Input: add driver for Cypress APA I2C Trackpad

This patch introduces a driver for Cypress All Points Addressable
I2C Trackpad, including the ones in 2012 Samsung Chromebooks.

This device is compatible with MT protocol type B, providing identifiable
contacts.

Signed-off-by: Dudley Du <dudl@cypress.com>
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Benson Leung <bleung@chromium.org>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This commit is contained in:
Benson Leung 2013-01-09 16:25:11 -08:00 committed by Dmitry Torokhov
parent 236d6a77ee
commit d7e34d12ba
3 changed files with 817 additions and 0 deletions

View file

@ -203,6 +203,18 @@ config MOUSE_BCM5974
To compile this driver as a module, choose M here: the
module will be called bcm5974.
config MOUSE_CYAPA
tristate "Cypress APA I2C Trackpad support"
depends on I2C
help
This driver adds support for Cypress All Points Addressable (APA)
I2C Trackpads, including the ones used in 2012 Samsung Chromebooks.
Say Y here if you have a Cypress APA I2C Trackpad.
To compile this driver as a module, choose M here: the module will be
called cyapa.
config MOUSE_INPORT
tristate "InPort/MS/ATIXL busmouse"
depends on ISA

View file

@ -8,6 +8,7 @@ obj-$(CONFIG_MOUSE_AMIGA) += amimouse.o
obj-$(CONFIG_MOUSE_APPLETOUCH) += appletouch.o
obj-$(CONFIG_MOUSE_ATARI) += atarimouse.o
obj-$(CONFIG_MOUSE_BCM5974) += bcm5974.o
obj-$(CONFIG_MOUSE_CYAPA) += cyapa.o
obj-$(CONFIG_MOUSE_GPIO) += gpio_mouse.o
obj-$(CONFIG_MOUSE_INPORT) += inport.o
obj-$(CONFIG_MOUSE_LOGIBM) += logibm.o

804
drivers/input/mouse/cyapa.c Normal file
View file

@ -0,0 +1,804 @@
/*
* Cypress APA trackpad with I2C interface
*
* Author: Dudley Du <dudl@cypress.com>
* Further cleanup and restructuring by:
* Daniel Kurtz <djkurtz@chromium.org>
* Benson Leung <bleung@chromium.org>
*
* Copyright (C) 2011-2012 Cypress Semiconductor, Inc.
* Copyright (C) 2011-2012 Google, Inc.
*
* This file is subject to the terms and conditions of the GNU General Public
* License. See the file COPYING in the main directory of this archive for
* more details.
*/
#include <linux/delay.h>
#include <linux/i2c.h>
#include <linux/input.h>
#include <linux/input/mt.h>
#include <linux/interrupt.h>
#include <linux/module.h>
#include <linux/slab.h>
/* APA trackpad firmware generation */
#define CYAPA_GEN3 0x03 /* support MT-protocol B with tracking ID. */
#define CYAPA_NAME "Cypress APA Trackpad (cyapa)"
/* commands for read/write registers of Cypress trackpad */
#define CYAPA_CMD_SOFT_RESET 0x00
#define CYAPA_CMD_POWER_MODE 0x01
#define CYAPA_CMD_DEV_STATUS 0x02
#define CYAPA_CMD_GROUP_DATA 0x03
#define CYAPA_CMD_GROUP_CMD 0x04
#define CYAPA_CMD_GROUP_QUERY 0x05
#define CYAPA_CMD_BL_STATUS 0x06
#define CYAPA_CMD_BL_HEAD 0x07
#define CYAPA_CMD_BL_CMD 0x08
#define CYAPA_CMD_BL_DATA 0x09
#define CYAPA_CMD_BL_ALL 0x0a
#define CYAPA_CMD_BLK_PRODUCT_ID 0x0b
#define CYAPA_CMD_BLK_HEAD 0x0c
/* report data start reg offset address. */
#define DATA_REG_START_OFFSET 0x0000
#define BL_HEAD_OFFSET 0x00
#define BL_DATA_OFFSET 0x10
/*
* Operational Device Status Register
*
* bit 7: Valid interrupt source
* bit 6 - 4: Reserved
* bit 3 - 2: Power status
* bit 1 - 0: Device status
*/
#define REG_OP_STATUS 0x00
#define OP_STATUS_SRC 0x80
#define OP_STATUS_POWER 0x0c
#define OP_STATUS_DEV 0x03
#define OP_STATUS_MASK (OP_STATUS_SRC | OP_STATUS_POWER | OP_STATUS_DEV)
/*
* Operational Finger Count/Button Flags Register
*
* bit 7 - 4: Number of touched finger
* bit 3: Valid data
* bit 2: Middle Physical Button
* bit 1: Right Physical Button
* bit 0: Left physical Button
*/
#define REG_OP_DATA1 0x01
#define OP_DATA_VALID 0x08
#define OP_DATA_MIDDLE_BTN 0x04
#define OP_DATA_RIGHT_BTN 0x02
#define OP_DATA_LEFT_BTN 0x01
#define OP_DATA_BTN_MASK (OP_DATA_MIDDLE_BTN | OP_DATA_RIGHT_BTN | \
OP_DATA_LEFT_BTN)
/*
* Bootloader Status Register
*
* bit 7: Busy
* bit 6 - 5: Reserved
* bit 4: Bootloader running
* bit 3 - 1: Reserved
* bit 0: Checksum valid
*/
#define REG_BL_STATUS 0x01
#define BL_STATUS_BUSY 0x80
#define BL_STATUS_RUNNING 0x10
#define BL_STATUS_DATA_VALID 0x08
#define BL_STATUS_CSUM_VALID 0x01
/*
* Bootloader Error Register
*
* bit 7: Invalid
* bit 6: Invalid security key
* bit 5: Bootloading
* bit 4: Command checksum
* bit 3: Flash protection error
* bit 2: Flash checksum error
* bit 1 - 0: Reserved
*/
#define REG_BL_ERROR 0x02
#define BL_ERROR_INVALID 0x80
#define BL_ERROR_INVALID_KEY 0x40
#define BL_ERROR_BOOTLOADING 0x20
#define BL_ERROR_CMD_CSUM 0x10
#define BL_ERROR_FLASH_PROT 0x08
#define BL_ERROR_FLASH_CSUM 0x04
#define BL_STATUS_SIZE 3 /* length of bootloader status registers */
#define BLK_HEAD_BYTES 32
#define PRODUCT_ID_SIZE 16
#define QUERY_DATA_SIZE 27
#define REG_PROTOCOL_GEN_QUERY_OFFSET 20
#define REG_OFFSET_DATA_BASE 0x0000
#define REG_OFFSET_COMMAND_BASE 0x0028
#define REG_OFFSET_QUERY_BASE 0x002a
#define CAPABILITY_LEFT_BTN_MASK (0x01 << 3)
#define CAPABILITY_RIGHT_BTN_MASK (0x01 << 4)
#define CAPABILITY_MIDDLE_BTN_MASK (0x01 << 5)
#define CAPABILITY_BTN_MASK (CAPABILITY_LEFT_BTN_MASK | \
CAPABILITY_RIGHT_BTN_MASK | \
CAPABILITY_MIDDLE_BTN_MASK)
#define CYAPA_OFFSET_SOFT_RESET REG_OFFSET_COMMAND_BASE
#define REG_OFFSET_POWER_MODE (REG_OFFSET_COMMAND_BASE + 1)
#define PWR_MODE_MASK 0xfc
#define PWR_MODE_FULL_ACTIVE (0x3f << 2)
#define PWR_MODE_IDLE (0x05 << 2) /* default sleep time is 50 ms. */
#define PWR_MODE_OFF (0x00 << 2)
#define PWR_STATUS_MASK 0x0c
#define PWR_STATUS_ACTIVE (0x03 << 2)
#define PWR_STATUS_IDLE (0x02 << 2)
#define PWR_STATUS_OFF (0x00 << 2)
/*
* CYAPA trackpad device states.
* Used in register 0x00, bit1-0, DeviceStatus field.
* Other values indicate device is in an abnormal state and must be reset.
*/
#define CYAPA_DEV_NORMAL 0x03
#define CYAPA_DEV_BUSY 0x01
enum cyapa_state {
CYAPA_STATE_OP,
CYAPA_STATE_BL_IDLE,
CYAPA_STATE_BL_ACTIVE,
CYAPA_STATE_BL_BUSY,
CYAPA_STATE_NO_DEVICE,
};
struct cyapa_touch {
/*
* high bits or x/y position value
* bit 7 - 4: high 4 bits of x position value
* bit 3 - 0: high 4 bits of y position value
*/
u8 xy_hi;
u8 x_lo; /* low 8 bits of x position value. */
u8 y_lo; /* low 8 bits of y position value. */
u8 pressure;
/* id range is 1 - 15. It is incremented with every new touch. */
u8 id;
} __packed;
/* The touch.id is used as the MT slot id, thus max MT slot is 15 */
#define CYAPA_MAX_MT_SLOTS 15
struct cyapa_reg_data {
/*
* bit 0 - 1: device status
* bit 3 - 2: power mode
* bit 6 - 4: reserved
* bit 7: interrupt valid bit
*/
u8 device_status;
/*
* bit 7 - 4: number of fingers currently touching pad
* bit 3: valid data check bit
* bit 2: middle mechanism button state if exists
* bit 1: right mechanism button state if exists
* bit 0: left mechanism button state if exists
*/
u8 finger_btn;
/* CYAPA reports up to 5 touches per packet. */
struct cyapa_touch touches[5];
} __packed;
/* The main device structure */
struct cyapa {
enum cyapa_state state;
struct i2c_client *client;
struct input_dev *input;
char phys[32]; /* device physical location */
int irq;
bool irq_wake; /* irq wake is enabled */
/* read from query data region. */
char product_id[16];
u8 btn_capability;
u8 gen;
int max_abs_x;
int max_abs_y;
int physical_size_x;
int physical_size_y;
};
static const u8 bl_deactivate[] = { 0x00, 0xff, 0x3b, 0x00, 0x01, 0x02, 0x03,
0x04, 0x05, 0x06, 0x07 };
static const u8 bl_exit[] = { 0x00, 0xff, 0xa5, 0x00, 0x01, 0x02, 0x03, 0x04,
0x05, 0x06, 0x07 };
struct cyapa_cmd_len {
u8 cmd;
u8 len;
};
static const struct cyapa_cmd_len cyapa_i2c_cmds[] = {
{ CYAPA_OFFSET_SOFT_RESET, 1 },
{ REG_OFFSET_COMMAND_BASE + 1, 1 },
{ REG_OFFSET_DATA_BASE, 1 },
{ REG_OFFSET_DATA_BASE, sizeof(struct cyapa_reg_data) },
{ REG_OFFSET_COMMAND_BASE, 0 },
{ REG_OFFSET_QUERY_BASE, QUERY_DATA_SIZE },
{ BL_HEAD_OFFSET, 3 },
{ BL_HEAD_OFFSET, 16 },
{ BL_HEAD_OFFSET, 16 },
{ BL_DATA_OFFSET, 16 },
{ BL_HEAD_OFFSET, 32 },
{ REG_OFFSET_QUERY_BASE, PRODUCT_ID_SIZE },
{ REG_OFFSET_DATA_BASE, 32 }
};
static ssize_t cyapa_i2c_reg_read_block(struct cyapa *cyapa, u8 reg, size_t len,
u8 *values)
{
return i2c_smbus_read_i2c_block_data(cyapa->client, reg, len, values);
}
static ssize_t cyapa_i2c_reg_write_block(struct cyapa *cyapa, u8 reg,
size_t len, const u8 *values)
{
return i2c_smbus_write_i2c_block_data(cyapa->client, reg, len, values);
}
static s32 cyapa_read_byte(struct cyapa *cyapa, u8 cmd_idx)
{
u8 cmd = cyapa_i2c_cmds[cmd_idx].cmd;
return i2c_smbus_read_byte_data(cyapa->client, cmd);
}
static s32 cyapa_write_byte(struct cyapa *cyapa, u8 cmd_idx, u8 value)
{
u8 cmd = cyapa_i2c_cmds[cmd_idx].cmd;
return i2c_smbus_write_byte_data(cyapa->client, cmd, value);
}
static ssize_t cyapa_read_block(struct cyapa *cyapa, u8 cmd_idx, u8 *values)
{
u8 cmd = cyapa_i2c_cmds[cmd_idx].cmd;
size_t len = cyapa_i2c_cmds[cmd_idx].len;
return cyapa_i2c_reg_read_block(cyapa, cmd, len, values);
}
/*
* Query device for its current operating state.
*
*/
static int cyapa_get_state(struct cyapa *cyapa)
{
int ret;
u8 status[BL_STATUS_SIZE];
cyapa->state = CYAPA_STATE_NO_DEVICE;
/*
* Get trackpad status by reading 3 registers starting from 0.
* If the device is in the bootloader, this will be BL_HEAD.
* If the device is in operation mode, this will be the DATA regs.
*
*/
ret = cyapa_i2c_reg_read_block(cyapa, BL_HEAD_OFFSET, BL_STATUS_SIZE,
status);
if (ret != BL_STATUS_SIZE)
goto error;
if ((status[REG_OP_STATUS] & OP_STATUS_SRC) == OP_STATUS_SRC) {
switch (status[REG_OP_STATUS] & OP_STATUS_DEV) {
case CYAPA_DEV_NORMAL:
case CYAPA_DEV_BUSY:
cyapa->state = CYAPA_STATE_OP;
break;
default:
ret = -EAGAIN;
goto error;
}
} else {
if (status[REG_BL_STATUS] & BL_STATUS_BUSY)
cyapa->state = CYAPA_STATE_BL_BUSY;
else if (status[REG_BL_ERROR] & BL_ERROR_BOOTLOADING)
cyapa->state = CYAPA_STATE_BL_ACTIVE;
else
cyapa->state = CYAPA_STATE_BL_IDLE;
}
return 0;
error:
return (ret < 0) ? ret : -EAGAIN;
}
/*
* Poll device for its status in a loop, waiting up to timeout for a response.
*
* When the device switches state, it usually takes ~300 ms.
* However, when running a new firmware image, the device must calibrate its
* sensors, which can take as long as 2 seconds.
*
* Note: The timeout has granularity of the polling rate, which is 100 ms.
*
* Returns:
* 0 when the device eventually responds with a valid non-busy state.
* -ETIMEDOUT if device never responds (too many -EAGAIN)
* < 0 other errors
*/
static int cyapa_poll_state(struct cyapa *cyapa, unsigned int timeout)
{
int ret;
int tries = timeout / 100;
ret = cyapa_get_state(cyapa);
while ((ret || cyapa->state >= CYAPA_STATE_BL_BUSY) && tries--) {
msleep(100);
ret = cyapa_get_state(cyapa);
}
return (ret == -EAGAIN || ret == -ETIMEDOUT) ? -ETIMEDOUT : ret;
}
static int cyapa_bl_deactivate(struct cyapa *cyapa)
{
int ret;
ret = cyapa_i2c_reg_write_block(cyapa, 0, sizeof(bl_deactivate),
bl_deactivate);
if (ret < 0)
return ret;
/* wait for bootloader to switch to idle state; should take < 100ms */
msleep(100);
ret = cyapa_poll_state(cyapa, 500);
if (ret < 0)
return ret;
if (cyapa->state != CYAPA_STATE_BL_IDLE)
return -EAGAIN;
return 0;
}
/*
* Exit bootloader
*
* Send bl_exit command, then wait 50 - 100 ms to let device transition to
* operational mode. If this is the first time the device's firmware is
* running, it can take up to 2 seconds to calibrate its sensors. So, poll
* the device's new state for up to 2 seconds.
*
* Returns:
* -EIO failure while reading from device
* -EAGAIN device is stuck in bootloader, b/c it has invalid firmware
* 0 device is supported and in operational mode
*/
static int cyapa_bl_exit(struct cyapa *cyapa)
{
int ret;
ret = cyapa_i2c_reg_write_block(cyapa, 0, sizeof(bl_exit), bl_exit);
if (ret < 0)
return ret;
/*
* Wait for bootloader to exit, and operation mode to start.
* Normally, this takes at least 50 ms.
*/
usleep_range(50000, 100000);
/*
* In addition, when a device boots for the first time after being
* updated to new firmware, it must first calibrate its sensors, which
* can take up to an additional 2 seconds.
*/
ret = cyapa_poll_state(cyapa, 2000);
if (ret < 0)
return ret;
if (cyapa->state != CYAPA_STATE_OP)
return -EAGAIN;
return 0;
}
/*
* Set device power mode
*
*/
static int cyapa_set_power_mode(struct cyapa *cyapa, u8 power_mode)
{
struct device *dev = &cyapa->client->dev;
int ret;
u8 power;
if (cyapa->state != CYAPA_STATE_OP)
return 0;
ret = cyapa_read_byte(cyapa, CYAPA_CMD_POWER_MODE);
if (ret < 0)
return ret;
power = ret & ~PWR_MODE_MASK;
power |= power_mode & PWR_MODE_MASK;
ret = cyapa_write_byte(cyapa, CYAPA_CMD_POWER_MODE, power);
if (ret < 0)
dev_err(dev, "failed to set power_mode 0x%02x err = %d\n",
power_mode, ret);
return ret;
}
static int cyapa_get_query_data(struct cyapa *cyapa)
{
u8 query_data[QUERY_DATA_SIZE];
int ret;
if (cyapa->state != CYAPA_STATE_OP)
return -EBUSY;
ret = cyapa_read_block(cyapa, CYAPA_CMD_GROUP_QUERY, query_data);
if (ret < 0)
return ret;
if (ret != QUERY_DATA_SIZE)
return -EIO;
memcpy(&cyapa->product_id[0], &query_data[0], 5);
cyapa->product_id[5] = '-';
memcpy(&cyapa->product_id[6], &query_data[5], 6);
cyapa->product_id[12] = '-';
memcpy(&cyapa->product_id[13], &query_data[11], 2);
cyapa->product_id[15] = '\0';
cyapa->btn_capability = query_data[19] & CAPABILITY_BTN_MASK;
cyapa->gen = query_data[20] & 0x0f;
cyapa->max_abs_x = ((query_data[21] & 0xf0) << 4) | query_data[22];
cyapa->max_abs_y = ((query_data[21] & 0x0f) << 8) | query_data[23];
cyapa->physical_size_x =
((query_data[24] & 0xf0) << 4) | query_data[25];
cyapa->physical_size_y =
((query_data[24] & 0x0f) << 8) | query_data[26];
return 0;
}
/*
* Check if device is operational.
*
* An operational device is responding, has exited bootloader, and has
* firmware supported by this driver.
*
* Returns:
* -EBUSY no device or in bootloader
* -EIO failure while reading from device
* -EAGAIN device is still in bootloader
* if ->state = CYAPA_STATE_BL_IDLE, device has invalid firmware
* -EINVAL device is in operational mode, but not supported by this driver
* 0 device is supported
*/
static int cyapa_check_is_operational(struct cyapa *cyapa)
{
struct device *dev = &cyapa->client->dev;
static const char unique_str[] = "CYTRA";
int ret;
ret = cyapa_poll_state(cyapa, 2000);
if (ret < 0)
return ret;
switch (cyapa->state) {
case CYAPA_STATE_BL_ACTIVE:
ret = cyapa_bl_deactivate(cyapa);
if (ret)
return ret;
/* Fallthrough state */
case CYAPA_STATE_BL_IDLE:
ret = cyapa_bl_exit(cyapa);
if (ret)
return ret;
/* Fallthrough state */
case CYAPA_STATE_OP:
ret = cyapa_get_query_data(cyapa);
if (ret < 0)
return ret;
/* only support firmware protocol gen3 */
if (cyapa->gen != CYAPA_GEN3) {
dev_err(dev, "unsupported protocol version (%d)",
cyapa->gen);
return -EINVAL;
}
/* only support product ID starting with CYTRA */
if (memcmp(cyapa->product_id, unique_str,
sizeof(unique_str) - 1) != 0) {
dev_err(dev, "unsupported product ID (%s)\n",
cyapa->product_id);
return -EINVAL;
}
return 0;
default:
return -EIO;
}
return 0;
}
static irqreturn_t cyapa_irq(int irq, void *dev_id)
{
struct cyapa *cyapa = dev_id;
struct device *dev = &cyapa->client->dev;
struct input_dev *input = cyapa->input;
struct cyapa_reg_data data;
int i;
int ret;
int num_fingers;
if (device_may_wakeup(dev))
pm_wakeup_event(dev, 0);
ret = cyapa_read_block(cyapa, CYAPA_CMD_GROUP_DATA, (u8 *)&data);
if (ret != sizeof(data))
goto out;
if ((data.device_status & OP_STATUS_SRC) != OP_STATUS_SRC ||
(data.device_status & OP_STATUS_DEV) != CYAPA_DEV_NORMAL ||
(data.finger_btn & OP_DATA_VALID) != OP_DATA_VALID) {
goto out;
}
num_fingers = (data.finger_btn >> 4) & 0x0f;
for (i = 0; i < num_fingers; i++) {
const struct cyapa_touch *touch = &data.touches[i];
/* Note: touch->id range is 1 to 15; slots are 0 to 14. */
int slot = touch->id - 1;
input_mt_slot(input, slot);
input_mt_report_slot_state(input, MT_TOOL_FINGER, true);
input_report_abs(input, ABS_MT_POSITION_X,
((touch->xy_hi & 0xf0) << 4) | touch->x_lo);
input_report_abs(input, ABS_MT_POSITION_Y,
((touch->xy_hi & 0x0f) << 8) | touch->y_lo);
input_report_abs(input, ABS_MT_PRESSURE, touch->pressure);
}
input_mt_sync_frame(input);
if (cyapa->btn_capability & CAPABILITY_LEFT_BTN_MASK)
input_report_key(input, BTN_LEFT,
data.finger_btn & OP_DATA_LEFT_BTN);
if (cyapa->btn_capability & CAPABILITY_MIDDLE_BTN_MASK)
input_report_key(input, BTN_MIDDLE,
data.finger_btn & OP_DATA_MIDDLE_BTN);
if (cyapa->btn_capability & CAPABILITY_RIGHT_BTN_MASK)
input_report_key(input, BTN_RIGHT,
data.finger_btn & OP_DATA_RIGHT_BTN);
input_sync(input);
out:
return IRQ_HANDLED;
}
static int cyapa_create_input_dev(struct cyapa *cyapa)
{
struct device *dev = &cyapa->client->dev;
int ret;
struct input_dev *input;
if (!cyapa->physical_size_x || !cyapa->physical_size_y)
return -EINVAL;
input = cyapa->input = input_allocate_device();
if (!input) {
dev_err(dev, "allocate memory for input device failed\n");
return -ENOMEM;
}
input->name = CYAPA_NAME;
input->phys = cyapa->phys;
input->id.bustype = BUS_I2C;
input->id.version = 1;
input->id.product = 0; /* means any product in eventcomm. */
input->dev.parent = &cyapa->client->dev;
input_set_drvdata(input, cyapa);
__set_bit(EV_ABS, input->evbit);
/* finger position */
input_set_abs_params(input, ABS_MT_POSITION_X, 0, cyapa->max_abs_x, 0,
0);
input_set_abs_params(input, ABS_MT_POSITION_Y, 0, cyapa->max_abs_y, 0,
0);
input_set_abs_params(input, ABS_MT_PRESSURE, 0, 255, 0, 0);
input_abs_set_res(input, ABS_MT_POSITION_X,
cyapa->max_abs_x / cyapa->physical_size_x);
input_abs_set_res(input, ABS_MT_POSITION_Y,
cyapa->max_abs_y / cyapa->physical_size_y);
if (cyapa->btn_capability & CAPABILITY_LEFT_BTN_MASK)
__set_bit(BTN_LEFT, input->keybit);
if (cyapa->btn_capability & CAPABILITY_MIDDLE_BTN_MASK)
__set_bit(BTN_MIDDLE, input->keybit);
if (cyapa->btn_capability & CAPABILITY_RIGHT_BTN_MASK)
__set_bit(BTN_RIGHT, input->keybit);
if (cyapa->btn_capability == CAPABILITY_LEFT_BTN_MASK)
__set_bit(INPUT_PROP_BUTTONPAD, input->propbit);
/* handle pointer emulation and unused slots in core */
ret = input_mt_init_slots(input, CYAPA_MAX_MT_SLOTS,
INPUT_MT_POINTER | INPUT_MT_DROP_UNUSED);
if (ret) {
dev_err(dev, "allocate memory for MT slots failed, %d\n", ret);
goto err_free_device;
}
/* Register the device in input subsystem */
ret = input_register_device(input);
if (ret) {
dev_err(dev, "input device register failed, %d\n", ret);
goto err_free_device;
}
return 0;
err_free_device:
input_free_device(input);
cyapa->input = NULL;
return ret;
}
static int cyapa_probe(struct i2c_client *client,
const struct i2c_device_id *dev_id)
{
int ret;
struct cyapa *cyapa;
struct device *dev = &client->dev;
cyapa = kzalloc(sizeof(struct cyapa), GFP_KERNEL);
if (!cyapa) {
dev_err(dev, "allocate memory for cyapa failed\n");
return -ENOMEM;
}
cyapa->gen = CYAPA_GEN3;
cyapa->client = client;
i2c_set_clientdata(client, cyapa);
sprintf(cyapa->phys, "i2c-%d-%04x/input0", client->adapter->nr,
client->addr);
cyapa->state = CYAPA_STATE_NO_DEVICE;
ret = cyapa_check_is_operational(cyapa);
if (ret) {
dev_err(dev, "device not operational, %d\n", ret);
goto err_mem_free;
}
ret = cyapa_create_input_dev(cyapa);
if (ret) {
dev_err(dev, "create input_dev instance failed, %d\n", ret);
goto err_mem_free;
}
ret = cyapa_set_power_mode(cyapa, PWR_MODE_FULL_ACTIVE);
if (ret) {
dev_err(dev, "set active power failed, %d\n", ret);
goto err_unregister_device;
}
cyapa->irq = client->irq;
ret = request_threaded_irq(cyapa->irq,
NULL,
cyapa_irq,
IRQF_TRIGGER_FALLING | IRQF_ONESHOT,
"cyapa",
cyapa);
if (ret) {
dev_err(dev, "IRQ request failed: %d\n, ", ret);
goto err_unregister_device;
}
return 0;
err_unregister_device:
input_unregister_device(cyapa->input);
err_mem_free:
kfree(cyapa);
return ret;
}
static int cyapa_remove(struct i2c_client *client)
{
struct cyapa *cyapa = i2c_get_clientdata(client);
free_irq(cyapa->irq, cyapa);
input_unregister_device(cyapa->input);
cyapa_set_power_mode(cyapa, PWR_MODE_OFF);
kfree(cyapa);
return 0;
}
#ifdef CONFIG_PM_SLEEP
static int cyapa_suspend(struct device *dev)
{
int ret;
u8 power_mode;
struct cyapa *cyapa = dev_get_drvdata(dev);
disable_irq(cyapa->irq);
/*
* Set trackpad device to idle mode if wakeup is allowed,
* otherwise turn off.
*/
power_mode = device_may_wakeup(dev) ? PWR_MODE_IDLE
: PWR_MODE_OFF;
ret = cyapa_set_power_mode(cyapa, power_mode);
if (ret < 0)
dev_err(dev, "set power mode failed, %d\n", ret);
if (device_may_wakeup(dev))
cyapa->irq_wake = (enable_irq_wake(cyapa->irq) == 0);
return 0;
}
static int cyapa_resume(struct device *dev)
{
int ret;
struct cyapa *cyapa = dev_get_drvdata(dev);
if (device_may_wakeup(dev) && cyapa->irq_wake)
disable_irq_wake(cyapa->irq);
ret = cyapa_set_power_mode(cyapa, PWR_MODE_FULL_ACTIVE);
if (ret)
dev_warn(dev, "resume active power failed, %d\n", ret);
enable_irq(cyapa->irq);
return 0;
}
#endif /* CONFIG_PM_SLEEP */
static SIMPLE_DEV_PM_OPS(cyapa_pm_ops, cyapa_suspend, cyapa_resume);
static const struct i2c_device_id cyapa_id_table[] = {
{ "cyapa", 0 },
{ },
};
MODULE_DEVICE_TABLE(i2c, cyapa_id_table);
static struct i2c_driver cyapa_driver = {
.driver = {
.name = "cyapa",
.owner = THIS_MODULE,
.pm = &cyapa_pm_ops,
},
.probe = cyapa_probe,
.remove = cyapa_remove,
.id_table = cyapa_id_table,
};
module_i2c_driver(cyapa_driver);
MODULE_DESCRIPTION("Cypress APA I2C Trackpad Driver");
MODULE_AUTHOR("Dudley Du <dudl@cypress.com>");
MODULE_LICENSE("GPL");