ARM: at91/boards: use -EINVAL for invalid gpio

this will allow to use gpio_is_valid

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
This commit is contained in:
Jean-Christophe PLAGNIOL-VILLARD 2011-11-25 01:51:06 +08:00 committed by Arnd Bergmann
parent 1a2d9156b5
commit 63b4c29678
38 changed files with 192 additions and 65 deletions

View file

@ -70,6 +70,8 @@ static struct macb_platform_data __initdata onearm_eth_data = {
static struct at91_usbh_data __initdata onearm_usbh_data = {
.ports = 1,
.vbus_pin = {-EINVAL, -EINVAL},
.overcurrent_pin= {-EINVAL, -EINVAL},
};
static struct at91_udc_data __initdata onearm_udc_data = {

View file

@ -75,6 +75,8 @@ static void __init afeb9260_init_early(void)
*/
static struct at91_usbh_data __initdata afeb9260_usbh_data = {
.ports = 1,
.vbus_pin = {-EINVAL, -EINVAL},
.overcurrent_pin= {-EINVAL, -EINVAL},
};
/*
@ -82,7 +84,7 @@ static struct at91_usbh_data __initdata afeb9260_usbh_data = {
*/
static struct at91_udc_data __initdata afeb9260_udc_data = {
.vbus_pin = AT91_PIN_PC5,
.pullup_pin = 0, /* pull-up driven by UDC */
.pullup_pin = -EINVAL, /* pull-up driven by UDC */
};
@ -138,6 +140,7 @@ static struct atmel_nand_data __initdata afeb9260_nand_data = {
.bus_width_16 = 0,
.parts = afeb9260_nand_partition,
.num_parts = ARRAY_SIZE(afeb9260_nand_partition),
.det_pin = -EINVAL,
};
@ -149,6 +152,7 @@ static struct at91_mmc_data __initdata afeb9260_mmc_data = {
.wp_pin = AT91_PIN_PC4,
.slot_b = 1,
.wire4 = 1,
.vcc_pin = -EINVAL,
};
@ -169,6 +173,8 @@ static struct i2c_board_info __initdata afeb9260_i2c_devices[] = {
static struct at91_cf_data afeb9260_cf_data = {
.chipselect = 4,
.irq_pin = AT91_PIN_PA6,
.det_pin = -EINVAL,
.vcc_pin = -EINVAL,
.rst_pin = AT91_PIN_PA7,
.flags = AT91_CF_TRUE_IDE,
};

View file

@ -62,6 +62,8 @@ static void __init cam60_init_early(void)
*/
static struct at91_usbh_data __initdata cam60_usbh_data = {
.ports = 1,
.vbus_pin = {-EINVAL, -EINVAL},
.overcurrent_pin= {-EINVAL, -EINVAL},
};
@ -135,7 +137,7 @@ static struct mtd_partition __initdata cam60_nand_partition[] = {
static struct atmel_nand_data __initdata cam60_nand_data = {
.ale = 21,
.cle = 22,
// .det_pin = ... not there
.det_pin = -EINVAL,
.rdy_pin = AT91_PIN_PA9,
.enable_pin = AT91_PIN_PA7,
.parts = cam60_nand_partition,

View file

@ -70,6 +70,8 @@ static void __init cap9adk_init_early(void)
*/
static struct at91_usbh_data __initdata cap9adk_usbh_data = {
.ports = 2,
.vbus_pin = {-EINVAL, -EINVAL},
.overcurrent_pin= {-EINVAL, -EINVAL},
};
/*
@ -144,9 +146,9 @@ static struct spi_board_info cap9adk_spi_devices[] = {
*/
static struct at91_mmc_data __initdata cap9adk_mmc_data = {
.wire4 = 1,
// .det_pin = ... not connected
// .wp_pin = ... not connected
// .vcc_pin = ... not connected
.det_pin = -EINVAL,
.wp_pin = -EINVAL,
.vcc_pin = -EINVAL,
};
@ -154,6 +156,7 @@ static struct at91_mmc_data __initdata cap9adk_mmc_data = {
* MACB Ethernet device
*/
static struct macb_platform_data __initdata cap9adk_macb_data = {
.phy_irq_pin = -EINVAL,
.is_rmii = 1,
};
@ -172,8 +175,8 @@ static struct mtd_partition __initdata cap9adk_nand_partitions[] = {
static struct atmel_nand_data __initdata cap9adk_nand_data = {
.ale = 21,
.cle = 22,
// .det_pin = ... not connected
// .rdy_pin = ... not connected
.det_pin = -EINVAL,
.rdy_pin = -EINVAL,
.enable_pin = AT91_PIN_PD15,
.parts = cap9adk_nand_partitions,
.num_parts = ARRAY_SIZE(cap9adk_nand_partitions),
@ -351,7 +354,7 @@ static struct atmel_lcdfb_info __initdata cap9adk_lcdc_data;
* AC97
*/
static struct ac97c_platform_data cap9adk_ac97_data = {
// .reset_pin = ... not connected
.reset_pin = -EINVAL,
};

View file

@ -64,6 +64,8 @@ static struct macb_platform_data __initdata carmeva_eth_data = {
static struct at91_usbh_data __initdata carmeva_usbh_data = {
.ports = 2,
.vbus_pin = {-EINVAL, -EINVAL},
.overcurrent_pin= {-EINVAL, -EINVAL},
};
static struct at91_udc_data __initdata carmeva_udc_data = {
@ -75,8 +77,8 @@ static struct at91_udc_data __initdata carmeva_udc_data = {
// static struct at91_cf_data __initdata carmeva_cf_data = {
// .det_pin = AT91_PIN_PB0,
// .rst_pin = AT91_PIN_PC5,
// .irq_pin = ... not connected
// .vcc_pin = ... always powered
// .irq_pin = -EINVAL,
// .vcc_pin = -EINVAL,
// };
static struct at91_mmc_data __initdata carmeva_mmc_data = {
@ -84,6 +86,7 @@ static struct at91_mmc_data __initdata carmeva_mmc_data = {
.wire4 = 1,
.det_pin = AT91_PIN_PB10,
.wp_pin = AT91_PIN_PC14,
.vcc_pin = -EINVAL,
};
static struct spi_board_info carmeva_spi_devices[] = {

View file

@ -86,6 +86,8 @@ static void __init cpu9krea_init_early(void)
*/
static struct at91_usbh_data __initdata cpu9krea_usbh_data = {
.ports = 2,
.vbus_pin = {-EINVAL, -EINVAL},
.overcurrent_pin= {-EINVAL, -EINVAL},
};
/*
@ -93,13 +95,14 @@ static struct at91_usbh_data __initdata cpu9krea_usbh_data = {
*/
static struct at91_udc_data __initdata cpu9krea_udc_data = {
.vbus_pin = AT91_PIN_PC8,
.pullup_pin = 0, /* pull-up driven by UDC */
.pullup_pin = -EINVAL, /* pull-up driven by UDC */
};
/*
* MACB Ethernet device
*/
static struct macb_platform_data __initdata cpu9krea_macb_data = {
.phy_irq_pin = -EINVAL,
.is_rmii = 1,
};
@ -112,6 +115,7 @@ static struct atmel_nand_data __initdata cpu9krea_nand_data = {
.rdy_pin = AT91_PIN_PC13,
.enable_pin = AT91_PIN_PC14,
.bus_width_16 = 0,
.det_pin = -EINVAL,
};
#ifdef CONFIG_MACH_CPU9260
@ -337,6 +341,8 @@ static struct at91_mmc_data __initdata cpu9krea_mmc_data = {
.slot_b = 0,
.wire4 = 1,
.det_pin = AT91_PIN_PA29,
.wp_pin = -EINVAL,
.vcc_pin = -EINVAL,
};
static void __init cpu9krea_board_init(void)

View file

@ -83,11 +83,14 @@ static void __init cpuat91_init_early(void)
}
static struct macb_platform_data __initdata cpuat91_eth_data = {
.phy_irq_pin = -EINVAL,
.is_rmii = 1,
};
static struct at91_usbh_data __initdata cpuat91_usbh_data = {
.ports = 1,
.vbus_pin = {-EINVAL, -EINVAL},
.overcurrent_pin= {-EINVAL, -EINVAL},
};
static struct at91_udc_data __initdata cpuat91_udc_data = {
@ -98,6 +101,8 @@ static struct at91_udc_data __initdata cpuat91_udc_data = {
static struct at91_mmc_data __initdata cpuat91_mmc_data = {
.det_pin = AT91_PIN_PC2,
.wire4 = 1,
.wp_pin = -EINVAL,
.vcc_pin = -EINVAL,
};
static struct physmap_flash_data cpuat91_flash_data = {

View file

@ -65,11 +65,13 @@ static struct macb_platform_data __initdata csb337_eth_data = {
static struct at91_usbh_data __initdata csb337_usbh_data = {
.ports = 2,
.vbus_pin = {-EINVAL, -EINVAL},
.overcurrent_pin= {-EINVAL, -EINVAL},
};
static struct at91_udc_data __initdata csb337_udc_data = {
// this has no VBUS sensing pin
.pullup_pin = AT91_PIN_PA24,
.vbus_pin = -EINVAL,
};
static struct i2c_board_info __initdata csb337_i2c_devices[] = {
@ -98,6 +100,7 @@ static struct at91_mmc_data __initdata csb337_mmc_data = {
.slot_b = 0,
.wire4 = 1,
.wp_pin = AT91_PIN_PD6,
.vcc_pin = -EINVAL,
};
static struct spi_board_info csb337_spi_devices[] = {

View file

@ -59,6 +59,8 @@ static struct macb_platform_data __initdata csb637_eth_data = {
static struct at91_usbh_data __initdata csb637_usbh_data = {
.ports = 2,
.vbus_pin = {-EINVAL, -EINVAL},
.overcurrent_pin= {-EINVAL, -EINVAL},
};
static struct at91_udc_data __initdata csb637_udc_data = {

View file

@ -50,6 +50,7 @@ static void __init ek_init_early(void)
static struct atmel_nand_data __initdata ek_nand_data = {
.ale = 21,
.cle = 22,
.det_pin = -EINVAL,
.rdy_pin = AT91_PIN_PC8,
.enable_pin = AT91_PIN_PC14,
};

View file

@ -67,6 +67,8 @@ static struct macb_platform_data __initdata eb9200_eth_data = {
static struct at91_usbh_data __initdata eb9200_usbh_data = {
.ports = 2,
.vbus_pin = {-EINVAL, -EINVAL},
.overcurrent_pin= {-EINVAL, -EINVAL},
};
static struct at91_udc_data __initdata eb9200_udc_data = {
@ -75,15 +77,18 @@ static struct at91_udc_data __initdata eb9200_udc_data = {
};
static struct at91_cf_data __initdata eb9200_cf_data = {
.irq_pin = -EINVAL,
.det_pin = AT91_PIN_PB0,
.vcc_pin = -EINVAL,
.rst_pin = AT91_PIN_PC5,
// .irq_pin = ... not connected
// .vcc_pin = ... always powered
};
static struct at91_mmc_data __initdata eb9200_mmc_data = {
.slot_b = 0,
.wire4 = 1,
.det_pin = -EINVAL,
.wp_pin = -EINVAL,
.vcc_pin = -EINVAL,
};
static struct i2c_board_info __initdata eb9200_i2c_devices[] = {

View file

@ -71,11 +71,16 @@ static struct macb_platform_data __initdata ecb_at91eth_data = {
static struct at91_usbh_data __initdata ecb_at91usbh_data = {
.ports = 1,
.vbus_pin = {-EINVAL, -EINVAL},
.overcurrent_pin= {-EINVAL, -EINVAL},
};
static struct at91_mmc_data __initdata ecb_at91mmc_data = {
.slot_b = 0,
.wire4 = 1,
.det_pin = -EINVAL,
.wp_pin = -EINVAL,
.vcc_pin = -EINVAL,
};

View file

@ -54,6 +54,8 @@ static struct macb_platform_data __initdata eco920_eth_data = {
static struct at91_usbh_data __initdata eco920_usbh_data = {
.ports = 1,
.vbus_pin = {-EINVAL, -EINVAL},
.overcurrent_pin= {-EINVAL, -EINVAL},
};
static struct at91_udc_data __initdata eco920_udc_data = {
@ -64,6 +66,9 @@ static struct at91_udc_data __initdata eco920_udc_data = {
static struct at91_mmc_data __initdata eco920_mmc_data = {
.slot_b = 0,
.wire4 = 0,
.det_pin = -EINVAL,
.wp_pin = -EINVAL,
.vcc_pin = -EINVAL,
};
static struct physmap_flash_data eco920_flash_data = {

View file

@ -52,12 +52,14 @@ static void __init flexibity_init_early(void)
/* USB Host port */
static struct at91_usbh_data __initdata flexibity_usbh_data = {
.ports = 2,
.vbus_pin = {-EINVAL, -EINVAL},
.overcurrent_pin= {-EINVAL, -EINVAL},
};
/* USB Device port */
static struct at91_udc_data __initdata flexibity_udc_data = {
.vbus_pin = AT91_PIN_PC5,
.pullup_pin = 0, /* pull-up driven by UDC */
.pullup_pin = -EINVAL, /* pull-up driven by UDC */
};
/* SPI devices */
@ -76,6 +78,7 @@ static struct at91_mmc_data __initdata flexibity_mmc_data = {
.wire4 = 1,
.det_pin = AT91_PIN_PC9,
.wp_pin = AT91_PIN_PC4,
.vcc_pin = -EINVAL,
};
/* LEDs */

View file

@ -106,6 +106,8 @@ static void __init foxg20_init_early(void)
*/
static struct at91_usbh_data __initdata foxg20_usbh_data = {
.ports = 2,
.vbus_pin = {-EINVAL, -EINVAL},
.overcurrent_pin= {-EINVAL, -EINVAL},
};
/*
@ -113,7 +115,7 @@ static struct at91_usbh_data __initdata foxg20_usbh_data = {
*/
static struct at91_udc_data __initdata foxg20_udc_data = {
.vbus_pin = AT91_PIN_PC6,
.pullup_pin = 0, /* pull-up driven by UDC */
.pullup_pin = -EINVAL, /* pull-up driven by UDC */
};
@ -147,6 +149,9 @@ static struct macb_platform_data __initdata foxg20_macb_data = {
static struct at91_mmc_data __initdata foxg20_mmc_data = {
.slot_b = 1,
.wire4 = 1,
.det_pin = -EINVAL,
.wp_pin = -EINVAL,
.vcc_pin = -EINVAL,
};

View file

@ -80,6 +80,8 @@ static void __init gsia18s_init_early(void)
*/
static struct at91_usbh_data __initdata usbh_data = {
.ports = 2,
.vbus_pin = {-EINVAL, -EINVAL},
.overcurrent_pin= {-EINVAL, -EINVAL},
};
/*
@ -87,7 +89,7 @@ static struct at91_usbh_data __initdata usbh_data = {
*/
static struct at91_udc_data __initdata udc_data = {
.vbus_pin = AT91_PIN_PA22,
.pullup_pin = 0, /* pull-up driven by UDC */
.pullup_pin = -EINVAL, /* pull-up driven by UDC */
};
/*
@ -530,6 +532,7 @@ static struct i2c_board_info __initdata gsia18s_i2c_devices[] = {
static struct at91_cf_data __initdata gsia18s_cf1_data = {
.irq_pin = AT91_PIN_PA27,
.det_pin = AT91_PIN_PB30,
.vcc_pin = -EINVAL,
.rst_pin = AT91_PIN_PB31,
.chipselect = 5,
.flags = AT91_CF_TRUE_IDE,

View file

@ -68,6 +68,8 @@ static struct macb_platform_data __initdata kafa_eth_data = {
static struct at91_usbh_data __initdata kafa_usbh_data = {
.ports = 1,
.vbus_pin = {-EINVAL, -EINVAL},
.overcurrent_pin= {-EINVAL, -EINVAL},
};
static struct at91_udc_data __initdata kafa_udc_data = {

View file

@ -76,6 +76,8 @@ static struct macb_platform_data __initdata kb9202_eth_data = {
static struct at91_usbh_data __initdata kb9202_usbh_data = {
.ports = 1,
.vbus_pin = {-EINVAL, -EINVAL},
.overcurrent_pin= {-EINVAL, -EINVAL},
};
static struct at91_udc_data __initdata kb9202_udc_data = {
@ -87,6 +89,8 @@ static struct at91_mmc_data __initdata kb9202_mmc_data = {
.det_pin = AT91_PIN_PB2,
.slot_b = 0,
.wire4 = 1,
.wp_pin = -EINVAL,
.vcc_pin = -EINVAL,
};
static struct mtd_partition __initdata kb9202_nand_partition[] = {
@ -100,7 +104,7 @@ static struct mtd_partition __initdata kb9202_nand_partition[] = {
static struct atmel_nand_data __initdata kb9202_nand_data = {
.ale = 22,
.cle = 21,
// .det_pin = ... not there
.det_pin = -EINVAL,
.rdy_pin = AT91_PIN_PC29,
.enable_pin = AT91_PIN_PC28,
.parts = kb9202_nand_partition,

View file

@ -72,6 +72,7 @@ static void __init neocore926_init_early(void)
static struct at91_usbh_data __initdata neocore926_usbh_data = {
.ports = 2,
.vbus_pin = { AT91_PIN_PA24, AT91_PIN_PA21 },
.overcurrent_pin= {-EINVAL, -EINVAL},
};
/*
@ -79,7 +80,7 @@ static struct at91_usbh_data __initdata neocore926_usbh_data = {
*/
static struct at91_udc_data __initdata neocore926_udc_data = {
.vbus_pin = AT91_PIN_PA25,
.pullup_pin = 0, /* pull-up driven by UDC */
.pullup_pin = -EINVAL, /* pull-up driven by UDC */
};
@ -149,6 +150,7 @@ static struct at91_mmc_data __initdata neocore926_mmc_data = {
.wire4 = 1,
.det_pin = AT91_PIN_PE18,
.wp_pin = AT91_PIN_PE19,
.vcc_pin = -EINVAL,
};
@ -190,6 +192,7 @@ static struct atmel_nand_data __initdata neocore926_nand_data = {
.enable_pin = AT91_PIN_PD15,
.parts = neocore926_nand_partition,
.num_parts = ARRAY_SIZE(neocore926_nand_partition),
.det_pin = -EINVAL,
};
static struct sam9_smc_config __initdata neocore926_nand_smc_config = {

View file

@ -107,6 +107,8 @@ static void __init add_device_pcontrol(void)
*/
static struct at91_usbh_data __initdata usbh_data = {
.ports = 2,
.vbus_pin = {-EINVAL, -EINVAL},
.overcurrent_pin= {-EINVAL, -EINVAL},
};

View file

@ -67,6 +67,8 @@ static struct macb_platform_data __initdata picotux200_eth_data = {
static struct at91_usbh_data __initdata picotux200_usbh_data = {
.ports = 1,
.vbus_pin = {-EINVAL, -EINVAL},
.overcurrent_pin= {-EINVAL, -EINVAL},
};
static struct at91_mmc_data __initdata picotux200_mmc_data = {
@ -74,6 +76,7 @@ static struct at91_mmc_data __initdata picotux200_mmc_data = {
.slot_b = 0,
.wire4 = 1,
.wp_pin = AT91_PIN_PA17,
.vcc_pin = -EINVAL,
};
#define PICOTUX200_FLASH_BASE AT91_CHIPSELECT_0

View file

@ -77,6 +77,8 @@ static void __init ek_init_early(void)
*/
static struct at91_usbh_data __initdata ek_usbh_data = {
.ports = 2,
.vbus_pin = {-EINVAL, -EINVAL},
.overcurrent_pin= {-EINVAL, -EINVAL},
};
/*
@ -84,7 +86,7 @@ static struct at91_usbh_data __initdata ek_usbh_data = {
*/
static struct at91_udc_data __initdata ek_udc_data = {
.vbus_pin = AT91_PIN_PC5,
.pullup_pin = 0, /* pull-up driven by UDC */
.pullup_pin = -EINVAL, /* pull-up driven by UDC */
};
/*
@ -133,7 +135,7 @@ static struct mtd_partition __initdata ek_nand_partition[] = {
static struct atmel_nand_data __initdata ek_nand_data = {
.ale = 21,
.cle = 22,
// .det_pin = ... not connected
.det_pin = -EINVAL,
.rdy_pin = AT91_PIN_PC13,
.enable_pin = AT91_PIN_PC14,
.parts = ek_nand_partition,
@ -172,9 +174,9 @@ static void __init ek_add_device_nand(void)
static struct at91_mmc_data __initdata ek_mmc_data = {
.slot_b = 0,
.wire4 = 1,
// .det_pin = ... not connected
// .wp_pin = ... not connected
// .vcc_pin = ... not connected
.det_pin = -EINVAL,
.wp_pin = -EINVAL,
.vcc_pin = -EINVAL,
};
/*

View file

@ -72,6 +72,8 @@ static struct macb_platform_data __initdata dk_eth_data = {
static struct at91_usbh_data __initdata dk_usbh_data = {
.ports = 2,
.vbus_pin = {-EINVAL, -EINVAL},
.overcurrent_pin= {-EINVAL, -EINVAL},
};
static struct at91_udc_data __initdata dk_udc_data = {
@ -80,16 +82,19 @@ static struct at91_udc_data __initdata dk_udc_data = {
};
static struct at91_cf_data __initdata dk_cf_data = {
.irq_pin = -EINVAL,
.det_pin = AT91_PIN_PB0,
.vcc_pin = -EINVAL,
.rst_pin = AT91_PIN_PC5,
// .irq_pin = ... not connected
// .vcc_pin = ... always powered
};
#ifndef CONFIG_MTD_AT91_DATAFLASH_CARD
static struct at91_mmc_data __initdata dk_mmc_data = {
.slot_b = 0,
.wire4 = 1,
.det_pin = -EINVAL,
.wp_pin = -EINVAL,
.vcc_pin = -EINVAL,
};
#endif
@ -143,7 +148,7 @@ static struct atmel_nand_data __initdata dk_nand_data = {
.cle = 21,
.det_pin = AT91_PIN_PB1,
.rdy_pin = AT91_PIN_PC2,
// .enable_pin = ... not there
.enable_pin = -EINVAL,
.parts = dk_nand_partition,
.num_parts = ARRAY_SIZE(dk_nand_partition),
};

View file

@ -72,6 +72,8 @@ static struct macb_platform_data __initdata ek_eth_data = {
static struct at91_usbh_data __initdata ek_usbh_data = {
.ports = 2,
.vbus_pin = {-EINVAL, -EINVAL},
.overcurrent_pin= {-EINVAL, -EINVAL},
};
static struct at91_udc_data __initdata ek_udc_data = {
@ -85,6 +87,7 @@ static struct at91_mmc_data __initdata ek_mmc_data = {
.slot_b = 0,
.wire4 = 1,
.wp_pin = AT91_PIN_PA17,
.vcc_pin = -EINVAL,
};
#endif

View file

@ -70,6 +70,8 @@ static struct macb_platform_data rsi_ews_eth_data __initdata = {
*/
static struct at91_usbh_data rsi_ews_usbh_data __initdata = {
.ports = 1,
.vbus_pin = {-EINVAL, -EINVAL},
.overcurrent_pin= {-EINVAL, -EINVAL},
};
/*

View file

@ -72,6 +72,8 @@ static void __init ek_init_early(void)
*/
static struct at91_usbh_data __initdata ek_usbh_data = {
.ports = 2,
.vbus_pin = {-EINVAL, -EINVAL},
.overcurrent_pin= {-EINVAL, -EINVAL},
};
/*
@ -79,7 +81,7 @@ static struct at91_usbh_data __initdata ek_usbh_data = {
*/
static struct at91_udc_data __initdata ek_udc_data = {
.vbus_pin = AT91_PIN_PC5,
.pullup_pin = 0, /* pull-up driven by UDC */
.pullup_pin = -EINVAL, /* pull-up driven by UDC */
};
@ -134,7 +136,7 @@ static struct mtd_partition __initdata ek_nand_partition[] = {
static struct atmel_nand_data __initdata ek_nand_data = {
.ale = 21,
.cle = 22,
// .det_pin = ... not connected
.det_pin = -EINVAL,
.rdy_pin = AT91_PIN_PC13,
.enable_pin = AT91_PIN_PC14,
.parts = ek_nand_partition,
@ -176,7 +178,7 @@ static struct at91_mmc_data __initdata ek_mmc_data = {
.wire4 = 1,
.det_pin = AT91_PIN_PC8,
.wp_pin = AT91_PIN_PC4,
// .vcc_pin = ... not connected
.vcc_pin = -EINVAL,
};
static void __init ek_board_init(void)

View file

@ -75,6 +75,8 @@ static void __init ek_init_early(void)
*/
static struct at91_usbh_data __initdata ek_usbh_data = {
.ports = 2,
.vbus_pin = {-EINVAL, -EINVAL},
.overcurrent_pin= {-EINVAL, -EINVAL},
};
/*
@ -82,7 +84,7 @@ static struct at91_usbh_data __initdata ek_usbh_data = {
*/
static struct at91_udc_data __initdata ek_udc_data = {
.vbus_pin = AT91_PIN_PC5,
.pullup_pin = 0, /* pull-up driven by UDC */
.pullup_pin = -EINVAL, /* pull-up driven by UDC */
};
@ -176,7 +178,7 @@ static struct mtd_partition __initdata ek_nand_partition[] = {
static struct atmel_nand_data __initdata ek_nand_data = {
.ale = 21,
.cle = 22,
// .det_pin = ... not connected
.det_pin = -EINVAL,
.rdy_pin = AT91_PIN_PC13,
.enable_pin = AT91_PIN_PC14,
.parts = ek_nand_partition,
@ -223,9 +225,9 @@ static void __init ek_add_device_nand(void)
static struct at91_mmc_data __initdata ek_mmc_data = {
.slot_b = 1,
.wire4 = 1,
// .det_pin = ... not connected
// .wp_pin = ... not connected
// .vcc_pin = ... not connected
.det_pin = -EINVAL,
.wp_pin = -EINVAL,
.vcc_pin = -EINVAL,
};

View file

@ -151,6 +151,8 @@ static void __init ek_add_device_dm9000(void) {}
*/
static struct at91_usbh_data __initdata ek_usbh_data = {
.ports = 2,
.vbus_pin = {-EINVAL, -EINVAL},
.overcurrent_pin= {-EINVAL, -EINVAL},
};
@ -159,7 +161,7 @@ static struct at91_usbh_data __initdata ek_usbh_data = {
*/
static struct at91_udc_data __initdata ek_udc_data = {
.vbus_pin = AT91_PIN_PB29,
.pullup_pin = 0, /* pull-up driven by UDC */
.pullup_pin = -EINVAL, /* pull-up driven by UDC */
};
@ -182,7 +184,7 @@ static struct mtd_partition __initdata ek_nand_partition[] = {
static struct atmel_nand_data __initdata ek_nand_data = {
.ale = 22,
.cle = 21,
// .det_pin = ... not connected
.det_pin = -EINVAL,
.rdy_pin = AT91_PIN_PC15,
.enable_pin = AT91_PIN_PC14,
.parts = ek_nand_partition,
@ -345,6 +347,9 @@ static struct spi_board_info ek_spi_devices[] = {
*/
static struct at91_mmc_data __initdata ek_mmc_data = {
.wire4 = 1,
.det_pin = -EINVAL,
.wp_pin = -EINVAL,
.vcc_pin = -EINVAL,
};
#endif /* CONFIG_SPI_ATMEL_* */

View file

@ -74,6 +74,7 @@ static void __init ek_init_early(void)
static struct at91_usbh_data __initdata ek_usbh_data = {
.ports = 2,
.vbus_pin = { AT91_PIN_PA24, AT91_PIN_PA21 },
.overcurrent_pin= {-EINVAL, -EINVAL},
};
/*
@ -81,7 +82,7 @@ static struct at91_usbh_data __initdata ek_usbh_data = {
*/
static struct at91_udc_data __initdata ek_udc_data = {
.vbus_pin = AT91_PIN_PA25,
.pullup_pin = 0, /* pull-up driven by UDC */
.pullup_pin = -EINVAL, /* pull-up driven by UDC */
};
@ -151,7 +152,7 @@ static struct at91_mmc_data __initdata ek_mmc_data = {
.wire4 = 1,
.det_pin = AT91_PIN_PE18,
.wp_pin = AT91_PIN_PE19,
// .vcc_pin = ... not connected
.vcc_pin = -EINVAL,
};
@ -183,7 +184,7 @@ static struct mtd_partition __initdata ek_nand_partition[] = {
static struct atmel_nand_data __initdata ek_nand_data = {
.ale = 21,
.cle = 22,
// .det_pin = ... not connected
.det_pin = -EINVAL,
.rdy_pin = AT91_PIN_PA22,
.enable_pin = AT91_PIN_PD15,
.parts = ek_nand_partition,
@ -353,6 +354,7 @@ static void __init ek_add_device_buttons(void) {}
* reset_pin is not connected: NRST
*/
static struct ac97c_platform_data ek_ac97_data = {
.reset_pin = -EINVAL,
};

View file

@ -86,6 +86,8 @@ static void __init ek_init_early(void)
*/
static struct at91_usbh_data __initdata ek_usbh_data = {
.ports = 2,
.vbus_pin = {-EINVAL, -EINVAL},
.overcurrent_pin= {-EINVAL, -EINVAL},
};
/*
@ -93,7 +95,7 @@ static struct at91_usbh_data __initdata ek_usbh_data = {
*/
static struct at91_udc_data __initdata ek_udc_data = {
.vbus_pin = AT91_PIN_PC5,
.pullup_pin = 0, /* pull-up driven by UDC */
.pullup_pin = -EINVAL, /* pull-up driven by UDC */
};
@ -163,6 +165,7 @@ static struct atmel_nand_data __initdata ek_nand_data = {
.cle = 22,
.rdy_pin = AT91_PIN_PC13,
.enable_pin = AT91_PIN_PC14,
.det_pin = -EINVAL,
.parts = ek_nand_partition,
.num_parts = ARRAY_SIZE(ek_nand_partition),
};
@ -210,6 +213,7 @@ static struct mci_platform_data __initdata ek_mmc_data = {
.slot[1] = {
.bus_width = 4,
.detect_pin = AT91_PIN_PC9,
.wp_pin = -EINVAL,
},
};
@ -218,6 +222,8 @@ static struct at91_mmc_data __initdata ek_mmc_data = {
.slot_b = 1, /* Only one slot so use slot B */
.wire4 = 1,
.det_pin = AT91_PIN_PC9,
.wp_pin = -EINVAL,
.vcc_pin = -EINVAL,
};
#endif
@ -227,6 +233,7 @@ static void __init ek_add_device_mmc(void)
if (ek_have_2mmc()) {
ek_mmc_data.slot[0].bus_width = 4;
ek_mmc_data.slot[0].detect_pin = AT91_PIN_PC2;
ek_mmc_data.slot[0].wp_pin = -1;
}
at91_add_device_mci(0, &ek_mmc_data);
#else

View file

@ -69,6 +69,7 @@ static void __init ek_init_early(void)
static struct at91_usbh_data __initdata ek_usbh_hs_data = {
.ports = 2,
.vbus_pin = {AT91_PIN_PD1, AT91_PIN_PD3},
.overcurrent_pin= {-EINVAL, -EINVAL},
};
@ -100,6 +101,7 @@ static struct mci_platform_data __initdata mci0_data = {
.slot[0] = {
.bus_width = 4,
.detect_pin = AT91_PIN_PD10,
.wp_pin = -EINVAL,
},
};
@ -143,6 +145,7 @@ static struct atmel_nand_data __initdata ek_nand_data = {
.cle = 22,
.rdy_pin = AT91_PIN_PC8,
.enable_pin = AT91_PIN_PC14,
.det_pin = -EINVAL,
.parts = ek_nand_partition,
.num_parts = ARRAY_SIZE(ek_nand_partition),
};
@ -330,6 +333,7 @@ static void __init ek_add_device_buttons(void) {}
* reset_pin is not connected: NRST
*/
static struct ac97c_platform_data ek_ac97_data = {
.reset_pin = -EINVAL,
};

View file

@ -67,8 +67,8 @@ static struct usba_platform_data __initdata ek_usba_udc_data = {
static struct at91_mmc_data __initdata ek_mmc_data = {
.wire4 = 1,
.det_pin = AT91_PIN_PA15,
// .wp_pin = ... not connected
// .vcc_pin = ... not connected
.wp_pin = -EINVAL,
.vcc_pin = -EINVAL,
};
@ -91,7 +91,7 @@ static struct mtd_partition __initdata ek_nand_partition[] = {
static struct atmel_nand_data __initdata ek_nand_data = {
.ale = 21,
.cle = 22,
// .det_pin = ... not connected
.det_pin = -EINVAL,
.rdy_pin = AT91_PIN_PD17,
.enable_pin = AT91_PIN_PB6,
.parts = ek_nand_partition,
@ -204,6 +204,7 @@ static struct atmel_lcdfb_info __initdata ek_lcdc_data;
* reset_pin is not connected: NRST
*/
static struct ac97c_platform_data ek_ac97_data = {
.reset_pin = -EINVAL,
};

View file

@ -57,15 +57,19 @@ static void __init snapper9260_init_early(void)
static struct at91_usbh_data __initdata snapper9260_usbh_data = {
.ports = 2,
.vbus_pin = {-EINVAL, -EINVAL},
.overcurrent_pin= {-EINVAL, -EINVAL},
};
static struct at91_udc_data __initdata snapper9260_udc_data = {
.vbus_pin = SNAPPER9260_IO_EXP_GPIO(5),
.vbus_active_low = 1,
.vbus_polled = 1,
.pullup_pin = -EINVAL,
};
static struct macb_platform_data snapper9260_macb_data = {
.phy_irq_pin = -EINVAL,
.is_rmii = 1,
};
@ -104,6 +108,8 @@ static struct atmel_nand_data __initdata snapper9260_nand_data = {
.parts = snapper9260_nand_partitions,
.num_parts = ARRAY_SIZE(snapper9260_nand_partitions),
.bus_width_16 = 0,
.enable_pin = -EINVAL,
.det_pin = -EINVAL,
};
static struct sam9_smc_config __initdata snapper9260_nand_smc_config = {

View file

@ -85,6 +85,7 @@ static struct atmel_nand_data __initdata nand_data = {
.rdy_pin = AT91_PIN_PC13,
.enable_pin = AT91_PIN_PC14,
.bus_width_16 = 0,
.det_pin = -EINVAL,
};
static struct sam9_smc_config __initdata nand_smc_config = {
@ -122,12 +123,17 @@ static void __init add_device_nand(void)
static struct mci_platform_data __initdata mmc_data = {
.slot[0] = {
.bus_width = 4,
.detect_pin = -1;
.wp_pin = -1;
},
};
#else
static struct at91_mmc_data __initdata mmc_data = {
.slot_b = 0,
.wire4 = 1,
.det_pin = -EINVAL,
.wp_pin = -EINVAL,
.vcc_pin = -EINVAL,
};
#endif
@ -137,6 +143,8 @@ static struct at91_mmc_data __initdata mmc_data = {
*/
static struct at91_usbh_data __initdata usbh_data = {
.ports = 2,
.vbus_pin = {-EINVAL, -EINVAL},
.overcurrent_pin= {-EINVAL, -EINVAL},
};
@ -145,12 +153,12 @@ static struct at91_usbh_data __initdata usbh_data = {
*/
static struct at91_udc_data __initdata portuxg20_udc_data = {
.vbus_pin = AT91_PIN_PC7,
.pullup_pin = 0, /* pull-up driven by UDC */
.pullup_pin = -EINVAL, /* pull-up driven by UDC */
};
static struct at91_udc_data __initdata stamp9g20evb_udc_data = {
.vbus_pin = AT91_PIN_PA22,
.pullup_pin = 0, /* pull-up driven by UDC */
.pullup_pin = -EINVAL, /* pull-up driven by UDC */
};

View file

@ -66,6 +66,8 @@ static void __init ek_init_early(void)
*/
static struct at91_usbh_data __initdata ek_usbh_data = {
.ports = 2,
.vbus_pin = {-EINVAL, -EINVAL},
.overcurrent_pin= {-EINVAL, -EINVAL},
};
/*
@ -73,7 +75,7 @@ static struct at91_usbh_data __initdata ek_usbh_data = {
*/
static struct at91_udc_data __initdata ek_udc_data = {
.vbus_pin = AT91_PIN_PB11,
.pullup_pin = 0, /* pull-up driven by UDC */
.pullup_pin = -EINVAL, /* pull-up driven by UDC */
};
static void __init ek_add_device_udc(void)
@ -193,7 +195,7 @@ static struct mtd_partition __initdata ek_nand_partition[] = {
static struct atmel_nand_data __initdata ek_nand_data = {
.ale = 21,
.cle = 22,
// .det_pin = ... not connected
.det_pin = -EINVAL,
.rdy_pin = AT91_PIN_PA22,
.enable_pin = AT91_PIN_PD15,
.parts = ek_nand_partition,

View file

@ -120,6 +120,8 @@ static struct macb_platform_data __initdata yl9200_eth_data = {
*/
static struct at91_usbh_data __initdata yl9200_usbh_data = {
.ports = 1, /* PQFP version of AT91RM9200 */
.vbus_pin = {-EINVAL, -EINVAL},
.overcurrent_pin= {-EINVAL, -EINVAL},
};
/*
@ -137,8 +139,9 @@ static struct at91_udc_data __initdata yl9200_udc_data = {
*/
static struct at91_mmc_data __initdata yl9200_mmc_data = {
.det_pin = AT91_PIN_PB9,
// .wp_pin = ... not connected
.wire4 = 1,
.wp_pin = -EINVAL,
.vcc_pin = -EINVAL,
};
/*
@ -175,7 +178,7 @@ static struct mtd_partition __initdata yl9200_nand_partition[] = {
static struct atmel_nand_data __initdata yl9200_nand_data = {
.ale = 6,
.cle = 7,
// .det_pin = ... not connected
.det_pin = -EINVAL,
.rdy_pin = AT91_PIN_PC14, /* R/!B (Sheet10) */
.enable_pin = AT91_PIN_PC15, /* !CE (Sheet10) */
.parts = yl9200_nand_partition,

View file

@ -44,10 +44,10 @@
/* USB Device */
struct at91_udc_data {
u8 vbus_pin; /* high == host powering us */
int vbus_pin; /* high == host powering us */
u8 vbus_active_low; /* vbus polarity */
u8 vbus_polled; /* Use polling, not interrupt */
u8 pullup_pin; /* active == D+ pulled up */
int pullup_pin; /* active == D+ pulled up */
u8 pullup_active_low; /* true == pullup_pin is active low */
};
extern void __init at91_add_device_udc(struct at91_udc_data *data);
@ -57,10 +57,10 @@ extern void __init at91_add_device_usba(struct usba_platform_data *data);
/* Compact Flash */
struct at91_cf_data {
u8 irq_pin; /* I/O IRQ */
u8 det_pin; /* Card detect */
u8 vcc_pin; /* power switching */
u8 rst_pin; /* card reset */
int irq_pin; /* I/O IRQ */
int det_pin; /* Card detect */
int vcc_pin; /* power switching */
int rst_pin; /* card reset */
u8 chipselect; /* EBI Chip Select number */
u8 flags;
#define AT91_CF_TRUE_IDE 0x01
@ -71,11 +71,11 @@ extern void __init at91_add_device_cf(struct at91_cf_data *data);
/* MMC / SD */
/* at91_mci platform config */
struct at91_mmc_data {
u8 det_pin; /* card detect IRQ */
int det_pin; /* card detect IRQ */
unsigned slot_b:1; /* uses Slot B */
unsigned wire4:1; /* (SD) supports DAT0..DAT3 */
u8 wp_pin; /* (SD) writeprotect detect */
u8 vcc_pin; /* power switching (high == on) */
int wp_pin; /* (SD) writeprotect detect */
int vcc_pin; /* power switching (high == on) */
};
extern void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data);
@ -87,10 +87,10 @@ extern void __init at91_add_device_eth(struct macb_platform_data *data);
/* USB Host */
struct at91_usbh_data {
u8 ports; /* number of ports on root hub */
u8 vbus_pin[2]; /* port power-control pin */
int vbus_pin[2]; /* port power-control pin */
u8 vbus_pin_inverted;
u8 overcurrent_supported;
u8 overcurrent_pin[2];
int overcurrent_pin[2];
u8 overcurrent_status[2];
u8 overcurrent_changed[2];
};
@ -100,9 +100,9 @@ extern void __init at91_add_device_usbh_ehci(struct at91_usbh_data *data);
/* NAND / SmartMedia */
struct atmel_nand_data {
u8 enable_pin; /* chip enable */
u8 det_pin; /* card detect */
u8 rdy_pin; /* ready/busy */
int enable_pin; /* chip enable */
int det_pin; /* card detect */
int rdy_pin; /* ready/busy */
u8 rdy_pin_active_low; /* rdy_pin value is inverted */
u8 ale; /* address line number connected to ALE */
u8 cle; /* address line number connected to CLE */

View file

@ -10,7 +10,7 @@
struct macb_platform_data {
u32 phy_mask;
u8 phy_irq_pin; /* PHY IRQ */
int phy_irq_pin; /* PHY IRQ */
u8 is_rmii; /* using RMII interface? */
};