||
SAW3_AVS_CTL = 0x20,
|
||||
SAW3_AVS_LIMIT = 0x24,
|
||||
SAW3_AVS_DLY = 0x28,
|
||||
SAW3_AVS_HYSTERESIS = 0x2C,
|
||||
SAW3_SPM_STS2 = 0x38,
|
||||
SAW3_SPM_PMIC_DATA_3 = 0x4C,
|
||||
SAW3_VERSION = 0xFD0,
|
||||
};
|
||||
|
||||
/* Used for indexing into ctrl_reg. These are offets from 0x40 */
|
||||
enum spmi_common_control_register_index {
|
||||
SPMI_COMMON_IDX_VOLTAGE_RANGE = 0,
|
||||
|
@ -1035,6 +1054,89 @@ static irqreturn_t spmi_regulator_vs_ocp_isr(int irq, void *data)
|
|||
return IRQ_HANDLED;
|
||||
}
|
||||
|
||||
#define SAW3_VCTL_DATA_MASK 0xFF
|
||||
#define SAW3_VCTL_CLEAR_MASK 0x700FF
|
||||
#define SAW3_AVS_CTL_EN_MASK 0x1
|
||||
#define SAW3_AVS_CTL_TGGL_MASK 0x8000000
|
||||
#define SAW3_AVS_CTL_CLEAR_MASK 0x7efc00
|
||||
|
||||
static struct regmap *saw_regmap = NULL;
|
||||
|
||||
static void spmi_saw_set_vdd(void *data)
|
||||
{
|
||||
u32 vctl, data3, avs_ctl, pmic_sts;
|
||||
bool avs_enabled = false;
|
||||
unsigned long timeout;
|
||||
u8 voltage_sel = *(u8 *)data;
|
||||
|
||||
regmap_read(saw_regmap, SAW3_AVS_CTL, &avs_ctl);
|
||||
regmap_read(saw_regmap, SAW3_VCTL, &vctl);
|
||||
regmap_read(saw_regmap, SAW3_SPM_PMIC_DATA_3, &data3);
|
||||
|
||||
/* select the band */
|
||||
vctl &= ~SAW3_VCTL_CLEAR_MASK;
|
||||
vctl |= (u32)voltage_sel;
|
||||
|
||||
data3 &= ~SAW3_VCTL_CLEAR_MASK;
|
||||
data3 |= (u32)voltage_sel;
|
||||
|
||||
/* If AVS is enabled, switch it off during the voltage change */
|
||||
avs_enabled = SAW3_AVS_CTL_EN_MASK & avs_ctl;
|
||||
if (avs_enabled) {
|
||||
avs_ctl &= ~SAW3_AVS_CTL_TGGL_MASK;
|
||||
regmap_write(saw_regmap, SAW3_AVS_CTL, avs_ctl);
|
||||
}
|
||||
|
||||
regmap_write(saw_regmap, SAW3_RST, 1);
|
||||
regmap_write(saw_regmap, SAW3_VCTL, vctl);
|
||||
regmap_write(saw_regmap, SAW3_SPM_PMIC_DATA_3, data3);
|
||||
|
||||
timeout = jiffies + usecs_to_jiffies(100);
|
||||
do {
|
||||
regmap_read(saw_regmap, SAW3_PMIC_STS, &pmic_sts);
|
||||
pmic_sts &= SAW3_VCTL_DATA_MASK;
|
||||
if (pmic_sts == (u32)voltage_sel)
|
||||
break;
|
||||
|
||||
cpu_relax();
|
||||
|
||||
} while (time_before(jiffies, timeout));
|
||||
|
||||
/* After successful voltage change, switch the AVS back on */
|
||||
if (avs_enabled) {
|
||||
pmic_sts &= 0x3f;
|
||||
avs_ctl &= ~SAW3_AVS_CTL_CLEAR_MASK;
|
||||
avs_ctl |= ((pmic_sts - 4) << 10);
|
||||
avs_ctl |= (pmic_sts << 17);
|
||||
avs_ctl |= SAW3_AVS_CTL_TGGL_MASK;
|
||||
regmap_write(saw_regmap, SAW3_AVS_CTL, avs_ctl);
|
||||
}
|
||||
}
|
||||
|
||||
static int
|
||||
spmi_regulator_saw_set_voltage(struct regulator_dev *rdev, unsigned selector)
|
||||
{
|
||||
struct spmi_regulator *vreg = rdev_get_drvdata(rdev);
|
||||
int ret;
|
||||
u8 range_sel, voltage_sel;
|
||||
|
||||
ret = spmi_sw_selector_to_hw(vreg, selector, &range_sel, &voltage_sel);
|
||||
if (ret)
|
||||
return ret;
|
||||
|
||||
if (0 != range_sel) {
|
||||
dev_dbg(&rdev->dev, "range_sel = %02X voltage_sel = %02X", \
|
||||
range_sel, voltage_sel);
|
||||
return -EINVAL;
|
||||
}
|
||||
|
||||
/* Always do the SAW register writes on the first CPU */
|
||||
return smp_call_function_single(0, spmi_saw_set_vdd, \
|
||||
&voltage_sel, true);
|
||||
}
|
||||
|
||||
static struct regulator_ops spmi_saw_ops = {};
|
||||
|
||||
static struct regulator_ops spmi_smps_ops = {
|
||||
.enable = regulator_enable_regmap,
|
||||
.disable = regulator_disable_regmap,
|
||||
|
@ -1250,6 +1352,7 @@ static int spmi_regulator_match(struct spmi_regulator *vreg, u16 force_type)
|
|||
}
|
||||
dig_major_rev = version[SPMI_COMMON_REG_DIG_MAJOR_REV
|
||||
- SPMI_COMMON_REG_DIG_MAJOR_REV];
|
||||
|
||||
if (!force_type) {
|
||||
type = version[SPMI_COMMON_REG_TYPE -
|
||||
SPMI_COMMON_REG_DIG_MAJOR_REV];
|
||||
|
@ -1648,7 +1751,9 @@ static int qcom_spmi_regulator_probe(struct platform_device *pdev)
|
|||
struct regmap *regmap;
|
||||
const char *name;
|
||||
struct device *dev = &pdev->dev;
|
||||
int ret;
|
||||
struct device_node *node = pdev->dev.of_node;
|
||||
struct device_node *syscon;
|
||||
int ret, lenp;
|
||||
struct list_head *vreg_list;
|
||||
|
||||
vreg_list = devm_kzalloc(dev, sizeof(*vreg_list), GFP_KERNEL);
|
||||
|
@ -1665,7 +1770,22 @@ static int qcom_spmi_regulator_probe(struct platform_device *pdev)
|
|||
if (!match)
|
||||
return -ENODEV;
|
||||
|
||||
if (of_find_property(node, "qcom,saw-reg", &lenp)) {
|
||||
syscon = of_parse_phandle(node, "qcom,saw-reg", 0);
|
||||
saw_regmap = syscon_node_to_regmap(syscon);
|
||||
of_node_put(syscon);
|
||||
if (IS_ERR(regmap))
|
||||
dev_err(dev, "ERROR reading SAW regmap\n");
|
||||
}
|
||||
|
||||
for (reg = match->data; reg->name; reg++) {
|
||||
|
||||
if (saw_regmap && \
|
||||
of_find_property(of_find_node_by_name(node, reg->name), \
|
||||
"qcom,saw-slave", &lenp)) {
|
||||
continue;
|
||||
}
|
||||
|
||||
vreg = devm_kzalloc(dev, sizeof(*vreg), GFP_KERNEL);
|
||||
if (!vreg)
|
||||
return -ENOMEM;
|
||||
|
@ -1673,7 +1793,6 @@ static int qcom_spmi_regulator_probe(struct platform_device *pdev)
|
|||
vreg->dev = dev;
|
||||
vreg->base = reg->base;
|
||||
vreg->regmap = regmap;
|
||||
|
||||
if (reg->ocp) {
|
||||
vreg->ocp_irq = platform_get_irq_byname(pdev, reg->ocp);
|
||||
if (vreg->ocp_irq < 0) {
|
||||
|
@ -1681,7 +1800,6 @@ static int qcom_spmi_regulator_probe(struct platform_device *pdev)
|
|||
goto err;
|
||||
}
|
||||
}
|
||||
|
||||
vreg->desc.id = -1;
|
||||
vreg->desc.owner = THIS_MODULE;
|
||||
vreg->desc.type = REGULATOR_VOLTAGE;
|
||||
|
@ -1698,6 +1816,15 @@ static int qcom_spmi_regulator_probe(struct platform_device *pdev)
|
|||
if (ret)
|
||||
continue;
|
||||
|
||||
if (saw_regmap && \
|
||||
of_find_property(of_find_node_by_name(node, reg->name), \
|
||||
"qcom,saw-leader", &lenp)) {
|
||||
spmi_saw_ops = *(vreg->desc.ops);
|
||||
spmi_saw_ops.set_voltage_sel = \
|
||||
spmi_regulator_saw_set_voltage;
|
||||
vreg->desc.ops = &spmi_saw_ops;
|
||||
}
|
||||
|
||||
config.dev = dev;
|
||||
config.driver_data = vreg;
|
||||
config.regmap = regmap;
|
||||
|
|
Loading…
Reference in a new issue