Although GICv3 doesn't directly offers support for wake-up interrupts
and relies on external HW for this, it shouldn't prevent the driver
for such HW from doing it work.
Let's set the required flags on the irq_chip structures.
Reported-by: Lina Iyer <ilina@codeaurora.org>
Tested-by: Lina Iyer <ilina@codeaurora.org>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
(cherry picked from commit 4110b5cbb0)
This reverts commit 1d965a3e12797e6561df8b5fcc16ad1d60182dab.
Shrinking the udelay from 50 to 10 causes lost IPIs and hangs on
suspend so let's revert to behavior from previous releases.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Acked-by: Jun Li <jun.li@nxp.com>
Shorten the delay time from 50us to be 10us introduced by
commit 58cef5f23bd0 ("MLK-16804-04 driver: irqchip: Add IPI SW workaround for imx8mq"),
tested various basic cases and didn't find issues.
CC: Bai Ping <ping.bai@nxp.com>
Acked-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Fixes: a2e6a7833495 (MLK-16136-9 irqchip: imx-irqsteer: adjust irq config
via 'endian')
This patch fixes mask register offset calculation, when endian is not
default value 0 (i.e imx8mq).
Signed-off-by: Antoine Bouyer <antoine.bouyer@nxp.com>
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Add runtime pm to manage irqsteer clock and its power domain in system
idle and suspend status to save power.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Tested-by: Guoniu.Zhou <guoniu.zhou@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Once irqsteer controller is power off during suspend, the registers
are lost, it should restore the registers after resume back.
BuildInfo:
- SCFW a479ff78, IMX-MKIMAGE ff9860c5, ATF 923651a
- U-Boot 2017.03-00691-g96cf020
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Tested-by: Pandy.gao <pandy.gao@nxp.com>
Acked-by: Pandy.gao <pandy.gao@nxp.com>
On i.MX8MQ, when the CPU core is in power down state,
the IPI can NOT wakeup the core anymore(ERR011171), so using the
external IRQ32 to wakeup the core in power down idle
state successfully.
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Reviewed-by: Anson Huang <anson.huang@nxp.com>
Change the irq configurations with adding endianness
determination for different platforms which may choose
different kinds of endianess.
Signed-off-by: Fancy Fang <chen.fang@nxp.com>
Correct several macro definitions related with irqsteer
to avoid incorrect expression calculation due to operators
priority.
Signed-off-by: Fancy Fang <chen.fang@nxp.com>
The intmux module is used to output internal interrupt in subsystem
to system with 32-to-8 configuration. It has several multiplex
channels depends on system. intmux is introduced in KL28Z reference
manual.
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
The type of irqstat in irqsteer_irqchip_data unsigned long, actually
it needs to be 32bits width, so use unsigned int.
And use sizeof(irqsteer_data->irqstat[0]), instead of 4 when alloc
memory for irqsteer_data.
for_each_set_bit needs the second param type is unsigned long *, so
cast the irqsteer_data->irqstat to unsigned long *, this is safe here.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The IrqSteer module redirects/steers the incoming interrupts to output
interrupts of a selected/designated channel as specified by a set of
configuration registers.
NXP i.MX8x chips integrate IrqSteer controller for some DSC to share irq
line for all modules in the subsystem which can reduce the IRQ lines
connected to the parent interrupt controller GIC, so IrqSteer irqchip
acts as the second irq domain in the system.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
[ Upstream commit 0702bc4d2f ]
When compiling bmips with SMP disabled, the build fails with:
drivers/irqchip/irq-bcm7038-l1.o: In function `bcm7038_l1_cpu_offline':
drivers/irqchip/irq-bcm7038-l1.c:242: undefined reference to `irq_set_affinity_locked'
make[5]: *** [vmlinux] Error 1
Fix this by adding and setting bcm7038_l1_cpu_offline only when actually
compiling for SMP. It wouldn't have been used anyway, as it requires
CPU_HOTPLUG, which in turn requires SMP.
Fixes: 34c535793b ("irqchip/bcm7038-l1: Implement irq_cpu_offline() callback")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c1797b11a0 upstream.
On a NUMA system, if an ITS is local to an offline node, the ITS driver may
pick an offline CPU to bind the LPI. In this case, pick an online CPU (and
the first one will do).
But on some systems, binding an LPI to non-local node CPU may cause
deadlock (see Cavium erratum 23144). In this case, just fail the activate
and return an error code.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Sumit Garg <sumit.garg@linaro.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20180622095254.5906-5-marc.zyngier@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1bc2463cee upstream.
When the interrupts for a combiner span multiple registers it must be
checked if any interrupts have been asserted on each register before
checking for spurious interrupts.
Checking each register seperately leads to false positive warnings.
[ tglx: Massaged changelog ]
Fixes: f20cc9b00c ("irqchip/qcom: Add IRQ combiner driver")
Signed-off-by: Agustin Vega-Frias <agustinv@codeaurora.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: timur@codeaurora.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/1525184090-26143-1-git-send-email-agustinv@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 95a2562590 ]
On some platforms there's an ITS available but it's not enabled
because reading or writing the registers is denied by the
firmware. In fact, reading or writing them will cause the system
to reset. We could remove the node from DT in such a case, but
it's better to skip nodes that are marked as "disabled" in DT so
that we can describe the hardware that exists and use the status
property to indicate how the firmware has configured things.
Cc: Stuart Yoder <stuyoder@gmail.com>
Cc: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aa08192a25 upstream.
Most MMIO GIC register accesses use a 1-hot bit scheme that
avoids requiring any form of locking. This isn't true for the
GICD_ICFGRn registers, which require a RMW sequence.
Unfortunately, we seem to be missing a lock for these particular
accesses, which could result in a race condition if changing the
trigger type on any two interrupts within the same set of 16
interrupts (and thus controlled by the same CFGR register).
Introduce a private lock in the GIC common comde for this
particular case, making it cover both GIC implementations
in one go.
Cc: stable@vger.kernel.org
Signed-off-by: Aniruddha Banerjee <aniruddhab@nvidia.com>
[maz: updated changelog]
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ebe2f87180 ]
The ACPI specification says OS shouldn't attempt to use GICC configuration
parameters if the flag ACPI_MADT_ENABLED is cleared. The ARM64-SMP code
skips the disabled GICC entries but not causing any issue. However the
current GICv3 driver probe bails out causing kernel panic() instead of
skipping the disabled GICC interfaces. This issue happens on systems
where redistributor regions are not in the always-on power domain and
one of GICC interface marked with ACPI_MADT_ENABLED=0.
This patch does the two things to fix the panic.
- Don't return an error in gic_acpi_match_gicc() for disabled GICC entry.
- No need to keep GICR region information for disabled GICC entry.
Observed kernel crash on QDF2400 platform GICC entry is disabled.
Kernel crash traces:
Kernel panic - not syncing: No interrupt controller found.
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.13.5 #26
[<ffff000008087770>] dump_backtrace+0x0/0x218
[<ffff0000080879dc>] show_stack+0x14/0x20
[<ffff00000883b078>] dump_stack+0x98/0xb8
[<ffff0000080c5c14>] panic+0x118/0x26c
[<ffff000008b62348>] init_IRQ+0x24/0x2c
[<ffff000008b609fc>] start_kernel+0x230/0x394
[<ffff000008b601e4>] __primary_switched+0x64/0x6c
---[ end Kernel panic - not syncing: No interrupt controller found.
Disabled GICC subtable example:
Subtable Type : 0B [Generic Interrupt Controller]
Length : 50
Reserved : 0000
CPU Interface Number : 0000003D
Processor UID : 0000003D
Flags (decoded below) : 00000000
Processor Enabled : 0
Performance Interrupt Trig Mode : 0
Virtual GIC Interrupt Trig Mode : 0
Parking Protocol Version : 00000000
Performance Interrupt : 00000017
Parked Address : 0000000000000000
Base Address : 0000000000000000
Virtual GIC Base Address : 0000000000000000
Hypervisor GIC Base Address : 0000000000000000
Virtual GIC Interrupt : 00000019
Redistributor Base Address : 0000FFFF88F40000
ARM MPIDR : 000000000000000D
Efficiency Class : 00
Reserved : 000000
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4f2c7583e3 upstream.
When struct its_device instances are created, the nr_ites member
will be set to a power of 2 that equals or exceeds the requested
number of MSIs passed to the msi_prepare() callback. At the same
time, the LPI map is allocated to be some multiple of 32 in size,
where the allocated size may be less than the requested size
depending on whether a contiguous range of sufficient size is
available in the global LPI bitmap.
This may result in the situation where the nr_ites < nr_lpis, and
since nr_ites is what we program into the hardware when we map the
device, the additional LPIs will be non-functional.
For bog standard hardware, this does not really matter. However,
in cases where ITS device IDs are shared between different PCIe
devices, we may end up allocating these additional LPIs without
taking into account that they don't actually work.
So let's make nr_ites at least 32. This ensures that all allocated
LPIs are 'live', and that its_alloc_device_irq() will fail when
attempts are made to allocate MSIs beyond what was allocated in
the first place.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
[maz: updated comment]
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 285cb4f623 upstream.
Commit 7778c4b27c ("irqchip: mips-gic: Use pcpu_masks to avoid reading
GIC_SH_MASK*") removed the read of the hardware mask register when
handling shared interrupts, instead using the driver's shadow pcpu_masks
entry as the effective mask. Unfortunately this did not take account of
the write to pcpu_masks during gic_shared_irq_domain_map, which
effectively unmasks the interrupt early. If an interrupt is asserted,
gic_handle_shared_int decodes and processes the interrupt even though it
has not yet been unmasked via gic_unmask_irq, which also sets the
appropriate bit in pcpu_masks.
On the MIPS Boston board, when a console command line of
"console=ttyS0,115200n8r" is passed, the modem status IRQ is enabled in
the UART, which is immediately raised to the GIC. The interrupt has been
mapped, but no handler has yet been registered, nor is it expected to be
unmasked. However, the write to pcpu_masks in gic_shared_irq_domain_map
has effectively unmasked it, resulting in endless reports of:
[ 5.058454] irq 13, desc: ffffffff80a7ad80, depth: 1, count: 0, unhandled: 0
[ 5.062057] ->handle_irq(): ffffffff801b1838,
[ 5.062175] handle_bad_irq+0x0/0x2c0
Where IRQ 13 is the UART interrupt.
To fix this, just remove the write to pcpu_masks in
gic_shared_irq_domain_map. The existing write in gic_unmask_irq is the
correct place for what is now the effective unmasking.
Cc: stable@vger.kernel.org
Fixes: 7778c4b27c ("irqchip: mips-gic: Use pcpu_masks to avoid reading GIC_SH_MASK*")
Signed-off-by: Matt Redfearn <matt.redfearn@mips.com>
Reviewed-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 21ec30c0ef upstream.
A DMB instruction can be used to ensure the relative order of only
memory accesses before and after the barrier. Since writes to system
registers are not memory operations, barrier DMB is not sufficient
for observability of memory accesses that occur before ICC_SGI1R_EL1
writes.
A DSB instruction ensures that no instructions that appear in program
order after the DSB instruction, can execute until the DSB instruction
has completed.
Cc: stable@vger.kernel.org
Acked-by: Will Deacon <will.deacon@arm.com>,
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e9990d70e8 ]
The comparison of u32 nregs being less than zero is never true since
nregs is unsigned. Fix this by making nregs a signed integer.
Fixes: f20cc9b00c ("irqchip/qcom: Add IRQ combiner driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: kernel-janitors@vger.kernel.org
Cc: Jason Cooper <jason@lakedaemon.net>
Link: https://lkml.kernel.org/r/20171117183553.2739-1-colin.king@canonical.com
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 00ee9a1ca5 upstream.
Fix child-node lookup during initialisation, which ended up searching
the whole device tree depth-first starting at the parent rather than
just matching on its children.
To make things worse, the parent gic node was prematurely freed, while
the ppi-partitions node was leaked.
Fixes: e3825ba1af ("irqchip/gic-v3: Add support for partitioned PPIs")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The only usage of the irq_gc_mask_disable_reg_and_ack() function
is by the Tango irqchip driver. This usage is replaced by the
irq_gc_mask_disable_and_ack_set() function since it provides the
intended functionality.
Fixes: 4bba66899a ("irqchip/tango: Add support for Sigma Designs SMP86xx/SMP87xx interrupt controller")
Acked-by: Mans Rullgard <mans@mansr.com>
Acked-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The current ITS driver works fine as long as normal memory and GICR
regions are located within the lower 48bit (>=0 && <2^48) physical
address space. Some of the registers GICR_PEND/PROP, GICR_VPEND/VPROP
and GITS_CBASER are handled properly but not all when configuring
the hardware with 52bit physical address.
This patch does the following changes to support 52bit PA.
-Handle 52bit PA in GITS_BASERn.
-Fix ITT_addr width to 52bits, bits[51:8].
-Fix RDbase width to 52bits, bits[51:16].
-Fix VPT_addr width to 52bits, bits[51:16].
Definition of the GITS_BASERn register when ITS PageSize is 64KB:
-Bits[47:16] of the register provide bits[47:16] of the table PA.
-Bits[15:12] of the register provide bits[51:48] of the table PA.
-Bits[15:00] of the base physical address are 0.
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The VCPU table consists of vPE entries, and its size provides the number
of VPEs supported by GICv4 hardware. Unfortunately the maximum size of
the VPE table is not discoverable like Device table. All VLPI commands
limits the number of bits to 16 to hold VPEID, which is index into VCPU
table. Don't apply DEVID bits for VCPU table instead assume maximum bits
to 16.
ITS log messages on QDF2400 without fix:
allocated 524288 Devices (indirect, esz 8, psz 64K, shr 1)
allocated 8192 Interrupt Collections (flat, esz 8, psz 64K, shr 1)
Virtual CPUs Table too large, reduce ids 32->26
Virtual CPUs too large, reduce ITS pages 8192->256
allocated 2097152 Virtual CPUs (flat, esz 8, psz 64K, shr 1)
ITS log messages on QDF2400 with fix:
allocated 524288 Devices (indirect, esz 8, psz 64K, shr 1)
allocated 8192 Interrupt Collections (flat, esz 8, psz 64K, shr 1)
allocated 65536 Virtual CPUs (flat, esz 8, psz 64K, shr 1)
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The driver probe path hits 'BUG_ON(entries != vpe_proxy.dev->nr_ites)'
on systems where it has VLPI capability, doesn't support direct LPI
feature and boot with a single CPU.
Relax the BUG_ON() condition to fix the issue.
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Commit 7778c4b27c ("irqchip: mips-gic: Use pcpu_masks to avoid reading
GIC_SH_MASK*") adjusted the way we handle masking interrupts to set &
clear the interrupt's bit in each pcpu_mask. This allows us to avoid
needing to read the GIC mask registers and perform a bitwise and of
their values with the pending & pcpu_masks.
Unfortunately this didn't quite work for IPIs, which were mapped to a
particular CPU/VP during initialisation but never set the affinity or
effective_affinity fields of their struct irq_desc. This led to them
losing their affinity when gic_unmask_irq() was called for them, and
they'd all become affine to cpu0.
Fix this by:
1) Setting the effective affinity of interrupts in
gic_shared_irq_domain_map(), which is where we actually map an
interrupt to a CPU/VP. This ensures that the effective affinity mask
is always valid, not just after explicitly setting affinity.
2) Using an interrupt's effective affinity when unmasking it, which
prevents gic_unmask_irq() from unintentionally changing which
pcpu_mask includes an interrupt.
Fixes: 7778c4b27c ("irqchip: mips-gic: Use pcpu_masks to avoid reading GIC_SH_MASK*")
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: https://lkml.kernel.org/r/20170922062440.23701-3-paul.burton@imgtec.com
The MIPS GIC driver is incorrectly using __fls to shift registers,
intending to shift to the least significant bit of a value based upon
its mask but instead shifting off all but the value's top bit. It should
actually be using __ffs to shift to the first, not last, bit of the
value.
Apparently the system I used when testing commit 3680746abd
("irqchip: mips-gic: Convert remaining shared reg access to new
accessors") and commit b2b2e584ce ("irqchip: mips-gic: Clean up mti,
reserved-cpu-vectors handling") managed to work correctly despite this
issue, but not all systems do...
Fixes: 3680746abd ("irqchip: mips-gic: Convert remaining shared reg access to new accessors")
Fixes: b2b2e584ce ("irqchip: mips-gic: Clean up mti, reserved-cpu-vectors handling")
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: https://lkml.kernel.org/r/20170922062440.23701-2-paul.burton@imgtec.com
The write_gic_smask() & write_gic_rmask() functions take a shared
interrupt number as a parameter, but we're incorrectly providing them a
bitmask with the shared interrupt's bit set. This effectively means that
we mask or unmask the shared interrupt 1<<n rather than shared interrupt
n, and as a result likely drop interrupts.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Fixes: 68898c8765f4 ("irqchip: mips-gic: Drop gic_(re)set_mask() functions")
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
gcc-4.5 and earlier don't like named initializers for anonymous
union members:
drivers/irqchip/irq-gic-v4.c: In function 'its_map_vlpi':
drivers/irqchip/irq-gic-v4.c:176:3: error: unknown field 'map' specified in initializer
drivers/irqchip/irq-gic-v4.c:176:3: error: missing braces around initializer
drivers/irqchip/irq-gic-v4.c:176:3: error: (near initialization for 'info.<anonymous>')
drivers/irqchip/irq-gic-v4.c: In function 'its_get_vlpi':
drivers/irqchip/irq-gic-v4.c:192:3: error: unknown field 'map' specified in initializer
drivers/irqchip/irq-gic-v4.c:192:3: error: missing braces around initializer
drivers/irqchip/irq-gic-v4.c:192:3: error: (near initialization for 'info.<anonymous>')
drivers/irqchip/irq-gic-v4.c: In function 'its_prop_update_vlpi':
drivers/irqchip/irq-gic-v4.c:208:3: error: unknown field 'config' specified in initializer
drivers/irqchip/irq-gic-v4.c:208:3: error: missing braces around initializer
drivers/irqchip/irq-gic-v4.c:208:3: error: (near initialization for 'info.<anonymous>')
drivers/irqchip/irq-gic-v4.c:208:3: error: initialization makes pointer from integer without a cast
This is fairly easy to work around, by using extra curly braces.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
get_cpu_number() doesn't use existing helper to iterate over possible
CPUs, It will cause an error in case of discontinuous @cpu_possible_mask
such as 0b11110001, which can result from a core having failed to come
up on a SMP machine.
Fixed by using existing helper for_each_possible_cpu().
Signed-off-by: zijun_hu <zijun_hu@htc.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for 4.14 for MIPS; below a summary of
the non-merge commits:
CM:
- Rename mips_cm_base to mips_gcr_base
- Specify register size when generating accessors
- Use BIT/GENMASK for register fields, order & drop shifts
- Add cluster & block args to mips_cm_lock_other()
CPC:
- Use common CPS accessor generation macros
- Use BIT/GENMASK for register fields, order & drop shifts
- Introduce register modify (set/clear/change) accessors
- Use change_*, set_* & clear_* where appropriate
- Add CM/CPC 3.5 register definitions
- Use GlobalNumber macros rather than magic numbers
- Have asm/mips-cps.h include CM & CPC headers
- Cluster support for topology functions
- Detect CPUs in secondary clusters
CPS:
- Read GIC_VL_IDENT directly, not via irqchip driver
DMA:
- Consolidate coherent and non-coherent dma_alloc code
- Don't use dma_cache_sync to implement fd_cacheflush
FPU emulation / FP assist code:
- Another series of 14 commits fixing corner cases such as NaN
propgagation and other special input values.
- Zero bits 32-63 of the result for a CLASS.D instruction.
- Enhanced statics via debugfs
- Do not use bools for arithmetic. GCC 7.1 moans about this.
- Correct user fault_addr type
Generic MIPS:
- Enhancement of stack backtraces
- Cleanup from non-existing options
- Handle non word sized instructions when examining frame
- Fix detection and decoding of ADDIUSP instruction
- Fix decoding of SWSP16 instruction
- Refactor handling of stack pointer in get_frame_info
- Remove unreachable code from force_fcr31_sig()
- Convert to using %pOF instead of full_name
- Remove the R6000 support.
- Move FP code from *_switch.S to *_fpu.S
- Remove unused ST_OFF from r2300_switch.S
- Allow platform to specify multiple its.S files
- Add #includes to various files to ensure code builds reliable and
without warning..
- Remove __invalidate_kernel_vmap_range
- Remove plat_timer_setup
- Declare various variables & functions static
- Abstract CPU core & VP(E) ID access through accessor functions
- Store core & VP IDs in GlobalNumber-style variable
- Unify checks for sibling CPUs
- Add CPU cluster number accessors
- Prevent direct use of generic_defconfig
- Make CONFIG_MIPS_MT_SMP default y
- Add __ioread64_copy
- Remove unnecessary inclusions of linux/irqchip/mips-gic.h
GIC:
- Introduce asm/mips-gic.h with accessor functions
- Use new GIC accessor functions in mips-gic-timer
- Remove counter access functions from irq-mips-gic.c
- Remove gic_read_local_vp_id() from irq-mips-gic.c
- Simplify shared interrupt pending/mask reads in irq-mips-gic.c
- Simplify gic_local_irq_domain_map() in irq-mips-gic.c
- Drop gic_(re)set_mask() functions in irq-mips-gic.c
- Remove gic_set_polarity(), gic_set_trigger(), gic_set_dual_edge(),
gic_map_to_pin() and gic_map_to_vpe() from irq-mips-gic.c.
- Convert remaining shared reg access, local int mask access and
remaining local reg access to new accessors
- Move GIC_LOCAL_INT_* to asm/mips-gic.h
- Remove GIC_CPU_INT* macros from irq-mips-gic.c
- Move various definitions to the driver
- Remove gic_get_usm_range()
- Remove __gic_irq_dispatch() forward declaration
- Remove gic_init()
- Use mips_gic_present() in place of gic_present and remove
gic_present
- Move gic_get_c0_*_int() to asm/mips-gic.h
- Remove linux/irqchip/mips-gic.h
- Inline __gic_init()
- Inline gic_basic_init()
- Make pcpu_masks a per-cpu variable
- Use pcpu_masks to avoid reading GIC_SH_MASK*
- Clean up mti, reserved-cpu-vectors handling
- Use cpumask_first_and() in gic_set_affinity()
- Let the core set struct irq_common_data affinity
microMIPS:
- Fix microMIPS stack unwinding on big endian systems
MIPS-GIC:
- SYNC after enabling GIC region
NUMA:
- Remove the unused parent_node() macro
R6:
- Constify r2_decoder_tables
- Add accessor & bit definitions for GlobalNumber
SMP:
- Constify smp ops
- Allow boot_secondary SMP op to return errors
VDSO:
- Drop gic_get_usm_range() usage
- Avoid use of linux/irqchip/mips-gic.h
Platform changes:
Alchemy:
- Add devboard machine type to cpuinfo
- update cpu feature overrides
- Threaded carddetect irqs for devboards
AR7:
- allow NULL clock for clk_get_rate
BCM63xx:
- Fix ENETDMA_6345_MAXBURST_REG offset
- Allow NULL clock for clk_get_rate
CI20:
- Enable GPIO and RTC drivers in defconfig
- Add ethernet and fixed-regulator nodes to DTS
Generic platform:
- Move Boston and NI 169445 FIT image source to their own files
- Include asm/bootinfo.h for plat_fdt_relocated()
- Include asm/time.h for get_c0_*_int()
- Include asm/bootinfo.h for plat_fdt_relocated()
- Include asm/time.h for get_c0_*_int()
- Allow filtering enabled boards by requirements
- Don't explicitly disable CONFIG_USB_SUPPORT
- Bump default NR_CPUS to 16
JZ4700:
- Probe the jz4740-rtc driver from devicetree
Lantiq:
- Drop check of boot select from the spi-falcon driver.
- Drop check of boot select from the lantiq-flash MTD driver.
- Access boot cause register in the watchdog driver through regmap
- Add device tree binding documentation for the watchdog driver
- Add docs for the RCU DT bindings.
- Convert the fpi bus driver to a platform_driver
- Remove ltq_reset_cause() and ltq_boot_select(
- Switch to a proper reset driver
- Switch to a new drivers/soc GPHY driver
- Add an USB PHY driver for the Lantiq SoCs using the RCU module
- Use of_platform_default_populate instead of __dt_register_buses
- Enable MFD_SYSCON to be able to use it for the RCU MFD
- Replace ltq_boot_select() with dummy implementation.
Loongson 2F:
- Allow NULL clock for clk_get_rate
Malta:
- Use new GIC accessor functions
NI 169445:
- Add support for NI 169445 board.
- Only include in 32r2el kernels
Octeon:
- Add support for watchdog of 78XX SOCs.
- Add support for watchdog of CN68XX SOCs.
- Expose support for mips32r1, mips32r2 and mips64r1
- Enable more drivers in config file
- Add support for accessing the boot vector.
- Remove old boot vector code from watchdog driver
- Define watchdog registers for 70xx, 73xx, 78xx, F75xx.
- Make CSR functions node aware.
- Allow access to CIU3 IRQ domains.
- Misc cleanups in the watchdog driver
Omega2+:
- New board, add support and defconfig
Pistachio:
- Enable Root FS on NFS in defconfig
Ralink:
- Add Mediatek MT7628A SoC
- Allow NULL clock for clk_get_rate
- Explicitly request exclusive reset control in the pci-mt7620 PCI driver.
SEAD3:
- Only include in 32 bit kernels by default
VoCore:
- Add VoCore as a vendor t0 dt-bindings
- Add defconfig file"
* '4.14-features' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (167 commits)
MIPS: Refactor handling of stack pointer in get_frame_info
MIPS: Stacktrace: Fix microMIPS stack unwinding on big endian systems
MIPS: microMIPS: Fix decoding of swsp16 instruction
MIPS: microMIPS: Fix decoding of addiusp instruction
MIPS: microMIPS: Fix detection of addiusp instruction
MIPS: Handle non word sized instructions when examining frame
MIPS: ralink: allow NULL clock for clk_get_rate
MIPS: Loongson 2F: allow NULL clock for clk_get_rate
MIPS: BCM63XX: allow NULL clock for clk_get_rate
MIPS: AR7: allow NULL clock for clk_get_rate
MIPS: BCM63XX: fix ENETDMA_6345_MAXBURST_REG offset
mips: Save all registers when saving the frame
MIPS: Add DWARF unwinding to assembly
MIPS: Make SAVE_SOME more standard
MIPS: Fix issues in backtraces
MIPS: jz4780: DTS: Probe the jz4740-rtc driver from devicetree
MIPS: Ci20: Enable RTC driver
watchdog: octeon-wdt: Add support for 78XX SOCs.
watchdog: octeon-wdt: Add support for cn68XX SOCs.
watchdog: octeon-wdt: File cleaning.
...
Pull irq updates from Thomas Gleixner:
"The interrupt subsystem delivers this time:
- Refactoring of the GIC-V3 driver to prepare for the GIC-V4 support
- Initial GIC-V4 support
- Consolidation of the FSL MSI support
- Utilize the effective affinity interface in various ARM irqchip
drivers
- Yet another interrupt chip driver (UniPhier AIDET)
- Bulk conversion of the irq chip driver to use %pOF
- The usual small fixes and improvements all over the place"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (77 commits)
irqchip/ls-scfg-msi: Add MSI affinity support
irqchip/ls-scfg-msi: Add LS1043a v1.1 MSI support
irqchip/ls-scfg-msi: Add LS1046a MSI support
arm64: dts: ls1046a: Add MSI dts node
arm64: dts: ls1043a: Share all MSIs
arm: dts: ls1021a: Share all MSIs
arm64: dts: ls1043a: Fix typo of MSI compatible string
arm: dts: ls1021a: Fix typo of MSI compatible string
irqchip/ls-scfg-msi: Fix typo of MSI compatible strings
irqchip/irq-bcm7120-l2: Use correct I/O accessors for irq_fwd_mask
irqchip/mmp: Make mmp_intc_conf const
irqchip/gic: Make irq_chip const
irqchip/gic-v3: Advertise GICv4 support to KVM
irqchip/gic-v4: Enable low-level GICv4 operations
irqchip/gic-v4: Add some basic documentation
irqchip/gic-v4: Add VLPI configuration interface
irqchip/gic-v4: Add VPE command interface
irqchip/gic-v4: Add per-VM VPE domain creation
irqchip/gic-v3-its: Set implementation defined bit to enable VLPIs
irqchip/gic-v3-its: Allow doorbell interrupts to be injected/cleared
...
gic_set_affinity() manually copies the provided cpumask to the struct
irq_common_data affinity field, returning IRQ_SET_MASK_OK_NOCOPY in
order to prevent the core code from doing that.
We can instead simply let the core code do it for us, by returning
IRQ_SET_MASK_OK instead of IRQ_SET_MASK_OK_NOCOPY & doing the copy
ourselves.
[ralf@linux-mips.org: Resolve merge conflict.]
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17056/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Currently in gic_set_affinity() we calculate a temporary cpumask holding
the intersection of the provided cpumask & the CPUs that are online,
then we call cpumask_first twice on it to find the first such CPU. Since
we don't need the temporary cpumask for anything else & we only care
about the first CPU that's both online & in the provided cpumask, we can
instead use cpumask_first_and to find that CPU & drop the temporary
mask.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17110/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When parsing mti,reserved-cpu-vectors we generate a mask of all bits
that have been declared reserved, the loop through starting from bit 2
to find one that isn't reserved (ie. is zero).
This patch accomplishes the same task more simply by:
- Inititialising the reserved mask to 0x3 (ie. the 2 software
interrupts). This means we don't need to skip them later as the loop
previously has.
- Replacing the loop checking for zero bits with find_first_zero_bit,
which fits our needs now that the 2 software interrupts are marked
reserved. This requires that the type of reserved is changed to
unsigned long so that it's suitable for use with bitmap functions.
- Replacing the magic number 8 with the hamming weight of the ST0_IM
field - ie. the number of bits that a MIPS CPU has for interrupt
inputs. This is still a compile-time constant 8, but makes it
clearer why it's 8.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17054/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch avoids the need to read the GIC_SH_MASK* registers when
decoding shared interrupts by setting & clearing the interrupt's bit in
the appropriate CPU's pcpu_masks entry when masking or unmasking the
interrupt.
This effectively means that whilst an interrupt is masked we clear its
bit in all pcpu_masks, which causes gic_handle_shared_int() to ignore it
on all CPUs without needing to check GIC_SH_MASK*.
In essence, we add a little overhead to masking or unmasking interrupts
but in return reduce the overhead of the far more common task of
decoding interrupts.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17109/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Define the pcpu_masks variable using the kernel's standard per-cpu
variable support, rather than an open-coded array of structs containing
bitmaps.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17052/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
gic_basic_init() is now a fairly short function that is only called in
one place. Inline it into gic_of_init() to help readability.
[ralf@linux-mips.org: Resolved conflict.]
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17051/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The __gic_init() function is only called from gic_of_init() now that the
non-DT path has been removed. In order to simplify the code & aid
readability, fold __gic_init() into gic_of_init().
This provides us with the ability to return an error code, which
__gic_init() was previously unable to do. As such the irq_domain_add_*()
error paths are modified to print & return an error rather than panic().
[ralf@linux-mips.org: Resoled reject.]
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17050/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Marc Zyngier