avr32: add support for EarthLCD Favr-32 board
This patch adds support for the Favr-32 board made by EarthLCD. This kit, which is also called ezLCD-101, has a 10.4" touch screen LCD panel, 16 MB 32-bit SDRAM, 8 MB parallel flash, Ethernet, audio out, USB device, SD-card slot, USART and various other connectors for cennecting stuff to SPI, I2C, GPIO, etc. Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com> Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This commit is contained in:
parent
a3bee42f05
commit
45c349b58c
|
@ -119,10 +119,15 @@ config BOARD_ATSTK1000
|
|||
config BOARD_ATNGW100
|
||||
bool "ATNGW100 Network Gateway"
|
||||
select CPU_AT32AP7000
|
||||
|
||||
config BOARD_FAVR_32
|
||||
bool "Favr-32 LCD-board"
|
||||
select CPU_AT32AP7000
|
||||
endchoice
|
||||
|
||||
source "arch/avr32/boards/atstk1000/Kconfig"
|
||||
source "arch/avr32/boards/atngw100/Kconfig"
|
||||
source "arch/avr32/boards/favr-32/Kconfig"
|
||||
|
||||
choice
|
||||
prompt "Boot loader type"
|
||||
|
|
|
@ -33,6 +33,7 @@ head-y += arch/avr32/kernel/head.o
|
|||
core-y += $(machdirs)
|
||||
core-$(CONFIG_BOARD_ATSTK1000) += arch/avr32/boards/atstk1000/
|
||||
core-$(CONFIG_BOARD_ATNGW100) += arch/avr32/boards/atngw100/
|
||||
core-$(CONFIG_BOARD_FAVR_32) += arch/avr32/boards/favr-32/
|
||||
core-$(CONFIG_LOADER_U_BOOT) += arch/avr32/boot/u-boot/
|
||||
core-y += arch/avr32/kernel/
|
||||
core-y += arch/avr32/mm/
|
||||
|
|
22
arch/avr32/boards/favr-32/Kconfig
Normal file
22
arch/avr32/boards/favr-32/Kconfig
Normal file
|
@ -0,0 +1,22 @@
|
|||
# Favr-32 customization
|
||||
|
||||
if BOARD_FAVR_32
|
||||
|
||||
config BOARD_FAVR32_ABDAC_RATE
|
||||
int "DAC target rate"
|
||||
default 44100
|
||||
range 32000 50000
|
||||
help
|
||||
Specify the target rate the internal DAC should try to match. This
|
||||
will use PLL1 to generate a frequency as close as possible to this
|
||||
rate.
|
||||
|
||||
Must be within the range 32000 to 50000, which should be suitable to
|
||||
generate most other frequencies in power of 2 steps.
|
||||
|
||||
Ex:
|
||||
48000 will also suit 24000 and 12000
|
||||
44100 will also suit 22050 and 11025
|
||||
32000 will also suit 16000 and 8000
|
||||
|
||||
endif # BOARD_FAVR_32
|
1
arch/avr32/boards/favr-32/Makefile
Normal file
1
arch/avr32/boards/favr-32/Makefile
Normal file
|
@ -0,0 +1 @@
|
|||
obj-y += setup.o flash.o
|
98
arch/avr32/boards/favr-32/flash.c
Normal file
98
arch/avr32/boards/favr-32/flash.c
Normal file
|
@ -0,0 +1,98 @@
|
|||
/*
|
||||
* Favr-32 board-specific flash initialization
|
||||
*
|
||||
* Copyright (C) 2008 Atmel Corporation
|
||||
*
|
||||
* This program is free software; you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License version 2 as
|
||||
* published by the Free Software Foundation.
|
||||
*/
|
||||
#include <linux/init.h>
|
||||
#include <linux/platform_device.h>
|
||||
#include <linux/mtd/mtd.h>
|
||||
#include <linux/mtd/partitions.h>
|
||||
#include <linux/mtd/physmap.h>
|
||||
|
||||
#include <asm/arch/smc.h>
|
||||
|
||||
static struct smc_timing flash_timing __initdata = {
|
||||
.ncs_read_setup = 0,
|
||||
.nrd_setup = 40,
|
||||
.ncs_write_setup = 0,
|
||||
.nwe_setup = 10,
|
||||
|
||||
.ncs_read_pulse = 80,
|
||||
.nrd_pulse = 40,
|
||||
.ncs_write_pulse = 65,
|
||||
.nwe_pulse = 55,
|
||||
|
||||
.read_cycle = 120,
|
||||
.write_cycle = 120,
|
||||
};
|
||||
|
||||
static struct smc_config flash_config __initdata = {
|
||||
.bus_width = 2,
|
||||
.nrd_controlled = 1,
|
||||
.nwe_controlled = 1,
|
||||
.byte_write = 1,
|
||||
};
|
||||
|
||||
static struct mtd_partition flash_parts[] = {
|
||||
{
|
||||
.name = "u-boot",
|
||||
.offset = 0x00000000,
|
||||
.size = 0x00020000, /* 128 KiB */
|
||||
.mask_flags = MTD_WRITEABLE,
|
||||
},
|
||||
{
|
||||
.name = "root",
|
||||
.offset = 0x00020000,
|
||||
.size = 0x007d0000,
|
||||
},
|
||||
{
|
||||
.name = "env",
|
||||
.offset = 0x007f0000,
|
||||
.size = 0x00010000,
|
||||
.mask_flags = MTD_WRITEABLE,
|
||||
},
|
||||
};
|
||||
|
||||
static struct physmap_flash_data flash_data = {
|
||||
.width = 2,
|
||||
.nr_parts = ARRAY_SIZE(flash_parts),
|
||||
.parts = flash_parts,
|
||||
};
|
||||
|
||||
static struct resource flash_resource = {
|
||||
.start = 0x00000000,
|
||||
.end = 0x007fffff,
|
||||
.flags = IORESOURCE_MEM,
|
||||
};
|
||||
|
||||
static struct platform_device flash_device = {
|
||||
.name = "physmap-flash",
|
||||
.id = 0,
|
||||
.resource = &flash_resource,
|
||||
.num_resources = 1,
|
||||
.dev = {
|
||||
.platform_data = &flash_data,
|
||||
},
|
||||
};
|
||||
|
||||
/* This needs to be called after the SMC has been initialized */
|
||||
static int __init favr32_flash_init(void)
|
||||
{
|
||||
int ret;
|
||||
|
||||
smc_set_timing(&flash_config, &flash_timing);
|
||||
ret = smc_set_configuration(0, &flash_config);
|
||||
if (ret < 0) {
|
||||
printk(KERN_ERR "Favr-32: failed to set NOR flash timing\n");
|
||||
return ret;
|
||||
}
|
||||
|
||||
platform_device_register(&flash_device);
|
||||
|
||||
return 0;
|
||||
}
|
||||
device_initcall(favr32_flash_init);
|
352
arch/avr32/boards/favr-32/setup.c
Normal file
352
arch/avr32/boards/favr-32/setup.c
Normal file
|
@ -0,0 +1,352 @@
|
|||
/*
|
||||
* Favr-32 board-specific setup code.
|
||||
*
|
||||
* Copyright (C) 2008 Atmel Corporation
|
||||
*
|
||||
* This program is free software; you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License version 2 as
|
||||
* published by the Free Software Foundation.
|
||||
*/
|
||||
#include <linux/clk.h>
|
||||
#include <linux/etherdevice.h>
|
||||
#include <linux/bootmem.h>
|
||||
#include <linux/fb.h>
|
||||
#include <linux/init.h>
|
||||
#include <linux/platform_device.h>
|
||||
#include <linux/types.h>
|
||||
#include <linux/linkage.h>
|
||||
#include <linux/gpio.h>
|
||||
#include <linux/leds.h>
|
||||
#include <linux/atmel-pwm-bl.h>
|
||||
#include <linux/spi/spi.h>
|
||||
#include <linux/spi/ads7846.h>
|
||||
|
||||
#include <video/atmel_lcdc.h>
|
||||
|
||||
#include <asm/setup.h>
|
||||
|
||||
#include <asm/arch/at32ap700x.h>
|
||||
#include <asm/arch/init.h>
|
||||
#include <asm/arch/board.h>
|
||||
#include <asm/arch/portmux.h>
|
||||
|
||||
/* Oscillator frequencies. These are board-specific */
|
||||
unsigned long at32_board_osc_rates[3] = {
|
||||
[0] = 32768, /* 32.768 kHz on RTC osc */
|
||||
[1] = 20000000, /* 20 MHz on osc0 */
|
||||
[2] = 12000000, /* 12 MHz on osc1 */
|
||||
};
|
||||
|
||||
/* Initialized by bootloader-specific startup code. */
|
||||
struct tag *bootloader_tags __initdata;
|
||||
|
||||
struct eth_addr {
|
||||
u8 addr[6];
|
||||
};
|
||||
static struct eth_addr __initdata hw_addr[1];
|
||||
static struct eth_platform_data __initdata eth_data[1] = {
|
||||
{
|
||||
.phy_mask = ~(1U << 1),
|
||||
},
|
||||
};
|
||||
|
||||
static int ads7843_get_pendown_state(void)
|
||||
{
|
||||
return !gpio_get_value(GPIO_PIN_PB(3));
|
||||
}
|
||||
|
||||
static struct ads7846_platform_data ads7843_data = {
|
||||
.model = 7843,
|
||||
.get_pendown_state = ads7843_get_pendown_state,
|
||||
.pressure_max = 255,
|
||||
/*
|
||||
* Values below are for debounce filtering, these can be experimented
|
||||
* with further.
|
||||
*/
|
||||
.debounce_max = 20,
|
||||
.debounce_rep = 4,
|
||||
.debounce_tol = 5,
|
||||
};
|
||||
|
||||
static struct spi_board_info __initdata spi1_board_info[] = {
|
||||
{
|
||||
/* ADS7843 touch controller */
|
||||
.modalias = "ads7846",
|
||||
.max_speed_hz = 2000000,
|
||||
.chip_select = 0,
|
||||
.bus_num = 1,
|
||||
.platform_data = &ads7843_data,
|
||||
},
|
||||
};
|
||||
|
||||
static struct fb_videomode __initdata lb104v03_modes[] = {
|
||||
{
|
||||
.name = "640x480 @ 50",
|
||||
.refresh = 50,
|
||||
.xres = 640, .yres = 480,
|
||||
.pixclock = KHZ2PICOS(25100),
|
||||
|
||||
.left_margin = 90, .right_margin = 70,
|
||||
.upper_margin = 30, .lower_margin = 15,
|
||||
.hsync_len = 12, .vsync_len = 2,
|
||||
|
||||
.sync = 0,
|
||||
.vmode = FB_VMODE_NONINTERLACED,
|
||||
},
|
||||
};
|
||||
|
||||
static struct fb_monspecs __initdata favr32_default_monspecs = {
|
||||
.manufacturer = "LG",
|
||||
.monitor = "LB104V03",
|
||||
.modedb = lb104v03_modes,
|
||||
.modedb_len = ARRAY_SIZE(lb104v03_modes),
|
||||
.hfmin = 27273,
|
||||
.hfmax = 31111,
|
||||
.vfmin = 45,
|
||||
.vfmax = 60,
|
||||
.dclkmax = 28000000,
|
||||
};
|
||||
|
||||
struct atmel_lcdfb_info __initdata favr32_lcdc_data = {
|
||||
.default_bpp = 16,
|
||||
.default_dmacon = ATMEL_LCDC_DMAEN | ATMEL_LCDC_DMA2DEN,
|
||||
.default_lcdcon2 = (ATMEL_LCDC_DISTYPE_TFT
|
||||
| ATMEL_LCDC_CLKMOD_ALWAYSACTIVE
|
||||
| ATMEL_LCDC_MEMOR_BIG),
|
||||
.default_monspecs = &favr32_default_monspecs,
|
||||
.guard_time = 2,
|
||||
};
|
||||
|
||||
static struct gpio_led favr32_leds[] = {
|
||||
{
|
||||
.name = "green",
|
||||
.gpio = GPIO_PIN_PE(19),
|
||||
.default_trigger = "heartbeat",
|
||||
.active_low = 1,
|
||||
},
|
||||
{
|
||||
.name = "red",
|
||||
.gpio = GPIO_PIN_PE(20),
|
||||
.active_low = 1,
|
||||
},
|
||||
};
|
||||
|
||||
static struct gpio_led_platform_data favr32_led_data = {
|
||||
.num_leds = ARRAY_SIZE(favr32_leds),
|
||||
.leds = favr32_leds,
|
||||
};
|
||||
|
||||
static struct platform_device favr32_led_dev = {
|
||||
.name = "leds-gpio",
|
||||
.id = 0,
|
||||
.dev = {
|
||||
.platform_data = &favr32_led_data,
|
||||
},
|
||||
};
|
||||
|
||||
/*
|
||||
* The next two functions should go away as the boot loader is
|
||||
* supposed to initialize the macb address registers with a valid
|
||||
* ethernet address. But we need to keep it around for a while until
|
||||
* we can be reasonably sure the boot loader does this.
|
||||
*
|
||||
* The phy_id is ignored as the driver will probe for it.
|
||||
*/
|
||||
static int __init parse_tag_ethernet(struct tag *tag)
|
||||
{
|
||||
int i;
|
||||
|
||||
i = tag->u.ethernet.mac_index;
|
||||
if (i < ARRAY_SIZE(hw_addr))
|
||||
memcpy(hw_addr[i].addr, tag->u.ethernet.hw_address,
|
||||
sizeof(hw_addr[i].addr));
|
||||
|
||||
return 0;
|
||||
}
|
||||
__tagtable(ATAG_ETHERNET, parse_tag_ethernet);
|
||||
|
||||
static void __init set_hw_addr(struct platform_device *pdev)
|
||||
{
|
||||
struct resource *res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
|
||||
const u8 *addr;
|
||||
void __iomem *regs;
|
||||
struct clk *pclk;
|
||||
|
||||
if (!res)
|
||||
return;
|
||||
if (pdev->id >= ARRAY_SIZE(hw_addr))
|
||||
return;
|
||||
|
||||
addr = hw_addr[pdev->id].addr;
|
||||
if (!is_valid_ether_addr(addr))
|
||||
return;
|
||||
|
||||
/*
|
||||
* Since this is board-specific code, we'll cheat and use the
|
||||
* physical address directly as we happen to know that it's
|
||||
* the same as the virtual address.
|
||||
*/
|
||||
regs = (void __iomem __force *)res->start;
|
||||
pclk = clk_get(&pdev->dev, "pclk");
|
||||
if (!pclk)
|
||||
return;
|
||||
|
||||
clk_enable(pclk);
|
||||
__raw_writel((addr[3] << 24) | (addr[2] << 16)
|
||||
| (addr[1] << 8) | addr[0], regs + 0x98);
|
||||
__raw_writel((addr[5] << 8) | addr[4], regs + 0x9c);
|
||||
clk_disable(pclk);
|
||||
clk_put(pclk);
|
||||
}
|
||||
|
||||
void __init favr32_setup_leds(void)
|
||||
{
|
||||
unsigned i;
|
||||
|
||||
for (i = 0; i < ARRAY_SIZE(favr32_leds); i++)
|
||||
at32_select_gpio(favr32_leds[i].gpio, AT32_GPIOF_OUTPUT);
|
||||
|
||||
platform_device_register(&favr32_led_dev);
|
||||
}
|
||||
|
||||
static struct atmel_pwm_bl_platform_data atmel_pwm_bl_pdata = {
|
||||
.pwm_channel = 2,
|
||||
.pwm_frequency = 200000,
|
||||
.pwm_compare_max = 345,
|
||||
.pwm_duty_max = 345,
|
||||
.pwm_duty_min = 90,
|
||||
.pwm_active_low = 1,
|
||||
.gpio_on = GPIO_PIN_PA(28),
|
||||
.on_active_low = 0,
|
||||
};
|
||||
|
||||
static struct platform_device atmel_pwm_bl_dev = {
|
||||
.name = "atmel-pwm-bl",
|
||||
.id = 0,
|
||||
.dev = {
|
||||
.platform_data = &atmel_pwm_bl_pdata,
|
||||
},
|
||||
};
|
||||
|
||||
static void __init favr32_setup_atmel_pwm_bl(void)
|
||||
{
|
||||
platform_device_register(&atmel_pwm_bl_dev);
|
||||
at32_select_gpio(atmel_pwm_bl_pdata.gpio_on, 0);
|
||||
}
|
||||
|
||||
void __init setup_board(void)
|
||||
{
|
||||
at32_map_usart(3, 0); /* USART 3 => /dev/ttyS0 */
|
||||
at32_setup_serial_console(0);
|
||||
}
|
||||
|
||||
static int __init set_abdac_rate(struct platform_device *pdev)
|
||||
{
|
||||
int retval;
|
||||
struct clk *osc1;
|
||||
struct clk *pll1;
|
||||
struct clk *abdac;
|
||||
|
||||
if (pdev == NULL)
|
||||
return -ENXIO;
|
||||
|
||||
osc1 = clk_get(NULL, "osc1");
|
||||
if (IS_ERR(osc1)) {
|
||||
retval = PTR_ERR(osc1);
|
||||
goto out;
|
||||
}
|
||||
|
||||
pll1 = clk_get(NULL, "pll1");
|
||||
if (IS_ERR(pll1)) {
|
||||
retval = PTR_ERR(pll1);
|
||||
goto out_osc1;
|
||||
}
|
||||
|
||||
abdac = clk_get(&pdev->dev, "sample_clk");
|
||||
if (IS_ERR(abdac)) {
|
||||
retval = PTR_ERR(abdac);
|
||||
goto out_pll1;
|
||||
}
|
||||
|
||||
retval = clk_set_parent(pll1, osc1);
|
||||
if (retval != 0)
|
||||
goto out_abdac;
|
||||
|
||||
/*
|
||||
* Rate is 32000 to 50000 and ABDAC oversamples 256x. Multiply, in
|
||||
* power of 2, to a value above 80 MHz. Power of 2 so it is possible
|
||||
* for the generic clock to divide it down again and 80 MHz is the
|
||||
* lowest frequency for the PLL.
|
||||
*/
|
||||
retval = clk_round_rate(pll1,
|
||||
CONFIG_BOARD_FAVR32_ABDAC_RATE * 256 * 16);
|
||||
if (retval < 0)
|
||||
goto out_abdac;
|
||||
|
||||
retval = clk_set_rate(pll1, retval);
|
||||
if (retval != 0)
|
||||
goto out_abdac;
|
||||
|
||||
retval = clk_set_parent(abdac, pll1);
|
||||
if (retval != 0)
|
||||
goto out_abdac;
|
||||
|
||||
out_abdac:
|
||||
clk_put(abdac);
|
||||
out_pll1:
|
||||
clk_put(pll1);
|
||||
out_osc1:
|
||||
clk_put(osc1);
|
||||
out:
|
||||
return retval;
|
||||
}
|
||||
|
||||
static int __init favr32_init(void)
|
||||
{
|
||||
/*
|
||||
* Favr-32 uses 32-bit SDRAM interface. Reserve the SDRAM-specific
|
||||
* pins so that nobody messes with them.
|
||||
*/
|
||||
at32_reserve_pin(GPIO_PIN_PE(0)); /* DATA[16] */
|
||||
at32_reserve_pin(GPIO_PIN_PE(1)); /* DATA[17] */
|
||||
at32_reserve_pin(GPIO_PIN_PE(2)); /* DATA[18] */
|
||||
at32_reserve_pin(GPIO_PIN_PE(3)); /* DATA[19] */
|
||||
at32_reserve_pin(GPIO_PIN_PE(4)); /* DATA[20] */
|
||||
at32_reserve_pin(GPIO_PIN_PE(5)); /* DATA[21] */
|
||||
at32_reserve_pin(GPIO_PIN_PE(6)); /* DATA[22] */
|
||||
at32_reserve_pin(GPIO_PIN_PE(7)); /* DATA[23] */
|
||||
at32_reserve_pin(GPIO_PIN_PE(8)); /* DATA[24] */
|
||||
at32_reserve_pin(GPIO_PIN_PE(9)); /* DATA[25] */
|
||||
at32_reserve_pin(GPIO_PIN_PE(10)); /* DATA[26] */
|
||||
at32_reserve_pin(GPIO_PIN_PE(11)); /* DATA[27] */
|
||||
at32_reserve_pin(GPIO_PIN_PE(12)); /* DATA[28] */
|
||||
at32_reserve_pin(GPIO_PIN_PE(13)); /* DATA[29] */
|
||||
at32_reserve_pin(GPIO_PIN_PE(14)); /* DATA[30] */
|
||||
at32_reserve_pin(GPIO_PIN_PE(15)); /* DATA[31] */
|
||||
at32_reserve_pin(GPIO_PIN_PE(26)); /* SDCS */
|
||||
|
||||
at32_select_gpio(GPIO_PIN_PB(3), 0); /* IRQ from ADS7843 */
|
||||
|
||||
at32_add_system_devices();
|
||||
|
||||
at32_add_device_usart(0);
|
||||
|
||||
set_hw_addr(at32_add_device_eth(0, ð_data[0]));
|
||||
|
||||
spi1_board_info[0].irq = gpio_to_irq(GPIO_PIN_PB(3));
|
||||
|
||||
set_abdac_rate(at32_add_device_abdac(0));
|
||||
|
||||
at32_add_device_pwm(1 << atmel_pwm_bl_pdata.pwm_channel);
|
||||
at32_add_device_spi(1, spi1_board_info, ARRAY_SIZE(spi1_board_info));
|
||||
at32_add_device_mci(0, NULL);
|
||||
at32_add_device_usba(0, NULL);
|
||||
at32_add_device_lcdc(0, &favr32_lcdc_data, fbmem_start, fbmem_size, 0);
|
||||
|
||||
favr32_setup_leds();
|
||||
|
||||
favr32_setup_atmel_pwm_bl();
|
||||
|
||||
return 0;
|
||||
}
|
||||
postcore_initcall(favr32_init);
|
Loading…
Reference in a new issue