commit fe50a7d039 upstream.
There was one place where the timeout value for an operation was
not being set, if a capabilities request was done from idle. Move
the timeout value setting to before where that change might be
requested.
IMHO the cause here is the invisible returns in the macros. Maybe
that's a job for later, though.
Reported-by: Nordmark Claes <Claes.Nordmark@tieto.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4f7f5551a7 upstream.
System may crash after unloading ipmi_si.ko module
because a timer may remain and fire after the module cleaned up resources.
cleanup_one_si() contains the following processing.
/*
* Make sure that interrupts, the timer and the thread are
* stopped and will not run again.
*/
if (to_clean->irq_cleanup)
to_clean->irq_cleanup(to_clean);
wait_for_timer_and_thread(to_clean);
/*
* Timeouts are stopped, now make sure the interrupts are off
* in the BMC. Note that timers and CPU interrupts are off,
* so no need for locks.
*/
while (to_clean->curr_msg || (to_clean->si_state != SI_NORMAL)) {
poll(to_clean);
schedule_timeout_uninterruptible(1);
}
si_state changes as following in the while loop calling poll(to_clean).
SI_GETTING_MESSAGES
=> SI_CHECKING_ENABLES
=> SI_SETTING_ENABLES
=> SI_GETTING_EVENTS
=> SI_NORMAL
As written in the code comments above,
timers are expected to stop before the polling loop and not to run again.
But the timer is set again in the following process
when si_state becomes SI_SETTING_ENABLES.
=> poll
=> smi_event_handler
=> handle_transaction_done
// smi_info->si_state == SI_SETTING_ENABLES
=> start_getting_events
=> start_new_msg
=> smi_mod_timer
=> mod_timer
As a result, before the timer set in start_new_msg() expires,
the polling loop may see si_state becoming SI_NORMAL
and the module clean-up finishes.
For example, hard LOCKUP and panic occurred as following.
smi_timeout was called after smi_event_handler,
kcs_event and hangs at port_inb()
trying to access I/O port after release.
[exception RIP: port_inb+19]
RIP: ffffffffc0473053 RSP: ffff88069fdc3d80 RFLAGS: 00000006
RAX: ffff8806800f8e00 RBX: ffff880682bd9400 RCX: 0000000000000000
RDX: 0000000000000ca3 RSI: 0000000000000ca3 RDI: ffff8806800f8e40
RBP: ffff88069fdc3d80 R8: ffffffff81d86dfc R9: ffffffff81e36426
R10: 00000000000509f0 R11: 0000000000100000 R12: 0000000000]:000000
R13: 0000000000000000 R14: 0000000000000246 R15: ffff8806800f8e00
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0000
--- <NMI exception stack> ---
To fix the problem I defined a flag, timer_can_start,
as member of struct smi_info.
The flag is enabled immediately after initializing the timer
and disabled immediately before waiting for timer deletion.
Fixes: 0cfec916e8 ("ipmi: Start the timer and thread on internal msgs")
Signed-off-by: Yamazaki Masamitsu <m-yamazaki@ah.jp.nec.com>
[Some fairly major changes went into the IPMI driver in 4.15, so this
required a backport as the code had changed and moved to a different
file.]
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7e030d6dff upstream.
The recent changes to add SMBIOS (DMI) IPMI interfaces as platform
devices caused DMI to be selected before ACPI, causing ACPI type
of operations to not work.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 392a17b10e upstream.
When I set the timeout to a specific value such as 500ms, the timeout
event will not happen in time due to the overflow in function
check_msg_timeout:
...
ent->timeout -= timeout_period;
if (ent->timeout > 0)
return;
...
The type of timeout_period is long, but ent->timeout is unsigned long.
This patch makes the type consistent.
Reported-by: Weilong Chen <chenweilong@huawei.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Tested-by: Weilong Chen <chenweilong@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The medium sized change is adding a platform device for IPMI entries
in the DMI table. Otherwise there is no auto loading for IPMI
devices if they are only in the DMI table.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlljviUACgkQIXnXXONXERdehACfeQNbSg4+HExytHk2BgT5WfN3
iJoAoIKWINgfR7xHSrQtB3ybzznlKMYY
=proo
-----END PGP SIGNATURE-----
Merge tag 'for-linus-4.13-v2' of git://github.com/cminyard/linux-ipmi
Pull IPMI updates from Corey Minyard:
"Some small fixes for IPMI, and one medium sized changed.
The medium sized change is adding a platform device for IPMI entries
in the DMI table. Otherwise there is no auto loading for IPMI devices
if they are only in the DMI table"
* tag 'for-linus-4.13-v2' of git://github.com/cminyard/linux-ipmi:
ipmi:ssif: Add missing unlock in error branch
char: ipmi: constify bmc_dev_attr_group and bmc_device_type
ipmi:ssif: Check dev before setting drvdata
ipmi: Convert DMI handling over to a platform device
ipmi: Create a platform device for a DMI-specified IPMI interface
ipmi: use rcu lock around call to intf->handlers->sender()
ipmi:ssif: Use i2c_adapter_id instead of adapter->nr
ipmi: Use the proper default value for register size in ACPI
ipmi_ssif: remove redundant null check on array client->adapter->name
ipmi/watchdog: fix watchdog timeout set on reboot
ipmi_ssif: unlock on allocation failure
Pull misc compat stuff updates from Al Viro:
"This part is basically untangling various compat stuff. Compat
syscalls moved to their native counterparts, getting rid of quite a
bit of double-copying and/or set_fs() uses. A lot of field-by-field
copyin/copyout killed off.
- kernel/compat.c is much closer to containing just the
copyin/copyout of compat structs. Not all compat syscalls are gone
from it yet, but it's getting there.
- ipc/compat_mq.c killed off completely.
- block/compat_ioctl.c cleaned up; floppy compat ioctls moved to
drivers/block/floppy.c where they belong. Yes, there are several
drivers that implement some of the same ioctls. Some are m68k and
one is 32bit-only pmac. drivers/block/floppy.c is the only one in
that bunch that can be built on biarch"
* 'misc.compat' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
mqueue: move compat syscalls to native ones
usbdevfs: get rid of field-by-field copyin
compat_hdio_ioctl: get rid of set_fs()
take floppy compat ioctls to sodding floppy.c
ipmi: get rid of field-by-field __get_user()
ipmi: get COMPAT_IPMICTL_RECEIVE_MSG in sync with the native one
rt_sigtimedwait(): move compat to native
select: switch compat_{get,put}_fd_set() to compat_{get,put}_bitmap()
put_compat_rusage(): switch to copy_to_user()
sigpending(): move compat to native
getrlimit()/setrlimit(): move compat to native
times(2): move compat to native
compat_{get,put}_bitmap(): use unsafe_{get,put}_user()
fb_get_fscreeninfo(): don't bother with do_fb_ioctl()
do_sigaltstack(): lift copying to/from userland into callers
take compat_sys_old_getrlimit() to native syscall
trim __ARCH_WANT_SYS_OLD_GETRLIMIT
When getting flags, a response to a different message would
result in a deadlock because of a missing unlock. Add that
unlock and a comment. Found by static analysis.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable@vger.kernel.org # 3.19
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Rename:
wait_queue_t => wait_queue_entry_t
'wait_queue_t' was always a slight misnomer: its name implies that it's a "queue",
but in reality it's a queue *entry*. The 'real' queue is the wait queue head,
which had to carry the name.
Start sorting this out by renaming it to 'wait_queue_entry_t'.
This also allows the real structure name 'struct __wait_queue' to
lose its double underscore and become 'struct wait_queue_entry',
which is the more canonical nomenclature for such data types.
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Now that the IPMI DMI code creates a platform device for IPMI devices
in the firmware, use that instead of handling all the DMI work
in the IPMI drivers themselves.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: Andy Lutomirski <luto@kernel.org>
Create a platform device for each IPMI device in the DMI table,
a separate kind of device for SSIF types and for KCS, BT, and
SMIC types. This is so auto-loading IPMI devices will work
from just SMBIOS tables.
This also adds the ability to extract the slave address from
the SMBIOS tables, so that when the driver uses ACPI-specified
interfaces, it can still extract the slave address from SMBIOS.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: Andy Lutomirski <luto@kernel.org>
A vendor with a system having more than 128 CPUs occasionally encounters
the following crash during shutdown. This is not an easily reproduceable
event, but the vendor was able to provide the following analysis of the
crash, which exhibits the same footprint each time.
crash> bt
PID: 0 TASK: ffff88017c70ce70 CPU: 5 COMMAND: "swapper/5"
#0 [ffff88085c143ac8] machine_kexec at ffffffff81059c8b
#1 [ffff88085c143b28] __crash_kexec at ffffffff811052e2
#2 [ffff88085c143bf8] crash_kexec at ffffffff811053d0
#3 [ffff88085c143c10] oops_end at ffffffff8168ef88
#4 [ffff88085c143c38] no_context at ffffffff8167ebb3
#5 [ffff88085c143c88] __bad_area_nosemaphore at ffffffff8167ec49
#6 [ffff88085c143cd0] bad_area_nosemaphore at ffffffff8167edb3
#7 [ffff88085c143ce0] __do_page_fault at ffffffff81691d1e
#8 [ffff88085c143d40] do_page_fault at ffffffff81691ec5
#9 [ffff88085c143d70] page_fault at ffffffff8168e188
[exception RIP: unknown or invalid address]
RIP: ffffffffa053c800 RSP: ffff88085c143e28 RFLAGS: 00010206
RAX: ffff88017c72bfd8 RBX: ffff88017a8dc000 RCX: ffff8810588b5ac8
RDX: ffff8810588b5a00 RSI: ffffffffa053c800 RDI: ffff8810588b5a00
RBP: ffff88085c143e58 R8: ffff88017c70d408 R9: ffff88017a8dc000
R10: 0000000000000002 R11: ffff88085c143da0 R12: ffff8810588b5ac8
R13: 0000000000000100 R14: ffffffffa053c800 R15: ffff8810588b5a00
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018
<IRQ stack>
[exception RIP: cpuidle_enter_state+82]
RIP: ffffffff81514192 RSP: ffff88017c72be50 RFLAGS: 00000202
RAX: 0000001e4c3c6f16 RBX: 000000000000f8a0 RCX: 0000000000000018
RDX: 0000000225c17d03 RSI: ffff88017c72bfd8 RDI: 0000001e4c3c6f16
RBP: ffff88017c72be78 R8: 000000000000237e R9: 0000000000000018
R10: 0000000000002494 R11: 0000000000000001 R12: ffff88017c72be20
R13: ffff88085c14f8e0 R14: 0000000000000082 R15: 0000001e4c3bb400
ORIG_RAX: ffffffffffffff10 CS: 0010 SS: 0018
This is the corresponding stack trace
It has crashed because the area pointed with RIP extracted from timer
element is already removed during a shutdown process.
The function is smi_timeout().
And we think ffff8810588b5a00 in RDX is a parameter struct smi_info
crash> rd ffff8810588b5a00 20
ffff8810588b5a00: ffff8810588b6000 0000000000000000 .`.X............
ffff8810588b5a10: ffff880853264400 ffffffffa05417e0 .D&S......T.....
ffff8810588b5a20: 24a024a000000000 0000000000000000 .....$.$........
ffff8810588b5a30: 0000000000000000 0000000000000000 ................
ffff8810588b5a30: 0000000000000000 0000000000000000 ................
ffff8810588b5a40: ffffffffa053a040 ffffffffa053a060 @.S.....`.S.....
ffff8810588b5a50: 0000000000000000 0000000100000001 ................
ffff8810588b5a60: 0000000000000000 0000000000000e00 ................
ffff8810588b5a70: ffffffffa053a580 ffffffffa053a6e0 ..S.......S.....
ffff8810588b5a80: ffffffffa053a4a0 ffffffffa053a250 ..S.....P.S.....
ffff8810588b5a90: 0000000500000002 0000000000000000 ................
Unfortunately the top of this area is already detroyed by someone.
But because of two reasonns we think this is struct smi_info
1) The address included in between ffff8810588b5a70 and ffff8810588b5a80:
are inside of ipmi_si_intf.c see crash> module ffff88085779d2c0
2) We've found the area which point this.
It is offset 0x68 of ffff880859df4000
crash> rd ffff880859df4000 100
ffff880859df4000: 0000000000000000 0000000000000001 ................
ffff880859df4010: ffffffffa0535290 dead000000000200 .RS.............
ffff880859df4020: ffff880859df4020 ffff880859df4020 @.Y.... @.Y....
ffff880859df4030: 0000000000000002 0000000000100010 ................
ffff880859df4040: ffff880859df4040 ffff880859df4040 @@.Y....@@.Y....
ffff880859df4050: 0000000000000000 0000000000000000 ................
ffff880859df4060: 0000000000000000 ffff8810588b5a00 .........Z.X....
ffff880859df4070: 0000000000000001 ffff880859df4078 ........x@.Y....
If we regards it as struct ipmi_smi in shutdown process
it looks consistent.
The remedy for this apparent race is affixed below.
Signed-off-by: Tony Camuso <tcamuso@redhat.com>
Cc: stable@vger.kernel.org # 3.19
This was first introduced in 7ea0ed2b5b ipmi: Make the
message handler easier to use for SMI interfaces
where some code was moved outside of the rcu_read_lock()
and the lock was not added.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
The null check on client->adapter->name is redundant as name is an
array of I2C_NAME_SIZE chars and hence can never be null. We may as
well remove this redundant check.
Detected by CoverityScan, CID#1375918 ("Array compared against 0")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
-----BEGIN PGP SIGNATURE-----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=lbS7
-----END PGP SIGNATURE-----
Merge tag 'hwparam-20170420' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
Pull hw lockdown support from David Howells:
"Annotation of module parameters that configure hardware resources
including ioports, iomem addresses, irq lines and dma channels.
This allows a future patch to prohibit the use of such module
parameters to prevent that hardware from being abused to gain access
to the running kernel image as part of locking the kernel down under
UEFI secure boot conditions.
Annotations are made by changing:
module_param(n, t, p)
module_param_named(n, v, t, p)
module_param_array(n, t, m, p)
to:
module_param_hw(n, t, hwtype, p)
module_param_hw_named(n, v, t, hwtype, p)
module_param_hw_array(n, t, hwtype, m, p)
where the module parameter refers to a hardware setting
hwtype specifies the type of the resource being configured. This can
be one of:
ioport Module parameter configures an I/O port
iomem Module parameter configures an I/O mem address
ioport_or_iomem Module parameter could be either (runtime set)
irq Module parameter configures an I/O port
dma Module parameter configures a DMA channel
dma_addr Module parameter configures a DMA buffer address
other Module parameter configures some other value
Note that the hwtype is compile checked, but not currently stored (the
lockdown code probably won't require it). It is, however, there for
future use.
A bonus is that the hwtype can also be used for grepping.
The intention is for the kernel to ignore or reject attempts to set
annotated module parameters if lockdown is enabled. This applies to
options passed on the boot command line, passed to insmod/modprobe or
direct twiddling in /sys/module/ parameter files.
The module initialisation then needs to handle the parameter not being
set, by (1) giving an error, (2) probing for a value or (3) using a
reasonable default.
What I can't do is just reject a module out of hand because it may
take a hardware setting in the module parameters. Some important
modules, some ipmi stuff for instance, both probe for hardware and
allow hardware to be manually specified; if the driver is aborts with
any error, you don't get any ipmi hardware.
Further, trying to do this entirely in the module initialisation code
doesn't protect against sysfs twiddling.
[!] Note that in and of itself, this series of patches should have no
effect on the the size of the kernel or code execution - that is
left to a patch in the next series to effect. It does mark
annotated kernel parameters with a KERNEL_PARAM_FL_HWPARAM flag in
an already existing field"
* tag 'hwparam-20170420' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs: (38 commits)
Annotate hardware config module parameters in sound/pci/
Annotate hardware config module parameters in sound/oss/
Annotate hardware config module parameters in sound/isa/
Annotate hardware config module parameters in sound/drivers/
Annotate hardware config module parameters in fs/pstore/
Annotate hardware config module parameters in drivers/watchdog/
Annotate hardware config module parameters in drivers/video/
Annotate hardware config module parameters in drivers/tty/
Annotate hardware config module parameters in drivers/staging/vme/
Annotate hardware config module parameters in drivers/staging/speakup/
Annotate hardware config module parameters in drivers/staging/media/
Annotate hardware config module parameters in drivers/scsi/
Annotate hardware config module parameters in drivers/pcmcia/
Annotate hardware config module parameters in drivers/pci/hotplug/
Annotate hardware config module parameters in drivers/parport/
Annotate hardware config module parameters in drivers/net/wireless/
Annotate hardware config module parameters in drivers/net/wan/
Annotate hardware config module parameters in drivers/net/irda/
Annotate hardware config module parameters in drivers/net/hamradio/
Annotate hardware config module parameters in drivers/net/ethernet/
...
systemd by default starts watchdog on reboot and sets the timer to
ShutdownWatchdogSec=10min. Reboot handler in ipmi_watchdog than reduces
the timer to 120s which is not enough time to boot a Xen machine with
a lot of RAM. As a result the machine is rebooted the second time
during the long run of (XEN) Scrubbing Free RAM.....
Fix this by setting the timer to 120s only if it was previously
set to a low value.
Signed-off-by: Valentin Vidic <Valentin.Vidic@CARNet.hr>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
We should unlock and re-enable IRQs if this allocation fails.
Fixes: 259307074b ("ipmi: Add SMBus interface driver (SSIF) ")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Commit c49c097610 ("ipmi: Don't call receive handler in the
panic context") means that the panic_recv_free is not called during a
panic and the atomic count does not drop to 0.
Fix this by only expecting one decrement of the atomic variable
which comes from panic_smi_free.
Signed-off-by: Robert Lippert <rlippert@google.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
When the kernel is running in secure boot mode, we lock down the kernel to
prevent userspace from modifying the running kernel image. Whilst this
includes prohibiting access to things like /dev/mem, it must also prevent
access by means of configuring driver modules in such a way as to cause a
device to access or modify the kernel image.
To this end, annotate module_param* statements that refer to hardware
configuration and indicate for future reference what type of parameter they
specify. The parameter parser in the core sees this information and can
skip such parameters with an error message if the kernel is locked down.
The module initialisation then runs as normal, but just sees whatever the
default values for those parameters is.
Note that we do still need to do the module initialisation because some
drivers have viable defaults set in case parameters aren't specified and
some drivers support automatic configuration (e.g. PNP or PCI) in addition
to manually coded parameters.
This patch annotates drivers in drivers/char/ipmi/.
Suggested-by: Alan Cox <gnomes@lxorguk.ukuu.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Corey Minyard <cminyard@mvista.com>
cc: openipmi-developer@lists.sourceforge.net
Commit 1abf71e moved the creation of new_smi->dev to earlier in the init
sequence in order to provide infrastructure for log printing.
However, the init_name was created with a hard-coded value of zero. This
presents a problem in systems with more than one interface, producing a
call trace in dmesg.
To correct the problem, simply use smi_num instead of the hard-coded
value of zero.
Tested on a lenovo x3950.
Signed-off-by: Tony Camuso <tcamuso@redhat.com>
There was actually a more general problem, the platform device wasn't
being set correctly, either, and there was a possible (though extremely
unlikely) race on smi_num. Add locks to clean up the race and use the
proper value for the platform device, too.
Tested on qemu in various configurations.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
The ast2500 SoCs contain the same IPMI BT device.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Use setup_timer() instead of init_timer() to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
msg_written_handler() may set ssif_info->multi_data to NULL
when using ipmitool to write fru.
Before setting ssif_info->multi_data to NULL, add new local
pointer "data_to_send" and store correct i2c data pointer to
it to fix NULL pointer kernel panic and incorrect ssif_info->multi_pos.
Signed-off-by: Joeseph Chang <joechang@codeaurora.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: stable@vger.kernel.org # 3.19-
Fix up affected files that include this signal functionality via sched.h.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The registers for the bt-bmc device live under the Aspeed LPC
controller. Devicetree bindings have recently been introduced for the
LPC controller where the "host" portion of the LPC register space is
described as a syscon device. Future devicetrees describing the bt-bmc
device should nest its node under the appropriate "simple-mfd", "syscon"
compatible node.
This change allows the bt-bmc driver to function with both syscon and
non-syscon- based devicetree descriptions by always using a regmap for
register access, either retrieved from the parent syscon device or
instantiated if none exists.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Declare ipmi_smi_handlers structures as const as they are only passed as
an argument to the function ipmi_register_smi. This argument is of type
const, so ipmi_smi_handlers structures having similar properties can be
declared const too.
Done using Coccinelle:
@r1 disable optional_qualifier@
identifier i;
position p;
@@
static struct ipmi_smi_handlers i@p={...};
@ok1@
identifier r1.i;
position p;
@@
ipmi_register_smi(&i@p,...)
@bad@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct ipmi_smi_handlers i;
Size details after cross compiling the .o file for powerpc architecture
File size before:
text data bss dec hex filename
2777 288 0 3065 bf9 drivers/char/ipmi/ipmi_powernv.o
File size after:
text data bss dec hex filename
2873 192 0 3065 bf9 drivers/char/ipmi/ipmi_powernv.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
convertion printk() to pr_xxx() and removal of an unused module
parameter. Some small bug fixes and enhancements.
This also adds a post softdep from the IPMI core module to the
IPMI device interface. Many people have complained that the device
interface isn't automatically avaiable when IPMI is loaded. I don't
want to make the device interface mandatory, though, plenty of people
use IPMI internally (like with ACPI) and don't need a device interface
or the added possible security entry. A softdep should make it work
"out of the box" but allow people to not have it if they don't want it.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlhSE9cACgkQIXnXXONXERe6iACgsiU5/LG4tbKu9EyZXp5isRw6
AdsAn1dT08aobOzJhFI3dVx6oTnJQDDC
=ifi5
-----END PGP SIGNATURE-----
Merge tag 'for-linus-4.10' of git://git.code.sf.net/p/openipmi/linux-ipmi
Pull IPMI updates from Corey Minyard:
"Various small fixes for IPMI. Cleanups in the documentation and
convertion printk() to pr_xxx() and removal of an unused module
parameter. Some small bug fixes and enhancements.
This also adds a post softdep from the IPMI core module to the IPMI
device interface. Many people have complained that the device
interface isn't automatically avaiable when IPMI is loaded. I don't
want to make the device interface mandatory, though, plenty of people
use IPMI internally (like with ACPI) and don't need a device interface
or the added possible security entry. A softdep should make it work
'out of the box' but allow people to not have it if they don't want
it"
* tag 'for-linus-4.10' of git://git.code.sf.net/p/openipmi/linux-ipmi:
ipmi: create hardware-independent softdep for ipmi_devintf
ipmi: Fix sequence number handling
ipmi: Pick up slave address from SMBIOS on an ACPI device
ipmi_si: Clean up printks
Move platform device creation earlier in the initialization
ipmi: Update documentation
ipmi_ssif: Remove an unused module parameter
ipmi: Periodically check for events, not messages
When a computer has an IPMI system interface, the device interface
is most probably also desired. Autoloading of ipmi_devintf currently
works only if ipmi_si has allocated a platform device. That doesn't
happen if the SI interface was detected e.g. via ACPI. But ACPI
detection is preferred these days, see e.g. kernel.org bug 46741.
This patch introduces a softdep in place of the existing modalias
for ipmi_devintf.
Signed-off-by: Martin Wilck <mwilck@suse.com>
Suggested-by: Takashi Iwai <tiwai@suse.com>
I moved this to ipmi_msghandler.c, so it works for all IPMI
interfaces. Retested by Martin.
Tested-by: Martin Wilck <mwilck@suse.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
The IPMI message handler uses a message id that the lower-layer
preserved to track the sequence number of the message. The macros
that handled these sequence numbers were somewhat broken as they
could result in sequence number truncation and they were not
doing an "and" of the proper number of bits.
I think this actually is not a problem, because the truncation
should be harmless and the improper "and" didn't hurt anything
because sequence number generation used the same improper "and"
and wouldn't generate a sequence number that would get
truncated wrong. However, it should be fixed.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
When added by ACPI, the information does not contain the slave address
of the BMC. However, that information is available from SMBIOS. So
if we add a device that doesn't have a slave address, look at the other
devices that are duplicate interfaces and see if they have a slave
address.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Some logs are printed out early using smi->dev, but on a platform device
that is not created until later. So move the creation of that device
structure earlier in the sequence so it can be used for printing.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
The Aspeed SoCs have two BT interfaces : one is IPMI compliant and the
other is H8S/2168 compliant.
The current ipmi/bt-bmc driver implements the IPMI version and we
should reflect its nature in the compatible node name using
'aspeed,ast2400-ibt-bmc' instead of 'aspeed,ast2400-bt-bmc'. The
latter should be used for a H8S interface driver if it is implemented
one day.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Commit d9b7e4f717 ("ipmi: Periodically check to see if irqs and
messages are set right") to verify the contents of global events.
However, the wrong function was being called in some cases, checking
for messages, not events.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Tested-by: Jason DiPietro <J.DiPietro@F5.com>
Corey Minyard