redonkable
/
remarkable-linux
1
0
Fork 0
Code Releases Activity

ARM: dts: Ux500: fix up TVK sensor data 

- Fix the I2C address and supply line names for the AK8974

- Sets up the interrupt lines to the different components as they
  actually are connected, I was confused for some time by the fact
  that several lines were connected with <NM> 0 Ohm resistors, which
  means NOT MOUNTED and is thus not 0 Ohm at all but infinite ohms,
  i.e. not connected at all.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
steinar/wifi_calib_4_9_kernel
Linus Walleij 2016-07-04 15:10:57 +02:00 committed by Arnd Bergmann
parent b9ab9dcd0d
commit 83919ef0a5
1 changed files with 43 additions and 19 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

62
arch/arm/boot/dts/ste-href-tvk1281618.dtsi
View File

@ -99,46 +99,69 @@
vddio-supply = <&db8500_vsmps2_reg>;
pinctrl-names = "default";
pinctrl-0 = <&accel_tvk_mode>;
interrupt-parent = <&gpio2>;
interrupts = <18 IRQ_TYPE_EDGE_FALLING>,
<19 IRQ_TYPE_EDGE_FALLING>;
/*
* These interrupts cannot be used: the other component
* ST-Micro L3D4200D gyro that is connected to the same lines
* cannot set its DRDY line to open drain, so it cannot be
* shared with other peripherals. The should be defined for
* the falling edge if they could be wired together.
*
* interrupts-extended =
* <&gpio1 0 IRQ_TYPE_EDGE_FALLING>,
* <&gpio2 19 IRQ_TYPE_EDGE_FALLING>;
*/
};
lsm303dlh@1e {
/*
* This magnetometer is packaged with
* the accelerometer, and has a DRDY line,
* however it is not connected on this
* board so it can not generate interrupts.
*/
/* Magnetometer */
compatible = "st,lsm303dlh-magn";
reg = <0x1e>;
vdd-supply = <&ab8500_ldo_aux1_reg>;
vddio-supply = <&db8500_vsmps2_reg>;
/*
* These interrupts cannot be used: the other component
* ST-Micro L3D4200D gyro that is connected to the same lines
* cannot set its DRDY line to open drain, so it cannot be
* shared with other peripherals. The should be defined for
* the falling edge if they could be wired together.
*
* interrupts-extended =
* <&gpio1 0 IRQ_TYPE_EDGE_FALLING>,
* <&gpio2 19 IRQ_TYPE_EDGE_FALLING>;
*/
};
lis331dl@1c {
/* Accelerometer */
compatible = "st,lis331dl-accel";
st,drdy-int-pin = <1>;
drive-open-drain;
reg = <0x1c>;
vdd-supply = <&ab8500_ldo_aux1_reg>;
vddio-supply = <&db8500_vsmps2_reg>;
pinctrl-names = "default";
pinctrl-0 = <&accel_tvk_mode>;
interrupt-parent = <&gpio2>;
interrupts = <18 IRQ_TYPE_EDGE_FALLING>,
<19 IRQ_TYPE_EDGE_FALLING>;
/* INT2 would need to be open drain */
interrupts = <18 IRQ_TYPE_EDGE_RISING>,
<19 IRQ_TYPE_EDGE_RISING>;
};
ak8974@0f {
/* Magnetometer */
compatible = "asahi-kasei,ak8974";
reg = <0x0f>;
vdd-supply = <&ab8500_ldo_aux1_reg>;
vddio-supply = <&db8500_vsmps2_reg>;
avdd-supply = <&ab8500_ldo_aux1_reg>;
dvdd-supply = <&db8500_vsmps2_reg>;
pinctrl-names = "default";
pinctrl-0 = <&gyro_magn_tvk_mode>;
interrupt-parent = <&gpio1>;
interrupts = <0 IRQ_TYPE_EDGE_RISING>;
/*
* These interrupts cannot be used: the other component
* ST-Micro L3D4200D gyro that is connected to the same lines
* cannot set its DRDY line to open drain, so it cannot be
* shared with other peripherals. The should be defined for
* the falling edge if they could be wired together.
*
* interrupts-extended =
* <&gpio1 0 IRQ_TYPE_EDGE_FALLING>,
* <&gpio0 31 IRQ_TYPE_EDGE_FALLING>;
*/
};
l3g4200d@68 {
/* Gyroscope */
@ -149,8 +172,9 @@
vddio-supply = <&db8500_vsmps2_reg>;
pinctrl-names = "default";
pinctrl-0 = <&gyro_magn_tvk_mode>;
interrupt-parent = <&gpio1>;
interrupts = <0 IRQ_TYPE_EDGE_RISING>;
interrupts-extended =
<&gpio1 0 IRQ_TYPE_EDGE_RISING>,
<&gpio0 31 IRQ_TYPE_EDGE_RISING>;
};
lsp001wm@5c {
/* Barometer/pressure sensor */
@ -218,7 +242,7 @@
/* Accelerometer interrupt lines 1 & 2 */
tvk_cfg {
pins = "GPIO82_C1", "GPIO83_D3";
ste,config = <&gpio_in_pu>;
ste,config = <&gpio_in_pd>;
};
};
};