smsc911x: add dynamic bus configuration
Convert the driver to select 16-bit or 32-bit bus access at runtime, at a small performance cost. Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com> Acked-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This commit is contained in:
parent
6fabd715e6
commit
2107fb8b5b
|
@ -77,19 +77,16 @@ struct smsc911x_data {
|
|||
unsigned int generation;
|
||||
|
||||
/* device configuration (copied from platform_data during probe) */
|
||||
unsigned int irq_polarity;
|
||||
unsigned int irq_type;
|
||||
phy_interface_t phy_interface;
|
||||
struct smsc911x_platform_config config;
|
||||
|
||||
/* This needs to be acquired before calling any of below:
|
||||
* smsc911x_mac_read(), smsc911x_mac_write()
|
||||
*/
|
||||
spinlock_t mac_lock;
|
||||
|
||||
#if (!SMSC_CAN_USE_32BIT)
|
||||
/* spinlock to ensure 16-bit accesses are serialised */
|
||||
/* spinlock to ensure 16-bit accesses are serialised.
|
||||
* unused with a 32-bit bus */
|
||||
spinlock_t dev_lock;
|
||||
#endif
|
||||
|
||||
struct phy_device *phy_dev;
|
||||
struct mii_bus *mii_bus;
|
||||
|
@ -121,70 +118,56 @@ struct smsc911x_data {
|
|||
unsigned int hashlo;
|
||||
};
|
||||
|
||||
#if SMSC_CAN_USE_32BIT
|
||||
|
||||
static inline u32 smsc911x_reg_read(struct smsc911x_data *pdata, u32 reg)
|
||||
{
|
||||
return readl(pdata->ioaddr + reg);
|
||||
}
|
||||
|
||||
static inline void smsc911x_reg_write(struct smsc911x_data *pdata, u32 reg,
|
||||
u32 val)
|
||||
{
|
||||
writel(val, pdata->ioaddr + reg);
|
||||
}
|
||||
|
||||
/* Writes a packet to the TX_DATA_FIFO */
|
||||
static inline void
|
||||
smsc911x_tx_writefifo(struct smsc911x_data *pdata, unsigned int *buf,
|
||||
unsigned int wordcount)
|
||||
{
|
||||
writesl(pdata->ioaddr + TX_DATA_FIFO, buf, wordcount);
|
||||
}
|
||||
|
||||
/* Reads a packet out of the RX_DATA_FIFO */
|
||||
static inline void
|
||||
smsc911x_rx_readfifo(struct smsc911x_data *pdata, unsigned int *buf,
|
||||
unsigned int wordcount)
|
||||
{
|
||||
readsl(pdata->ioaddr + RX_DATA_FIFO, buf, wordcount);
|
||||
}
|
||||
|
||||
#else /* SMSC_CAN_USE_32BIT */
|
||||
|
||||
/* These 16-bit access functions are significantly slower, due to the locking
|
||||
/* The 16-bit access functions are significantly slower, due to the locking
|
||||
* necessary. If your bus hardware can be configured to do this for you
|
||||
* (in response to a single 32-bit operation from software), you should use
|
||||
* the 32-bit access functions instead. */
|
||||
|
||||
static inline u32 smsc911x_reg_read(struct smsc911x_data *pdata, u32 reg)
|
||||
{
|
||||
unsigned long flags;
|
||||
u32 data;
|
||||
if (pdata->config.flags & SMSC911X_USE_32BIT)
|
||||
return readl(pdata->ioaddr + reg);
|
||||
|
||||
/* these two 16-bit reads must be performed consecutively, so must
|
||||
* not be interrupted by our own ISR (which would start another
|
||||
* read operation) */
|
||||
if (pdata->config.flags & SMSC911X_USE_16BIT) {
|
||||
u32 data;
|
||||
unsigned long flags;
|
||||
|
||||
/* these two 16-bit reads must be performed consecutively, so
|
||||
* must not be interrupted by our own ISR (which would start
|
||||
* another read operation) */
|
||||
spin_lock_irqsave(&pdata->dev_lock, flags);
|
||||
data = ((readw(pdata->ioaddr + reg) & 0xFFFF) |
|
||||
((readw(pdata->ioaddr + reg + 2) & 0xFFFF) << 16));
|
||||
spin_unlock_irqrestore(&pdata->dev_lock, flags);
|
||||
|
||||
return data;
|
||||
}
|
||||
|
||||
BUG();
|
||||
}
|
||||
|
||||
static inline void smsc911x_reg_write(struct smsc911x_data *pdata, u32 reg,
|
||||
u32 val)
|
||||
{
|
||||
if (pdata->config.flags & SMSC911X_USE_32BIT) {
|
||||
writel(val, pdata->ioaddr + reg);
|
||||
return;
|
||||
}
|
||||
|
||||
if (pdata->config.flags & SMSC911X_USE_16BIT) {
|
||||
unsigned long flags;
|
||||
|
||||
/* these two 16-bit writes must be performed consecutively, so must
|
||||
* not be interrupted by our own ISR (which would start another
|
||||
* read operation) */
|
||||
/* these two 16-bit writes must be performed consecutively, so
|
||||
* must not be interrupted by our own ISR (which would start
|
||||
* another read operation) */
|
||||
spin_lock_irqsave(&pdata->dev_lock, flags);
|
||||
writew(val & 0xFFFF, pdata->ioaddr + reg);
|
||||
writew((val >> 16) & 0xFFFF, pdata->ioaddr + reg + 2);
|
||||
spin_unlock_irqrestore(&pdata->dev_lock, flags);
|
||||
return;
|
||||
}
|
||||
|
||||
BUG();
|
||||
}
|
||||
|
||||
/* Writes a packet to the TX_DATA_FIFO */
|
||||
|
@ -192,8 +175,18 @@ static inline void
|
|||
smsc911x_tx_writefifo(struct smsc911x_data *pdata, unsigned int *buf,
|
||||
unsigned int wordcount)
|
||||
{
|
||||
if (pdata->config.flags & SMSC911X_USE_32BIT) {
|
||||
writesl(pdata->ioaddr + TX_DATA_FIFO, buf, wordcount);
|
||||
return;
|
||||
}
|
||||
|
||||
if (pdata->config.flags & SMSC911X_USE_16BIT) {
|
||||
while (wordcount--)
|
||||
smsc911x_reg_write(pdata, TX_DATA_FIFO, *buf++);
|
||||
return;
|
||||
}
|
||||
|
||||
BUG();
|
||||
}
|
||||
|
||||
/* Reads a packet out of the RX_DATA_FIFO */
|
||||
|
@ -201,11 +194,19 @@ static inline void
|
|||
smsc911x_rx_readfifo(struct smsc911x_data *pdata, unsigned int *buf,
|
||||
unsigned int wordcount)
|
||||
{
|
||||
if (pdata->config.flags & SMSC911X_USE_32BIT) {
|
||||
readsl(pdata->ioaddr + RX_DATA_FIFO, buf, wordcount);
|
||||
return;
|
||||
}
|
||||
|
||||
if (pdata->config.flags & SMSC911X_USE_16BIT) {
|
||||
while (wordcount--)
|
||||
*buf++ = smsc911x_reg_read(pdata, RX_DATA_FIFO);
|
||||
}
|
||||
return;
|
||||
}
|
||||
|
||||
#endif /* SMSC_CAN_USE_32BIT */
|
||||
BUG();
|
||||
}
|
||||
|
||||
/* waits for MAC not busy, with timeout. Only called by smsc911x_mac_read
|
||||
* and smsc911x_mac_write, so assumes mac_lock is held */
|
||||
|
@ -790,7 +791,7 @@ static int smsc911x_mii_probe(struct net_device *dev)
|
|||
}
|
||||
|
||||
phydev = phy_connect(dev, phydev->dev.bus_id,
|
||||
&smsc911x_phy_adjust_link, 0, pdata->phy_interface);
|
||||
&smsc911x_phy_adjust_link, 0, pdata->config.phy_interface);
|
||||
|
||||
if (IS_ERR(phydev)) {
|
||||
pr_err("%s: Could not attach to PHY\n", dev->name);
|
||||
|
@ -1205,14 +1206,14 @@ static int smsc911x_open(struct net_device *dev)
|
|||
/* Set interrupt deassertion to 100uS */
|
||||
intcfg = ((10 << 24) | INT_CFG_IRQ_EN_);
|
||||
|
||||
if (pdata->irq_polarity) {
|
||||
if (pdata->config.irq_polarity) {
|
||||
SMSC_TRACE(IFUP, "irq polarity: active high");
|
||||
intcfg |= INT_CFG_IRQ_POL_;
|
||||
} else {
|
||||
SMSC_TRACE(IFUP, "irq polarity: active low");
|
||||
}
|
||||
|
||||
if (pdata->irq_type) {
|
||||
if (pdata->config.irq_type) {
|
||||
SMSC_TRACE(IFUP, "irq type: push-pull");
|
||||
intcfg |= INT_CFG_IRQ_TYPE_;
|
||||
} else {
|
||||
|
@ -1767,9 +1768,7 @@ static int __devinit smsc911x_init(struct net_device *dev)
|
|||
SMSC_TRACE(PROBE, "IRQ: %d", dev->irq);
|
||||
SMSC_TRACE(PROBE, "PHY will be autodetected.");
|
||||
|
||||
#if (!SMSC_CAN_USE_32BIT)
|
||||
spin_lock_init(&pdata->dev_lock);
|
||||
#endif
|
||||
|
||||
if (pdata->ioaddr == 0) {
|
||||
SMSC_WARNING(PROBE, "pdata->ioaddr: 0x00000000");
|
||||
|
@ -1910,6 +1909,7 @@ static int __devinit smsc911x_drv_probe(struct platform_device *pdev)
|
|||
{
|
||||
struct net_device *dev;
|
||||
struct smsc911x_data *pdata;
|
||||
struct smsc911x_platform_config *config = pdev->dev.platform_data;
|
||||
struct resource *res;
|
||||
unsigned int intcfg = 0;
|
||||
int res_size;
|
||||
|
@ -1918,6 +1918,13 @@ static int __devinit smsc911x_drv_probe(struct platform_device *pdev)
|
|||
|
||||
pr_info("%s: Driver version %s.\n", SMSC_CHIPNAME, SMSC_DRV_VERSION);
|
||||
|
||||
/* platform data specifies irq & dynamic bus configuration */
|
||||
if (!pdev->dev.platform_data) {
|
||||
pr_warning("%s: platform_data not provided\n", SMSC_CHIPNAME);
|
||||
retval = -ENODEV;
|
||||
goto out_0;
|
||||
}
|
||||
|
||||
res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
|
||||
"smsc911x-memory");
|
||||
if (!res)
|
||||
|
@ -1949,15 +1956,8 @@ static int __devinit smsc911x_drv_probe(struct platform_device *pdev)
|
|||
dev->irq = platform_get_irq(pdev, 0);
|
||||
pdata->ioaddr = ioremap_nocache(res->start, res_size);
|
||||
|
||||
/* copy config parameters across if present, otherwise pdata
|
||||
* defaults to zeros */
|
||||
if (pdev->dev.platform_data) {
|
||||
struct smsc911x_platform_config *config =
|
||||
pdev->dev.platform_data;
|
||||
pdata->irq_polarity = config->irq_polarity;
|
||||
pdata->irq_type = config->irq_type;
|
||||
pdata->phy_interface = config->phy_interface;
|
||||
}
|
||||
/* copy config parameters across to pdata */
|
||||
memcpy(&pdata->config, config, sizeof(pdata->config));
|
||||
|
||||
pdata->dev = dev;
|
||||
pdata->msg_enable = ((1 << debug) - 1);
|
||||
|
@ -1974,10 +1974,10 @@ static int __devinit smsc911x_drv_probe(struct platform_device *pdev)
|
|||
goto out_unmap_io_3;
|
||||
|
||||
/* configure irq polarity and type before connecting isr */
|
||||
if (pdata->irq_polarity == SMSC911X_IRQ_POLARITY_ACTIVE_HIGH)
|
||||
if (pdata->config.irq_polarity == SMSC911X_IRQ_POLARITY_ACTIVE_HIGH)
|
||||
intcfg |= INT_CFG_IRQ_POL_;
|
||||
|
||||
if (pdata->irq_type == SMSC911X_IRQ_TYPE_PUSH_PULL)
|
||||
if (pdata->config.irq_type == SMSC911X_IRQ_TYPE_PUSH_PULL)
|
||||
intcfg |= INT_CFG_IRQ_TYPE_;
|
||||
|
||||
smsc911x_reg_write(pdata, INT_CFG, intcfg);
|
||||
|
|
|
@ -21,7 +21,6 @@
|
|||
#ifndef __SMSC911X_H__
|
||||
#define __SMSC911X_H__
|
||||
|
||||
#define SMSC_CAN_USE_32BIT 1
|
||||
#define TX_FIFO_LOW_THRESHOLD ((u32)1600)
|
||||
#define SMSC911X_EEPROM_SIZE ((u32)7)
|
||||
#define USE_DEBUG 0
|
||||
|
|
|
@ -28,6 +28,7 @@
|
|||
struct smsc911x_platform_config {
|
||||
unsigned int irq_polarity;
|
||||
unsigned int irq_type;
|
||||
unsigned int flags;
|
||||
phy_interface_t phy_interface;
|
||||
};
|
||||
|
||||
|
@ -39,4 +40,8 @@ struct smsc911x_platform_config {
|
|||
#define SMSC911X_IRQ_TYPE_OPEN_DRAIN 0
|
||||
#define SMSC911X_IRQ_TYPE_PUSH_PULL 1
|
||||
|
||||
/* Constants for flags */
|
||||
#define SMSC911X_USE_16BIT (BIT(0))
|
||||
#define SMSC911X_USE_32BIT (BIT(1))
|
||||
|
||||
#endif /* __LINUX_SMSC911X_H__ */
|
||||
|
|
Loading…
Reference in a new issue