Merge branch 'devicetree/merge' of git://git.secretlab.ca/git/linux-2.6
* 'devicetree/merge' of git://git.secretlab.ca/git/linux-2.6: Revert "dt: add documentation of ARM dt boot interface"
This commit is contained in:
commit
15a831f253
|
@ -65,19 +65,13 @@ looks at the connected hardware is beyond the scope of this document.
|
|||
The boot loader must ultimately be able to provide a MACH_TYPE_xxx
|
||||
value to the kernel. (see linux/arch/arm/tools/mach-types).
|
||||
|
||||
4. Setup boot data
|
||||
------------------
|
||||
|
||||
4. Setup the kernel tagged list
|
||||
-------------------------------
|
||||
|
||||
Existing boot loaders: OPTIONAL, HIGHLY RECOMMENDED
|
||||
New boot loaders: MANDATORY
|
||||
|
||||
The boot loader must provide either a tagged list or a dtb image for
|
||||
passing configuration data to the kernel. The physical address of the
|
||||
boot data is passed to the kernel in register r2.
|
||||
|
||||
4a. Setup the kernel tagged list
|
||||
--------------------------------
|
||||
|
||||
The boot loader must create and initialise the kernel tagged list.
|
||||
A valid tagged list starts with ATAG_CORE and ends with ATAG_NONE.
|
||||
The ATAG_CORE tag may or may not be empty. An empty ATAG_CORE tag
|
||||
|
@ -107,24 +101,6 @@ The tagged list must be placed in a region of memory where neither
|
|||
the kernel decompressor nor initrd 'bootp' program will overwrite
|
||||
it. The recommended placement is in the first 16KiB of RAM.
|
||||
|
||||
4b. Setup the device tree
|
||||
-------------------------
|
||||
|
||||
The boot loader must load a device tree image (dtb) into system ram
|
||||
at a 64bit aligned address and initialize it with the boot data. The
|
||||
dtb format is documented in Documentation/devicetree/booting-without-of.txt.
|
||||
The kernel will look for the dtb magic value of 0xd00dfeed at the dtb
|
||||
physical address to determine if a dtb has been passed instead of a
|
||||
tagged list.
|
||||
|
||||
The boot loader must pass at a minimum the size and location of the
|
||||
system memory, and the root filesystem location. The dtb must be
|
||||
placed in a region of memory where the kernel decompressor will not
|
||||
overwrite it. The recommended placement is in the first 16KiB of RAM
|
||||
with the caveat that it may not be located at physical address 0 since
|
||||
the kernel interprets a value of 0 in r2 to mean neither a tagged list
|
||||
nor a dtb were passed.
|
||||
|
||||
5. Calling the kernel image
|
||||
---------------------------
|
||||
|
||||
|
@ -149,8 +125,7 @@ In either case, the following conditions must be met:
|
|||
- CPU register settings
|
||||
r0 = 0,
|
||||
r1 = machine type number discovered in (3) above.
|
||||
r2 = physical address of tagged list in system RAM, or
|
||||
physical address of device tree block (dtb) in system RAM
|
||||
r2 = physical address of tagged list in system RAM.
|
||||
|
||||
- CPU mode
|
||||
All forms of interrupts must be disabled (IRQs and FIQs)
|
||||
|
|
|
@ -13,7 +13,6 @@ Table of Contents
|
|||
|
||||
I - Introduction
|
||||
1) Entry point for arch/powerpc
|
||||
2) Entry point for arch/arm
|
||||
|
||||
II - The DT block format
|
||||
1) Header
|
||||
|
@ -226,45 +225,6 @@ it with special cases.
|
|||
cannot support both configurations with Book E and configurations
|
||||
with classic Powerpc architectures.
|
||||
|
||||
2) Entry point for arch/arm
|
||||
---------------------------
|
||||
|
||||
There is one single entry point to the kernel, at the start
|
||||
of the kernel image. That entry point supports two calling
|
||||
conventions. A summary of the interface is described here. A full
|
||||
description of the boot requirements is documented in
|
||||
Documentation/arm/Booting
|
||||
|
||||
a) ATAGS interface. Minimal information is passed from firmware
|
||||
to the kernel with a tagged list of predefined parameters.
|
||||
|
||||
r0 : 0
|
||||
|
||||
r1 : Machine type number
|
||||
|
||||
r2 : Physical address of tagged list in system RAM
|
||||
|
||||
b) Entry with a flattened device-tree block. Firmware loads the
|
||||
physical address of the flattened device tree block (dtb) into r2,
|
||||
r1 is not used, but it is considered good practise to use a valid
|
||||
machine number as described in Documentation/arm/Booting.
|
||||
|
||||
r0 : 0
|
||||
|
||||
r1 : Valid machine type number. When using a device tree,
|
||||
a single machine type number will often be assigned to
|
||||
represent a class or family of SoCs.
|
||||
|
||||
r2 : physical pointer to the device-tree block
|
||||
(defined in chapter II) in RAM. Device tree can be located
|
||||
anywhere in system RAM, but it should be aligned on a 32 bit
|
||||
boundary.
|
||||
|
||||
The kernel will differentiate between ATAGS and device tree booting by
|
||||
reading the memory pointed to by r1 and looking for either the flattened
|
||||
device tree block magic value (0xd00dfeed) or the ATAG_CORE value at
|
||||
offset 0x4 from r2 (0x54410001).
|
||||
|
||||
|
||||
II - The DT block format
|
||||
========================
|
||||
|
|
Loading…
Reference in a new issue