diff --git a/drivers/staging/fbtft/Kconfig b/drivers/staging/fbtft/Kconfig index 883ff5b8fdab..0bfc7764312e 100644 --- a/drivers/staging/fbtft/Kconfig +++ b/drivers/staging/fbtft/Kconfig @@ -117,6 +117,12 @@ config FB_TFT_SSD1289 help Framebuffer support for SSD1289 +config FB_TFT_SSD1305 + tristate "FB driver for the SSD1305 OLED Controller" + depends on FB_TFT + help + Framebuffer support for SSD1305 + config FB_TFT_SSD1306 tristate "FB driver for the SSD1306 OLED Controller" depends on FB_TFT diff --git a/drivers/staging/fbtft/Makefile b/drivers/staging/fbtft/Makefile index 4f9071d96d01..1ddc764039a0 100644 --- a/drivers/staging/fbtft/Makefile +++ b/drivers/staging/fbtft/Makefile @@ -21,6 +21,7 @@ obj-$(CONFIG_FB_TFT_RA8875) += fb_ra8875.o obj-$(CONFIG_FB_TFT_S6D02A1) += fb_s6d02a1.o obj-$(CONFIG_FB_TFT_S6D1121) += fb_s6d1121.o obj-$(CONFIG_FB_TFT_SSD1289) += fb_ssd1289.o +obj-$(CONFIG_FB_TFT_SSD1305) += fb_ssd1305.o obj-$(CONFIG_FB_TFT_SSD1306) += fb_ssd1306.o obj-$(CONFIG_FB_TFT_SSD1331) += fb_ssd1331.o obj-$(CONFIG_FB_TFT_SSD1351) += fb_ssd1351.o diff --git a/drivers/staging/fbtft/fb_ssd1305.c b/drivers/staging/fbtft/fb_ssd1305.c new file mode 100644 index 000000000000..4b38c3fadd60 --- /dev/null +++ b/drivers/staging/fbtft/fb_ssd1305.c @@ -0,0 +1,216 @@ +/* + * FB driver for the SSD1305 OLED Controller + * + * based on SSD1306 driver by Noralf Tronnes + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#include +#include +#include +#include +#include + +#include "fbtft.h" + +#define DRVNAME "fb_ssd1305" + +#define WIDTH 128 +#define HEIGHT 64 + +/* + * write_reg() caveat: + * + * This doesn't work because D/C has to be LOW for both values: + * write_reg(par, val1, val2); + * + * Do it like this: + * write_reg(par, val1); + * write_reg(par, val2); + */ + +/* Init sequence taken from the Adafruit SSD1306 Arduino library */ +static int init_display(struct fbtft_par *par) +{ + par->fbtftops.reset(par); + + if (par->gamma.curves[0] == 0) { + mutex_lock(&par->gamma.lock); + if (par->info->var.yres == 64) + par->gamma.curves[0] = 0xCF; + else + par->gamma.curves[0] = 0x8F; + mutex_unlock(&par->gamma.lock); + } + + /* Set Display OFF */ + write_reg(par, 0xAE); + + /* Set Display Clock Divide Ratio/ Oscillator Frequency */ + write_reg(par, 0xD5); + write_reg(par, 0x80); + + /* Set Multiplex Ratio */ + write_reg(par, 0xA8); + if (par->info->var.yres == 64) + write_reg(par, 0x3F); + else + write_reg(par, 0x1F); + + /* Set Display Offset */ + write_reg(par, 0xD3); + write_reg(par, 0x0); + + /* Set Display Start Line */ + write_reg(par, 0x40 | 0x0); + + /* Charge Pump Setting */ + write_reg(par, 0x8D); + /* A[2] = 1b, Enable charge pump during display on */ + write_reg(par, 0x14); + + /* Set Memory Addressing Mode */ + write_reg(par, 0x20); + /* Vertical addressing mode */ + write_reg(par, 0x01); + + /* + * Set Segment Re-map + * column address 127 is mapped to SEG0 + */ + write_reg(par, 0xA0 | ((par->info->var.rotate == 180) ? 0x0 : 0x1)); + + /* + * Set COM Output Scan Direction + * remapped mode. Scan from COM[N-1] to COM0 + */ + write_reg(par, ((par->info->var.rotate == 180) ? 0xC8 : 0xC0)); + + /* Set COM Pins Hardware Configuration */ + write_reg(par, 0xDA); + if (par->info->var.yres == 64) { + /* A[4]=1b, Alternative COM pin configuration */ + write_reg(par, 0x12); + } else { + /* A[4]=0b, Sequential COM pin configuration */ + write_reg(par, 0x02); + } + + /* Set Pre-charge Period */ + write_reg(par, 0xD9); + write_reg(par, 0xF1); + + /* + * Entire Display ON + * Resume to RAM content display. Output follows RAM content + */ + write_reg(par, 0xA4); + + /* + * Set Normal Display + * 0 in RAM: OFF in display panel + * 1 in RAM: ON in display panel + */ + write_reg(par, 0xA6); + + /* Set Display ON */ + write_reg(par, 0xAF); + + return 0; +} + +static void set_addr_win(struct fbtft_par *par, int xs, int ys, int xe, int ye) +{ + /* Set Lower Column Start Address for Page Addressing Mode */ + write_reg(par, 0x00 | ((par->info->var.rotate == 180) ? 0x0 : 0x4)); + /* Set Higher Column Start Address for Page Addressing Mode */ + write_reg(par, 0x10 | 0x0); + /* Set Display Start Line */ + write_reg(par, 0x40 | 0x0); +} + +static int blank(struct fbtft_par *par, bool on) +{ + if (on) + write_reg(par, 0xAE); + else + write_reg(par, 0xAF); + return 0; +} + +/* Gamma is used to control Contrast */ +static int set_gamma(struct fbtft_par *par, unsigned long *curves) +{ + curves[0] &= 0xFF; + /* Set Contrast Control for BANK0 */ + write_reg(par, 0x81); + write_reg(par, curves[0]); + + return 0; +} + +static int write_vmem(struct fbtft_par *par, size_t offset, size_t len) +{ + u16 *vmem16 = (u16 *)par->info->screen_buffer; + u8 *buf = par->txbuf.buf; + int x, y, i; + int ret; + + for (x = 0; x < par->info->var.xres; x++) { + for (y = 0; y < par->info->var.yres / 8; y++) { + *buf = 0x00; + for (i = 0; i < 8; i++) + *buf |= (vmem16[(y * 8 + i) * + par->info->var.xres + x] ? + 1 : 0) << i; + buf++; + } + } + + /* Write data */ + gpio_set_value(par->gpio.dc, 1); + ret = par->fbtftops.write(par, par->txbuf.buf, + par->info->var.xres * par->info->var.yres / + 8); + if (ret < 0) + dev_err(par->info->device, "write failed and returned: %d\n", + ret); + return ret; +} + +static struct fbtft_display display = { + .regwidth = 8, + .width = WIDTH, + .height = HEIGHT, + .txbuflen = WIDTH * HEIGHT / 8, + .gamma_num = 1, + .gamma_len = 1, + .gamma = "00", + .fbtftops = { + .write_vmem = write_vmem, + .init_display = init_display, + .set_addr_win = set_addr_win, + .blank = blank, + .set_gamma = set_gamma, + }, +}; + +FBTFT_REGISTER_DRIVER(DRVNAME, "solomon,ssd1305", &display); + +MODULE_ALIAS("spi:" DRVNAME); +MODULE_ALIAS("platform:" DRVNAME); +MODULE_ALIAS("spi:ssd1305"); +MODULE_ALIAS("platform:ssd1305"); + +MODULE_DESCRIPTION("SSD1305 OLED Driver"); +MODULE_AUTHOR("Alexey Mednyy"); +MODULE_LICENSE("GPL");