Merge remote-tracking branch 'regulator/topic/mc13892' into regulator-next
This commit is contained in:
commit
c99f21c276
|
@ -164,6 +164,14 @@ static const unsigned int mc13892_sw1[] = {
|
|||
1350000, 1375000
|
||||
};
|
||||
|
||||
/*
|
||||
* Note: this table is used to derive SWxVSEL by index into
|
||||
* the array. Offset the values by the index of 1100000uV
|
||||
* to get the actual register value for that voltage selector
|
||||
* if the HI bit is to be set as well.
|
||||
*/
|
||||
#define MC13892_SWxHI_SEL_OFFSET 20
|
||||
|
||||
static const unsigned int mc13892_sw[] = {
|
||||
600000, 625000, 650000, 675000, 700000, 725000,
|
||||
750000, 775000, 800000, 825000, 850000, 875000,
|
||||
|
@ -239,7 +247,6 @@ static const unsigned int mc13892_pwgtdrv[] = {
|
|||
};
|
||||
|
||||
static struct regulator_ops mc13892_gpo_regulator_ops;
|
||||
/* sw regulators need special care due to the "hi bit" */
|
||||
static struct regulator_ops mc13892_sw_regulator_ops;
|
||||
|
||||
|
||||
|
@ -396,7 +403,7 @@ static int mc13892_sw_regulator_get_voltage_sel(struct regulator_dev *rdev)
|
|||
{
|
||||
struct mc13xxx_regulator_priv *priv = rdev_get_drvdata(rdev);
|
||||
int ret, id = rdev_get_id(rdev);
|
||||
unsigned int val;
|
||||
unsigned int val, selector;
|
||||
|
||||
dev_dbg(rdev_get_dev(rdev), "%s id: %d\n", __func__, id);
|
||||
|
||||
|
@ -407,12 +414,28 @@ static int mc13892_sw_regulator_get_voltage_sel(struct regulator_dev *rdev)
|
|||
if (ret)
|
||||
return ret;
|
||||
|
||||
val = (val & mc13892_regulators[id].vsel_mask)
|
||||
>> mc13892_regulators[id].vsel_shift;
|
||||
/*
|
||||
* Figure out if the HI bit is set inside the switcher mode register
|
||||
* since this means the selector value we return is at a different
|
||||
* offset into the selector table.
|
||||
*
|
||||
* According to the MC13892 documentation note 59 (Table 47) the SW1
|
||||
* buck switcher does not support output range programming therefore
|
||||
* the HI bit must always remain 0. So do not do anything strange if
|
||||
* our register is MC13892_SWITCHERS0.
|
||||
*/
|
||||
|
||||
dev_dbg(rdev_get_dev(rdev), "%s id: %d val: %d\n", __func__, id, val);
|
||||
selector = val & mc13892_regulators[id].vsel_mask;
|
||||
|
||||
return val;
|
||||
if ((mc13892_regulators[id].vsel_reg != MC13892_SWITCHERS0) &&
|
||||
(val & MC13892_SWITCHERS0_SWxHI)) {
|
||||
selector += MC13892_SWxHI_SEL_OFFSET;
|
||||
}
|
||||
|
||||
dev_dbg(rdev_get_dev(rdev), "%s id: %d val: 0x%08x selector: %d\n",
|
||||
__func__, id, val, selector);
|
||||
|
||||
return selector;
|
||||
}
|
||||
|
||||
static int mc13892_sw_regulator_set_voltage_sel(struct regulator_dev *rdev,
|
||||
|
@ -425,18 +448,35 @@ static int mc13892_sw_regulator_set_voltage_sel(struct regulator_dev *rdev,
|
|||
|
||||
volt = rdev->desc->volt_table[selector];
|
||||
mask = mc13892_regulators[id].vsel_mask;
|
||||
reg_value = selector << mc13892_regulators[id].vsel_shift;
|
||||
reg_value = selector;
|
||||
|
||||
if (volt > 1375000) {
|
||||
mask |= MC13892_SWITCHERS0_SWxHI;
|
||||
reg_value |= MC13892_SWITCHERS0_SWxHI;
|
||||
} else if (volt < 1100000) {
|
||||
mask |= MC13892_SWITCHERS0_SWxHI;
|
||||
reg_value &= ~MC13892_SWITCHERS0_SWxHI;
|
||||
/*
|
||||
* Don't mess with the HI bit or support HI voltage offsets for SW1.
|
||||
*
|
||||
* Since the get_voltage_sel callback has given a fudged value for
|
||||
* the selector offset, we need to back out that offset if HI is
|
||||
* to be set so we write the correct value to the register.
|
||||
*
|
||||
* The HI bit addition and selector offset handling COULD be more
|
||||
* complicated by shifting and masking off the voltage selector part
|
||||
* of the register then logical OR it back in, but since the selector
|
||||
* is at bits 4:0 there is very little point. This makes the whole
|
||||
* thing more readable and we do far less work.
|
||||
*/
|
||||
|
||||
if (mc13892_regulators[id].vsel_reg != MC13892_SWITCHERS0) {
|
||||
if (volt > 1375000) {
|
||||
reg_value -= MC13892_SWxHI_SEL_OFFSET;
|
||||
reg_value |= MC13892_SWITCHERS0_SWxHI;
|
||||
mask |= MC13892_SWITCHERS0_SWxHI;
|
||||
} else if (volt < 1100000) {
|
||||
reg_value &= ~MC13892_SWITCHERS0_SWxHI;
|
||||
mask |= MC13892_SWITCHERS0_SWxHI;
|
||||
}
|
||||
}
|
||||
|
||||
mc13xxx_lock(priv->mc13xxx);
|
||||
ret = mc13xxx_reg_rmw(priv->mc13xxx, mc13892_regulators[id].reg, mask,
|
||||
ret = mc13xxx_reg_rmw(priv->mc13xxx, mc13892_regulators[id].vsel_reg, mask,
|
||||
reg_value);
|
||||
mc13xxx_unlock(priv->mc13xxx);
|
||||
|
||||
|
@ -495,15 +535,18 @@ static int mc13892_regulator_probe(struct platform_device *pdev)
|
|||
struct mc13xxx_regulator_init_data *mc13xxx_data;
|
||||
struct regulator_config config = { };
|
||||
int i, ret;
|
||||
int num_regulators = 0;
|
||||
int num_regulators = 0, num_parsed;
|
||||
u32 val;
|
||||
|
||||
num_regulators = mc13xxx_get_num_regulators_dt(pdev);
|
||||
|
||||
if (num_regulators <= 0 && pdata)
|
||||
num_regulators = pdata->num_regulators;
|
||||
if (num_regulators <= 0)
|
||||
return -EINVAL;
|
||||
|
||||
num_parsed = num_regulators;
|
||||
|
||||
priv = devm_kzalloc(&pdev->dev, sizeof(*priv) +
|
||||
num_regulators * sizeof(priv->regulators[0]),
|
||||
GFP_KERNEL);
|
||||
|
@ -520,7 +563,7 @@ static int mc13892_regulator_probe(struct platform_device *pdev)
|
|||
if (ret)
|
||||
goto err_unlock;
|
||||
|
||||
/* enable switch auto mode */
|
||||
/* enable switch auto mode (on 2.0A silicon only) */
|
||||
if ((val & 0x0000FFFF) == 0x45d0) {
|
||||
ret = mc13xxx_reg_rmw(mc13892, MC13892_SWITCHERS4,
|
||||
MC13892_SWITCHERS4_SW1MODE_M |
|
||||
|
@ -546,7 +589,39 @@ static int mc13892_regulator_probe(struct platform_device *pdev)
|
|||
= mc13892_vcam_get_mode;
|
||||
|
||||
mc13xxx_data = mc13xxx_parse_regulators_dt(pdev, mc13892_regulators,
|
||||
ARRAY_SIZE(mc13892_regulators));
|
||||
ARRAY_SIZE(mc13892_regulators),
|
||||
&num_parsed);
|
||||
|
||||
/*
|
||||
* Perform a little sanity check on the regulator tree - if we found
|
||||
* a number of regulators from mc13xxx_get_num_regulators_dt and
|
||||
* then parsed a smaller number in mc13xxx_parse_regulators_dt then
|
||||
* there is a regulator defined in the regulators node which has
|
||||
* not matched any usable regulator in the driver. In this case,
|
||||
* there is one missing and what will happen is the first regulator
|
||||
* will get registered again.
|
||||
*
|
||||
* Fix this by basically making our number of registerable regulators
|
||||
* equal to the number of regulators we parsed. We are allocating
|
||||
* too much memory for priv, but this is unavoidable at this point.
|
||||
*
|
||||
* As an example of how this can happen, try making a typo in your
|
||||
* regulators node (vviohi {} instead of viohi {}) so that the name
|
||||
* does not match..
|
||||
*
|
||||
* The check will basically pass for platform data (non-DT) because
|
||||
* mc13xxx_parse_regulators_dt for !CONFIG_OF will not touch num_parsed.
|
||||
*
|
||||
*/
|
||||
if (num_parsed != num_regulators) {
|
||||
dev_warn(&pdev->dev,
|
||||
"parsed %d != regulators %d - check your device tree!\n",
|
||||
num_parsed, num_regulators);
|
||||
|
||||
num_regulators = num_parsed;
|
||||
priv->num_regulators = num_regulators;
|
||||
}
|
||||
|
||||
for (i = 0; i < num_regulators; i++) {
|
||||
struct regulator_init_data *init_data;
|
||||
struct regulator_desc *desc;
|
||||
|
|
|
@ -181,12 +181,14 @@ EXPORT_SYMBOL_GPL(mc13xxx_get_num_regulators_dt);
|
|||
|
||||
struct mc13xxx_regulator_init_data *mc13xxx_parse_regulators_dt(
|
||||
struct platform_device *pdev, struct mc13xxx_regulator *regulators,
|
||||
int num_regulators)
|
||||
int num_regulators, int *num_parsed)
|
||||
{
|
||||
struct mc13xxx_regulator_priv *priv = platform_get_drvdata(pdev);
|
||||
struct mc13xxx_regulator_init_data *data, *p;
|
||||
struct device_node *parent, *child;
|
||||
int i;
|
||||
int i, parsed = 0;
|
||||
|
||||
*num_parsed = 0;
|
||||
|
||||
of_node_get(pdev->dev.parent->of_node);
|
||||
parent = of_find_node_by_name(pdev->dev.parent->of_node, "regulators");
|
||||
|
@ -203,16 +205,20 @@ struct mc13xxx_regulator_init_data *mc13xxx_parse_regulators_dt(
|
|||
for (i = 0; i < num_regulators; i++) {
|
||||
if (!of_node_cmp(child->name,
|
||||
regulators[i].desc.name)) {
|
||||
|
||||
p->id = i;
|
||||
p->init_data = of_get_regulator_init_data(
|
||||
&pdev->dev, child);
|
||||
p->node = child;
|
||||
p++;
|
||||
|
||||
parsed++;
|
||||
break;
|
||||
}
|
||||
}
|
||||
}
|
||||
|
||||
*num_parsed = parsed;
|
||||
return data;
|
||||
}
|
||||
EXPORT_SYMBOL_GPL(mc13xxx_parse_regulators_dt);
|
||||
|
|
|
@ -39,7 +39,7 @@ extern int mc13xxx_fixed_regulator_set_voltage(struct regulator_dev *rdev,
|
|||
extern int mc13xxx_get_num_regulators_dt(struct platform_device *pdev);
|
||||
extern struct mc13xxx_regulator_init_data *mc13xxx_parse_regulators_dt(
|
||||
struct platform_device *pdev, struct mc13xxx_regulator *regulators,
|
||||
int num_regulators);
|
||||
int num_regulators, int *num_parsed);
|
||||
#else
|
||||
static inline int mc13xxx_get_num_regulators_dt(struct platform_device *pdev)
|
||||
{
|
||||
|
@ -48,7 +48,7 @@ static inline int mc13xxx_get_num_regulators_dt(struct platform_device *pdev)
|
|||
|
||||
static inline struct mc13xxx_regulator_init_data *mc13xxx_parse_regulators_dt(
|
||||
struct platform_device *pdev, struct mc13xxx_regulator *regulators,
|
||||
int num_regulators)
|
||||
int num_regulators, int *num_parsed)
|
||||
{
|
||||
return NULL;
|
||||
}
|
||||
|
|
Loading…
Reference in a new issue