[PATCH] libata: use FLUSH_EXT only when driver is larger than LBA28 limit
Many drives support LBA48 even when its capacity is smaller than 1<<28, as LBA48 is required for many functionalities. FLUSH_EXT is mandatory for drives w/ LBA48 support. Interestingly, at least one of such drives (ST960812A) has problems dealing with FLUSH_EXT. It eventually completes the command but takes around 7 seconds to finish in many cases thus drastically slowing down IO transactions. This seems to be a firmware bug which sneaked into production probably because no other ATA driver including linux IDE issues FLUSH_EXT to drives which report support for LBA48 & FLUSH_EXT but is smaller than 1<<28 blocks. This patch adds ATA_DFLAG_FLUSH_EXT which is set iff the drive supports LBA48 & FLUSH_EXT and is larger than LBA28 limit. Both cache flush paths are updated to issue FLUSH_EXT only when the flag is set. Note that the changed behavior is more inline with the rest of libata. libata prefers shorter commands whenever possible. Signed-off-by: Tejun Heo <htejun@gmail.com> Cc: Danny Kukawka <dkukawka@novell.com> Cc: Stefan Seyfried <seife@novell.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
This commit is contained in:
parent
648a88be4a
commit
6fc49adb94
|
@ -1457,6 +1457,10 @@ int ata_dev_configure(struct ata_device *dev)
|
|||
if (ata_id_has_lba48(id)) {
|
||||
dev->flags |= ATA_DFLAG_LBA48;
|
||||
lba_desc = "LBA48";
|
||||
|
||||
if (dev->n_sectors >= (1UL << 28) &&
|
||||
ata_id_has_flush_ext(id))
|
||||
dev->flags |= ATA_DFLAG_FLUSH_EXT;
|
||||
}
|
||||
|
||||
/* config NCQ */
|
||||
|
@ -5128,7 +5132,7 @@ int ata_flush_cache(struct ata_device *dev)
|
|||
if (!ata_try_flush_cache(dev))
|
||||
return 0;
|
||||
|
||||
if (ata_id_has_flush_ext(dev->id))
|
||||
if (dev->flags & ATA_DFLAG_FLUSH_EXT)
|
||||
cmd = ATA_CMD_FLUSH_EXT;
|
||||
else
|
||||
cmd = ATA_CMD_FLUSH;
|
||||
|
|
|
@ -1027,8 +1027,7 @@ static unsigned int ata_scsi_flush_xlat(struct ata_queued_cmd *qc, const u8 *scs
|
|||
tf->flags |= ATA_TFLAG_DEVICE;
|
||||
tf->protocol = ATA_PROT_NODATA;
|
||||
|
||||
if ((qc->dev->flags & ATA_DFLAG_LBA48) &&
|
||||
(ata_id_has_flush_ext(qc->dev->id)))
|
||||
if (qc->dev->flags & ATA_DFLAG_FLUSH_EXT)
|
||||
tf->command = ATA_CMD_FLUSH_EXT;
|
||||
else
|
||||
tf->command = ATA_CMD_FLUSH;
|
||||
|
|
|
@ -140,6 +140,7 @@ enum {
|
|||
ATA_DFLAG_LBA48 = (1 << 1), /* device supports LBA48 */
|
||||
ATA_DFLAG_CDB_INTR = (1 << 2), /* device asserts INTRQ when ready for CDB */
|
||||
ATA_DFLAG_NCQ = (1 << 3), /* device supports NCQ */
|
||||
ATA_DFLAG_FLUSH_EXT = (1 << 4), /* do FLUSH_EXT instead of FLUSH */
|
||||
ATA_DFLAG_CFG_MASK = (1 << 8) - 1,
|
||||
|
||||
ATA_DFLAG_PIO = (1 << 8), /* device limited to PIO mode */
|
||||
|
|
Loading…
Reference in a new issue