pinctrl: mxs: atomically switch mux and drive strength config
commitda6c2addf6
upstream. To set the mux mode of a pin two bits must be set. Up to now this is implemented using the following idiom: writel(mask, reg + CLR); writel(value, reg + SET); . This however results in the mux mode being 0 between the two writes. On my machine there is an IC's reset pin connected to LCD_D20. The bootloader configures this pin as GPIO output-high (i.e. not holding the IC in reset). When Linux reconfigures the pin to GPIO the short time LCD_D20 is muxed as LCD_D20 instead of GPIO_1_20 is enough to confuse the connected IC. The same problem is present for the pin's drive strength setting which is reset to low drive strength before using the right value. So instead of relying on the hardware to modify the register setting using two writes implement the bit toggling using read-modify-write. Fixes:17723111e6
("pinctrl: add pinctrl-mxs support") Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit is contained in:
parent
dee763a4d3
commit
485b0f1194
|
@ -194,6 +194,16 @@ static int mxs_pinctrl_get_func_groups(struct pinctrl_dev *pctldev,
|
||||||
return 0;
|
return 0;
|
||||||
}
|
}
|
||||||
|
|
||||||
|
static void mxs_pinctrl_rmwl(u32 value, u32 mask, u8 shift, void __iomem *reg)
|
||||||
|
{
|
||||||
|
u32 tmp;
|
||||||
|
|
||||||
|
tmp = readl(reg);
|
||||||
|
tmp &= ~(mask << shift);
|
||||||
|
tmp |= value << shift;
|
||||||
|
writel(tmp, reg);
|
||||||
|
}
|
||||||
|
|
||||||
static int mxs_pinctrl_set_mux(struct pinctrl_dev *pctldev, unsigned selector,
|
static int mxs_pinctrl_set_mux(struct pinctrl_dev *pctldev, unsigned selector,
|
||||||
unsigned group)
|
unsigned group)
|
||||||
{
|
{
|
||||||
|
@ -211,8 +221,7 @@ static int mxs_pinctrl_set_mux(struct pinctrl_dev *pctldev, unsigned selector,
|
||||||
reg += bank * 0x20 + pin / 16 * 0x10;
|
reg += bank * 0x20 + pin / 16 * 0x10;
|
||||||
shift = pin % 16 * 2;
|
shift = pin % 16 * 2;
|
||||||
|
|
||||||
writel(0x3 << shift, reg + CLR);
|
mxs_pinctrl_rmwl(g->muxsel[i], 0x3, shift, reg);
|
||||||
writel(g->muxsel[i] << shift, reg + SET);
|
|
||||||
}
|
}
|
||||||
|
|
||||||
return 0;
|
return 0;
|
||||||
|
@ -279,8 +288,7 @@ static int mxs_pinconf_group_set(struct pinctrl_dev *pctldev,
|
||||||
/* mA */
|
/* mA */
|
||||||
if (config & MA_PRESENT) {
|
if (config & MA_PRESENT) {
|
||||||
shift = pin % 8 * 4;
|
shift = pin % 8 * 4;
|
||||||
writel(0x3 << shift, reg + CLR);
|
mxs_pinctrl_rmwl(ma, 0x3, shift, reg);
|
||||||
writel(ma << shift, reg + SET);
|
|
||||||
}
|
}
|
||||||
|
|
||||||
/* vol */
|
/* vol */
|
||||||
|
|
Loading…
Reference in a new issue