diff --git a/arch/ppc/Kconfig b/arch/ppc/Kconfig index be4e629e69d0..a862c037c65d 100644 --- a/arch/ppc/Kconfig +++ b/arch/ppc/Kconfig @@ -878,6 +878,13 @@ config MPC10X_STORE_GATHERING bool "Enable MPC10x store gathering" depends on MPC10X_BRIDGE +config SANDPOINT_ENABLE_UART1 + bool "Enable DUART mode on Sandpoint" + depends on SANDPOINT + help + If this option is enabled then the MPC824x processor will run + in DUART mode instead of UART mode. + config CPC710_DATA_GATHERING bool "Enable CPC710 data gathering" depends on K2 diff --git a/arch/ppc/configs/sandpoint_defconfig b/arch/ppc/configs/sandpoint_defconfig index 0f4393a07f82..fb493a67c60d 100644 --- a/arch/ppc/configs/sandpoint_defconfig +++ b/arch/ppc/configs/sandpoint_defconfig @@ -437,7 +437,7 @@ CONFIG_SOUND_GAMEPORT=y # CONFIG_SERIAL_8250=y CONFIG_SERIAL_8250_CONSOLE=y -CONFIG_SERIAL_8250_NR_UARTS=2 +CONFIG_SERIAL_8250_NR_UARTS=4 # CONFIG_SERIAL_8250_EXTENDED is not set # diff --git a/arch/ppc/platforms/sandpoint.c b/arch/ppc/platforms/sandpoint.c index 8b149c2fc54f..21e31346b12b 100644 --- a/arch/ppc/platforms/sandpoint.c +++ b/arch/ppc/platforms/sandpoint.c @@ -311,19 +311,22 @@ sandpoint_setup_arch(void) { bd_t *bp = (bd_t *)__res; struct plat_serial8250_port *pdata; - pdata = (struct plat_serial8250_port *) ppc_sys_get_pdata(MPC10X_DUART); + pdata = (struct plat_serial8250_port *) ppc_sys_get_pdata(MPC10X_UART0); if (pdata) { pdata[0].uartclk = bp->bi_busfreq; - pdata[0].membase = ioremap(pdata[0].mapbase, 0x100); - - /* this disables the 2nd serial port on the DUART - * since the sandpoint does not have it connected */ - pdata[1].uartclk = 0; - pdata[1].irq = 0; - pdata[1].mapbase = 0; } + +#ifdef CONFIG_SANDPOINT_ENABLE_UART1 + pdata = (struct plat_serial8250_port *) ppc_sys_get_pdata(MPC10X_UART1); + if (pdata) + { + pdata[0].uartclk = bp->bi_busfreq; + } +#else + ppc_sys_device_remove(MPC10X_UART1); +#endif } printk(KERN_INFO "Motorola SPS Sandpoint Test Platform\n"); diff --git a/arch/ppc/syslib/mpc10x_common.c b/arch/ppc/syslib/mpc10x_common.c index 8fc5f4154521..87065e2e4c5f 100644 --- a/arch/ppc/syslib/mpc10x_common.c +++ b/arch/ppc/syslib/mpc10x_common.c @@ -45,24 +45,29 @@ #define MPC10X_DMA0_IRQ (EPIC_IRQ_BASE + 1 + NUM_8259_INTERRUPTS) #define MPC10X_DMA1_IRQ (EPIC_IRQ_BASE + 2 + NUM_8259_INTERRUPTS) #define MPC10X_UART0_IRQ (EPIC_IRQ_BASE + 4 + NUM_8259_INTERRUPTS) +#define MPC10X_UART1_IRQ (EPIC_IRQ_BASE + 5 + NUM_8259_INTERRUPTS) #else #define MPC10X_I2C_IRQ -1 #define MPC10X_DMA0_IRQ -1 #define MPC10X_DMA1_IRQ -1 #define MPC10X_UART0_IRQ -1 +#define MPC10X_UART1_IRQ -1 #endif static struct fsl_i2c_platform_data mpc10x_i2c_pdata = { .device_flags = 0, }; -static struct plat_serial8250_port serial_platform_data[] = { +static struct plat_serial8250_port serial_plat_uart0[] = { [0] = { .mapbase = 0x4500, .iotype = UPIO_MEM, .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, }, - [1] = { + { }, +}; +static struct plat_serial8250_port serial_plat_uart1[] = { + [0] = { .mapbase = 0x4600, .iotype = UPIO_MEM, .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, @@ -133,11 +138,17 @@ struct platform_device ppc_sys_platform_devices[] = { }, }, }, - [MPC10X_DUART] = { + [MPC10X_UART0] = { .name = "serial8250", .id = 0, - .dev.platform_data = serial_platform_data, + .dev.platform_data = serial_plat_uart0, }, + [MPC10X_UART1] = { + .name = "serial8250", + .id = 1, + .dev.platform_data = serial_plat_uart1, + }, + }; /* We use the PCI ID to match on */ @@ -147,10 +158,10 @@ struct ppc_sys_spec ppc_sys_specs[] = { .ppc_sys_name = "8245", .mask = 0xFFFFFFFF, .value = MPC10X_BRIDGE_8245, - .num_devices = 4, + .num_devices = 5, .device_list = (enum ppc_sys_devices[]) { - MPC10X_IIC1, MPC10X_DMA0, MPC10X_DMA1, MPC10X_DUART, + MPC10X_IIC1, MPC10X_DMA0, MPC10X_DMA1, MPC10X_UART0, MPC10X_UART1, }, }, { @@ -180,6 +191,25 @@ struct ppc_sys_spec ppc_sys_specs[] = { }, }; +/* + * mach_mpc10x_fixup: This function enables DUART mode if it detects + * if it detects two UARTS in the platform device entries. + */ +static int __init mach_mpc10x_fixup(struct platform_device *pdev) +{ + if (strncmp (pdev->name, "serial8250", 10) == 0 && pdev->id == 1) + writeb(readb(serial_plat_uart1[0].membase + 0x11) | 0x1, + serial_plat_uart1[0].membase + 0x11); + return 0; +} + +static int __init mach_mpc10x_init(void) +{ + ppc_sys_device_fixup = mach_mpc10x_fixup; + return 0; +} +postcore_initcall(mach_mpc10x_init); + /* Set resources to match bridge memory map */ void __init mpc10x_bridge_set_resources(int map, struct pci_controller *hose) @@ -219,6 +249,7 @@ mpc10x_bridge_set_resources(int map, struct pci_controller *hose) ppc_md.progress("mpc10x:exit1", 0x100); } } + /* * Do some initialization and put the EUMB registers at the specified address * (also map the EPIC registers into virtual space--OpenPIC_Addr will be set). @@ -411,11 +442,13 @@ mpc10x_bridge_init(struct pci_controller *hose, ppc_sys_platform_devices[MPC10X_DMA1].resource[1].start = MPC10X_DMA1_IRQ; ppc_sys_platform_devices[MPC10X_DMA1].resource[1].end = MPC10X_DMA1_IRQ; - serial_platform_data[0].mapbase += phys_eumb_base; - serial_platform_data[0].irq = MPC10X_UART0_IRQ; + serial_plat_uart0[0].mapbase += phys_eumb_base; + serial_plat_uart0[0].irq = MPC10X_UART0_IRQ; + serial_plat_uart0[0].membase = ioremap(serial_plat_uart0[0].mapbase, 0x100); - serial_platform_data[1].mapbase += phys_eumb_base; - serial_platform_data[1].irq = MPC10X_UART0_IRQ + 1; + serial_plat_uart1[0].mapbase += phys_eumb_base; + serial_plat_uart1[0].irq = MPC10X_UART1_IRQ; + serial_plat_uart1[0].membase = ioremap(serial_plat_uart1[0].mapbase, 0x100); /* * 8240 erratum 26, 8241/8245 erratum 29, 107 erratum 23: speculative diff --git a/include/asm-ppc/mpc10x.h b/include/asm-ppc/mpc10x.h index f5196a4efbe0..77b1e092c206 100644 --- a/include/asm-ppc/mpc10x.h +++ b/include/asm-ppc/mpc10x.h @@ -163,7 +163,8 @@ enum ppc_sys_devices { MPC10X_IIC1, MPC10X_DMA0, MPC10X_DMA1, - MPC10X_DUART, + MPC10X_UART0, + MPC10X_UART1, }; int mpc10x_bridge_init(struct pci_controller *hose,