clk: add CLK_RECALC_NEW_RATES clock flag for Exynos cpu clock support
This flag is needed to fix the issue with wrong dividers being setup by Common Clock Framework when using the new Exynos cpu clock support. The issue happens because clk_core_set_rate_nolock() calls clk_calc_new_rates(clk, rate) before both pre/post clock notifiers have a chance to run. In case of Exynos cpu clock support pre/post clock notifiers are registered for mout_apll clock which is a parent of armclk cpu clock and dividers are modified in both pre and post clock notifier. This results in wrong dividers values being later programmed by clk_change_rate(top). To workaround the problem CLK_RECALC_NEW_RATES flag is added and it is set for mout_apll clock later so the correct divider values are re-calculated after both pre and post clock notifiers had run. For example when using "performance" governor on Exynos4210 Origen board the cpufreq-dt driver requests to change the frequency from 1000MHz to 1200MHz and after the change state of the relevant clocks is following: Without use of CLK_GET_RATE_NOCACHE flag: fout_apll rate: 1200000000 fout_apll_div_2 rate: 600000000 mout_clkout_cpu rate: 600000000 div_clkout_cpu rate: 600000000 clkout_cpu rate: 600000000 mout_apll rate: 1200000000 armclk rate: 1200000000 mout_hpm rate: 1200000000 div_copy rate: 300000000 div_hpm rate: 300000000 mout_core rate: 1200000000 div_core rate: 1200000000 div_core2 rate: 1200000000 arm_clk_div_2 rate: 600000000 div_corem0 rate: 300000000 div_corem1 rate: 150000000 div_periph rate: 300000000 div_atb rate: 300000000 div_pclk_dbg rate: 150000000 sclk_apll rate: 1200000000 sclk_apll_div_2 rate: 600000000 With use of CLK_GET_RATE_NOCACHE flag: fout_apll rate: 1200000000 fout_apll_div_2 rate: 600000000 mout_clkout_cpu rate: 600000000 div_clkout_cpu rate: 600000000 clkout_cpu rate: 600000000 mout_apll rate: 1200000000 armclk rate: 1200000000 mout_hpm rate: 1200000000 div_copy rate: 200000000 div_hpm rate: 200000000 mout_core rate: 1200000000 div_core rate: 1200000000 div_core2 rate: 1200000000 arm_clk_div_2 rate: 600000000 div_corem0 rate: 300000000 div_corem1 rate: 150000000 div_periph rate: 300000000 div_atb rate: 240000000 div_pclk_dbg rate: 120000000 sclk_apll rate: 150000000 sclk_apll_div_2 rate: 75000000 Without this change cpufreq-dt driver showed ~10 mA larger energy consumption when compared to cpufreq-exynos one when "performance" cpufreq governor was used on Exynos4210 SoC based Origen board. This issue was probably meant to be workarounded by use of CLK_GET_RATE_NOCACHE and CLK_DIVIDER_READ_ONLY clock flags in the original Exynos cpu clock patchset (in "[PATCH v12 6/6] clk: samsung: remove unused clock aliases and update clock flags" patch) but usage of these flags is not sufficient to fix the issue observed. Cc: Thomas Abraham <thomas.ab@samsung.com> Cc: Tomasz Figa <tomasz.figa@gmail.com> Cc: Mike Turquette <mturquette@linaro.org> Cc: Javier Martinez Canillas <javier.martinez@collabora.co.uk> Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Signed-off-by: Michael Turquette <mturquette@baylibre.com>
This commit is contained in:
parent
d4a4f75cd8
commit
d8d919879e
|
@ -1788,6 +1788,9 @@ static void clk_change_rate(struct clk_core *clk)
|
|||
if (clk->notifier_count && old_rate != clk->rate)
|
||||
__clk_notify(clk, POST_RATE_CHANGE, old_rate, clk->rate);
|
||||
|
||||
if (clk->flags & CLK_RECALC_NEW_RATES)
|
||||
(void)clk_calc_new_rates(clk, clk->new_rate);
|
||||
|
||||
/*
|
||||
* Use safe iteration, as change_rate can actually swap parents
|
||||
* for certain clock types.
|
||||
|
|
|
@ -31,6 +31,7 @@
|
|||
#define CLK_GET_RATE_NOCACHE BIT(6) /* do not use the cached clk rate */
|
||||
#define CLK_SET_RATE_NO_REPARENT BIT(7) /* don't re-parent on rate change */
|
||||
#define CLK_GET_ACCURACY_NOCACHE BIT(8) /* do not use the cached clk accuracy */
|
||||
#define CLK_RECALC_NEW_RATES BIT(9) /* recalc rates after notifications */
|
||||
|
||||
struct clk_hw;
|
||||
struct clk_core;
|
||||
|
|
Loading…
Reference in a new issue