diff --git a/arch/arm/boot/compressed/head.S b/arch/arm/boot/compressed/head.S index 6abafb6f1844..aaa47400eb9c 100644 --- a/arch/arm/boot/compressed/head.S +++ b/arch/arm/boot/compressed/head.S @@ -84,7 +84,7 @@ kputc #'\n' kphex r5, 8 /* decompressed kernel start */ kputc #'-' - kphex r8, 8 /* decompressed kernel end */ + kphex r9, 8 /* decompressed kernel end */ kputc #'>' kphex r4, 8 /* kernel execution address */ kputc #'\n' @@ -116,7 +116,7 @@ start: .word start @ absolute load/run zImage address .word _edata @ zImage end address 1: mov r7, r1 @ save architecture ID - mov r8, #0 @ save r0 + mov r8, r2 @ save atags pointer #ifndef __ARM_ARCH_2__ /* @@ -144,7 +144,7 @@ not_angel: /* * some architecture specific code can be inserted - * by the linker here, but it should preserve r7 and r8. + * by the linker here, but it should preserve r7, r8, and r9. */ .text @@ -249,16 +249,17 @@ not_relocated: mov r0, #0 * r5 = decompressed kernel start * r6 = processor ID * r7 = architecture ID - * r8-r14 = unused + * r8 = atags pointer + * r9-r14 = corrupted */ add r1, r5, r0 @ end of decompressed kernel adr r2, reloc_start ldr r3, LC1 add r3, r2, r3 -1: ldmia r2!, {r8 - r13} @ copy relocation code - stmia r1!, {r8 - r13} - ldmia r2!, {r8 - r13} - stmia r1!, {r8 - r13} +1: ldmia r2!, {r9 - r14} @ copy relocation code + stmia r1!, {r9 - r14} + ldmia r2!, {r9 - r14} + stmia r1!, {r9 - r14} cmp r2, r3 blo 1b @@ -308,11 +309,12 @@ params: ldr r0, =params_phys * r4 = kernel execution address * r6 = processor ID * r7 = architecture number - * r8 = run-time address of "start" + * r8 = atags pointer + * r9 = run-time address of "start" (???) * On exit, - * r1, r2, r3, r8, r9, r12 corrupted + * r1, r2, r3, r9, r10, r12 corrupted * This routine must preserve: - * r4, r5, r6, r7 + * r4, r5, r6, r7, r8 */ .align 5 cache_on: mov r3, #8 @ cache_on function @@ -326,15 +328,15 @@ __setup_mmu: sub r3, r4, #16384 @ Page directory size * bits for the RAM area only. */ mov r0, r3 - mov r8, r0, lsr #18 - mov r8, r8, lsl #18 @ start of RAM - add r9, r8, #0x10000000 @ a reasonable RAM size + mov r9, r0, lsr #18 + mov r9, r9, lsl #18 @ start of RAM + add r10, r9, #0x10000000 @ a reasonable RAM size mov r1, #0x12 orr r1, r1, #3 << 10 add r2, r3, #16384 1: cmp r1, r8 @ if virt > start of RAM orrhs r1, r1, #0x0c @ set cacheable, bufferable - cmp r1, r9 @ if virt > end of RAM + cmp r1, r10 @ if virt > end of RAM bichs r1, r1, #0x0c @ clear cacheable, bufferable str r1, [r0], #4 @ 1:1 mapping add r1, r1, #1048576 @@ -403,26 +405,28 @@ __common_cache_on: * r5 = decompressed kernel start * r6 = processor ID * r7 = architecture ID - * r8-r14 = unused + * r8 = atags pointer + * r9-r14 = corrupted */ .align 5 -reloc_start: add r8, r5, r0 +reloc_start: add r9, r5, r0 debug_reloc_start mov r1, r4 1: .rept 4 - ldmia r5!, {r0, r2, r3, r9 - r13} @ relocate kernel - stmia r1!, {r0, r2, r3, r9 - r13} + ldmia r5!, {r0, r2, r3, r10 - r14} @ relocate kernel + stmia r1!, {r0, r2, r3, r10 - r14} .endr - cmp r5, r8 + cmp r5, r9 blo 1b debug_reloc_end call_kernel: bl cache_clean_flush bl cache_off - mov r0, #0 + mov r0, #0 @ must be zero mov r1, r7 @ restore architecture number + mov r2, r8 @ restore atags pointer mov pc, r4 @ call kernel /* diff --git a/arch/arm/common/rtctime.c b/arch/arm/common/rtctime.c index ffb82d5bedef..48b1e19b131f 100644 --- a/arch/arm/common/rtctime.c +++ b/arch/arm/common/rtctime.c @@ -19,6 +19,7 @@ #include #include #include +#include #include #include @@ -35,7 +36,7 @@ static unsigned long rtc_irq_data; /* * rtc_sem protects rtc_inuse and rtc_ops */ -static DECLARE_MUTEX(rtc_sem); +static DEFINE_MUTEX(rtc_mutex); static unsigned long rtc_inuse; static struct rtc_ops *rtc_ops; @@ -356,7 +357,7 @@ static int rtc_open(struct inode *inode, struct file *file) { int ret; - down(&rtc_sem); + mutex_lock(&rtc_mutex); if (rtc_inuse) { ret = -EBUSY; @@ -374,7 +375,7 @@ static int rtc_open(struct inode *inode, struct file *file) rtc_inuse = 1; } } - up(&rtc_sem); + mutex_unlock(&rtc_mutex); return ret; } @@ -480,7 +481,7 @@ int register_rtc(struct rtc_ops *ops) { int ret = -EBUSY; - down(&rtc_sem); + mutex_lock(&rtc_mutex); if (rtc_ops == NULL) { rtc_ops = ops; @@ -489,7 +490,7 @@ int register_rtc(struct rtc_ops *ops) create_proc_read_entry("driver/rtc", 0, NULL, rtc_read_proc, ops); } - up(&rtc_sem); + mutex_unlock(&rtc_mutex); return ret; } @@ -497,12 +498,12 @@ EXPORT_SYMBOL(register_rtc); void unregister_rtc(struct rtc_ops *rtc) { - down(&rtc_sem); + mutex_lock(&rtc_mutex); if (rtc == rtc_ops) { remove_proc_entry("driver/rtc", NULL); misc_deregister(&rtc_miscdev); rtc_ops = NULL; } - up(&rtc_sem); + mutex_unlock(&rtc_mutex); } EXPORT_SYMBOL(unregister_rtc); diff --git a/arch/arm/configs/at91rm9200dk_defconfig b/arch/arm/configs/at91rm9200dk_defconfig new file mode 100644 index 000000000000..5cdd13acf8ff --- /dev/null +++ b/arch/arm/configs/at91rm9200dk_defconfig @@ -0,0 +1,1009 @@ +# +# Automatically generated make config: don't edit +# Linux kernel version: 2.6.15 +# Mon Jan 9 20:54:30 2006 +# +CONFIG_ARM=y +CONFIG_MMU=y +CONFIG_UID16=y +CONFIG_RWSEM_GENERIC_SPINLOCK=y +CONFIG_GENERIC_CALIBRATE_DELAY=y + +# +# Code maturity level options +# +CONFIG_EXPERIMENTAL=y +CONFIG_CLEAN_COMPILE=y +CONFIG_BROKEN_ON_SMP=y +CONFIG_INIT_ENV_ARG_LIMIT=32 + +# +# General setup +# +CONFIG_LOCALVERSION="" +CONFIG_LOCALVERSION_AUTO=y +# CONFIG_SWAP is not set +CONFIG_SYSVIPC=y +# CONFIG_POSIX_MQUEUE is not set +# CONFIG_BSD_PROCESS_ACCT is not set +CONFIG_SYSCTL=y +# CONFIG_AUDIT is not set +CONFIG_HOTPLUG=y +CONFIG_KOBJECT_UEVENT=y +# CONFIG_IKCONFIG is not set +CONFIG_INITRAMFS_SOURCE="" +CONFIG_CC_OPTIMIZE_FOR_SIZE=y +# CONFIG_EMBEDDED is not set +CONFIG_KALLSYMS=y +# CONFIG_KALLSYMS_ALL is not set +# CONFIG_KALLSYMS_EXTRA_PASS is not set +CONFIG_PRINTK=y +CONFIG_BUG=y +CONFIG_BASE_FULL=y +CONFIG_FUTEX=y +CONFIG_EPOLL=y +CONFIG_SHMEM=y +CONFIG_CC_ALIGN_FUNCTIONS=0 +CONFIG_CC_ALIGN_LABELS=0 +CONFIG_CC_ALIGN_LOOPS=0 +CONFIG_CC_ALIGN_JUMPS=0 +# CONFIG_TINY_SHMEM is not set +CONFIG_BASE_SMALL=0 + +# +# Loadable module support +# +CONFIG_MODULES=y +CONFIG_MODULE_UNLOAD=y +# CONFIG_MODULE_FORCE_UNLOAD is not set +CONFIG_OBSOLETE_MODPARM=y +# CONFIG_MODVERSIONS is not set +# CONFIG_MODULE_SRCVERSION_ALL is not set +CONFIG_KMOD=y + +# +# Block layer +# + +# +# IO Schedulers +# +CONFIG_IOSCHED_NOOP=y +CONFIG_IOSCHED_AS=y +# CONFIG_IOSCHED_DEADLINE is not set +# CONFIG_IOSCHED_CFQ is not set +CONFIG_DEFAULT_AS=y +# CONFIG_DEFAULT_DEADLINE is not set +# CONFIG_DEFAULT_CFQ is not set +# CONFIG_DEFAULT_NOOP is not set +CONFIG_DEFAULT_IOSCHED="anticipatory" + +# +# System Type +# +# CONFIG_ARCH_CLPS7500 is not set +# CONFIG_ARCH_CLPS711X is not set +# CONFIG_ARCH_CO285 is not set +# CONFIG_ARCH_EBSA110 is not set +# CONFIG_ARCH_CAMELOT is not set +# CONFIG_ARCH_FOOTBRIDGE is not set +# CONFIG_ARCH_INTEGRATOR is not set +# CONFIG_ARCH_IOP3XX is not set +# CONFIG_ARCH_IXP4XX is not set +# CONFIG_ARCH_IXP2000 is not set +# CONFIG_ARCH_L7200 is not set +# CONFIG_ARCH_PXA is not set +# CONFIG_ARCH_RPC is not set +# CONFIG_ARCH_SA1100 is not set +# CONFIG_ARCH_S3C2410 is not set +# CONFIG_ARCH_SHARK is not set +# CONFIG_ARCH_LH7A40X is not set +# CONFIG_ARCH_OMAP is not set +# CONFIG_ARCH_VERSATILE is not set +# CONFIG_ARCH_REALVIEW is not set +# CONFIG_ARCH_IMX is not set +# CONFIG_ARCH_H720X is not set +# CONFIG_ARCH_AAEC2000 is not set +CONFIG_ARCH_AT91RM9200=y + +# +# AT91RM9200 Implementations +# + +# +# AT91RM9200 Board Type +# +CONFIG_ARCH_AT91RM9200DK=y +# CONFIG_MACH_AT91RM9200EK is not set +# CONFIG_MACH_CSB337 is not set +# CONFIG_MACH_CSB637 is not set +# CONFIG_MACH_CARMEVA is not set +# CONFIG_MACH_KB9200 is not set +# CONFIG_MACH_ATEB9200 is not set + +# +# AT91RM9200 Feature Selections +# +CONFIG_AT91_PROGRAMMABLE_CLOCKS=y + +# +# Processor Type +# +CONFIG_CPU_32=y +CONFIG_CPU_ARM920T=y +CONFIG_CPU_32v4=y +CONFIG_CPU_ABRT_EV4T=y +CONFIG_CPU_CACHE_V4WT=y +CONFIG_CPU_CACHE_VIVT=y +CONFIG_CPU_COPY_V4WB=y +CONFIG_CPU_TLB_V4WBI=y + +# +# Processor Features +# +# CONFIG_ARM_THUMB is not set +# CONFIG_CPU_ICACHE_DISABLE is not set +# CONFIG_CPU_DCACHE_DISABLE is not set +# CONFIG_CPU_DCACHE_WRITETHROUGH is not set + +# +# Bus support +# +CONFIG_ISA_DMA_API=y + +# +# PCCARD (PCMCIA/CardBus) support +# +CONFIG_PCCARD=y +# CONFIG_PCMCIA_DEBUG is not set +CONFIG_PCMCIA=y +CONFIG_PCMCIA_LOAD_CIS=y +CONFIG_PCMCIA_IOCTL=y + +# +# PC-card bridges +# +CONFIG_AT91_CF=y + +# +# Kernel Features +# +# CONFIG_PREEMPT is not set +# CONFIG_NO_IDLE_HZ is not set +# CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set +CONFIG_SELECT_MEMORY_MODEL=y +CONFIG_FLATMEM_MANUAL=y +# CONFIG_DISCONTIGMEM_MANUAL is not set +# CONFIG_SPARSEMEM_MANUAL is not set +CONFIG_FLATMEM=y +CONFIG_FLAT_NODE_MEM_MAP=y +# CONFIG_SPARSEMEM_STATIC is not set +CONFIG_SPLIT_PTLOCK_CPUS=4096 +CONFIG_LEDS=y +CONFIG_LEDS_TIMER=y +# CONFIG_LEDS_CPU is not set +CONFIG_ALIGNMENT_TRAP=y + +# +# Boot options +# +CONFIG_ZBOOT_ROM_TEXT=0x0 +CONFIG_ZBOOT_ROM_BSS=0x0 +CONFIG_CMDLINE="mem=32M console=ttyS0,115200 initrd=0x20410000,3145728 root=/dev/ram0 rw" +# CONFIG_XIP_KERNEL is not set + +# +# Floating point emulation +# + +# +# At least one emulation must be selected +# +CONFIG_FPE_NWFPE=y +# CONFIG_FPE_NWFPE_XP is not set +# CONFIG_FPE_FASTFPE is not set + +# +# Userspace binary formats +# +CONFIG_BINFMT_ELF=y +# CONFIG_BINFMT_AOUT is not set +# CONFIG_BINFMT_MISC is not set +# CONFIG_ARTHUR is not set + +# +# Power management options +# +# CONFIG_PM is not set + +# +# Networking +# +CONFIG_NET=y + +# +# Networking options +# +CONFIG_PACKET=y +# CONFIG_PACKET_MMAP is not set +CONFIG_UNIX=y +# CONFIG_NET_KEY is not set +CONFIG_INET=y +# CONFIG_IP_MULTICAST is not set +# CONFIG_IP_ADVANCED_ROUTER is not set +CONFIG_IP_FIB_HASH=y +CONFIG_IP_PNP=y +# CONFIG_IP_PNP_DHCP is not set +CONFIG_IP_PNP_BOOTP=y +# CONFIG_IP_PNP_RARP is not set +# CONFIG_NET_IPIP is not set +# CONFIG_NET_IPGRE is not set +# CONFIG_ARPD is not set +# CONFIG_SYN_COOKIES is not set +# CONFIG_INET_AH is not set +# CONFIG_INET_ESP is not set +# CONFIG_INET_IPCOMP is not set +# CONFIG_INET_TUNNEL is not set +CONFIG_INET_DIAG=y +CONFIG_INET_TCP_DIAG=y +# CONFIG_TCP_CONG_ADVANCED is not set +CONFIG_TCP_CONG_BIC=y +# CONFIG_IPV6 is not set +# CONFIG_NETFILTER is not set + +# +# DCCP Configuration (EXPERIMENTAL) +# +# CONFIG_IP_DCCP is not set + +# +# SCTP Configuration (EXPERIMENTAL) +# +# CONFIG_IP_SCTP is not set +# CONFIG_ATM is not set +# CONFIG_BRIDGE is not set +# CONFIG_VLAN_8021Q is not set +# CONFIG_DECNET is not set +# CONFIG_LLC2 is not set +# CONFIG_IPX is not set +# CONFIG_ATALK is not set +# CONFIG_X25 is not set +# CONFIG_LAPB is not set +# CONFIG_NET_DIVERT is not set +# CONFIG_ECONET is not set +# CONFIG_WAN_ROUTER is not set + +# +# QoS and/or fair queueing +# +# CONFIG_NET_SCHED is not set + +# +# Network testing +# +# CONFIG_NET_PKTGEN is not set +# CONFIG_HAMRADIO is not set +# CONFIG_IRDA is not set +# CONFIG_BT is not set +# CONFIG_IEEE80211 is not set + +# +# Device Drivers +# + +# +# Generic Driver Options +# +CONFIG_STANDALONE=y +CONFIG_PREVENT_FIRMWARE_BUILD=y +CONFIG_FW_LOADER=y +# CONFIG_DEBUG_DRIVER is not set + +# +# Connector - unified userspace <-> kernelspace linker +# +# CONFIG_CONNECTOR is not set + +# +# Memory Technology Devices (MTD) +# +CONFIG_MTD=y +# CONFIG_MTD_DEBUG is not set +# CONFIG_MTD_CONCAT is not set +CONFIG_MTD_PARTITIONS=y +# CONFIG_MTD_REDBOOT_PARTS is not set +CONFIG_MTD_CMDLINE_PARTS=y +# CONFIG_MTD_AFS_PARTS is not set + +# +# User Modules And Translation Layers +# +CONFIG_MTD_CHAR=y +CONFIG_MTD_BLOCK=y +# CONFIG_FTL is not set +# CONFIG_NFTL is not set +# CONFIG_INFTL is not set +# CONFIG_RFD_FTL is not set + +# +# RAM/ROM/Flash chip drivers +# +CONFIG_MTD_CFI=y +CONFIG_MTD_JEDECPROBE=y +CONFIG_MTD_GEN_PROBE=y +# CONFIG_MTD_CFI_ADV_OPTIONS is not set +CONFIG_MTD_MAP_BANK_WIDTH_1=y +CONFIG_MTD_MAP_BANK_WIDTH_2=y +CONFIG_MTD_MAP_BANK_WIDTH_4=y +# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set +CONFIG_MTD_CFI_I1=y +CONFIG_MTD_CFI_I2=y +# CONFIG_MTD_CFI_I4 is not set +# CONFIG_MTD_CFI_I8 is not set +# CONFIG_MTD_CFI_INTELEXT is not set +CONFIG_MTD_CFI_AMDSTD=y +CONFIG_MTD_CFI_AMDSTD_RETRY=0 +# CONFIG_MTD_CFI_STAA is not set +CONFIG_MTD_CFI_UTIL=y +# CONFIG_MTD_RAM is not set +# CONFIG_MTD_ROM is not set +# CONFIG_MTD_ABSENT is not set +# CONFIG_MTD_XIP is not set + +# +# Mapping drivers for chip access +# +# CONFIG_MTD_COMPLEX_MAPPINGS is not set +CONFIG_MTD_PHYSMAP=y +CONFIG_MTD_PHYSMAP_START=0x10000000 +CONFIG_MTD_PHYSMAP_LEN=0x200000 +CONFIG_MTD_PHYSMAP_BANKWIDTH=2 +# CONFIG_MTD_ARM_INTEGRATOR is not set +# CONFIG_MTD_IMPA7 is not set +# CONFIG_MTD_PLATRAM is not set + +# +# Self-contained MTD device drivers +# +# CONFIG_MTD_SLRAM is not set +# CONFIG_MTD_PHRAM is not set +# CONFIG_MTD_MTDRAM is not set +# CONFIG_MTD_BLKMTD is not set +# CONFIG_MTD_BLOCK2MTD is not set + +# +# Disk-On-Chip Device Drivers +# +# CONFIG_MTD_DOC2000 is not set +# CONFIG_MTD_DOC2001 is not set +# CONFIG_MTD_DOC2001PLUS is not set +CONFIG_MTD_AT91_DATAFLASH=y +CONFIG_MTD_AT91_DATAFLASH_CARD=y + +# +# NAND Flash Device Drivers +# +# CONFIG_MTD_NAND is not set + +# +# OneNAND Flash Device Drivers +# +# CONFIG_MTD_ONENAND is not set + +# +# Parallel port support +# +# CONFIG_PARPORT is not set + +# +# Plug and Play support +# + +# +# Block devices +# +# CONFIG_BLK_DEV_COW_COMMON is not set +# CONFIG_BLK_DEV_LOOP is not set +# CONFIG_BLK_DEV_NBD is not set +# CONFIG_BLK_DEV_UB is not set +CONFIG_BLK_DEV_RAM=y +CONFIG_BLK_DEV_RAM_COUNT=16 +CONFIG_BLK_DEV_RAM_SIZE=8192 +CONFIG_BLK_DEV_INITRD=y +# CONFIG_CDROM_PKTCDVD is not set +# CONFIG_ATA_OVER_ETH is not set + +# +# ATA/ATAPI/MFM/RLL support +# +# CONFIG_IDE is not set + +# +# SCSI device support +# +# CONFIG_RAID_ATTRS is not set +# CONFIG_SCSI is not set + +# +# Multi-device support (RAID and LVM) +# +# CONFIG_MD is not set + +# +# Fusion MPT device support +# +# CONFIG_FUSION is not set + +# +# IEEE 1394 (FireWire) support +# + +# +# I2O device support +# + +# +# Network device support +# +CONFIG_NETDEVICES=y +# CONFIG_DUMMY is not set +# CONFIG_BONDING is not set +# CONFIG_EQUALIZER is not set +# CONFIG_TUN is not set + +# +# PHY device support +# +# CONFIG_PHYLIB is not set + +# +# Ethernet (10 or 100Mbit) +# +CONFIG_NET_ETHERNET=y +CONFIG_MII=y +CONFIG_ARM_AT91_ETHER=y +# CONFIG_SMC91X is not set +# CONFIG_DM9000 is not set + +# +# Ethernet (1000 Mbit) +# + +# +# Ethernet (10000 Mbit) +# + +# +# Token Ring devices +# + +# +# Wireless LAN (non-hamradio) +# +# CONFIG_NET_RADIO is not set + +# +# PCMCIA network device support +# +# CONFIG_NET_PCMCIA is not set + +# +# Wan interfaces +# +# CONFIG_WAN is not set +# CONFIG_PPP is not set +# CONFIG_SLIP is not set +# CONFIG_SHAPER is not set +# CONFIG_NETCONSOLE is not set +# CONFIG_NETPOLL is not set +# CONFIG_NET_POLL_CONTROLLER is not set + +# +# ISDN subsystem +# +# CONFIG_ISDN is not set + +# +# Input device support +# +CONFIG_INPUT=y + +# +# Userland interfaces +# +CONFIG_INPUT_MOUSEDEV=y +# CONFIG_INPUT_MOUSEDEV_PSAUX is not set +CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024 +CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 +# CONFIG_INPUT_JOYDEV is not set +# CONFIG_INPUT_TSDEV is not set +# CONFIG_INPUT_EVDEV is not set +# CONFIG_INPUT_EVBUG is not set + +# +# Input Device Drivers +# +# CONFIG_INPUT_KEYBOARD is not set +# CONFIG_INPUT_MOUSE is not set +# CONFIG_INPUT_JOYSTICK is not set +# CONFIG_INPUT_TOUCHSCREEN is not set +# CONFIG_INPUT_MISC is not set + +# +# Hardware I/O ports +# +# CONFIG_SERIO is not set +# CONFIG_GAMEPORT is not set + +# +# Character devices +# +CONFIG_VT=y +CONFIG_VT_CONSOLE=y +CONFIG_HW_CONSOLE=y +# CONFIG_SERIAL_NONSTANDARD is not set + +# +# Serial drivers +# +# CONFIG_SERIAL_8250 is not set + +# +# Non-8250 serial port support +# +CONFIG_SERIAL_AT91=y +CONFIG_SERIAL_AT91_CONSOLE=y +# CONFIG_SERIAL_AT91_TTYAT is not set +CONFIG_SERIAL_CORE=y +CONFIG_SERIAL_CORE_CONSOLE=y +CONFIG_UNIX98_PTYS=y +CONFIG_LEGACY_PTYS=y +CONFIG_LEGACY_PTY_COUNT=256 + +# +# IPMI +# +# CONFIG_IPMI_HANDLER is not set + +# +# Watchdog Cards +# +CONFIG_WATCHDOG=y +CONFIG_WATCHDOG_NOWAYOUT=y + +# +# Watchdog Device Drivers +# +# CONFIG_SOFT_WATCHDOG is not set +CONFIG_AT91_WATCHDOG=y + +# +# USB-based Watchdog Cards +# +# CONFIG_USBPCWATCHDOG is not set +# CONFIG_NVRAM is not set +# CONFIG_RTC is not set +CONFIG_AT91_RTC=y +# CONFIG_DTLK is not set +# CONFIG_R3964 is not set + +# +# Ftape, the floppy tape device driver +# + +# +# PCMCIA character devices +# +# CONFIG_SYNCLINK_CS is not set +# CONFIG_CARDMAN_4000 is not set +# CONFIG_CARDMAN_4040 is not set +# CONFIG_RAW_DRIVER is not set + +# +# TPM devices +# +# CONFIG_TCG_TPM is not set +# CONFIG_TELCLOCK is not set +CONFIG_AT91_SPI=y +CONFIG_AT91_SPIDEV=y + +# +# I2C support +# +CONFIG_I2C=y +CONFIG_I2C_CHARDEV=y + +# +# I2C Algorithms +# +# CONFIG_I2C_ALGOBIT is not set +# CONFIG_I2C_ALGOPCF is not set +# CONFIG_I2C_ALGOPCA is not set + +# +# I2C Hardware Bus support +# +CONFIG_I2C_AT91=y +# CONFIG_I2C_PARPORT_LIGHT is not set +# CONFIG_I2C_STUB is not set +# CONFIG_I2C_PCA_ISA is not set + +# +# Miscellaneous I2C Chip support +# +# CONFIG_SENSORS_DS1337 is not set +# CONFIG_SENSORS_DS1374 is not set +# CONFIG_SENSORS_EEPROM is not set +# CONFIG_SENSORS_PCF8574 is not set +# CONFIG_SENSORS_PCA9539 is not set +# CONFIG_SENSORS_PCF8591 is not set +# CONFIG_SENSORS_RTC8564 is not set +# CONFIG_SENSORS_MAX6875 is not set +# CONFIG_RTC_X1205_I2C is not set +# CONFIG_I2C_DEBUG_CORE is not set +# CONFIG_I2C_DEBUG_ALGO is not set +# CONFIG_I2C_DEBUG_BUS is not set +# CONFIG_I2C_DEBUG_CHIP is not set + +# +# Hardware Monitoring support +# +CONFIG_HWMON=y +# CONFIG_HWMON_VID is not set +# CONFIG_SENSORS_ADM1021 is not set +# CONFIG_SENSORS_ADM1025 is not set +# CONFIG_SENSORS_ADM1026 is not set +# CONFIG_SENSORS_ADM1031 is not set +# CONFIG_SENSORS_ADM9240 is not set +# CONFIG_SENSORS_ASB100 is not set +# CONFIG_SENSORS_ATXP1 is not set +# CONFIG_SENSORS_DS1621 is not set +# CONFIG_SENSORS_FSCHER is not set +# CONFIG_SENSORS_FSCPOS is not set +# CONFIG_SENSORS_GL518SM is not set +# CONFIG_SENSORS_GL520SM is not set +# CONFIG_SENSORS_IT87 is not set +# CONFIG_SENSORS_LM63 is not set +# CONFIG_SENSORS_LM75 is not set +# CONFIG_SENSORS_LM77 is not set +# CONFIG_SENSORS_LM78 is not set +# CONFIG_SENSORS_LM80 is not set +# CONFIG_SENSORS_LM83 is not set +# CONFIG_SENSORS_LM85 is not set +# CONFIG_SENSORS_LM87 is not set +# CONFIG_SENSORS_LM90 is not set +# CONFIG_SENSORS_LM92 is not set +# CONFIG_SENSORS_MAX1619 is not set +# CONFIG_SENSORS_PC87360 is not set +# CONFIG_SENSORS_SMSC47M1 is not set +# CONFIG_SENSORS_SMSC47B397 is not set +# CONFIG_SENSORS_W83781D is not set +# CONFIG_SENSORS_W83792D is not set +# CONFIG_SENSORS_W83L785TS is not set +# CONFIG_SENSORS_W83627HF is not set +# CONFIG_SENSORS_W83627EHF is not set +# CONFIG_HWMON_DEBUG_CHIP is not set + +# +# Misc devices +# + +# +# Multimedia Capabilities Port drivers +# + +# +# Multimedia devices +# +# CONFIG_VIDEO_DEV is not set + +# +# Digital Video Broadcasting Devices +# +# CONFIG_DVB is not set + +# +# Graphics support +# +# CONFIG_FB is not set + +# +# Console display driver support +# +# CONFIG_VGA_CONSOLE is not set +CONFIG_DUMMY_CONSOLE=y + +# +# Sound +# +# CONFIG_SOUND is not set + +# +# USB support +# +CONFIG_USB_ARCH_HAS_HCD=y +CONFIG_USB_ARCH_HAS_OHCI=y +CONFIG_USB=y +CONFIG_USB_DEBUG=y + +# +# Miscellaneous USB options +# +CONFIG_USB_DEVICEFS=y +# CONFIG_USB_BANDWIDTH is not set +# CONFIG_USB_DYNAMIC_MINORS is not set +# CONFIG_USB_OTG is not set + +# +# USB Host Controller Drivers +# +# CONFIG_USB_ISP116X_HCD is not set +CONFIG_USB_OHCI_HCD=y +# CONFIG_USB_OHCI_BIG_ENDIAN is not set +CONFIG_USB_OHCI_LITTLE_ENDIAN=y +# CONFIG_USB_SL811_HCD is not set + +# +# USB Device Class drivers +# +# CONFIG_USB_ACM is not set +# CONFIG_USB_PRINTER is not set + +# +# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' +# + +# +# may also be needed; see USB_STORAGE Help for more information +# +# CONFIG_USB_STORAGE is not set + +# +# USB Input Devices +# +# CONFIG_USB_HID is not set + +# +# USB HID Boot Protocol drivers +# +# CONFIG_USB_KBD is not set +# CONFIG_USB_MOUSE is not set +# CONFIG_USB_AIPTEK is not set +# CONFIG_USB_WACOM is not set +# CONFIG_USB_ACECAD is not set +# CONFIG_USB_KBTAB is not set +# CONFIG_USB_POWERMATE is not set +# CONFIG_USB_MTOUCH is not set +# CONFIG_USB_ITMTOUCH is not set +# CONFIG_USB_EGALAX is not set +# CONFIG_USB_YEALINK is not set +# CONFIG_USB_XPAD is not set +# CONFIG_USB_ATI_REMOTE is not set +# CONFIG_USB_KEYSPAN_REMOTE is not set +# CONFIG_USB_APPLETOUCH is not set + +# +# USB Imaging devices +# +# CONFIG_USB_MDC800 is not set + +# +# USB Multimedia devices +# +# CONFIG_USB_DABUSB is not set + +# +# Video4Linux support is needed for USB Multimedia device support +# + +# +# USB Network Adapters +# +# CONFIG_USB_CATC is not set +# CONFIG_USB_KAWETH is not set +# CONFIG_USB_PEGASUS is not set +# CONFIG_USB_RTL8150 is not set +# CONFIG_USB_USBNET is not set +CONFIG_USB_MON=y + +# +# USB port drivers +# + +# +# USB Serial Converter support +# +# CONFIG_USB_SERIAL is not set + +# +# USB Miscellaneous drivers +# +# CONFIG_USB_EMI62 is not set +# CONFIG_USB_EMI26 is not set +# CONFIG_USB_AUERSWALD is not set +# CONFIG_USB_RIO500 is not set +# CONFIG_USB_LEGOTOWER is not set +# CONFIG_USB_LCD is not set +# CONFIG_USB_LED is not set +# CONFIG_USB_CYTHERM is not set +# CONFIG_USB_PHIDGETKIT is not set +# CONFIG_USB_PHIDGETSERVO is not set +# CONFIG_USB_IDMOUSE is not set +# CONFIG_USB_LD is not set +# CONFIG_USB_TEST is not set + +# +# USB DSL modem support +# + +# +# USB Gadget Support +# +CONFIG_USB_GADGET=y +# CONFIG_USB_GADGET_DEBUG_FILES is not set +CONFIG_USB_GADGET_SELECTED=y +# CONFIG_USB_GADGET_NET2280 is not set +# CONFIG_USB_GADGET_PXA2XX is not set +# CONFIG_USB_GADGET_GOKU is not set +# CONFIG_USB_GADGET_LH7A40X is not set +# CONFIG_USB_GADGET_OMAP is not set +CONFIG_USB_GADGET_AT91=y +CONFIG_USB_AT91=y +# CONFIG_USB_GADGET_DUMMY_HCD is not set +# CONFIG_USB_GADGET_DUALSPEED is not set +# CONFIG_USB_ZERO is not set +# CONFIG_USB_ETH is not set +# CONFIG_USB_GADGETFS is not set +# CONFIG_USB_FILE_STORAGE is not set +# CONFIG_USB_G_SERIAL is not set + +# +# MMC/SD Card support +# +CONFIG_MMC=y +# CONFIG_MMC_DEBUG is not set +CONFIG_MMC_BLOCK=y +# CONFIG_MMC_WBSD is not set +CONFIG_MMC_AT91RM9200=y + +# +# File systems +# +CONFIG_EXT2_FS=y +# CONFIG_EXT2_FS_XATTR is not set +# CONFIG_EXT2_FS_XIP is not set +# CONFIG_EXT3_FS is not set +# CONFIG_JBD is not set +# CONFIG_REISERFS_FS is not set +# CONFIG_JFS_FS is not set +# CONFIG_FS_POSIX_ACL is not set +# CONFIG_XFS_FS is not set +# CONFIG_MINIX_FS is not set +# CONFIG_ROMFS_FS is not set +CONFIG_INOTIFY=y +# CONFIG_QUOTA is not set +CONFIG_DNOTIFY=y +# CONFIG_AUTOFS_FS is not set +# CONFIG_AUTOFS4_FS is not set +# CONFIG_FUSE_FS is not set + +# +# CD-ROM/DVD Filesystems +# +# CONFIG_ISO9660_FS is not set +# CONFIG_UDF_FS is not set + +# +# DOS/FAT/NT Filesystems +# +# CONFIG_MSDOS_FS is not set +# CONFIG_VFAT_FS is not set +# CONFIG_NTFS_FS is not set + +# +# Pseudo filesystems +# +CONFIG_PROC_FS=y +CONFIG_SYSFS=y +CONFIG_TMPFS=y +# CONFIG_HUGETLB_PAGE is not set +CONFIG_RAMFS=y +# CONFIG_RELAYFS_FS is not set + +# +# Miscellaneous filesystems +# +# CONFIG_ADFS_FS is not set +# CONFIG_AFFS_FS is not set +# CONFIG_HFS_FS is not set +# CONFIG_HFSPLUS_FS is not set +# CONFIG_BEFS_FS is not set +# CONFIG_BFS_FS is not set +# CONFIG_EFS_FS is not set +# CONFIG_JFFS_FS is not set +# CONFIG_JFFS2_FS is not set +CONFIG_CRAMFS=y +# CONFIG_VXFS_FS is not set +# CONFIG_HPFS_FS is not set +# CONFIG_QNX4FS_FS is not set +# CONFIG_SYSV_FS is not set +# CONFIG_UFS_FS is not set + +# +# Network File Systems +# +# CONFIG_NFS_FS is not set +# CONFIG_NFSD is not set +# CONFIG_SMB_FS is not set +# CONFIG_CIFS is not set +# CONFIG_NCP_FS is not set +# CONFIG_CODA_FS is not set +# CONFIG_AFS_FS is not set +# CONFIG_9P_FS is not set + +# +# Partition Types +# +# CONFIG_PARTITION_ADVANCED is not set +CONFIG_MSDOS_PARTITION=y + +# +# Native Language Support +# +# CONFIG_NLS is not set + +# +# Profiling support +# +# CONFIG_PROFILING is not set + +# +# Kernel hacking +# +# CONFIG_PRINTK_TIME is not set +CONFIG_DEBUG_KERNEL=y +# CONFIG_MAGIC_SYSRQ is not set +CONFIG_LOG_BUF_SHIFT=14 +CONFIG_DETECT_SOFTLOCKUP=y +# CONFIG_SCHEDSTATS is not set +# CONFIG_DEBUG_SLAB is not set +# CONFIG_DEBUG_SPINLOCK is not set +# CONFIG_DEBUG_SPINLOCK_SLEEP is not set +# CONFIG_DEBUG_KOBJECT is not set +CONFIG_DEBUG_BUGVERBOSE=y +# CONFIG_DEBUG_INFO is not set +# CONFIG_DEBUG_FS is not set +# CONFIG_DEBUG_VM is not set +CONFIG_FRAME_POINTER=y +# CONFIG_RCU_TORTURE_TEST is not set +CONFIG_DEBUG_USER=y +# CONFIG_DEBUG_WAITQ is not set +# CONFIG_DEBUG_ERRORS is not set +CONFIG_DEBUG_LL=y +# CONFIG_DEBUG_ICEDCC is not set + +# +# Security options +# +# CONFIG_KEYS is not set +# CONFIG_SECURITY is not set + +# +# Cryptographic options +# +# CONFIG_CRYPTO is not set + +# +# Hardware crypto devices +# + +# +# Library routines +# +# CONFIG_CRC_CCITT is not set +# CONFIG_CRC16 is not set +CONFIG_CRC32=y +# CONFIG_LIBCRC32C is not set +CONFIG_ZLIB_INFLATE=y diff --git a/arch/arm/configs/at91rm9200ek_defconfig b/arch/arm/configs/at91rm9200ek_defconfig new file mode 100644 index 000000000000..20838ccf1da7 --- /dev/null +++ b/arch/arm/configs/at91rm9200ek_defconfig @@ -0,0 +1,998 @@ +# +# Automatically generated make config: don't edit +# Linux kernel version: 2.6.15 +# Mon Jan 9 20:57:31 2006 +# +CONFIG_ARM=y +CONFIG_MMU=y +CONFIG_UID16=y +CONFIG_RWSEM_GENERIC_SPINLOCK=y +CONFIG_GENERIC_CALIBRATE_DELAY=y + +# +# Code maturity level options +# +CONFIG_EXPERIMENTAL=y +CONFIG_CLEAN_COMPILE=y +CONFIG_BROKEN_ON_SMP=y +CONFIG_INIT_ENV_ARG_LIMIT=32 + +# +# General setup +# +CONFIG_LOCALVERSION="" +# CONFIG_LOCALVERSION_AUTO is not set +# CONFIG_SWAP is not set +CONFIG_SYSVIPC=y +# CONFIG_POSIX_MQUEUE is not set +# CONFIG_BSD_PROCESS_ACCT is not set +CONFIG_SYSCTL=y +# CONFIG_AUDIT is not set +CONFIG_HOTPLUG=y +CONFIG_KOBJECT_UEVENT=y +# CONFIG_IKCONFIG is not set +CONFIG_INITRAMFS_SOURCE="" +CONFIG_CC_OPTIMIZE_FOR_SIZE=y +# CONFIG_EMBEDDED is not set +CONFIG_KALLSYMS=y +# CONFIG_KALLSYMS_ALL is not set +# CONFIG_KALLSYMS_EXTRA_PASS is not set +CONFIG_PRINTK=y +CONFIG_BUG=y +CONFIG_BASE_FULL=y +CONFIG_FUTEX=y +CONFIG_EPOLL=y +CONFIG_SHMEM=y +CONFIG_CC_ALIGN_FUNCTIONS=0 +CONFIG_CC_ALIGN_LABELS=0 +CONFIG_CC_ALIGN_LOOPS=0 +CONFIG_CC_ALIGN_JUMPS=0 +# CONFIG_TINY_SHMEM is not set +CONFIG_BASE_SMALL=0 + +# +# Loadable module support +# +CONFIG_MODULES=y +CONFIG_MODULE_UNLOAD=y +# CONFIG_MODULE_FORCE_UNLOAD is not set +CONFIG_OBSOLETE_MODPARM=y +# CONFIG_MODVERSIONS is not set +# CONFIG_MODULE_SRCVERSION_ALL is not set +CONFIG_KMOD=y + +# +# Block layer +# + +# +# IO Schedulers +# +CONFIG_IOSCHED_NOOP=y +CONFIG_IOSCHED_AS=y +# CONFIG_IOSCHED_DEADLINE is not set +# CONFIG_IOSCHED_CFQ is not set +CONFIG_DEFAULT_AS=y +# CONFIG_DEFAULT_DEADLINE is not set +# CONFIG_DEFAULT_CFQ is not set +# CONFIG_DEFAULT_NOOP is not set +CONFIG_DEFAULT_IOSCHED="anticipatory" + +# +# System Type +# +# CONFIG_ARCH_CLPS7500 is not set +# CONFIG_ARCH_CLPS711X is not set +# CONFIG_ARCH_CO285 is not set +# CONFIG_ARCH_EBSA110 is not set +# CONFIG_ARCH_CAMELOT is not set +# CONFIG_ARCH_FOOTBRIDGE is not set +# CONFIG_ARCH_INTEGRATOR is not set +# CONFIG_ARCH_IOP3XX is not set +# CONFIG_ARCH_IXP4XX is not set +# CONFIG_ARCH_IXP2000 is not set +# CONFIG_ARCH_L7200 is not set +# CONFIG_ARCH_PXA is not set +# CONFIG_ARCH_RPC is not set +# CONFIG_ARCH_SA1100 is not set +# CONFIG_ARCH_S3C2410 is not set +# CONFIG_ARCH_SHARK is not set +# CONFIG_ARCH_LH7A40X is not set +# CONFIG_ARCH_OMAP is not set +# CONFIG_ARCH_VERSATILE is not set +# CONFIG_ARCH_REALVIEW is not set +# CONFIG_ARCH_IMX is not set +# CONFIG_ARCH_H720X is not set +# CONFIG_ARCH_AAEC2000 is not set +CONFIG_ARCH_AT91RM9200=y + +# +# AT91RM9200 Implementations +# + +# +# AT91RM9200 Board Type +# +# CONFIG_ARCH_AT91RM9200DK is not set +CONFIG_MACH_AT91RM9200EK=y +# CONFIG_MACH_CSB337 is not set +# CONFIG_MACH_CSB637 is not set +# CONFIG_MACH_CARMEVA is not set +# CONFIG_MACH_KB9200 is not set +# CONFIG_MACH_ATEB9200 is not set + +# +# AT91RM9200 Feature Selections +# +CONFIG_AT91_PROGRAMMABLE_CLOCKS=y + +# +# Processor Type +# +CONFIG_CPU_32=y +CONFIG_CPU_ARM920T=y +CONFIG_CPU_32v4=y +CONFIG_CPU_ABRT_EV4T=y +CONFIG_CPU_CACHE_V4WT=y +CONFIG_CPU_CACHE_VIVT=y +CONFIG_CPU_COPY_V4WB=y +CONFIG_CPU_TLB_V4WBI=y + +# +# Processor Features +# +# CONFIG_ARM_THUMB is not set +# CONFIG_CPU_ICACHE_DISABLE is not set +# CONFIG_CPU_DCACHE_DISABLE is not set +# CONFIG_CPU_DCACHE_WRITETHROUGH is not set + +# +# Bus support +# +CONFIG_ISA_DMA_API=y + +# +# PCCARD (PCMCIA/CardBus) support +# +# CONFIG_PCCARD is not set + +# +# Kernel Features +# +# CONFIG_PREEMPT is not set +# CONFIG_NO_IDLE_HZ is not set +# CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set +CONFIG_SELECT_MEMORY_MODEL=y +CONFIG_FLATMEM_MANUAL=y +# CONFIG_DISCONTIGMEM_MANUAL is not set +# CONFIG_SPARSEMEM_MANUAL is not set +CONFIG_FLATMEM=y +CONFIG_FLAT_NODE_MEM_MAP=y +# CONFIG_SPARSEMEM_STATIC is not set +CONFIG_SPLIT_PTLOCK_CPUS=4096 +CONFIG_LEDS=y +CONFIG_LEDS_TIMER=y +CONFIG_LEDS_CPU=y +CONFIG_ALIGNMENT_TRAP=y + +# +# Boot options +# +CONFIG_ZBOOT_ROM_TEXT=0x0 +CONFIG_ZBOOT_ROM_BSS=0x0 +CONFIG_CMDLINE="mem=32M console=ttyS0,115200 initrd=0x20410000,3145728 root=/dev/ram0 rw" +# CONFIG_XIP_KERNEL is not set + +# +# Floating point emulation +# + +# +# At least one emulation must be selected +# +CONFIG_FPE_NWFPE=y +# CONFIG_FPE_NWFPE_XP is not set +# CONFIG_FPE_FASTFPE is not set + +# +# Userspace binary formats +# +CONFIG_BINFMT_ELF=y +# CONFIG_BINFMT_AOUT is not set +# CONFIG_BINFMT_MISC is not set +# CONFIG_ARTHUR is not set + +# +# Power management options +# +# CONFIG_PM is not set + +# +# Networking +# +CONFIG_NET=y + +# +# Networking options +# +CONFIG_PACKET=y +# CONFIG_PACKET_MMAP is not set +CONFIG_UNIX=y +# CONFIG_NET_KEY is not set +CONFIG_INET=y +# CONFIG_IP_MULTICAST is not set +# CONFIG_IP_ADVANCED_ROUTER is not set +CONFIG_IP_FIB_HASH=y +CONFIG_IP_PNP=y +# CONFIG_IP_PNP_DHCP is not set +CONFIG_IP_PNP_BOOTP=y +# CONFIG_IP_PNP_RARP is not set +# CONFIG_NET_IPIP is not set +# CONFIG_NET_IPGRE is not set +# CONFIG_ARPD is not set +# CONFIG_SYN_COOKIES is not set +# CONFIG_INET_AH is not set +# CONFIG_INET_ESP is not set +# CONFIG_INET_IPCOMP is not set +# CONFIG_INET_TUNNEL is not set +CONFIG_INET_DIAG=y +CONFIG_INET_TCP_DIAG=y +# CONFIG_TCP_CONG_ADVANCED is not set +CONFIG_TCP_CONG_BIC=y +# CONFIG_IPV6 is not set +# CONFIG_NETFILTER is not set + +# +# DCCP Configuration (EXPERIMENTAL) +# +# CONFIG_IP_DCCP is not set + +# +# SCTP Configuration (EXPERIMENTAL) +# +# CONFIG_IP_SCTP is not set +# CONFIG_ATM is not set +# CONFIG_BRIDGE is not set +# CONFIG_VLAN_8021Q is not set +# CONFIG_DECNET is not set +# CONFIG_LLC2 is not set +# CONFIG_IPX is not set +# CONFIG_ATALK is not set +# CONFIG_X25 is not set +# CONFIG_LAPB is not set +# CONFIG_NET_DIVERT is not set +# CONFIG_ECONET is not set +# CONFIG_WAN_ROUTER is not set + +# +# QoS and/or fair queueing +# +# CONFIG_NET_SCHED is not set + +# +# Network testing +# +# CONFIG_NET_PKTGEN is not set +# CONFIG_HAMRADIO is not set +# CONFIG_IRDA is not set +# CONFIG_BT is not set +# CONFIG_IEEE80211 is not set + +# +# Device Drivers +# + +# +# Generic Driver Options +# +CONFIG_STANDALONE=y +CONFIG_PREVENT_FIRMWARE_BUILD=y +# CONFIG_FW_LOADER is not set +# CONFIG_DEBUG_DRIVER is not set + +# +# Connector - unified userspace <-> kernelspace linker +# +# CONFIG_CONNECTOR is not set + +# +# Memory Technology Devices (MTD) +# +CONFIG_MTD=y +# CONFIG_MTD_DEBUG is not set +# CONFIG_MTD_CONCAT is not set +CONFIG_MTD_PARTITIONS=y +# CONFIG_MTD_REDBOOT_PARTS is not set +CONFIG_MTD_CMDLINE_PARTS=y +# CONFIG_MTD_AFS_PARTS is not set + +# +# User Modules And Translation Layers +# +CONFIG_MTD_CHAR=y +CONFIG_MTD_BLOCK=y +# CONFIG_FTL is not set +# CONFIG_NFTL is not set +# CONFIG_INFTL is not set +# CONFIG_RFD_FTL is not set + +# +# RAM/ROM/Flash chip drivers +# +CONFIG_MTD_CFI=y +CONFIG_MTD_JEDECPROBE=y +CONFIG_MTD_GEN_PROBE=y +# CONFIG_MTD_CFI_ADV_OPTIONS is not set +CONFIG_MTD_MAP_BANK_WIDTH_1=y +CONFIG_MTD_MAP_BANK_WIDTH_2=y +CONFIG_MTD_MAP_BANK_WIDTH_4=y +# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set +CONFIG_MTD_CFI_I1=y +CONFIG_MTD_CFI_I2=y +# CONFIG_MTD_CFI_I4 is not set +# CONFIG_MTD_CFI_I8 is not set +# CONFIG_MTD_CFI_INTELEXT is not set +CONFIG_MTD_CFI_AMDSTD=y +CONFIG_MTD_CFI_AMDSTD_RETRY=0 +# CONFIG_MTD_CFI_STAA is not set +CONFIG_MTD_CFI_UTIL=y +# CONFIG_MTD_RAM is not set +# CONFIG_MTD_ROM is not set +# CONFIG_MTD_ABSENT is not set +# CONFIG_MTD_XIP is not set + +# +# Mapping drivers for chip access +# +# CONFIG_MTD_COMPLEX_MAPPINGS is not set +CONFIG_MTD_PHYSMAP=y +CONFIG_MTD_PHYSMAP_START=0x10000000 +CONFIG_MTD_PHYSMAP_LEN=0x800000 +CONFIG_MTD_PHYSMAP_BANKWIDTH=2 +# CONFIG_MTD_ARM_INTEGRATOR is not set +# CONFIG_MTD_IMPA7 is not set +# CONFIG_MTD_PLATRAM is not set + +# +# Self-contained MTD device drivers +# +# CONFIG_MTD_SLRAM is not set +# CONFIG_MTD_PHRAM is not set +# CONFIG_MTD_MTDRAM is not set +# CONFIG_MTD_BLKMTD is not set +# CONFIG_MTD_BLOCK2MTD is not set + +# +# Disk-On-Chip Device Drivers +# +# CONFIG_MTD_DOC2000 is not set +# CONFIG_MTD_DOC2001 is not set +# CONFIG_MTD_DOC2001PLUS is not set +CONFIG_MTD_AT91_DATAFLASH=y +CONFIG_MTD_AT91_DATAFLASH_CARD=y + +# +# NAND Flash Device Drivers +# +# CONFIG_MTD_NAND is not set + +# +# OneNAND Flash Device Drivers +# +# CONFIG_MTD_ONENAND is not set + +# +# Parallel port support +# +# CONFIG_PARPORT is not set + +# +# Plug and Play support +# + +# +# Block devices +# +# CONFIG_BLK_DEV_COW_COMMON is not set +# CONFIG_BLK_DEV_LOOP is not set +# CONFIG_BLK_DEV_NBD is not set +# CONFIG_BLK_DEV_UB is not set +CONFIG_BLK_DEV_RAM=y +CONFIG_BLK_DEV_RAM_COUNT=16 +CONFIG_BLK_DEV_RAM_SIZE=8192 +CONFIG_BLK_DEV_INITRD=y +# CONFIG_CDROM_PKTCDVD is not set +# CONFIG_ATA_OVER_ETH is not set + +# +# SCSI device support +# +# CONFIG_RAID_ATTRS is not set +# CONFIG_SCSI is not set + +# +# Multi-device support (RAID and LVM) +# +# CONFIG_MD is not set + +# +# Fusion MPT device support +# +# CONFIG_FUSION is not set + +# +# IEEE 1394 (FireWire) support +# + +# +# I2O device support +# + +# +# Network device support +# +CONFIG_NETDEVICES=y +# CONFIG_DUMMY is not set +# CONFIG_BONDING is not set +# CONFIG_EQUALIZER is not set +# CONFIG_TUN is not set + +# +# PHY device support +# +# CONFIG_PHYLIB is not set + +# +# Ethernet (10 or 100Mbit) +# +CONFIG_NET_ETHERNET=y +CONFIG_MII=y +CONFIG_ARM_AT91_ETHER=y +# CONFIG_SMC91X is not set +# CONFIG_DM9000 is not set + +# +# Ethernet (1000 Mbit) +# + +# +# Ethernet (10000 Mbit) +# + +# +# Token Ring devices +# + +# +# Wireless LAN (non-hamradio) +# +# CONFIG_NET_RADIO is not set + +# +# Wan interfaces +# +# CONFIG_WAN is not set +# CONFIG_PPP is not set +# CONFIG_SLIP is not set +# CONFIG_SHAPER is not set +# CONFIG_NETCONSOLE is not set +# CONFIG_NETPOLL is not set +# CONFIG_NET_POLL_CONTROLLER is not set + +# +# ISDN subsystem +# +# CONFIG_ISDN is not set + +# +# Input device support +# +CONFIG_INPUT=y + +# +# Userland interfaces +# +CONFIG_INPUT_MOUSEDEV=y +# CONFIG_INPUT_MOUSEDEV_PSAUX is not set +CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024 +CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 +# CONFIG_INPUT_JOYDEV is not set +# CONFIG_INPUT_TSDEV is not set +# CONFIG_INPUT_EVDEV is not set +# CONFIG_INPUT_EVBUG is not set + +# +# Input Device Drivers +# +# CONFIG_INPUT_KEYBOARD is not set +# CONFIG_INPUT_MOUSE is not set +# CONFIG_INPUT_JOYSTICK is not set +# CONFIG_INPUT_TOUCHSCREEN is not set +# CONFIG_INPUT_MISC is not set + +# +# Hardware I/O ports +# +# CONFIG_SERIO is not set +# CONFIG_GAMEPORT is not set + +# +# Character devices +# +CONFIG_VT=y +CONFIG_VT_CONSOLE=y +CONFIG_HW_CONSOLE=y +# CONFIG_SERIAL_NONSTANDARD is not set + +# +# Serial drivers +# +# CONFIG_SERIAL_8250 is not set + +# +# Non-8250 serial port support +# +CONFIG_SERIAL_AT91=y +CONFIG_SERIAL_AT91_CONSOLE=y +# CONFIG_SERIAL_AT91_TTYAT is not set +CONFIG_SERIAL_CORE=y +CONFIG_SERIAL_CORE_CONSOLE=y +CONFIG_UNIX98_PTYS=y +CONFIG_LEGACY_PTYS=y +CONFIG_LEGACY_PTY_COUNT=256 + +# +# IPMI +# +# CONFIG_IPMI_HANDLER is not set + +# +# Watchdog Cards +# +CONFIG_WATCHDOG=y +CONFIG_WATCHDOG_NOWAYOUT=y + +# +# Watchdog Device Drivers +# +# CONFIG_SOFT_WATCHDOG is not set +CONFIG_AT91_WATCHDOG=y + +# +# USB-based Watchdog Cards +# +# CONFIG_USBPCWATCHDOG is not set +# CONFIG_NVRAM is not set +# CONFIG_RTC is not set +CONFIG_AT91_RTC=y +# CONFIG_DTLK is not set +# CONFIG_R3964 is not set + +# +# Ftape, the floppy tape device driver +# +# CONFIG_RAW_DRIVER is not set + +# +# TPM devices +# +# CONFIG_TCG_TPM is not set +# CONFIG_TELCLOCK is not set +CONFIG_AT91_SPI=y +CONFIG_AT91_SPIDEV=y + +# +# I2C support +# +CONFIG_I2C=y +CONFIG_I2C_CHARDEV=y + +# +# I2C Algorithms +# +# CONFIG_I2C_ALGOBIT is not set +# CONFIG_I2C_ALGOPCF is not set +# CONFIG_I2C_ALGOPCA is not set + +# +# I2C Hardware Bus support +# +CONFIG_I2C_AT91=y +# CONFIG_I2C_PARPORT_LIGHT is not set +# CONFIG_I2C_STUB is not set +# CONFIG_I2C_PCA_ISA is not set + +# +# Miscellaneous I2C Chip support +# +# CONFIG_SENSORS_DS1337 is not set +# CONFIG_SENSORS_DS1374 is not set +# CONFIG_SENSORS_EEPROM is not set +# CONFIG_SENSORS_PCF8574 is not set +# CONFIG_SENSORS_PCA9539 is not set +# CONFIG_SENSORS_PCF8591 is not set +# CONFIG_SENSORS_RTC8564 is not set +# CONFIG_SENSORS_MAX6875 is not set +# CONFIG_RTC_X1205_I2C is not set +# CONFIG_I2C_DEBUG_CORE is not set +# CONFIG_I2C_DEBUG_ALGO is not set +# CONFIG_I2C_DEBUG_BUS is not set +# CONFIG_I2C_DEBUG_CHIP is not set + +# +# Hardware Monitoring support +# +CONFIG_HWMON=y +# CONFIG_HWMON_VID is not set +# CONFIG_SENSORS_ADM1021 is not set +# CONFIG_SENSORS_ADM1025 is not set +# CONFIG_SENSORS_ADM1026 is not set +# CONFIG_SENSORS_ADM1031 is not set +# CONFIG_SENSORS_ADM9240 is not set +# CONFIG_SENSORS_ASB100 is not set +# CONFIG_SENSORS_ATXP1 is not set +# CONFIG_SENSORS_DS1621 is not set +# CONFIG_SENSORS_FSCHER is not set +# CONFIG_SENSORS_FSCPOS is not set +# CONFIG_SENSORS_GL518SM is not set +# CONFIG_SENSORS_GL520SM is not set +# CONFIG_SENSORS_IT87 is not set +# CONFIG_SENSORS_LM63 is not set +# CONFIG_SENSORS_LM75 is not set +# CONFIG_SENSORS_LM77 is not set +# CONFIG_SENSORS_LM78 is not set +# CONFIG_SENSORS_LM80 is not set +# CONFIG_SENSORS_LM83 is not set +# CONFIG_SENSORS_LM85 is not set +# CONFIG_SENSORS_LM87 is not set +# CONFIG_SENSORS_LM90 is not set +# CONFIG_SENSORS_LM92 is not set +# CONFIG_SENSORS_MAX1619 is not set +# CONFIG_SENSORS_PC87360 is not set +# CONFIG_SENSORS_SMSC47M1 is not set +# CONFIG_SENSORS_SMSC47B397 is not set +# CONFIG_SENSORS_W83781D is not set +# CONFIG_SENSORS_W83792D is not set +# CONFIG_SENSORS_W83L785TS is not set +# CONFIG_SENSORS_W83627HF is not set +# CONFIG_SENSORS_W83627EHF is not set +# CONFIG_HWMON_DEBUG_CHIP is not set + +# +# Misc devices +# + +# +# Multimedia Capabilities Port drivers +# + +# +# Multimedia devices +# +# CONFIG_VIDEO_DEV is not set + +# +# Digital Video Broadcasting Devices +# +# CONFIG_DVB is not set + +# +# Graphics support +# +CONFIG_FB=y +CONFIG_FB_CFB_FILLRECT=y +CONFIG_FB_CFB_COPYAREA=y +CONFIG_FB_CFB_IMAGEBLIT=y +# CONFIG_FB_MACMODES is not set +# CONFIG_FB_MODE_HELPERS is not set +# CONFIG_FB_TILEBLITTING is not set +CONFIG_FB_S1D13XXX=y +# CONFIG_FB_VIRTUAL is not set + +# +# Console display driver support +# +# CONFIG_VGA_CONSOLE is not set +CONFIG_DUMMY_CONSOLE=y +# CONFIG_FRAMEBUFFER_CONSOLE is not set + +# +# Logo configuration +# +# CONFIG_LOGO is not set +# CONFIG_BACKLIGHT_LCD_SUPPORT is not set + +# +# Sound +# +# CONFIG_SOUND is not set + +# +# USB support +# +CONFIG_USB_ARCH_HAS_HCD=y +CONFIG_USB_ARCH_HAS_OHCI=y +CONFIG_USB=y +CONFIG_USB_DEBUG=y + +# +# Miscellaneous USB options +# +CONFIG_USB_DEVICEFS=y +# CONFIG_USB_BANDWIDTH is not set +# CONFIG_USB_DYNAMIC_MINORS is not set +# CONFIG_USB_OTG is not set + +# +# USB Host Controller Drivers +# +# CONFIG_USB_ISP116X_HCD is not set +CONFIG_USB_OHCI_HCD=y +# CONFIG_USB_OHCI_BIG_ENDIAN is not set +CONFIG_USB_OHCI_LITTLE_ENDIAN=y +# CONFIG_USB_SL811_HCD is not set + +# +# USB Device Class drivers +# +# CONFIG_USB_ACM is not set +# CONFIG_USB_PRINTER is not set + +# +# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' +# + +# +# may also be needed; see USB_STORAGE Help for more information +# +# CONFIG_USB_STORAGE is not set + +# +# USB Input Devices +# +# CONFIG_USB_HID is not set + +# +# USB HID Boot Protocol drivers +# +# CONFIG_USB_KBD is not set +# CONFIG_USB_MOUSE is not set +# CONFIG_USB_AIPTEK is not set +# CONFIG_USB_WACOM is not set +# CONFIG_USB_ACECAD is not set +# CONFIG_USB_KBTAB is not set +# CONFIG_USB_POWERMATE is not set +# CONFIG_USB_MTOUCH is not set +# CONFIG_USB_ITMTOUCH is not set +# CONFIG_USB_EGALAX is not set +# CONFIG_USB_YEALINK is not set +# CONFIG_USB_XPAD is not set +# CONFIG_USB_ATI_REMOTE is not set +# CONFIG_USB_KEYSPAN_REMOTE is not set +# CONFIG_USB_APPLETOUCH is not set + +# +# USB Imaging devices +# +# CONFIG_USB_MDC800 is not set + +# +# USB Multimedia devices +# +# CONFIG_USB_DABUSB is not set + +# +# Video4Linux support is needed for USB Multimedia device support +# + +# +# USB Network Adapters +# +# CONFIG_USB_CATC is not set +# CONFIG_USB_KAWETH is not set +# CONFIG_USB_PEGASUS is not set +# CONFIG_USB_RTL8150 is not set +# CONFIG_USB_USBNET is not set +CONFIG_USB_MON=y + +# +# USB port drivers +# + +# +# USB Serial Converter support +# +# CONFIG_USB_SERIAL is not set + +# +# USB Miscellaneous drivers +# +# CONFIG_USB_EMI62 is not set +# CONFIG_USB_EMI26 is not set +# CONFIG_USB_AUERSWALD is not set +# CONFIG_USB_RIO500 is not set +# CONFIG_USB_LEGOTOWER is not set +# CONFIG_USB_LCD is not set +# CONFIG_USB_LED is not set +# CONFIG_USB_CYTHERM is not set +# CONFIG_USB_PHIDGETKIT is not set +# CONFIG_USB_PHIDGETSERVO is not set +# CONFIG_USB_IDMOUSE is not set +# CONFIG_USB_LD is not set +# CONFIG_USB_TEST is not set + +# +# USB DSL modem support +# + +# +# USB Gadget Support +# +CONFIG_USB_GADGET=y +# CONFIG_USB_GADGET_DEBUG_FILES is not set +CONFIG_USB_GADGET_SELECTED=y +# CONFIG_USB_GADGET_NET2280 is not set +# CONFIG_USB_GADGET_PXA2XX is not set +# CONFIG_USB_GADGET_GOKU is not set +# CONFIG_USB_GADGET_LH7A40X is not set +# CONFIG_USB_GADGET_OMAP is not set +CONFIG_USB_GADGET_AT91=y +CONFIG_USB_AT91=y +# CONFIG_USB_GADGET_DUMMY_HCD is not set +# CONFIG_USB_GADGET_DUALSPEED is not set +# CONFIG_USB_ZERO is not set +# CONFIG_USB_ETH is not set +# CONFIG_USB_GADGETFS is not set +# CONFIG_USB_FILE_STORAGE is not set +# CONFIG_USB_G_SERIAL is not set + +# +# MMC/SD Card support +# +CONFIG_MMC=y +# CONFIG_MMC_DEBUG is not set +CONFIG_MMC_BLOCK=y +# CONFIG_MMC_WBSD is not set +CONFIG_MMC_AT91RM9200=y + +# +# File systems +# +CONFIG_EXT2_FS=y +# CONFIG_EXT2_FS_XATTR is not set +# CONFIG_EXT2_FS_XIP is not set +# CONFIG_EXT3_FS is not set +# CONFIG_JBD is not set +# CONFIG_REISERFS_FS is not set +# CONFIG_JFS_FS is not set +# CONFIG_FS_POSIX_ACL is not set +# CONFIG_XFS_FS is not set +# CONFIG_MINIX_FS is not set +# CONFIG_ROMFS_FS is not set +CONFIG_INOTIFY=y +# CONFIG_QUOTA is not set +CONFIG_DNOTIFY=y +# CONFIG_AUTOFS_FS is not set +# CONFIG_AUTOFS4_FS is not set +# CONFIG_FUSE_FS is not set + +# +# CD-ROM/DVD Filesystems +# +# CONFIG_ISO9660_FS is not set +# CONFIG_UDF_FS is not set + +# +# DOS/FAT/NT Filesystems +# +# CONFIG_MSDOS_FS is not set +# CONFIG_VFAT_FS is not set +# CONFIG_NTFS_FS is not set + +# +# Pseudo filesystems +# +CONFIG_PROC_FS=y +CONFIG_SYSFS=y +CONFIG_TMPFS=y +# CONFIG_HUGETLB_PAGE is not set +CONFIG_RAMFS=y +# CONFIG_RELAYFS_FS is not set + +# +# Miscellaneous filesystems +# +# CONFIG_ADFS_FS is not set +# CONFIG_AFFS_FS is not set +# CONFIG_HFS_FS is not set +# CONFIG_HFSPLUS_FS is not set +# CONFIG_BEFS_FS is not set +# CONFIG_BFS_FS is not set +# CONFIG_EFS_FS is not set +# CONFIG_JFFS_FS is not set +# CONFIG_JFFS2_FS is not set +CONFIG_CRAMFS=y +# CONFIG_VXFS_FS is not set +# CONFIG_HPFS_FS is not set +# CONFIG_QNX4FS_FS is not set +# CONFIG_SYSV_FS is not set +# CONFIG_UFS_FS is not set + +# +# Network File Systems +# +# CONFIG_NFS_FS is not set +# CONFIG_NFSD is not set +# CONFIG_SMB_FS is not set +# CONFIG_CIFS is not set +# CONFIG_NCP_FS is not set +# CONFIG_CODA_FS is not set +# CONFIG_AFS_FS is not set +# CONFIG_9P_FS is not set + +# +# Partition Types +# +# CONFIG_PARTITION_ADVANCED is not set +CONFIG_MSDOS_PARTITION=y + +# +# Native Language Support +# +# CONFIG_NLS is not set + +# +# Profiling support +# +# CONFIG_PROFILING is not set + +# +# Kernel hacking +# +# CONFIG_PRINTK_TIME is not set +CONFIG_DEBUG_KERNEL=y +# CONFIG_MAGIC_SYSRQ is not set +CONFIG_LOG_BUF_SHIFT=14 +CONFIG_DETECT_SOFTLOCKUP=y +# CONFIG_SCHEDSTATS is not set +# CONFIG_DEBUG_SLAB is not set +# CONFIG_DEBUG_SPINLOCK is not set +# CONFIG_DEBUG_SPINLOCK_SLEEP is not set +# CONFIG_DEBUG_KOBJECT is not set +CONFIG_DEBUG_BUGVERBOSE=y +# CONFIG_DEBUG_INFO is not set +# CONFIG_DEBUG_FS is not set +# CONFIG_DEBUG_VM is not set +CONFIG_FRAME_POINTER=y +# CONFIG_RCU_TORTURE_TEST is not set +CONFIG_DEBUG_USER=y +# CONFIG_DEBUG_WAITQ is not set +# CONFIG_DEBUG_ERRORS is not set +CONFIG_DEBUG_LL=y +# CONFIG_DEBUG_ICEDCC is not set + +# +# Security options +# +# CONFIG_KEYS is not set +# CONFIG_SECURITY is not set + +# +# Cryptographic options +# +# CONFIG_CRYPTO is not set + +# +# Hardware crypto devices +# + +# +# Library routines +# +# CONFIG_CRC_CCITT is not set +# CONFIG_CRC16 is not set +CONFIG_CRC32=y +# CONFIG_LIBCRC32C is not set +CONFIG_ZLIB_INFLATE=y diff --git a/arch/arm/configs/csb337_defconfig b/arch/arm/configs/csb337_defconfig new file mode 100644 index 000000000000..885a3184830a --- /dev/null +++ b/arch/arm/configs/csb337_defconfig @@ -0,0 +1,1136 @@ +# +# Automatically generated make config: don't edit +# Linux kernel version: 2.6.15 +# Mon Jan 9 21:51:31 2006 +# +CONFIG_ARM=y +CONFIG_MMU=y +CONFIG_UID16=y +CONFIG_RWSEM_GENERIC_SPINLOCK=y +CONFIG_GENERIC_CALIBRATE_DELAY=y + +# +# Code maturity level options +# +CONFIG_EXPERIMENTAL=y +CONFIG_CLEAN_COMPILE=y +CONFIG_BROKEN_ON_SMP=y +CONFIG_INIT_ENV_ARG_LIMIT=32 + +# +# General setup +# +CONFIG_LOCALVERSION="" +CONFIG_LOCALVERSION_AUTO=y +# CONFIG_SWAP is not set +CONFIG_SYSVIPC=y +# CONFIG_POSIX_MQUEUE is not set +# CONFIG_BSD_PROCESS_ACCT is not set +CONFIG_SYSCTL=y +# CONFIG_AUDIT is not set +CONFIG_HOTPLUG=y +CONFIG_KOBJECT_UEVENT=y +# CONFIG_IKCONFIG is not set +CONFIG_INITRAMFS_SOURCE="" +CONFIG_CC_OPTIMIZE_FOR_SIZE=y +# CONFIG_EMBEDDED is not set +CONFIG_KALLSYMS=y +# CONFIG_KALLSYMS_ALL is not set +# CONFIG_KALLSYMS_EXTRA_PASS is not set +CONFIG_PRINTK=y +CONFIG_BUG=y +CONFIG_BASE_FULL=y +CONFIG_FUTEX=y +CONFIG_EPOLL=y +CONFIG_SHMEM=y +CONFIG_CC_ALIGN_FUNCTIONS=0 +CONFIG_CC_ALIGN_LABELS=0 +CONFIG_CC_ALIGN_LOOPS=0 +CONFIG_CC_ALIGN_JUMPS=0 +# CONFIG_TINY_SHMEM is not set +CONFIG_BASE_SMALL=0 + +# +# Loadable module support +# +CONFIG_MODULES=y +CONFIG_MODULE_UNLOAD=y +# CONFIG_MODULE_FORCE_UNLOAD is not set +CONFIG_OBSOLETE_MODPARM=y +# CONFIG_MODVERSIONS is not set +# CONFIG_MODULE_SRCVERSION_ALL is not set +CONFIG_KMOD=y + +# +# Block layer +# + +# +# IO Schedulers +# +CONFIG_IOSCHED_NOOP=y +CONFIG_IOSCHED_AS=y +CONFIG_IOSCHED_DEADLINE=y +CONFIG_IOSCHED_CFQ=y +CONFIG_DEFAULT_AS=y +# CONFIG_DEFAULT_DEADLINE is not set +# CONFIG_DEFAULT_CFQ is not set +# CONFIG_DEFAULT_NOOP is not set +CONFIG_DEFAULT_IOSCHED="anticipatory" + +# +# System Type +# +# CONFIG_ARCH_CLPS7500 is not set +# CONFIG_ARCH_CLPS711X is not set +# CONFIG_ARCH_CO285 is not set +# CONFIG_ARCH_EBSA110 is not set +# CONFIG_ARCH_CAMELOT is not set +# CONFIG_ARCH_FOOTBRIDGE is not set +# CONFIG_ARCH_INTEGRATOR is not set +# CONFIG_ARCH_IOP3XX is not set +# CONFIG_ARCH_IXP4XX is not set +# CONFIG_ARCH_IXP2000 is not set +# CONFIG_ARCH_L7200 is not set +# CONFIG_ARCH_PXA is not set +# CONFIG_ARCH_RPC is not set +# CONFIG_ARCH_SA1100 is not set +# CONFIG_ARCH_S3C2410 is not set +# CONFIG_ARCH_SHARK is not set +# CONFIG_ARCH_LH7A40X is not set +# CONFIG_ARCH_OMAP is not set +# CONFIG_ARCH_VERSATILE is not set +# CONFIG_ARCH_REALVIEW is not set +# CONFIG_ARCH_IMX is not set +# CONFIG_ARCH_H720X is not set +# CONFIG_ARCH_AAEC2000 is not set +CONFIG_ARCH_AT91RM9200=y + +# +# AT91RM9200 Implementations +# + +# +# AT91RM9200 Board Type +# +# CONFIG_ARCH_AT91RM9200DK is not set +# CONFIG_MACH_AT91RM9200EK is not set +CONFIG_MACH_CSB337=y +# CONFIG_MACH_CSB637 is not set +# CONFIG_MACH_CARMEVA is not set +# CONFIG_MACH_KB9200 is not set +# CONFIG_MACH_ATEB9200 is not set + +# +# AT91RM9200 Feature Selections +# +CONFIG_AT91_PROGRAMMABLE_CLOCKS=y + +# +# Processor Type +# +CONFIG_CPU_32=y +CONFIG_CPU_ARM920T=y +CONFIG_CPU_32v4=y +CONFIG_CPU_ABRT_EV4T=y +CONFIG_CPU_CACHE_V4WT=y +CONFIG_CPU_CACHE_VIVT=y +CONFIG_CPU_COPY_V4WB=y +CONFIG_CPU_TLB_V4WBI=y + +# +# Processor Features +# +# CONFIG_ARM_THUMB is not set +# CONFIG_CPU_ICACHE_DISABLE is not set +# CONFIG_CPU_DCACHE_DISABLE is not set +# CONFIG_CPU_DCACHE_WRITETHROUGH is not set + +# +# Bus support +# +CONFIG_ISA_DMA_API=y + +# +# PCCARD (PCMCIA/CardBus) support +# +CONFIG_PCCARD=y +# CONFIG_PCMCIA_DEBUG is not set +CONFIG_PCMCIA=y +CONFIG_PCMCIA_LOAD_CIS=y +CONFIG_PCMCIA_IOCTL=y + +# +# PC-card bridges +# +CONFIG_AT91_CF=y + +# +# Kernel Features +# +# CONFIG_PREEMPT is not set +# CONFIG_NO_IDLE_HZ is not set +# CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set +CONFIG_SELECT_MEMORY_MODEL=y +CONFIG_FLATMEM_MANUAL=y +# CONFIG_DISCONTIGMEM_MANUAL is not set +# CONFIG_SPARSEMEM_MANUAL is not set +CONFIG_FLATMEM=y +CONFIG_FLAT_NODE_MEM_MAP=y +# CONFIG_SPARSEMEM_STATIC is not set +CONFIG_SPLIT_PTLOCK_CPUS=4096 +CONFIG_LEDS=y +CONFIG_LEDS_TIMER=y +CONFIG_LEDS_CPU=y +CONFIG_ALIGNMENT_TRAP=y + +# +# Boot options +# +CONFIG_ZBOOT_ROM_TEXT=0x0 +CONFIG_ZBOOT_ROM_BSS=0x0 +CONFIG_CMDLINE="mem=32M console=ttyS0,38400 initrd=0x20410000,3145728 root=/dev/ram0 rw" +# CONFIG_XIP_KERNEL is not set + +# +# Floating point emulation +# + +# +# At least one emulation must be selected +# +CONFIG_FPE_NWFPE=y +# CONFIG_FPE_NWFPE_XP is not set +# CONFIG_FPE_FASTFPE is not set + +# +# Userspace binary formats +# +CONFIG_BINFMT_ELF=y +# CONFIG_BINFMT_AOUT is not set +# CONFIG_BINFMT_MISC is not set +# CONFIG_ARTHUR is not set + +# +# Power management options +# +# CONFIG_PM is not set + +# +# Networking +# +CONFIG_NET=y + +# +# Networking options +# +CONFIG_PACKET=y +# CONFIG_PACKET_MMAP is not set +CONFIG_UNIX=y +# CONFIG_NET_KEY is not set +CONFIG_INET=y +# CONFIG_IP_MULTICAST is not set +# CONFIG_IP_ADVANCED_ROUTER is not set +CONFIG_IP_FIB_HASH=y +CONFIG_IP_PNP=y +CONFIG_IP_PNP_DHCP=y +CONFIG_IP_PNP_BOOTP=y +# CONFIG_IP_PNP_RARP is not set +# CONFIG_NET_IPIP is not set +# CONFIG_NET_IPGRE is not set +# CONFIG_ARPD is not set +# CONFIG_SYN_COOKIES is not set +# CONFIG_INET_AH is not set +# CONFIG_INET_ESP is not set +# CONFIG_INET_IPCOMP is not set +# CONFIG_INET_TUNNEL is not set +CONFIG_INET_DIAG=y +CONFIG_INET_TCP_DIAG=y +# CONFIG_TCP_CONG_ADVANCED is not set +CONFIG_TCP_CONG_BIC=y +# CONFIG_IPV6 is not set +# CONFIG_NETFILTER is not set + +# +# DCCP Configuration (EXPERIMENTAL) +# +# CONFIG_IP_DCCP is not set + +# +# SCTP Configuration (EXPERIMENTAL) +# +# CONFIG_IP_SCTP is not set +# CONFIG_ATM is not set +# CONFIG_BRIDGE is not set +# CONFIG_VLAN_8021Q is not set +# CONFIG_DECNET is not set +# CONFIG_LLC2 is not set +# CONFIG_IPX is not set +# CONFIG_ATALK is not set +# CONFIG_X25 is not set +# CONFIG_LAPB is not set +# CONFIG_NET_DIVERT is not set +# CONFIG_ECONET is not set +# CONFIG_WAN_ROUTER is not set + +# +# QoS and/or fair queueing +# +# CONFIG_NET_SCHED is not set + +# +# Network testing +# +# CONFIG_NET_PKTGEN is not set +# CONFIG_HAMRADIO is not set +# CONFIG_IRDA is not set +# CONFIG_BT is not set +# CONFIG_IEEE80211 is not set + +# +# Device Drivers +# + +# +# Generic Driver Options +# +CONFIG_STANDALONE=y +CONFIG_PREVENT_FIRMWARE_BUILD=y +CONFIG_FW_LOADER=y +# CONFIG_DEBUG_DRIVER is not set + +# +# Connector - unified userspace <-> kernelspace linker +# +# CONFIG_CONNECTOR is not set + +# +# Memory Technology Devices (MTD) +# +CONFIG_MTD=y +# CONFIG_MTD_DEBUG is not set +# CONFIG_MTD_CONCAT is not set +CONFIG_MTD_PARTITIONS=y +# CONFIG_MTD_REDBOOT_PARTS is not set +CONFIG_MTD_CMDLINE_PARTS=y +# CONFIG_MTD_AFS_PARTS is not set + +# +# User Modules And Translation Layers +# +CONFIG_MTD_CHAR=y +CONFIG_MTD_BLOCK=y +# CONFIG_FTL is not set +# CONFIG_NFTL is not set +# CONFIG_INFTL is not set +# CONFIG_RFD_FTL is not set + +# +# RAM/ROM/Flash chip drivers +# +CONFIG_MTD_CFI=y +# CONFIG_MTD_JEDECPROBE is not set +CONFIG_MTD_GEN_PROBE=y +# CONFIG_MTD_CFI_ADV_OPTIONS is not set +CONFIG_MTD_MAP_BANK_WIDTH_1=y +CONFIG_MTD_MAP_BANK_WIDTH_2=y +CONFIG_MTD_MAP_BANK_WIDTH_4=y +# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set +CONFIG_MTD_CFI_I1=y +CONFIG_MTD_CFI_I2=y +# CONFIG_MTD_CFI_I4 is not set +# CONFIG_MTD_CFI_I8 is not set +CONFIG_MTD_CFI_INTELEXT=y +# CONFIG_MTD_CFI_AMDSTD is not set +# CONFIG_MTD_CFI_STAA is not set +CONFIG_MTD_CFI_UTIL=y +# CONFIG_MTD_RAM is not set +# CONFIG_MTD_ROM is not set +# CONFIG_MTD_ABSENT is not set +# CONFIG_MTD_XIP is not set + +# +# Mapping drivers for chip access +# +# CONFIG_MTD_COMPLEX_MAPPINGS is not set +# CONFIG_MTD_PHYSMAP is not set +# CONFIG_MTD_ARM_INTEGRATOR is not set +# CONFIG_MTD_PLATRAM is not set +CONFIG_MTD_CSB337=y + +# +# Self-contained MTD device drivers +# +# CONFIG_MTD_SLRAM is not set +# CONFIG_MTD_PHRAM is not set +# CONFIG_MTD_MTDRAM is not set +# CONFIG_MTD_BLKMTD is not set +# CONFIG_MTD_BLOCK2MTD is not set + +# +# Disk-On-Chip Device Drivers +# +# CONFIG_MTD_DOC2000 is not set +# CONFIG_MTD_DOC2001 is not set +# CONFIG_MTD_DOC2001PLUS is not set +# CONFIG_MTD_AT91_DATAFLASH is not set + +# +# NAND Flash Device Drivers +# +# CONFIG_MTD_NAND is not set + +# +# OneNAND Flash Device Drivers +# +# CONFIG_MTD_ONENAND is not set + +# +# Parallel port support +# +# CONFIG_PARPORT is not set + +# +# Plug and Play support +# + +# +# Block devices +# +# CONFIG_BLK_DEV_COW_COMMON is not set +CONFIG_BLK_DEV_LOOP=y +# CONFIG_BLK_DEV_CRYPTOLOOP is not set +# CONFIG_BLK_DEV_NBD is not set +# CONFIG_BLK_DEV_UB is not set +CONFIG_BLK_DEV_RAM=y +CONFIG_BLK_DEV_RAM_COUNT=16 +CONFIG_BLK_DEV_RAM_SIZE=8192 +CONFIG_BLK_DEV_INITRD=y +# CONFIG_CDROM_PKTCDVD is not set +# CONFIG_ATA_OVER_ETH is not set + +# +# ATA/ATAPI/MFM/RLL support +# +# CONFIG_IDE is not set + +# +# SCSI device support +# +# CONFIG_RAID_ATTRS is not set +CONFIG_SCSI=y +CONFIG_SCSI_PROC_FS=y + +# +# SCSI support type (disk, tape, CD-ROM) +# +# CONFIG_BLK_DEV_SD is not set +# CONFIG_CHR_DEV_ST is not set +# CONFIG_CHR_DEV_OSST is not set +# CONFIG_BLK_DEV_SR is not set +# CONFIG_CHR_DEV_SG is not set +# CONFIG_CHR_DEV_SCH is not set + +# +# Some SCSI devices (e.g. CD jukebox) support multiple LUNs +# +# CONFIG_SCSI_MULTI_LUN is not set +# CONFIG_SCSI_CONSTANTS is not set +# CONFIG_SCSI_LOGGING is not set + +# +# SCSI Transport Attributes +# +# CONFIG_SCSI_SPI_ATTRS is not set +# CONFIG_SCSI_FC_ATTRS is not set +# CONFIG_SCSI_ISCSI_ATTRS is not set +# CONFIG_SCSI_SAS_ATTRS is not set + +# +# SCSI low-level drivers +# +# CONFIG_ISCSI_TCP is not set +# CONFIG_SCSI_SATA is not set +# CONFIG_SCSI_DEBUG is not set + +# +# PCMCIA SCSI adapter support +# +# CONFIG_PCMCIA_AHA152X is not set +# CONFIG_PCMCIA_FDOMAIN is not set +# CONFIG_PCMCIA_NINJA_SCSI is not set +# CONFIG_PCMCIA_QLOGIC is not set +# CONFIG_PCMCIA_SYM53C500 is not set + +# +# Multi-device support (RAID and LVM) +# +# CONFIG_MD is not set + +# +# Fusion MPT device support +# +# CONFIG_FUSION is not set + +# +# IEEE 1394 (FireWire) support +# + +# +# I2O device support +# + +# +# Network device support +# +CONFIG_NETDEVICES=y +# CONFIG_DUMMY is not set +# CONFIG_BONDING is not set +# CONFIG_EQUALIZER is not set +# CONFIG_TUN is not set + +# +# PHY device support +# +# CONFIG_PHYLIB is not set + +# +# Ethernet (10 or 100Mbit) +# +CONFIG_NET_ETHERNET=y +CONFIG_MII=y +CONFIG_ARM_AT91_ETHER=y +# CONFIG_SMC91X is not set +# CONFIG_DM9000 is not set + +# +# Ethernet (1000 Mbit) +# + +# +# Ethernet (10000 Mbit) +# + +# +# Token Ring devices +# + +# +# Wireless LAN (non-hamradio) +# +# CONFIG_NET_RADIO is not set + +# +# PCMCIA network device support +# +# CONFIG_NET_PCMCIA is not set + +# +# Wan interfaces +# +# CONFIG_WAN is not set +# CONFIG_PPP is not set +# CONFIG_SLIP is not set +# CONFIG_SHAPER is not set +# CONFIG_NETCONSOLE is not set +# CONFIG_NETPOLL is not set +# CONFIG_NET_POLL_CONTROLLER is not set + +# +# ISDN subsystem +# +# CONFIG_ISDN is not set + +# +# Input device support +# +CONFIG_INPUT=y + +# +# Userland interfaces +# +CONFIG_INPUT_MOUSEDEV=y +CONFIG_INPUT_MOUSEDEV_PSAUX=y +CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024 +CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 +# CONFIG_INPUT_JOYDEV is not set +# CONFIG_INPUT_TSDEV is not set +# CONFIG_INPUT_EVDEV is not set +# CONFIG_INPUT_EVBUG is not set + +# +# Input Device Drivers +# +# CONFIG_INPUT_KEYBOARD is not set +# CONFIG_INPUT_MOUSE is not set +# CONFIG_INPUT_JOYSTICK is not set +# CONFIG_INPUT_TOUCHSCREEN is not set +# CONFIG_INPUT_MISC is not set + +# +# Hardware I/O ports +# +# CONFIG_SERIO is not set +# CONFIG_GAMEPORT is not set + +# +# Character devices +# +CONFIG_VT=y +CONFIG_VT_CONSOLE=y +CONFIG_HW_CONSOLE=y +# CONFIG_SERIAL_NONSTANDARD is not set + +# +# Serial drivers +# +# CONFIG_SERIAL_8250 is not set + +# +# Non-8250 serial port support +# +CONFIG_SERIAL_AT91=y +CONFIG_SERIAL_AT91_CONSOLE=y +# CONFIG_SERIAL_AT91_TTYAT is not set +CONFIG_SERIAL_CORE=y +CONFIG_SERIAL_CORE_CONSOLE=y +CONFIG_UNIX98_PTYS=y +CONFIG_LEGACY_PTYS=y +CONFIG_LEGACY_PTY_COUNT=256 + +# +# IPMI +# +# CONFIG_IPMI_HANDLER is not set + +# +# Watchdog Cards +# +CONFIG_WATCHDOG=y +CONFIG_WATCHDOG_NOWAYOUT=y + +# +# Watchdog Device Drivers +# +# CONFIG_SOFT_WATCHDOG is not set +CONFIG_AT91_WATCHDOG=y + +# +# USB-based Watchdog Cards +# +# CONFIG_USBPCWATCHDOG is not set +# CONFIG_NVRAM is not set +CONFIG_RTC=y +# CONFIG_AT91_RTC is not set +# CONFIG_DTLK is not set +# CONFIG_R3964 is not set + +# +# Ftape, the floppy tape device driver +# + +# +# PCMCIA character devices +# +# CONFIG_SYNCLINK_CS is not set +# CONFIG_CARDMAN_4000 is not set +# CONFIG_CARDMAN_4040 is not set +# CONFIG_RAW_DRIVER is not set + +# +# TPM devices +# +# CONFIG_TCG_TPM is not set +# CONFIG_TELCLOCK is not set +CONFIG_AT91_SPI=y +CONFIG_AT91_SPIDEV=y + +# +# I2C support +# +CONFIG_I2C=y +CONFIG_I2C_CHARDEV=y + +# +# I2C Algorithms +# +# CONFIG_I2C_ALGOBIT is not set +# CONFIG_I2C_ALGOPCF is not set +# CONFIG_I2C_ALGOPCA is not set + +# +# I2C Hardware Bus support +# +CONFIG_I2C_AT91=y +# CONFIG_I2C_PARPORT_LIGHT is not set +# CONFIG_I2C_STUB is not set +# CONFIG_I2C_PCA_ISA is not set + +# +# Miscellaneous I2C Chip support +# +# CONFIG_SENSORS_DS1337 is not set +# CONFIG_SENSORS_DS1374 is not set +# CONFIG_SENSORS_EEPROM is not set +# CONFIG_SENSORS_PCF8574 is not set +# CONFIG_SENSORS_PCA9539 is not set +# CONFIG_SENSORS_PCF8591 is not set +# CONFIG_SENSORS_RTC8564 is not set +# CONFIG_SENSORS_MAX6875 is not set +# CONFIG_RTC_X1205_I2C is not set +# CONFIG_I2C_DEBUG_CORE is not set +# CONFIG_I2C_DEBUG_ALGO is not set +# CONFIG_I2C_DEBUG_BUS is not set +# CONFIG_I2C_DEBUG_CHIP is not set + +# +# Hardware Monitoring support +# +CONFIG_HWMON=y +# CONFIG_HWMON_VID is not set +# CONFIG_SENSORS_ADM1021 is not set +# CONFIG_SENSORS_ADM1025 is not set +# CONFIG_SENSORS_ADM1026 is not set +# CONFIG_SENSORS_ADM1031 is not set +# CONFIG_SENSORS_ADM9240 is not set +# CONFIG_SENSORS_ASB100 is not set +# CONFIG_SENSORS_ATXP1 is not set +# CONFIG_SENSORS_DS1621 is not set +# CONFIG_SENSORS_FSCHER is not set +# CONFIG_SENSORS_FSCPOS is not set +# CONFIG_SENSORS_GL518SM is not set +# CONFIG_SENSORS_GL520SM is not set +# CONFIG_SENSORS_IT87 is not set +# CONFIG_SENSORS_LM63 is not set +# CONFIG_SENSORS_LM75 is not set +# CONFIG_SENSORS_LM77 is not set +# CONFIG_SENSORS_LM78 is not set +# CONFIG_SENSORS_LM80 is not set +# CONFIG_SENSORS_LM83 is not set +# CONFIG_SENSORS_LM85 is not set +# CONFIG_SENSORS_LM87 is not set +# CONFIG_SENSORS_LM90 is not set +# CONFIG_SENSORS_LM92 is not set +# CONFIG_SENSORS_MAX1619 is not set +# CONFIG_SENSORS_PC87360 is not set +# CONFIG_SENSORS_SMSC47M1 is not set +# CONFIG_SENSORS_SMSC47B397 is not set +# CONFIG_SENSORS_W83781D is not set +# CONFIG_SENSORS_W83792D is not set +# CONFIG_SENSORS_W83L785TS is not set +# CONFIG_SENSORS_W83627HF is not set +# CONFIG_SENSORS_W83627EHF is not set +# CONFIG_HWMON_DEBUG_CHIP is not set + +# +# Misc devices +# + +# +# Multimedia Capabilities Port drivers +# + +# +# Multimedia devices +# +# CONFIG_VIDEO_DEV is not set + +# +# Digital Video Broadcasting Devices +# +# CONFIG_DVB is not set + +# +# Graphics support +# +# CONFIG_FB is not set + +# +# Console display driver support +# +# CONFIG_VGA_CONSOLE is not set +CONFIG_DUMMY_CONSOLE=y + +# +# Sound +# +# CONFIG_SOUND is not set + +# +# USB support +# +CONFIG_USB_ARCH_HAS_HCD=y +CONFIG_USB_ARCH_HAS_OHCI=y +CONFIG_USB=y +CONFIG_USB_DEBUG=y + +# +# Miscellaneous USB options +# +CONFIG_USB_DEVICEFS=y +# CONFIG_USB_BANDWIDTH is not set +# CONFIG_USB_DYNAMIC_MINORS is not set +# CONFIG_USB_OTG is not set + +# +# USB Host Controller Drivers +# +# CONFIG_USB_ISP116X_HCD is not set +CONFIG_USB_OHCI_HCD=y +# CONFIG_USB_OHCI_BIG_ENDIAN is not set +CONFIG_USB_OHCI_LITTLE_ENDIAN=y +# CONFIG_USB_SL811_HCD is not set + +# +# USB Device Class drivers +# +# CONFIG_USB_ACM is not set +# CONFIG_USB_PRINTER is not set + +# +# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' +# + +# +# may also be needed; see USB_STORAGE Help for more information +# +CONFIG_USB_STORAGE=y +# CONFIG_USB_STORAGE_DEBUG is not set +# CONFIG_USB_STORAGE_DATAFAB is not set +# CONFIG_USB_STORAGE_FREECOM is not set +# CONFIG_USB_STORAGE_DPCM is not set +# CONFIG_USB_STORAGE_USBAT is not set +# CONFIG_USB_STORAGE_SDDR09 is not set +# CONFIG_USB_STORAGE_SDDR55 is not set +# CONFIG_USB_STORAGE_JUMPSHOT is not set + +# +# USB Input Devices +# +# CONFIG_USB_HID is not set + +# +# USB HID Boot Protocol drivers +# +# CONFIG_USB_KBD is not set +# CONFIG_USB_MOUSE is not set +# CONFIG_USB_AIPTEK is not set +# CONFIG_USB_WACOM is not set +# CONFIG_USB_ACECAD is not set +# CONFIG_USB_KBTAB is not set +# CONFIG_USB_POWERMATE is not set +# CONFIG_USB_MTOUCH is not set +# CONFIG_USB_ITMTOUCH is not set +# CONFIG_USB_EGALAX is not set +# CONFIG_USB_YEALINK is not set +# CONFIG_USB_XPAD is not set +# CONFIG_USB_ATI_REMOTE is not set +# CONFIG_USB_KEYSPAN_REMOTE is not set +# CONFIG_USB_APPLETOUCH is not set + +# +# USB Imaging devices +# +# CONFIG_USB_MDC800 is not set +# CONFIG_USB_MICROTEK is not set + +# +# USB Multimedia devices +# +# CONFIG_USB_DABUSB is not set + +# +# Video4Linux support is needed for USB Multimedia device support +# + +# +# USB Network Adapters +# +# CONFIG_USB_CATC is not set +# CONFIG_USB_KAWETH is not set +# CONFIG_USB_PEGASUS is not set +# CONFIG_USB_RTL8150 is not set +# CONFIG_USB_USBNET is not set +CONFIG_USB_MON=y + +# +# USB port drivers +# + +# +# USB Serial Converter support +# +CONFIG_USB_SERIAL=y +CONFIG_USB_SERIAL_CONSOLE=y +CONFIG_USB_SERIAL_GENERIC=y +# CONFIG_USB_SERIAL_AIRPRIME is not set +# CONFIG_USB_SERIAL_ANYDATA is not set +# CONFIG_USB_SERIAL_BELKIN is not set +# CONFIG_USB_SERIAL_WHITEHEAT is not set +# CONFIG_USB_SERIAL_DIGI_ACCELEPORT is not set +# CONFIG_USB_SERIAL_CP2101 is not set +# CONFIG_USB_SERIAL_CYPRESS_M8 is not set +# CONFIG_USB_SERIAL_EMPEG is not set +CONFIG_USB_SERIAL_FTDI_SIO=y +# CONFIG_USB_SERIAL_VISOR is not set +# CONFIG_USB_SERIAL_IPAQ is not set +# CONFIG_USB_SERIAL_IR is not set +# CONFIG_USB_SERIAL_EDGEPORT is not set +# CONFIG_USB_SERIAL_EDGEPORT_TI is not set +# CONFIG_USB_SERIAL_GARMIN is not set +# CONFIG_USB_SERIAL_IPW is not set +# CONFIG_USB_SERIAL_KEYSPAN_PDA is not set +CONFIG_USB_SERIAL_KEYSPAN=y +CONFIG_USB_SERIAL_KEYSPAN_MPR=y +CONFIG_USB_SERIAL_KEYSPAN_USA28=y +CONFIG_USB_SERIAL_KEYSPAN_USA28X=y +CONFIG_USB_SERIAL_KEYSPAN_USA28XA=y +CONFIG_USB_SERIAL_KEYSPAN_USA28XB=y +CONFIG_USB_SERIAL_KEYSPAN_USA19=y +CONFIG_USB_SERIAL_KEYSPAN_USA18X=y +CONFIG_USB_SERIAL_KEYSPAN_USA19W=y +CONFIG_USB_SERIAL_KEYSPAN_USA19QW=y +CONFIG_USB_SERIAL_KEYSPAN_USA19QI=y +CONFIG_USB_SERIAL_KEYSPAN_USA49W=y +CONFIG_USB_SERIAL_KEYSPAN_USA49WLC=y +# CONFIG_USB_SERIAL_KLSI is not set +# CONFIG_USB_SERIAL_KOBIL_SCT is not set +CONFIG_USB_SERIAL_MCT_U232=y +# CONFIG_USB_SERIAL_PL2303 is not set +# CONFIG_USB_SERIAL_HP4X is not set +# CONFIG_USB_SERIAL_SAFE is not set +# CONFIG_USB_SERIAL_TI is not set +# CONFIG_USB_SERIAL_CYBERJACK is not set +# CONFIG_USB_SERIAL_XIRCOM is not set +# CONFIG_USB_SERIAL_OPTION is not set +# CONFIG_USB_SERIAL_OMNINET is not set +CONFIG_USB_EZUSB=y + +# +# USB Miscellaneous drivers +# +# CONFIG_USB_EMI62 is not set +# CONFIG_USB_EMI26 is not set +# CONFIG_USB_AUERSWALD is not set +# CONFIG_USB_RIO500 is not set +# CONFIG_USB_LEGOTOWER is not set +# CONFIG_USB_LCD is not set +# CONFIG_USB_LED is not set +# CONFIG_USB_CYTHERM is not set +# CONFIG_USB_PHIDGETKIT is not set +# CONFIG_USB_PHIDGETSERVO is not set +# CONFIG_USB_IDMOUSE is not set +# CONFIG_USB_LD is not set +# CONFIG_USB_TEST is not set + +# +# USB DSL modem support +# + +# +# USB Gadget Support +# +CONFIG_USB_GADGET=y +# CONFIG_USB_GADGET_DEBUG_FILES is not set +CONFIG_USB_GADGET_SELECTED=y +# CONFIG_USB_GADGET_NET2280 is not set +# CONFIG_USB_GADGET_PXA2XX is not set +# CONFIG_USB_GADGET_GOKU is not set +# CONFIG_USB_GADGET_LH7A40X is not set +# CONFIG_USB_GADGET_OMAP is not set +CONFIG_USB_GADGET_AT91=y +CONFIG_USB_AT91=y +# CONFIG_USB_GADGET_DUMMY_HCD is not set +# CONFIG_USB_GADGET_DUALSPEED is not set +# CONFIG_USB_ZERO is not set +# CONFIG_USB_ETH is not set +# CONFIG_USB_GADGETFS is not set +# CONFIG_USB_FILE_STORAGE is not set +# CONFIG_USB_G_SERIAL is not set + +# +# MMC/SD Card support +# +CONFIG_MMC=y +# CONFIG_MMC_DEBUG is not set +CONFIG_MMC_BLOCK=y +# CONFIG_MMC_WBSD is not set +CONFIG_MMC_AT91RM9200=y + +# +# File systems +# +CONFIG_EXT2_FS=y +# CONFIG_EXT2_FS_XATTR is not set +# CONFIG_EXT2_FS_XIP is not set +# CONFIG_EXT3_FS is not set +# CONFIG_JBD is not set +# CONFIG_REISERFS_FS is not set +# CONFIG_JFS_FS is not set +# CONFIG_FS_POSIX_ACL is not set +# CONFIG_XFS_FS is not set +# CONFIG_MINIX_FS is not set +# CONFIG_ROMFS_FS is not set +CONFIG_INOTIFY=y +# CONFIG_QUOTA is not set +CONFIG_DNOTIFY=y +# CONFIG_AUTOFS_FS is not set +# CONFIG_AUTOFS4_FS is not set +# CONFIG_FUSE_FS is not set + +# +# CD-ROM/DVD Filesystems +# +# CONFIG_ISO9660_FS is not set +# CONFIG_UDF_FS is not set + +# +# DOS/FAT/NT Filesystems +# +# CONFIG_MSDOS_FS is not set +# CONFIG_VFAT_FS is not set +# CONFIG_NTFS_FS is not set + +# +# Pseudo filesystems +# +CONFIG_PROC_FS=y +CONFIG_SYSFS=y +CONFIG_TMPFS=y +# CONFIG_HUGETLB_PAGE is not set +CONFIG_RAMFS=y +# CONFIG_RELAYFS_FS is not set + +# +# Miscellaneous filesystems +# +# CONFIG_ADFS_FS is not set +# CONFIG_AFFS_FS is not set +# CONFIG_HFS_FS is not set +# CONFIG_HFSPLUS_FS is not set +# CONFIG_BEFS_FS is not set +# CONFIG_BFS_FS is not set +# CONFIG_EFS_FS is not set +# CONFIG_JFFS_FS is not set +# CONFIG_JFFS2_FS is not set +CONFIG_CRAMFS=y +# CONFIG_VXFS_FS is not set +# CONFIG_HPFS_FS is not set +# CONFIG_QNX4FS_FS is not set +# CONFIG_SYSV_FS is not set +# CONFIG_UFS_FS is not set + +# +# Network File Systems +# +CONFIG_NFS_FS=y +CONFIG_NFS_V3=y +# CONFIG_NFS_V3_ACL is not set +CONFIG_NFS_V4=y +# CONFIG_NFS_DIRECTIO is not set +# CONFIG_NFSD is not set +CONFIG_ROOT_NFS=y +CONFIG_LOCKD=y +CONFIG_LOCKD_V4=y +CONFIG_NFS_COMMON=y +CONFIG_SUNRPC=y +CONFIG_SUNRPC_GSS=y +CONFIG_RPCSEC_GSS_KRB5=y +# CONFIG_RPCSEC_GSS_SPKM3 is not set +# CONFIG_SMB_FS is not set +# CONFIG_CIFS is not set +# CONFIG_NCP_FS is not set +# CONFIG_CODA_FS is not set +# CONFIG_AFS_FS is not set +# CONFIG_9P_FS is not set + +# +# Partition Types +# +# CONFIG_PARTITION_ADVANCED is not set +CONFIG_MSDOS_PARTITION=y + +# +# Native Language Support +# +# CONFIG_NLS is not set + +# +# Profiling support +# +# CONFIG_PROFILING is not set + +# +# Kernel hacking +# +# CONFIG_PRINTK_TIME is not set +CONFIG_DEBUG_KERNEL=y +# CONFIG_MAGIC_SYSRQ is not set +CONFIG_LOG_BUF_SHIFT=14 +CONFIG_DETECT_SOFTLOCKUP=y +# CONFIG_SCHEDSTATS is not set +# CONFIG_DEBUG_SLAB is not set +# CONFIG_DEBUG_SPINLOCK is not set +# CONFIG_DEBUG_SPINLOCK_SLEEP is not set +# CONFIG_DEBUG_KOBJECT is not set +CONFIG_DEBUG_BUGVERBOSE=y +# CONFIG_DEBUG_INFO is not set +# CONFIG_DEBUG_FS is not set +# CONFIG_DEBUG_VM is not set +CONFIG_FRAME_POINTER=y +# CONFIG_RCU_TORTURE_TEST is not set +CONFIG_DEBUG_USER=y +# CONFIG_DEBUG_WAITQ is not set +# CONFIG_DEBUG_ERRORS is not set +CONFIG_DEBUG_LL=y +# CONFIG_DEBUG_ICEDCC is not set + +# +# Security options +# +# CONFIG_KEYS is not set +# CONFIG_SECURITY is not set + +# +# Cryptographic options +# +CONFIG_CRYPTO=y +# CONFIG_CRYPTO_HMAC is not set +# CONFIG_CRYPTO_NULL is not set +# CONFIG_CRYPTO_MD4 is not set +CONFIG_CRYPTO_MD5=y +# CONFIG_CRYPTO_SHA1 is not set +# CONFIG_CRYPTO_SHA256 is not set +# CONFIG_CRYPTO_SHA512 is not set +# CONFIG_CRYPTO_WP512 is not set +# CONFIG_CRYPTO_TGR192 is not set +CONFIG_CRYPTO_DES=y +# CONFIG_CRYPTO_BLOWFISH is not set +# CONFIG_CRYPTO_TWOFISH is not set +# CONFIG_CRYPTO_SERPENT is not set +# CONFIG_CRYPTO_AES is not set +# CONFIG_CRYPTO_CAST5 is not set +# CONFIG_CRYPTO_CAST6 is not set +# CONFIG_CRYPTO_TEA is not set +# CONFIG_CRYPTO_ARC4 is not set +# CONFIG_CRYPTO_KHAZAD is not set +# CONFIG_CRYPTO_ANUBIS is not set +# CONFIG_CRYPTO_DEFLATE is not set +# CONFIG_CRYPTO_MICHAEL_MIC is not set +# CONFIG_CRYPTO_CRC32C is not set +# CONFIG_CRYPTO_TEST is not set + +# +# Hardware crypto devices +# + +# +# Library routines +# +# CONFIG_CRC_CCITT is not set +# CONFIG_CRC16 is not set +CONFIG_CRC32=y +# CONFIG_LIBCRC32C is not set +CONFIG_ZLIB_INFLATE=y diff --git a/arch/arm/configs/csb637_defconfig b/arch/arm/configs/csb637_defconfig new file mode 100644 index 000000000000..95a96a5462a0 --- /dev/null +++ b/arch/arm/configs/csb637_defconfig @@ -0,0 +1,1116 @@ +# +# Automatically generated make config: don't edit +# Linux kernel version: 2.6.15 +# Mon Jan 9 21:52:00 2006 +# +CONFIG_ARM=y +CONFIG_MMU=y +CONFIG_UID16=y +CONFIG_RWSEM_GENERIC_SPINLOCK=y +CONFIG_GENERIC_CALIBRATE_DELAY=y + +# +# Code maturity level options +# +CONFIG_EXPERIMENTAL=y +CONFIG_CLEAN_COMPILE=y +CONFIG_BROKEN_ON_SMP=y +CONFIG_INIT_ENV_ARG_LIMIT=32 + +# +# General setup +# +CONFIG_LOCALVERSION="" +CONFIG_LOCALVERSION_AUTO=y +# CONFIG_SWAP is not set +CONFIG_SYSVIPC=y +# CONFIG_POSIX_MQUEUE is not set +# CONFIG_BSD_PROCESS_ACCT is not set +CONFIG_SYSCTL=y +# CONFIG_AUDIT is not set +CONFIG_HOTPLUG=y +CONFIG_KOBJECT_UEVENT=y +# CONFIG_IKCONFIG is not set +CONFIG_INITRAMFS_SOURCE="" +CONFIG_CC_OPTIMIZE_FOR_SIZE=y +# CONFIG_EMBEDDED is not set +CONFIG_KALLSYMS=y +# CONFIG_KALLSYMS_ALL is not set +# CONFIG_KALLSYMS_EXTRA_PASS is not set +CONFIG_PRINTK=y +CONFIG_BUG=y +CONFIG_BASE_FULL=y +CONFIG_FUTEX=y +CONFIG_EPOLL=y +CONFIG_SHMEM=y +CONFIG_CC_ALIGN_FUNCTIONS=0 +CONFIG_CC_ALIGN_LABELS=0 +CONFIG_CC_ALIGN_LOOPS=0 +CONFIG_CC_ALIGN_JUMPS=0 +# CONFIG_TINY_SHMEM is not set +CONFIG_BASE_SMALL=0 + +# +# Loadable module support +# +CONFIG_MODULES=y +CONFIG_MODULE_UNLOAD=y +# CONFIG_MODULE_FORCE_UNLOAD is not set +CONFIG_OBSOLETE_MODPARM=y +# CONFIG_MODVERSIONS is not set +# CONFIG_MODULE_SRCVERSION_ALL is not set +CONFIG_KMOD=y + +# +# Block layer +# + +# +# IO Schedulers +# +CONFIG_IOSCHED_NOOP=y +CONFIG_IOSCHED_AS=y +CONFIG_IOSCHED_DEADLINE=y +CONFIG_IOSCHED_CFQ=y +CONFIG_DEFAULT_AS=y +# CONFIG_DEFAULT_DEADLINE is not set +# CONFIG_DEFAULT_CFQ is not set +# CONFIG_DEFAULT_NOOP is not set +CONFIG_DEFAULT_IOSCHED="anticipatory" + +# +# System Type +# +# CONFIG_ARCH_CLPS7500 is not set +# CONFIG_ARCH_CLPS711X is not set +# CONFIG_ARCH_CO285 is not set +# CONFIG_ARCH_EBSA110 is not set +# CONFIG_ARCH_CAMELOT is not set +# CONFIG_ARCH_FOOTBRIDGE is not set +# CONFIG_ARCH_INTEGRATOR is not set +# CONFIG_ARCH_IOP3XX is not set +# CONFIG_ARCH_IXP4XX is not set +# CONFIG_ARCH_IXP2000 is not set +# CONFIG_ARCH_L7200 is not set +# CONFIG_ARCH_PXA is not set +# CONFIG_ARCH_RPC is not set +# CONFIG_ARCH_SA1100 is not set +# CONFIG_ARCH_S3C2410 is not set +# CONFIG_ARCH_SHARK is not set +# CONFIG_ARCH_LH7A40X is not set +# CONFIG_ARCH_OMAP is not set +# CONFIG_ARCH_VERSATILE is not set +# CONFIG_ARCH_REALVIEW is not set +# CONFIG_ARCH_IMX is not set +# CONFIG_ARCH_H720X is not set +# CONFIG_ARCH_AAEC2000 is not set +CONFIG_ARCH_AT91RM9200=y + +# +# AT91RM9200 Implementations +# + +# +# AT91RM9200 Board Type +# +# CONFIG_ARCH_AT91RM9200DK is not set +# CONFIG_MACH_AT91RM9200EK is not set +# CONFIG_MACH_CSB337 is not set +CONFIG_MACH_CSB637=y +# CONFIG_MACH_CARMEVA is not set +# CONFIG_MACH_KB9200 is not set +# CONFIG_MACH_ATEB9200 is not set + +# +# AT91RM9200 Feature Selections +# +CONFIG_AT91_PROGRAMMABLE_CLOCKS=y + +# +# Processor Type +# +CONFIG_CPU_32=y +CONFIG_CPU_ARM920T=y +CONFIG_CPU_32v4=y +CONFIG_CPU_ABRT_EV4T=y +CONFIG_CPU_CACHE_V4WT=y +CONFIG_CPU_CACHE_VIVT=y +CONFIG_CPU_COPY_V4WB=y +CONFIG_CPU_TLB_V4WBI=y + +# +# Processor Features +# +# CONFIG_ARM_THUMB is not set +# CONFIG_CPU_ICACHE_DISABLE is not set +# CONFIG_CPU_DCACHE_DISABLE is not set +# CONFIG_CPU_DCACHE_WRITETHROUGH is not set + +# +# Bus support +# +CONFIG_ISA_DMA_API=y + +# +# PCCARD (PCMCIA/CardBus) support +# +CONFIG_PCCARD=y +# CONFIG_PCMCIA_DEBUG is not set +CONFIG_PCMCIA=y +CONFIG_PCMCIA_LOAD_CIS=y +CONFIG_PCMCIA_IOCTL=y + +# +# PC-card bridges +# +CONFIG_AT91_CF=y + +# +# Kernel Features +# +# CONFIG_PREEMPT is not set +# CONFIG_NO_IDLE_HZ is not set +# CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set +CONFIG_SELECT_MEMORY_MODEL=y +CONFIG_FLATMEM_MANUAL=y +# CONFIG_DISCONTIGMEM_MANUAL is not set +# CONFIG_SPARSEMEM_MANUAL is not set +CONFIG_FLATMEM=y +CONFIG_FLAT_NODE_MEM_MAP=y +# CONFIG_SPARSEMEM_STATIC is not set +CONFIG_SPLIT_PTLOCK_CPUS=4096 +CONFIG_LEDS=y +CONFIG_LEDS_TIMER=y +CONFIG_LEDS_CPU=y +CONFIG_ALIGNMENT_TRAP=y + +# +# Boot options +# +CONFIG_ZBOOT_ROM_TEXT=0x0 +CONFIG_ZBOOT_ROM_BSS=0x0 +CONFIG_CMDLINE="mem=32M console=ttyS0,38400 initrd=0x20410000,3145728 root=/dev/ram0 rw" +# CONFIG_XIP_KERNEL is not set + +# +# Floating point emulation +# + +# +# At least one emulation must be selected +# +CONFIG_FPE_NWFPE=y +# CONFIG_FPE_NWFPE_XP is not set +# CONFIG_FPE_FASTFPE is not set + +# +# Userspace binary formats +# +CONFIG_BINFMT_ELF=y +# CONFIG_BINFMT_AOUT is not set +# CONFIG_BINFMT_MISC is not set +# CONFIG_ARTHUR is not set + +# +# Power management options +# +# CONFIG_PM is not set + +# +# Networking +# +CONFIG_NET=y + +# +# Networking options +# +CONFIG_PACKET=y +# CONFIG_PACKET_MMAP is not set +CONFIG_UNIX=y +# CONFIG_NET_KEY is not set +CONFIG_INET=y +# CONFIG_IP_MULTICAST is not set +# CONFIG_IP_ADVANCED_ROUTER is not set +CONFIG_IP_FIB_HASH=y +CONFIG_IP_PNP=y +CONFIG_IP_PNP_DHCP=y +CONFIG_IP_PNP_BOOTP=y +# CONFIG_IP_PNP_RARP is not set +# CONFIG_NET_IPIP is not set +# CONFIG_NET_IPGRE is not set +# CONFIG_ARPD is not set +# CONFIG_SYN_COOKIES is not set +# CONFIG_INET_AH is not set +# CONFIG_INET_ESP is not set +# CONFIG_INET_IPCOMP is not set +# CONFIG_INET_TUNNEL is not set +CONFIG_INET_DIAG=y +CONFIG_INET_TCP_DIAG=y +# CONFIG_TCP_CONG_ADVANCED is not set +CONFIG_TCP_CONG_BIC=y +# CONFIG_IPV6 is not set +# CONFIG_NETFILTER is not set + +# +# DCCP Configuration (EXPERIMENTAL) +# +# CONFIG_IP_DCCP is not set + +# +# SCTP Configuration (EXPERIMENTAL) +# +# CONFIG_IP_SCTP is not set +# CONFIG_ATM is not set +# CONFIG_BRIDGE is not set +# CONFIG_VLAN_8021Q is not set +# CONFIG_DECNET is not set +# CONFIG_LLC2 is not set +# CONFIG_IPX is not set +# CONFIG_ATALK is not set +# CONFIG_X25 is not set +# CONFIG_LAPB is not set +# CONFIG_NET_DIVERT is not set +# CONFIG_ECONET is not set +# CONFIG_WAN_ROUTER is not set + +# +# QoS and/or fair queueing +# +# CONFIG_NET_SCHED is not set + +# +# Network testing +# +# CONFIG_NET_PKTGEN is not set +# CONFIG_HAMRADIO is not set +# CONFIG_IRDA is not set +# CONFIG_BT is not set +# CONFIG_IEEE80211 is not set + +# +# Device Drivers +# + +# +# Generic Driver Options +# +CONFIG_STANDALONE=y +CONFIG_PREVENT_FIRMWARE_BUILD=y +CONFIG_FW_LOADER=y +# CONFIG_DEBUG_DRIVER is not set + +# +# Connector - unified userspace <-> kernelspace linker +# +# CONFIG_CONNECTOR is not set + +# +# Memory Technology Devices (MTD) +# +CONFIG_MTD=y +# CONFIG_MTD_DEBUG is not set +# CONFIG_MTD_CONCAT is not set +CONFIG_MTD_PARTITIONS=y +# CONFIG_MTD_REDBOOT_PARTS is not set +CONFIG_MTD_CMDLINE_PARTS=y +# CONFIG_MTD_AFS_PARTS is not set + +# +# User Modules And Translation Layers +# +CONFIG_MTD_CHAR=y +CONFIG_MTD_BLOCK=y +# CONFIG_FTL is not set +# CONFIG_NFTL is not set +# CONFIG_INFTL is not set +# CONFIG_RFD_FTL is not set + +# +# RAM/ROM/Flash chip drivers +# +CONFIG_MTD_CFI=y +# CONFIG_MTD_JEDECPROBE is not set +CONFIG_MTD_GEN_PROBE=y +# CONFIG_MTD_CFI_ADV_OPTIONS is not set +CONFIG_MTD_MAP_BANK_WIDTH_1=y +CONFIG_MTD_MAP_BANK_WIDTH_2=y +CONFIG_MTD_MAP_BANK_WIDTH_4=y +# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set +CONFIG_MTD_CFI_I1=y +CONFIG_MTD_CFI_I2=y +# CONFIG_MTD_CFI_I4 is not set +# CONFIG_MTD_CFI_I8 is not set +CONFIG_MTD_CFI_INTELEXT=y +# CONFIG_MTD_CFI_AMDSTD is not set +# CONFIG_MTD_CFI_STAA is not set +CONFIG_MTD_CFI_UTIL=y +# CONFIG_MTD_RAM is not set +# CONFIG_MTD_ROM is not set +# CONFIG_MTD_ABSENT is not set +# CONFIG_MTD_XIP is not set + +# +# Mapping drivers for chip access +# +# CONFIG_MTD_COMPLEX_MAPPINGS is not set +# CONFIG_MTD_PHYSMAP is not set +# CONFIG_MTD_ARM_INTEGRATOR is not set +# CONFIG_MTD_PLATRAM is not set +CONFIG_MTD_CSB637=y + +# +# Self-contained MTD device drivers +# +# CONFIG_MTD_SLRAM is not set +# CONFIG_MTD_PHRAM is not set +# CONFIG_MTD_MTDRAM is not set +# CONFIG_MTD_BLKMTD is not set +# CONFIG_MTD_BLOCK2MTD is not set + +# +# Disk-On-Chip Device Drivers +# +# CONFIG_MTD_DOC2000 is not set +# CONFIG_MTD_DOC2001 is not set +# CONFIG_MTD_DOC2001PLUS is not set +# CONFIG_MTD_AT91_DATAFLASH is not set + +# +# NAND Flash Device Drivers +# +# CONFIG_MTD_NAND is not set + +# +# OneNAND Flash Device Drivers +# +# CONFIG_MTD_ONENAND is not set + +# +# Parallel port support +# +# CONFIG_PARPORT is not set + +# +# Plug and Play support +# + +# +# Block devices +# +# CONFIG_BLK_DEV_COW_COMMON is not set +CONFIG_BLK_DEV_LOOP=y +# CONFIG_BLK_DEV_CRYPTOLOOP is not set +# CONFIG_BLK_DEV_NBD is not set +# CONFIG_BLK_DEV_UB is not set +CONFIG_BLK_DEV_RAM=y +CONFIG_BLK_DEV_RAM_COUNT=16 +CONFIG_BLK_DEV_RAM_SIZE=8192 +CONFIG_BLK_DEV_INITRD=y +# CONFIG_CDROM_PKTCDVD is not set +# CONFIG_ATA_OVER_ETH is not set + +# +# ATA/ATAPI/MFM/RLL support +# +# CONFIG_IDE is not set + +# +# SCSI device support +# +# CONFIG_RAID_ATTRS is not set +CONFIG_SCSI=y +CONFIG_SCSI_PROC_FS=y + +# +# SCSI support type (disk, tape, CD-ROM) +# +# CONFIG_BLK_DEV_SD is not set +# CONFIG_CHR_DEV_ST is not set +# CONFIG_CHR_DEV_OSST is not set +# CONFIG_BLK_DEV_SR is not set +# CONFIG_CHR_DEV_SG is not set +# CONFIG_CHR_DEV_SCH is not set + +# +# Some SCSI devices (e.g. CD jukebox) support multiple LUNs +# +# CONFIG_SCSI_MULTI_LUN is not set +# CONFIG_SCSI_CONSTANTS is not set +# CONFIG_SCSI_LOGGING is not set + +# +# SCSI Transport Attributes +# +# CONFIG_SCSI_SPI_ATTRS is not set +# CONFIG_SCSI_FC_ATTRS is not set +# CONFIG_SCSI_ISCSI_ATTRS is not set +# CONFIG_SCSI_SAS_ATTRS is not set + +# +# SCSI low-level drivers +# +# CONFIG_ISCSI_TCP is not set +# CONFIG_SCSI_SATA is not set +# CONFIG_SCSI_DEBUG is not set + +# +# PCMCIA SCSI adapter support +# +# CONFIG_PCMCIA_AHA152X is not set +# CONFIG_PCMCIA_FDOMAIN is not set +# CONFIG_PCMCIA_NINJA_SCSI is not set +# CONFIG_PCMCIA_QLOGIC is not set +# CONFIG_PCMCIA_SYM53C500 is not set + +# +# Multi-device support (RAID and LVM) +# +# CONFIG_MD is not set + +# +# Fusion MPT device support +# +# CONFIG_FUSION is not set + +# +# IEEE 1394 (FireWire) support +# + +# +# I2O device support +# + +# +# Network device support +# +CONFIG_NETDEVICES=y +# CONFIG_DUMMY is not set +# CONFIG_BONDING is not set +# CONFIG_EQUALIZER is not set +# CONFIG_TUN is not set + +# +# PHY device support +# +# CONFIG_PHYLIB is not set + +# +# Ethernet (10 or 100Mbit) +# +CONFIG_NET_ETHERNET=y +CONFIG_MII=y +CONFIG_ARM_AT91_ETHER=y +# CONFIG_SMC91X is not set +# CONFIG_DM9000 is not set + +# +# Ethernet (1000 Mbit) +# + +# +# Ethernet (10000 Mbit) +# + +# +# Token Ring devices +# + +# +# Wireless LAN (non-hamradio) +# +# CONFIG_NET_RADIO is not set + +# +# PCMCIA network device support +# +# CONFIG_NET_PCMCIA is not set + +# +# Wan interfaces +# +# CONFIG_WAN is not set +# CONFIG_PPP is not set +# CONFIG_SLIP is not set +# CONFIG_SHAPER is not set +# CONFIG_NETCONSOLE is not set +# CONFIG_NETPOLL is not set +# CONFIG_NET_POLL_CONTROLLER is not set + +# +# ISDN subsystem +# +# CONFIG_ISDN is not set + +# +# Input device support +# +CONFIG_INPUT=y + +# +# Userland interfaces +# +CONFIG_INPUT_MOUSEDEV=y +CONFIG_INPUT_MOUSEDEV_PSAUX=y +CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024 +CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 +# CONFIG_INPUT_JOYDEV is not set +# CONFIG_INPUT_TSDEV is not set +# CONFIG_INPUT_EVDEV is not set +# CONFIG_INPUT_EVBUG is not set + +# +# Input Device Drivers +# +# CONFIG_INPUT_KEYBOARD is not set +# CONFIG_INPUT_MOUSE is not set +# CONFIG_INPUT_JOYSTICK is not set +# CONFIG_INPUT_TOUCHSCREEN is not set +# CONFIG_INPUT_MISC is not set + +# +# Hardware I/O ports +# +# CONFIG_SERIO is not set +# CONFIG_GAMEPORT is not set + +# +# Character devices +# +CONFIG_VT=y +CONFIG_VT_CONSOLE=y +CONFIG_HW_CONSOLE=y +# CONFIG_SERIAL_NONSTANDARD is not set + +# +# Serial drivers +# +# CONFIG_SERIAL_8250 is not set + +# +# Non-8250 serial port support +# +CONFIG_SERIAL_AT91=y +CONFIG_SERIAL_AT91_CONSOLE=y +# CONFIG_SERIAL_AT91_TTYAT is not set +CONFIG_SERIAL_CORE=y +CONFIG_SERIAL_CORE_CONSOLE=y +CONFIG_UNIX98_PTYS=y +CONFIG_LEGACY_PTYS=y +CONFIG_LEGACY_PTY_COUNT=256 + +# +# IPMI +# +# CONFIG_IPMI_HANDLER is not set + +# +# Watchdog Cards +# +CONFIG_WATCHDOG=y +CONFIG_WATCHDOG_NOWAYOUT=y + +# +# Watchdog Device Drivers +# +# CONFIG_SOFT_WATCHDOG is not set +CONFIG_AT91_WATCHDOG=y + +# +# USB-based Watchdog Cards +# +# CONFIG_USBPCWATCHDOG is not set +# CONFIG_NVRAM is not set +CONFIG_RTC=y +# CONFIG_AT91_RTC is not set +# CONFIG_DTLK is not set +# CONFIG_R3964 is not set + +# +# Ftape, the floppy tape device driver +# + +# +# PCMCIA character devices +# +# CONFIG_SYNCLINK_CS is not set +# CONFIG_CARDMAN_4000 is not set +# CONFIG_CARDMAN_4040 is not set +# CONFIG_RAW_DRIVER is not set + +# +# TPM devices +# +# CONFIG_TCG_TPM is not set +# CONFIG_TELCLOCK is not set +CONFIG_AT91_SPI=y +CONFIG_AT91_SPIDEV=y + +# +# I2C support +# +CONFIG_I2C=y +CONFIG_I2C_CHARDEV=y + +# +# I2C Algorithms +# +# CONFIG_I2C_ALGOBIT is not set +# CONFIG_I2C_ALGOPCF is not set +# CONFIG_I2C_ALGOPCA is not set + +# +# I2C Hardware Bus support +# +CONFIG_I2C_AT91=y +# CONFIG_I2C_PARPORT_LIGHT is not set +# CONFIG_I2C_STUB is not set +# CONFIG_I2C_PCA_ISA is not set + +# +# Miscellaneous I2C Chip support +# +# CONFIG_SENSORS_DS1337 is not set +# CONFIG_SENSORS_DS1374 is not set +# CONFIG_SENSORS_EEPROM is not set +# CONFIG_SENSORS_PCF8574 is not set +# CONFIG_SENSORS_PCA9539 is not set +# CONFIG_SENSORS_PCF8591 is not set +# CONFIG_SENSORS_RTC8564 is not set +# CONFIG_SENSORS_MAX6875 is not set +# CONFIG_RTC_X1205_I2C is not set +# CONFIG_I2C_DEBUG_CORE is not set +# CONFIG_I2C_DEBUG_ALGO is not set +# CONFIG_I2C_DEBUG_BUS is not set +# CONFIG_I2C_DEBUG_CHIP is not set + +# +# Hardware Monitoring support +# +CONFIG_HWMON=y +# CONFIG_HWMON_VID is not set +# CONFIG_SENSORS_ADM1021 is not set +# CONFIG_SENSORS_ADM1025 is not set +# CONFIG_SENSORS_ADM1026 is not set +# CONFIG_SENSORS_ADM1031 is not set +# CONFIG_SENSORS_ADM9240 is not set +# CONFIG_SENSORS_ASB100 is not set +# CONFIG_SENSORS_ATXP1 is not set +# CONFIG_SENSORS_DS1621 is not set +# CONFIG_SENSORS_FSCHER is not set +# CONFIG_SENSORS_FSCPOS is not set +# CONFIG_SENSORS_GL518SM is not set +# CONFIG_SENSORS_GL520SM is not set +# CONFIG_SENSORS_IT87 is not set +# CONFIG_SENSORS_LM63 is not set +# CONFIG_SENSORS_LM75 is not set +# CONFIG_SENSORS_LM77 is not set +# CONFIG_SENSORS_LM78 is not set +# CONFIG_SENSORS_LM80 is not set +# CONFIG_SENSORS_LM83 is not set +# CONFIG_SENSORS_LM85 is not set +# CONFIG_SENSORS_LM87 is not set +# CONFIG_SENSORS_LM90 is not set +# CONFIG_SENSORS_LM92 is not set +# CONFIG_SENSORS_MAX1619 is not set +# CONFIG_SENSORS_PC87360 is not set +# CONFIG_SENSORS_SMSC47M1 is not set +# CONFIG_SENSORS_SMSC47B397 is not set +# CONFIG_SENSORS_W83781D is not set +# CONFIG_SENSORS_W83792D is not set +# CONFIG_SENSORS_W83L785TS is not set +# CONFIG_SENSORS_W83627HF is not set +# CONFIG_SENSORS_W83627EHF is not set +# CONFIG_HWMON_DEBUG_CHIP is not set + +# +# Misc devices +# + +# +# Multimedia Capabilities Port drivers +# + +# +# Multimedia devices +# +# CONFIG_VIDEO_DEV is not set + +# +# Digital Video Broadcasting Devices +# +# CONFIG_DVB is not set + +# +# Graphics support +# +# CONFIG_FB is not set + +# +# Console display driver support +# +# CONFIG_VGA_CONSOLE is not set +CONFIG_DUMMY_CONSOLE=y + +# +# Sound +# +# CONFIG_SOUND is not set + +# +# USB support +# +CONFIG_USB_ARCH_HAS_HCD=y +CONFIG_USB_ARCH_HAS_OHCI=y +CONFIG_USB=y +CONFIG_USB_DEBUG=y + +# +# Miscellaneous USB options +# +CONFIG_USB_DEVICEFS=y +# CONFIG_USB_BANDWIDTH is not set +# CONFIG_USB_DYNAMIC_MINORS is not set +# CONFIG_USB_OTG is not set + +# +# USB Host Controller Drivers +# +# CONFIG_USB_ISP116X_HCD is not set +CONFIG_USB_OHCI_HCD=y +# CONFIG_USB_OHCI_BIG_ENDIAN is not set +CONFIG_USB_OHCI_LITTLE_ENDIAN=y +# CONFIG_USB_SL811_HCD is not set + +# +# USB Device Class drivers +# +# CONFIG_USB_ACM is not set +# CONFIG_USB_PRINTER is not set + +# +# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' +# + +# +# may also be needed; see USB_STORAGE Help for more information +# +CONFIG_USB_STORAGE=y +# CONFIG_USB_STORAGE_DEBUG is not set +# CONFIG_USB_STORAGE_DATAFAB is not set +# CONFIG_USB_STORAGE_FREECOM is not set +# CONFIG_USB_STORAGE_DPCM is not set +# CONFIG_USB_STORAGE_USBAT is not set +# CONFIG_USB_STORAGE_SDDR09 is not set +# CONFIG_USB_STORAGE_SDDR55 is not set +# CONFIG_USB_STORAGE_JUMPSHOT is not set + +# +# USB Input Devices +# +# CONFIG_USB_HID is not set + +# +# USB HID Boot Protocol drivers +# +# CONFIG_USB_KBD is not set +# CONFIG_USB_MOUSE is not set +# CONFIG_USB_AIPTEK is not set +# CONFIG_USB_WACOM is not set +# CONFIG_USB_ACECAD is not set +# CONFIG_USB_KBTAB is not set +# CONFIG_USB_POWERMATE is not set +# CONFIG_USB_MTOUCH is not set +# CONFIG_USB_ITMTOUCH is not set +# CONFIG_USB_EGALAX is not set +# CONFIG_USB_YEALINK is not set +# CONFIG_USB_XPAD is not set +# CONFIG_USB_ATI_REMOTE is not set +# CONFIG_USB_KEYSPAN_REMOTE is not set +# CONFIG_USB_APPLETOUCH is not set + +# +# USB Imaging devices +# +# CONFIG_USB_MDC800 is not set +# CONFIG_USB_MICROTEK is not set + +# +# USB Multimedia devices +# +# CONFIG_USB_DABUSB is not set + +# +# Video4Linux support is needed for USB Multimedia device support +# + +# +# USB Network Adapters +# +# CONFIG_USB_CATC is not set +# CONFIG_USB_KAWETH is not set +# CONFIG_USB_PEGASUS is not set +# CONFIG_USB_RTL8150 is not set +# CONFIG_USB_USBNET is not set +CONFIG_USB_MON=y + +# +# USB port drivers +# + +# +# USB Serial Converter support +# +CONFIG_USB_SERIAL=y +CONFIG_USB_SERIAL_CONSOLE=y +CONFIG_USB_SERIAL_GENERIC=y +# CONFIG_USB_SERIAL_AIRPRIME is not set +# CONFIG_USB_SERIAL_ANYDATA is not set +# CONFIG_USB_SERIAL_BELKIN is not set +# CONFIG_USB_SERIAL_WHITEHEAT is not set +# CONFIG_USB_SERIAL_DIGI_ACCELEPORT is not set +# CONFIG_USB_SERIAL_CP2101 is not set +# CONFIG_USB_SERIAL_CYPRESS_M8 is not set +# CONFIG_USB_SERIAL_EMPEG is not set +CONFIG_USB_SERIAL_FTDI_SIO=y +# CONFIG_USB_SERIAL_VISOR is not set +# CONFIG_USB_SERIAL_IPAQ is not set +# CONFIG_USB_SERIAL_IR is not set +# CONFIG_USB_SERIAL_EDGEPORT is not set +# CONFIG_USB_SERIAL_EDGEPORT_TI is not set +# CONFIG_USB_SERIAL_GARMIN is not set +# CONFIG_USB_SERIAL_IPW is not set +# CONFIG_USB_SERIAL_KEYSPAN_PDA is not set +CONFIG_USB_SERIAL_KEYSPAN=y +CONFIG_USB_SERIAL_KEYSPAN_MPR=y +CONFIG_USB_SERIAL_KEYSPAN_USA28=y +CONFIG_USB_SERIAL_KEYSPAN_USA28X=y +CONFIG_USB_SERIAL_KEYSPAN_USA28XA=y +CONFIG_USB_SERIAL_KEYSPAN_USA28XB=y +CONFIG_USB_SERIAL_KEYSPAN_USA19=y +CONFIG_USB_SERIAL_KEYSPAN_USA18X=y +CONFIG_USB_SERIAL_KEYSPAN_USA19W=y +CONFIG_USB_SERIAL_KEYSPAN_USA19QW=y +CONFIG_USB_SERIAL_KEYSPAN_USA19QI=y +CONFIG_USB_SERIAL_KEYSPAN_USA49W=y +CONFIG_USB_SERIAL_KEYSPAN_USA49WLC=y +# CONFIG_USB_SERIAL_KLSI is not set +# CONFIG_USB_SERIAL_KOBIL_SCT is not set +CONFIG_USB_SERIAL_MCT_U232=y +# CONFIG_USB_SERIAL_PL2303 is not set +# CONFIG_USB_SERIAL_HP4X is not set +# CONFIG_USB_SERIAL_SAFE is not set +# CONFIG_USB_SERIAL_TI is not set +# CONFIG_USB_SERIAL_CYBERJACK is not set +# CONFIG_USB_SERIAL_XIRCOM is not set +# CONFIG_USB_SERIAL_OPTION is not set +# CONFIG_USB_SERIAL_OMNINET is not set +CONFIG_USB_EZUSB=y + +# +# USB Miscellaneous drivers +# +# CONFIG_USB_EMI62 is not set +# CONFIG_USB_EMI26 is not set +# CONFIG_USB_AUERSWALD is not set +# CONFIG_USB_RIO500 is not set +# CONFIG_USB_LEGOTOWER is not set +# CONFIG_USB_LCD is not set +# CONFIG_USB_LED is not set +# CONFIG_USB_CYTHERM is not set +# CONFIG_USB_PHIDGETKIT is not set +# CONFIG_USB_PHIDGETSERVO is not set +# CONFIG_USB_IDMOUSE is not set +# CONFIG_USB_LD is not set +# CONFIG_USB_TEST is not set + +# +# USB DSL modem support +# + +# +# USB Gadget Support +# +# CONFIG_USB_GADGET is not set + +# +# MMC/SD Card support +# +# CONFIG_MMC is not set + +# +# File systems +# +CONFIG_EXT2_FS=y +# CONFIG_EXT2_FS_XATTR is not set +# CONFIG_EXT2_FS_XIP is not set +# CONFIG_EXT3_FS is not set +# CONFIG_JBD is not set +# CONFIG_REISERFS_FS is not set +# CONFIG_JFS_FS is not set +# CONFIG_FS_POSIX_ACL is not set +# CONFIG_XFS_FS is not set +# CONFIG_MINIX_FS is not set +# CONFIG_ROMFS_FS is not set +CONFIG_INOTIFY=y +# CONFIG_QUOTA is not set +CONFIG_DNOTIFY=y +# CONFIG_AUTOFS_FS is not set +# CONFIG_AUTOFS4_FS is not set +# CONFIG_FUSE_FS is not set + +# +# CD-ROM/DVD Filesystems +# +# CONFIG_ISO9660_FS is not set +# CONFIG_UDF_FS is not set + +# +# DOS/FAT/NT Filesystems +# +# CONFIG_MSDOS_FS is not set +# CONFIG_VFAT_FS is not set +# CONFIG_NTFS_FS is not set + +# +# Pseudo filesystems +# +CONFIG_PROC_FS=y +CONFIG_SYSFS=y +CONFIG_TMPFS=y +# CONFIG_HUGETLB_PAGE is not set +CONFIG_RAMFS=y +# CONFIG_RELAYFS_FS is not set + +# +# Miscellaneous filesystems +# +# CONFIG_ADFS_FS is not set +# CONFIG_AFFS_FS is not set +# CONFIG_HFS_FS is not set +# CONFIG_HFSPLUS_FS is not set +# CONFIG_BEFS_FS is not set +# CONFIG_BFS_FS is not set +# CONFIG_EFS_FS is not set +# CONFIG_JFFS_FS is not set +# CONFIG_JFFS2_FS is not set +CONFIG_CRAMFS=y +# CONFIG_VXFS_FS is not set +# CONFIG_HPFS_FS is not set +# CONFIG_QNX4FS_FS is not set +# CONFIG_SYSV_FS is not set +# CONFIG_UFS_FS is not set + +# +# Network File Systems +# +CONFIG_NFS_FS=y +CONFIG_NFS_V3=y +# CONFIG_NFS_V3_ACL is not set +CONFIG_NFS_V4=y +# CONFIG_NFS_DIRECTIO is not set +# CONFIG_NFSD is not set +CONFIG_ROOT_NFS=y +CONFIG_LOCKD=y +CONFIG_LOCKD_V4=y +CONFIG_NFS_COMMON=y +CONFIG_SUNRPC=y +CONFIG_SUNRPC_GSS=y +CONFIG_RPCSEC_GSS_KRB5=y +# CONFIG_RPCSEC_GSS_SPKM3 is not set +# CONFIG_SMB_FS is not set +# CONFIG_CIFS is not set +# CONFIG_NCP_FS is not set +# CONFIG_CODA_FS is not set +# CONFIG_AFS_FS is not set +# CONFIG_9P_FS is not set + +# +# Partition Types +# +# CONFIG_PARTITION_ADVANCED is not set +CONFIG_MSDOS_PARTITION=y + +# +# Native Language Support +# +# CONFIG_NLS is not set + +# +# Profiling support +# +# CONFIG_PROFILING is not set + +# +# Kernel hacking +# +# CONFIG_PRINTK_TIME is not set +CONFIG_DEBUG_KERNEL=y +# CONFIG_MAGIC_SYSRQ is not set +CONFIG_LOG_BUF_SHIFT=14 +CONFIG_DETECT_SOFTLOCKUP=y +# CONFIG_SCHEDSTATS is not set +# CONFIG_DEBUG_SLAB is not set +# CONFIG_DEBUG_SPINLOCK is not set +# CONFIG_DEBUG_SPINLOCK_SLEEP is not set +# CONFIG_DEBUG_KOBJECT is not set +CONFIG_DEBUG_BUGVERBOSE=y +# CONFIG_DEBUG_INFO is not set +# CONFIG_DEBUG_FS is not set +# CONFIG_DEBUG_VM is not set +CONFIG_FRAME_POINTER=y +# CONFIG_RCU_TORTURE_TEST is not set +CONFIG_DEBUG_USER=y +# CONFIG_DEBUG_WAITQ is not set +# CONFIG_DEBUG_ERRORS is not set +CONFIG_DEBUG_LL=y +# CONFIG_DEBUG_ICEDCC is not set + +# +# Security options +# +# CONFIG_KEYS is not set +# CONFIG_SECURITY is not set + +# +# Cryptographic options +# +CONFIG_CRYPTO=y +# CONFIG_CRYPTO_HMAC is not set +# CONFIG_CRYPTO_NULL is not set +# CONFIG_CRYPTO_MD4 is not set +CONFIG_CRYPTO_MD5=y +# CONFIG_CRYPTO_SHA1 is not set +# CONFIG_CRYPTO_SHA256 is not set +# CONFIG_CRYPTO_SHA512 is not set +# CONFIG_CRYPTO_WP512 is not set +# CONFIG_CRYPTO_TGR192 is not set +CONFIG_CRYPTO_DES=y +# CONFIG_CRYPTO_BLOWFISH is not set +# CONFIG_CRYPTO_TWOFISH is not set +# CONFIG_CRYPTO_SERPENT is not set +# CONFIG_CRYPTO_AES is not set +# CONFIG_CRYPTO_CAST5 is not set +# CONFIG_CRYPTO_CAST6 is not set +# CONFIG_CRYPTO_TEA is not set +# CONFIG_CRYPTO_ARC4 is not set +# CONFIG_CRYPTO_KHAZAD is not set +# CONFIG_CRYPTO_ANUBIS is not set +# CONFIG_CRYPTO_DEFLATE is not set +# CONFIG_CRYPTO_MICHAEL_MIC is not set +# CONFIG_CRYPTO_CRC32C is not set +# CONFIG_CRYPTO_TEST is not set + +# +# Hardware crypto devices +# + +# +# Library routines +# +# CONFIG_CRC_CCITT is not set +# CONFIG_CRC16 is not set +CONFIG_CRC32=y +# CONFIG_LIBCRC32C is not set +CONFIG_ZLIB_INFLATE=y diff --git a/arch/arm/kernel/ecard.c b/arch/arm/kernel/ecard.c index dceb826bd216..96fd91926c9b 100644 --- a/arch/arm/kernel/ecard.c +++ b/arch/arm/kernel/ecard.c @@ -40,6 +40,7 @@ #include #include #include +#include #include #include @@ -206,7 +207,7 @@ static void ecard_task_readbytes(struct ecard_request *req) static DECLARE_WAIT_QUEUE_HEAD(ecard_wait); static struct ecard_request *ecard_req; -static DECLARE_MUTEX(ecard_sem); +static DEFINE_MUTEX(ecard_mutex); /* * Set up the expansion card daemon's page tables. @@ -299,7 +300,7 @@ static void ecard_call(struct ecard_request *req) req->complete = &completion; - down(&ecard_sem); + mutex_lock(&ecard_mutex); ecard_req = req; wake_up(&ecard_wait); @@ -307,7 +308,7 @@ static void ecard_call(struct ecard_request *req) * Now wait for kecardd to run. */ wait_for_completion(&completion); - up(&ecard_sem); + mutex_unlock(&ecard_mutex); } /* ======================= Mid-level card control ===================== */ diff --git a/arch/arm/kernel/fiq.c b/arch/arm/kernel/fiq.c index 9299dfc25698..1ec3f7faa259 100644 --- a/arch/arm/kernel/fiq.c +++ b/arch/arm/kernel/fiq.c @@ -101,7 +101,7 @@ void __attribute__((naked)) set_fiq_regs(struct pt_regs *regs) ldmia %1, {r8 - r14}\n\ msr cpsr_c, %0 @ return to SVC mode\n\ mov r0, r0\n\ - ldmea fp, {fp, sp, pc}" + ldmfd sp, {fp, sp, pc}" : "=&r" (tmp) : "r" (®s->ARM_r8), "I" (PSR_I_BIT | PSR_F_BIT | FIQ_MODE)); } @@ -119,7 +119,7 @@ void __attribute__((naked)) get_fiq_regs(struct pt_regs *regs) stmia %1, {r8 - r14}\n\ msr cpsr_c, %0 @ return to SVC mode\n\ mov r0, r0\n\ - ldmea fp, {fp, sp, pc}" + ldmfd sp, {fp, sp, pc}" : "=&r" (tmp) : "r" (®s->ARM_r8), "I" (PSR_I_BIT | PSR_F_BIT | FIQ_MODE)); } diff --git a/arch/arm/kernel/setup.c b/arch/arm/kernel/setup.c index 2cab741ad0f8..c45d10d07bde 100644 --- a/arch/arm/kernel/setup.c +++ b/arch/arm/kernel/setup.c @@ -205,7 +205,7 @@ static const char *proc_arch[] = { "5TE", "5TEJ", "6TEJ", - "?(10)", + "7", "?(11)", "?(12)", "?(13)", @@ -258,14 +258,17 @@ int cpu_architecture(void) { int cpu_arch; - if ((processor_id & 0x0000f000) == 0) { + if ((processor_id & 0x0008f000) == 0) { cpu_arch = CPU_ARCH_UNKNOWN; - } else if ((processor_id & 0x0000f000) == 0x00007000) { + } else if ((processor_id & 0x0008f000) == 0x00007000) { cpu_arch = (processor_id & (1 << 23)) ? CPU_ARCH_ARMv4T : CPU_ARCH_ARMv3; - } else { + } else if ((processor_id & 0x00080000) == 0x00000000) { cpu_arch = (processor_id >> 16) & 7; if (cpu_arch) cpu_arch += CPU_ARCH_ARMv3; + } else { + /* the revised CPUID */ + cpu_arch = ((processor_id >> 12) & 0xf) - 0xb + CPU_ARCH_ARMv6; } return cpu_arch; @@ -863,11 +866,11 @@ static int c_show(struct seq_file *m, void *v) seq_printf(m, "\nCPU implementer\t: 0x%02x\n", processor_id >> 24); seq_printf(m, "CPU architecture: %s\n", proc_arch[cpu_architecture()]); - if ((processor_id & 0x0000f000) == 0x00000000) { + if ((processor_id & 0x0008f000) == 0x00000000) { /* pre-ARM7 */ seq_printf(m, "CPU part\t\t: %07x\n", processor_id >> 4); } else { - if ((processor_id & 0x0000f000) == 0x00007000) { + if ((processor_id & 0x0008f000) == 0x00007000) { /* ARM7 */ seq_printf(m, "CPU variant\t: 0x%02x\n", (processor_id >> 16) & 127); diff --git a/arch/arm/lib/csumpartialcopy.S b/arch/arm/lib/csumpartialcopy.S index 990ee63b2465..21effe0dbf97 100644 --- a/arch/arm/lib/csumpartialcopy.S +++ b/arch/arm/lib/csumpartialcopy.S @@ -18,11 +18,13 @@ */ .macro save_regs + mov ip, sp stmfd sp!, {r1, r4 - r8, fp, ip, lr, pc} + sub fp, ip, #4 .endm - .macro load_regs,flags - LOADREGS(\flags,fp,{r1, r4 - r8, fp, sp, pc}) + .macro load_regs + ldmfd sp, {r1, r4 - r8, fp, sp, pc} .endm .macro load1b, reg1 diff --git a/arch/arm/lib/csumpartialcopygeneric.S b/arch/arm/lib/csumpartialcopygeneric.S index 4a4609c19095..c50e8f5285d1 100644 --- a/arch/arm/lib/csumpartialcopygeneric.S +++ b/arch/arm/lib/csumpartialcopygeneric.S @@ -23,7 +23,7 @@ len .req r2 sum .req r3 .Lzero: mov r0, sum - load_regs ea + load_regs /* * Align an unaligned destination pointer. We know that @@ -87,9 +87,7 @@ sum .req r3 b .Ldone FN_ENTRY - mov ip, sp save_regs - sub fp, ip, #4 cmp len, #8 @ Ensure that we have at least blo .Lless8 @ 8 bytes to copy. @@ -163,7 +161,7 @@ FN_ENTRY ldr sum, [sp, #0] @ dst tst sum, #1 movne r0, r0, ror #8 - load_regs ea + load_regs .Lsrc_not_aligned: adc sum, sum, #0 @ include C from dst alignment diff --git a/arch/arm/lib/csumpartialcopyuser.S b/arch/arm/lib/csumpartialcopyuser.S index 333bca292de9..c3b93e22ea25 100644 --- a/arch/arm/lib/csumpartialcopyuser.S +++ b/arch/arm/lib/csumpartialcopyuser.S @@ -18,11 +18,13 @@ .text .macro save_regs + mov ip, sp stmfd sp!, {r1 - r2, r4 - r8, fp, ip, lr, pc} + sub fp, ip, #4 .endm - .macro load_regs,flags - ldm\flags fp, {r1, r2, r4-r8, fp, sp, pc} + .macro load_regs + ldmfd sp, {r1, r2, r4-r8, fp, sp, pc} .endm .macro load1b, reg1 @@ -100,5 +102,5 @@ 6002: teq r2, r1 strneb r0, [r1], #1 bne 6002b - load_regs ea + load_regs .previous diff --git a/arch/arm/mach-aaec2000/clock.c b/arch/arm/mach-aaec2000/clock.c index 1c84c60941e1..74aa7a39bb68 100644 --- a/arch/arm/mach-aaec2000/clock.c +++ b/arch/arm/mach-aaec2000/clock.c @@ -16,26 +16,27 @@ #include #include #include +#include #include #include "clock.h" static LIST_HEAD(clocks); -static DECLARE_MUTEX(clocks_sem); +static DEFINE_MUTEX(clocks_mutex); struct clk *clk_get(struct device *dev, const char *id) { struct clk *p, *clk = ERR_PTR(-ENOENT); - down(&clocks_sem); + mutex_lock(&clocks_mutex); list_for_each_entry(p, &clocks, node) { if (strcmp(id, p->name) == 0 && try_module_get(p->owner)) { clk = p; break; } } - up(&clocks_sem); + mutex_unlock(&clocks_mutex); return clk; } @@ -78,18 +79,18 @@ EXPORT_SYMBOL(clk_set_rate); int clk_register(struct clk *clk) { - down(&clocks_sem); + mutex_lock(&clocks_mutex); list_add(&clk->node, &clocks); - up(&clocks_sem); + mutex_unlock(&clocks_mutex); return 0; } EXPORT_SYMBOL(clk_register); void clk_unregister(struct clk *clk) { - down(&clocks_sem); + mutex_lock(&clocks_mutex); list_del(&clk->node); - up(&clocks_sem); + mutex_unlock(&clocks_mutex); } EXPORT_SYMBOL(clk_unregister); diff --git a/arch/arm/mach-at91rm9200/Makefile b/arch/arm/mach-at91rm9200/Makefile index 1f2805ca6e21..75e6ee318ded 100644 --- a/arch/arm/mach-at91rm9200/Makefile +++ b/arch/arm/mach-at91rm9200/Makefile @@ -8,10 +8,10 @@ obj-n := obj- := # Board-specific support -#obj-$(CONFIG_ARCH_AT91RM9200DK) += board-dk.o -#obj-$(CONFIG_MACH_AT91RM9200EK) += board-ek.o -#obj-$(CONFIG_MACH_CSB337) += board-csb337.o -#obj-$(CONFIG_MACH_CSB637) += board-csb637.o +obj-$(CONFIG_ARCH_AT91RM9200DK) += board-dk.o +obj-$(CONFIG_MACH_AT91RM9200EK) += board-ek.o +obj-$(CONFIG_MACH_CSB337) += board-csb337.o +obj-$(CONFIG_MACH_CSB637) += board-csb637.o #obj-$(CONFIG_MACH_CARMEVA) += board-carmeva.o #obj-$(CONFIG_MACH_KB9200) += board-kb9202.o diff --git a/arch/arm/mach-at91rm9200/board-csb337.c b/arch/arm/mach-at91rm9200/board-csb337.c new file mode 100644 index 000000000000..4aec834ee47f --- /dev/null +++ b/arch/arm/mach-at91rm9200/board-csb337.c @@ -0,0 +1,143 @@ +/* + * linux/arch/arm/mach-at91rm9200/board-csb337.c + * + * Copyright (C) 2005 SAN People + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#include +#include +#include +#include +#include +#include + +#include +#include +#include +#include + +#include +#include +#include + +#include +#include +#include + +#include "generic.h" + +static void __init csb337_init_irq(void) +{ + /* Initialize AIC controller */ + at91rm9200_init_irq(NULL); + + /* Set up the GPIO interrupts */ + at91_gpio_irq_setup(BGA_GPIO_BANKS); +} + +/* + * Serial port configuration. + * 0 .. 3 = USART0 .. USART3 + * 4 = DBGU + */ +#define CSB337_UART_MAP { 4, 1, -1, -1, -1 } /* ttyS0, ..., ttyS4 */ +#define CSB337_SERIAL_CONSOLE 0 /* ttyS0 */ + +static void __init csb337_map_io(void) +{ + int serial[AT91_NR_UART] = CSB337_UART_MAP; + int i; + + at91rm9200_map_io(); + + /* Initialize clocks: 3.6864 MHz crystal */ + at91_clock_init(3686400); + +#ifdef CONFIG_SERIAL_AT91 + at91_console_port = CSB337_SERIAL_CONSOLE; + memcpy(at91_serial_map, serial, sizeof(serial)); + + /* Register UARTs */ + for (i = 0; i < AT91_NR_UART; i++) { + if (serial[i] >= 0) + at91_register_uart(i, serial[i]); + } +#endif +} + +static struct at91_eth_data __initdata csb337_eth_data = { + .phy_irq_pin = AT91_PIN_PC2, + .is_rmii = 0, +}; + +static struct at91_usbh_data __initdata csb337_usbh_data = { + .ports = 2, +}; + +static struct at91_udc_data __initdata csb337_udc_data = { + // this has no VBUS sensing pin + .pullup_pin = AT91_PIN_PA24, +}; + +static struct at91_cf_data __initdata csb337_cf_data = { + /* + * connector P4 on the CSB 337 mates to + * connector P8 on the CSB 300CF + */ + + /* CSB337 specific */ + .det_pin = AT91_PIN_PC3, + + /* CSB300CF specific */ + .irq_pin = AT91_PIN_PA19, + .vcc_pin = AT91_PIN_PD0, + .rst_pin = AT91_PIN_PD2, +}; + +static struct at91_mmc_data __initdata csb337_mmc_data = { + .det_pin = AT91_PIN_PD5, + .is_b = 0, + .wire4 = 1, + .wp_pin = AT91_PIN_PD6, +}; + +static void __init csb337_board_init(void) +{ + /* Ethernet */ + at91_add_device_eth(&csb337_eth_data); + /* USB Host */ + at91_add_device_usbh(&csb337_usbh_data); + /* USB Device */ + at91_add_device_udc(&csb337_udc_data); + /* Compact Flash */ + at91_set_gpio_input(AT91_PIN_PB22, 1); /* IOIS16 */ + at91_add_device_cf(&csb337_cf_data); + /* MMC */ + at91_add_device_mmc(&csb337_mmc_data); +} + +MACHINE_START(CSB337, "Cogent CSB337") + /* Maintainer: Bill Gatliff */ + .phys_ram = AT91_SDRAM_BASE, + .phys_io = AT91_BASE_SYS, + .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, + .boot_params = AT91_SDRAM_BASE + 0x100, + .timer = &at91rm9200_timer, + .map_io = csb337_map_io, + .init_irq = csb337_init_irq, + .init_machine = csb337_board_init, +MACHINE_END diff --git a/arch/arm/mach-at91rm9200/board-csb637.c b/arch/arm/mach-at91rm9200/board-csb637.c new file mode 100644 index 000000000000..23e4cc21481a --- /dev/null +++ b/arch/arm/mach-at91rm9200/board-csb637.c @@ -0,0 +1,116 @@ +/* + * linux/arch/arm/mach-at91rm9200/board-csb637.c + * + * Copyright (C) 2005 SAN People + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#include +#include +#include +#include +#include +#include + +#include +#include +#include +#include + +#include +#include +#include + +#include +#include +#include + +#include "generic.h" + +static void __init csb637_init_irq(void) +{ + /* Initialize AIC controller */ + at91rm9200_init_irq(NULL); + + /* Set up the GPIO interrupts */ + at91_gpio_irq_setup(BGA_GPIO_BANKS); +} + +/* + * Serial port configuration. + * 0 .. 3 = USART0 .. USART3 + * 4 = DBGU + */ +#define CSB637_UART_MAP { 4, 1, -1, -1, -1 } /* ttyS0, ..., ttyS4 */ +#define CSB637_SERIAL_CONSOLE 0 /* ttyS0 */ + +static void __init csb637_map_io(void) +{ + int serial[AT91_NR_UART] = CSB637_UART_MAP; + int i; + + at91rm9200_map_io(); + + /* Initialize clocks: 3.6864 MHz crystal */ + at91_clock_init(3686400); + +#ifdef CONFIG_SERIAL_AT91 + at91_console_port = CSB637_SERIAL_CONSOLE; + memcpy(at91_serial_map, serial, sizeof(serial)); + + /* Register UARTs */ + for (i = 0; i < AT91_NR_UART; i++) { + if (serial[i] >= 0) + at91_register_uart(i, serial[i]); + } +#endif +} + +static struct at91_eth_data __initdata csb637_eth_data = { + .phy_irq_pin = AT91_PIN_PC0, + .is_rmii = 0, +}; + +static struct at91_usbh_data __initdata csb637_usbh_data = { + .ports = 2, +}; + +static struct at91_udc_data __initdata csb637_udc_data = { + .vbus_pin = AT91_PIN_PB28, + .pullup_pin = AT91_PIN_PB1, +}; + +static void __init csb637_board_init(void) +{ + /* Ethernet */ + at91_add_device_eth(&csb637_eth_data); + /* USB Host */ + at91_add_device_usbh(&csb637_usbh_data); + /* USB Device */ + at91_add_device_udc(&csb637_udc_data); +} + +MACHINE_START(CSB637, "Cogent CSB637") + /* Maintainer: Bill Gatliff */ + .phys_ram = AT91_SDRAM_BASE, + .phys_io = AT91_BASE_SYS, + .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, + .boot_params = AT91_SDRAM_BASE + 0x100, + .timer = &at91rm9200_timer, + .map_io = csb637_map_io, + .init_irq = csb637_init_irq, + .init_machine = csb637_board_init, +MACHINE_END diff --git a/arch/arm/mach-at91rm9200/board-dk.c b/arch/arm/mach-at91rm9200/board-dk.c new file mode 100644 index 000000000000..8c747a31b95a --- /dev/null +++ b/arch/arm/mach-at91rm9200/board-dk.c @@ -0,0 +1,138 @@ +/* + * linux/arch/arm/mach-at91rm9200/board-dk.c + * + * Copyright (C) 2005 SAN People + * + * Epson S1D framebuffer glue code is: + * Copyright (C) 2005 Thibaut VARENE + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#include +#include +#include +#include +#include +#include + +#include +#include +#include +#include + +#include +#include +#include + +#include +#include +#include + +#include "generic.h" + +static void __init dk_init_irq(void) +{ + /* Initialize AIC controller */ + at91rm9200_init_irq(NULL); + + /* Set up the GPIO interrupts */ + at91_gpio_irq_setup(BGA_GPIO_BANKS); +} + +/* + * Serial port configuration. + * 0 .. 3 = USART0 .. USART3 + * 4 = DBGU + */ +#define DK_UART_MAP { 4, 1, -1, -1, -1 } /* ttyS0, ..., ttyS4 */ +#define DK_SERIAL_CONSOLE 0 /* ttyS0 */ + +static void __init dk_map_io(void) +{ + int serial[AT91_NR_UART] = DK_UART_MAP; + int i; + + at91rm9200_map_io(); + + /* Initialize clocks: 18.432 MHz crystal */ + at91_clock_init(18432000); + +#ifdef CONFIG_SERIAL_AT91 + at91_console_port = DK_SERIAL_CONSOLE; + memcpy(at91_serial_map, serial, sizeof(serial)); + + /* Register UARTs */ + for (i = 0; i < AT91_NR_UART; i++) { + if (at91_serial_map[i] >= 0) + at91_register_uart(i, at91_serial_map[i]); + } +#endif +} + +static struct at91_eth_data __initdata dk_eth_data = { + .phy_irq_pin = AT91_PIN_PC4, + .is_rmii = 1, +}; + +static struct at91_usbh_data __initdata dk_usbh_data = { + .ports = 2, +}; + +static struct at91_udc_data __initdata dk_udc_data = { + .vbus_pin = AT91_PIN_PD4, + .pullup_pin = AT91_PIN_PD5, +}; + +static struct at91_cf_data __initdata dk_cf_data = { + .det_pin = AT91_PIN_PB0, + .rst_pin = AT91_PIN_PC5, + // .irq_pin = ... not connected + // .vcc_pin = ... always powered +}; + +static struct at91_mmc_data __initdata dk_mmc_data = { + .is_b = 0, + .wire4 = 1, +}; + +static void __init dk_board_init(void) +{ + /* Ethernet */ + at91_add_device_eth(&dk_eth_data); + /* USB Host */ + at91_add_device_usbh(&dk_usbh_data); + /* USB Device */ + at91_add_device_udc(&dk_udc_data); + /* Compact Flash */ + at91_add_device_cf(&dk_cf_data); + /* MMC */ + at91_set_gpio_output(AT91_PIN_PB7, 1); /* this MMC card slot can optionally use SPI signaling (CS3). default: MMC */ + at91_add_device_mmc(&dk_mmc_data); + /* VGA */ +// dk_add_device_video(); +} + +MACHINE_START(AT91RM9200DK, "Atmel AT91RM9200-DK") + /* Maintainer: SAN People/Atmel */ + .phys_ram = AT91_SDRAM_BASE, + .phys_io = AT91_BASE_SYS, + .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, + .boot_params = AT91_SDRAM_BASE + 0x100, + .timer = &at91rm9200_timer, + .map_io = dk_map_io, + .init_irq = dk_init_irq, + .init_machine = dk_board_init, +MACHINE_END diff --git a/arch/arm/mach-at91rm9200/board-ek.c b/arch/arm/mach-at91rm9200/board-ek.c new file mode 100644 index 000000000000..d140645711be --- /dev/null +++ b/arch/arm/mach-at91rm9200/board-ek.c @@ -0,0 +1,131 @@ +/* + * linux/arch/arm/mach-at91rm9200/board-ek.c + * + * Copyright (C) 2005 SAN People + * + * Epson S1D framebuffer glue code is: + * Copyright (C) 2005 Thibaut VARENE + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#include +#include +#include +#include +#include +#include + +#include +#include +#include +#include + +#include +#include +#include + +#include +#include +#include + +#include "generic.h" + +static void __init ek_init_irq(void) +{ + /* Initialize AIC controller */ + at91rm9200_init_irq(NULL); + + /* Set up the GPIO interrupts */ + at91_gpio_irq_setup(BGA_GPIO_BANKS); +} + +/* + * Serial port configuration. + * 0 .. 3 = USART0 .. USART3 + * 4 = DBGU + */ +#define EK_UART_MAP { 4, 1, -1, -1, -1 } /* ttyS0, ..., ttyS4 */ +#define EK_SERIAL_CONSOLE 0 /* ttyS0 */ + +static void __init ek_map_io(void) +{ + int serial[AT91_NR_UART] = EK_UART_MAP; + int i; + + at91rm9200_map_io(); + + /* Initialize clocks: 18.432 MHz crystal */ + at91_clock_init(18432000); + +#ifdef CONFIG_SERIAL_AT91 + at91_console_port = EK_SERIAL_CONSOLE; + memcpy(at91_serial_map, serial, sizeof(serial)); + + /* Register UARTs */ + for (i = 0; i < AT91_NR_UART; i++) { + if (serial[i] >= 0) + at91_register_uart(i, serial[i]); + } +#endif +} + +static struct at91_eth_data __initdata ek_eth_data = { + .phy_irq_pin = AT91_PIN_PC4, + .is_rmii = 1, +}; + +static struct at91_usbh_data __initdata ek_usbh_data = { + .ports = 2, +}; + +static struct at91_udc_data __initdata ek_udc_data = { + .vbus_pin = AT91_PIN_PD4, + .pullup_pin = AT91_PIN_PD5, +}; + +static struct at91_mmc_data __initdata ek_mmc_data = { + .det_pin = AT91_PIN_PB27, + .is_b = 0, + .wire4 = 1, + .wp_pin = AT91_PIN_PA17, +}; + +static void __init ek_board_init(void) +{ + /* Ethernet */ + at91_add_device_eth(&ek_eth_data); + /* USB Host */ + at91_add_device_usbh(&ek_usbh_data); + /* USB Device */ + at91_add_device_udc(&ek_udc_data); + /* MMC */ + at91_set_gpio_output(AT91_PIN_PB22, 1); /* this MMC card slot can optionally use SPI signaling (CS3). default: MMC */ + at91_add_device_mmc(&ek_mmc_data); + /* VGA */ +// ek_add_device_video(); +} + +MACHINE_START(AT91RM9200EK, "Atmel AT91RM9200-EK") + /* Maintainer: SAN People/Atmel */ + .phys_ram = AT91_SDRAM_BASE, + .phys_io = AT91_BASE_SYS, + .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, + .boot_params = AT91_SDRAM_BASE + 0x100, + .timer = &at91rm9200_timer, + .map_io = ek_map_io, + .init_irq = ek_init_irq, + .init_machine = ek_board_init, +MACHINE_END diff --git a/arch/arm/mach-integrator/clock.c b/arch/arm/mach-integrator/clock.c index 40684e01e865..95a1e263f7fa 100644 --- a/arch/arm/mach-integrator/clock.c +++ b/arch/arm/mach-integrator/clock.c @@ -15,6 +15,7 @@ #include #include #include +#include #include #include @@ -22,20 +23,20 @@ #include "clock.h" static LIST_HEAD(clocks); -static DECLARE_MUTEX(clocks_sem); +static DEFINE_MUTEX(clocks_mutex); struct clk *clk_get(struct device *dev, const char *id) { struct clk *p, *clk = ERR_PTR(-ENOENT); - down(&clocks_sem); + mutex_lock(&clocks_mutex); list_for_each_entry(p, &clocks, node) { if (strcmp(id, p->name) == 0 && try_module_get(p->owner)) { clk = p; break; } } - up(&clocks_sem); + mutex_unlock(&clocks_mutex); return clk; } @@ -107,18 +108,18 @@ static struct clk uart_clk = { int clk_register(struct clk *clk) { - down(&clocks_sem); + mutex_lock(&clocks_mutex); list_add(&clk->node, &clocks); - up(&clocks_sem); + mutex_unlock(&clocks_mutex); return 0; } EXPORT_SYMBOL(clk_register); void clk_unregister(struct clk *clk) { - down(&clocks_sem); + mutex_lock(&clocks_mutex); list_del(&clk->node); - up(&clocks_sem); + mutex_unlock(&clocks_mutex); } EXPORT_SYMBOL(clk_unregister); diff --git a/arch/arm/mach-pxa/ssp.c b/arch/arm/mach-pxa/ssp.c index a68b30eff4d2..93096befd017 100644 --- a/arch/arm/mach-pxa/ssp.c +++ b/arch/arm/mach-pxa/ssp.c @@ -31,6 +31,7 @@ #include #include #include +#include #include #include #include @@ -59,7 +60,7 @@ static const struct ssp_info_ ssp_info[PXA_SSP_PORTS] = { #endif }; -static DECLARE_MUTEX(sem); +static DEFINE_MUTEX(mutex); static int use_count[PXA_SSP_PORTS] = {0, 0, 0}; static irqreturn_t ssp_interrupt(int irq, void *dev_id, struct pt_regs *regs) @@ -239,16 +240,16 @@ int ssp_init(struct ssp_dev *dev, u32 port, u32 init_flags) if (port > PXA_SSP_PORTS || port == 0) return -ENODEV; - down(&sem); + mutex_lock(&mutex); if (use_count[port - 1]) { - up(&sem); + mutex_unlock(&mutex); return -EBUSY; } use_count[port - 1]++; if (!request_mem_region(__PREG(SSCR0_P(port)), 0x2c, "SSP")) { use_count[port - 1]--; - up(&sem); + mutex_unlock(&mutex); return -EBUSY; } dev->port = port; @@ -265,13 +266,13 @@ int ssp_init(struct ssp_dev *dev, u32 port, u32 init_flags) /* turn on SSP port clock */ pxa_set_cken(ssp_info[port-1].clock, 1); - up(&sem); + mutex_unlock(&mutex); return 0; out_region: release_mem_region(__PREG(SSCR0_P(port)), 0x2c); use_count[port - 1]--; - up(&sem); + mutex_unlock(&mutex); return ret; } @@ -282,7 +283,7 @@ out_region: */ void ssp_exit(struct ssp_dev *dev) { - down(&sem); + mutex_lock(&mutex); SSCR0_P(dev->port) &= ~SSCR0_SSE; if (dev->port > PXA_SSP_PORTS || dev->port == 0) { @@ -295,7 +296,7 @@ void ssp_exit(struct ssp_dev *dev) free_irq(dev->irq, dev); release_mem_region(__PREG(SSCR0_P(dev->port)), 0x2c); use_count[dev->port - 1]--; - up(&sem); + mutex_unlock(&mutex); } EXPORT_SYMBOL(ssp_write_word); diff --git a/arch/arm/mach-realview/clock.c b/arch/arm/mach-realview/clock.c index ec3f7e798623..21325a4da9da 100644 --- a/arch/arm/mach-realview/clock.c +++ b/arch/arm/mach-realview/clock.c @@ -14,6 +14,7 @@ #include #include #include +#include #include #include @@ -21,20 +22,20 @@ #include "clock.h" static LIST_HEAD(clocks); -static DECLARE_MUTEX(clocks_sem); +static DEFINE_MUTEX(clocks_mutex); struct clk *clk_get(struct device *dev, const char *id) { struct clk *p, *clk = ERR_PTR(-ENOENT); - down(&clocks_sem); + mutex_lock(&clocks_mutex); list_for_each_entry(p, &clocks, node) { if (strcmp(id, p->name) == 0 && try_module_get(p->owner)) { clk = p; break; } } - up(&clocks_sem); + mutex_unlock(&clocks_mutex); return clk; } @@ -109,18 +110,18 @@ static struct clk mmci_clk = { int clk_register(struct clk *clk) { - down(&clocks_sem); + mutex_lock(&clocks_mutex); list_add(&clk->node, &clocks); - up(&clocks_sem); + mutex_unlock(&clocks_mutex); return 0; } EXPORT_SYMBOL(clk_register); void clk_unregister(struct clk *clk) { - down(&clocks_sem); + mutex_lock(&clocks_mutex); list_del(&clk->node); - up(&clocks_sem); + mutex_unlock(&clocks_mutex); } EXPORT_SYMBOL(clk_unregister); diff --git a/arch/arm/mach-s3c2410/clock.c b/arch/arm/mach-s3c2410/clock.c index fc09ba92d66a..af2f3d52b61b 100644 --- a/arch/arm/mach-s3c2410/clock.c +++ b/arch/arm/mach-s3c2410/clock.c @@ -37,6 +37,7 @@ #include #include #include +#include #include #include @@ -51,7 +52,7 @@ /* clock information */ static LIST_HEAD(clocks); -static DECLARE_MUTEX(clocks_sem); +static DEFINE_MUTEX(clocks_mutex); /* old functions */ @@ -102,7 +103,7 @@ struct clk *clk_get(struct device *dev, const char *id) else idno = to_platform_device(dev)->id; - down(&clocks_sem); + mutex_lock(&clocks_mutex); list_for_each_entry(p, &clocks, list) { if (p->id == idno && @@ -126,7 +127,7 @@ struct clk *clk_get(struct device *dev, const char *id) } } - up(&clocks_sem); + mutex_unlock(&clocks_mutex); return clk; } @@ -362,9 +363,9 @@ int s3c24xx_register_clock(struct clk *clk) /* add to the list of available clocks */ - down(&clocks_sem); + mutex_lock(&clocks_mutex); list_add(&clk->list, &clocks); - up(&clocks_sem); + mutex_unlock(&clocks_mutex); return 0; } diff --git a/arch/arm/mach-versatile/clock.c b/arch/arm/mach-versatile/clock.c index dcf10014f5cd..9858c96560e2 100644 --- a/arch/arm/mach-versatile/clock.c +++ b/arch/arm/mach-versatile/clock.c @@ -15,6 +15,7 @@ #include #include #include +#include #include #include @@ -22,20 +23,20 @@ #include "clock.h" static LIST_HEAD(clocks); -static DECLARE_MUTEX(clocks_sem); +static DEFINE_MUTEX(clocks_mutex); struct clk *clk_get(struct device *dev, const char *id) { struct clk *p, *clk = ERR_PTR(-ENOENT); - down(&clocks_sem); + mutex_lock(&clocks_mutex); list_for_each_entry(p, &clocks, node) { if (strcmp(id, p->name) == 0 && try_module_get(p->owner)) { clk = p; break; } } - up(&clocks_sem); + mutex_unlock(&clocks_mutex); return clk; } @@ -110,18 +111,18 @@ static struct clk mmci_clk = { int clk_register(struct clk *clk) { - down(&clocks_sem); + mutex_lock(&clocks_mutex); list_add(&clk->node, &clocks); - up(&clocks_sem); + mutex_unlock(&clocks_mutex); return 0; } EXPORT_SYMBOL(clk_register); void clk_unregister(struct clk *clk) { - down(&clocks_sem); + mutex_lock(&clocks_mutex); list_del(&clk->node); - up(&clocks_sem); + mutex_unlock(&clocks_mutex); } EXPORT_SYMBOL(clk_unregister); diff --git a/arch/arm/mm/consistent.c b/arch/arm/mm/consistent.c index 0513ed1b2fcf..c2ee18d2075e 100644 --- a/arch/arm/mm/consistent.c +++ b/arch/arm/mm/consistent.c @@ -20,15 +20,25 @@ #include #include +#include + +/* Sanity check size */ +#if (CONSISTENT_DMA_SIZE % SZ_2M) +#error "CONSISTENT_DMA_SIZE must be multiple of 2MiB" +#endif -#define CONSISTENT_BASE (0xffc00000) #define CONSISTENT_END (0xffe00000) +#define CONSISTENT_BASE (CONSISTENT_END - CONSISTENT_DMA_SIZE) + #define CONSISTENT_OFFSET(x) (((unsigned long)(x) - CONSISTENT_BASE) >> PAGE_SHIFT) +#define CONSISTENT_PTE_INDEX(x) (((unsigned long)(x) - CONSISTENT_BASE) >> PGDIR_SHIFT) +#define NUM_CONSISTENT_PTES (CONSISTENT_DMA_SIZE >> PGDIR_SHIFT) + /* - * This is the page table (2MB) covering uncached, DMA consistent allocations + * These are the page tables (2MB each) covering uncached, DMA consistent allocations */ -static pte_t *consistent_pte; +static pte_t *consistent_pte[NUM_CONSISTENT_PTES]; static DEFINE_SPINLOCK(consistent_lock); /* @@ -142,7 +152,7 @@ __dma_alloc(struct device *dev, size_t size, dma_addr_t *handle, gfp_t gfp, unsigned long order; u64 mask = ISA_DMA_THRESHOLD, limit; - if (!consistent_pte) { + if (!consistent_pte[0]) { printk(KERN_ERR "%s: not initialised\n", __func__); dump_stack(); return NULL; @@ -205,9 +215,12 @@ __dma_alloc(struct device *dev, size_t size, dma_addr_t *handle, gfp_t gfp, c = vm_region_alloc(&consistent_head, size, gfp & ~(__GFP_DMA | __GFP_HIGHMEM)); if (c) { - pte_t *pte = consistent_pte + CONSISTENT_OFFSET(c->vm_start); + pte_t *pte; struct page *end = page + (1 << order); + int idx = CONSISTENT_PTE_INDEX(c->vm_start); + u32 off = CONSISTENT_OFFSET(c->vm_start) & (PTRS_PER_PTE-1); + pte = consistent_pte[idx] + off; c->vm_pages = page; /* @@ -226,6 +239,11 @@ __dma_alloc(struct device *dev, size_t size, dma_addr_t *handle, gfp_t gfp, set_pte(pte, mk_pte(page, prot)); page++; pte++; + off++; + if (off >= PTRS_PER_PTE) { + off = 0; + pte = consistent_pte[++idx]; + } } while (size -= PAGE_SIZE); /* @@ -327,6 +345,8 @@ void dma_free_coherent(struct device *dev, size_t size, void *cpu_addr, dma_addr struct vm_region *c; unsigned long flags, addr; pte_t *ptep; + int idx; + u32 off; WARN_ON(irqs_disabled()); @@ -347,7 +367,9 @@ void dma_free_coherent(struct device *dev, size_t size, void *cpu_addr, dma_addr size = c->vm_end - c->vm_start; } - ptep = consistent_pte + CONSISTENT_OFFSET(c->vm_start); + idx = CONSISTENT_PTE_INDEX(c->vm_start); + off = CONSISTENT_OFFSET(c->vm_start) & (PTRS_PER_PTE-1); + ptep = consistent_pte[idx] + off; addr = c->vm_start; do { pte_t pte = ptep_get_and_clear(&init_mm, addr, ptep); @@ -355,6 +377,11 @@ void dma_free_coherent(struct device *dev, size_t size, void *cpu_addr, dma_addr ptep++; addr += PAGE_SIZE; + off++; + if (off >= PTRS_PER_PTE) { + off = 0; + ptep = consistent_pte[++idx]; + } if (!pte_none(pte) && pte_present(pte)) { pfn = pte_pfn(pte); @@ -401,11 +428,12 @@ static int __init consistent_init(void) pgd_t *pgd; pmd_t *pmd; pte_t *pte; - int ret = 0; + int ret = 0, i = 0; + u32 base = CONSISTENT_BASE; do { - pgd = pgd_offset(&init_mm, CONSISTENT_BASE); - pmd = pmd_alloc(&init_mm, pgd, CONSISTENT_BASE); + pgd = pgd_offset(&init_mm, base); + pmd = pmd_alloc(&init_mm, pgd, base); if (!pmd) { printk(KERN_ERR "%s: no pmd tables\n", __func__); ret = -ENOMEM; @@ -413,15 +441,16 @@ static int __init consistent_init(void) } WARN_ON(!pmd_none(*pmd)); - pte = pte_alloc_kernel(pmd, CONSISTENT_BASE); + pte = pte_alloc_kernel(pmd, base); if (!pte) { printk(KERN_ERR "%s: no pte tables\n", __func__); ret = -ENOMEM; break; } - consistent_pte = pte; - } while (0); + consistent_pte[i++] = pte; + base += (1 << PGDIR_SHIFT); + } while (base < CONSISTENT_END); return ret; } diff --git a/arch/arm/plat-omap/clock.c b/arch/arm/plat-omap/clock.c index 84fd65656fcf..7ebc5a29db8d 100644 --- a/arch/arm/plat-omap/clock.c +++ b/arch/arm/plat-omap/clock.c @@ -20,6 +20,7 @@ #include #include #include +#include #include #include @@ -27,7 +28,7 @@ #include LIST_HEAD(clocks); -static DECLARE_MUTEX(clocks_sem); +static DEFINE_MUTEX(clocks_mutex); DEFINE_SPINLOCK(clockfw_lock); static struct clk_functions *arch_clock; @@ -40,14 +41,14 @@ struct clk * clk_get(struct device *dev, const char *id) { struct clk *p, *clk = ERR_PTR(-ENOENT); - down(&clocks_sem); + mutex_lock(&clocks_mutex); list_for_each_entry(p, &clocks, node) { if (strcmp(id, p->name) == 0 && try_module_get(p->owner)) { clk = p; break; } } - up(&clocks_sem); + mutex_unlock(&clocks_mutex); return clk; } @@ -249,11 +250,11 @@ void propagate_rate(struct clk * tclk) int clk_register(struct clk *clk) { - down(&clocks_sem); + mutex_lock(&clocks_mutex); list_add(&clk->node, &clocks); if (clk->init) clk->init(clk); - up(&clocks_sem); + mutex_unlock(&clocks_mutex); return 0; } @@ -261,9 +262,9 @@ EXPORT_SYMBOL(clk_register); void clk_unregister(struct clk *clk) { - down(&clocks_sem); + mutex_lock(&clocks_mutex); list_del(&clk->node); - up(&clocks_sem); + mutex_unlock(&clocks_mutex); } EXPORT_SYMBOL(clk_unregister); diff --git a/drivers/i2c/busses/i2c-pxa.c b/drivers/i2c/busses/i2c-pxa.c index 70f7ab829d36..86e2234faf80 100644 --- a/drivers/i2c/busses/i2c-pxa.c +++ b/drivers/i2c/busses/i2c-pxa.c @@ -899,6 +899,12 @@ static int i2c_pxa_xfer(struct i2c_adapter *adap, struct i2c_msg msgs[], int num struct pxa_i2c *i2c = adap->algo_data; int ret, i; + /* If the I2C controller is disabled we need to reset it (probably due + to a suspend/resume destroying state). We do this here as we can then + avoid worrying about resuming the controller before its users. */ + if (!(ICR & ICR_IUE)) + i2c_pxa_reset(i2c); + for (i = adap->retries; i >= 0; i--) { ret = i2c_pxa_do_xfer(i2c, msgs, num); if (ret != I2C_RETRY) @@ -939,7 +945,9 @@ static struct pxa_i2c i2c_pxa = { static int i2c_pxa_probe(struct platform_device *dev) { struct pxa_i2c *i2c = &i2c_pxa; +#ifdef CONFIG_I2C_PXA_SLAVE struct i2c_pxa_platform_data *plat = dev->dev.platform_data; +#endif int ret; #ifdef CONFIG_PXA27x @@ -1024,5 +1032,7 @@ static void i2c_adap_pxa_exit(void) return platform_driver_unregister(&i2c_pxa_driver); } +MODULE_LICENSE("GPL"); + module_init(i2c_adap_pxa_init); module_exit(i2c_adap_pxa_exit); diff --git a/drivers/pcmcia/pxa2xx_mainstone.c b/drivers/pcmcia/pxa2xx_mainstone.c index 5d957dfe23d9..fda06941e730 100644 --- a/drivers/pcmcia/pxa2xx_mainstone.c +++ b/drivers/pcmcia/pxa2xx_mainstone.c @@ -171,27 +171,22 @@ static int __init mst_pcmcia_init(void) { int ret; - mst_pcmcia_device = kzalloc(sizeof(*mst_pcmcia_device), GFP_KERNEL); + mst_pcmcia_device = platform_device_alloc("pxa2xx-pcmcia", -1); if (!mst_pcmcia_device) return -ENOMEM; - mst_pcmcia_device->name = "pxa2xx-pcmcia"; + mst_pcmcia_device->dev.platform_data = &mst_pcmcia_ops; - ret = platform_device_register(mst_pcmcia_device); + ret = platform_device_add(mst_pcmcia_device); + if (ret) - kfree(mst_pcmcia_device); + platform_device_put(mst_pcmcia_device); return ret; } static void __exit mst_pcmcia_exit(void) { - /* - * This call is supposed to free our mst_pcmcia_device. - * Unfortunately platform_device don't have a free method, and - * we can't assume it's free of any reference at this point so we - * can't free it either. - */ platform_device_unregister(mst_pcmcia_device); } diff --git a/drivers/pcmcia/pxa2xx_sharpsl.c b/drivers/pcmcia/pxa2xx_sharpsl.c index 12a7244a5ec8..fd3647368955 100644 --- a/drivers/pcmcia/pxa2xx_sharpsl.c +++ b/drivers/pcmcia/pxa2xx_sharpsl.c @@ -263,30 +263,25 @@ static int __init sharpsl_pcmcia_init(void) { int ret; - sharpsl_pcmcia_ops.nr=platform_scoop_config->num_devs; - sharpsl_pcmcia_device = kzalloc(sizeof(*sharpsl_pcmcia_device), GFP_KERNEL); + sharpsl_pcmcia_ops.nr = platform_scoop_config->num_devs; + sharpsl_pcmcia_device = platform_device_alloc("pxa2xx-pcmcia", -1); + if (!sharpsl_pcmcia_device) return -ENOMEM; - sharpsl_pcmcia_device->name = "pxa2xx-pcmcia"; sharpsl_pcmcia_device->dev.platform_data = &sharpsl_pcmcia_ops; - sharpsl_pcmcia_device->dev.parent=platform_scoop_config->devs[0].dev; + sharpsl_pcmcia_device->dev.parent = platform_scoop_config->devs[0].dev; + + ret = platform_device_add(sharpsl_pcmcia_device); - ret = platform_device_register(sharpsl_pcmcia_device); if (ret) - kfree(sharpsl_pcmcia_device); + platform_device_put(sharpsl_pcmcia_device); return ret; } static void __exit sharpsl_pcmcia_exit(void) { - /* - * This call is supposed to free our sharpsl_pcmcia_device. - * Unfortunately platform_device don't have a free method, and - * we can't assume it's free of any reference at this point so we - * can't free it either. - */ platform_device_unregister(sharpsl_pcmcia_device); } diff --git a/drivers/serial/Kconfig b/drivers/serial/Kconfig index 698cb76819d9..843717275d49 100644 --- a/drivers/serial/Kconfig +++ b/drivers/serial/Kconfig @@ -280,6 +280,40 @@ config SERIAL_AMBA_PL011_CONSOLE your boot loader (lilo or loadlin) about how to pass options to the kernel at boot time.) +config SERIAL_AT91 + bool "AT91RM9200 serial port support" + depends on ARM && ARCH_AT91RM9200 + select SERIAL_CORE + help + This enables the driver for the on-chip UARTs of the AT91RM9200 + processor. + +config SERIAL_AT91_CONSOLE + bool "Support for console on AT91RM9200 serial port" + depends on SERIAL_AT91=y + select SERIAL_CORE_CONSOLE + help + Say Y here if you wish to use a UART on the AT91RM9200 as the system + console (the system console is the device which receives all kernel + messages and warnings and which allows logins in single user mode). + +config SERIAL_AT91_TTYAT + bool "Install as device ttyAT0-4 instead of ttyS0-4" + depends on SERIAL_AT91=y + help + Say Y here if you wish to have the five internal AT91RM9200 UARTs + appear as /dev/ttyAT0-4 (major 240, minor 0-4) instead of the + normal /dev/ttyS0-4 (major 4, minor 64-68). This is necessary if + you also want other UARTs, such as external 8250/16C550 compatible + UARTs. + The ttySn nodes are legally reserved for the 8250 serial driver + but are often misused by other serial drivers. + + To use this, you should create suitable ttyATn device nodes in + /dev/, and pass "console=ttyATn" to the kernel. + + Say Y if you have an external 8250/16C550 UART. If unsure, say N. + config SERIAL_CLPS711X tristate "CLPS711X serial port support" depends on ARM && ARCH_CLPS711X diff --git a/drivers/serial/Makefile b/drivers/serial/Makefile index 137148bba4fa..24a583e482bb 100644 --- a/drivers/serial/Makefile +++ b/drivers/serial/Makefile @@ -56,3 +56,4 @@ obj-$(CONFIG_SERIAL_JSM) += jsm/ obj-$(CONFIG_SERIAL_TXX9) += serial_txx9.o obj-$(CONFIG_SERIAL_VR41XX) += vr41xx_siu.o obj-$(CONFIG_SERIAL_SGI_IOC4) += ioc4_serial.o +obj-$(CONFIG_SERIAL_AT91) += at91_serial.o diff --git a/drivers/serial/at91_serial.c b/drivers/serial/at91_serial.c new file mode 100644 index 000000000000..0e206063d685 --- /dev/null +++ b/drivers/serial/at91_serial.c @@ -0,0 +1,894 @@ +/* + * linux/drivers/char/at91_serial.c + * + * Driver for Atmel AT91RM9200 Serial ports + * + * Copyright (C) 2003 Rick Bronson + * + * Based on drivers/char/serial_sa1100.c, by Deep Blue Solutions Ltd. + * Based on drivers/char/serial.c, by Linus Torvalds, Theodore Ts'o. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + * + */ +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include + +#include +#include +#include +#include + + +#if defined(CONFIG_SERIAL_AT91_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ) +#define SUPPORT_SYSRQ +#endif + +#include + +#ifdef CONFIG_SERIAL_AT91_TTYAT + +/* Use device name ttyAT, major 204 and minor 154-169. This is necessary if we + * should coexist with the 8250 driver, such as if we have an external 16C550 + * UART. */ +#define SERIAL_AT91_MAJOR 204 +#define MINOR_START 154 +#define AT91_DEVICENAME "ttyAT" + +#else + +/* Use device name ttyS, major 4, minor 64-68. This is the usual serial port + * name, but it is legally reserved for the 8250 driver. */ +#define SERIAL_AT91_MAJOR TTY_MAJOR +#define MINOR_START 64 +#define AT91_DEVICENAME "ttyS" + +#endif + +#define AT91_VA_BASE_DBGU ((unsigned long) AT91_VA_BASE_SYS + AT91_DBGU) +#define AT91_ISR_PASS_LIMIT 256 + +#define UART_PUT_CR(port,v) writel(v, (port)->membase + AT91_US_CR) +#define UART_GET_MR(port) readl((port)->membase + AT91_US_MR) +#define UART_PUT_MR(port,v) writel(v, (port)->membase + AT91_US_MR) +#define UART_PUT_IER(port,v) writel(v, (port)->membase + AT91_US_IER) +#define UART_PUT_IDR(port,v) writel(v, (port)->membase + AT91_US_IDR) +#define UART_GET_IMR(port) readl((port)->membase + AT91_US_IMR) +#define UART_GET_CSR(port) readl((port)->membase + AT91_US_CSR) +#define UART_GET_CHAR(port) readl((port)->membase + AT91_US_RHR) +#define UART_PUT_CHAR(port,v) writel(v, (port)->membase + AT91_US_THR) +#define UART_GET_BRGR(port) readl((port)->membase + AT91_US_BRGR) +#define UART_PUT_BRGR(port,v) writel(v, (port)->membase + AT91_US_BRGR) +#define UART_PUT_RTOR(port,v) writel(v, (port)->membase + AT91_US_RTOR) + +// #define UART_GET_CR(port) readl((port)->membase + AT91_US_CR) // is write-only + + /* PDC registers */ +#define UART_PUT_PTCR(port,v) writel(v, (port)->membase + AT91_PDC_PTCR) +#define UART_PUT_RPR(port,v) writel(v, (port)->membase + AT91_PDC_RPR) +#define UART_PUT_RCR(port,v) writel(v, (port)->membase + AT91_PDC_RCR) +#define UART_GET_RCR(port) readl((port)->membase + AT91_PDC_RCR) +#define UART_PUT_RNPR(port,v) writel(v, (port)->membase + AT91_PDC_RNPR) +#define UART_PUT_RNCR(port,v) writel(v, (port)->membase + AT91_PDC_RNCR) + + +static int (*at91_open)(struct uart_port *); +static void (*at91_close)(struct uart_port *); + +#ifdef SUPPORT_SYSRQ +static struct console at91_console; +#endif + +/* + * Return TIOCSER_TEMT when transmitter FIFO and Shift register is empty. + */ +static u_int at91_tx_empty(struct uart_port *port) +{ + return (UART_GET_CSR(port) & AT91_US_TXEMPTY) ? TIOCSER_TEMT : 0; +} + +/* + * Set state of the modem control output lines + */ +static void at91_set_mctrl(struct uart_port *port, u_int mctrl) +{ + unsigned int control = 0; + + /* + * Errata #39: RTS0 is not internally connected to PA21. We need to drive + * the pin manually. + */ + if (port->mapbase == AT91_VA_BASE_US0) { + if (mctrl & TIOCM_RTS) + at91_sys_write(AT91_PIOA + PIO_CODR, AT91_PA21_RTS0); + else + at91_sys_write(AT91_PIOA + PIO_SODR, AT91_PA21_RTS0); + } + + if (mctrl & TIOCM_RTS) + control |= AT91_US_RTSEN; + else + control |= AT91_US_RTSDIS; + + if (mctrl & TIOCM_DTR) + control |= AT91_US_DTREN; + else + control |= AT91_US_DTRDIS; + + UART_PUT_CR(port,control); +} + +/* + * Get state of the modem control input lines + */ +static u_int at91_get_mctrl(struct uart_port *port) +{ + unsigned int status, ret = 0; + + status = UART_GET_CSR(port); + + /* + * The control signals are active low. + */ + if (!(status & AT91_US_DCD)) + ret |= TIOCM_CD; + if (!(status & AT91_US_CTS)) + ret |= TIOCM_CTS; + if (!(status & AT91_US_DSR)) + ret |= TIOCM_DSR; + if (!(status & AT91_US_RI)) + ret |= TIOCM_RI; + + return ret; +} + +/* + * Stop transmitting. + */ +static void at91_stop_tx(struct uart_port *port) +{ + UART_PUT_IDR(port, AT91_US_TXRDY); + port->read_status_mask &= ~AT91_US_TXRDY; +} + +/* + * Start transmitting. + */ +static void at91_start_tx(struct uart_port *port) +{ + port->read_status_mask |= AT91_US_TXRDY; + UART_PUT_IER(port, AT91_US_TXRDY); +} + +/* + * Stop receiving - port is in process of being closed. + */ +static void at91_stop_rx(struct uart_port *port) +{ + UART_PUT_IDR(port, AT91_US_RXRDY); +} + +/* + * Enable modem status interrupts + */ +static void at91_enable_ms(struct uart_port *port) +{ + port->read_status_mask |= (AT91_US_RIIC | AT91_US_DSRIC | AT91_US_DCDIC | AT91_US_CTSIC); + UART_PUT_IER(port, AT91_US_RIIC | AT91_US_DSRIC | AT91_US_DCDIC | AT91_US_CTSIC); +} + +/* + * Control the transmission of a break signal + */ +static void at91_break_ctl(struct uart_port *port, int break_state) +{ + if (break_state != 0) + UART_PUT_CR(port, AT91_US_STTBRK); /* start break */ + else + UART_PUT_CR(port, AT91_US_STPBRK); /* stop break */ +} + +/* + * Characters received (called from interrupt handler) + */ +static void at91_rx_chars(struct uart_port *port, struct pt_regs *regs) +{ + struct tty_struct *tty = port->info->tty; + unsigned int status, ch, flg; + + status = UART_GET_CSR(port) & port->read_status_mask; + while (status & (AT91_US_RXRDY)) { + ch = UART_GET_CHAR(port); + + if (tty->flip.count >= TTY_FLIPBUF_SIZE) + goto ignore_char; + port->icount.rx++; + + flg = TTY_NORMAL; + + /* + * note that the error handling code is + * out of the main execution path + */ + if (unlikely(status & (AT91_US_PARE | AT91_US_FRAME | AT91_US_OVRE))) { + UART_PUT_CR(port, AT91_US_RSTSTA); /* clear error */ + if (status & (AT91_US_PARE)) + port->icount.parity++; + if (status & (AT91_US_FRAME)) + port->icount.frame++; + if (status & (AT91_US_OVRE)) + port->icount.overrun++; + + if (status & AT91_US_PARE) + flg = TTY_PARITY; + else if (status & AT91_US_FRAME) + flg = TTY_FRAME; + if (status & AT91_US_OVRE) { + /* + * overrun does *not* affect the character + * we read from the FIFO + */ + tty_insert_flip_char(tty, ch, flg); + ch = 0; + flg = TTY_OVERRUN; + } +#ifdef SUPPORT_SYSRQ + port->sysrq = 0; +#endif + } + + if (uart_handle_sysrq_char(port, ch, regs)) + goto ignore_char; + + tty_insert_flip_char(tty, ch, flg); + + ignore_char: + status = UART_GET_CSR(port) & port->read_status_mask; + } + + tty_flip_buffer_push(tty); +} + +/* + * Transmit characters (called from interrupt handler) + */ +static void at91_tx_chars(struct uart_port *port) +{ + struct circ_buf *xmit = &port->info->xmit; + + if (port->x_char) { + UART_PUT_CHAR(port, port->x_char); + port->icount.tx++; + port->x_char = 0; + return; + } + if (uart_circ_empty(xmit) || uart_tx_stopped(port)) { + at91_stop_tx(port); + return; + } + + while (UART_GET_CSR(port) & AT91_US_TXRDY) { + UART_PUT_CHAR(port, xmit->buf[xmit->tail]); + xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); + port->icount.tx++; + if (uart_circ_empty(xmit)) + break; + } + + if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) + uart_write_wakeup(port); + + if (uart_circ_empty(xmit)) + at91_stop_tx(port); +} + +/* + * Interrupt handler + */ +static irqreturn_t at91_interrupt(int irq, void *dev_id, struct pt_regs *regs) +{ + struct uart_port *port = dev_id; + unsigned int status, pending, pass_counter = 0; + + status = UART_GET_CSR(port); + pending = status & port->read_status_mask; + if (pending) { + do { + if (pending & AT91_US_RXRDY) + at91_rx_chars(port, regs); + + /* Clear the relevent break bits */ + if (pending & AT91_US_RXBRK) { + UART_PUT_CR(port, AT91_US_RSTSTA); + port->icount.brk++; + uart_handle_break(port); + } + + // TODO: All reads to CSR will clear these interrupts! + if (pending & AT91_US_RIIC) port->icount.rng++; + if (pending & AT91_US_DSRIC) port->icount.dsr++; + if (pending & AT91_US_DCDIC) + uart_handle_dcd_change(port, !(status & AT91_US_DCD)); + if (pending & AT91_US_CTSIC) + uart_handle_cts_change(port, !(status & AT91_US_CTS)); + if (pending & (AT91_US_RIIC | AT91_US_DSRIC | AT91_US_DCDIC | AT91_US_CTSIC)) + wake_up_interruptible(&port->info->delta_msr_wait); + + if (pending & AT91_US_TXRDY) + at91_tx_chars(port); + if (pass_counter++ > AT91_ISR_PASS_LIMIT) + break; + + status = UART_GET_CSR(port); + pending = status & port->read_status_mask; + } while (pending); + } + return IRQ_HANDLED; +} + +/* + * Perform initialization and enable port for reception + */ +static int at91_startup(struct uart_port *port) +{ + int retval; + + /* + * Ensure that no interrupts are enabled otherwise when + * request_irq() is called we could get stuck trying to + * handle an unexpected interrupt + */ + UART_PUT_IDR(port, -1); + + /* + * Allocate the IRQ + */ + retval = request_irq(port->irq, at91_interrupt, SA_SHIRQ, "at91_serial", port); + if (retval) { + printk("at91_serial: at91_startup - Can't get irq\n"); + return retval; + } + + /* + * If there is a specific "open" function (to register + * control line interrupts) + */ + if (at91_open) { + retval = at91_open(port); + if (retval) { + free_irq(port->irq, port); + return retval; + } + } + + port->read_status_mask = AT91_US_RXRDY | AT91_US_TXRDY | AT91_US_OVRE + | AT91_US_FRAME | AT91_US_PARE | AT91_US_RXBRK; + /* + * Finally, enable the serial port + */ + UART_PUT_CR(port, AT91_US_RSTSTA | AT91_US_RSTRX); + UART_PUT_CR(port, AT91_US_TXEN | AT91_US_RXEN); /* enable xmit & rcvr */ + UART_PUT_IER(port, AT91_US_RXRDY); /* do receive only */ + return 0; +} + +/* + * Disable the port + */ +static void at91_shutdown(struct uart_port *port) +{ + /* + * Disable all interrupts, port and break condition. + */ + UART_PUT_CR(port, AT91_US_RSTSTA); + UART_PUT_IDR(port, -1); + + /* + * Free the interrupt + */ + free_irq(port->irq, port); + + /* + * If there is a specific "close" function (to unregister + * control line interrupts) + */ + if (at91_close) + at91_close(port); +} + +/* + * Power / Clock management. + */ +static void at91_serial_pm(struct uart_port *port, unsigned int state, unsigned int oldstate) +{ + switch (state) { + case 0: + /* + * Enable the peripheral clock for this serial port. + * This is called on uart_open() or a resume event. + */ + at91_sys_write(AT91_PMC_PCER, 1 << port->irq); + break; + case 3: + /* + * Disable the peripheral clock for this serial port. + * This is called on uart_close() or a suspend event. + */ + if (port->irq != AT91_ID_SYS) /* is this a shared clock? */ + at91_sys_write(AT91_PMC_PCDR, 1 << port->irq); + break; + default: + printk(KERN_ERR "at91_serial: unknown pm %d\n", state); + } +} + +/* + * Change the port parameters + */ +static void at91_set_termios(struct uart_port *port, struct termios * termios, struct termios * old) +{ + unsigned long flags; + unsigned int mode, imr, quot, baud; + + baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16); + quot = uart_get_divisor(port, baud); + + /* Get current mode register */ + mode = UART_GET_MR(port) & ~(AT91_US_CHRL | AT91_US_NBSTOP | AT91_US_PAR); + + /* byte size */ + switch (termios->c_cflag & CSIZE) { + case CS5: + mode |= AT91_US_CHRL_5; + break; + case CS6: + mode |= AT91_US_CHRL_6; + break; + case CS7: + mode |= AT91_US_CHRL_7; + break; + default: + mode |= AT91_US_CHRL_8; + break; + } + + /* stop bits */ + if (termios->c_cflag & CSTOPB) + mode |= AT91_US_NBSTOP_2; + + /* parity */ + if (termios->c_cflag & PARENB) { + if (termios->c_cflag & CMSPAR) { /* Mark or Space parity */ + if (termios->c_cflag & PARODD) + mode |= AT91_US_PAR_MARK; + else + mode |= AT91_US_PAR_SPACE; + } + else if (termios->c_cflag & PARODD) + mode |= AT91_US_PAR_ODD; + else + mode |= AT91_US_PAR_EVEN; + } + else + mode |= AT91_US_PAR_NONE; + + spin_lock_irqsave(&port->lock, flags); + + port->read_status_mask |= AT91_US_OVRE; + if (termios->c_iflag & INPCK) + port->read_status_mask |= AT91_US_FRAME | AT91_US_PARE; + if (termios->c_iflag & (BRKINT | PARMRK)) + port->read_status_mask |= AT91_US_RXBRK; + + /* + * Characters to ignore + */ + port->ignore_status_mask = 0; + if (termios->c_iflag & IGNPAR) + port->ignore_status_mask |= (AT91_US_FRAME | AT91_US_PARE); + if (termios->c_iflag & IGNBRK) { + port->ignore_status_mask |= AT91_US_RXBRK; + /* + * If we're ignoring parity and break indicators, + * ignore overruns too (for real raw support). + */ + if (termios->c_iflag & IGNPAR) + port->ignore_status_mask |= AT91_US_OVRE; + } + + // TODO: Ignore all characters if CREAD is set. + + /* update the per-port timeout */ + uart_update_timeout(port, termios->c_cflag, baud); + + /* disable interrupts and drain transmitter */ + imr = UART_GET_IMR(port); /* get interrupt mask */ + UART_PUT_IDR(port, -1); /* disable all interrupts */ + while (!(UART_GET_CSR(port) & AT91_US_TXEMPTY)) { barrier(); } + + /* disable receiver and transmitter */ + UART_PUT_CR(port, AT91_US_TXDIS | AT91_US_RXDIS); + + /* set the parity, stop bits and data size */ + UART_PUT_MR(port, mode); + + /* set the baud rate */ + UART_PUT_BRGR(port, quot); + UART_PUT_CR(port, AT91_US_RSTSTA | AT91_US_RSTRX); + UART_PUT_CR(port, AT91_US_TXEN | AT91_US_RXEN); + + /* restore interrupts */ + UART_PUT_IER(port, imr); + + /* CTS flow-control and modem-status interrupts */ + if (UART_ENABLE_MS(port, termios->c_cflag)) + port->ops->enable_ms(port); + + spin_unlock_irqrestore(&port->lock, flags); +} + +/* + * Return string describing the specified port + */ +static const char *at91_type(struct uart_port *port) +{ + return (port->type == PORT_AT91RM9200) ? "AT91_SERIAL" : NULL; +} + +/* + * Release the memory region(s) being used by 'port'. + */ +static void at91_release_port(struct uart_port *port) +{ + release_mem_region(port->mapbase, + (port->mapbase == AT91_VA_BASE_DBGU) ? 512 : SZ_16K); +} + +/* + * Request the memory region(s) being used by 'port'. + */ +static int at91_request_port(struct uart_port *port) +{ + return request_mem_region(port->mapbase, + (port->mapbase == AT91_VA_BASE_DBGU) ? 512 : SZ_16K, + "at91_serial") != NULL ? 0 : -EBUSY; + +} + +/* + * Configure/autoconfigure the port. + */ +static void at91_config_port(struct uart_port *port, int flags) +{ + if (flags & UART_CONFIG_TYPE) { + port->type = PORT_AT91RM9200; + at91_request_port(port); + } +} + +/* + * Verify the new serial_struct (for TIOCSSERIAL). + */ +static int at91_verify_port(struct uart_port *port, struct serial_struct *ser) +{ + int ret = 0; + if (ser->type != PORT_UNKNOWN && ser->type != PORT_AT91RM9200) + ret = -EINVAL; + if (port->irq != ser->irq) + ret = -EINVAL; + if (ser->io_type != SERIAL_IO_MEM) + ret = -EINVAL; + if (port->uartclk / 16 != ser->baud_base) + ret = -EINVAL; + if ((void *)port->mapbase != ser->iomem_base) + ret = -EINVAL; + if (port->iobase != ser->port) + ret = -EINVAL; + if (ser->hub6 != 0) + ret = -EINVAL; + return ret; +} + +static struct uart_ops at91_pops = { + .tx_empty = at91_tx_empty, + .set_mctrl = at91_set_mctrl, + .get_mctrl = at91_get_mctrl, + .stop_tx = at91_stop_tx, + .start_tx = at91_start_tx, + .stop_rx = at91_stop_rx, + .enable_ms = at91_enable_ms, + .break_ctl = at91_break_ctl, + .startup = at91_startup, + .shutdown = at91_shutdown, + .set_termios = at91_set_termios, + .type = at91_type, + .release_port = at91_release_port, + .request_port = at91_request_port, + .config_port = at91_config_port, + .verify_port = at91_verify_port, + .pm = at91_serial_pm, +}; + +static struct uart_port at91_ports[AT91_NR_UART]; + +void __init at91_init_ports(void) +{ + static int first = 1; + int i; + + if (!first) + return; + first = 0; + + for (i = 0; i < AT91_NR_UART; i++) { + at91_ports[i].iotype = UPIO_MEM; + at91_ports[i].flags = UPF_BOOT_AUTOCONF; + at91_ports[i].uartclk = at91_master_clock; + at91_ports[i].ops = &at91_pops; + at91_ports[i].fifosize = 1; + at91_ports[i].line = i; + } +} + +void __init at91_register_uart_fns(struct at91rm9200_port_fns *fns) +{ + if (fns->enable_ms) + at91_pops.enable_ms = fns->enable_ms; + if (fns->get_mctrl) + at91_pops.get_mctrl = fns->get_mctrl; + if (fns->set_mctrl) + at91_pops.set_mctrl = fns->set_mctrl; + at91_open = fns->open; + at91_close = fns->close; + at91_pops.pm = fns->pm; + at91_pops.set_wake = fns->set_wake; +} + +/* + * Setup ports. + */ +void __init at91_register_uart(int idx, int port) +{ + if ((idx < 0) || (idx >= AT91_NR_UART)) { + printk(KERN_ERR "%s: bad index number %d\n", __FUNCTION__, idx); + return; + } + + switch (port) { + case 0: + at91_ports[idx].membase = (void __iomem *) AT91_VA_BASE_US0; + at91_ports[idx].mapbase = AT91_VA_BASE_US0; + at91_ports[idx].irq = AT91_ID_US0; + AT91_CfgPIO_USART0(); + break; + case 1: + at91_ports[idx].membase = (void __iomem *) AT91_VA_BASE_US1; + at91_ports[idx].mapbase = AT91_VA_BASE_US1; + at91_ports[idx].irq = AT91_ID_US1; + AT91_CfgPIO_USART1(); + break; + case 2: + at91_ports[idx].membase = (void __iomem *) AT91_VA_BASE_US2; + at91_ports[idx].mapbase = AT91_VA_BASE_US2; + at91_ports[idx].irq = AT91_ID_US2; + AT91_CfgPIO_USART2(); + break; + case 3: + at91_ports[idx].membase = (void __iomem *) AT91_VA_BASE_US3; + at91_ports[idx].mapbase = AT91_VA_BASE_US3; + at91_ports[idx].irq = AT91_ID_US3; + AT91_CfgPIO_USART3(); + break; + case 4: + at91_ports[idx].membase = (void __iomem *) AT91_VA_BASE_DBGU; + at91_ports[idx].mapbase = AT91_VA_BASE_DBGU; + at91_ports[idx].irq = AT91_ID_SYS; + AT91_CfgPIO_DBGU(); + break; + default: + printk(KERN_ERR "%s : bad port number %d\n", __FUNCTION__, port); + } +} + +#ifdef CONFIG_SERIAL_AT91_CONSOLE + +/* + * Interrupts are disabled on entering + */ +static void at91_console_write(struct console *co, const char *s, u_int count) +{ + struct uart_port *port = at91_ports + co->index; + unsigned int status, i, imr; + + /* + * First, save IMR and then disable interrupts + */ + imr = UART_GET_IMR(port); /* get interrupt mask */ + UART_PUT_IDR(port, AT91_US_RXRDY | AT91_US_TXRDY); + + /* + * Now, do each character + */ + for (i = 0; i < count; i++) { + do { + status = UART_GET_CSR(port); + } while (!(status & AT91_US_TXRDY)); + UART_PUT_CHAR(port, s[i]); + if (s[i] == '\n') { + do { + status = UART_GET_CSR(port); + } while (!(status & AT91_US_TXRDY)); + UART_PUT_CHAR(port, '\r'); + } + } + + /* + * Finally, wait for transmitter to become empty + * and restore IMR + */ + do { + status = UART_GET_CSR(port); + } while (!(status & AT91_US_TXRDY)); + UART_PUT_IER(port, imr); /* set interrupts back the way they were */ +} + +/* + * If the port was already initialised (eg, by a boot loader), try to determine + * the current setup. + */ +static void __init at91_console_get_options(struct uart_port *port, int *baud, int *parity, int *bits) +{ + unsigned int mr, quot; + +// TODO: CR is a write-only register +// unsigned int cr; +// +// cr = UART_GET_CR(port) & (AT91_US_RXEN | AT91_US_TXEN); +// if (cr == (AT91_US_RXEN | AT91_US_TXEN)) { +// /* ok, the port was enabled */ +// } + + mr = UART_GET_MR(port) & AT91_US_CHRL; + if (mr == AT91_US_CHRL_8) + *bits = 8; + else + *bits = 7; + + mr = UART_GET_MR(port) & AT91_US_PAR; + if (mr == AT91_US_PAR_EVEN) + *parity = 'e'; + else if (mr == AT91_US_PAR_ODD) + *parity = 'o'; + + quot = UART_GET_BRGR(port); + *baud = port->uartclk / (16 * (quot)); +} + +static int __init at91_console_setup(struct console *co, char *options) +{ + struct uart_port *port; + int baud = 115200; + int bits = 8; + int parity = 'n'; + int flow = 'n'; + + /* + * Check whether an invalid uart number has been specified, and + * if so, search for the first available port that does have + * console support. + */ + port = uart_get_console(at91_ports, AT91_NR_UART, co); + + /* + * Enable the serial console, in-case bootloader did not do it. + */ + at91_sys_write(AT91_PMC_PCER, 1 << port->irq); /* enable clock */ + UART_PUT_IDR(port, -1); /* disable interrupts */ + UART_PUT_CR(port, AT91_US_RSTSTA | AT91_US_RSTRX); + UART_PUT_CR(port, AT91_US_TXEN | AT91_US_RXEN); + + if (options) + uart_parse_options(options, &baud, &parity, &bits, &flow); + else + at91_console_get_options(port, &baud, &parity, &bits); + + return uart_set_options(port, co, baud, parity, bits, flow); +} + +static struct uart_driver at91_uart; + +static struct console at91_console = { + .name = AT91_DEVICENAME, + .write = at91_console_write, + .device = uart_console_device, + .setup = at91_console_setup, + .flags = CON_PRINTBUFFER, + .index = -1, + .data = &at91_uart, +}; + +#define AT91_CONSOLE_DEVICE &at91_console + +static int __init at91_console_init(void) +{ + at91_init_ports(); + + at91_console.index = at91_console_port; + register_console(&at91_console); + return 0; +} +console_initcall(at91_console_init); + +#else +#define AT91_CONSOLE_DEVICE NULL +#endif + +static struct uart_driver at91_uart = { + .owner = THIS_MODULE, + .driver_name = AT91_DEVICENAME, + .dev_name = AT91_DEVICENAME, + .devfs_name = AT91_DEVICENAME, + .major = SERIAL_AT91_MAJOR, + .minor = MINOR_START, + .nr = AT91_NR_UART, + .cons = AT91_CONSOLE_DEVICE, +}; + +static int __init at91_serial_init(void) +{ + int ret, i; + + at91_init_ports(); + + ret = uart_register_driver(&at91_uart); + if (ret) + return ret; + + for (i = 0; i < AT91_NR_UART; i++) { + if (at91_serial_map[i] >= 0) + uart_add_one_port(&at91_uart, &at91_ports[i]); + } + + return 0; +} + +static void __exit at91_serial_exit(void) +{ + int i; + + for (i = 0; i < AT91_NR_UART; i++) { + if (at91_serial_map[i] >= 0) + uart_remove_one_port(&at91_uart, &at91_ports[i]); + } + + uart_unregister_driver(&at91_uart); +} + +module_init(at91_serial_init); +module_exit(at91_serial_exit); + +MODULE_AUTHOR("Rick Bronson"); +MODULE_DESCRIPTION("AT91 generic serial port driver"); +MODULE_LICENSE("GPL"); diff --git a/include/asm-arm/arch-at91rm9200/at91rm9200_pdc.h b/include/asm-arm/arch-at91rm9200/at91rm9200_pdc.h new file mode 100644 index 000000000000..ce1150d4438d --- /dev/null +++ b/include/asm-arm/arch-at91rm9200/at91rm9200_pdc.h @@ -0,0 +1,36 @@ +/* + * include/asm-arm/arch-at91rm9200/at91rm9200_pdc.h + * + * Copyright (C) 2005 Ivan Kokshaysky + * Copyright (C) SAN People + * + * Peripheral Data Controller (PDC) registers. + * Based on AT91RM9200 datasheet revision E. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +#ifndef AT91RM9200_PDC_H +#define AT91RM9200_PDC_H + +#define AT91_PDC_RPR 0x100 /* Receive Pointer Register */ +#define AT91_PDC_RCR 0x104 /* Receive Counter Register */ +#define AT91_PDC_TPR 0x108 /* Transmit Pointer Register */ +#define AT91_PDC_TCR 0x10c /* Transmit Counter Register */ +#define AT91_PDC_RNPR 0x110 /* Receive Next Pointer Register */ +#define AT91_PDC_RNCR 0x114 /* Receive Next Counter Register */ +#define AT91_PDC_TNPR 0x118 /* Transmit Next Pointer Register */ +#define AT91_PDC_TNCR 0x11c /* Transmit Next Counter Register */ + +#define AT91_PDC_PTCR 0x120 /* Transfer Control Register */ +#define AT91_PDC_RXTEN (1 << 0) /* Receiver Transfer Enable */ +#define AT91_PDC_RXTDIS (1 << 1) /* Receiver Transfer Disable */ +#define AT91_PDC_TXTEN (1 << 8) /* Transmitter Transfer Enable */ +#define AT91_PDC_TXTDIS (1 << 9) /* Transmitter Transfer Disable */ + +#define AT91_PDC_PTSR 0x124 /* Transfer Status Register */ + +#endif diff --git a/include/asm-arm/arch-at91rm9200/at91rm9200_usart.h b/include/asm-arm/arch-at91rm9200/at91rm9200_usart.h new file mode 100644 index 000000000000..79f851e31b9c --- /dev/null +++ b/include/asm-arm/arch-at91rm9200/at91rm9200_usart.h @@ -0,0 +1,123 @@ +/* + * include/asm-arm/arch-at91rm9200/at91rm9200_usart.h + * + * Copyright (C) 2005 Ivan Kokshaysky + * Copyright (C) SAN People + * + * USART registers. + * Based on AT91RM9200 datasheet revision E. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +#ifndef AT91RM9200_USART_H +#define AT91RM9200_USART_H + +#define AT91_US_CR 0x00 /* Control Register */ +#define AT91_US_RSTRX (1 << 2) /* Reset Receiver */ +#define AT91_US_RSTTX (1 << 3) /* Reset Transmitter */ +#define AT91_US_RXEN (1 << 4) /* Receiver Enable */ +#define AT91_US_RXDIS (1 << 5) /* Receiver Disable */ +#define AT91_US_TXEN (1 << 6) /* Transmitter Enable */ +#define AT91_US_TXDIS (1 << 7) /* Transmitter Disable */ +#define AT91_US_RSTSTA (1 << 8) /* Reset Status Bits */ +#define AT91_US_STTBRK (1 << 9) /* Start Break */ +#define AT91_US_STPBRK (1 << 10) /* Stop Break */ +#define AT91_US_STTTO (1 << 11) /* Start Time-out */ +#define AT91_US_SENDA (1 << 12) /* Send Address */ +#define AT91_US_RSTIT (1 << 13) /* Reset Iterations */ +#define AT91_US_RSTNACK (1 << 14) /* Reset Non Acknowledge */ +#define AT91_US_RETTO (1 << 15) /* Rearm Time-out */ +#define AT91_US_DTREN (1 << 16) /* Data Terminal Ready Enable */ +#define AT91_US_DTRDIS (1 << 17) /* Data Terminal Ready Disable */ +#define AT91_US_RTSEN (1 << 18) /* Request To Send Enable */ +#define AT91_US_RTSDIS (1 << 19) /* Request To Send Disable */ + +#define AT91_US_MR 0x04 /* Mode Register */ +#define AT91_US_USMODE (0xf << 0) /* Mode of the USART */ +#define AT91_US_USMODE_NORMAL 0 +#define AT91_US_USMODE_RS485 1 +#define AT91_US_USMODE_HWHS 2 +#define AT91_US_USMODE_MODEM 3 +#define AT91_US_USMODE_ISO7816_T0 4 +#define AT91_US_USMODE_ISO7816_T1 6 +#define AT91_US_USMODE_IRDA 8 +#define AT91_US_USCLKS (3 << 4) /* Clock Selection */ +#define AT91_US_CHRL (3 << 6) /* Character Length */ +#define AT91_US_CHRL_5 (0 << 6) +#define AT91_US_CHRL_6 (1 << 6) +#define AT91_US_CHRL_7 (2 << 6) +#define AT91_US_CHRL_8 (3 << 6) +#define AT91_US_SYNC (1 << 8) /* Synchronous Mode Select */ +#define AT91_US_PAR (7 << 9) /* Parity Type */ +#define AT91_US_PAR_EVEN (0 << 9) +#define AT91_US_PAR_ODD (1 << 9) +#define AT91_US_PAR_SPACE (2 << 9) +#define AT91_US_PAR_MARK (3 << 9) +#define AT91_US_PAR_NONE (4 << 9) +#define AT91_US_PAR_MULTI_DROP (6 << 9) +#define AT91_US_NBSTOP (3 << 12) /* Number of Stop Bits */ +#define AT91_US_NBSTOP_1 (0 << 12) +#define AT91_US_NBSTOP_1_5 (1 << 12) +#define AT91_US_NBSTOP_2 (2 << 12) +#define AT91_US_CHMODE (3 << 14) /* Channel Mode */ +#define AT91_US_CHMODE_NORMAL (0 << 14) +#define AT91_US_CHMODE_ECHO (1 << 14) +#define AT91_US_CHMODE_LOC_LOOP (2 << 14) +#define AT91_US_CHMODE_REM_LOOP (3 << 14) +#define AT91_US_MSBF (1 << 16) /* Bit Order */ +#define AT91_US_MODE9 (1 << 17) /* 9-bit Character Length */ +#define AT91_US_CLKO (1 << 18) /* Clock Output Select */ +#define AT91_US_OVER (1 << 19) /* Oversampling Mode */ +#define AT91_US_INACK (1 << 20) /* Inhibit Non Acknowledge */ +#define AT91_US_DSNACK (1 << 21) /* Disable Successive NACK */ +#define AT91_US_MAX_ITER (7 << 24) /* Max Iterations */ +#define AT91_US_FILTER (1 << 28) /* Infrared Receive Line Filter */ + +#define AT91_US_IER 0x08 /* Interrupt Enable Register */ +#define AT91_US_RXRDY (1 << 0) /* Receiver Ready */ +#define AT91_US_TXRDY (1 << 1) /* Transmitter Ready */ +#define AT91_US_RXBRK (1 << 2) /* Break Received / End of Break */ +#define AT91_US_ENDRX (1 << 3) /* End of Receiver Transfer */ +#define AT91_US_ENDTX (1 << 4) /* End of Transmitter Transfer */ +#define AT91_US_OVRE (1 << 5) /* Overrun Error */ +#define AT91_US_FRAME (1 << 6) /* Framing Error */ +#define AT91_US_PARE (1 << 7) /* Parity Error */ +#define AT91_US_TIMEOUT (1 << 8) /* Receiver Time-out */ +#define AT91_US_TXEMPTY (1 << 9) /* Transmitter Empty */ +#define AT91_US_ITERATION (1 << 10) /* Max number of Repetitions Reached */ +#define AT91_US_TXBUFE (1 << 11) /* Transmission Buffer Empty */ +#define AT91_US_RXBUFF (1 << 12) /* Reception Buffer Full */ +#define AT91_US_NACK (1 << 13) /* Non Acknowledge */ +#define AT91_US_RIIC (1 << 16) /* Ring Indicator Input Change */ +#define AT91_US_DSRIC (1 << 17) /* Data Set Ready Input Change */ +#define AT91_US_DCDIC (1 << 18) /* Data Carrier Detect Input Change */ +#define AT91_US_CTSIC (1 << 19) /* Clear to Send Input Change */ +#define AT91_US_RI (1 << 20) /* RI */ +#define AT91_US_DSR (1 << 21) /* DSR */ +#define AT91_US_DCD (1 << 22) /* DCD */ +#define AT91_US_CTS (1 << 23) /* CTS */ + +#define AT91_US_IDR 0x0c /* Interrupt Disable Register */ +#define AT91_US_IMR 0x10 /* Interrupt Mask Register */ +#define AT91_US_CSR 0x14 /* Channel Status Register */ +#define AT91_US_RHR 0x18 /* Receiver Holding Register */ +#define AT91_US_THR 0x1c /* Transmitter Holding Register */ + +#define AT91_US_BRGR 0x20 /* Baud Rate Generator Register */ +#define AT91_US_CD (0xffff << 0) /* Clock Divider */ + +#define AT91_US_RTOR 0x24 /* Receiver Time-out Register */ +#define AT91_US_TO (0xffff << 0) /* Time-out Value */ + +#define AT91_US_TTGR 0x28 /* Transmitter Timeguard Register */ +#define AT91_US_TG (0xff << 0) /* Timeguard Value */ + +#define AT91_US_FIDI 0x40 /* FI DI Ratio Register */ +#define AT91_US_NER 0x44 /* Number of Errors Register */ +#define AT91_US_IF 0x4c /* IrDA Filter Register */ + +#endif diff --git a/include/asm-arm/byteorder.h b/include/asm-arm/byteorder.h index 741f5bc5d016..17eaf8bdf092 100644 --- a/include/asm-arm/byteorder.h +++ b/include/asm-arm/byteorder.h @@ -22,7 +22,16 @@ static inline __attribute_const__ __u32 ___arch__swab32(__u32 x) { __u32 t; - t = x ^ ((x << 16) | (x >> 16)); /* eor r1,r0,r0,ror #16 */ + if (__builtin_constant_p(x)) { + t = x ^ ((x << 16) | (x >> 16)); /* eor r1,r0,r0,ror #16 */ + } else { + /* + * The compiler needs a bit of a hint here to always do the + * right thing and not screw it up to different degrees + * depending on the gcc version. + */ + asm ("eor\t%0, %1, %1, ror #16" : "=r" (t) : "r" (x)); + } x = (x << 24) | (x >> 8); /* mov r0,r0,ror #8 */ t &= ~0x00FF0000; /* bic r1,r1,#0x00FF0000 */ x ^= (t >> 8); /* eor r0,r0,r1,lsr #8 */ diff --git a/include/asm-arm/mach/serial_at91rm9200.h b/include/asm-arm/mach/serial_at91rm9200.h new file mode 100644 index 000000000000..98f4b0cb883c --- /dev/null +++ b/include/asm-arm/mach/serial_at91rm9200.h @@ -0,0 +1,36 @@ +/* + * linux/include/asm-arm/mach/serial_at91rm9200.h + * + * Based on serial_sa1100.h by Nicolas Pitre + * + * Copyright (C) 2002 ATMEL Rousset + * + * Low level machine dependent UART functions. + */ +#include + +struct uart_port; + +/* + * This is a temporary structure for registering these + * functions; it is intended to be discarded after boot. + */ +struct at91rm9200_port_fns { + void (*set_mctrl)(struct uart_port *, u_int); + u_int (*get_mctrl)(struct uart_port *); + void (*enable_ms)(struct uart_port *); + void (*pm)(struct uart_port *, u_int, u_int); + int (*set_wake)(struct uart_port *, u_int); + int (*open)(struct uart_port *); + void (*close)(struct uart_port *); +}; + +#if defined(CONFIG_SERIAL_AT91) +void at91_register_uart_fns(struct at91rm9200_port_fns *fns); +void at91_register_uart(int idx, int port); +#else +#define at91_register_uart_fns(fns) do { } while (0) +#define at91_register_uart(idx,port) do { } while (0) +#endif + + diff --git a/include/asm-arm/memory.h b/include/asm-arm/memory.h index 3d7f08bd9030..b4e1146ab682 100644 --- a/include/asm-arm/memory.h +++ b/include/asm-arm/memory.h @@ -25,6 +25,7 @@ #include #include #include +#include #ifndef TASK_SIZE /* @@ -47,6 +48,14 @@ #define PAGE_OFFSET UL(0xc0000000) #endif +/* + * Size of DMA-consistent memory region. Must be multiple of 2M, + * between 2MB and 14MB inclusive. + */ +#ifndef CONSISTENT_DMA_SIZE +#define CONSISTENT_DMA_SIZE SZ_2M +#endif + /* * Physical vs virtual RAM address space conversion. These are * private definitions which should NOT be used outside memory.h diff --git a/include/linux/serial_core.h b/include/linux/serial_core.h index e3710d7e260a..a8187c3c8a7b 100644 --- a/include/linux/serial_core.h +++ b/include/linux/serial_core.h @@ -67,6 +67,9 @@ /* Parisc type numbers. */ #define PORT_MUX 48 +/* Atmel AT91RM9200 SoC */ +#define PORT_AT91RM9200 49 + /* Macintosh Zilog type numbers */ #define PORT_MAC_ZILOG 50 /* m68k : not yet implemented */ #define PORT_PMAC_ZILOG 51