redonkable/remarkable-linux
redonkable/remarkable-linux
1
0
Fork 0
Code Releases Activity

This pull request contains Broadcom ARM64 based SoC Device Tree changes for

Browse source 
4.10, please pull the following:
 
 - Robin updates the Northstart 2 DTS to use the generic IOMMU binding
 
 - Scott renames the Broadcom Northstar 2 binding document to use a standard name
   including the brcm vendor prefix
 
 - Kamal adds the QSPI Device Tree node to the Northstar 2 SoC and updates the
   Northstar 2 SVK reference board DTS file with it enabled.
 
 - Rob adds the Device Tree node for the Broadcom PDC (mailbox) hardware to the
   Northstar 2 SoC
 
 - Jon enables the SDIO1 block and adds proper PCIe PHYs Device Tree nodes to the
   Northstar 2 SoC
 
 - Ray adds required properties NAND controller properties to make NAND work on
   the Northstar 2 SVK board, this was submitted as a 4.9 fixes and is included
   here to resolve DTS file merges
 
 - Andrea removes an incorrect power LED from the Raspberry Pi 3 DTS
 
 - Andreas fixes the compatible string for the BCM2837 (Raspberry Pi 3)
 
 - Eric defines standard pinctrl groups in the BCM2835 GPIO node
 
 - Gerd adds definitions for the pinctrl groups and updates the PWM, I2C and SDHCI nodes
   to use their appropriate pinctrl functions
 
 - Linus adds names for the Raspberry Pi GPIO lines based on the datasheet
 
 - Martin adds the DT binding and nodes for the Raspberry Pi firmware thermal block
 
 - Stefan fixes a few typos with respect to the BCM2835 mailbox binding example and
   Device Tree nodes he also uses the proper DTSI file to define the USB host mode
   for the USB Device Tree nodes
 -----BEGIN PGP SIGNATURE-----
 
 iQIcBAABCAAGBQJYM9SvAAoJEIfQlpxEBwcE80YQAOfjCKEXNSWJEAMpgsCo1oEf
 6peBNi+y6AZCkNa+B1L9G2RY1B63OJKb+0HzAzj07cqbfu6r9UGhJEncnvuTnt6Q
 iLZqoxDAKINNDT4tQBvPfdI8mF7ChNQ1RaJEKRh5/eaz9feKbp0QP216oNyzdOTX
 4fUCBfgAxl6q1aNv4f4tcTdy30NllQddulLumYq5W7ElAP3CYeUGszoJ6npDqX6Z
 p2p42OMczOoU0xDH/a5BJBQW/ZbylCgFOSnGtQp6RnzOB6iBxKYDOCkMRfVLIPSg
 uC+7XSEpYAxNPRAHE5JxtADEdDKZ4zdKne8SpadixBPY8vAWguEhiOAFRqTKYpXr
 UY8itk9NMx8BnI6Fl4hU6tFs3Yx9+6PdHX0nWeR1OE2gzYpnVKOdeeS3+nWHctWm
 Z2wyglSvEpzMpaCzr2/rgDXW30BUTGtRCD7rYJ7MhwItkXm4yIN8pkLw83Zxss4d
 3J30QQoQ5s9Fye0Or4Z/PQiw3AtUJnH1u59BAE2GmrHVgs4pUaxuU4lt+LYBZtoM
 hA+pzFDeNmK/fOumjFhmvZwrCG1AON2cJRExMG6l3x9sxV2FDw1Awr4sina7ZFcO
 pbkvHmTXcGHNh7kqHeEU51r4tkkA97ZHeKGrntRSfsMNyu74xzOSsjEEf5MKMm5s
 2xX2RhehADTDa5xPDJwG
 =a4fP
 -----END PGP SIGNATURE-----

Merge tag 'arm-soc/for-4.10/devicetree-arm64' of http://github.com/Broadcom/stblinux into next/dt64

Pull "Broadcom devicetree-arm64 changes for 4.10" from Florian Fainelli:

This pull request contains Broadcom ARM64 based SoC Device Tree changes for
4.10, please pull the following:

- Robin updates the Northstart 2 DTS to use the generic IOMMU binding

- Scott renames the Broadcom Northstar 2 binding document to use a standard name
  including the brcm vendor prefix

- Kamal adds the QSPI Device Tree node to the Northstar 2 SoC and updates the
  Northstar 2 SVK reference board DTS file with it enabled.

- Rob adds the Device Tree node for the Broadcom PDC (mailbox) hardware to the
  Northstar 2 SoC

- Jon enables the SDIO1 block and adds proper PCIe PHYs Device Tree nodes to the
  Northstar 2 SoC

- Ray adds required properties NAND controller properties to make NAND work on
  the Northstar 2 SVK board, this was submitted as a 4.9 fixes and is included
  here to resolve DTS file merges

- Andrea removes an incorrect power LED from the Raspberry Pi 3 DTS

- Andreas fixes the compatible string for the BCM2837 (Raspberry Pi 3)

- Eric defines standard pinctrl groups in the BCM2835 GPIO node

- Gerd adds definitions for the pinctrl groups and updates the PWM, I2C and SDHCI nodes
  to use their appropriate pinctrl functions

- Linus adds names for the Raspberry Pi GPIO lines based on the datasheet

- Martin adds the DT binding and nodes for the Raspberry Pi firmware thermal block

- Stefan fixes a few typos with respect to the BCM2835 mailbox binding example and
  Device Tree nodes he also uses the proper DTSI file to define the USB host mode
  for the USB Device Tree nodes

* tag 'arm-soc/for-4.10/devicetree-arm64' of http://github.com/Broadcom/stblinux: (23 commits)
  arm64: dts: NS2: Add PCI PHYs
  arm64: dts: NS2: enable sdio1
  ARM64: dts: bcm2837-rpi-3-b: remove incorrect pwr LED
  ARM64: bcm2835: dts: add thermal node to device-tree of bcm2837
  ARM: bcm2835: Add names for the Raspberry Pi GPIO lines
  ARM: bcm2835: dts: add thermal node to device-tree of bcm283x
  dt: bindings: add thermal device driver for bcm2835
  arm64: dts: Add Broadcom Northstar2 device tree entries for PDC driver.
  ARM: dts: bcm283x: fix typo in mailbox address
  DT: binding: bcm2835-mbox: fix address typo in example
  ARM64: dts: bcm2835: Fix bcm2837 compatible string
  arm64: dts: Update Broadcom NS2 to generic IOMMU binding
  arm64: dts: Updated NAND DT properties for NS2 SVK
  arm64: dts: rename ns2.txt to brcm,ns2.txt
  ARM64: dts: Add QSPI Device Tree node for NS2
  ARM64: dts: bcm283x: Use dtsi for USB host mode
  ARM: dts: bcm283x: drop alt3 from &gpio
  ARM: dts: bcm283x: add pinctrl group to &sdhci, drop pins from &gpio
  ARM: dts: bcm283x: add pinctrl group to &i2c1, drop pins from &gpio
  ARM: dts: bcm283x: add pinctrl group to &i2c0, drop pins from &gpio
  ...
This commit is contained in:
Arnd Bergmann 2016-11-30 17:57:26 +01:00
parent f21b65881c e687607116
commit 7b88f1a489
21 changed files with 701 additions and 30 deletions
Show stats Download patch file Download diff file Expand all files Collapse all files

0
Documentation/devicetree/bindings/arm/bcm/ns2.txt → Documentation/devicetree/bindings/arm/bcm/brcm,ns2.txt
View file

2
Documentation/devicetree/bindings/mailbox/brcm,bcm2835-mbox.txt
View file

@ -12,7 +12,7 @@ Required properties:
Example:
mailbox: mailbox@7e00b800 {
mailbox: mailbox@7e00b880 {
compatible = "brcm,bcm2835-mbox";
reg = <0x7e00b880 0x40>;
interrupts = <0 1>;

17
Documentation/devicetree/bindings/thermal/brcm,bcm2835-thermal.txt Normal file
View file

@ -0,0 +1,17 @@
Binding for Thermal Sensor driver for BCM2835 SoCs.
Required parameters:
-------------------
compatible: should be one of: "brcm,bcm2835-thermal",
"brcm,bcm2836-thermal" or "brcm,bcm2837-thermal"
reg: Address range of the thermal registers.
clocks: Phandle of the clock used by the thermal sensor.
Example:
thermal: thermal@7e212000 {
compatible = "brcm,bcm2835-thermal";
reg = <0x7e212000 0x8>;
clocks = <&clocks BCM2835_CLOCK_TSENS>;
};

67
arch/arm/boot/dts/bcm2835-rpi-a-plus.dts
View file

@ -22,7 +22,72 @@
};
&gpio {
pinctrl-0 = <&gpioout &alt0 &i2s_alt0 &alt3>;
/*
* This is based on the unreleased schematic for the Model A+.
*
* Legend:
* "NC" = not connected (no rail from the SoC)
* "FOO" = GPIO line named "FOO" on the schematic
* "FOO_N" = GPIO line named "FOO" on schematic, active low
*/
gpio-line-names = "SDA0",
"SCL0",
"SDA1",
"SCL1",
"GPIO_GCLK",
"GPIO5",
"GPIO6",
"SPI_CE1_N",
"SPI_CE0_N",
"SPI_MISO",
"SPI_MOSI",
"SPI_SCLK",
"GPIO12",
"GPIO13",
/* Serial port */
"TXD0",
"RXD0",
"GPIO16",
"GPIO17",
"GPIO18",
"GPIO19",
"GPIO20",
"GPIO21",
"GPIO22",
"GPIO23",
"GPIO24",
"GPIO25",
"GPIO26",
"GPIO27",
"SDA0",
"SCL0",
"NC", /* GPIO30 */
"NC", /* GPIO31 */
"NC", /* GPIO32 */
"NC", /* GPIO33 */
"NC", /* GPIO34 */
"PWR_LOW_N", /* GPIO35 */
"NC", /* GPIO36 */
"NC", /* GPIO37 */
"NC", /* GPIO38 */
"NC", /* GPIO39 */
"PWM0_OUT", /* GPIO40 */
"CAM_GPIO0", /* GPIO41 */
"NC", /* GPIO42 */
"NC", /* GPIO43 */
"NC", /* GPIO44 */
"PWM1_OUT", /* GPIO45 */
"HDMI_HPD_N",
"STATUS_LED",
/* Used by SD Card */
"SD_CLK_R",
"SD_CMD_R",
"SD_DATA0_R",
"SD_DATA1_R",
"SD_DATA2_R",
"SD_DATA3_R";
pinctrl-0 = <&gpioout &alt0 &i2s_alt0>;
/* I2S interface */
i2s_alt0: i2s_alt0 {

69
arch/arm/boot/dts/bcm2835-rpi-a.dts
View file

@ -15,7 +15,74 @@
};
&gpio {
pinctrl-0 = <&gpioout &alt0 &i2s_alt2 &alt3>;
/*
* Taken from Raspberry-Pi-Rev-1.0-Model-AB-Schematics.pdf
* RPI00021 sheet 02
*
* Legend:
* "NC" = not connected (no rail from the SoC)
* "FOO" = GPIO line named "FOO" on the schematic
* "FOO_N" = GPIO line named "FOO" on schematic, active low
*/
gpio-line-names = "SDA0",
"SCL0",
"SDA1",
"SCL1",
"GPIO_GCLK",
"CAM_CLK",
"LAN_RUN",
"SPI_CE1_N",
"SPI_CE0_N",
"SPI_MISO",
"SPI_MOSI",
"SPI_SCLK",
"NC", /* GPIO12 */
"NC", /* GPIO13 */
/* Serial port */
"TXD0",
"RXD0",
"STATUS_LED_N",
"GPIO17",
"GPIO18",
"NC", /* GPIO19 */
"NC", /* GPIO20 */
"GPIO21",
"GPIO22",
"GPIO23",
"GPIO24",
"GPIO25",
"NC", /* GPIO26 */
"CAM_GPIO",
/* Binary number representing build/revision */
"CONFIG0",
"CONFIG1",
"CONFIG2",
"CONFIG3",
"NC", /* GPIO32 */
"NC", /* GPIO33 */
"NC", /* GPIO34 */
"NC", /* GPIO35 */
"NC", /* GPIO36 */
"NC", /* GPIO37 */
"NC", /* GPIO38 */
"NC", /* GPIO39 */
"PWM0_OUT",
"NC", /* GPIO41 */
"NC", /* GPIO42 */
"NC", /* GPIO43 */
"NC", /* GPIO44 */
"PWM1_OUT",
"HDMI_HPD_P",
"SD_CARD_DET",
/* Used by SD Card */
"SD_CLK_R",
"SD_CMD_R",
"SD_DATA0_R",
"SD_DATA1_R",
"SD_DATA2_R",
"SD_DATA3_R";
pinctrl-0 = <&gpioout &alt0 &i2s_alt2>;
/* I2S interface */
i2s_alt2: i2s_alt2 {

68
arch/arm/boot/dts/bcm2835-rpi-b-plus.dts
View file

@ -23,7 +23,73 @@
};
&gpio {
pinctrl-0 = <&gpioout &alt0 &i2s_alt0 &alt3>;
/*
* Taken from Raspberry-Pi-B-Plus-V1.2-Schematics.pdf
* RPI-BPLUS sheet 1
*
* Legend:
* "NC" = not connected (no rail from the SoC)
* "FOO" = GPIO line named "FOO" on the schematic
* "FOO_N" = GPIO line named "FOO" on schematic, active low
*/
gpio-line-names = "SDA0",
"SCL0",
"SDA1",
"SCL1",
"GPIO_GCLK",
"GPIO5",
"GPIO6",
"SPI_CE1_N",
"SPI_CE0_N",
"SPI_MISO",
"SPI_MOSI",
"SPI_SCLK",
"GPIO12",
"GPIO13",
/* Serial port */
"TXD0",
"RXD0",
"GPIO16",
"GPIO17",
"GPIO18",
"GPIO19",
"GPIO20",
"GPIO21",
"GPIO22",
"GPIO23",
"GPIO24",
"GPIO25",
"GPIO26",
"GPIO27",
"SDA0",
"SCL0",
"NC", /* GPIO30 */
"LAN_RUN", /* GPIO31 */
"CAM_GPIO1", /* GPIO32 */
"NC", /* GPIO33 */
"NC", /* GPIO34 */
"PWR_LOW_N", /* GPIO35 */
"NC", /* GPIO36 */
"NC", /* GPIO37 */
"NC", /* GPIO38 */
"NC", /* GPIO39 */
"PWM0_OUT", /* GPIO40 */
"CAM_GPIO0", /* GPIO41 */
"NC", /* GPIO42 */
"NC", /* GPIO43 */
"ETHCLK", /* GPIO44 */
"PWM1_OUT", /* GPIO45 */
"HDMI_HPD_N",
"STATUS_LED",
/* Used by SD Card */
"SD_CLK_R",
"SD_CMD_R",
"SD_DATA0_R",
"SD_DATA1_R",
"SD_DATA2_R",
"SD_DATA3_R";
pinctrl-0 = <&gpioout &alt0 &i2s_alt0>;
/* I2S interface */
i2s_alt0: i2s_alt0 {

68
arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts
View file

@ -16,7 +16,73 @@
};
&gpio {
pinctrl-0 = <&gpioout &alt0 &i2s_alt2 &alt3>;
/*
* Taken from Raspberry-Pi-Rev-2.0-Model-AB-Schematics.pdf
* RPI00022 sheet 02
*
* Legend:
* "NC" = not connected (no rail from the SoC)
* "FOO" = GPIO line named "FOO" on the schematic
* "FOO_N" = GPIO line named "FOO" on schematic, active low
*/
gpio-line-names = "SDA0",
"SCL0",
"SDA1",
"SCL1",
"GPIO_GCLK",
"CAM_CLK",
"LAN_RUN",
"SPI_CE1_N",
"SPI_CE0_N",
"SPI_MISO",
"SPI_MOSI",
"SPI_SCLK",
"NC", /* GPIO12 */
"NC", /* GPIO13 */
/* Serial port */
"TXD0",
"RXD0",
"STATUS_LED_N",
"GPIO17",
"GPIO18",
"NC", /* GPIO19 */
"NC", /* GPIO20 */
"CAM_GPIO",
"GPIO22",
"GPIO23",
"GPIO24",
"GPIO25",
"NC", /* GPIO26 */
"GPIO27",
"GPIO28",
"GPIO29",
"GPIO30",
"GPIO31",
"NC", /* GPIO32 */
"NC", /* GPIO33 */
"NC", /* GPIO34 */
"NC", /* GPIO35 */
"NC", /* GPIO36 */
"NC", /* GPIO37 */
"NC", /* GPIO38 */
"NC", /* GPIO39 */
"PWM0_OUT",
"NC", /* GPIO41 */
"NC", /* GPIO42 */
"NC", /* GPIO43 */
"NC", /* GPIO44 */
"PWM1_OUT",
"HDMI_HPD_P",
"SD_CARD_DET",
/* Used by SD Card */
"SD_CLK_R",
"SD_CMD_R",
"SD_DATA0_R",
"SD_DATA1_R",
"SD_DATA2_R",
"SD_DATA3_R";
pinctrl-0 = <&gpioout &alt0 &i2s_alt2>;
/* I2S interface */
i2s_alt2: i2s_alt2 {

69
arch/arm/boot/dts/bcm2835-rpi-b.dts
View file

@ -16,7 +16,74 @@
};
&gpio {
pinctrl-0 = <&gpioout &alt0 &alt3>;
/*
* Taken from Raspberry-Pi-Rev-1.0-Model-AB-Schematics.pdf
* RPI00021 sheet 02
*
* Legend:
* "NC" = not connected (no rail from the SoC)
* "FOO" = GPIO line named "FOO" on the schematic
* "FOO_N" = GPIO line named "FOO" on schematic, active low
*/
gpio-line-names = "SDA0",
"SCL0",
"SDA1",
"SCL1",
"GPIO_GCLK",
"CAM_CLK",
"LAN_RUN",
"SPI_CE1_N",
"SPI_CE0_N",
"SPI_MISO",
"SPI_MOSI",
"SPI_SCLK",
"NC", /* GPIO12 */
"NC", /* GPIO13 */
/* Serial port */
"TXD0",
"RXD0",
"STATUS_LED_N",
"GPIO17",
"GPIO18",
"NC", /* GPIO19 */
"NC", /* GPIO20 */
"GPIO21",
"GPIO22",
"GPIO23",
"GPIO24",
"GPIO25",
"NC", /* GPIO26 */
"CAM_GPIO",
/* Binary number representing build/revision */
"CONFIG0",
"CONFIG1",
"CONFIG2",
"CONFIG3",
"NC", /* GPIO32 */
"NC", /* GPIO33 */
"NC", /* GPIO34 */
"NC", /* GPIO35 */
"NC", /* GPIO36 */
"NC", /* GPIO37 */
"NC", /* GPIO38 */
"NC", /* GPIO39 */
"PWM0_OUT",
"NC", /* GPIO41 */
"NC", /* GPIO42 */
"NC", /* GPIO43 */
"NC", /* GPIO44 */
"PWM1_OUT",
"HDMI_HPD_P",
"SD_CARD_DET",
/* Used by SD Card */
"SD_CLK_R",
"SD_CMD_R",
"SD_DATA0_R",
"SD_DATA1_R",
"SD_DATA2_R",
"SD_DATA3_R";
pinctrl-0 = <&gpioout &alt0>;
};
&hdmi {

2
arch/arm/boot/dts/bcm2835-rpi-zero.dts
View file

@ -26,7 +26,7 @@
};
&gpio {
pinctrl-0 = <&gpioout &alt0 &i2s_alt0 &alt3>;
pinctrl-0 = <&gpioout &alt0 &i2s_alt0>;
/* I2S interface */
i2s_alt0: i2s_alt0 {

15
arch/arm/boot/dts/bcm2835-rpi.dtsi
View file

@ -39,22 +39,21 @@
};
alt0: alt0 {
brcm,pins = <0 1 2 3 4 5 7 8 9 10 11 14 15 40 45>;
brcm,pins = <4 5 7 8 9 10 11 14 15>;
brcm,function = <BCM2835_FSEL_ALT0>;
};
alt3: alt3 {
brcm,pins = <48 49 50 51 52 53>;
brcm,function = <BCM2835_FSEL_ALT3>;
};
};
&i2c0 {
pinctrl-names = "default";
pinctrl-0 = <&i2c0_gpio0>;
status = "okay";
clock-frequency = <100000>;
};
&i2c1 {
pinctrl-names = "default";
pinctrl-0 = <&i2c1_gpio2>;
status = "okay";
clock-frequency = <100000>;
};
@ -64,11 +63,15 @@
};
&sdhci {
pinctrl-names = "default";
pinctrl-0 = <&emmc_gpio48>;
status = "okay";
bus-width = <4>;
};
&pwm {
pinctrl-names = "default";
pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>;
status = "okay";
};

6
arch/arm/boot/dts/bcm2835.dtsi
View file

@ -23,3 +23,9 @@
};
};
};
/* enable thermal sensor with the correct compatible property set */
&thermal {
compatible = "brcm,bcm2835-thermal";
status = "okay";
};

2
arch/arm/boot/dts/bcm2836-rpi-2-b.dts
View file

@ -27,7 +27,7 @@
};
&gpio {
pinctrl-0 = <&gpioout &alt0 &i2s_alt0 &alt3>;
pinctrl-0 = <&gpioout &alt0 &i2s_alt0>;
/* I2S interface */
i2s_alt0: i2s_alt0 {

6
arch/arm/boot/dts/bcm2836.dtsi
View file

@ -76,3 +76,9 @@
interrupt-parent = <&local_intc>;
interrupts = <8>;
};
/* enable thermal sensor with the correct compatible property set */
&thermal {
compatible = "brcm,bcm2836-thermal";
status = "okay";
};

212
arch/arm/boot/dts/bcm283x.dtsi
View file

@ -104,7 +104,7 @@
reg = <0x7e104000 0x10>;
};
mailbox: mailbox@7e00b800 {
mailbox: mailbox@7e00b880 {
compatible = "brcm,bcm2835-mbox";
reg = <0x7e00b880 0x40>;
interrupts = <0 1>;
@ -132,6 +132,209 @@
interrupt-controller;
#interrupt-cells = <2>;
/* Defines pin muxing groups according to
* BCM2835-ARM-Peripherals.pdf page 102.
*
* While each pin can have its mux selected
* for various functions individually, some
* groups only make sense to switch to a
* particular function together.
*/
dpi_gpio0: dpi_gpio0 {
brcm,pins = <0 1 2 3 4 5 6 7 8 9 10 11
12 13 14 15 16 17 18 19
20 21 22 23 24 25 26 27>;
brcm,function = <BCM2835_FSEL_ALT2>;
};
emmc_gpio22: emmc_gpio22 {
brcm,pins = <22 23 24 25 26 27>;
brcm,function = <BCM2835_FSEL_ALT3>;
};
emmc_gpio34: emmc_gpio34 {
brcm,pins = <34 35 36 37 38 39>;
brcm,function = <BCM2835_FSEL_ALT3>;
brcm,pull = <BCM2835_PUD_OFF
BCM2835_PUD_UP
BCM2835_PUD_UP
BCM2835_PUD_UP
BCM2835_PUD_UP
BCM2835_PUD_UP>;
};
emmc_gpio48: emmc_gpio48 {
brcm,pins = <48 49 50 51 52 53>;
brcm,function = <BCM2835_FSEL_ALT3>;
};
gpclk0_gpio4: gpclk0_gpio4 {
brcm,pins = <4>;
brcm,function = <BCM2835_FSEL_ALT0>;
};
gpclk1_gpio5: gpclk1_gpio5 {
brcm,pins = <5>;
brcm,function = <BCM2835_FSEL_ALT0>;
};
gpclk1_gpio42: gpclk1_gpio42 {
brcm,pins = <42>;
brcm,function = <BCM2835_FSEL_ALT0>;
};
gpclk1_gpio44: gpclk1_gpio44 {
brcm,pins = <44>;
brcm,function = <BCM2835_FSEL_ALT0>;
};
gpclk2_gpio6: gpclk2_gpio6 {
brcm,pins = <6>;
brcm,function = <BCM2835_FSEL_ALT0>;
};
gpclk2_gpio43: gpclk2_gpio43 {
brcm,pins = <43>;
brcm,function = <BCM2835_FSEL_ALT0>;
};
i2c0_gpio0: i2c0_gpio0 {
brcm,pins = <0 1>;
brcm,function = <BCM2835_FSEL_ALT0>;
};
i2c0_gpio32: i2c0_gpio32 {
brcm,pins = <32 34>;
brcm,function = <BCM2835_FSEL_ALT0>;
};
i2c0_gpio44: i2c0_gpio44 {
brcm,pins = <44 45>;
brcm,function = <BCM2835_FSEL_ALT1>;
};
i2c1_gpio2: i2c1_gpio2 {
brcm,pins = <2 3>;
brcm,function = <BCM2835_FSEL_ALT0>;
};
i2c1_gpio44: i2c1_gpio44 {
brcm,pins = <44 45>;
brcm,function = <BCM2835_FSEL_ALT2>;
};
i2c_slave_gpio18: i2c_slave_gpio18 {
brcm,pins = <18 19 20 21>;
brcm,function = <BCM2835_FSEL_ALT3>;
};
jtag_gpio4: jtag_gpio4 {
brcm,pins = <4 5 6 12 13>;
brcm,function = <BCM2835_FSEL_ALT4>;
};
jtag_gpio22: jtag_gpio22 {
brcm,pins = <22 23 24 25 26 27>;
brcm,function = <BCM2835_FSEL_ALT4>;
};
pcm_gpio18: pcm_gpio18 {
brcm,pins = <18 19 20 21>;
brcm,function = <BCM2835_FSEL_ALT0>;
};
pcm_gpio28: pcm_gpio28 {
brcm,pins = <28 29 30 31>;
brcm,function = <BCM2835_FSEL_ALT2>;
};
pwm0_gpio12: pwm0_gpio12 {
brcm,pins = <12>;
brcm,function = <BCM2835_FSEL_ALT0>;
};
pwm0_gpio18: pwm0_gpio18 {
brcm,pins = <18>;
brcm,function = <BCM2835_FSEL_ALT5>;
};
pwm0_gpio40: pwm0_gpio40 {
brcm,pins = <40>;
brcm,function = <BCM2835_FSEL_ALT0>;
};
pwm1_gpio13: pwm1_gpio13 {
brcm,pins = <13>;
brcm,function = <BCM2835_FSEL_ALT0>;
};
pwm1_gpio19: pwm1_gpio19 {
brcm,pins = <19>;
brcm,function = <BCM2835_FSEL_ALT5>;
};
pwm1_gpio41: pwm1_gpio41 {
brcm,pins = <41>;
brcm,function = <BCM2835_FSEL_ALT0>;
};
pwm1_gpio45: pwm1_gpio45 {
brcm,pins = <45>;
brcm,function = <BCM2835_FSEL_ALT0>;
};
sdhost_gpio48: sdhost_gpio48 {
brcm,pins = <48 49 50 51 52 53>;
brcm,function = <BCM2835_FSEL_ALT0>;
};
spi0_gpio7: spi0_gpio7 {
brcm,pins = <7 8 9 10 11>;
brcm,function = <BCM2835_FSEL_ALT0>;
};
spi0_gpio35: spi0_gpio35 {
brcm,pins = <35 36 37 38 39>;
brcm,function = <BCM2835_FSEL_ALT0>;
};
spi1_gpio16: spi1_gpio16 {
brcm,pins = <16 17 18 19 20 21>;
brcm,function = <BCM2835_FSEL_ALT4>;
};
spi2_gpio40: spi2_gpio40 {
brcm,pins = <40 41 42 43 44 45>;
brcm,function = <BCM2835_FSEL_ALT4>;
};
uart0_gpio14: uart0_gpio14 {
brcm,pins = <14 15>;
brcm,function = <BCM2835_FSEL_ALT0>;
};
/* Separate from the uart0_gpio14 group
* because it conflicts with spi1_gpio16, and
* people often run uart0 on the two pins
* without flow contrl.
*/
uart0_ctsrts_gpio16: uart0_ctsrts_gpio16 {
brcm,pins = <16 17>;
brcm,function = <BCM2835_FSEL_ALT3>;
};
uart0_gpio30: uart0_gpio30 {
brcm,pins = <30 31>;
brcm,function = <BCM2835_FSEL_ALT3>;
};
uart0_ctsrts_gpio32: uart0_ctsrts_gpio32 {
brcm,pins = <32 33>;
brcm,function = <BCM2835_FSEL_ALT3>;
};
uart1_gpio14: uart1_gpio14 {
brcm,pins = <14 15>;
brcm,function = <BCM2835_FSEL_ALT5>;
};
uart1_ctsrts_gpio16: uart1_ctsrts_gpio16 {
brcm,pins = <16 17>;
brcm,function = <BCM2835_FSEL_ALT5>;
};
uart1_gpio32: uart1_gpio32 {
brcm,pins = <32 33>;
brcm,function = <BCM2835_FSEL_ALT5>;
};
uart1_ctsrts_gpio30: uart1_ctsrts_gpio30 {
brcm,pins = <30 31>;
brcm,function = <BCM2835_FSEL_ALT5>;
};
uart1_gpio36: uart1_gpio36 {
brcm,pins = <36 37 38 39>;
brcm,function = <BCM2835_FSEL_ALT2>;
};
uart1_gpio40: uart1_gpio40 {
brcm,pins = <40 41>;
brcm,function = <BCM2835_FSEL_ALT5>;
};
uart1_ctsrts_gpio42: uart1_ctsrts_gpio42 {
brcm,pins = <42 43>;
brcm,function = <BCM2835_FSEL_ALT5>;
};
};
uart0: serial@7e201000 {
@ -187,6 +390,13 @@
interrupts = <2 14>; /* pwa1 */
};
thermal: thermal@7e212000 {
compatible = "brcm,bcm2835-thermal";
reg = <0x7e212000 0x8>;
clocks = <&clocks BCM2835_CLOCK_TSENS>;
status = "disabled";
};
aux: aux@0x7e215000 {
compatible = "brcm,bcm2835-aux";
#clock-cells = <1>;

8
arch/arm64/boot/dts/broadcom/bcm2837-rpi-3-b.dts
View file

@ -2,6 +2,7 @@
#include "bcm2837.dtsi"
#include "bcm2835-rpi.dtsi"
#include "bcm283x-rpi-smsc9514.dtsi"
#include "bcm283x-rpi-usb-host.dtsi"
/ {
compatible = "raspberrypi,3-model-b", "brcm,bcm2837";
@ -15,13 +16,6 @@
act {
gpios = <&gpio 47 0>;
};
pwr {
label = "PWR";
gpios = <&gpio 35 0>;
default-state = "keep";
linux,default-trigger = "default-on";
};
};
};

8
arch/arm64/boot/dts/broadcom/bcm2837.dtsi
View file

@ -1,7 +1,7 @@
#include "bcm283x.dtsi"
/ {
compatible = "brcm,bcm2836";
compatible = "brcm,bcm2837";
soc {
ranges = <0x7e000000 0x3f000000 0x1000000>,
@ -74,3 +74,9 @@
interrupt-parent = <&local_intc>;
interrupts = <8>;
};
/* enable thermal sensor with the correct compatible property set */
&thermal {
compatible = "brcm,bcm2837-thermal";
status = "okay";
};

1
arch/arm64/boot/dts/broadcom/bcm283x-rpi-usb-host.dtsi Symbolic link
View file

@ -0,0 +1 @@
../../../../arm/boot/dts/bcm283x-rpi-usb-host.dtsi

38
arch/arm64/boot/dts/broadcom/ns2-svk.dts
View file

@ -157,6 +157,10 @@
status = "ok";
};
&sdio1 {
status = "ok";
};
&nand {
nandcs@0 {
compatible = "brcm,nandcs";
@ -187,3 +191,37 @@
groups = "nand_grp";
};
};
&qspi {
bspi-sel = <0>;
flash: m25p80@0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "m25p80";
reg = <0x0>;
spi-max-frequency = <12500000>;
m25p,fast-read;
spi-cpol;
spi-cpha;
partition@0 {
label = "boot";
reg = <0x00000000 0x000a0000>;
};
partition@a0000 {
label = "env";
reg = <0x000a0000 0x00060000>;
};
partition@100000 {
label = "system";
reg = <0x00100000 0x00600000>;
};
partition@700000 {
label = "rootfs";
reg = <0x00700000 0x01900000>;
};
};
};

62
arch/arm64/boot/dts/broadcom/ns2.dtsi
View file

@ -133,6 +133,9 @@
status = "disabled";
phys = <&pci_phy0>;
phy-names = "pcie-phy";
msi-parent = <&msi0>;
msi0: msi@20020000 {
compatible = "brcm,iproc-msi";
@ -171,6 +174,9 @@
status = "disabled";
phys = <&pci_phy1>;
phy-names = "pcie-phy";
msi-parent = <&msi4>;
msi4: msi@50020000 {
compatible = "brcm,iproc-msi";
@ -191,6 +197,42 @@
#include "ns2-clock.dtsi"
pdc0: iproc-pdc0@612c0000 {
compatible = "brcm,iproc-pdc-mbox";
reg = <0x612c0000 0x445>; /* PDC FS0 regs */
interrupts = <GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>;
#mbox-cells = <1>;
brcm,rx-status-len = <32>;
brcm,use-bcm-hdr;
};
pdc1: iproc-pdc1@612e0000 {
compatible = "brcm,iproc-pdc-mbox";
reg = <0x612e0000 0x445>; /* PDC FS1 regs */
interrupts = <GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>;
#mbox-cells = <1>;
brcm,rx-status-len = <32>;
brcm,use-bcm-hdr;
};
pdc2: iproc-pdc2@61300000 {
compatible = "brcm,iproc-pdc-mbox";
reg = <0x61300000 0x445>; /* PDC FS2 regs */
interrupts = <GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>;
#mbox-cells = <1>;
brcm,rx-status-len = <32>;
brcm,use-bcm-hdr;
};
pdc3: iproc-pdc3@61320000 {
compatible = "brcm,iproc-pdc-mbox";
reg = <0x61320000 0x445>; /* PDC FS3 regs */
interrupts = <GIC_SPI 193 IRQ_TYPE_LEVEL_HIGH>;
#mbox-cells = <1>;
brcm,rx-status-len = <32>;
brcm,use-bcm-hdr;
};
dma0: dma@61360000 {
compatible = "arm,pl330", "arm,primecell";
reg = <0x61360000 0x1000>;
@ -248,7 +290,7 @@
<GIC_SPI 260 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 261 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 262 IRQ_TYPE_LEVEL_HIGH>;
mmu-masters;
#iommu-cells = <1>;
};
pinctrl: pinctrl@6501d130 {
@ -565,5 +607,23 @@
brcm,nand-has-wp;
};
qspi: spi@66470200 {
compatible = "brcm,spi-bcm-qspi", "brcm,spi-ns2-qspi";
reg = <0x66470200 0x184>,
<0x66470000 0x124>,
<0x67017408 0x004>,
<0x664703a0 0x01c>;
reg-names = "mspi", "bspi", "intr_regs",
"intr_status_reg";
interrupts = <GIC_SPI 419 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "spi_l1_intr";
clocks = <&iprocmed>;
clock-names = "iprocmed";
num-cs = <2>;
#address-cells = <1>;
#size-cells = <0>;
};
};
};

6
drivers/pinctrl/bcm/pinctrl-bcm2835.c
View file

@ -76,12 +76,6 @@ enum bcm2835_pinconf_param {
BCM2835_PINCONF_PARAM_PULL,
};
enum bcm2835_pinconf_pull {
BCM2835_PINCONFIG_PULL_NONE,
BCM2835_PINCONFIG_PULL_DOWN,
BCM2835_PINCONFIG_PULL_UP,
};
#define BCM2835_PINCONF_PACK(_param_, _arg_) ((_param_) << 16 | (_arg_))
#define BCM2835_PINCONF_UNPACK_PARAM(_conf_) ((_conf_) >> 16)
#define BCM2835_PINCONF_UNPACK_ARG(_conf_) ((_conf_) & 0xffff)

5
include/dt-bindings/pinctrl/bcm2835.h
View file

@ -24,4 +24,9 @@
#define BCM2835_FSEL_ALT2 6
#define BCM2835_FSEL_ALT3 7
/* brcm,pull property */
#define BCM2835_PUD_OFF 0
#define BCM2835_PUD_DOWN 1
#define BCM2835_PUD_UP 2
#endif /* __DT_BINDINGS_PINCTRL_BCM2835_H__ */