[ALSA] adjust documentation for higher card limit
Modules: Documentation Fix all places in the docs where the card number limit is mentioned. Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
This commit is contained in:
parent
d001544ded
commit
0ef797c5ca
|
@ -105,7 +105,7 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
|
|||
Each of top level sound card module takes the following options.
|
||||
|
||||
index - index (slot #) of sound card
|
||||
- Values: 0 through 7 or negative
|
||||
- Values: 0 through 31 or negative
|
||||
- If nonnegative, assign that index number
|
||||
- if negative, interpret as a bitmask of permissible
|
||||
indices; the first free permitted index is assigned
|
||||
|
@ -134,7 +134,7 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
|
|||
dma2 - second DMA # for AD1816A chip (PnP setup)
|
||||
clockfreq - Clock frequency for AD1816A chip (default = 0, 33000Hz)
|
||||
|
||||
Module supports up to 8 cards, autoprobe and PnP.
|
||||
This module supports multiple cards, autoprobe and PnP.
|
||||
|
||||
Module snd-ad1848
|
||||
-----------------
|
||||
|
@ -145,7 +145,7 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
|
|||
irq - IRQ # for AD1848 chip
|
||||
dma1 - DMA # for AD1848 chip (0,1,3)
|
||||
|
||||
Module supports up to 8 cards. This module does not support autoprobe
|
||||
This module supports multiple cards. It does not support autoprobe
|
||||
thus main port must be specified!!! Other ports are optional.
|
||||
|
||||
The power-management is supported.
|
||||
|
@ -158,7 +158,7 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
|
|||
ac97_quirk - AC'97 workaround for strange hardware
|
||||
See the description of intel8x0 module for details.
|
||||
|
||||
This module supports up to 8 cards.
|
||||
This module supports multiple cards.
|
||||
|
||||
Module snd-ali5451
|
||||
------------------
|
||||
|
@ -186,7 +186,7 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
|
|||
mpu_irq - IRQ # for MPU-401 (PnP setup)
|
||||
fm_port - port # for OPL3 FM (PnP setup)
|
||||
|
||||
Module supports up to 8 cards, autoprobe and PnP.
|
||||
This module supports multiple cards, autoprobe and PnP.
|
||||
|
||||
The power-management is supported.
|
||||
|
||||
|
@ -198,7 +198,7 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
|
|||
joystick_port - port # for legacy joystick support.
|
||||
0 = disabled (default), 1 = auto-detect
|
||||
|
||||
Module supports up to 8 cards, autoprobe and PnP.
|
||||
This module supports multiple cards, autoprobe and PnP.
|
||||
|
||||
The power-management is supported.
|
||||
|
||||
|
@ -273,7 +273,7 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
|
|||
dma1 - 1st DMA # for AZT2320 (WSS) chip (PnP setup)
|
||||
dma2 - 2nd DMA # for AZT2320 (WSS) chip (PnP setup)
|
||||
|
||||
Module supports up to 8 cards, PnP and autoprobe.
|
||||
This module supports multiple cards, PnP and autoprobe.
|
||||
|
||||
The power-management is supported.
|
||||
|
||||
|
@ -284,7 +284,7 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
|
|||
|
||||
joystick - Enable joystick (default off)
|
||||
|
||||
Module supports up to 8 cards.
|
||||
This module supports multiple cards.
|
||||
|
||||
Module snd-bt87x
|
||||
----------------
|
||||
|
@ -294,7 +294,7 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
|
|||
digital_rate - Override the default digital rate (Hz)
|
||||
load_all - Load the driver even if the card model isn't known
|
||||
|
||||
Module supports up to 8 cards.
|
||||
This module supports multiple cards.
|
||||
|
||||
Note: The default index value of this module is -2, i.e. the first
|
||||
slot is excluded.
|
||||
|
@ -304,7 +304,7 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
|
|||
|
||||
Module for Creative Audigy LS and SB Live 24bit
|
||||
|
||||
Module supports up to 8 cards.
|
||||
This module supports multiple cards.
|
||||
|
||||
|
||||
Module snd-cmi8330
|
||||
|
@ -320,7 +320,7 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
|
|||
sbdma8 - 8bit DMA # for CMI8330 chip (SB16)
|
||||
sbdma16 - 16bit DMA # for CMI8330 chip (SB16)
|
||||
|
||||
Module supports up to 8 cards and autoprobe.
|
||||
This module supports multiple cards and autoprobe.
|
||||
|
||||
The power-management is supported.
|
||||
|
||||
|
@ -335,7 +335,7 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
|
|||
(default = 1)
|
||||
joystick_port - Joystick port address (0 = disable, 1 = auto-detect)
|
||||
|
||||
Module supports autoprobe and multiple chips (max 8).
|
||||
This module supports autoprobe and multiple cards.
|
||||
|
||||
The power-management is supported.
|
||||
|
||||
|
@ -351,7 +351,7 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
|
|||
dma1 - first DMA # for CS4231 chip
|
||||
dma2 - second DMA # for CS4231 chip
|
||||
|
||||
Module supports up to 8 cards. This module does not support autoprobe
|
||||
This module supports multiple cards. This module does not support autoprobe
|
||||
thus main port must be specified!!! Other ports are optional.
|
||||
|
||||
The power-management is supported.
|
||||
|
@ -371,7 +371,7 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
|
|||
dma2 - second DMA # for Yamaha CS4232 chip (0,1,3), -1 = disable
|
||||
isapnp - ISA PnP detection - 0 = disable, 1 = enable (default)
|
||||
|
||||
Module supports up to 8 cards. This module does not support autoprobe
|
||||
This module supports multiple cards. This module does not support autoprobe
|
||||
thus main port must be specified!!! Other ports are optional.
|
||||
|
||||
The power-management is supported.
|
||||
|
@ -392,7 +392,7 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
|
|||
dma2 - second DMA # for CS4236 chip (0,1,3), -1 = disable
|
||||
isapnp - ISA PnP detection - 0 = disable, 1 = enable (default)
|
||||
|
||||
Module supports up to 8 cards. This module does not support autoprobe
|
||||
This module supports multiple cards. This module does not support autoprobe
|
||||
(if ISA PnP is not used) thus main port and control port must be
|
||||
specified!!! Other ports are optional.
|
||||
|
||||
|
@ -405,7 +405,7 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
|
|||
|
||||
dual_codec - Secondary codec ID (0 = disable, default)
|
||||
|
||||
Module supports up to 8 cards.
|
||||
This module supports multiple cards.
|
||||
|
||||
The power-management is supported.
|
||||
|
||||
|
@ -419,7 +419,7 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
|
|||
thinkpad - Force to enable Thinkpad's CLKRUN control.
|
||||
mmap_valid - Support OSS mmap mode (default = 0).
|
||||
|
||||
Module supports up to 8 cards and autoprobe.
|
||||
This module supports multiple cards and autoprobe.
|
||||
Usually external amp and CLKRUN controls are detected automatically
|
||||
from PCI sub vendor/device ids. If they don't work, give the options
|
||||
above explicitly.
|
||||
|
@ -431,7 +431,7 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
|
|||
|
||||
Module for multifunction CS5535 companion PCI device
|
||||
|
||||
Module supports up to 8 cards.
|
||||
This module supports multiple cards.
|
||||
|
||||
Module snd-dt019x
|
||||
-----------------
|
||||
|
@ -446,7 +446,7 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
|
|||
mpu_irq - IRQ # for MPU-401 (PnP setup)
|
||||
dma8 - DMA # (PnP setup)
|
||||
|
||||
Module supports up to 8 cards. This module is enabled only with
|
||||
This module supports multiple cards. This module is enabled only with
|
||||
ISA PnP support.
|
||||
|
||||
The power-management is supported.
|
||||
|
@ -477,7 +477,7 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
|
|||
given in MB unit. Default value is 128.
|
||||
enable_ir - enable IR
|
||||
|
||||
Module supports up to 8 cards and autoprobe.
|
||||
This module supports multiple cards and autoprobe.
|
||||
|
||||
Input & Output configurations [extin/extout]
|
||||
* Creative Card wo/Digital out [0x0003/0x1f03]
|
||||
|
@ -500,7 +500,7 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
|
|||
|
||||
Module for Creative Emu10k1X (SB Live Dell OEM version)
|
||||
|
||||
Module supports up to 8 cards.
|
||||
This module supports multiple cards.
|
||||
|
||||
Module snd-ens1370
|
||||
------------------
|
||||
|
@ -511,7 +511,7 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
|
|||
|
||||
joystick - Enable joystick (default off)
|
||||
|
||||
Module supports up to 8 cards and autoprobe.
|
||||
This module supports multiple cards and autoprobe.
|
||||
|
||||
Module snd-ens1371
|
||||
------------------
|
||||
|
@ -524,7 +524,7 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
|
|||
joystick_port - port # for joystick (0x200,0x208,0x210,0x218),
|
||||
0 = disable (default), 1 = auto-detect
|
||||
|
||||
Module supports up to 8 cards and autoprobe.
|
||||
This module supports multiple cards and autoprobe.
|
||||
|
||||
Module snd-es968
|
||||
----------------
|
||||
|
@ -535,7 +535,7 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
|
|||
irq - IRQ # for ES968 (SB8) chip (PnP setup)
|
||||
dma1 - DMA # for ES968 (SB8) chip (PnP setup)
|
||||
|
||||
Module supports up to 8 cards, PnP and autoprobe.
|
||||
This module supports multiple cards, PnP and autoprobe.
|
||||
|
||||
The power-management is supported.
|
||||
|
||||
|
@ -550,7 +550,7 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
|
|||
mpu_irq - IRQ # for MPU-401 port (5,7,9,10)
|
||||
dma8 - DMA # for ES-1688 chip (0,1,3)
|
||||
|
||||
Module supports up to 8 cards and autoprobe (without MPU-401 port).
|
||||
This module supports multiple cards and autoprobe (without MPU-401 port).
|
||||
|
||||
Module snd-es18xx
|
||||
-----------------
|
||||
|
@ -565,8 +565,8 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
|
|||
dma2 - first DMA # for ES-18xx chip (0,1,3)
|
||||
isapnp - ISA PnP detection - 0 = disable, 1 = enable (default)
|
||||
|
||||
Module supports up to 8 cards ISA PnP and autoprobe (without MPU-401 port
|
||||
if native ISA PnP routines are not used).
|
||||
This module supports multiple cards, ISA PnP and autoprobe (without MPU-401
|
||||
port if native ISA PnP routines are not used).
|
||||
When dma2 is equal with dma1, the driver works as half-duplex.
|
||||
|
||||
The power-management is supported.
|
||||
|
@ -576,7 +576,7 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
|
|||
|
||||
Module for sound cards based on ESS Solo-1 (ES1938,ES1946) chips.
|
||||
|
||||
Module supports up to 8 cards and autoprobe.
|
||||
This module supports multiple cards and autoprobe.
|
||||
|
||||
The power-management is supported.
|
||||
|
||||
|
@ -594,7 +594,7 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
|
|||
enable_mpu - enable MPU401 (0 = off, 1 = on, 2 = auto (default))
|
||||
joystick - enable joystick (default off)
|
||||
|
||||
Module supports up to 8 cards and autoprobe.
|
||||
This module supports multiple cards and autoprobe.
|
||||
|
||||
The power-management is supported.
|
||||
|
||||
|
@ -610,7 +610,7 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
|
|||
- High 16-bits are video (radio) device number + 1
|
||||
- example: 0x10002 (MediaForte 256-PCPR, device 1)
|
||||
|
||||
Module supports up to 8 cards and autoprobe.
|
||||
This module supports multiple cards and autoprobe.
|
||||
|
||||
The power-management is supported.
|
||||
|
||||
|
@ -627,7 +627,7 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
|
|||
voices - GF1 voices limit (14-32)
|
||||
pcm_voices - reserved PCM voices
|
||||
|
||||
Module supports up to 8 cards and autoprobe.
|
||||
This module supports multiple cards and autoprobe.
|
||||
|
||||
Module snd-gusextreme
|
||||
---------------------
|
||||
|
@ -646,7 +646,7 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
|
|||
voices - GF1 voices limit (14-32)
|
||||
pcm_voices - reserved PCM voices
|
||||
|
||||
Module supports up to 8 cards and autoprobe (without MPU-401 port).
|
||||
This module supports multiple cards and autoprobe (without MPU-401 port).
|
||||
|
||||
Module snd-gusmax
|
||||
-----------------
|
||||
|
@ -661,7 +661,7 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
|
|||
voices - GF1 voices limit (14-32)
|
||||
pcm_voices - reserved PCM voices
|
||||
|
||||
Module supports up to 8 cards and autoprobe.
|
||||
This module supports multiple cards and autoprobe.
|
||||
|
||||
Module snd-hda-intel
|
||||
--------------------
|
||||
|
@ -730,7 +730,7 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
|
|||
|
||||
Module for RME Hammerfall DSP audio interface(s)
|
||||
|
||||
Module supports up to 8 cards.
|
||||
This module supports multiple cards.
|
||||
|
||||
Note: The firmware data can be automatically loaded via hotplug
|
||||
when CONFIG_FW_LOADER is set. Otherwise, you need to load
|
||||
|
@ -788,7 +788,7 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
|
|||
cs8427_timeout - reset timeout for the CS8427 chip (S/PDIF transciever)
|
||||
in msec resolution, default value is 500 (0.5 sec)
|
||||
|
||||
Module supports up to 8 cards and autoprobe. Note: The consumer part
|
||||
This module supports multiple cards and autoprobe. Note: The consumer part
|
||||
is not used with all Envy24 based cards (for example in the MidiMan Delta
|
||||
serie).
|
||||
|
||||
|
@ -824,7 +824,7 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
|
|||
aureon71, universe, k8x800, phase22, phase28, ms300,
|
||||
av710
|
||||
|
||||
Module supports up to 8 cards and autoprobe.
|
||||
This module supports multiple cards and autoprobe.
|
||||
|
||||
Note: The supported board is detected by reading EEPROM or PCI
|
||||
SSID (if EEPROM isn't available). You can override the
|
||||
|
@ -894,7 +894,7 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
|
|||
effect - 1 = InterWave effects enable (default 0);
|
||||
requires 8 voices
|
||||
|
||||
Module supports up to 8 cards, autoprobe and ISA PnP.
|
||||
This module supports multiple cards, autoprobe and ISA PnP.
|
||||
|
||||
Module snd-interwave-stb
|
||||
------------------------
|
||||
|
@ -914,14 +914,14 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
|
|||
effect - 1 = InterWave effects enable (default 0);
|
||||
requires 8 voices
|
||||
|
||||
Module supports up to 8 cards, autoprobe and ISA PnP.
|
||||
This module supports multiple cards, autoprobe and ISA PnP.
|
||||
|
||||
Module snd-korg1212
|
||||
-------------------
|
||||
|
||||
Module for Korg 1212 IO PCI card
|
||||
|
||||
Module supports up to 8 cards.
|
||||
This module supports multiple cards.
|
||||
|
||||
Module snd-maestro3
|
||||
-------------------
|
||||
|
@ -933,7 +933,7 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
|
|||
-1 for default pin (8 for allegro, 1 for
|
||||
others)
|
||||
|
||||
Module supports autoprobe and multiple chips (max 8).
|
||||
This module supports autoprobe and multiple chips.
|
||||
|
||||
Note: the binding of amplifier is dependent on hardware.
|
||||
If there is no sound even though all channels are unmuted, try to
|
||||
|
@ -948,7 +948,7 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
|
|||
|
||||
Module for Digigram miXart8 sound cards.
|
||||
|
||||
Module supports multiple cards.
|
||||
This module supports multiple cards.
|
||||
Note: One miXart8 board will be represented as 4 alsa cards.
|
||||
See MIXART.txt for details.
|
||||
|
||||
|
@ -967,7 +967,7 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
|
|||
irq - IRQ number or -1 (disable)
|
||||
pnp - PnP detection - 0 = disable, 1 = enable (default)
|
||||
|
||||
Module supports multiple devices (max 8) and PnP.
|
||||
This module supports multiple devices and PnP.
|
||||
|
||||
Module snd-mtpav
|
||||
----------------
|
||||
|
@ -1053,7 +1053,7 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
|
|||
dma2 - second DMA # for Yamaha OPL3-SA chip (0,1,3), -1 = disable
|
||||
isapnp - ISA PnP detection - 0 = disable, 1 = enable (default)
|
||||
|
||||
Module supports up to 8 cards and ISA PnP. This module does not support
|
||||
This module supports multiple cards and ISA PnP. It does not support
|
||||
autoprobe (if ISA PnP is not used) thus all ports must be specified!!!
|
||||
|
||||
The power-management is supported.
|
||||
|
@ -1131,14 +1131,14 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
|
|||
Module for RME Digi32, Digi32 Pro and Digi32/8 (Sek'd Prodif32,
|
||||
Prodif96 and Prodif Gold) sound cards.
|
||||
|
||||
Module supports up to 8 cards.
|
||||
This module supports multiple cards.
|
||||
|
||||
Module snd-rme96
|
||||
----------------
|
||||
|
||||
Module for RME Digi96, Digi96/8 and Digi96/8 PRO/PAD/PST sound cards.
|
||||
|
||||
Module supports up to 8 cards.
|
||||
This module supports multiple cards.
|
||||
|
||||
Module snd-rme9652
|
||||
------------------
|
||||
|
@ -1148,7 +1148,7 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
|
|||
precise_ptr - Enable precise pointer (doesn't work reliably).
|
||||
(default = 0)
|
||||
|
||||
Module supports up to 8 cards.
|
||||
This module supports multiple cards.
|
||||
|
||||
Note: snd-page-alloc module does the job which snd-hammerfall-mem
|
||||
module did formerly. It will allocate the buffers in advance
|
||||
|
@ -1178,7 +1178,7 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
|
|||
irq - IRQ # for SB DSP chip (5,7,9,10)
|
||||
dma8 - DMA # for SB DSP chip (1,3)
|
||||
|
||||
Module supports up to 8 cards and autoprobe.
|
||||
This module supports multiple cards and autoprobe.
|
||||
|
||||
The power-management is supported.
|
||||
|
||||
|
@ -1200,7 +1200,7 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
|
|||
csp - ASP/CSP chip support - 0 = disable (default), 1 = enable
|
||||
isapnp - ISA PnP detection - 0 = disable, 1 = enable (default)
|
||||
|
||||
Module supports up to 8 cards, autoprobe and ISA PnP.
|
||||
This module supports multiple cards, autoprobe and ISA PnP.
|
||||
|
||||
Note: To use Vibra16X cards in 16-bit half duplex mode, you must
|
||||
disable 16bit DMA with dma16 = -1 module parameter.
|
||||
|
@ -1220,7 +1220,7 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
|
|||
irq - IRQ # (7,9,10,11)
|
||||
dma1 - DMA #
|
||||
|
||||
Module supports up to 8 cards.
|
||||
This module supports multiple cards.
|
||||
|
||||
The power-management is supported.
|
||||
|
||||
|
@ -1234,7 +1234,7 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
|
|||
mpu_irq - MPU-401 IRQ # (PnP setup)
|
||||
dma - DMA # (PnP setup)
|
||||
|
||||
Module supports up to 8 cards. ISA PnP must be enabled.
|
||||
This module supports multiple cards. ISA PnP must be enabled.
|
||||
You need sscape_ctl tool in alsa-tools package for loading
|
||||
the microcode.
|
||||
|
||||
|
@ -1243,21 +1243,21 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
|
|||
|
||||
Module for AMD7930 sound chips found on Sparcs.
|
||||
|
||||
Module supports up to 8 cards.
|
||||
This module supports multiple cards.
|
||||
|
||||
Module snd-sun-cs4231 (on sparc only)
|
||||
-------------------------------------
|
||||
|
||||
Module for CS4231 sound chips found on Sparcs.
|
||||
|
||||
Module supports up to 8 cards.
|
||||
This module supports multiple cards.
|
||||
|
||||
Module snd-sun-dbri (on sparc only)
|
||||
-----------------------------------
|
||||
|
||||
Module for DBRI sound chips found on Sparcs.
|
||||
|
||||
Module supports up to 8 cards.
|
||||
This module supports multiple cards.
|
||||
|
||||
Module snd-wavefront
|
||||
--------------------
|
||||
|
@ -1277,7 +1277,7 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
|
|||
dma2 - DMA2 # for CS4232 PCM interface.
|
||||
isapnp - ISA PnP detection - 0 = disable, 1 = enable (default)
|
||||
|
||||
Module supports up to 8 cards and ISA PnP.
|
||||
This module supports multiple cards and ISA PnP.
|
||||
|
||||
Module snd-sonicvibes
|
||||
---------------------
|
||||
|
@ -1289,7 +1289,7 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
|
|||
- SoundCard must have onboard SRAM for this.
|
||||
mge - Mic Gain Enable - 1 = enable, 0 = disable (default)
|
||||
|
||||
Module supports up to 8 cards and autoprobe.
|
||||
This module supports multiple cards and autoprobe.
|
||||
|
||||
Module snd-serial-u16550
|
||||
------------------------
|
||||
|
@ -1308,7 +1308,7 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
|
|||
0 = Soundcanvas, 1 = MS-124T, 2 = MS-124W S/A,
|
||||
3 = MS-124W M/B, 4 = Generic
|
||||
|
||||
Module supports up to 8 cards. This module does not support autoprobe
|
||||
This module supports multiple cards. This module does not support autoprobe
|
||||
thus the main port must be specified!!! Other options are optional.
|
||||
|
||||
Module snd-trident
|
||||
|
@ -1327,7 +1327,7 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
|
|||
pcm_channels - max channels (voices) reserved for PCM
|
||||
wavetable_size - max wavetable size in kB (4-?kb)
|
||||
|
||||
Module supports up to 8 cards and autoprobe.
|
||||
This module supports multiple cards and autoprobe.
|
||||
|
||||
The power-management is supported.
|
||||
|
||||
|
@ -1339,14 +1339,14 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
|
|||
vid - Vendor ID for the device (optional)
|
||||
pid - Product ID for the device (optional)
|
||||
|
||||
This module supports up to 8 cards, autoprobe and hotplugging.
|
||||
This module supports multiple devices, autoprobe and hotplugging.
|
||||
|
||||
Module snd-usb-usx2y
|
||||
--------------------
|
||||
|
||||
Module for Tascam USB US-122, US-224 and US-428 devices.
|
||||
|
||||
This module supports up to 8 cards, autoprobe and hotplugging.
|
||||
This module supports multiple devices, autoprobe and hotplugging.
|
||||
|
||||
Note: you need to load the firmware via usx2yloader utility included
|
||||
in alsa-tools and alsa-firmware packages.
|
||||
|
@ -1428,9 +1428,9 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
|
|||
This module creates virtual rawmidi devices which communicate
|
||||
to the corresponding ALSA sequencer ports.
|
||||
|
||||
midi_devs - MIDI devices # (1-8, default=4)
|
||||
midi_devs - MIDI devices # (1-4, default=4)
|
||||
|
||||
Module supports up to 8 cards.
|
||||
This module supports multiple cards.
|
||||
|
||||
Module snd-vx222
|
||||
----------------
|
||||
|
@ -1440,7 +1440,7 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
|
|||
mic - Enable Microphone on V222 Mic (NYI)
|
||||
ibl - Capture IBL size. (default = 0, minimum size)
|
||||
|
||||
Module supports up to 8 cards.
|
||||
This module supports multiple cards.
|
||||
|
||||
When the driver is compiled as a module and the hotplug firmware
|
||||
is supported, the firmware data is loaded via hotplug automatically.
|
||||
|
@ -1468,7 +1468,7 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
|
|||
|
||||
ibl - Capture IBL size. (default = 0, minimum size)
|
||||
|
||||
Module supports up to 8 cards. The module is compiled only when
|
||||
This module supports multiple cards. The module is compiled only when
|
||||
PCMCIA is supported on kernel.
|
||||
|
||||
With the older 2.6.x kernel, to activate the driver via the card
|
||||
|
@ -1504,7 +1504,7 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
|
|||
1 (auto-detect)
|
||||
rear_switch - enable shared rear/line-in switch (bool)
|
||||
|
||||
Module supports autoprobe and multiple chips (max 8).
|
||||
This module supports autoprobe and multiple chips.
|
||||
|
||||
The power-management is supported.
|
||||
|
||||
|
|
Loading…
Reference in a new issue