diff --git a/Documentation/devicetree/bindings/thermal/rcar-thermal.txt b/Documentation/devicetree/bindings/thermal/rcar-thermal.txt
index 0ef00be44b01..43404b197933 100644
--- a/Documentation/devicetree/bindings/thermal/rcar-thermal.txt
+++ b/Documentation/devicetree/bindings/thermal/rcar-thermal.txt
@@ -7,7 +7,10 @@ Required properties:
 			    - "renesas,thermal-r8a73a4" (R-Mobile AP6)
 			    - "renesas,thermal-r8a7779" (R-Car H1)
 			    - "renesas,thermal-r8a7790" (R-Car H2)
-			    - "renesas,thermal-r8a7791" (R-Car M2)
+			    - "renesas,thermal-r8a7791" (R-Car M2-W)
+			    - "renesas,thermal-r8a7792" (R-Car V2H)
+			    - "renesas,thermal-r8a7793" (R-Car M2-N)
+			    - "renesas,thermal-r8a7794" (R-Car E2)
 - reg			: Address range of the thermal registers.
 			  The 1st reg will be recognized as common register
 			  if it has "interrupts".
diff --git a/drivers/thermal/of-thermal.c b/drivers/thermal/of-thermal.c
index f8eb625b8400..62143ba31001 100644
--- a/drivers/thermal/of-thermal.c
+++ b/drivers/thermal/of-thermal.c
@@ -387,15 +387,18 @@ thermal_zone_of_sensor_register(struct device *dev, int sensor_id,
 				int (*get_trend)(void *, long *))
 {
 	struct device_node *np, *child, *sensor_np;
+	struct thermal_zone_device *tzd = ERR_PTR(-ENODEV);
 
 	np = of_find_node_by_name(NULL, "thermal-zones");
 	if (!np)
 		return ERR_PTR(-ENODEV);
 
-	if (!dev || !dev->of_node)
+	if (!dev || !dev->of_node) {
+		of_node_put(np);
 		return ERR_PTR(-EINVAL);
+	}
 
-	sensor_np = dev->of_node;
+	sensor_np = of_node_get(dev->of_node);
 
 	for_each_child_of_node(np, child) {
 		struct of_phandle_args sensor_specs;
@@ -422,16 +425,21 @@ thermal_zone_of_sensor_register(struct device *dev, int sensor_id,
 		}
 
 		if (sensor_specs.np == sensor_np && id == sensor_id) {
-			of_node_put(np);
-			return thermal_zone_of_add_sensor(child, sensor_np,
-							  data,
-							  get_temp,
-							  get_trend);
+			tzd = thermal_zone_of_add_sensor(child, sensor_np,
+							 data,
+							 get_temp,
+							 get_trend);
+			of_node_put(sensor_specs.np);
+			of_node_put(child);
+			goto exit;
 		}
+		of_node_put(sensor_specs.np);
 	}
+exit:
+	of_node_put(sensor_np);
 	of_node_put(np);
 
-	return ERR_PTR(-ENODEV);
+	return tzd;
 }
 EXPORT_SYMBOL_GPL(thermal_zone_of_sensor_register);
 
@@ -623,6 +631,7 @@ static int thermal_of_populate_trip(struct device_node *np,
 
 	/* Required for cooling map matching */
 	trip->np = np;
+	of_node_get(np);
 
 	return 0;
 }
@@ -730,9 +739,14 @@ finish:
 	return tz;
 
 free_tbps:
+	for (i = 0; i < tz->num_tbps; i++)
+		of_node_put(tz->tbps[i].cooling_device);
 	kfree(tz->tbps);
 free_trips:
+	for (i = 0; i < tz->ntrips; i++)
+		of_node_put(tz->trips[i].np);
 	kfree(tz->trips);
+	of_node_put(gchild);
 free_tz:
 	kfree(tz);
 	of_node_put(child);
@@ -742,7 +756,13 @@ free_tz:
 
 static inline void of_thermal_free_zone(struct __thermal_zone *tz)
 {
+	int i;
+
+	for (i = 0; i < tz->num_tbps; i++)
+		of_node_put(tz->tbps[i].cooling_device);
 	kfree(tz->tbps);
+	for (i = 0; i < tz->ntrips; i++)
+		of_node_put(tz->trips[i].np);
 	kfree(tz->trips);
 	kfree(tz);
 }
@@ -814,10 +834,13 @@ int __init of_parse_thermal_zones(void)
 			/* attempting to build remaining zones still */
 		}
 	}
+	of_node_put(np);
 
 	return 0;
 
 exit_free:
+	of_node_put(child);
+	of_node_put(np);
 	of_thermal_free_zone(tz);
 
 	/* no memory available, so free what we have built */
@@ -859,4 +882,5 @@ void of_thermal_destroy_zones(void)
 		kfree(zone->ops);
 		of_thermal_free_zone(zone->devdata);
 	}
+	of_node_put(np);
 }
diff --git a/drivers/thermal/samsung/exynos_thermal_common.h b/drivers/thermal/samsung/exynos_thermal_common.h
index 3eb2ed9ea3a4..158f5aa8dc5d 100644
--- a/drivers/thermal/samsung/exynos_thermal_common.h
+++ b/drivers/thermal/samsung/exynos_thermal_common.h
@@ -27,7 +27,7 @@
 #define SENSOR_NAME_LEN	16
 #define MAX_TRIP_COUNT	8
 #define MAX_COOLING_DEVICE 4
-#define MAX_THRESHOLD_LEVS 5
+#define MAX_TRIMINFO_CTRL_REG	2
 
 #define ACTIVE_INTERVAL 500
 #define IDLE_INTERVAL 10000
diff --git a/drivers/thermal/samsung/exynos_tmu.c b/drivers/thermal/samsung/exynos_tmu.c
index acbff14da3a4..49c09243fd38 100644
--- a/drivers/thermal/samsung/exynos_tmu.c
+++ b/drivers/thermal/samsung/exynos_tmu.c
@@ -77,16 +77,6 @@ static int temp_to_code(struct exynos_tmu_data *data, u8 temp)
 	struct exynos_tmu_platform_data *pdata = data->pdata;
 	int temp_code;
 
-	if (pdata->cal_mode == HW_MODE)
-		return temp;
-
-	if (data->soc == SOC_ARCH_EXYNOS4210)
-		/* temp should range between 25 and 125 */
-		if (temp < 25 || temp > 125) {
-			temp_code = -EINVAL;
-			goto out;
-		}
-
 	switch (pdata->cal_type) {
 	case TYPE_TWO_POINT_TRIMMING:
 		temp_code = (temp - pdata->first_point_trim) *
@@ -101,7 +91,7 @@ static int temp_to_code(struct exynos_tmu_data *data, u8 temp)
 		temp_code = temp + pdata->default_temp_offset;
 		break;
 	}
-out:
+
 	return temp_code;
 }
 
@@ -114,16 +104,6 @@ static int code_to_temp(struct exynos_tmu_data *data, u8 temp_code)
 	struct exynos_tmu_platform_data *pdata = data->pdata;
 	int temp;
 
-	if (pdata->cal_mode == HW_MODE)
-		return temp_code;
-
-	if (data->soc == SOC_ARCH_EXYNOS4210)
-		/* temp_code should range between 75 and 175 */
-		if (temp_code < 75 || temp_code > 175) {
-			temp = -ENODATA;
-			goto out;
-		}
-
 	switch (pdata->cal_type) {
 	case TYPE_TWO_POINT_TRIMMING:
 		temp = (temp_code - data->temp_error1) *
@@ -138,18 +118,35 @@ static int code_to_temp(struct exynos_tmu_data *data, u8 temp_code)
 		temp = temp_code - pdata->default_temp_offset;
 		break;
 	}
-out:
+
 	return temp;
 }
 
+static void exynos_tmu_clear_irqs(struct exynos_tmu_data *data)
+{
+	const struct exynos_tmu_registers *reg = data->pdata->registers;
+	unsigned int val_irq;
+
+	val_irq = readl(data->base + reg->tmu_intstat);
+	/*
+	 * Clear the interrupts.  Please note that the documentation for
+	 * Exynos3250, Exynos4412, Exynos5250 and Exynos5260 incorrectly
+	 * states that INTCLEAR register has a different placing of bits
+	 * responsible for FALL IRQs than INTSTAT register.  Exynos5420
+	 * and Exynos5440 documentation is correct (Exynos4210 doesn't
+	 * support FALL IRQs at all).
+	 */
+	writel(val_irq, data->base + reg->tmu_intclear);
+}
+
 static int exynos_tmu_initialize(struct platform_device *pdev)
 {
 	struct exynos_tmu_data *data = platform_get_drvdata(pdev);
 	struct exynos_tmu_platform_data *pdata = data->pdata;
 	const struct exynos_tmu_registers *reg = pdata->registers;
-	unsigned int status, trim_info = 0, con;
+	unsigned int status, trim_info = 0, con, ctrl;
 	unsigned int rising_threshold = 0, falling_threshold = 0;
-	int ret = 0, threshold_code, i, trigger_levs = 0;
+	int ret = 0, threshold_code, i;
 
 	mutex_lock(&data->lock);
 	clk_enable(data->clk);
@@ -164,11 +161,17 @@ static int exynos_tmu_initialize(struct platform_device *pdev)
 		}
 	}
 
-	if (TMU_SUPPORTS(pdata, TRIM_RELOAD))
-		__raw_writel(1, data->base + reg->triminfo_ctrl);
-
-	if (pdata->cal_mode == HW_MODE)
-		goto skip_calib_data;
+	if (TMU_SUPPORTS(pdata, TRIM_RELOAD)) {
+		for (i = 0; i < reg->triminfo_ctrl_count; i++) {
+			if (pdata->triminfo_reload[i]) {
+				ctrl = readl(data->base +
+						reg->triminfo_ctrl[i]);
+				ctrl |= pdata->triminfo_reload[i];
+				writel(ctrl, data->base +
+						reg->triminfo_ctrl[i]);
+			}
+		}
+	}
 
 	/* Save trimming info in order to perform calibration */
 	if (data->soc == SOC_ARCH_EXYNOS5440) {
@@ -197,7 +200,7 @@ static int exynos_tmu_initialize(struct platform_device *pdev)
 			trim_info = readl(data->base + reg->triminfo_data);
 	}
 	data->temp_error1 = trim_info & EXYNOS_TMU_TEMP_MASK;
-	data->temp_error2 = ((trim_info >> reg->triminfo_85_shift) &
+	data->temp_error2 = ((trim_info >> EXYNOS_TRIMINFO_85_SHIFT) &
 				EXYNOS_TMU_TEMP_MASK);
 
 	if (!data->temp_error1 ||
@@ -207,67 +210,33 @@ static int exynos_tmu_initialize(struct platform_device *pdev)
 
 	if (!data->temp_error2)
 		data->temp_error2 =
-			(pdata->efuse_value >> reg->triminfo_85_shift) &
+			(pdata->efuse_value >> EXYNOS_TRIMINFO_85_SHIFT) &
 			EXYNOS_TMU_TEMP_MASK;
 
-skip_calib_data:
-	if (pdata->max_trigger_level > MAX_THRESHOLD_LEVS) {
-		dev_err(&pdev->dev, "Invalid max trigger level\n");
-		ret = -EINVAL;
-		goto out;
-	}
-
-	for (i = 0; i < pdata->max_trigger_level; i++) {
-		if (!pdata->trigger_levels[i])
-			continue;
-
-		if ((pdata->trigger_type[i] == HW_TRIP) &&
-		(!pdata->trigger_levels[pdata->max_trigger_level - 1])) {
-			dev_err(&pdev->dev, "Invalid hw trigger level\n");
-			ret = -EINVAL;
-			goto out;
-		}
-
-		/* Count trigger levels except the HW trip*/
-		if (!(pdata->trigger_type[i] == HW_TRIP))
-			trigger_levs++;
-	}
-
 	rising_threshold = readl(data->base + reg->threshold_th0);
 
 	if (data->soc == SOC_ARCH_EXYNOS4210) {
 		/* Write temperature code for threshold */
 		threshold_code = temp_to_code(data, pdata->threshold);
-		if (threshold_code < 0) {
-			ret = threshold_code;
-			goto out;
-		}
 		writeb(threshold_code,
 			data->base + reg->threshold_temp);
-		for (i = 0; i < trigger_levs; i++)
+		for (i = 0; i < pdata->non_hw_trigger_levels; i++)
 			writeb(pdata->trigger_levels[i], data->base +
 			reg->threshold_th0 + i * sizeof(reg->threshold_th0));
 
-		writel(reg->intclr_rise_mask, data->base + reg->tmu_intclear);
+		exynos_tmu_clear_irqs(data);
 	} else {
 		/* Write temperature code for rising and falling threshold */
-		for (i = 0;
-		i < trigger_levs && i < EXYNOS_MAX_TRIGGER_PER_REG; i++) {
+		for (i = 0; i < pdata->non_hw_trigger_levels; i++) {
 			threshold_code = temp_to_code(data,
 						pdata->trigger_levels[i]);
-			if (threshold_code < 0) {
-				ret = threshold_code;
-				goto out;
-			}
 			rising_threshold &= ~(0xff << 8 * i);
 			rising_threshold |= threshold_code << 8 * i;
 			if (pdata->threshold_falling) {
 				threshold_code = temp_to_code(data,
 						pdata->trigger_levels[i] -
 						pdata->threshold_falling);
-				if (threshold_code > 0)
-					falling_threshold |=
-						threshold_code << 8 * i;
+				falling_threshold |= threshold_code << 8 * i;
 			}
 		}
 
@@ -276,9 +245,7 @@ skip_calib_data:
 		writel(falling_threshold,
 				data->base + reg->threshold_th1);
 
-		writel((reg->intclr_rise_mask << reg->intclr_rise_shift) |
-			(reg->intclr_fall_mask << reg->intclr_fall_shift),
-				data->base + reg->tmu_intclear);
+		exynos_tmu_clear_irqs(data);
 
 		/* if last threshold limit is also present */
 		i = pdata->max_trigger_level - 1;
@@ -286,10 +253,6 @@ skip_calib_data:
 				(pdata->trigger_type[i] == HW_TRIP)) {
 			threshold_code = temp_to_code(data,
 						pdata->trigger_levels[i]);
-			if (threshold_code < 0) {
-				ret = threshold_code;
-				goto out;
-			}
 			if (i == EXYNOS_MAX_TRIGGER_PER_REG - 1) {
 				/* 1-4 level to be assigned in th0 reg */
 				rising_threshold &= ~(0xff << 8 * i);
@@ -325,7 +288,7 @@ static void exynos_tmu_control(struct platform_device *pdev, bool on)
 	struct exynos_tmu_data *data = platform_get_drvdata(pdev);
 	struct exynos_tmu_platform_data *pdata = data->pdata;
 	const struct exynos_tmu_registers *reg = pdata->registers;
-	unsigned int con, interrupt_en, cal_val;
+	unsigned int con, interrupt_en;
 
 	mutex_lock(&data->lock);
 	clk_enable(data->clk);
@@ -335,15 +298,11 @@ static void exynos_tmu_control(struct platform_device *pdev, bool on)
 	if (pdata->test_mux)
 		con |= (pdata->test_mux << reg->test_mux_addr_shift);
 
-	if (pdata->reference_voltage) {
-		con &= ~(reg->buf_vref_sel_mask << reg->buf_vref_sel_shift);
-		con |= pdata->reference_voltage << reg->buf_vref_sel_shift;
-	}
+	con &= ~(EXYNOS_TMU_REF_VOLTAGE_MASK << EXYNOS_TMU_REF_VOLTAGE_SHIFT);
+	con |= pdata->reference_voltage << EXYNOS_TMU_REF_VOLTAGE_SHIFT;
 
-	if (pdata->gain) {
-		con &= ~(reg->buf_slope_sel_mask << reg->buf_slope_sel_shift);
-		con |= (pdata->gain << reg->buf_slope_sel_shift);
-	}
+	con &= ~(EXYNOS_TMU_BUF_SLOPE_SEL_MASK << EXYNOS_TMU_BUF_SLOPE_SEL_SHIFT);
+	con |= (pdata->gain << EXYNOS_TMU_BUF_SLOPE_SEL_SHIFT);
 
 	if (pdata->noise_cancel_mode) {
 		con &= ~(reg->therm_trip_mode_mask <<
@@ -351,29 +310,8 @@ static void exynos_tmu_control(struct platform_device *pdev, bool on)
 		con |= (pdata->noise_cancel_mode << reg->therm_trip_mode_shift);
 	}
 
-	if (pdata->cal_mode == HW_MODE) {
-		con &= ~(reg->calib_mode_mask << reg->calib_mode_shift);
-		cal_val = 0;
-		switch (pdata->cal_type) {
-		case TYPE_TWO_POINT_TRIMMING:
-			cal_val = 3;
-			break;
-		case TYPE_ONE_POINT_TRIMMING_85:
-			cal_val = 2;
-			break;
-		case TYPE_ONE_POINT_TRIMMING_25:
-			cal_val = 1;
-			break;
-		case TYPE_NONE:
-			break;
-		default:
-			dev_err(&pdev->dev, "Invalid calibration type, using none\n");
-		}
-		con |= cal_val << reg->calib_mode_shift;
-	}
-
 	if (on) {
-		con |= (1 << reg->core_en_shift);
+		con |= (1 << EXYNOS_TMU_CORE_EN_SHIFT);
 		interrupt_en =
 			pdata->trigger_enable[3] << reg->inten_rise3_shift |
 			pdata->trigger_enable[2] << reg->inten_rise2_shift |
@@ -383,7 +321,7 @@ static void exynos_tmu_control(struct platform_device *pdev, bool on)
 			interrupt_en |=
 				interrupt_en << reg->inten_fall0_shift;
 	} else {
-		con &= ~(1 << reg->core_en_shift);
+		con &= ~(1 << EXYNOS_TMU_CORE_EN_SHIFT);
 		interrupt_en = 0; /* Disable all interrupts */
 	}
 	writel(interrupt_en, data->base + reg->tmu_inten);
@@ -404,8 +342,16 @@ static int exynos_tmu_read(struct exynos_tmu_data *data)
 	clk_enable(data->clk);
 
 	temp_code = readb(data->base + reg->tmu_cur_temp);
-	temp = code_to_temp(data, temp_code);
 
+	if (data->soc == SOC_ARCH_EXYNOS4210)
+		/* temp_code should range between 75 and 175 */
+		if (temp_code < 75 || temp_code > 175) {
+			temp = -ENODATA;
+			goto out;
+		}
+
+	temp = code_to_temp(data, temp_code);
+out:
 	clk_disable(data->clk);
 	mutex_unlock(&data->lock);
 
@@ -465,7 +411,7 @@ static void exynos_tmu_work(struct work_struct *work)
 			struct exynos_tmu_data, irq_work);
 	struct exynos_tmu_platform_data *pdata = data->pdata;
 	const struct exynos_tmu_registers *reg = pdata->registers;
-	unsigned int val_irq, val_type;
+	unsigned int val_type;
 
 	if (!IS_ERR(data->clk_sec))
 		clk_enable(data->clk_sec);
@@ -483,9 +429,7 @@ static void exynos_tmu_work(struct work_struct *work)
 	clk_enable(data->clk);
 
 	/* TODO: take action based on particular interrupt */
-	val_irq = readl(data->base + reg->tmu_intstat);
-	/* clear the interrupts */
-	writel(val_irq, data->base + reg->tmu_intclear);
+	exynos_tmu_clear_irqs(data);
 
 	clk_disable(data->clk);
 	mutex_unlock(&data->lock);
diff --git a/drivers/thermal/samsung/exynos_tmu.h b/drivers/thermal/samsung/exynos_tmu.h
index 1b4a6444ea61..c58c7663a3fe 100644
--- a/drivers/thermal/samsung/exynos_tmu.h
+++ b/drivers/thermal/samsung/exynos_tmu.h
@@ -34,11 +34,6 @@ enum calibration_type {
 	TYPE_NONE,
 };
 
-enum calibration_mode {
-	SW_MODE,
-	HW_MODE,
-};
-
 enum soc_type {
 	SOC_ARCH_EXYNOS3250 = 1,
 	SOC_ARCH_EXYNOS4210,
@@ -82,46 +77,19 @@ enum soc_type {
  * bitfields. The register validity, offsets and bitfield values may vary
  * slightly across different exynos SOC's.
  * @triminfo_data: register containing 2 pont trimming data
- * @triminfo_25_shift: shift bit of the 25 C trim value in triminfo_data reg.
- * @triminfo_85_shift: shift bit of the 85 C trim value in triminfo_data reg.
  * @triminfo_ctrl: trim info controller register.
- * @triminfo_reload_shift: shift of triminfo reload enable bit in triminfo_ctrl
-	reg.
+ * @triminfo_ctrl_count: the number of trim info controller register.
  * @tmu_ctrl: TMU main controller register.
  * @test_mux_addr_shift: shift bits of test mux address.
- * @buf_vref_sel_shift: shift bits of reference voltage in tmu_ctrl register.
- * @buf_vref_sel_mask: mask bits of reference voltage in tmu_ctrl register.
  * @therm_trip_mode_shift: shift bits of tripping mode in tmu_ctrl register.
  * @therm_trip_mode_mask: mask bits of tripping mode in tmu_ctrl register.
  * @therm_trip_en_shift: shift bits of tripping enable in tmu_ctrl register.
- * @buf_slope_sel_shift: shift bits of amplifier gain value in tmu_ctrl
-	register.
- * @buf_slope_sel_mask: mask bits of amplifier gain value in tmu_ctrl register.
- * @calib_mode_shift: shift bits of calibration mode value in tmu_ctrl
-	register.
- * @calib_mode_mask: mask bits of calibration mode value in tmu_ctrl
-	register.
- * @therm_trip_tq_en_shift: shift bits of thermal trip enable by TQ pin in
-	tmu_ctrl register.
- * @core_en_shift: shift bits of TMU core enable bit in tmu_ctrl register.
  * @tmu_status: register drescribing the TMU status.
  * @tmu_cur_temp: register containing the current temperature of the TMU.
- * @tmu_cur_temp_shift: shift bits of current temp value in tmu_cur_temp
-	register.
  * @threshold_temp: register containing the base threshold level.
  * @threshold_th0: Register containing first set of rising levels.
- * @threshold_th0_l0_shift: shift bits of level0 threshold temperature.
- * @threshold_th0_l1_shift: shift bits of level1 threshold temperature.
- * @threshold_th0_l2_shift: shift bits of level2 threshold temperature.
- * @threshold_th0_l3_shift: shift bits of level3 threshold temperature.
  * @threshold_th1: Register containing second set of rising levels.
- * @threshold_th1_l0_shift: shift bits of level0 threshold temperature.
- * @threshold_th1_l1_shift: shift bits of level1 threshold temperature.
- * @threshold_th1_l2_shift: shift bits of level2 threshold temperature.
- * @threshold_th1_l3_shift: shift bits of level3 threshold temperature.
  * @threshold_th2: Register containing third set of rising levels.
- * @threshold_th2_l0_shift: shift bits of level0 threshold temperature.
- * @threshold_th3: Register containing fourth set of rising levels.
  * @threshold_th3_l0_shift: shift bits of level0 threshold temperature.
  * @tmu_inten: register containing the different threshold interrupt
 	enable bits.
@@ -130,68 +98,35 @@ enum soc_type {
  * @inten_rise2_shift: shift bits of rising 2 interrupt bits.
  * @inten_rise3_shift: shift bits of rising 3 interrupt bits.
  * @inten_fall0_shift: shift bits of falling 0 interrupt bits.
- * @inten_fall1_shift: shift bits of falling 1 interrupt bits.
- * @inten_fall2_shift: shift bits of falling 2 interrupt bits.
- * @inten_fall3_shift: shift bits of falling 3 interrupt bits.
  * @tmu_intstat: Register containing the interrupt status values.
  * @tmu_intclear: Register for clearing the raised interrupt status.
- * @intclr_fall_shift: shift bits for interrupt clear fall 0
- * @intclr_rise_shift: shift bits of all rising interrupt bits.
- * @intclr_rise_mask: mask bits of all rising interrupt bits.
- * @intclr_fall_mask: mask bits of all rising interrupt bits.
  * @emul_con: TMU emulation controller register.
  * @emul_temp_shift: shift bits of emulation temperature.
  * @emul_time_shift: shift bits of emulation time.
- * @emul_time_mask: mask bits of emulation time.
  * @tmu_irqstatus: register to find which TMU generated interrupts.
  * @tmu_pmin: register to get/set the Pmin value.
  */
 struct exynos_tmu_registers {
 	u32	triminfo_data;
-	u32	triminfo_25_shift;
-	u32	triminfo_85_shift;
 
-	u32	triminfo_ctrl;
-	u32	triminfo_ctrl1;
-	u32	triminfo_reload_shift;
+	u32	triminfo_ctrl[MAX_TRIMINFO_CTRL_REG];
+	u32	triminfo_ctrl_count;
 
 	u32	tmu_ctrl;
 	u32     test_mux_addr_shift;
-	u32	buf_vref_sel_shift;
-	u32	buf_vref_sel_mask;
 	u32	therm_trip_mode_shift;
 	u32	therm_trip_mode_mask;
 	u32	therm_trip_en_shift;
-	u32	buf_slope_sel_shift;
-	u32	buf_slope_sel_mask;
-	u32	calib_mode_shift;
-	u32	calib_mode_mask;
-	u32	therm_trip_tq_en_shift;
-	u32	core_en_shift;
 
 	u32	tmu_status;
 
 	u32	tmu_cur_temp;
-	u32	tmu_cur_temp_shift;
 
 	u32	threshold_temp;
 
 	u32	threshold_th0;
-	u32	threshold_th0_l0_shift;
-	u32	threshold_th0_l1_shift;
-	u32	threshold_th0_l2_shift;
-	u32	threshold_th0_l3_shift;
-
 	u32	threshold_th1;
-	u32	threshold_th1_l0_shift;
-	u32	threshold_th1_l1_shift;
-	u32	threshold_th1_l2_shift;
-	u32	threshold_th1_l3_shift;
-
 	u32	threshold_th2;
-	u32	threshold_th2_l0_shift;
-
-	u32	threshold_th3;
 	u32	threshold_th3_l0_shift;
 
 	u32	tmu_inten;
@@ -200,22 +135,14 @@ struct exynos_tmu_registers {
 	u32	inten_rise2_shift;
 	u32	inten_rise3_shift;
 	u32	inten_fall0_shift;
-	u32	inten_fall1_shift;
-	u32	inten_fall2_shift;
-	u32	inten_fall3_shift;
 
 	u32	tmu_intstat;
 
 	u32	tmu_intclear;
-	u32	intclr_fall_shift;
-	u32	intclr_rise_shift;
-	u32	intclr_fall_mask;
-	u32	intclr_rise_mask;
 
 	u32	emul_con;
 	u32	emul_temp_shift;
 	u32	emul_time_shift;
-	u32	emul_time_mask;
 
 	u32	tmu_irqstatus;
 	u32	tmu_pmin;
@@ -250,11 +177,12 @@ struct exynos_tmu_registers {
  *	1 = enable trigger_level[] interrupt,
  *	0 = disable trigger_level[] interrupt
  * @max_trigger_level: max trigger level supported by the TMU
+ * @non_hw_trigger_levels: number of defined non-hardware trigger levels
  * @gain: gain of amplifier in the positive-TC generator block
- *	0 <= gain <= 15
+ *	0 < gain <= 15
  * @reference_voltage: reference voltage of amplifier
  *	in the positive-TC generator block
- *	0 <= reference_voltage <= 31
+ *	0 < reference_voltage <= 31
  * @noise_cancel_mode: noise cancellation mode
  *	000, 100, 101, 110 and 111 can be different modes
  * @type: determines the type of SOC
@@ -265,8 +193,8 @@ struct exynos_tmu_registers {
  * @second_point_trim: temp value of the second point trimming
  * @default_temp_offset: default temperature offset in case of no trimming
  * @test_mux; information if SoC supports test MUX
+ * @triminfo_reload: reload value to read TRIMINFO register
  * @cal_type: calibration type for temperature
- * @cal_mode: calibration mode for temperature
  * @freq_clip_table: Table representing frequency reduction percentage.
  * @freq_tab_count: Count of the above table as frequency reduction may
  *	applicable to only some of the trigger levels.
@@ -284,6 +212,7 @@ struct exynos_tmu_platform_data {
 	enum trigger_type trigger_type[MAX_TRIP_COUNT];
 	bool trigger_enable[MAX_TRIP_COUNT];
 	u8 max_trigger_level;
+	u8 non_hw_trigger_levels;
 	u8 gain;
 	u8 reference_voltage;
 	u8 noise_cancel_mode;
@@ -295,9 +224,9 @@ struct exynos_tmu_platform_data {
 	u8 second_point_trim;
 	u8 default_temp_offset;
 	u8 test_mux;
+	u8 triminfo_reload[MAX_TRIMINFO_CTRL_REG];
 
 	enum calibration_type cal_type;
-	enum calibration_mode cal_mode;
 	enum soc_type type;
 	struct freq_clip_table freq_tab[4];
 	unsigned int freq_tab_count;
diff --git a/drivers/thermal/samsung/exynos_tmu_data.c b/drivers/thermal/samsung/exynos_tmu_data.c
index aa8e0dee2055..2683d2897e90 100644
--- a/drivers/thermal/samsung/exynos_tmu_data.c
+++ b/drivers/thermal/samsung/exynos_tmu_data.c
@@ -27,14 +27,7 @@
 #if defined(CONFIG_CPU_EXYNOS4210)
 static const struct exynos_tmu_registers exynos4210_tmu_registers = {
 	.triminfo_data = EXYNOS_TMU_REG_TRIMINFO,
-	.triminfo_25_shift = EXYNOS_TRIMINFO_25_SHIFT,
-	.triminfo_85_shift = EXYNOS_TRIMINFO_85_SHIFT,
 	.tmu_ctrl = EXYNOS_TMU_REG_CONTROL,
-	.buf_vref_sel_shift = EXYNOS_TMU_REF_VOLTAGE_SHIFT,
-	.buf_vref_sel_mask = EXYNOS_TMU_REF_VOLTAGE_MASK,
-	.buf_slope_sel_shift = EXYNOS_TMU_BUF_SLOPE_SEL_SHIFT,
-	.buf_slope_sel_mask = EXYNOS_TMU_BUF_SLOPE_SEL_MASK,
-	.core_en_shift = EXYNOS_TMU_CORE_EN_SHIFT,
 	.tmu_status = EXYNOS_TMU_REG_STATUS,
 	.tmu_cur_temp = EXYNOS_TMU_REG_CURRENT_TEMP,
 	.threshold_temp = EXYNOS4210_TMU_REG_THRESHOLD_TEMP,
@@ -46,7 +39,6 @@ static const struct exynos_tmu_registers exynos4210_tmu_registers = {
 	.inten_rise3_shift = EXYNOS_TMU_INTEN_RISE3_SHIFT,
 	.tmu_intstat = EXYNOS_TMU_REG_INTSTAT,
 	.tmu_intclear = EXYNOS_TMU_REG_INTCLEAR,
-	.intclr_rise_mask = EXYNOS4210_TMU_TRIG_LEVEL_MASK,
 };
 
 struct exynos_tmu_init_data const exynos4210_default_tmu_data = {
@@ -64,6 +56,7 @@ struct exynos_tmu_init_data const exynos4210_default_tmu_data = {
 		.trigger_type[1] = THROTTLE_ACTIVE,
 		.trigger_type[2] = SW_TRIP,
 		.max_trigger_level = 4,
+		.non_hw_trigger_levels = 3,
 		.gain = 15,
 		.reference_voltage = 7,
 		.cal_type = TYPE_ONE_POINT_TRIMMING,
@@ -93,18 +86,14 @@ struct exynos_tmu_init_data const exynos4210_default_tmu_data = {
 #if defined(CONFIG_SOC_EXYNOS3250)
 static const struct exynos_tmu_registers exynos3250_tmu_registers = {
 	.triminfo_data = EXYNOS_TMU_REG_TRIMINFO,
-	.triminfo_25_shift = EXYNOS_TRIMINFO_25_SHIFT,
-	.triminfo_85_shift = EXYNOS_TRIMINFO_85_SHIFT,
+	.triminfo_ctrl[0] = EXYNOS_TMU_TRIMINFO_CON1,
+	.triminfo_ctrl[1] = EXYNOS_TMU_TRIMINFO_CON2,
+	.triminfo_ctrl_count = 2,
 	.tmu_ctrl = EXYNOS_TMU_REG_CONTROL,
 	.test_mux_addr_shift = EXYNOS4412_MUX_ADDR_SHIFT,
-	.buf_vref_sel_shift = EXYNOS_TMU_REF_VOLTAGE_SHIFT,
-	.buf_vref_sel_mask = EXYNOS_TMU_REF_VOLTAGE_MASK,
 	.therm_trip_mode_shift = EXYNOS_TMU_TRIP_MODE_SHIFT,
 	.therm_trip_mode_mask = EXYNOS_TMU_TRIP_MODE_MASK,
 	.therm_trip_en_shift = EXYNOS_TMU_THERM_TRIP_EN_SHIFT,
-	.buf_slope_sel_shift = EXYNOS_TMU_BUF_SLOPE_SEL_SHIFT,
-	.buf_slope_sel_mask = EXYNOS_TMU_BUF_SLOPE_SEL_MASK,
-	.core_en_shift = EXYNOS_TMU_CORE_EN_SHIFT,
 	.tmu_status = EXYNOS_TMU_REG_STATUS,
 	.tmu_cur_temp = EXYNOS_TMU_REG_CURRENT_TEMP,
 	.threshold_th0 = EXYNOS_THD_TEMP_RISE,
@@ -116,14 +105,9 @@ static const struct exynos_tmu_registers exynos3250_tmu_registers = {
 	.inten_fall0_shift = EXYNOS_TMU_INTEN_FALL0_SHIFT,
 	.tmu_intstat = EXYNOS_TMU_REG_INTSTAT,
 	.tmu_intclear = EXYNOS_TMU_REG_INTCLEAR,
-	.intclr_fall_shift = EXYNOS_TMU_CLEAR_FALL_INT_SHIFT,
-	.intclr_rise_shift = EXYNOS_TMU_RISE_INT_SHIFT,
-	.intclr_rise_mask = EXYNOS_TMU_RISE_INT_MASK,
-	.intclr_fall_mask = EXYNOS_TMU_FALL_INT_MASK,
 	.emul_con = EXYNOS_EMUL_CON,
 	.emul_temp_shift = EXYNOS_EMUL_DATA_SHIFT,
 	.emul_time_shift = EXYNOS_EMUL_TIME_SHIFT,
-	.emul_time_mask = EXYNOS_EMUL_TIME_MASK,
 };
 
 #define EXYNOS3250_TMU_DATA \
@@ -141,6 +125,7 @@ static const struct exynos_tmu_registers exynos3250_tmu_registers = {
 	.trigger_type[2] = SW_TRIP, \
 	.trigger_type[3] = HW_TRIP, \
 	.max_trigger_level = 4, \
+	.non_hw_trigger_levels = 3, \
 	.gain = 8, \
 	.reference_voltage = 16, \
 	.noise_cancel_mode = 4, \
@@ -160,8 +145,10 @@ static const struct exynos_tmu_registers exynos3250_tmu_registers = {
 		.temp_level = 95, \
 	}, \
 	.freq_tab_count = 2, \
+	.triminfo_reload[0] = EXYNOS_TRIMINFO_RELOAD_ENABLE, \
+	.triminfo_reload[1] = EXYNOS_TRIMINFO_RELOAD_ENABLE, \
 	.registers = &exynos3250_tmu_registers, \
-	.features = (TMU_SUPPORT_EMULATION | \
+	.features = (TMU_SUPPORT_EMULATION | TMU_SUPPORT_TRIM_RELOAD | \
 			TMU_SUPPORT_FALLING_TRIP | TMU_SUPPORT_READY_STATUS | \
 			TMU_SUPPORT_EMUL_TIME)
 #endif
@@ -182,20 +169,13 @@ struct exynos_tmu_init_data const exynos3250_default_tmu_data = {
 #if defined(CONFIG_SOC_EXYNOS4412) || defined(CONFIG_SOC_EXYNOS5250)
 static const struct exynos_tmu_registers exynos4412_tmu_registers = {
 	.triminfo_data = EXYNOS_TMU_REG_TRIMINFO,
-	.triminfo_25_shift = EXYNOS_TRIMINFO_25_SHIFT,
-	.triminfo_85_shift = EXYNOS_TRIMINFO_85_SHIFT,
-	.triminfo_ctrl = EXYNOS_TMU_TRIMINFO_CON,
-	.triminfo_reload_shift = EXYNOS_TRIMINFO_RELOAD_SHIFT,
+	.triminfo_ctrl[0] = EXYNOS_TMU_TRIMINFO_CON2,
+	.triminfo_ctrl_count = 1,
 	.tmu_ctrl = EXYNOS_TMU_REG_CONTROL,
 	.test_mux_addr_shift = EXYNOS4412_MUX_ADDR_SHIFT,
-	.buf_vref_sel_shift = EXYNOS_TMU_REF_VOLTAGE_SHIFT,
-	.buf_vref_sel_mask = EXYNOS_TMU_REF_VOLTAGE_MASK,
 	.therm_trip_mode_shift = EXYNOS_TMU_TRIP_MODE_SHIFT,
 	.therm_trip_mode_mask = EXYNOS_TMU_TRIP_MODE_MASK,
 	.therm_trip_en_shift = EXYNOS_TMU_THERM_TRIP_EN_SHIFT,
-	.buf_slope_sel_shift = EXYNOS_TMU_BUF_SLOPE_SEL_SHIFT,
-	.buf_slope_sel_mask = EXYNOS_TMU_BUF_SLOPE_SEL_MASK,
-	.core_en_shift = EXYNOS_TMU_CORE_EN_SHIFT,
 	.tmu_status = EXYNOS_TMU_REG_STATUS,
 	.tmu_cur_temp = EXYNOS_TMU_REG_CURRENT_TEMP,
 	.threshold_th0 = EXYNOS_THD_TEMP_RISE,
@@ -208,14 +188,9 @@ static const struct exynos_tmu_registers exynos4412_tmu_registers = {
 	.inten_fall0_shift = EXYNOS_TMU_INTEN_FALL0_SHIFT,
 	.tmu_intstat = EXYNOS_TMU_REG_INTSTAT,
 	.tmu_intclear = EXYNOS_TMU_REG_INTCLEAR,
-	.intclr_fall_shift = EXYNOS_TMU_CLEAR_FALL_INT_SHIFT,
-	.intclr_rise_shift = EXYNOS_TMU_RISE_INT_SHIFT,
-	.intclr_rise_mask = EXYNOS_TMU_RISE_INT_MASK,
-	.intclr_fall_mask = EXYNOS_TMU_FALL_INT_MASK,
 	.emul_con = EXYNOS_EMUL_CON,
 	.emul_temp_shift = EXYNOS_EMUL_DATA_SHIFT,
 	.emul_time_shift = EXYNOS_EMUL_TIME_SHIFT,
-	.emul_time_mask = EXYNOS_EMUL_TIME_MASK,
 };
 
 #define EXYNOS4412_TMU_DATA \
@@ -233,6 +208,7 @@ static const struct exynos_tmu_registers exynos4412_tmu_registers = {
 	.trigger_type[2] = SW_TRIP, \
 	.trigger_type[3] = HW_TRIP, \
 	.max_trigger_level = 4, \
+	.non_hw_trigger_levels = 3, \
 	.gain = 8, \
 	.reference_voltage = 16, \
 	.noise_cancel_mode = 4, \
@@ -252,6 +228,7 @@ static const struct exynos_tmu_registers exynos4412_tmu_registers = {
 		.temp_level = 95, \
 	}, \
 	.freq_tab_count = 2, \
+	.triminfo_reload[0] = EXYNOS_TRIMINFO_RELOAD_ENABLE, \
 	.registers = &exynos4412_tmu_registers, \
 	.features = (TMU_SUPPORT_EMULATION | TMU_SUPPORT_TRIM_RELOAD | \
 			TMU_SUPPORT_FALLING_TRIP | TMU_SUPPORT_READY_STATUS | \
@@ -286,18 +263,11 @@ struct exynos_tmu_init_data const exynos5250_default_tmu_data = {
 #if defined(CONFIG_SOC_EXYNOS5260)
 static const struct exynos_tmu_registers exynos5260_tmu_registers = {
 	.triminfo_data = EXYNOS_TMU_REG_TRIMINFO,
-	.triminfo_25_shift = EXYNOS_TRIMINFO_25_SHIFT,
-	.triminfo_85_shift = EXYNOS_TRIMINFO_85_SHIFT,
 	.tmu_ctrl = EXYNOS_TMU_REG_CONTROL,
 	.tmu_ctrl = EXYNOS_TMU_REG_CONTROL1,
-	.buf_vref_sel_shift = EXYNOS_TMU_REF_VOLTAGE_SHIFT,
-	.buf_vref_sel_mask = EXYNOS_TMU_REF_VOLTAGE_MASK,
 	.therm_trip_mode_shift = EXYNOS_TMU_TRIP_MODE_SHIFT,
 	.therm_trip_mode_mask = EXYNOS_TMU_TRIP_MODE_MASK,
 	.therm_trip_en_shift = EXYNOS_TMU_THERM_TRIP_EN_SHIFT,
-	.buf_slope_sel_shift = EXYNOS_TMU_BUF_SLOPE_SEL_SHIFT,
-	.buf_slope_sel_mask = EXYNOS_TMU_BUF_SLOPE_SEL_MASK,
-	.core_en_shift = EXYNOS_TMU_CORE_EN_SHIFT,
 	.tmu_status = EXYNOS_TMU_REG_STATUS,
 	.tmu_cur_temp = EXYNOS_TMU_REG_CURRENT_TEMP,
 	.threshold_th0 = EXYNOS_THD_TEMP_RISE,
@@ -310,14 +280,9 @@ static const struct exynos_tmu_registers exynos5260_tmu_registers = {
 	.inten_fall0_shift = EXYNOS_TMU_INTEN_FALL0_SHIFT,
 	.tmu_intstat = EXYNOS5260_TMU_REG_INTSTAT,
 	.tmu_intclear = EXYNOS5260_TMU_REG_INTCLEAR,
-	.intclr_fall_shift = EXYNOS5420_TMU_CLEAR_FALL_INT_SHIFT,
-	.intclr_rise_shift = EXYNOS_TMU_RISE_INT_SHIFT,
-	.intclr_rise_mask = EXYNOS5260_TMU_RISE_INT_MASK,
-	.intclr_fall_mask = EXYNOS5260_TMU_FALL_INT_MASK,
 	.emul_con = EXYNOS5260_EMUL_CON,
 	.emul_temp_shift = EXYNOS_EMUL_DATA_SHIFT,
 	.emul_time_shift = EXYNOS_EMUL_TIME_SHIFT,
-	.emul_time_mask = EXYNOS_EMUL_TIME_MASK,
 };
 
 #define __EXYNOS5260_TMU_DATA	\
@@ -335,6 +300,7 @@ static const struct exynos_tmu_registers exynos5260_tmu_registers = {
 	.trigger_type[2] = SW_TRIP, \
 	.trigger_type[3] = HW_TRIP, \
 	.max_trigger_level = 4, \
+	.non_hw_trigger_levels = 3, \
 	.gain = 8, \
 	.reference_voltage = 16, \
 	.noise_cancel_mode = 4, \
@@ -359,9 +325,8 @@ static const struct exynos_tmu_registers exynos5260_tmu_registers = {
 #define EXYNOS5260_TMU_DATA \
 	__EXYNOS5260_TMU_DATA \
 	.type = SOC_ARCH_EXYNOS5260, \
-	.features = (TMU_SUPPORT_EMULATION | TMU_SUPPORT_TRIM_RELOAD | \
-			TMU_SUPPORT_FALLING_TRIP | TMU_SUPPORT_READY_STATUS | \
-			TMU_SUPPORT_EMUL_TIME)
+	.features = (TMU_SUPPORT_EMULATION | TMU_SUPPORT_FALLING_TRIP | \
+			TMU_SUPPORT_READY_STATUS | TMU_SUPPORT_EMUL_TIME)
 
 struct exynos_tmu_init_data const exynos5260_default_tmu_data = {
 	.tmu_data = {
@@ -378,17 +343,10 @@ struct exynos_tmu_init_data const exynos5260_default_tmu_data = {
 #if defined(CONFIG_SOC_EXYNOS5420)
 static const struct exynos_tmu_registers exynos5420_tmu_registers = {
 	.triminfo_data = EXYNOS_TMU_REG_TRIMINFO,
-	.triminfo_25_shift = EXYNOS_TRIMINFO_25_SHIFT,
-	.triminfo_85_shift = EXYNOS_TRIMINFO_85_SHIFT,
 	.tmu_ctrl = EXYNOS_TMU_REG_CONTROL,
-	.buf_vref_sel_shift = EXYNOS_TMU_REF_VOLTAGE_SHIFT,
-	.buf_vref_sel_mask = EXYNOS_TMU_REF_VOLTAGE_MASK,
 	.therm_trip_mode_shift = EXYNOS_TMU_TRIP_MODE_SHIFT,
 	.therm_trip_mode_mask = EXYNOS_TMU_TRIP_MODE_MASK,
 	.therm_trip_en_shift = EXYNOS_TMU_THERM_TRIP_EN_SHIFT,
-	.buf_slope_sel_shift = EXYNOS_TMU_BUF_SLOPE_SEL_SHIFT,
-	.buf_slope_sel_mask = EXYNOS_TMU_BUF_SLOPE_SEL_MASK,
-	.core_en_shift = EXYNOS_TMU_CORE_EN_SHIFT,
 	.tmu_status = EXYNOS_TMU_REG_STATUS,
 	.tmu_cur_temp = EXYNOS_TMU_REG_CURRENT_TEMP,
 	.threshold_th0 = EXYNOS_THD_TEMP_RISE,
@@ -402,14 +360,9 @@ static const struct exynos_tmu_registers exynos5420_tmu_registers = {
 	.inten_fall0_shift = EXYNOS_TMU_INTEN_FALL0_SHIFT,
 	.tmu_intstat = EXYNOS_TMU_REG_INTSTAT,
 	.tmu_intclear = EXYNOS_TMU_REG_INTCLEAR,
-	.intclr_fall_shift = EXYNOS5420_TMU_CLEAR_FALL_INT_SHIFT,
-	.intclr_rise_shift = EXYNOS_TMU_RISE_INT_SHIFT,
-	.intclr_rise_mask = EXYNOS_TMU_RISE_INT_MASK,
-	.intclr_fall_mask = EXYNOS_TMU_FALL_INT_MASK,
 	.emul_con = EXYNOS_EMUL_CON,
 	.emul_temp_shift = EXYNOS_EMUL_DATA_SHIFT,
 	.emul_time_shift = EXYNOS_EMUL_TIME_SHIFT,
-	.emul_time_mask = EXYNOS_EMUL_TIME_MASK,
 };
 
 #define __EXYNOS5420_TMU_DATA	\
@@ -427,6 +380,7 @@ static const struct exynos_tmu_registers exynos5420_tmu_registers = {
 	.trigger_type[2] = SW_TRIP, \
 	.trigger_type[3] = HW_TRIP, \
 	.max_trigger_level = 4, \
+	.non_hw_trigger_levels = 3, \
 	.gain = 8, \
 	.reference_voltage = 16, \
 	.noise_cancel_mode = 4, \
@@ -451,16 +405,15 @@ static const struct exynos_tmu_registers exynos5420_tmu_registers = {
 #define EXYNOS5420_TMU_DATA \
 	__EXYNOS5420_TMU_DATA \
 	.type = SOC_ARCH_EXYNOS5250, \
-	.features = (TMU_SUPPORT_EMULATION | TMU_SUPPORT_TRIM_RELOAD | \
-			TMU_SUPPORT_FALLING_TRIP | TMU_SUPPORT_READY_STATUS | \
-			TMU_SUPPORT_EMUL_TIME)
+	.features = (TMU_SUPPORT_EMULATION | TMU_SUPPORT_FALLING_TRIP | \
+			TMU_SUPPORT_READY_STATUS | TMU_SUPPORT_EMUL_TIME)
 
 #define EXYNOS5420_TMU_DATA_SHARED \
 	__EXYNOS5420_TMU_DATA \
 	.type = SOC_ARCH_EXYNOS5420_TRIMINFO, \
-	.features = (TMU_SUPPORT_EMULATION | TMU_SUPPORT_TRIM_RELOAD | \
-			TMU_SUPPORT_FALLING_TRIP | TMU_SUPPORT_READY_STATUS | \
-			TMU_SUPPORT_EMUL_TIME | TMU_SUPPORT_ADDRESS_MULTIPLE)
+	.features = (TMU_SUPPORT_EMULATION | TMU_SUPPORT_FALLING_TRIP | \
+			TMU_SUPPORT_READY_STATUS | TMU_SUPPORT_EMUL_TIME | \
+			TMU_SUPPORT_ADDRESS_MULTIPLE)
 
 struct exynos_tmu_init_data const exynos5420_default_tmu_data = {
 	.tmu_data = {
@@ -477,19 +430,10 @@ struct exynos_tmu_init_data const exynos5420_default_tmu_data = {
 #if defined(CONFIG_SOC_EXYNOS5440)
 static const struct exynos_tmu_registers exynos5440_tmu_registers = {
 	.triminfo_data = EXYNOS5440_TMU_S0_7_TRIM,
-	.triminfo_25_shift = EXYNOS_TRIMINFO_25_SHIFT,
-	.triminfo_85_shift = EXYNOS_TRIMINFO_85_SHIFT,
 	.tmu_ctrl = EXYNOS5440_TMU_S0_7_CTRL,
-	.buf_vref_sel_shift = EXYNOS_TMU_REF_VOLTAGE_SHIFT,
-	.buf_vref_sel_mask = EXYNOS_TMU_REF_VOLTAGE_MASK,
 	.therm_trip_mode_shift = EXYNOS_TMU_TRIP_MODE_SHIFT,
 	.therm_trip_mode_mask = EXYNOS_TMU_TRIP_MODE_MASK,
 	.therm_trip_en_shift = EXYNOS_TMU_THERM_TRIP_EN_SHIFT,
-	.buf_slope_sel_shift = EXYNOS_TMU_BUF_SLOPE_SEL_SHIFT,
-	.buf_slope_sel_mask = EXYNOS_TMU_BUF_SLOPE_SEL_MASK,
-	.calib_mode_shift = EXYNOS_TMU_CALIB_MODE_SHIFT,
-	.calib_mode_mask = EXYNOS_TMU_CALIB_MODE_MASK,
-	.core_en_shift = EXYNOS_TMU_CORE_EN_SHIFT,
 	.tmu_status = EXYNOS5440_TMU_S0_7_STATUS,
 	.tmu_cur_temp = EXYNOS5440_TMU_S0_7_TEMP,
 	.threshold_th0 = EXYNOS5440_TMU_S0_7_TH0,
@@ -504,10 +448,6 @@ static const struct exynos_tmu_registers exynos5440_tmu_registers = {
 	.inten_fall0_shift = EXYNOS5440_TMU_INTEN_FALL0_SHIFT,
 	.tmu_intstat = EXYNOS5440_TMU_S0_7_IRQ,
 	.tmu_intclear = EXYNOS5440_TMU_S0_7_IRQ,
-	.intclr_fall_shift = EXYNOS5440_TMU_CLEAR_FALL_INT_SHIFT,
-	.intclr_rise_shift = EXYNOS5440_TMU_RISE_INT_SHIFT,
-	.intclr_rise_mask = EXYNOS5440_TMU_RISE_INT_MASK,
-	.intclr_fall_mask = EXYNOS5440_TMU_FALL_INT_MASK,
 	.tmu_irqstatus = EXYNOS5440_TMU_IRQ_STATUS,
 	.emul_con = EXYNOS5440_TMU_S0_7_DEBUG,
 	.emul_temp_shift = EXYNOS_EMUL_DATA_SHIFT,
@@ -521,11 +461,11 @@ static const struct exynos_tmu_registers exynos5440_tmu_registers = {
 	.trigger_type[0] = SW_TRIP, \
 	.trigger_type[4] = HW_TRIP, \
 	.max_trigger_level = 5, \
+	.non_hw_trigger_levels = 1, \
 	.gain = 5, \
 	.reference_voltage = 16, \
 	.noise_cancel_mode = 4, \
 	.cal_type = TYPE_ONE_POINT_TRIMMING, \
-	.cal_mode = 0, \
 	.efuse_value = 0x5b2d, \
 	.min_efuse_value = 16, \
 	.max_efuse_value = 76, \
diff --git a/drivers/thermal/samsung/exynos_tmu_data.h b/drivers/thermal/samsung/exynos_tmu_data.h
index f0979e598491..65e2ea6a9579 100644
--- a/drivers/thermal/samsung/exynos_tmu_data.h
+++ b/drivers/thermal/samsung/exynos_tmu_data.h
@@ -39,55 +39,31 @@
 #define EXYNOS_TMU_BUF_SLOPE_SEL_SHIFT	8
 #define EXYNOS_TMU_CORE_EN_SHIFT	0
 
+/* Exynos3250 specific registers */
+#define EXYNOS_TMU_TRIMINFO_CON1	0x10
+
 /* Exynos4210 specific registers */
 #define EXYNOS4210_TMU_REG_THRESHOLD_TEMP	0x44
 #define EXYNOS4210_TMU_REG_TRIG_LEVEL0	0x50
-#define EXYNOS4210_TMU_REG_TRIG_LEVEL1	0x54
-#define EXYNOS4210_TMU_REG_TRIG_LEVEL2	0x58
-#define EXYNOS4210_TMU_REG_TRIG_LEVEL3	0x5C
-#define EXYNOS4210_TMU_REG_PAST_TEMP0	0x60
-#define EXYNOS4210_TMU_REG_PAST_TEMP1	0x64
-#define EXYNOS4210_TMU_REG_PAST_TEMP2	0x68
-#define EXYNOS4210_TMU_REG_PAST_TEMP3	0x6C
 
-#define EXYNOS4210_TMU_TRIG_LEVEL0_MASK	0x1
-#define EXYNOS4210_TMU_TRIG_LEVEL1_MASK	0x10
-#define EXYNOS4210_TMU_TRIG_LEVEL2_MASK	0x100
-#define EXYNOS4210_TMU_TRIG_LEVEL3_MASK	0x1000
-#define EXYNOS4210_TMU_TRIG_LEVEL_MASK	0x1111
-#define EXYNOS4210_TMU_INTCLEAR_VAL	0x1111
-
-/* Exynos5250 and Exynos4412 specific registers */
-#define EXYNOS_TMU_TRIMINFO_CON	0x14
+/* Exynos5250, Exynos4412, Exynos3250 specific registers */
+#define EXYNOS_TMU_TRIMINFO_CON2	0x14
 #define EXYNOS_THD_TEMP_RISE		0x50
 #define EXYNOS_THD_TEMP_FALL		0x54
 #define EXYNOS_EMUL_CON		0x80
 
-#define EXYNOS_TRIMINFO_RELOAD_SHIFT	1
+#define EXYNOS_TRIMINFO_RELOAD_ENABLE	1
 #define EXYNOS_TRIMINFO_25_SHIFT	0
 #define EXYNOS_TRIMINFO_85_SHIFT	8
-#define EXYNOS_TMU_RISE_INT_MASK	0x111
-#define EXYNOS_TMU_RISE_INT_SHIFT	0
-#define EXYNOS_TMU_FALL_INT_MASK	0x111
-#define EXYNOS_TMU_CLEAR_RISE_INT	0x111
-#define EXYNOS_TMU_CLEAR_FALL_INT	(0x111 << 12)
-#define EXYNOS_TMU_CLEAR_FALL_INT_SHIFT	12
-#define EXYNOS5420_TMU_CLEAR_FALL_INT_SHIFT	16
-#define EXYNOS5440_TMU_CLEAR_FALL_INT_SHIFT	4
 #define EXYNOS_TMU_TRIP_MODE_SHIFT	13
 #define EXYNOS_TMU_TRIP_MODE_MASK	0x7
 #define EXYNOS_TMU_THERM_TRIP_EN_SHIFT	12
-#define EXYNOS_TMU_CALIB_MODE_SHIFT	4
-#define EXYNOS_TMU_CALIB_MODE_MASK	0x3
 
 #define EXYNOS_TMU_INTEN_RISE0_SHIFT	0
 #define EXYNOS_TMU_INTEN_RISE1_SHIFT	4
 #define EXYNOS_TMU_INTEN_RISE2_SHIFT	8
 #define EXYNOS_TMU_INTEN_RISE3_SHIFT	12
 #define EXYNOS_TMU_INTEN_FALL0_SHIFT	16
-#define EXYNOS_TMU_INTEN_FALL1_SHIFT	20
-#define EXYNOS_TMU_INTEN_FALL2_SHIFT	24
-#define EXYNOS_TMU_INTEN_FALL3_SHIFT	28
 
 #define EXYNOS_EMUL_TIME	0x57F0
 #define EXYNOS_EMUL_TIME_MASK	0xffff
@@ -103,10 +79,6 @@
 #define EXYNOS5260_TMU_REG_INTEN		0xC0
 #define EXYNOS5260_TMU_REG_INTSTAT		0xC4
 #define EXYNOS5260_TMU_REG_INTCLEAR		0xC8
-#define EXYNOS5260_TMU_CLEAR_RISE_INT		0x1111
-#define EXYNOS5260_TMU_CLEAR_FALL_INT		(0x1111 << 16)
-#define EXYNOS5260_TMU_RISE_INT_MASK		0x1111
-#define EXYNOS5260_TMU_FALL_INT_MASK		0x1111
 #define EXYNOS5260_EMUL_CON			0x100
 
 /* Exynos4412 specific */
@@ -122,29 +94,17 @@
 #define EXYNOS5440_TMU_S0_7_TH0			0x110
 #define EXYNOS5440_TMU_S0_7_TH1			0x130
 #define EXYNOS5440_TMU_S0_7_TH2			0x150
-#define EXYNOS5440_TMU_S0_7_EVTEN		0x1F0
 #define EXYNOS5440_TMU_S0_7_IRQEN		0x210
 #define EXYNOS5440_TMU_S0_7_IRQ			0x230
 /* exynos5440 common registers */
 #define EXYNOS5440_TMU_IRQ_STATUS		0x000
 #define EXYNOS5440_TMU_PMIN			0x004
-#define EXYNOS5440_TMU_TEMP			0x008
 
-#define EXYNOS5440_TMU_RISE_INT_MASK		0xf
-#define EXYNOS5440_TMU_RISE_INT_SHIFT		0
-#define EXYNOS5440_TMU_FALL_INT_MASK		0xf
 #define EXYNOS5440_TMU_INTEN_RISE0_SHIFT	0
 #define EXYNOS5440_TMU_INTEN_RISE1_SHIFT	1
 #define EXYNOS5440_TMU_INTEN_RISE2_SHIFT	2
 #define EXYNOS5440_TMU_INTEN_RISE3_SHIFT	3
 #define EXYNOS5440_TMU_INTEN_FALL0_SHIFT	4
-#define EXYNOS5440_TMU_INTEN_FALL1_SHIFT	5
-#define EXYNOS5440_TMU_INTEN_FALL2_SHIFT	6
-#define EXYNOS5440_TMU_INTEN_FALL3_SHIFT	7
-#define EXYNOS5440_TMU_TH_RISE0_SHIFT		0
-#define EXYNOS5440_TMU_TH_RISE1_SHIFT		8
-#define EXYNOS5440_TMU_TH_RISE2_SHIFT		16
-#define EXYNOS5440_TMU_TH_RISE3_SHIFT		24
 #define EXYNOS5440_TMU_TH_RISE4_SHIFT		24
 #define EXYNOS5440_EFUSE_SWAP_OFFSET		8
 
diff --git a/drivers/thermal/thermal_core.c b/drivers/thermal/thermal_core.c
index 9bf10aa6069b..43b90709585f 100644
--- a/drivers/thermal/thermal_core.c
+++ b/drivers/thermal/thermal_core.c
@@ -1575,8 +1575,7 @@ struct thermal_zone_device *thermal_zone_device_register(const char *type,
 
 	thermal_zone_device_update(tz);
 
-	if (!result)
-		return tz;
+	return tz;
 
 unregister:
 	release_idr(&thermal_tz_idr, &thermal_idr_lock, tz->id);