hwmon: (pmbus) Add client driver for LTC3815
LTC3815 is a Monolithic Synchronous DC/DC Step-Down Converter. Cc: Michael Jones <mike@proclivis.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net>steinar/wifi_calib_4_9_kernel
Guenter Roeck
parent
2ff44072e3
commit
8d28cd1b1f
|
|
@ -0,0 +1,61 @@
|
|||
Kernel driver ltc3815
|
||||
=====================
|
||||
|
||||
Supported chips:
|
||||
* Linear Technology LTC3815
|
||||
Prefix: 'ltc3815'
|
||||
Addresses scanned: -
|
||||
Datasheet: http://www.linear.com/product/ltc3815
|
||||
|
||||
Author: Guenter Roeck <linux@roeck-us.net>
|
||||
|
||||
|
||||
Description
|
||||
-----------
|
||||
|
||||
LTC3815 is a Monolithic Synchronous DC/DC Step-Down Converter.
|
||||
|
||||
|
||||
Usage Notes
|
||||
-----------
|
||||
|
||||
This driver does not probe for PMBus devices. You will have to instantiate
|
||||
devices explicitly.
|
||||
|
||||
Example: the following commands will load the driver for an LTC3815
|
||||
at address 0x20 on I2C bus #1:
|
||||
|
||||
# modprobe ltc3815
|
||||
# echo ltc3815 0x20 > /sys/bus/i2c/devices/i2c-1/new_device
|
||||
|
||||
|
||||
Sysfs attributes
|
||||
----------------
|
||||
|
||||
in1_label "vin"
|
||||
in1_input Measured input voltage.
|
||||
in1_alarm Input voltage alarm.
|
||||
in1_highest Highest input voltage.
|
||||
in1_reset_history Reset input voltage history.
|
||||
|
||||
in2_label "vout1".
|
||||
in2_input Measured output voltage.
|
||||
in2_alarm Output voltage alarm.
|
||||
in2_highest Highest output voltage.
|
||||
in2_reset_history Reset output voltage history.
|
||||
|
||||
temp1_input Measured chip temperature.
|
||||
temp1_alarm Temperature alarm.
|
||||
temp1_highest Highest measured temperature.
|
||||
temp1_reset_history Reset temperature history.
|
||||
|
||||
curr1_label "iin".
|
||||
curr1_input Measured input current.
|
||||
curr1_highest Highest input current.
|
||||
curr1_reset_history Reset input current history.
|
||||
|
||||
curr2_label "iout1".
|
||||
curr2_input Measured output current.
|
||||
curr2_alarm Output current alarm.
|
||||
curr2_highest Highest output current.
|
||||
curr2_reset_history Reset output current history.
|
||||
|
|
@ -65,6 +65,16 @@ config SENSORS_LTC2978_REGULATOR
|
|||
If you say yes here you get regulator support for Linear
|
||||
Technology LTC2974, LTC2977, LTC2978, LTC3880, LTC3883, and LTM4676.
|
||||
|
||||
config SENSORS_LTC3815
|
||||
tristate "Linear Technologies LTC3815"
|
||||
default n
|
||||
help
|
||||
If you say yes here you get hardware monitoring support for Linear
|
||||
Technology LTC3815.
|
||||
|
||||
This driver can also be built as a module. If so, the module will
|
||||
be called ltc3815.
|
||||
|
||||
config SENSORS_MAX16064
|
||||
tristate "Maxim MAX16064"
|
||||
default n
|
||||
|
|
|
|||
|
|
@ -7,6 +7,7 @@ obj-$(CONFIG_SENSORS_PMBUS) += pmbus.o
|
|||
obj-$(CONFIG_SENSORS_ADM1275) += adm1275.o
|
||||
obj-$(CONFIG_SENSORS_LM25066) += lm25066.o
|
||||
obj-$(CONFIG_SENSORS_LTC2978) += ltc2978.o
|
||||
obj-$(CONFIG_SENSORS_LTC3815) += ltc3815.o
|
||||
obj-$(CONFIG_SENSORS_MAX16064) += max16064.o
|
||||
obj-$(CONFIG_SENSORS_MAX20751) += max20751.o
|
||||
obj-$(CONFIG_SENSORS_MAX34440) += max34440.o
|
||||
|
|
|
|||
|
|
@ -0,0 +1,215 @@
|
|||
/*
|
||||
* Hardware monitoring driver for LTC3815
|
||||
*
|
||||
* Copyright (c) 2015 Linear Technology
|
||||
* Copyright (c) 2015 Guenter Roeck
|
||||
*
|
||||
* This program is free software; you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License as published by
|
||||
* the Free Software Foundation; either version 2 of the License, or
|
||||
* (at your option) any later version.
|
||||
*
|
||||
* This program is distributed in the hope that it will be useful,
|
||||
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
* GNU General Public License for more details.
|
||||
*/
|
||||
|
||||
#include <linux/err.h>
|
||||
#include <linux/i2c.h>
|
||||
#include <linux/init.h>
|
||||
#include <linux/jiffies.h>
|
||||
#include <linux/kernel.h>
|
||||
#include <linux/module.h>
|
||||
#include "pmbus.h"
|
||||
|
||||
#define LTC3815_MFR_IOUT_PEAK 0xd7
|
||||
#define LTC3815_MFR_VOUT_PEAK 0xdd
|
||||
#define LTC3815_MFR_VIN_PEAK 0xde
|
||||
#define LTC3815_MFR_TEMP_PEAK 0xdf
|
||||
#define LTC3815_MFR_IIN_PEAK 0xe1
|
||||
#define LTC3815_MFR_SPECIAL_ID 0xe7
|
||||
|
||||
#define LTC3815_ID 0x8000
|
||||
#define LTC3815_ID_MASK 0xff00
|
||||
|
||||
static int ltc3815_read_byte_data(struct i2c_client *client, int page, int reg)
|
||||
{
|
||||
int ret;
|
||||
|
||||
switch (reg) {
|
||||
case PMBUS_VOUT_MODE:
|
||||
/*
|
||||
* The chip returns 0x3e, suggesting VID mode with manufacturer
|
||||
* specific VID codes. Since the output voltage is reported
|
||||
* with a LSB of 0.5mV, override and report direct mode with
|
||||
* appropriate coefficients.
|
||||
*/
|
||||
ret = 0x40;
|
||||
break;
|
||||
default:
|
||||
ret = -ENODATA;
|
||||
break;
|
||||
}
|
||||
return ret;
|
||||
}
|
||||
|
||||
static int ltc3815_write_byte(struct i2c_client *client, int page, u8 reg)
|
||||
{
|
||||
int ret;
|
||||
|
||||
switch (reg) {
|
||||
case PMBUS_CLEAR_FAULTS:
|
||||
/*
|
||||
* LTC3815 does not support the CLEAR_FAULTS command.
|
||||
* Emulate it by clearing the status register.
|
||||
*/
|
||||
ret = pmbus_read_word_data(client, 0, PMBUS_STATUS_WORD);
|
||||
if (ret > 0) {
|
||||
pmbus_write_word_data(client, 0, PMBUS_STATUS_WORD,
|
||||
ret);
|
||||
ret = 0;
|
||||
}
|
||||
break;
|
||||
default:
|
||||
ret = -ENODATA;
|
||||
break;
|
||||
}
|
||||
return ret;
|
||||
}
|
||||
|
||||
static int ltc3815_read_word_data(struct i2c_client *client, int page, int reg)
|
||||
{
|
||||
int ret;
|
||||
|
||||
switch (reg) {
|
||||
case PMBUS_VIRT_READ_VIN_MAX:
|
||||
ret = pmbus_read_word_data(client, page, LTC3815_MFR_VIN_PEAK);
|
||||
break;
|
||||
case PMBUS_VIRT_READ_VOUT_MAX:
|
||||
ret = pmbus_read_word_data(client, page, LTC3815_MFR_VOUT_PEAK);
|
||||
break;
|
||||
case PMBUS_VIRT_READ_TEMP_MAX:
|
||||
ret = pmbus_read_word_data(client, page, LTC3815_MFR_TEMP_PEAK);
|
||||
break;
|
||||
case PMBUS_VIRT_READ_IOUT_MAX:
|
||||
ret = pmbus_read_word_data(client, page, LTC3815_MFR_IOUT_PEAK);
|
||||
break;
|
||||
case PMBUS_VIRT_READ_IIN_MAX:
|
||||
ret = pmbus_read_word_data(client, page, LTC3815_MFR_IIN_PEAK);
|
||||
break;
|
||||
case PMBUS_VIRT_RESET_VOUT_HISTORY:
|
||||
case PMBUS_VIRT_RESET_VIN_HISTORY:
|
||||
case PMBUS_VIRT_RESET_TEMP_HISTORY:
|
||||
case PMBUS_VIRT_RESET_IOUT_HISTORY:
|
||||
case PMBUS_VIRT_RESET_IIN_HISTORY:
|
||||
ret = 0;
|
||||
break;
|
||||
default:
|
||||
ret = -ENODATA;
|
||||
break;
|
||||
}
|
||||
return ret;
|
||||
}
|
||||
|
||||
static int ltc3815_write_word_data(struct i2c_client *client, int page,
|
||||
int reg, u16 word)
|
||||
{
|
||||
int ret;
|
||||
|
||||
switch (reg) {
|
||||
case PMBUS_VIRT_RESET_IIN_HISTORY:
|
||||
ret = pmbus_write_word_data(client, page,
|
||||
LTC3815_MFR_IIN_PEAK, 0);
|
||||
break;
|
||||
case PMBUS_VIRT_RESET_IOUT_HISTORY:
|
||||
ret = pmbus_write_word_data(client, page,
|
||||
LTC3815_MFR_IOUT_PEAK, 0);
|
||||
break;
|
||||
case PMBUS_VIRT_RESET_VOUT_HISTORY:
|
||||
ret = pmbus_write_word_data(client, page,
|
||||
LTC3815_MFR_VOUT_PEAK, 0);
|
||||
break;
|
||||
case PMBUS_VIRT_RESET_VIN_HISTORY:
|
||||
ret = pmbus_write_word_data(client, page,
|
||||
LTC3815_MFR_VIN_PEAK, 0);
|
||||
break;
|
||||
case PMBUS_VIRT_RESET_TEMP_HISTORY:
|
||||
ret = pmbus_write_word_data(client, page,
|
||||
LTC3815_MFR_TEMP_PEAK, 0);
|
||||
break;
|
||||
default:
|
||||
ret = -ENODATA;
|
||||
break;
|
||||
}
|
||||
return ret;
|
||||
}
|
||||
|
||||
static const struct i2c_device_id ltc3815_id[] = {
|
||||
{"ltc3815", 0},
|
||||
{ }
|
||||
};
|
||||
MODULE_DEVICE_TABLE(i2c, ltc3815_id);
|
||||
|
||||
static struct pmbus_driver_info ltc3815_info = {
|
||||
.pages = 1,
|
||||
.format[PSC_VOLTAGE_IN] = direct,
|
||||
.format[PSC_VOLTAGE_OUT] = direct,
|
||||
.format[PSC_CURRENT_IN] = direct,
|
||||
.format[PSC_CURRENT_OUT] = direct,
|
||||
.format[PSC_TEMPERATURE] = direct,
|
||||
.m[PSC_VOLTAGE_IN] = 250,
|
||||
.b[PSC_VOLTAGE_IN] = 0,
|
||||
.R[PSC_VOLTAGE_IN] = 0,
|
||||
.m[PSC_VOLTAGE_OUT] = 2,
|
||||
.b[PSC_VOLTAGE_OUT] = 0,
|
||||
.R[PSC_VOLTAGE_OUT] = 3,
|
||||
.m[PSC_CURRENT_IN] = 1,
|
||||
.b[PSC_CURRENT_IN] = 0,
|
||||
.R[PSC_CURRENT_IN] = 2,
|
||||
.m[PSC_CURRENT_OUT] = 1,
|
||||
.b[PSC_CURRENT_OUT] = 0,
|
||||
.R[PSC_CURRENT_OUT] = 2,
|
||||
.m[PSC_TEMPERATURE] = 1,
|
||||
.b[PSC_TEMPERATURE] = 0,
|
||||
.R[PSC_TEMPERATURE] = 0,
|
||||
.func[0] = PMBUS_HAVE_VIN | PMBUS_HAVE_IIN | PMBUS_HAVE_VOUT |
|
||||
PMBUS_HAVE_IOUT | PMBUS_HAVE_TEMP,
|
||||
.read_byte_data = ltc3815_read_byte_data,
|
||||
.read_word_data = ltc3815_read_word_data,
|
||||
.write_byte = ltc3815_write_byte,
|
||||
.write_word_data = ltc3815_write_word_data,
|
||||
};
|
||||
|
||||
static int ltc3815_probe(struct i2c_client *client,
|
||||
const struct i2c_device_id *id)
|
||||
{
|
||||
int chip_id;
|
||||
|
||||
if (!i2c_check_functionality(client->adapter,
|
||||
I2C_FUNC_SMBUS_READ_WORD_DATA))
|
||||
return -ENODEV;
|
||||
|
||||
chip_id = i2c_smbus_read_word_data(client, LTC3815_MFR_SPECIAL_ID);
|
||||
if (chip_id < 0)
|
||||
return chip_id;
|
||||
if ((chip_id & LTC3815_ID_MASK) != LTC3815_ID)
|
||||
return -ENODEV;
|
||||
|
||||
return pmbus_do_probe(client, id, <c3815_info);
|
||||
}
|
||||
|
||||
static struct i2c_driver ltc3815_driver = {
|
||||
.driver = {
|
||||
.name = "ltc3815",
|
||||
},
|
||||
.probe = ltc3815_probe,
|
||||
.remove = pmbus_do_remove,
|
||||
.id_table = ltc3815_id,
|
||||
};
|
||||
|
||||
module_i2c_driver(ltc3815_driver);
|
||||
|
||||
MODULE_AUTHOR("Guenter Roeck");
|
||||
MODULE_DESCRIPTION("PMBus driver for LTC3815");
|
||||
MODULE_LICENSE("GPL");
|
||||
Loading…
Reference in New Issue