ARM: dts: rockchip: use pin constants to describe gpios
Use macros to describe gpios will make the dts easier to read and write. All the modifications done with sed: sed -i -e 's/ 0 GPIO_ACTIVE_/ RK_PA0 GPIO_ACTIVE_/' arch/arm/boot/dts/rk* sed -i -e 's/ 1 GPIO_ACTIVE_/ RK_PA1 GPIO_ACTIVE_/' arch/arm/boot/dts/rk* sed -i -e 's/ 2 GPIO_ACTIVE_/ RK_PA2 GPIO_ACTIVE_/' arch/arm/boot/dts/rk* ....... ....... sed -i -e 's/ 30 GPIO_ACTIVE_/ RK_PD6 GPIO_ACTIVE_/' arch/arm/boot/dts/rk* sed -i -e 's/ 31 GPIO_ACTIVE_/ RK_PD7 GPIO_ACTIVE_/' arch/arm/boot/dts/rk* Tested with: for i in dts-old/*dtb; do scripts/dtc/dtx_diff $i dts-new/$(basename $i); done Signed-off-by: Andy Yan <andy.yan@rock-chips.com> [also adapted the gpio interrupts] Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This commit is contained in:
parent
0af13f7063
commit
e9e79d5395
|
@ -56,7 +56,7 @@
|
|||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&emac_xfer>, <&emac_mdio>;
|
||||
phy = <&phy0>;
|
||||
phy-reset-gpios = <&gpio2 22 GPIO_ACTIVE_LOW>; /* PHY_RST */
|
||||
phy-reset-gpios = <&gpio2 RK_PC6 GPIO_ACTIVE_LOW>; /* PHY_RST */
|
||||
phy-reset-duration = <10>; /* millisecond */
|
||||
|
||||
status = "okay";
|
||||
|
|
|
@ -55,7 +55,7 @@
|
|||
compatible = "gpio-leds";
|
||||
|
||||
work {
|
||||
gpios = <&gpio2 30 GPIO_ACTIVE_HIGH>;
|
||||
gpios = <&gpio2 RK_PD6 GPIO_ACTIVE_HIGH>;
|
||||
label = "kylin:red:led";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&led_ctl>;
|
||||
|
@ -74,9 +74,9 @@
|
|||
* - SDIO_RESET_L_WL_RST
|
||||
* - SDIO_RESET_L_BT_EN
|
||||
*/
|
||||
reset-gpios = <&gpio0 26 GPIO_ACTIVE_LOW>, /* WL_REG_ON */
|
||||
<&gpio0 27 GPIO_ACTIVE_LOW>, /* WL_RST */
|
||||
<&gpio2 9 GPIO_ACTIVE_LOW>; /* BT_EN */
|
||||
reset-gpios = <&gpio0 RK_PD2 GPIO_ACTIVE_LOW>, /* WL_REG_ON */
|
||||
<&gpio0 RK_PD3 GPIO_ACTIVE_LOW>, /* WL_RST */
|
||||
<&gpio2 RK_PB1 GPIO_ACTIVE_LOW>; /* BT_EN */
|
||||
};
|
||||
|
||||
sound {
|
||||
|
@ -121,7 +121,7 @@
|
|||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&emac_xfer>, <&emac_mdio>;
|
||||
phy = <&phy0>;
|
||||
phy-reset-gpios = <&gpio2 22 GPIO_ACTIVE_LOW>; /* PHY_RST */
|
||||
phy-reset-gpios = <&gpio2 RK_PC6 GPIO_ACTIVE_LOW>; /* PHY_RST */
|
||||
phy-reset-duration = <10>; /* millisecond */
|
||||
|
||||
status = "okay";
|
||||
|
@ -148,7 +148,7 @@
|
|||
compatible = "rockchip,rk808";
|
||||
reg = <0x1b>;
|
||||
interrupt-parent = <&gpio2>;
|
||||
interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
|
||||
interrupts = <RK_PA2 IRQ_TYPE_LEVEL_LOW>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pmic_int &global_pwroff>;
|
||||
rockchip,system-power-controller;
|
||||
|
|
|
@ -71,7 +71,7 @@
|
|||
regulator-name = "sdmmc-supply";
|
||||
regulator-min-microvolt = <3000000>;
|
||||
regulator-max-microvolt = <3000000>;
|
||||
gpio = <&gpio3 7 GPIO_ACTIVE_LOW>;
|
||||
gpio = <&gpio3 RK_PA7 GPIO_ACTIVE_LOW>;
|
||||
startup-delay-us = <100000>;
|
||||
vin-supply = <&vcc_io>;
|
||||
};
|
||||
|
@ -81,7 +81,7 @@
|
|||
autorepeat;
|
||||
|
||||
power {
|
||||
gpios = <&gpio6 2 GPIO_ACTIVE_LOW>; /* GPIO6_A2 */
|
||||
gpios = <&gpio6 RK_PA2 GPIO_ACTIVE_LOW>; /* GPIO6_A2 */
|
||||
linux,code = <KEY_POWER>;
|
||||
label = "GPIO Key Power";
|
||||
linux,input-type = <1>;
|
||||
|
@ -89,7 +89,7 @@
|
|||
debounce-interval = <100>;
|
||||
};
|
||||
volume-down {
|
||||
gpios = <&gpio4 21 GPIO_ACTIVE_LOW>; /* GPIO4_C5 */
|
||||
gpios = <&gpio4 RK_PC5 GPIO_ACTIVE_LOW>; /* GPIO4_C5 */
|
||||
linux,code = <KEY_VOLUMEDOWN>;
|
||||
label = "GPIO Key Vol-";
|
||||
linux,input-type = <1>;
|
||||
|
@ -111,7 +111,7 @@
|
|||
reg = <0x2d>;
|
||||
|
||||
interrupt-parent = <&gpio6>;
|
||||
interrupts = <6 IRQ_TYPE_LEVEL_LOW>;
|
||||
interrupts = <RK_PA6 IRQ_TYPE_LEVEL_LOW>;
|
||||
|
||||
vcc5-supply = <&vcc_io>;
|
||||
vcc6-supply = <&vcc_io>;
|
||||
|
|
|
@ -69,7 +69,7 @@
|
|||
regulator-name = "sdmmc-supply";
|
||||
regulator-min-microvolt = <3000000>;
|
||||
regulator-max-microvolt = <3000000>;
|
||||
gpio = <&gpio3 7 GPIO_ACTIVE_LOW>;
|
||||
gpio = <&gpio3 RK_PA7 GPIO_ACTIVE_LOW>;
|
||||
startup-delay-us = <100000>;
|
||||
vin-supply = <&vcc_io>;
|
||||
};
|
||||
|
@ -91,7 +91,7 @@
|
|||
reg = <0x2d>;
|
||||
|
||||
interrupt-parent = <&gpio6>;
|
||||
interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
|
||||
interrupts = <RK_PA4 IRQ_TYPE_LEVEL_LOW>;
|
||||
|
||||
vcc1-supply = <&vsys>;
|
||||
vcc2-supply = <&vsys>;
|
||||
|
@ -186,7 +186,7 @@
|
|||
phy0: ethernet-phy@0 {
|
||||
reg = <0>;
|
||||
interrupt-parent = <&gpio1>;
|
||||
interrupts = <26 IRQ_TYPE_LEVEL_LOW>;
|
||||
interrupts = <RK_PD2 IRQ_TYPE_LEVEL_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
|
|
|
@ -61,7 +61,7 @@
|
|||
|
||||
blue {
|
||||
label = "mk808:blue:power";
|
||||
gpios = <&gpio0 3 GPIO_ACTIVE_HIGH>;
|
||||
gpios = <&gpio0 RK_PA3 GPIO_ACTIVE_HIGH>;
|
||||
default-state = "off";
|
||||
linux,default-trigger = "default-on";
|
||||
};
|
||||
|
@ -77,7 +77,7 @@
|
|||
vcc_host: usb-host-regulator {
|
||||
compatible = "regulator-fixed";
|
||||
enable-active-high;
|
||||
gpio = <&gpio0 6 GPIO_ACTIVE_HIGH>;
|
||||
gpio = <&gpio0 RK_PA6 GPIO_ACTIVE_HIGH>;
|
||||
pinctrl-0 = <&host_drv>;
|
||||
pinctrl-names = "default";
|
||||
regulator-always-on;
|
||||
|
@ -91,7 +91,7 @@
|
|||
vcc_otg: usb-otg-regulator {
|
||||
compatible = "regulator-fixed";
|
||||
enable-active-high;
|
||||
gpio = <&gpio0 5 GPIO_ACTIVE_HIGH>;
|
||||
gpio = <&gpio0 RK_PA5 GPIO_ACTIVE_HIGH>;
|
||||
pinctrl-0 = <&otg_drv>;
|
||||
pinctrl-names = "default";
|
||||
regulator-always-on;
|
||||
|
@ -104,7 +104,7 @@
|
|||
|
||||
vcc_sd: sdmmc-regulator {
|
||||
compatible = "regulator-fixed";
|
||||
gpio = <&gpio3 7 GPIO_ACTIVE_LOW>;
|
||||
gpio = <&gpio3 RK_PA7 GPIO_ACTIVE_LOW>;
|
||||
pinctrl-0 = <&sdmmc_pwr>;
|
||||
pinctrl-names = "default";
|
||||
regulator-name = "vcc_sd";
|
||||
|
@ -117,7 +117,7 @@
|
|||
vcc_wifi: sdio-regulator {
|
||||
compatible = "regulator-fixed";
|
||||
enable-active-high;
|
||||
gpio = <&gpio3 24 GPIO_ACTIVE_HIGH>;
|
||||
gpio = <&gpio3 RK_PD0 GPIO_ACTIVE_HIGH>;
|
||||
pinctrl-0 = <&wifi_pwr>;
|
||||
pinctrl-names = "default";
|
||||
regulator-name = "vcc_wifi";
|
||||
|
|
|
@ -55,7 +55,7 @@
|
|||
|
||||
ir: ir-receiver {
|
||||
compatible = "gpio-ir-receiver";
|
||||
gpios = <&gpio6 1 GPIO_ACTIVE_LOW>;
|
||||
gpios = <&gpio6 RK_PA1 GPIO_ACTIVE_LOW>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&ir_int>;
|
||||
};
|
||||
|
@ -65,7 +65,7 @@
|
|||
|
||||
power {
|
||||
wakeup-source;
|
||||
gpios = <&gpio6 2 GPIO_ACTIVE_LOW>;
|
||||
gpios = <&gpio6 RK_PA2 GPIO_ACTIVE_LOW>;
|
||||
label = "GPIO Power";
|
||||
linux,code = <KEY_POWER>;
|
||||
pinctrl-names = "default";
|
||||
|
@ -115,7 +115,7 @@
|
|||
vcc_sata: sata-regulator {
|
||||
compatible = "regulator-fixed";
|
||||
enable-active-high;
|
||||
gpio = <&gpio4 22 GPIO_ACTIVE_HIGH>;
|
||||
gpio = <&gpio4 RK_PC6 GPIO_ACTIVE_HIGH>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&sata_pwr>;
|
||||
regulator-name = "usb_5v";
|
||||
|
@ -127,7 +127,7 @@
|
|||
|
||||
vcc_sd: sdmmc-regulator {
|
||||
compatible = "regulator-fixed";
|
||||
gpio = <&gpio3 7 GPIO_ACTIVE_LOW>;
|
||||
gpio = <&gpio3 RK_PA7 GPIO_ACTIVE_LOW>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&sdmmc_pwr>;
|
||||
regulator-name = "vcc_sd";
|
||||
|
@ -140,7 +140,7 @@
|
|||
vcc_host: usb-host-regulator {
|
||||
compatible = "regulator-fixed";
|
||||
enable-active-high;
|
||||
gpio = <&gpio0 6 GPIO_ACTIVE_HIGH>;
|
||||
gpio = <&gpio0 RK_PA6 GPIO_ACTIVE_HIGH>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&host_drv>;
|
||||
regulator-name = "host-pwr";
|
||||
|
@ -153,7 +153,7 @@
|
|||
vcc_otg: usb-otg-regulator {
|
||||
compatible = "regulator-fixed";
|
||||
enable-active-high;
|
||||
gpio = <&gpio0 5 GPIO_ACTIVE_HIGH>;
|
||||
gpio = <&gpio0 RK_PA5 GPIO_ACTIVE_HIGH>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&otg_drv>;
|
||||
regulator-name = "vcc_otg";
|
||||
|
@ -201,7 +201,7 @@
|
|||
compatible = "asahi-kasei,ak8975";
|
||||
reg = <0x0d>;
|
||||
interrupt-parent = <&gpio4>;
|
||||
interrupts = <17 IRQ_TYPE_EDGE_RISING>;
|
||||
interrupts = <RK_PC1 IRQ_TYPE_EDGE_RISING>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&comp_int>;
|
||||
};
|
||||
|
@ -210,7 +210,7 @@
|
|||
compatible = "fsl,mma8452";
|
||||
reg = <0x1d>;
|
||||
interrupt-parent = <&gpio4>;
|
||||
interrupts = <16 IRQ_TYPE_EDGE_RISING>;
|
||||
interrupts = <RK_PC0 IRQ_TYPE_EDGE_RISING>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&gsensor_int>;
|
||||
};
|
||||
|
@ -223,7 +223,7 @@
|
|||
tps: tps@2d {
|
||||
reg = <0x2d>;
|
||||
interrupt-parent = <&gpio6>;
|
||||
interrupts = <4 IRQ_TYPE_EDGE_RISING>;
|
||||
interrupts = <RK_PA4 IRQ_TYPE_EDGE_RISING>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pmic_int>, <&pwr_hold>;
|
||||
|
||||
|
|
|
@ -62,7 +62,7 @@
|
|||
autorepeat;
|
||||
|
||||
power {
|
||||
gpios = <&gpio0 4 GPIO_ACTIVE_LOW>;
|
||||
gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_POWER>;
|
||||
label = "GPIO Key Power";
|
||||
linux,input-type = <1>;
|
||||
|
@ -102,7 +102,7 @@
|
|||
compatible = "bosch,bma250";
|
||||
reg = <0x18>;
|
||||
interrupt-parent = <&gpio0>;
|
||||
interrupts = <15 IRQ_TYPE_LEVEL_LOW>;
|
||||
interrupts = <RK_PB7 IRQ_TYPE_LEVEL_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
|
@ -114,7 +114,7 @@
|
|||
compatible = "rockchip,rk818";
|
||||
reg = <0x1c>;
|
||||
interrupt-parent = <&gpio0>;
|
||||
interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
|
||||
interrupts = <RK_PB3 IRQ_TYPE_LEVEL_LOW>;
|
||||
rockchip,system-power-controller;
|
||||
wakeup-source;
|
||||
#clock-cells = <1>;
|
||||
|
@ -247,8 +247,8 @@
|
|||
compatible = "silead,gsl1680";
|
||||
reg = <0x40>;
|
||||
interrupt-parent = <&gpio1>;
|
||||
interrupts = <15 IRQ_TYPE_EDGE_FALLING>;
|
||||
power-gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>;
|
||||
interrupts = <RK_PB7 IRQ_TYPE_EDGE_FALLING>;
|
||||
power-gpios = <&gpio0 RK_PB6 GPIO_ACTIVE_HIGH>;
|
||||
touchscreen-size-x = <800>;
|
||||
touchscreen-size-y = <1280>;
|
||||
silead,max-fingers = <5>;
|
||||
|
|
|
@ -58,7 +58,7 @@
|
|||
autorepeat;
|
||||
|
||||
power {
|
||||
gpios = <&gpio0 4 GPIO_ACTIVE_LOW>;
|
||||
gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_POWER>;
|
||||
label = "GPIO Key Power";
|
||||
linux,input-type = <1>;
|
||||
|
@ -72,19 +72,19 @@
|
|||
|
||||
green {
|
||||
label = "rock:green:user1";
|
||||
gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
|
||||
gpios = <&gpio0 RK_PB4 GPIO_ACTIVE_LOW>;
|
||||
default-state = "off";
|
||||
};
|
||||
|
||||
blue {
|
||||
label = "rock:blue:user2";
|
||||
gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
|
||||
gpios = <&gpio0 RK_PB6 GPIO_ACTIVE_LOW>;
|
||||
default-state = "off";
|
||||
};
|
||||
|
||||
sleep {
|
||||
label = "rock:red:power";
|
||||
gpios = <&gpio0 15 0>;
|
||||
gpios = <&gpio0 RK_PB7 GPIO_ACTIVE_HIGH>;
|
||||
default-state = "off";
|
||||
};
|
||||
};
|
||||
|
@ -106,7 +106,7 @@
|
|||
|
||||
ir_recv: gpio-ir-receiver {
|
||||
compatible = "gpio-ir-receiver";
|
||||
gpios = <&gpio0 10 1>;
|
||||
gpios = <&gpio0 RK_PB2 GPIO_ACTIVE_LOW>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&ir_recv_pin>;
|
||||
};
|
||||
|
@ -114,7 +114,7 @@
|
|||
vcc_otg: usb-otg-regulator {
|
||||
compatible = "regulator-fixed";
|
||||
enable-active-high;
|
||||
gpio = <&gpio2 31 GPIO_ACTIVE_HIGH>;
|
||||
gpio = <&gpio2 RK_PD7 GPIO_ACTIVE_HIGH>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&otg_vbus_drv>;
|
||||
regulator-name = "otg-vbus";
|
||||
|
@ -129,7 +129,7 @@
|
|||
regulator-name = "sdmmc-supply";
|
||||
regulator-min-microvolt = <3300000>;
|
||||
regulator-max-microvolt = <3300000>;
|
||||
gpio = <&gpio3 1 GPIO_ACTIVE_LOW>;
|
||||
gpio = <&gpio3 RK_PA1 GPIO_ACTIVE_LOW>;
|
||||
startup-delay-us = <100000>;
|
||||
vin-supply = <&vcc_io>;
|
||||
};
|
||||
|
@ -137,7 +137,7 @@
|
|||
vcc_host: usb-host-regulator {
|
||||
compatible = "regulator-fixed";
|
||||
enable-active-high;
|
||||
gpio = <&gpio0 3 GPIO_ACTIVE_HIGH>;
|
||||
gpio = <&gpio0 RK_PA3 GPIO_ACTIVE_HIGH>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&host_vbus_drv>;
|
||||
regulator-name = "host-pwr";
|
||||
|
@ -168,7 +168,7 @@
|
|||
phy0: ethernet-phy@0 {
|
||||
reg = <0>;
|
||||
interrupt-parent = <&gpio3>;
|
||||
interrupts = <26 IRQ_TYPE_LEVEL_LOW>;
|
||||
interrupts = <RK_PD2 IRQ_TYPE_LEVEL_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
|
@ -184,7 +184,7 @@
|
|||
compatible = "haoyu,hym8563";
|
||||
reg = <0x51>;
|
||||
interrupt-parent = <&gpio0>;
|
||||
interrupts = <13 IRQ_TYPE_EDGE_FALLING>;
|
||||
interrupts = <RK_PB5 IRQ_TYPE_EDGE_FALLING>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&rtc_int>;
|
||||
#clock-cells = <0>;
|
||||
|
|
|
@ -77,7 +77,7 @@
|
|||
phy-mode = "rgmii";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&rgmii_pins>;
|
||||
snps,reset-gpio = <&gpio2 24 GPIO_ACTIVE_LOW>;
|
||||
snps,reset-gpio = <&gpio2 RK_PD0 GPIO_ACTIVE_LOW>;
|
||||
snps,reset-active-low;
|
||||
snps,reset-delays-us = <0 10000 1000000>;
|
||||
tx_delay = <0x30>;
|
||||
|
|
|
@ -47,7 +47,7 @@
|
|||
vcc_lcd: vcc-lcd {
|
||||
compatible = "regulator-fixed";
|
||||
enable-active-high;
|
||||
gpio = <&gpio7 3 GPIO_ACTIVE_HIGH>;
|
||||
gpio = <&gpio7 RK_PA3 GPIO_ACTIVE_HIGH>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&lcd_en>;
|
||||
regulator-name = "vcc_lcd";
|
||||
|
@ -57,7 +57,7 @@
|
|||
vcc_wl: vcc-wl {
|
||||
compatible = "regulator-fixed";
|
||||
enable-active-high;
|
||||
gpio = <&gpio7 9 GPIO_ACTIVE_HIGH>;
|
||||
gpio = <&gpio7 RK_PB1 GPIO_ACTIVE_HIGH>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&wifi_pwr>;
|
||||
regulator-name = "vcc_wl";
|
||||
|
@ -96,7 +96,7 @@
|
|||
reg = <0x51>;
|
||||
|
||||
interrupt-parent = <&gpio0>;
|
||||
interrupts = <4 IRQ_TYPE_EDGE_FALLING>;
|
||||
interrupts = <RK_PA4 IRQ_TYPE_EDGE_FALLING>;
|
||||
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pmic_int>;
|
||||
|
|
|
@ -52,7 +52,7 @@
|
|||
compatible = "rockchip,rk808";
|
||||
reg = <0x1b>;
|
||||
interrupt-parent = <&gpio0>;
|
||||
interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
|
||||
interrupts = <RK_PA4 IRQ_TYPE_LEVEL_LOW>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pmic_int &global_pwroff>;
|
||||
rockchip,system-power-controller;
|
||||
|
|
|
@ -84,7 +84,7 @@
|
|||
240 241 242 243 244 245 246 247
|
||||
248 249 250 251 252 253 254 255>;
|
||||
default-brightness-level = <128>;
|
||||
enable-gpios = <&gpio7 2 GPIO_ACTIVE_HIGH>;
|
||||
enable-gpios = <&gpio7 RK_PA2 GPIO_ACTIVE_HIGH>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&bl_en>;
|
||||
pwms = <&pwm0 0 1000000 PWM_POLARITY_INVERTED>;
|
||||
|
@ -100,7 +100,7 @@
|
|||
panel: panel {
|
||||
compatible ="lg,lp079qx1-sp0v", "simple-panel";
|
||||
backlight = <&backlight>;
|
||||
enable-gpios = <&gpio7 4 GPIO_ACTIVE_HIGH>;
|
||||
enable-gpios = <&gpio7 RK_PA4 GPIO_ACTIVE_HIGH>;
|
||||
pinctrl-0 = <&lcd_cs>;
|
||||
|
||||
ports {
|
||||
|
@ -120,7 +120,7 @@
|
|||
pinctrl-0 = <&pwrbtn>;
|
||||
|
||||
power {
|
||||
gpios = <&gpio0 5 GPIO_ACTIVE_LOW>;
|
||||
gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_POWER>;
|
||||
label = "GPIO Key Power";
|
||||
linux,input-type = <1>;
|
||||
|
@ -133,7 +133,7 @@
|
|||
vcc_host: vcc-host-regulator {
|
||||
compatible = "regulator-fixed";
|
||||
enable-active-high;
|
||||
gpio = <&gpio0 14 GPIO_ACTIVE_HIGH>;
|
||||
gpio = <&gpio0 RK_PB6 GPIO_ACTIVE_HIGH>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&host_vbus_drv>;
|
||||
regulator-name = "vcc_host";
|
||||
|
@ -144,7 +144,7 @@
|
|||
vcc_phy: vcc-phy-regulator {
|
||||
compatible = "regulator-fixed";
|
||||
enable-active-high;
|
||||
gpio = <&gpio0 6 GPIO_ACTIVE_HIGH>;
|
||||
gpio = <&gpio0 RK_PA6 GPIO_ACTIVE_HIGH>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <ð_phy_pwr>;
|
||||
regulator-name = "vcc_phy";
|
||||
|
@ -170,7 +170,7 @@
|
|||
*/
|
||||
vcc_sd: sdmmc-regulator {
|
||||
compatible = "regulator-fixed";
|
||||
gpio = <&gpio7 11 GPIO_ACTIVE_LOW>;
|
||||
gpio = <&gpio7 RK_PB3 GPIO_ACTIVE_LOW>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&sdmmc_pwr>;
|
||||
regulator-name = "vcc_sd";
|
||||
|
@ -236,7 +236,7 @@
|
|||
phy-supply = <&vcc_phy>;
|
||||
phy-mode = "rgmii";
|
||||
clock_in_out = "input";
|
||||
snps,reset-gpio = <&gpio4 7 0>;
|
||||
snps,reset-gpio = <&gpio4 RK_PA7 GPIO_ACTIVE_HIGH>;
|
||||
snps,reset-active-low;
|
||||
snps,reset-delays-us = <0 10000 1000000>;
|
||||
assigned-clocks = <&cru SCLK_MAC>;
|
||||
|
|
|
@ -93,7 +93,7 @@
|
|||
phy-mode = "rgmii";
|
||||
snps,reset-active-low;
|
||||
snps,reset-delays-us = <0 10000 1000000>;
|
||||
snps,reset-gpio = <&gpio4 8 GPIO_ACTIVE_LOW>;
|
||||
snps,reset-gpio = <&gpio4 RK_PB0 GPIO_ACTIVE_LOW>;
|
||||
tx_delay = <0x30>;
|
||||
rx_delay = <0x10>;
|
||||
status = "okay";
|
||||
|
@ -111,7 +111,7 @@
|
|||
compatible = "rockchip,rk808";
|
||||
reg = <0x1b>;
|
||||
interrupt-parent = <&gpio0>;
|
||||
interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
|
||||
interrupts = <RK_PA4 IRQ_TYPE_LEVEL_LOW>;
|
||||
#clock-cells = <1>;
|
||||
clock-output-names = "xin32k", "rk808-clkout2";
|
||||
pinctrl-names = "default";
|
||||
|
@ -345,7 +345,7 @@
|
|||
&usbphy {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&host_drv>;
|
||||
vbus_drv-gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>;
|
||||
vbus_drv-gpios = <&gpio0 RK_PB6 GPIO_ACTIVE_HIGH>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
|
|
|
@ -49,7 +49,7 @@
|
|||
};
|
||||
|
||||
&ir {
|
||||
gpios = <&gpio7 5 GPIO_ACTIVE_LOW>;
|
||||
gpios = <&gpio7 RK_PA5 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
&pinctrl {
|
||||
|
|
|
@ -96,7 +96,7 @@
|
|||
phy-mode = "rgmii";
|
||||
snps,reset-active-low;
|
||||
snps,reset-delays-us = <0 10000 1000000>;
|
||||
snps,reset-gpio = <&gpio4 8 GPIO_ACTIVE_LOW>;
|
||||
snps,reset-gpio = <&gpio4 RK_PB0 GPIO_ACTIVE_LOW>;
|
||||
tx_delay = <0x30>;
|
||||
rx_delay = <0x10>;
|
||||
status = "ok";
|
||||
|
|
|
@ -53,7 +53,7 @@
|
|||
|
||||
power {
|
||||
wakeup-source;
|
||||
gpios = <&gpio0 5 GPIO_ACTIVE_LOW>;
|
||||
gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>;
|
||||
label = "GPIO Power";
|
||||
linux,code = <KEY_POWER>;
|
||||
pinctrl-names = "default";
|
||||
|
@ -63,14 +63,14 @@
|
|||
|
||||
ir-receiver {
|
||||
compatible = "gpio-ir-receiver";
|
||||
gpios = <&gpio7 0 GPIO_ACTIVE_LOW>;
|
||||
gpios = <&gpio7 RK_PA0 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
power {
|
||||
gpios = <&gpio8 2 GPIO_ACTIVE_LOW>;
|
||||
gpios = <&gpio8 RK_PA2 GPIO_ACTIVE_LOW>;
|
||||
label = "firefly:blue:power";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&power_led>;
|
||||
|
@ -78,7 +78,7 @@
|
|||
};
|
||||
|
||||
work {
|
||||
gpios = <&gpio8 1 GPIO_ACTIVE_LOW>;
|
||||
gpios = <&gpio8 RK_PA1 GPIO_ACTIVE_LOW>;
|
||||
label = "firefly:blue:user";
|
||||
linux,default-trigger = "rc-feedback";
|
||||
pinctrl-names = "default";
|
||||
|
@ -92,7 +92,7 @@
|
|||
clock-names = "ext_clock";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&wifi_enable>;
|
||||
reset-gpios = <&gpio4 28 GPIO_ACTIVE_LOW>;
|
||||
reset-gpios = <&gpio4 RK_PD4 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
sound {
|
||||
|
@ -112,7 +112,7 @@
|
|||
vcc_host_5v: usb-host-regulator {
|
||||
compatible = "regulator-fixed";
|
||||
enable-active-high;
|
||||
gpio = <&gpio0 14 GPIO_ACTIVE_HIGH>;
|
||||
gpio = <&gpio0 RK_PB6 GPIO_ACTIVE_HIGH>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&host_vbus_drv>;
|
||||
regulator-name = "vcc_host_5v";
|
||||
|
@ -133,7 +133,7 @@
|
|||
|
||||
vcc_sd: sdmmc-regulator {
|
||||
compatible = "regulator-fixed";
|
||||
gpio = <&gpio7 11 GPIO_ACTIVE_LOW>;
|
||||
gpio = <&gpio7 RK_PB3 GPIO_ACTIVE_LOW>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&sdmmc_pwr>;
|
||||
regulator-name = "vcc_sd";
|
||||
|
@ -146,7 +146,7 @@
|
|||
vcc_otg_5v: usb-otg-regulator {
|
||||
compatible = "regulator-fixed";
|
||||
enable-active-high;
|
||||
gpio = <&gpio0 12 GPIO_ACTIVE_HIGH>;
|
||||
gpio = <&gpio0 RK_PB4 GPIO_ACTIVE_HIGH>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&otg_vbus_drv>;
|
||||
regulator-name = "vcc_otg_5v";
|
||||
|
@ -159,7 +159,7 @@
|
|||
dovdd_1v8: dovdd-1v8-regulator {
|
||||
compatible = "regulator-fixed";
|
||||
enable-active-high;
|
||||
gpio = <&gpio0 11 GPIO_ACTIVE_HIGH>;
|
||||
gpio = <&gpio0 RK_PB3 GPIO_ACTIVE_HIGH>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&dvp_pwr>;
|
||||
regulator-name = "dovdd_1v8";
|
||||
|
@ -171,7 +171,7 @@
|
|||
vcc28_dvp: vcc28-dvp-regulator {
|
||||
compatible = "regulator-fixed";
|
||||
enable-active-high;
|
||||
gpio = <&gpio0 11 GPIO_ACTIVE_HIGH>;
|
||||
gpio = <&gpio0 RK_PB3 GPIO_ACTIVE_HIGH>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&dvp_pwr>;
|
||||
regulator-name = "vcc28_dvp";
|
||||
|
@ -183,7 +183,7 @@
|
|||
af_28: af_28-regulator {
|
||||
compatible = "regulator-fixed";
|
||||
enable-active-high;
|
||||
gpio = <&gpio0 11 GPIO_ACTIVE_HIGH>;
|
||||
gpio = <&gpio0 RK_PB3 GPIO_ACTIVE_HIGH>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&dvp_pwr>;
|
||||
regulator-name = "af_28";
|
||||
|
@ -195,7 +195,7 @@
|
|||
dvdd_1v2: af_28-regulator {
|
||||
compatible = "regulator-fixed";
|
||||
enable-active-high;
|
||||
gpio = <&gpio7 12 GPIO_ACTIVE_HIGH>;
|
||||
gpio = <&gpio7 RK_PB4 GPIO_ACTIVE_HIGH>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&cif_pwr>;
|
||||
regulator-name = "dvdd_1v2";
|
||||
|
@ -221,7 +221,7 @@
|
|||
clock-frequency = <32768>;
|
||||
clock-output-names = "xin32k";
|
||||
interrupt-parent = <&gpio7>;
|
||||
interrupts = <4 IRQ_TYPE_EDGE_FALLING>;
|
||||
interrupts = <RK_PA4 IRQ_TYPE_EDGE_FALLING>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&rtc_int>;
|
||||
};
|
||||
|
|
|
@ -49,7 +49,7 @@
|
|||
};
|
||||
|
||||
&ir {
|
||||
gpios = <&gpio7 0 GPIO_ACTIVE_LOW>;
|
||||
gpios = <&gpio7 RK_PA0 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
&pinctrl {
|
||||
|
|
|
@ -75,7 +75,7 @@
|
|||
|
||||
power {
|
||||
wakeup-source;
|
||||
gpios = <&gpio0 5 GPIO_ACTIVE_LOW>;
|
||||
gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>;
|
||||
label = "GPIO Power";
|
||||
linux,code = <KEY_POWER>;
|
||||
pinctrl-names = "default";
|
||||
|
@ -87,7 +87,7 @@
|
|||
compatible = "gpio-leds";
|
||||
|
||||
work {
|
||||
gpios = <&gpio8 1 GPIO_ACTIVE_LOW>;
|
||||
gpios = <&gpio8 RK_PA1 GPIO_ACTIVE_LOW>;
|
||||
label = "firefly:blue:user";
|
||||
linux,default-trigger = "rc-feedback";
|
||||
pinctrl-names = "default";
|
||||
|
@ -95,7 +95,7 @@
|
|||
};
|
||||
|
||||
power {
|
||||
gpios = <&gpio8 2 GPIO_ACTIVE_LOW>;
|
||||
gpios = <&gpio8 RK_PA2 GPIO_ACTIVE_LOW>;
|
||||
label = "firefly:green:power";
|
||||
linux,default-trigger = "default-on";
|
||||
pinctrl-names = "default";
|
||||
|
@ -114,7 +114,7 @@
|
|||
|
||||
vcc_sd: sdmmc-regulator {
|
||||
compatible = "regulator-fixed";
|
||||
gpio = <&gpio7 11 GPIO_ACTIVE_LOW>;
|
||||
gpio = <&gpio7 RK_PB3 GPIO_ACTIVE_LOW>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&sdmmc_pwr>;
|
||||
regulator-name = "vcc_sd";
|
||||
|
@ -145,7 +145,7 @@
|
|||
vcc_host_5v: usb-host-regulator {
|
||||
compatible = "regulator-fixed";
|
||||
enable-active-high;
|
||||
gpio = <&gpio0 14 GPIO_ACTIVE_HIGH>;
|
||||
gpio = <&gpio0 RK_PB6 GPIO_ACTIVE_HIGH>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&host_vbus_drv>;
|
||||
regulator-name = "vcc_host_5v";
|
||||
|
@ -158,7 +158,7 @@
|
|||
vcc_otg_5v: usb-otg-regulator {
|
||||
compatible = "regulator-fixed";
|
||||
enable-active-high;
|
||||
gpio = <&gpio0 12 GPIO_ACTIVE_HIGH>;
|
||||
gpio = <&gpio0 RK_PB4 GPIO_ACTIVE_HIGH>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&otg_vbus_drv>;
|
||||
regulator-name = "vcc_otg_5v";
|
||||
|
@ -175,7 +175,7 @@
|
|||
vcc28_dvp: vcc28-dvp-regulator {
|
||||
compatible = "regulator-fixed";
|
||||
enable-active-high;
|
||||
gpio = <&gpio0 11 GPIO_ACTIVE_HIGH>;
|
||||
gpio = <&gpio0 RK_PB3 GPIO_ACTIVE_HIGH>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&dvp_pwr>;
|
||||
regulator-name = "vcc28_dvp";
|
||||
|
@ -213,7 +213,7 @@
|
|||
phy-mode = "rgmii";
|
||||
snps,reset-active-low;
|
||||
snps,reset-delays-us = <0 10000 1000000>;
|
||||
snps,reset-gpio = <&gpio4 8 GPIO_ACTIVE_LOW>;
|
||||
snps,reset-gpio = <&gpio4 RK_PB0 GPIO_ACTIVE_LOW>;
|
||||
tx_delay = <0x30>;
|
||||
rx_delay = <0x10>;
|
||||
status = "ok";
|
||||
|
@ -260,7 +260,7 @@
|
|||
clock-frequency = <32768>;
|
||||
clock-output-names = "xin32k";
|
||||
interrupt-parent = <&gpio7>;
|
||||
interrupts = <4 IRQ_TYPE_EDGE_FALLING>;
|
||||
interrupts = <RK_PA4 IRQ_TYPE_EDGE_FALLING>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&rtc_int>;
|
||||
};
|
||||
|
|
|
@ -68,7 +68,7 @@
|
|||
compatible = "gpio-leds";
|
||||
|
||||
work {
|
||||
gpios = <&gpio7 4 GPIO_ACTIVE_LOW>;
|
||||
gpios = <&gpio7 RK_PA4 GPIO_ACTIVE_LOW>;
|
||||
label = "miqi:green:user";
|
||||
linux,default-trigger = "default-on";
|
||||
pinctrl-names = "default";
|
||||
|
@ -87,7 +87,7 @@
|
|||
vcc_host: usb-host-regulator {
|
||||
compatible = "regulator-fixed";
|
||||
enable-active-high;
|
||||
gpio = <&gpio0 14 GPIO_ACTIVE_HIGH>;
|
||||
gpio = <&gpio0 RK_PB6 GPIO_ACTIVE_HIGH>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&host_vbus_drv>;
|
||||
regulator-name = "vcc_host";
|
||||
|
@ -99,7 +99,7 @@
|
|||
|
||||
vcc_sd: sdmmc-regulator {
|
||||
compatible = "regulator-fixed";
|
||||
gpio = <&gpio7 11 GPIO_ACTIVE_LOW>;
|
||||
gpio = <&gpio7 RK_PB3 GPIO_ACTIVE_LOW>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&sdmmc_pwr>;
|
||||
regulator-name = "vcc_sd";
|
||||
|
@ -146,7 +146,7 @@
|
|||
phy-mode = "rgmii";
|
||||
snps,reset-active-low;
|
||||
snps,reset-delays-us = <0 10000 1000000>;
|
||||
snps,reset-gpio = <&gpio4 8 GPIO_ACTIVE_LOW>;
|
||||
snps,reset-gpio = <&gpio4 RK_PB0 GPIO_ACTIVE_LOW>;
|
||||
tx_delay = <0x30>;
|
||||
rx_delay = <0x10>;
|
||||
status = "ok";
|
||||
|
|
|
@ -180,7 +180,7 @@
|
|||
phy-supply = <&vcc_lan>;
|
||||
phy-mode = "rgmii";
|
||||
clock_in_out = "input";
|
||||
snps,reset-gpio = <&gpio4 RK_PB0 0>;
|
||||
snps,reset-gpio = <&gpio4 RK_PB0 GPIO_ACTIVE_HIGH>;
|
||||
snps,reset-active-low;
|
||||
snps,reset-delays-us = <0 10000 1000000>;
|
||||
assigned-clocks = <&cru SCLK_MAC>;
|
||||
|
@ -205,7 +205,7 @@
|
|||
compatible = "rockchip,rk808";
|
||||
reg = <0x1b>;
|
||||
interrupt-parent = <&gpio0>;
|
||||
interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
|
||||
interrupts = <RK_PA4 IRQ_TYPE_LEVEL_LOW>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pmic_int &global_pwroff>;
|
||||
rockchip,system-power-controller;
|
||||
|
@ -390,7 +390,7 @@
|
|||
compatible = "asahi-kasei,ak8975";
|
||||
reg = <0x0d>;
|
||||
interrupt-parent = <&gpio8>;
|
||||
interrupts = <1 IRQ_TYPE_EDGE_RISING>;
|
||||
interrupts = <RK_PA1 IRQ_TYPE_EDGE_RISING>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&comp_int>;
|
||||
vdd-supply = <&vcc_io>;
|
||||
|
@ -409,7 +409,7 @@
|
|||
compatible = "fsl,mma8452";
|
||||
reg = <0x1d>;
|
||||
interrupt-parent = <&gpio8>;
|
||||
interrupts = <0 IRQ_TYPE_EDGE_RISING>;
|
||||
interrupts = <RK_PA0 IRQ_TYPE_EDGE_RISING>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&gsensor_int>;
|
||||
};
|
||||
|
|
|
@ -68,7 +68,7 @@
|
|||
pinctrl-0 = <&pwrbtn>;
|
||||
|
||||
power {
|
||||
gpios = <&gpio0 5 GPIO_ACTIVE_LOW>;
|
||||
gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_POWER>;
|
||||
label = "GPIO Key Power";
|
||||
linux,input-type = <1>;
|
||||
|
@ -79,7 +79,7 @@
|
|||
|
||||
ir: ir-receiver {
|
||||
compatible = "gpio-ir-receiver";
|
||||
gpios = <&gpio7 0 GPIO_ACTIVE_LOW>;
|
||||
gpios = <&gpio7 RK_PA0 GPIO_ACTIVE_LOW>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&ir_int>;
|
||||
};
|
||||
|
@ -87,7 +87,7 @@
|
|||
vcc_host: vcc-host-regulator {
|
||||
compatible = "regulator-fixed";
|
||||
enable-active-high;
|
||||
gpio = <&gpio0 14 GPIO_ACTIVE_HIGH>;
|
||||
gpio = <&gpio0 RK_PB6 GPIO_ACTIVE_HIGH>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&host_vbus_drv>;
|
||||
regulator-name = "vcc_host";
|
||||
|
@ -98,7 +98,7 @@
|
|||
vcc_otg: vcc-otg-regulator {
|
||||
compatible = "regulator-fixed";
|
||||
enable-active-high;
|
||||
gpio = <&gpio0 12 GPIO_ACTIVE_HIGH>;
|
||||
gpio = <&gpio0 RK_PB4 GPIO_ACTIVE_HIGH>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&otg_vbus_drv>;
|
||||
regulator-name = "vcc_otg";
|
||||
|
@ -111,7 +111,7 @@
|
|||
regulator-name = "sdmmc-supply";
|
||||
regulator-min-microvolt = <3300000>;
|
||||
regulator-max-microvolt = <3300000>;
|
||||
gpio = <&gpio7 11 GPIO_ACTIVE_LOW>;
|
||||
gpio = <&gpio7 RK_PB3 GPIO_ACTIVE_LOW>;
|
||||
startup-delay-us = <100000>;
|
||||
vin-supply = <&vcc_io>;
|
||||
};
|
||||
|
@ -134,7 +134,7 @@
|
|||
phy-supply = <&vcc_lan>;
|
||||
phy-mode = "rgmii";
|
||||
clock_in_out = "input";
|
||||
snps,reset-gpio = <&gpio4 7 0>;
|
||||
snps,reset-gpio = <&gpio4 RK_PA7 GPIO_ACTIVE_HIGH>;
|
||||
snps,reset-active-low;
|
||||
snps,reset-delays-us = <0 10000 1000000>;
|
||||
assigned-clocks = <&cru SCLK_MAC>;
|
||||
|
@ -187,7 +187,7 @@
|
|||
#clock-cells = <0>;
|
||||
clock-output-names = "xin32k";
|
||||
interrupt-parent = <&gpio0>;
|
||||
interrupts = <4 IRQ_TYPE_EDGE_FALLING>;
|
||||
interrupts = <RK_PA4 IRQ_TYPE_EDGE_FALLING>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pmic_int>;
|
||||
};
|
||||
|
|
|
@ -51,7 +51,7 @@
|
|||
compatible = "mmc-pwrseq-emmc";
|
||||
pinctrl-0 = <&emmc_reset>;
|
||||
pinctrl-names = "default";
|
||||
reset-gpios = <&gpio3 9 GPIO_ACTIVE_LOW>;
|
||||
reset-gpios = <&gpio3 RK_PB1 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
ext_gmac: external-gmac-clock {
|
||||
|
@ -106,7 +106,7 @@
|
|||
phy-supply = <&vccio_pmu>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&rgmii_pins &phy_rst>;
|
||||
snps,reset-gpio = <&gpio4 8 GPIO_ACTIVE_LOW>;
|
||||
snps,reset-gpio = <&gpio4 RK_PB0 GPIO_ACTIVE_LOW>;
|
||||
snps,reset-active-low;
|
||||
snps,reset-delays-us = <0 10000 30000>;
|
||||
rx_delay = <0x10>;
|
||||
|
|
|
@ -53,13 +53,13 @@
|
|||
compatible = "gpio-leds";
|
||||
|
||||
heartbeat {
|
||||
gpios = <&gpio7 15 GPIO_ACTIVE_LOW>;
|
||||
gpios = <&gpio7 RK_PB7 GPIO_ACTIVE_LOW>;
|
||||
label = "rock2:green:state1";
|
||||
linux,default-trigger = "heartbeat";
|
||||
};
|
||||
|
||||
mmc {
|
||||
gpios = <&gpio0 11 GPIO_ACTIVE_LOW>;
|
||||
gpios = <&gpio0 RK_PB3 GPIO_ACTIVE_LOW>;
|
||||
label = "rock2:blue:state2";
|
||||
linux,default-trigger = "mmc0";
|
||||
};
|
||||
|
@ -67,7 +67,7 @@
|
|||
|
||||
ir: ir-receiver {
|
||||
compatible = "gpio-ir-receiver";
|
||||
gpios = <&gpio8 1 GPIO_ACTIVE_LOW>;
|
||||
gpios = <&gpio8 RK_PA1 GPIO_ACTIVE_LOW>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&ir_int>;
|
||||
};
|
||||
|
@ -92,13 +92,13 @@
|
|||
clock-names = "ext_clock";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&wifi_enable>;
|
||||
reset-gpios = <&gpio4 28 GPIO_ACTIVE_LOW>;
|
||||
reset-gpios = <&gpio4 RK_PD4 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
vcc_usb_host: vcc-host-regulator {
|
||||
compatible = "regulator-fixed";
|
||||
enable-active-high;
|
||||
gpio = <&gpio0 14 GPIO_ACTIVE_HIGH>;
|
||||
gpio = <&gpio0 RK_PB6 GPIO_ACTIVE_HIGH>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&host_vbus_drv>;
|
||||
/* Always on as the rockchip usb phy doesn't have a vbus-supply
|
||||
|
@ -110,7 +110,7 @@
|
|||
|
||||
vcc_sd: sdmmc-regulator {
|
||||
compatible = "regulator-fixed";
|
||||
gpio = <&gpio7 11 GPIO_ACTIVE_LOW>;
|
||||
gpio = <&gpio7 RK_PB3 GPIO_ACTIVE_LOW>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&sdmmc_pwr>;
|
||||
regulator-name = "vcc_sd";
|
||||
|
@ -166,7 +166,7 @@
|
|||
clock-frequency = <32768>;
|
||||
clock-output-names = "xin32k";
|
||||
interrupt-parent = <&gpio0>;
|
||||
interrupts = <4 IRQ_TYPE_EDGE_FALLING>;
|
||||
interrupts = <RK_PA4 IRQ_TYPE_EDGE_FALLING>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pmic_int>;
|
||||
|
||||
|
|
|
@ -17,8 +17,8 @@
|
|||
rockchip,model = "VEYRON-I2S";
|
||||
rockchip,i2s-controller = <&i2s>;
|
||||
rockchip,audio-codec = <&max98090>;
|
||||
rockchip,hp-det-gpios = <&gpio6 5 GPIO_ACTIVE_HIGH>;
|
||||
rockchip,mic-det-gpios = <&gpio6 11 GPIO_ACTIVE_LOW>;
|
||||
rockchip,hp-det-gpios = <&gpio6 RK_PA5 GPIO_ACTIVE_HIGH>;
|
||||
rockchip,mic-det-gpios = <&gpio6 RK_PB3 GPIO_ACTIVE_LOW>;
|
||||
rockchip,headset-codec = <&headsetcodec>;
|
||||
};
|
||||
};
|
||||
|
@ -28,7 +28,7 @@
|
|||
compatible = "maxim,max98090";
|
||||
reg = <0x10>;
|
||||
interrupt-parent = <&gpio6>;
|
||||
interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
|
||||
interrupts = <RK_PA7 IRQ_TYPE_EDGE_FALLING>;
|
||||
clock-names = "mclk";
|
||||
clocks = <&cru SCLK_I2S0_OUT>;
|
||||
pinctrl-names = "default";
|
||||
|
@ -41,7 +41,7 @@
|
|||
compatible = "ti,ts3a227e";
|
||||
reg = <0x3b>;
|
||||
interrupt-parent = <&gpio0>;
|
||||
interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
|
||||
interrupts = <RK_PA3 IRQ_TYPE_LEVEL_LOW>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&ts3a227e_int_l>;
|
||||
ti,micbias = <7>; /* MICBIAS = 2.8V */
|
||||
|
|
|
@ -67,7 +67,7 @@
|
|||
vcc5_host2: vcc5-host2-regulator {
|
||||
compatible = "regulator-fixed";
|
||||
enable-active-high;
|
||||
gpio = <&gpio0 12 GPIO_ACTIVE_HIGH>;
|
||||
gpio = <&gpio0 RK_PB4 GPIO_ACTIVE_HIGH>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&usb2_pwr_en>;
|
||||
regulator-name = "vcc5_host2";
|
||||
|
@ -103,8 +103,8 @@
|
|||
&rk808 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pmic_int_l &dvs_1 &dvs_2>;
|
||||
dvs-gpios = <&gpio7 11 GPIO_ACTIVE_HIGH>,
|
||||
<&gpio7 15 GPIO_ACTIVE_HIGH>;
|
||||
dvs-gpios = <&gpio7 RK_PB3 GPIO_ACTIVE_HIGH>,
|
||||
<&gpio7 RK_PB7 GPIO_ACTIVE_HIGH>;
|
||||
|
||||
/delete-property/ vcc6-supply;
|
||||
|
||||
|
@ -133,7 +133,7 @@
|
|||
|
||||
&vcc50_hdmi {
|
||||
enable-active-high;
|
||||
gpio = <&gpio7 2 GPIO_ACTIVE_HIGH>;
|
||||
gpio = <&gpio7 RK_PA2 GPIO_ACTIVE_HIGH>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&vcc50_hdmi_en>;
|
||||
};
|
||||
|
|
|
@ -91,7 +91,7 @@
|
|||
240 241 242 243 244 245 246 247
|
||||
248 249 250 251 252 253 254 255>;
|
||||
default-brightness-level = <128>;
|
||||
enable-gpios = <&gpio7 2 GPIO_ACTIVE_HIGH>;
|
||||
enable-gpios = <&gpio7 RK_PA2 GPIO_ACTIVE_HIGH>;
|
||||
backlight-boot-off;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&bl_en>;
|
||||
|
@ -102,7 +102,7 @@
|
|||
gpio-charger {
|
||||
compatible = "gpio-charger";
|
||||
charger-type = "mains";
|
||||
gpios = <&gpio0 8 GPIO_ACTIVE_HIGH>;
|
||||
gpios = <&gpio0 RK_PB0 GPIO_ACTIVE_HIGH>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&ac_present_ap>;
|
||||
};
|
||||
|
@ -142,7 +142,7 @@
|
|||
vcc5_host1: vcc5-host1-regulator {
|
||||
compatible = "regulator-fixed";
|
||||
enable-active-high;
|
||||
gpio = <&gpio0 11 GPIO_ACTIVE_HIGH>;
|
||||
gpio = <&gpio0 RK_PB3 GPIO_ACTIVE_HIGH>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&host1_pwr_en>;
|
||||
regulator-name = "vcc5_host1";
|
||||
|
@ -154,7 +154,7 @@
|
|||
vcc5v_otg: vcc5v-otg-regulator {
|
||||
compatible = "regulator-fixed";
|
||||
enable-active-high;
|
||||
gpio = <&gpio0 12 GPIO_ACTIVE_HIGH>;
|
||||
gpio = <&gpio0 RK_PB4 GPIO_ACTIVE_HIGH>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&usbotg_pwren_h>;
|
||||
regulator-name = "vcc5_host2";
|
||||
|
@ -190,7 +190,7 @@
|
|||
pinctrl-0 = <&pwr_key_l &ap_lid_int_l>;
|
||||
lid {
|
||||
label = "Lid";
|
||||
gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
|
||||
gpios = <&gpio0 RK_PA6 GPIO_ACTIVE_LOW>;
|
||||
wakeup-source;
|
||||
linux,code = <0>; /* SW_LID */
|
||||
linux,input-type = <5>; /* EV_SW */
|
||||
|
@ -228,7 +228,7 @@
|
|||
reg = <0>;
|
||||
google,cros-ec-spi-pre-delay = <30>;
|
||||
interrupt-parent = <&gpio7>;
|
||||
interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
|
||||
interrupts = <RK_PA7 IRQ_TYPE_LEVEL_LOW>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&ec_int>;
|
||||
spi-max-frequency = <3000000>;
|
||||
|
@ -247,7 +247,7 @@
|
|||
compatible = "elan,ekth3000";
|
||||
reg = <0x15>;
|
||||
interrupt-parent = <&gpio7>;
|
||||
interrupts = <3 IRQ_TYPE_EDGE_FALLING>;
|
||||
interrupts = <RK_PA3 IRQ_TYPE_EDGE_FALLING>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&trackpad_int>;
|
||||
vcc-supply = <&vcc33_io>;
|
||||
|
|
|
@ -57,7 +57,7 @@
|
|||
panel_regulator: panel-regulator {
|
||||
compatible = "regulator-fixed";
|
||||
enable-active-high;
|
||||
gpio = <&gpio7 14 GPIO_ACTIVE_HIGH>;
|
||||
gpio = <&gpio7 RK_PB6 GPIO_ACTIVE_HIGH>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&lcd_enable_h>;
|
||||
regulator-name = "panel_regulator";
|
||||
|
@ -68,7 +68,7 @@
|
|||
vcc18_lcd: vcc18-lcd {
|
||||
compatible = "regulator-fixed";
|
||||
enable-active-high;
|
||||
gpio = <&gpio2 13 GPIO_ACTIVE_HIGH>;
|
||||
gpio = <&gpio2 RK_PB5 GPIO_ACTIVE_HIGH>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&avdd_1v8_disp_en>;
|
||||
regulator-name = "vcc18_lcd";
|
||||
|
@ -80,7 +80,7 @@
|
|||
backlight_regulator: backlight-regulator {
|
||||
compatible = "regulator-fixed";
|
||||
enable-active-high;
|
||||
gpio = <&gpio2 12 GPIO_ACTIVE_HIGH>;
|
||||
gpio = <&gpio2 RK_PB4 GPIO_ACTIVE_HIGH>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&bl_pwr_en>;
|
||||
regulator-name = "backlight_regulator";
|
||||
|
@ -134,8 +134,8 @@
|
|||
&rk808 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pmic_int_l &dvs_1 &dvs_2>;
|
||||
dvs-gpios = <&gpio7 12 GPIO_ACTIVE_HIGH>,
|
||||
<&gpio7 15 GPIO_ACTIVE_HIGH>;
|
||||
dvs-gpios = <&gpio7 RK_PB4 GPIO_ACTIVE_HIGH>,
|
||||
<&gpio7 RK_PB7 GPIO_ACTIVE_HIGH>;
|
||||
|
||||
regulators {
|
||||
mic_vcc: LDO_REG2 {
|
||||
|
@ -160,14 +160,14 @@
|
|||
|
||||
&vcc_5v {
|
||||
enable-active-high;
|
||||
gpio = <&gpio7 21 GPIO_ACTIVE_HIGH>;
|
||||
gpio = <&gpio7 RK_PC5 GPIO_ACTIVE_HIGH>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&drv_5v>;
|
||||
};
|
||||
|
||||
&vcc50_hdmi {
|
||||
enable-active-high;
|
||||
gpio = <&gpio5 19 GPIO_ACTIVE_HIGH>;
|
||||
gpio = <&gpio5 RK_PC3 GPIO_ACTIVE_HIGH>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&vcc50_hdmi_en>;
|
||||
};
|
||||
|
|
|
@ -56,7 +56,7 @@
|
|||
panel_regulator: panel-regulator {
|
||||
compatible = "regulator-fixed";
|
||||
enable-active-high;
|
||||
gpio = <&gpio7 14 GPIO_ACTIVE_HIGH>;
|
||||
gpio = <&gpio7 RK_PB6 GPIO_ACTIVE_HIGH>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&lcd_enable_h>;
|
||||
regulator-name = "panel_regulator";
|
||||
|
@ -67,7 +67,7 @@
|
|||
vcc18_lcd: vcc18-lcd {
|
||||
compatible = "regulator-fixed";
|
||||
enable-active-high;
|
||||
gpio = <&gpio2 13 GPIO_ACTIVE_HIGH>;
|
||||
gpio = <&gpio2 RK_PB5 GPIO_ACTIVE_HIGH>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&avdd_1v8_disp_en>;
|
||||
regulator-name = "vcc18_lcd";
|
||||
|
@ -79,7 +79,7 @@
|
|||
backlight_regulator: backlight-regulator {
|
||||
compatible = "regulator-fixed";
|
||||
enable-active-high;
|
||||
gpio = <&gpio2 12 GPIO_ACTIVE_HIGH>;
|
||||
gpio = <&gpio2 RK_PB4 GPIO_ACTIVE_HIGH>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&bl_pwr_en>;
|
||||
regulator-name = "backlight_regulator";
|
||||
|
@ -123,14 +123,14 @@
|
|||
|
||||
&vcc_5v {
|
||||
enable-active-high;
|
||||
gpio = <&gpio7 21 GPIO_ACTIVE_HIGH>;
|
||||
gpio = <&gpio7 RK_PC5 GPIO_ACTIVE_HIGH>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&drv_5v>;
|
||||
};
|
||||
|
||||
&vcc50_hdmi {
|
||||
enable-active-high;
|
||||
gpio = <&gpio5 19 GPIO_ACTIVE_HIGH>;
|
||||
gpio = <&gpio5 RK_PC3 GPIO_ACTIVE_HIGH>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&vcc50_hdmi_en>;
|
||||
};
|
||||
|
@ -197,7 +197,7 @@
|
|||
trackpad@2c {
|
||||
compatible = "hid-over-i2c";
|
||||
interrupt-parent = <&gpio7>;
|
||||
interrupts = <3 IRQ_TYPE_EDGE_FALLING>;
|
||||
interrupts = <RK_PA3 IRQ_TYPE_EDGE_FALLING>;
|
||||
reg = <0x2c>;
|
||||
hid-descr-addr = <0x0020>;
|
||||
vcc-supply = <&vcc33_io>;
|
||||
|
|
|
@ -182,8 +182,8 @@
|
|||
&rk808 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pmic_int_l &dvs_1 &dvs_2>;
|
||||
dvs-gpios = <&gpio7 12 GPIO_ACTIVE_HIGH>,
|
||||
<&gpio7 15 GPIO_ACTIVE_HIGH>;
|
||||
dvs-gpios = <&gpio7 RK_PB4 GPIO_ACTIVE_HIGH>,
|
||||
<&gpio7 RK_PB7 GPIO_ACTIVE_HIGH>;
|
||||
|
||||
/delete-property/ vcc6-supply;
|
||||
/delete-property/ vcc12-supply;
|
||||
|
@ -244,7 +244,7 @@
|
|||
|
||||
&vcc50_hdmi {
|
||||
enable-active-high;
|
||||
gpio = <&gpio7 11 GPIO_ACTIVE_HIGH>;
|
||||
gpio = <&gpio7 RK_PB3 GPIO_ACTIVE_HIGH>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&power_hdmi_on>;
|
||||
};
|
||||
|
|
|
@ -55,7 +55,7 @@
|
|||
backlight_regulator: backlight-regulator {
|
||||
compatible = "regulator-fixed";
|
||||
enable-active-high;
|
||||
gpio = <&gpio2 12 GPIO_ACTIVE_HIGH>;
|
||||
gpio = <&gpio2 RK_PB4 GPIO_ACTIVE_HIGH>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&bl_pwr_en>;
|
||||
regulator-name = "backlight_regulator";
|
||||
|
@ -66,7 +66,7 @@
|
|||
panel_regulator: panel-regulator {
|
||||
compatible = "regulator-fixed";
|
||||
enable-active-high;
|
||||
gpio = <&gpio7 14 GPIO_ACTIVE_HIGH>;
|
||||
gpio = <&gpio7 RK_PB6 GPIO_ACTIVE_HIGH>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&lcd_enable_h>;
|
||||
regulator-name = "panel_regulator";
|
||||
|
@ -77,7 +77,7 @@
|
|||
vcc18_lcd: vcc18-lcd {
|
||||
compatible = "regulator-fixed";
|
||||
enable-active-high;
|
||||
gpio = <&gpio2 13 GPIO_ACTIVE_HIGH>;
|
||||
gpio = <&gpio2 RK_PB5 GPIO_ACTIVE_HIGH>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&avdd_1v8_disp_en>;
|
||||
regulator-name = "vcc18_lcd";
|
||||
|
@ -134,14 +134,14 @@
|
|||
|
||||
volum_down {
|
||||
label = "Volum_down";
|
||||
gpios = <&gpio5 11 GPIO_ACTIVE_LOW>;
|
||||
gpios = <&gpio5 RK_PB3 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_VOLUMEDOWN>;
|
||||
debounce-interval = <100>;
|
||||
};
|
||||
|
||||
volum_up {
|
||||
label = "Volum_up";
|
||||
gpios = <&gpio5 10 GPIO_ACTIVE_LOW>;
|
||||
gpios = <&gpio5 RK_PB2 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_VOLUMEUP>;
|
||||
debounce-interval = <100>;
|
||||
};
|
||||
|
@ -165,10 +165,10 @@
|
|||
compatible = "elan,ekth3500";
|
||||
reg = <0x10>;
|
||||
interrupt-parent = <&gpio2>;
|
||||
interrupts = <14 IRQ_TYPE_EDGE_FALLING>;
|
||||
interrupts = <RK_PB6 IRQ_TYPE_EDGE_FALLING>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&touch_int &touch_rst>;
|
||||
reset-gpios = <&gpio2 15 GPIO_ACTIVE_LOW>;
|
||||
reset-gpios = <&gpio2 RK_PB7 GPIO_ACTIVE_LOW>;
|
||||
vcc33-supply = <&vcc33_touch>;
|
||||
vccio-supply = <&vcc33_touch>;
|
||||
};
|
||||
|
@ -211,14 +211,14 @@
|
|||
|
||||
&vcc_5v {
|
||||
enable-active-high;
|
||||
gpio = <&gpio7 21 GPIO_ACTIVE_HIGH>;
|
||||
gpio = <&gpio7 RK_PC5 GPIO_ACTIVE_HIGH>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&drv_5v>;
|
||||
};
|
||||
|
||||
&vcc50_hdmi {
|
||||
enable-active-high;
|
||||
gpio = <&gpio5 19 GPIO_ACTIVE_HIGH>;
|
||||
gpio = <&gpio5 RK_PC3 GPIO_ACTIVE_HIGH>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&vcc50_hdmi_en>;
|
||||
};
|
||||
|
|
|
@ -76,7 +76,7 @@
|
|||
pinctrl-0 = <&pwr_key_h &ap_lid_int_l>;
|
||||
|
||||
power {
|
||||
gpios = <&gpio0 5 GPIO_ACTIVE_HIGH>;
|
||||
gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
|
||||
|
@ -126,7 +126,7 @@
|
|||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd_disabled &sdmmc_cd_gpio
|
||||
&sdmmc_wp_gpio &sdmmc_bus4>;
|
||||
wp-gpios = <&gpio7 10 GPIO_ACTIVE_HIGH>;
|
||||
wp-gpios = <&gpio7 RK_PB2 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
&tsadc {
|
||||
|
|
|
@ -115,7 +115,7 @@
|
|||
cap-mmc-highspeed;
|
||||
cap-sd-highspeed;
|
||||
card-detect-delay = <200>;
|
||||
cd-gpios = <&gpio7 5 GPIO_ACTIVE_LOW>;
|
||||
cd-gpios = <&gpio7 RK_PA5 GPIO_ACTIVE_LOW>;
|
||||
rockchip,default-sample-phase = <90>;
|
||||
num-slots = <1>;
|
||||
sd-uhs-sdr12;
|
||||
|
|
|
@ -57,7 +57,7 @@
|
|||
panel_regulator: panel-regulator {
|
||||
compatible = "regulator-fixed";
|
||||
enable-active-high;
|
||||
gpio = <&gpio7 14 GPIO_ACTIVE_HIGH>;
|
||||
gpio = <&gpio7 RK_PB6 GPIO_ACTIVE_HIGH>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&lcd_enable_h>;
|
||||
regulator-name = "panel_regulator";
|
||||
|
@ -68,7 +68,7 @@
|
|||
vcc18_lcd: vcc18-lcd {
|
||||
compatible = "regulator-fixed";
|
||||
enable-active-high;
|
||||
gpio = <&gpio2 13 GPIO_ACTIVE_HIGH>;
|
||||
gpio = <&gpio2 RK_PB5 GPIO_ACTIVE_HIGH>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&avdd_1v8_disp_en>;
|
||||
regulator-name = "vcc18_lcd";
|
||||
|
@ -80,7 +80,7 @@
|
|||
backlight_regulator: backlight-regulator {
|
||||
compatible = "regulator-fixed";
|
||||
enable-active-high;
|
||||
gpio = <&gpio2 12 GPIO_ACTIVE_HIGH>;
|
||||
gpio = <&gpio2 RK_PB4 GPIO_ACTIVE_HIGH>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&bl_pwr_en>;
|
||||
regulator-name = "backlight_regulator";
|
||||
|
@ -126,14 +126,14 @@
|
|||
|
||||
&vcc_5v {
|
||||
enable-active-high;
|
||||
gpio = <&gpio7 21 GPIO_ACTIVE_HIGH>;
|
||||
gpio = <&gpio7 RK_PC5 GPIO_ACTIVE_HIGH>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&drv_5v>;
|
||||
};
|
||||
|
||||
&vcc50_hdmi {
|
||||
enable-active-high;
|
||||
gpio = <&gpio5 19 GPIO_ACTIVE_HIGH>;
|
||||
gpio = <&gpio5 RK_PC3 GPIO_ACTIVE_HIGH>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&vcc50_hdmi_en>;
|
||||
};
|
||||
|
|
|
@ -61,7 +61,7 @@
|
|||
pinctrl-0 = <&pwr_key_l>;
|
||||
power {
|
||||
label = "Power";
|
||||
gpios = <&gpio0 5 GPIO_ACTIVE_LOW>;
|
||||
gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_POWER>;
|
||||
debounce-interval = <100>;
|
||||
wakeup-source;
|
||||
|
@ -70,7 +70,7 @@
|
|||
|
||||
gpio-restart {
|
||||
compatible = "gpio-restart";
|
||||
gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>;
|
||||
gpios = <&gpio0 RK_PB5 GPIO_ACTIVE_HIGH>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&ap_warm_reset_h>;
|
||||
priority = <200>;
|
||||
|
@ -80,7 +80,7 @@
|
|||
compatible = "mmc-pwrseq-emmc";
|
||||
pinctrl-0 = <&emmc_reset>;
|
||||
pinctrl-names = "default";
|
||||
reset-gpios = <&gpio2 9 GPIO_ACTIVE_HIGH>;
|
||||
reset-gpios = <&gpio2 RK_PB1 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
sdio_pwrseq: sdio-pwrseq {
|
||||
|
@ -96,7 +96,7 @@
|
|||
* - SDIO_RESET_L_WL_REG_ON
|
||||
* - PDN (power down when low)
|
||||
*/
|
||||
reset-gpios = <&gpio4 28 GPIO_ACTIVE_LOW>;
|
||||
reset-gpios = <&gpio4 RK_PD4 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
vcc_5v: vcc-5v {
|
||||
|
@ -178,7 +178,7 @@
|
|||
reg = <0x1b>;
|
||||
clock-output-names = "xin32k", "wifibt_32kin";
|
||||
interrupt-parent = <&gpio0>;
|
||||
interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
|
||||
interrupts = <RK_PA4 IRQ_TYPE_LEVEL_LOW>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pmic_int_l>;
|
||||
rockchip,system-power-controller;
|
||||
|
|
Loading…
Reference in a new issue