redonkable
/
remarkable-linux
1
0
Fork 0
Code Releases Activity

mtd: nand: davinci: extend description of bindings 

Extend bindings for davinci_nand driver to be more clear.
This is clarification only, without semantic changes.

Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Taras Kondratiuk <taras@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
wifi-calibration
Ivan Khoronzhuk 2013-12-17 15:37:37 +02:00 committed by Brian Norris
parent c354ae4351
commit 9ba51cff55
1 changed files with 53 additions and 22 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

75
Documentation/devicetree/bindings/mtd/davinci-nand.txt
View File

@ -1,36 +1,67 @@
* Texas Instruments Davinci NAND
Device tree bindings for Texas instruments Davinci NAND controller
This file provides information, what the device node for the
davinci nand interface contain.
This file provides information, what the device node for the davinci NAND
interface contains.
Documentation:
Davinci DM646x - http://www.ti.com/lit/ug/sprueq7c/sprueq7c.pdf
Required properties:
- compatible: "ti,davinci-nand";
- reg : contain 2 offset/length values:
- offset and length for the access window
- offset and length for accessing the aemif control registers
- ti,davinci-chipselect: Indicates on the davinci_nand driver which
chipselect is used for accessing the nand.
- compatible: "ti,davinci-nand"
- reg: Contains 2 offset/length values:
- offset and length for the access window.
- offset and length for accessing the AEMIF
control registers.
- ti,davinci-chipselect: number of chipselect. Indicates on the
davinci_nand driver which chipselect is used
for accessing the nand.
Can be in the range [0-3].
Recommended properties :
- ti,davinci-mask-ale: mask for ale
- ti,davinci-mask-cle: mask for cle
- ti,davinci-mask-chipsel: mask for chipselect
- ti,davinci-ecc-mode: ECC mode valid values for davinci driver:
- "none"
- "soft"
- "hw"
- ti,davinci-ecc-bits: used ECC bits, currently supported 1 or 4.
- ti,davinci-nand-buswidth: buswidth 8 or 16
- ti,davinci-nand-use-bbt: use flash based bad block table support.
nand device bindings may contain additional sub-nodes describing
partitions of the address space. See partition.txt for more detail.
- ti,davinci-mask-ale: mask for ALE. Needed for executing address
phase. These offset will be added to the base
address for the chip select space the NAND Flash
device is connected to.
If not set equal to 0x08.
- ti,davinci-mask-cle: mask for CLE. Needed for executing command
phase. These offset will be added to the base
address for the chip select space the NAND Flash
device is connected to.
If not set equal to 0x10.
- ti,davinci-mask-chipsel: mask for chipselect address. Needed to mask
addresses for given chipselect.
- ti,davinci-ecc-mode: operation mode of the NAND ecc mode. ECC mode
valid values for davinci driver:
- "none"
- "soft"
- "hw"
- ti,davinci-ecc-bits: used ECC bits, currently supported 1 or 4.
- ti,davinci-nand-buswidth: buswidth 8 or 16.
- ti,davinci-nand-use-bbt: use flash based bad block table support. OOB
identifier is saved in OOB area.
Nand device bindings may contain additional sub-nodes describing partitions of
the address space. See partition.txt for more detail. The NAND Flash timing
values must be programmed in the chip select’s node of AEMIF
memory-controller (see Documentation/devicetree/bindings/memory-controllers/
davinci-aemif.txt).
Example(da850 EVM ):
nand_cs3@62000000 {
compatible = "ti,davinci-nand";
reg = <0x62000000 0x807ff
0x68000000 0x8000>;
0x68000000 0x8000>;
ti,davinci-chipselect = <1>;
ti,davinci-mask-ale = <0>;
ti,davinci-mask-cle = <0>;