This is a driver for the Integrated Silicon Solution Inc. LED driver
chips series IS31FL319x. They can drive 1, 3, 6 or up to 9
LEDs.
Each LED is individually controllable in brightness (through pwm)
in 256 steps so that RGB LEDs can show any of ca. 16 Mio colors.
The maximum current of the LEDs can be programmed and limited to
5 .. 40mA through a device tree property.
The chip is connected through I2C and can have one of 4 addresses
in the range 0x64 .. 0x67 depending on how the AD pin is connected. The
address is defined by the reg property as usual.
The chip also has a shutdown input which could be connected to a GPIO,
but this driver uses software shutdown if all LEDs are inactivated.
The chip also has breathing and audio features which are not fully
supported by this driver.
Tested-on: OMAP5 based Pyra handheld prototype.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Andrey Utkin <andrey_utkin@fastmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Highlights:
- PowerNV PCI hotplug support.
- Lots more Power9 support.
- eBPF JIT support on ppc64le.
- Lots of cxl updates.
- Boot code consolidation.
Bug fixes:
- Fix spin_unlock_wait() from Boqun Feng
- Fix stack pointer corruption in __tm_recheckpoint() from Michael Neuling
- Fix multiple bugs in memory_hotplug_max() from Bharata B Rao
- mm: Ensure "special" zones are empty from Oliver O'Halloran
- ftrace: Separate the heuristics for checking call sites from Michael Ellerman
- modules: Never restore r2 for a mprofile-kernel style mcount() call from Michael Ellerman
- Fix endianness when reading TCEs from Alexey Kardashevskiy
- start rtasd before PCI probing from Greg Kurz
- PCI: rpaphp: Fix slot registration for multiple slots under a PHB from Tyrel Datwyler
- powerpc/mm: Add memory barrier in __hugepte_alloc() from Sukadev Bhattiprolu
Cleanups & fixes:
- Drop support for MPIC in pseries from Rashmica Gupta
- Define and use PPC64_ELF_ABI_v2/v1 from Michael Ellerman
- Remove unused symbols in asm-offsets.c from Rashmica Gupta
- Fix SRIOV not building without EEH enabled from Russell Currey
- Remove kretprobe_trampoline_holder. from Thiago Jung Bauermann
- Reduce log level of PCI I/O space warning from Benjamin Herrenschmidt
- Add array bounds checking to crash_shutdown_handlers from Suraj Jitindar Singh
- Avoid -maltivec when using clang integrated assembler from Anton Blanchard
- Fix array overrun in ppc_rtas() syscall from Andrew Donnellan
- Fix error return value in cmm_mem_going_offline() from Rasmus Villemoes
- export cpu_to_core_id() from Mauricio Faria de Oliveira
- Remove old symbols from defconfigs from Andrew Donnellan
- Update obsolete comments in setup_32.c about entry conditions from Benjamin Herrenschmidt
- Add comment explaining the purpose of setup_kdump_trampoline() from Benjamin Herrenschmidt
- Merge the RELOCATABLE config entries for ppc32 and ppc64 from Kevin Hao
- Remove RELOCATABLE_PPC32 from Kevin Hao
- Fix .long's in tlb-radix.c to more meaningful from Balbir Singh
Minor cleanups & fixes:
- Andrew Donnellan, Anna-Maria Gleixner, Anton Blanchard, Benjamin
Herrenschmidt, Bharata B Rao, Christophe Leroy, Colin Ian King, Geliang
Tang, Greg Kurz, Madhavan Srinivasan, Michael Ellerman, Michael Ellerman,
Stephen Rothwell, Stewart Smith.
Freescale updates from Scott:
- "Highlights include more 8xx optimizations, device tree updates,
and MVME7100 support."
PowerNV PCI hotplug from Gavin Shan:
- PCI: Add pcibios_setup_bridge()
- Override pcibios_setup_bridge()
- Remove PCI_RESET_DELAY_US
- Move pnv_pci_ioda_setup_opal_tce_kill() around
- Increase PE# capacity
- Allocate PE# in reverse order
- Create PEs in pcibios_setup_bridge()
- Setup PE for root bus
- Extend PCI bridge resources
- Make pnv_ioda_deconfigure_pe() visible
- Dynamically release PE
- Update bridge windows on PCI plug
- Delay populating pdn
- Support PCI slot ID
- Use PCI slot reset infrastructure
- Introduce pnv_pci_get_slot_id()
- Functions to get/set PCI slot state
- PCI/hotplug: PowerPC PowerNV PCI hotplug driver
- Print correct PHB type names
Power9 idle support from Shreyas B. Prabhu:
- set power_save func after the idle states are initialized
- Use PNV_THREAD_WINKLE macro while requesting for winkle
- make hypervisor state restore a function
- Rename idle_power7.S to idle_book3s.S
- Rename reusable idle functions to hardware agnostic names
- Make pnv_powersave_common more generic
- abstraction for saving SPRs before entering deep idle states
- Add platform support for stop instruction
- cpuidle/powernv: Use CPUIDLE_STATE_MAX instead of MAX_POWERNV_IDLE_STATES
- cpuidle/powernv: cleanup cpuidle-powernv.c
- cpuidle/powernv: Add support for POWER ISA v3 idle states
- Use deepest stop state when cpu is offlined
Power9 PMU from Madhavan Srinivasan:
- factor out power8 pmu macros and defines
- factor out power8 pmu functions
- factor out power8 __init_pmu code
- Add power9 event list macros for generic and cache events
- Power9 PMU support
- Export Power9 generic and cache events to sysfs
Power9 preliminary interrupt & PCI support from Benjamin Herrenschmidt:
- Add XICS emulation APIs
- Move a few exception common handlers to make room
- Add support for HV virtualization interrupts
- Add mechanism to force a replay of interrupts
- Add ICP OPAL backend
- Discover IODA3 PHBs
- pci: Remove obsolete SW invalidate
- opal: Add real mode call wrappers
- Rename TCE invalidation calls
- Remove SWINV constants and obsolete TCE code
- Rework accessing the TCE invalidate register
- Fallback to OPAL for TCE invalidations
- Use the device-tree to get available range of M64's
- Check status of a PHB before using it
- pci: Don't try to allocate resources that will be reassigned
Other Power9:
- Send SIGBUS on unaligned copy and paste from Chris Smart
- Large Decrementer support from Oliver O'Halloran
- Load Monitor Register Support from Jack Miller
Performance improvements from Anton Blanchard:
- Avoid load hit store in __giveup_fpu() and __giveup_altivec()
- Avoid load hit store in setup_sigcontext()
- Remove assembly versions of strcpy, strcat, strlen and strcmp
- Align hot loops of some string functions
eBPF JIT from Naveen N. Rao:
- Fix/enhance 32-bit Load Immediate implementation
- Optimize 64-bit Immediate loads
- Introduce rotate immediate instructions
- A few cleanups
- Isolate classic BPF JIT specifics into a separate header
- Implement JIT compiler for extended BPF
Operator Panel driver from Suraj Jitindar Singh:
- devicetree/bindings: Add binding for operator panel on FSP machines
- Add inline function to get rc from an ASYNC_COMP opal_msg
- Add driver for operator panel on FSP machines
Sparse fixes from Daniel Axtens:
- make some things static
- Introduce asm-prototypes.h
- Include headers containing prototypes
- Use #ifdef __BIG_ENDIAN__ #else for REG_BYTE
- kvm: Clarify __user annotations
- Pass endianness to sparse
- Make ppc_md.{halt, restart} __noreturn
MM fixes & cleanups from Aneesh Kumar K.V:
- radix: Update LPCR HR bit as per ISA
- use _raw variant of page table accessors
- Compile out radix related functions if RADIX_MMU is disabled
- Clear top 16 bits of va only on older cpus
- Print formation regarding the the MMU mode
- hash: Update SDR1 size encoding as documented in ISA 3.0
- radix: Update PID switch sequence
- radix: Update machine call back to support new HCALL.
- radix: Add LPID based tlb flush helpers
- radix: Add a kernel command line to disable radix
- Cleanup LPCR defines
Boot code consolidation from Benjamin Herrenschmidt:
- Move epapr_paravirt_early_init() to early_init_devtree()
- cell: Don't use flat device-tree after boot
- ge_imp3a: Don't use the flat device-tree after boot
- mpc85xx_ds: Don't use the flat device-tree after boot
- mpc85xx_rdb: Don't use the flat device-tree after boot
- Don't test for machine type in rtas_initialize()
- Don't test for machine type in smp_setup_cpu_maps()
- dt: Add of_device_compatible_match()
- Factor do_feature_fixup calls
- Move 64-bit feature fixup earlier
- Move 64-bit memory reserves to setup_arch()
- Use a cachable DART
- Move FW feature probing out of pseries probe()
- Put exception configuration in a common place
- Remove early allocation of the SMU command buffer
- Move MMU backend selection out of platform code
- pasemi: Remove IOBMAP allocation from platform probe()
- mm/hash: Don't use machine_is() early during boot
- Don't test for machine type to detect HEA special case
- pmac: Remove spurrious machine type test
- Move hash table ops to a separate structure
- Ensure that ppc_md is empty before probing for machine type
- Move 64-bit probe_machine() to later in the boot process
- Move 32-bit probe() machine to later in the boot process
- Get rid of ppc_md.init_early()
- Move the boot time info banner to a separate function
- Move setting of {i,d}cache_bsize to initialize_cache_info()
- Move the content of setup_system() to setup_arch()
- Move cache info inits to a separate function
- Re-order the call to smp_setup_cpu_maps()
- Re-order setup_panic()
- Make a few boot functions __init
- Merge 32-bit and 64-bit setup_arch()
Other new features:
- tty/hvc: Use IRQF_SHARED for OPAL hvc consoles from Sam Mendoza-Jonas
- tty/hvc: Use opal irqchip interface if available from Sam Mendoza-Jonas
- powerpc: Add module autoloading based on CPU features from Alastair D'Silva
- crypto: vmx - Convert to CPU feature based module autoloading from Alastair D'Silva
- Wake up kopald polling thread before waiting for events from Benjamin Herrenschmidt
- xmon: Dump ISA 2.06 SPRs from Michael Ellerman
- xmon: Dump ISA 2.07 SPRs from Michael Ellerman
- Add a parameter to disable 1TB segs from Oliver O'Halloran
- powerpc/boot: Add OPAL console to epapr wrappers from Oliver O'Halloran
- Assign fixed PHB number based on device-tree properties from Guilherme G. Piccoli
- pseries: Add pseries hotplug workqueue from John Allen
- pseries: Add support for hotplug interrupt source from John Allen
- pseries: Use kernel hotplug queue for PowerVM hotplug events from John Allen
- pseries: Move property cloning into its own routine from Nathan Fontenot
- pseries: Dynamic add entires to associativity lookup array from Nathan Fontenot
- pseries: Auto-online hotplugged memory from Nathan Fontenot
- pseries: Remove call to memblock_add() from Nathan Fontenot
cxl:
- Add set and get private data to context struct from Michael Neuling
- make base more explicitly non-modular from Paul Gortmaker
- Use for_each_compatible_node() macro from Wei Yongjun
- Frederic Barrat
- Abstract the differences between the PSL and XSL
- Make vPHB device node match adapter's
- Philippe Bergheaud
- Add mechanism for delivering AFU driver specific events
- Ignore CAPI adapters misplaced in switched slots
- Refine slice error debug messages
- Andrew Donnellan
- static-ify variables to fix sparse warnings
- PCI/hotplug: pnv_php: export symbols and move struct types needed by cxl
- PCI/hotplug: pnv_php: handle OPAL_PCI_SLOT_OFFLINE power state
- Add cxl_check_and_switch_mode() API to switch bi-modal cards
- remove dead Kconfig options
- fix potential NULL dereference in free_adapter()
- Ian Munsie
- Update process element after allocating interrupts
- Add support for CAPP DMA mode
- Fix allowing bogus AFU descriptors with 0 maximum processes
- Fix allocating a minimum of 2 pages for the SPA
- Fix bug where AFU disable operation had no effect
- Workaround XSL bug that does not clear the RA bit after a reset
- Fix NULL pointer dereference on kernel contexts with no AFU interrupts
- powerpc/powernv: Split cxl code out into a separate file
- Add cxl_slot_is_supported API
- Enable bus mastering for devices using CAPP DMA mode
- Move cxl_afu_get / cxl_afu_put to base
- Allow a default context to be associated with an external pci_dev
- Do not create vPHB if there are no AFU configuration records
- powerpc/powernv: Add support for the cxl kernel api on the real phb
- Add support for using the kernel API with a real PHB
- Add kernel APIs to get & set the max irqs per context
- Add preliminary workaround for CX4 interrupt limitation
- Add support for interrupts on the Mellanox CX4
- Workaround PE=0 hardware limitation in Mellanox CX4
- powerpc/powernv: Fix pci-cxl.c build when CONFIG_MODULES=n
selftests:
- Test unaligned copy and paste from Chris Smart
- Load Monitor Register Tests from Jack Miller
- Cyril Bur
- exec() with suspended transaction
- Use signed long to read perf_event_paranoid
- Fix usage message in context_switch
- Fix generation of vector instructions/types in context_switch
- Michael Ellerman
- Use "Delta" rather than "Error" in normal output
- Import Anton's mmap & futex micro benchmarks
- Add a test for PROT_SAO
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Z5kM
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Highlights:
- PowerNV PCI hotplug support.
- Lots more Power9 support.
- eBPF JIT support on ppc64le.
- Lots of cxl updates.
- Boot code consolidation.
Bug fixes:
- Fix spin_unlock_wait() from Boqun Feng
- Fix stack pointer corruption in __tm_recheckpoint() from Michael
Neuling
- Fix multiple bugs in memory_hotplug_max() from Bharata B Rao
- mm: Ensure "special" zones are empty from Oliver O'Halloran
- ftrace: Separate the heuristics for checking call sites from
Michael Ellerman
- modules: Never restore r2 for a mprofile-kernel style mcount() call
from Michael Ellerman
- Fix endianness when reading TCEs from Alexey Kardashevskiy
- start rtasd before PCI probing from Greg Kurz
- PCI: rpaphp: Fix slot registration for multiple slots under a PHB
from Tyrel Datwyler
- powerpc/mm: Add memory barrier in __hugepte_alloc() from Sukadev
Bhattiprolu
Cleanups & fixes:
- Drop support for MPIC in pseries from Rashmica Gupta
- Define and use PPC64_ELF_ABI_v2/v1 from Michael Ellerman
- Remove unused symbols in asm-offsets.c from Rashmica Gupta
- Fix SRIOV not building without EEH enabled from Russell Currey
- Remove kretprobe_trampoline_holder from Thiago Jung Bauermann
- Reduce log level of PCI I/O space warning from Benjamin
Herrenschmidt
- Add array bounds checking to crash_shutdown_handlers from Suraj
Jitindar Singh
- Avoid -maltivec when using clang integrated assembler from Anton
Blanchard
- Fix array overrun in ppc_rtas() syscall from Andrew Donnellan
- Fix error return value in cmm_mem_going_offline() from Rasmus
Villemoes
- export cpu_to_core_id() from Mauricio Faria de Oliveira
- Remove old symbols from defconfigs from Andrew Donnellan
- Update obsolete comments in setup_32.c about entry conditions from
Benjamin Herrenschmidt
- Add comment explaining the purpose of setup_kdump_trampoline() from
Benjamin Herrenschmidt
- Merge the RELOCATABLE config entries for ppc32 and ppc64 from Kevin
Hao
- Remove RELOCATABLE_PPC32 from Kevin Hao
- Fix .long's in tlb-radix.c to more meaningful from Balbir Singh
Minor cleanups & fixes:
- Andrew Donnellan, Anna-Maria Gleixner, Anton Blanchard, Benjamin
Herrenschmidt, Bharata B Rao, Christophe Leroy, Colin Ian King,
Geliang Tang, Greg Kurz, Madhavan Srinivasan, Michael Ellerman,
Michael Ellerman, Stephen Rothwell, Stewart Smith.
Freescale updates from Scott:
- "Highlights include more 8xx optimizations, device tree updates,
and MVME7100 support."
PowerNV PCI hotplug from Gavin Shan:
- PCI: Add pcibios_setup_bridge()
- Override pcibios_setup_bridge()
- Remove PCI_RESET_DELAY_US
- Move pnv_pci_ioda_setup_opal_tce_kill() around
- Increase PE# capacity
- Allocate PE# in reverse order
- Create PEs in pcibios_setup_bridge()
- Setup PE for root bus
- Extend PCI bridge resources
- Make pnv_ioda_deconfigure_pe() visible
- Dynamically release PE
- Update bridge windows on PCI plug
- Delay populating pdn
- Support PCI slot ID
- Use PCI slot reset infrastructure
- Introduce pnv_pci_get_slot_id()
- Functions to get/set PCI slot state
- PCI/hotplug: PowerPC PowerNV PCI hotplug driver
- Print correct PHB type names
Power9 idle support from Shreyas B. Prabhu:
- set power_save func after the idle states are initialized
- Use PNV_THREAD_WINKLE macro while requesting for winkle
- make hypervisor state restore a function
- Rename idle_power7.S to idle_book3s.S
- Rename reusable idle functions to hardware agnostic names
- Make pnv_powersave_common more generic
- abstraction for saving SPRs before entering deep idle states
- Add platform support for stop instruction
- cpuidle/powernv: Use CPUIDLE_STATE_MAX instead of MAX_POWERNV_IDLE_STATES
- cpuidle/powernv: cleanup cpuidle-powernv.c
- cpuidle/powernv: Add support for POWER ISA v3 idle states
- Use deepest stop state when cpu is offlined
Power9 PMU from Madhavan Srinivasan:
- factor out power8 pmu macros and defines
- factor out power8 pmu functions
- factor out power8 __init_pmu code
- Add power9 event list macros for generic and cache events
- Power9 PMU support
- Export Power9 generic and cache events to sysfs
Power9 preliminary interrupt & PCI support from Benjamin Herrenschmidt:
- Add XICS emulation APIs
- Move a few exception common handlers to make room
- Add support for HV virtualization interrupts
- Add mechanism to force a replay of interrupts
- Add ICP OPAL backend
- Discover IODA3 PHBs
- pci: Remove obsolete SW invalidate
- opal: Add real mode call wrappers
- Rename TCE invalidation calls
- Remove SWINV constants and obsolete TCE code
- Rework accessing the TCE invalidate register
- Fallback to OPAL for TCE invalidations
- Use the device-tree to get available range of M64's
- Check status of a PHB before using it
- pci: Don't try to allocate resources that will be reassigned
Other Power9:
- Send SIGBUS on unaligned copy and paste from Chris Smart
- Large Decrementer support from Oliver O'Halloran
- Load Monitor Register Support from Jack Miller
Performance improvements from Anton Blanchard:
- Avoid load hit store in __giveup_fpu() and __giveup_altivec()
- Avoid load hit store in setup_sigcontext()
- Remove assembly versions of strcpy, strcat, strlen and strcmp
- Align hot loops of some string functions
eBPF JIT from Naveen N. Rao:
- Fix/enhance 32-bit Load Immediate implementation
- Optimize 64-bit Immediate loads
- Introduce rotate immediate instructions
- A few cleanups
- Isolate classic BPF JIT specifics into a separate header
- Implement JIT compiler for extended BPF
Operator Panel driver from Suraj Jitindar Singh:
- devicetree/bindings: Add binding for operator panel on FSP machines
- Add inline function to get rc from an ASYNC_COMP opal_msg
- Add driver for operator panel on FSP machines
Sparse fixes from Daniel Axtens:
- make some things static
- Introduce asm-prototypes.h
- Include headers containing prototypes
- Use #ifdef __BIG_ENDIAN__ #else for REG_BYTE
- kvm: Clarify __user annotations
- Pass endianness to sparse
- Make ppc_md.{halt, restart} __noreturn
MM fixes & cleanups from Aneesh Kumar K.V:
- radix: Update LPCR HR bit as per ISA
- use _raw variant of page table accessors
- Compile out radix related functions if RADIX_MMU is disabled
- Clear top 16 bits of va only on older cpus
- Print formation regarding the the MMU mode
- hash: Update SDR1 size encoding as documented in ISA 3.0
- radix: Update PID switch sequence
- radix: Update machine call back to support new HCALL.
- radix: Add LPID based tlb flush helpers
- radix: Add a kernel command line to disable radix
- Cleanup LPCR defines
Boot code consolidation from Benjamin Herrenschmidt:
- Move epapr_paravirt_early_init() to early_init_devtree()
- cell: Don't use flat device-tree after boot
- ge_imp3a: Don't use the flat device-tree after boot
- mpc85xx_ds: Don't use the flat device-tree after boot
- mpc85xx_rdb: Don't use the flat device-tree after boot
- Don't test for machine type in rtas_initialize()
- Don't test for machine type in smp_setup_cpu_maps()
- dt: Add of_device_compatible_match()
- Factor do_feature_fixup calls
- Move 64-bit feature fixup earlier
- Move 64-bit memory reserves to setup_arch()
- Use a cachable DART
- Move FW feature probing out of pseries probe()
- Put exception configuration in a common place
- Remove early allocation of the SMU command buffer
- Move MMU backend selection out of platform code
- pasemi: Remove IOBMAP allocation from platform probe()
- mm/hash: Don't use machine_is() early during boot
- Don't test for machine type to detect HEA special case
- pmac: Remove spurrious machine type test
- Move hash table ops to a separate structure
- Ensure that ppc_md is empty before probing for machine type
- Move 64-bit probe_machine() to later in the boot process
- Move 32-bit probe() machine to later in the boot process
- Get rid of ppc_md.init_early()
- Move the boot time info banner to a separate function
- Move setting of {i,d}cache_bsize to initialize_cache_info()
- Move the content of setup_system() to setup_arch()
- Move cache info inits to a separate function
- Re-order the call to smp_setup_cpu_maps()
- Re-order setup_panic()
- Make a few boot functions __init
- Merge 32-bit and 64-bit setup_arch()
Other new features:
- tty/hvc: Use IRQF_SHARED for OPAL hvc consoles from Sam Mendoza-Jonas
- tty/hvc: Use opal irqchip interface if available from Sam Mendoza-Jonas
- powerpc: Add module autoloading based on CPU features from Alastair D'Silva
- crypto: vmx - Convert to CPU feature based module autoloading from Alastair D'Silva
- Wake up kopald polling thread before waiting for events from Benjamin Herrenschmidt
- xmon: Dump ISA 2.06 SPRs from Michael Ellerman
- xmon: Dump ISA 2.07 SPRs from Michael Ellerman
- Add a parameter to disable 1TB segs from Oliver O'Halloran
- powerpc/boot: Add OPAL console to epapr wrappers from Oliver O'Halloran
- Assign fixed PHB number based on device-tree properties from Guilherme G. Piccoli
- pseries: Add pseries hotplug workqueue from John Allen
- pseries: Add support for hotplug interrupt source from John Allen
- pseries: Use kernel hotplug queue for PowerVM hotplug events from John Allen
- pseries: Move property cloning into its own routine from Nathan Fontenot
- pseries: Dynamic add entires to associativity lookup array from Nathan Fontenot
- pseries: Auto-online hotplugged memory from Nathan Fontenot
- pseries: Remove call to memblock_add() from Nathan Fontenot
cxl:
- Add set and get private data to context struct from Michael Neuling
- make base more explicitly non-modular from Paul Gortmaker
- Use for_each_compatible_node() macro from Wei Yongjun
- Frederic Barrat
- Abstract the differences between the PSL and XSL
- Make vPHB device node match adapter's
- Philippe Bergheaud
- Add mechanism for delivering AFU driver specific events
- Ignore CAPI adapters misplaced in switched slots
- Refine slice error debug messages
- Andrew Donnellan
- static-ify variables to fix sparse warnings
- PCI/hotplug: pnv_php: export symbols and move struct types needed by cxl
- PCI/hotplug: pnv_php: handle OPAL_PCI_SLOT_OFFLINE power state
- Add cxl_check_and_switch_mode() API to switch bi-modal cards
- remove dead Kconfig options
- fix potential NULL dereference in free_adapter()
- Ian Munsie
- Update process element after allocating interrupts
- Add support for CAPP DMA mode
- Fix allowing bogus AFU descriptors with 0 maximum processes
- Fix allocating a minimum of 2 pages for the SPA
- Fix bug where AFU disable operation had no effect
- Workaround XSL bug that does not clear the RA bit after a reset
- Fix NULL pointer dereference on kernel contexts with no AFU interrupts
- powerpc/powernv: Split cxl code out into a separate file
- Add cxl_slot_is_supported API
- Enable bus mastering for devices using CAPP DMA mode
- Move cxl_afu_get / cxl_afu_put to base
- Allow a default context to be associated with an external pci_dev
- Do not create vPHB if there are no AFU configuration records
- powerpc/powernv: Add support for the cxl kernel api on the real phb
- Add support for using the kernel API with a real PHB
- Add kernel APIs to get & set the max irqs per context
- Add preliminary workaround for CX4 interrupt limitation
- Add support for interrupts on the Mellanox CX4
- Workaround PE=0 hardware limitation in Mellanox CX4
- powerpc/powernv: Fix pci-cxl.c build when CONFIG_MODULES=n
selftests:
- Test unaligned copy and paste from Chris Smart
- Load Monitor Register Tests from Jack Miller
- Cyril Bur
- exec() with suspended transaction
- Use signed long to read perf_event_paranoid
- Fix usage message in context_switch
- Fix generation of vector instructions/types in context_switch
- Michael Ellerman
- Use "Delta" rather than "Error" in normal output
- Import Anton's mmap & futex micro benchmarks
- Add a test for PROT_SAO"
* tag 'powerpc-4.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (263 commits)
powerpc/mm: Parenthesise IS_ENABLED() in if condition
tty/hvc: Use opal irqchip interface if available
tty/hvc: Use IRQF_SHARED for OPAL hvc consoles
selftests/powerpc: exec() with suspended transaction
powerpc: Improve comment explaining why we modify VRSAVE
powerpc/mm: Drop unused externs for hpte_init_beat[_v3]()
powerpc/mm: Rename hpte_init_lpar() and move the fallback to a header
powerpc/mm: Fix build break when PPC_NATIVE=n
crypto: vmx - Convert to CPU feature based module autoloading
powerpc: Add module autoloading based on CPU features
powerpc/powernv/ioda: Fix endianness when reading TCEs
powerpc/mm: Add memory barrier in __hugepte_alloc()
powerpc/modules: Never restore r2 for a mprofile-kernel style mcount() call
powerpc/ftrace: Separate the heuristics for checking call sites
powerpc: Merge 32-bit and 64-bit setup_arch()
powerpc/64: Make a few boot functions __init
powerpc: Re-order setup_panic()
powerpc: Re-order the call to smp_setup_cpu_maps()
powerpc/32: Move cache info inits to a separate function
powerpc/64: Move the content of setup_system() to setup_arch()
...
Pull smp hotplug updates from Thomas Gleixner:
"This is the next part of the hotplug rework.
- Convert all notifiers with a priority assigned
- Convert all CPU_STARTING/DYING notifiers
The final removal of the STARTING/DYING infrastructure will happen
when the merge window closes.
Another 700 hundred line of unpenetrable maze gone :)"
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (70 commits)
timers/core: Correct callback order during CPU hot plug
leds/trigger/cpu: Move from CPU_STARTING to ONLINE level
powerpc/numa: Convert to hotplug state machine
arm/perf: Fix hotplug state machine conversion
irqchip/armada: Avoid unused function warnings
ARC/time: Convert to hotplug state machine
clocksource/atlas7: Convert to hotplug state machine
clocksource/armada-370-xp: Convert to hotplug state machine
clocksource/exynos_mct: Convert to hotplug state machine
clocksource/arm_global_timer: Convert to hotplug state machine
rcu: Convert rcutree to hotplug state machine
KVM/arm/arm64/vgic-new: Convert to hotplug state machine
smp/cfd: Convert core to hotplug state machine
x86/x2apic: Convert to CPU hotplug state machine
profile: Convert to hotplug state machine
timers/core: Convert to hotplug state machine
hrtimer: Convert to hotplug state machine
x86/tboot: Convert to hotplug state machine
arm64/armv8 deprecated: Convert to hotplug state machine
hwtracing/coresight-etm4x: Convert to hotplug state machine
...
There is no need the ledtriger to be called *that* early in the hotplug
process (+ with disabled interrupts). As explained by Jacek Anaszewski [0]
there is no need for it.
Therefore this patch moves it to the ONLINE/PREPARE_DOWN level using the
dynamic registration for the id.
[0] https://lkml.kernel.org/r/578C92BC.2070603@samsung.com
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: rt@linutronix.de
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: linux-leds@vger.kernel.org
Link: http://lkml.kernel.org/r/1469028295-14702-1-git-send-email-bigeasy@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Otherwise the driver module will not be automatically probed.
Fixes: 9d7cffaf99 ("leds: Add driver for the ISSI IS31FL32xx family of LED controllers")
Fixes: e0442d7def ("leds: Add SN3218 and SN3216 support to the IS31FL32XX driver")
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Tested-by: David Rivshin <drivshin@allworx.com>
Acked-by: David Rivshin <drivshin@allworx.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Tested-by: David Rivshin <drivshin@allworx.com>
Acked-by: David Rivshin <drivshin@allworx.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
The chip can drive 2 sets of RGB leds. Controller can
be controlled via PWM, I2C and audio synchronisation.
This driver uses I2C to communicate with the chip.
Datasheet: http://www.ti.com/lit/gpn/lp3952
Signed-off-by: Tony Makkiel <tony.makkiel@daqri.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
This is a straightforward conversion. We place this callback last
in the list so that the LED illuminates only after a successful
bring up sequence.
( NOTE: The patch adds a FIXME question about the callback used,
this question should probably be revisited later on.)
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-leds@vger.kernel.org
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160713153336.465496902@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
When working with Device Tree we iterate over children of "gpio-leds"
compatible node and create LED device for each of them. We take care of
all common DT properties (label, default trigger, state, etc.), however
some triggers may want to support more of them.
It could be useful for timer trigger to support setting delay on/off
values with Device Tree property. Or for transient trigger to support
e.g. duration property.
We obviously should handle such properties in triggers, not in generic
code. To let trigger drivers read properties from DT node we need to set
of_node to point the relevant node. This change allows using all kind of
of helpers in e.g. "activate" callbacks.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
If an invalid trigger name is provided via sysfs currently no error
is returned. Therefore it's not possible to determine whether the
trigger was set successfully.
Fix this by returning -EINVAL if no trigger is matched.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
An opal_msg of type OPAL_MSG_ASYNC_COMP contains the return code in the
params[1] struct member. However this isn't intuitive or obvious when
reading the code and requires that a user look at the skiboot
documentation or opal-api.h to verify this.
Add an inline function to get the return code from an opal_msg and update
call sites accordingly.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch converts the IDE specific LED trigger to a generic disk
activity LED trigger. The libata core is now a trigger source just
like before the IDE disk driver. It's merely a replacement of the
string ide by disk.
The patch is taken from http://dev.gentoo.org/~josejx/ata.patch and is
widely used by any ibook/powerbook owners with great satisfaction.
Likewise, it is very often used successfully on different ARM platforms.
Unlike the original patch, the existing 'ide-disk' trigger is still
available for backward compatibility. That reduce the amount of patches
in affected device trees out of the mainline kernel. For further
development, the new name 'disk-activity' should be used.
Cc: Joseph Jezak <josejx@gentoo.org>
Cc: Jörg Sommer <joerg@alea.gnuu.de>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Stephan Linz <linz@li-pro.net>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
This patch adds basic device tree support for the pca9532 LEDs.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
The following phenomena was observed: when suspending the
system, sometimes the heartbeat LED was left on, glowing and
wasting power while the rest of the system is asleep, also
disturbing power dissapation measures on the odd suspend
cycle when it's left on.
Clearly this is not how we want the heartbeat trigger to
work: it should turn off and leave the LED off during
system suspend.
This removes the heartbeat trigger when preparing suspend and
restores it during resume. The trigger code will make sure all
LEDs are left in OFF state after removing the trigger, and
will re-enable the trigger on all LEDs after resuming.
Cc: linux-pm@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Commit 76931edd54 ("leds: fix brightness changing when software blinking
is active") changed the semantics of led_set_brightness() which according
to the documentation should disable blinking upon any brightness setting.
Moreover it made it different for soft blink case, where it was possible
to change blink brightness, and for hardware blink case, where setting
any brightness greater than 0 was ignored.
While the change itself is against the documentation claims, it was driven
also by the fact that timer trigger remained active after turning blinking
off. Fixing that would have required major refactoring in the led-core,
led-class, and led-triggers because of cyclic dependencies.
Finally, it has been decided that allowing for brightness change during
blinking is beneficial as it can be accomplished without disturbing
blink rhythm.
The change in brightness setting semantics will not affect existing
LED class drivers that implement blink_set op thanks to the LED_BLINK_SW
flag introduced by this patch. The flag state will be from now on checked
in led_set_brightness() which will allow to distinguish between software
and hardware blink mode. In the latter case the control will be passed
directly to the drivers which apply their semantics on brightness set,
which is disable the blinking in case of most such drivers. New drivers
will apply new semantics and just change the brightness while hardware
blinking is on, if possible.
The issue was smuggled by subsequent LED core improvements, which modified
the code that originally introduced the problem.
Fixes: f1e80c0741 ("leds: core: Add two new LED_BLINK_ flags")
Signed-off-by: Tony Makkiel <tony.makkiel@daqri.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
This set of changes introduces an atomic API to the PWM subsystem. This
is influenced by the DRM atomic API that was introduced a while back,
though it is obviously a lot simpler. The fundamental idea remains the
same, though: drivers provide a single callback to implement the atomic
configuration of a PWM channel.
As a side-effect the PWM subsystem gains the ability for initial state
retrieval, so that the logical state mirrors that of the hardware. Many
use-cases don't care about this, but for others it is essential.
These new features require changes in all users, which these patches
take care of. The core is transitioned to use the atomic callback if
available and provides a fallback mechanism for other drivers.
Changes to transition users and drivers to the atomic API are postponed
to v4.8.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=sxT9
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"This set of changes introduces an atomic API to the PWM subsystem.
This is influenced by the DRM atomic API that was introduced a while
back, though it is obviously a lot simpler. The fundamental idea
remains the same, though: drivers provide a single callback to
implement the atomic configuration of a PWM channel.
As a side-effect the PWM subsystem gains the ability for initial state
retrieval, so that the logical state mirrors that of the hardware.
Many use-cases don't care about this, but for others it is essential.
These new features require changes in all users, which these patches
take care of. The core is transitioned to use the atomic callback if
available and provides a fallback mechanism for other drivers.
Changes to transition users and drivers to the atomic API are
postponed to v4.8"
* tag 'pwm/for-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (30 commits)
pwm: Add information about polarity, duty cycle and period to debugfs
pwm: Switch to the atomic API
pwm: Update documentation
pwm: Add core infrastructure to allow atomic updates
pwm: Add hardware readout infrastructure
pwm: Move the enabled/disabled info into pwm_state
pwm: Introduce the pwm_state concept
pwm: Keep PWM state in sync with hardware state
ARM: Explicitly apply PWM config extracted from pwm_args
drm: i915: Explicitly apply PWM config extracted from pwm_args
input: misc: pwm-beeper: Explicitly apply PWM config extracted from pwm_args
input: misc: max8997: Explicitly apply PWM config extracted from pwm_args
backlight: lm3630a: explicitly apply PWM config extracted from pwm_args
backlight: lp855x: Explicitly apply PWM config extracted from pwm_args
backlight: lp8788: Explicitly apply PWM config extracted from pwm_args
backlight: pwm_bl: Use pwm_get_args() where appropriate
fbdev: ssd1307fb: Use pwm_get_args() where appropriate
regulator: pwm: Use pwm_get_args() where appropriate
leds: pwm: Use pwm_get_args() where appropriate
input: misc: max77693: Use pwm_get_args() where appropriate
...
The PWM framework has clarified the concept of reference PWM config (the
platform dependent config retrieved from the DT or the PWM lookup table)
and real PWM state.
Use pwm_get_args() when the PWM user wants to retrieve this reference
config and not the current state.
This is part of the rework allowing the PWM framework to support
hardware readout and expose real PWM state even when the PWM has just
been requested (before the user calls pwm_config/enable/disable()).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Calling a GPIO LEDs is quite likely to work even if the kernel
has paniced, so they are ideal to blink in this situation.
This commit adds support for the new "panic-indicator"
firmware property, allowing to mark a given LED to blink on
a kernel panic.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
This commit adds a new led_cdev flag LED_PANIC_INDICATOR, which
allows to mark a specific LED to be switched to the "panic"
trigger, on a kernel panic.
This is useful to allow the user to assign a regular trigger
to a given LED, and still blink that LED on a kernel panic.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
The Intel NAS SS4200 was also sold by Fujitsu Siemens (FSC) under
the name "SCALEO Home Server". The hardware is equivalent.
This patch adds the DMI data of this rebranded device.
Signed-off-by: Martin Dummer <martin.dummer@gmx.net>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
There is only one x86 hardware where the driver leds-ss4200 applies to.
Add kconfig dependency to x86 architecture, fix help text whitespace.
Signed-off-by: Martin Dummer <martin.dummer@gmx.net>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Parameters delay_on and delay_off of led_trigger_blink_oneshot()
are pointers, to enable blink interval adjustment by LED class drivers
of the controllers that implement hardware blinking.
Move ide_blink_delay variable to ledtrig_ide_activity() in order to
prevent the situation when adjustment committed by one LED class
driver influences blink interval of the software fallback blink feature,
that is applied to the drivers that don't implement blink_set op.
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
If choose_times() returns -EINVAL that means "c1" and "c2" haven't been
initialized. I've added a check for that.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
This commit introduces a MTD trigger for flash (NAND/NOR) device
activity. The implementation is copied from IDE disk.
This trigger deprecates the "nand-disk" LED trigger, but for backwards
compatibility, we still keep the "nand-disk" trigger around.
The motivation for deprecating the "nand-disk" LED trigger is that
it only works for NAND drivers, whereas the "mtd" LED trigger
is more generic (in fact, "nand-disk" currently only works for
certain NAND drivers).
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
This commit introduces a new LED trigger which allows to configure
a LED to blink on a kernel panic (through panic_blink).
Notice that currently the Openmoko FreeRunner (GTA02) mach code
sets panic_blink to blink a hard-coded LED. The new trigger is
meant to introduce a generic mechanism to achieve this.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Significant refactoring of Dell laptop drivers, modularizing the smbios code.
Multiple new platforms added for ideapad, asus, dell, and alienware using
existing quirks. A few fixes and cleanups.
hp-wmi:
- Remove GPS rfkill support via pre-2009 interface
- fix unregister order in hp_wmi_rfkill_setup() once again
ideapad-laptop:
- Add ideapad Y700 (15) to the no_hw_rfkill DMI list
fujitsu-laptop:
- Support radio toggle button
intel-hid:
- allocate correct amount of memory for private struct
platform/x86:
- Make intel_scu_ipc explicitly non-modular
intel_pmc_ipc:
- Avoid pending IPC1 command during legacy suspend
- Fix GCR register base address and length
asus-nb-wmi:
- add wapf=4 quirk for ASUS X75VD
intel_telemetry_pltdrv:
- Change verbosity control bits
dell-rbtn:
- Add a comment about the XPS 13 9350
dell-wmi, dell-laptop:
- depends DMI
dell-wmi:
- support Dell Inspiron M5110
- properly process Dell Instant Launch hotkey
- enable receiving WMI events on Dell Vostro V131
- Support new hotkeys on the XPS 13 9350 (Skylake)
- Clean up hotkey table size check
- Stop storing pointers to DMI tables
dell-laptop:
- move dell_smi_error() to dell-smbios
- use dell_smbios_find_token() instead of find_token_location()
- use dell_smbios_find_token() instead of find_token_id()
- extract SMBIOS-related code to a separate module
dell-smbios:
- rename dell_smi_error() to dell_smbios_error()
- make da_tokens static
- remove find_token_{id,location}()
- implement new function for finding DMI table 0xDA tokens
- make the SMBIOS buffer static
- return the SMBIOS buffer from dell_smbios_get_buffer()
- don't return an SMBIOS buffer from dell_smbios_send_request()
- don't pass an SMBIOS buffer to dell_smbios_send_request()
- rename dell_send_request() to dell_smbios_send_request()
- rename release_buffer() to dell_smbios_release_buffer()
- rename clear_buffer() to dell_smbios_clear_buffer()
- rename get_buffer() to dell_smbios_get_buffer()
dell-led:
- use dell_smbios_send_request() for performing SMBIOS calls
- use dell_smbios_find_token() for finding mic DMI tokens
toshiba_acpi:
- Add a module parameter to disable hotkeys registration
- Add sysfs entries for the Cooling Method feature
- Add support for cooling method feature
Documentation/ABI:
- Update sysfs-driver-toshiba_acpi file
thinkpad_acpi:
- Remove ambiguous logging for "Unsupported brightness interface"
alienware-wmi:
- whitespace improvements
- Add support for two new systems: ASM200 and ASM201.
- Add support for deep sleep control.
- Add initial support for alienware graphics amplifier.
- Add support for new platform: X51-R3
- Clean up whitespace for ASM100 platform
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJW8s77AAoJEKbMaAwKp364iVgH/18Tpefbc7uOrNak4zfTmvVO
CQjLdbnbCYoeNjwgdYSZNlaR+E2TuMdqmBXXLEr3kqicpmX15l+V5y8xJkDmGpxw
0RmwJnkdIpmkZcjb3/2abOtIuOj1Y/tXCp5mY1FoaDYBQVzO+ZsPEGNQcMu5uJpa
qZTw9UwiSPUspTrHHbS7/Bzv7yFnxlWC1nmt6G5zL4OMEv2AGbuVSstXVGySIML5
TfFdisUBIXQplzwpDytHGqtGUJMc0NnT1s66beuo1oBdEFTFtBNpFySW3goV2nrZ
JPbvyaV3tD24NYNmU9WH653InX4KuaGiJRWVT31a/I5HVVlx7mZdUYRI+EYAnmE=
=e0E4
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v4.6-1' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86
Pull x86 platform driver updates from Darren Hart:
"Significant refactoring of Dell laptop drivers, modularizing the
smbios code. Multiple new platforms added for ideapad, asus, dell,
and alienware using existing quirks. A few fixes and cleanups.
hp-wmi:
- Remove GPS rfkill support via pre-2009 interface
- fix unregister order in hp_wmi_rfkill_setup() once again
ideapad-laptop:
- Add ideapad Y700 (15) to the no_hw_rfkill DMI list
fujitsu-laptop:
- Support radio toggle button
intel-hid:
- allocate correct amount of memory for private struct
platform/x86:
- Make intel_scu_ipc explicitly non-modular
intel_pmc_ipc:
- Avoid pending IPC1 command during legacy suspend
- Fix GCR register base address and length
asus-nb-wmi:
- add wapf=4 quirk for ASUS X75VD
intel_telemetry_pltdrv:
- Change verbosity control bits
dell-rbtn:
- Add a comment about the XPS 13 9350
dell-wmi, dell-laptop:
- depends DMI
dell-wmi:
- support Dell Inspiron M5110
- properly process Dell Instant Launch hotkey
- enable receiving WMI events on Dell Vostro V131
- Support new hotkeys on the XPS 13 9350 (Skylake)
- Clean up hotkey table size check
- Stop storing pointers to DMI tables
dell-laptop:
- move dell_smi_error() to dell-smbios
- use dell_smbios_find_token() instead of find_token_location()
- use dell_smbios_find_token() instead of find_token_id()
- extract SMBIOS-related code to a separate module
dell-smbios:
- rename dell_smi_error() to dell_smbios_error()
- make da_tokens static
- remove find_token_{id,location}()
- implement new function for finding DMI table 0xDA tokens
- make the SMBIOS buffer static
- return the SMBIOS buffer from dell_smbios_get_buffer()
- don't return an SMBIOS buffer from dell_smbios_send_request()
- don't pass an SMBIOS buffer to dell_smbios_send_request()
- rename dell_send_request() to dell_smbios_send_request()
- rename release_buffer() to dell_smbios_release_buffer()
- rename clear_buffer() to dell_smbios_clear_buffer()
- rename get_buffer() to dell_smbios_get_buffer()
dell-led:
- use dell_smbios_send_request() for performing SMBIOS calls
- use dell_smbios_find_token() for finding mic DMI tokens
toshiba_acpi:
- Add a module parameter to disable hotkeys registration
- Add sysfs entries for the Cooling Method feature
- Add support for cooling method feature
Documentation/ABI:
- Update sysfs-driver-toshiba_acpi file
thinkpad_acpi:
- Remove ambiguous logging for "Unsupported brightness interface"
alienware-wmi:
- whitespace improvements
- Add support for two new systems: ASM200 and ASM201.
- Add support for deep sleep control.
- Add initial support for alienware graphics amplifier.
- Add support for new platform: X51-R3
- Clean up whitespace for ASM100 platform"
* tag 'platform-drivers-x86-v4.6-1' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86: (47 commits)
hp-wmi: Remove GPS rfkill support via pre-2009 interface
hp-wmi: fix unregister order in hp_wmi_rfkill_setup() once again
dell-wmi: support Dell Inspiron M5110
dell-wmi: properly process Dell Instant Launch hotkey
dell-wmi: enable receiving WMI events on Dell Vostro V131
dell-smbios: rename dell_smi_error() to dell_smbios_error()
dell-laptop: move dell_smi_error() to dell-smbios
ideapad-laptop: Add ideapad Y700 (15) to the no_hw_rfkill DMI list
fujitsu-laptop: Support radio toggle button
intel-hid: allocate correct amount of memory for private struct
platform/x86: Make intel_scu_ipc explicitly non-modular
intel_pmc_ipc: Avoid pending IPC1 command during legacy suspend
intel_pmc_ipc: Fix GCR register base address and length
asus-nb-wmi: add wapf=4 quirk for ASUS X75VD
intel_telemetry_pltdrv: Change verbosity control bits
dell-rbtn: Add a comment about the XPS 13 9350
dell-wmi: Support new hotkeys on the XPS 13 9350 (Skylake)
dell-wmi: Clean up hotkey table size check
dell-wmi, dell-laptop: depends DMI
dell-wmi: Stop storing pointers to DMI tables
...
Instead of using the WMI wrapper, dell-led can take advantage of
dell_smbios_send_request() for performing the SMBIOS calls required to
change the state of the microphone LED.
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
With the advent of dell_smbios_find_token(), dell-led does not need to
perform any DMI walking on its own, but it can rather ask dell-smbios to
look up the DMI tokens it needs for changing the state of the microphone
LED.
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
led_trigger_store can be significantly simplified by using sysfs_streq().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Switch to resource-managed function devm_led_classdev_register instead
of led_classdev_register and remove unneeded led_classdev_unregister.
Also, remove platform_set_drvdata in probe function and the remove
function, max8997_led_remove as it is now has nothing to do.
The Coccinelle semantic patch used to make this change is as follows:
//<smpl>
@platform@
identifier p, probefn, removefn;
@@
struct platform_driver p = {
.probe = probefn,
.remove = removefn,
};
@prb@
identifier platform.probefn, pdev;
expression e;
@@
probefn(struct platform_device *pdev, ...) {
...
e =
- led_classdev_register
+ devm_led_classdev_register
(...);
...
?- led_classdev_unregister(...);
...
}
@remove depends on prb@
identifier platform.removefn;
@@
removefn(...) {
...
?- led_classdev_unregister(...);
...
}
//</smpl>
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Switch to resource-managed function devm_led_classdev_register instead
of led_classdev_register and remove unneeded led_classdev_unregister.
Also, remove platform_set_drvdata in probe function and the remove
function, da903x_led_remove as it is now has nothing to do.
The Coccinelle semantic patch used to make this change is as follows:
//<smpl>
@platform@
identifier p, probefn, removefn;
@@
struct platform_driver p = {
.probe = probefn,
.remove = removefn,
};
@prb@
identifier platform.probefn, pdev;
expression e;
@@
probefn(struct platform_device *pdev, ...) {
...
e =
- led_classdev_register
+ devm_led_classdev_register
(...);
...
?- led_classdev_unregister(...);
...
}
@remove depends on prb@
identifier platform.removefn;
@@
removefn(...) {
...
?- led_classdev_unregister(...);
...
}
//</smpl>
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Switch to resource-managed function devm_led_classdev_register instead
of led_classdev_register and remove unneeded led_classdev_unregister.
Also, remove unnecessary function pdev_to_gpio, platform_set_drvdata
in the probe function and the remove function, s3c24xx_led_remove as
it is now has nothing to do.
The Coccinelle semantic patch used to make this change is as follows:
//<smpl>
@platform@
identifier p, probefn, removefn;
@@
struct platform_driver p = {
.probe = probefn,
.remove = removefn,
};
@prb@
identifier platform.probefn, pdev;
expression e;
@@
probefn(struct platform_device *pdev, ...) {
...
e =
- led_classdev_register
+ devm_led_classdev_register
(...);
...
?- led_classdev_unregister(...);
...
}
@remove depends on prb@
identifier platform.removefn;
@@
removefn(...) {
...
?- led_classdev_unregister(...);
...
}
//</smpl>
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Switch to resource-managed function devm_led_classdev_register instead
of led_classdev_register and remove unneeded led_classdev_unregister.
Also, remove platform_set_drvdata from probe function and the remove
function, wm831x_status_remove as it is now has nothing to do.
The Coccinelle semantic patch used to make this change is as follows:
//<smpl>
@platform@
identifier p, probefn, removefn;
@@
struct platform_driver p = {
.probe = probefn,
.remove = removefn,
};
@prb@
identifier platform.probefn, pdev;
expression e;
@@
probefn(struct platform_device *pdev, ...) {
...
e =
- led_classdev_register
+ devm_led_classdev_register
(...);
...
?- led_classdev_unregister(...);
...
}
@remove depends on prb@
identifier platform.removefn;
@@
removefn(...) {
...
?- led_classdev_unregister(...);
...
}
//</smpl>
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Switch to resource-managed function devm_led_classdev_register instead
of led_classdev_register and remove unneeded led_classdev_unregister.
Also, remove platform_set_drvdata in probe function and the remove
function, lp8788_led_remove as it is now has nothing to do.
The Coccinelle semantic patch used to make this change is as follows:
//<smpl>
@platform@
identifier p, probefn, removefn;
@@
struct platform_driver p = {
.probe = probefn,
.remove = removefn,
};
@prb@
identifier platform.probefn, pdev;
expression e;
@@
probefn(struct platform_device *pdev, ...) {
...
e =
- led_classdev_register
+ devm_led_classdev_register
(...);
...
?- led_classdev_unregister(...);
...
}
@remove depends on prb@
identifier platform.removefn;
@@
removefn(...) {
...
?- led_classdev_unregister(...);
...
}
//</smpl>
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Switch to resource-managed function devm_led_classdev_register instead
of led_classdev_register and remove unneeded led_classdev_unregister.
Also, remove platform_set_drvdata in probe function and the remove
function, pm860x_led_remove as it is now has nothing to do.
The Coccinelle semantic patch used to make this change is as follows:
//<smpl>
@platform@
identifier p, probefn, removefn;
@@
struct platform_driver p = {
.probe = probefn,
.remove = removefn,
};
@prb@
identifier platform.probefn, pdev;
expression e;
@@
probefn(struct platform_device *pdev, ...) {
...
e =
- led_classdev_register
+ devm_led_classdev_register
(...);
...
?- led_classdev_unregister(...);
...
}
@remove depends on prb@
identifier platform.removefn;
@@
removefn(...) {
...
?- led_classdev_unregister(...);
...
}
//</smpl>
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Si-En Technology was acquired by ISSI in 2011, and it appears that
the IS31FL3218/IS31FL3216 are just rebranded SN3218/SN3216 devices.
Add the "si-en,sn3218" and "si-en,sn3216" compatible strings into the
IS31FL32XX driver as aliases for the issi equivalents, and update
binding documentation.
Datasheets:
IS31FL3218: http://www.issi.com/WW/pdf/31FL3218.pdf
SN3218: http://www.si-en.com/uploadpdf/s2011517171720.pdf
IS31FL3216: http://www.issi.com/WW/pdf/31FL3216.pdf
SN3216: http://www.si-en.com/uploadpdf/SN3216201152410148.pdf
Signed-off-by: David Rivshin <drivshin@allworx.com>
Acked-by: Rob Herring <robh@kernel.org>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
The IS31FL32xx family of LED controllers are I2C devices with multiple
constant-current channels, each with independent 256-level PWM control.
Datasheets: http://www.issi.com/US/product-analog-fxled-driver.shtml
This has been tested on the IS31FL3236 and IS31FL3216, on an ARM
(TI am335x) platform.
The programming paradigm of these devices is similar in the following
ways:
- All registers are 8 bit
- All LED control registers are write-only
- Each LED channel has a PWM register (0-255)
- PWM register writes are shadowed until an Update register is poked
- All have a concept of Software Shutdown, which disables output
However, there are some differences in devices:
- 3236/3235 have a separate Control register for each LED,
(3218/3216 pack the enable bits into fewer registers)
- 3236/3235 have a per-channel current divisor setting
- 3236/3235 have a Global Control register that can turn off all LEDs
- 3216 is unique in a number of ways
- OUT9-OUT16 can be configured as GPIOs instead of LED controls
- LEDs can be programmed with an 8-frame animation, with
programmable delay between frames
- LEDs can be modulated by an input audio signal
- Max output current can be adjusted from 1/4 to 2x globally
- Has a Configuration register instead of a Shutdown register
This driver currently only supports the base PWM control function
of these devices. The following features of these devices are not
implemented, although it should be possible to add them in the future:
- All devices are capable of going into a lower-power "software
shutdown" mode.
- The is31fl3236 and is31fl3235 can reduce the max output current
per-channel with a divisor of 1, 2, 3, or 4.
- The is31fl3216 can use some LED channels as GPIOs instead.
- The is31fl3216 can animate LEDs in hardware.
- The is31fl3216 can modulate LEDs according to an audio input.
- The is31fl3216 can reduce/increase max output current globally.
Signed-off-by: David Rivshin <drivshin@allworx.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Switch to resource-managed function devm_led_classdev_register instead
of led_classdev_register and remove unneeded led_classdev_unregister.
To be compatible with this change, remove an unnecessary label by
replacing it with direct return statement.
The Coccinelle semantic patch used to make this change is as follows:
//<smpl>
@platform@
identifier p, probefn, removefn;
@@
struct platform_driver p = {
.probe = probefn,
.remove = removefn,
};
@prb@
identifier platform.probefn, pdev;
expression e;
@@
probefn(struct platform_device *pdev, ...) {
...
e =
- led_classdev_register
+ devm_led_classdev_register
(...);
...
?- led_classdev_unregister(...);
...
}
@remove depends on prb@
identifier platform.removefn;
@@
removefn(...) {
...
?- led_classdev_unregister(...);
...
}
//</smpl>
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Use the GPIO flag definition instead of a numeric literal, so the casual
reader grepping for GPIOF_ will find the GPIO flags used.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Add helpers for calling brightness_set(_blocking) allowing to
simplify the code and make it better readable.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
In case of error, the function gpio_to_desc() returns NULL
pointer not ERR_PTR(). The IS_ERR() test in the return value
check should be replaced with NULL test.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Improve the wording for the comment about the led status, and while at
it also use the standard formatting for multi-line comments.
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
When a USB LED device is unplugged the remove call chain calls
led_classdev_unregister which tries to switch the LED off.
As the device has been removed already this results in a ENODEV
error message in dmesg.
Avoid this error message by ignoring ENODEV in calls from
led_classdev_unregister if the LED device is flagged as pluggable.
Therefore a new flag LED_HW_PLUGGABLE was introduced which should be set by
all LED drivers handling pluggable LED devices (mainly USB LED devices).
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Infrastructural changes:
- In struct gpio_chip, rename the .dev node to .parent to better reflect
the fact that this is not the GPIO struct device abstraction. We will
add that soon so this would be totallt confusing.
- It was noted that the driver .get_value() callbacks was
sometimes reporting negative -ERR values to the gpiolib core, expecting
them to be propagated to consumer gpiod_get_value() and gpio_get_value()
calls. This was not happening, so as there was a mess of drivers
returning negative errors and some returning "anything else than zero"
to indicate that a line was active. As some would have bit 31 set to
indicate "line active" it clashed with negative error codes. This is
fixed by the largeish series clamping values in all drivers with
!!value to [0,1] and then augmenting the code to propagate error codes
to consumers. (Includes some ACKed patches in other subsystems.)
- Add a void *data pointer to struct gpio_chip. The container_of() design
pattern is indeed very nice, but we want to reform the struct gpio_chip
to be a non-volative, stateless business, and keep states internal to
the gpiolib to be able to hold on to the state when adding a proper
userspace ABI (character device) further down the road. To achieve this,
drivers need a handle at the internal state that is not dependent on
their struct gpio_chip() so we add gpiochip_add_data() and
gpiochip_get_data() following the pattern of many other subsystems.
All the "use gpiochip data pointer" patches transforms drivers to this
scheme.
- The Generic GPIO chip header has been merged into the general
<linux/gpio/driver.h> header, and the custom header for that removed.
Instead of having a separate mm_gpio_chip struct for these generic
drivers, merge that into struct gpio_chip, simplifying the code and
removing the need for separate and confusing includes.
Misc improvements:
- Stabilize the way GPIOs are looked up from the ACPI legacy
specification.
- Incremental driver features for PXA, PCA953X, Lantiq (patches from the
OpenWRT community), RCAR, Zynq, PL061, 104-idi-48
New drivers:
- Add a GPIO chip to the ALSA SoC AC97 driver.
- Add a new Broadcom NSP SoC driver (this lands in the pinctrl dir, but
the branch is merged here too to account for infrastructural changes).
- The sx150x driver now supports the sx1502.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=63rR
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"Here is the bulk of GPIO changes for v4.5.
Notably there are big refactorings mostly by myself, aimed at getting
the gpio_chip into a shape that makes me believe I can proceed to
preserve state for a proper userspace ABI (character device) that has
already been proposed once, but resulted in the feedback that I need
to go back and restructure stuff. So I've been restructuring stuff.
On the way I ran into brokenness (return code from the get_value()
callback) and had to fix it. Also, refactored generic GPIO to be
simpler.
Some of that is still waiting to trickle down from the subsystems all
over the kernel that provide random gpio_chips, I've touched every
single GPIO driver in the kernel now, oh man I didn't know I was
responsible for so much...
Apart from that we're churning along as usual.
I took some effort to test and retest so it should merge nicely and we
shook out a couple of bugs in -next.
Infrastructural changes:
- In struct gpio_chip, rename the .dev node to .parent to better
reflect the fact that this is not the GPIO struct device
abstraction. We will add that soon so this would be totallt
confusing.
- It was noted that the driver .get_value() callbacks was sometimes
reporting negative -ERR values to the gpiolib core, expecting them
to be propagated to consumer gpiod_get_value() and gpio_get_value()
calls. This was not happening, so as there was a mess of drivers
returning negative errors and some returning "anything else than
zero" to indicate that a line was active. As some would have bit
31 set to indicate "line active" it clashed with negative error
codes. This is fixed by the largeish series clamping values in all
drivers with !!value to [0,1] and then augmenting the code to
propagate error codes to consumers. (Includes some ACKed patches
in other subsystems.)
- Add a void *data pointer to struct gpio_chip. The container_of()
design pattern is indeed very nice, but we want to reform the
struct gpio_chip to be a non-volative, stateless business, and keep
states internal to the gpiolib to be able to hold on to the state
when adding a proper userspace ABI (character device) further down
the road. To achieve this, drivers need a handle at the internal
state that is not dependent on their struct gpio_chip() so we add
gpiochip_add_data() and gpiochip_get_data() following the pattern
of many other subsystems. All the "use gpiochip data pointer"
patches transforms drivers to this scheme.
- The Generic GPIO chip header has been merged into the general
<linux/gpio/driver.h> header, and the custom header for that
removed. Instead of having a separate mm_gpio_chip struct for
these generic drivers, merge that into struct gpio_chip,
simplifying the code and removing the need for separate and
confusing includes.
Misc improvements:
- Stabilize the way GPIOs are looked up from the ACPI legacy
specification.
- Incremental driver features for PXA, PCA953X, Lantiq (patches from
the OpenWRT community), RCAR, Zynq, PL061, 104-idi-48
New drivers:
- Add a GPIO chip to the ALSA SoC AC97 driver.
- Add a new Broadcom NSP SoC driver (this lands in the pinctrl dir,
but the branch is merged here too to account for infrastructural
changes).
- The sx150x driver now supports the sx1502"
* tag 'gpio-v4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (220 commits)
gpio: generic: make bgpio_pdata always visible
gpiolib: fix chip order in gpio list
gpio: mpc8xxx: Do not use gpiochip_get_data() in mpc8xxx_gpio_save_regs()
gpio: mm-lantiq: Do not use gpiochip_get_data() in ltq_mm_save_regs()
gpio: brcmstb: Allow building driver for BMIPS_GENERIC
gpio: brcmstb: Set endian flags for big-endian MIPS
gpio: moxart: fix build regression
gpio: xilinx: Do not use gpiochip_get_data() in xgpio_save_regs()
leds: pca9532: use gpiochip data pointer
leds: tca6507: use gpiochip data pointer
hid: cp2112: use gpiochip data pointer
bcma: gpio: use gpiochip data pointer
avr32: gpio: use gpiochip data pointer
video: fbdev: via: use gpiochip data pointer
gpio: pch: Optimize pch_gpio_get()
Revert "pinctrl: lantiq: Implement gpio_chip.to_irq"
pinctrl: nsp-gpio: use gpiochip data pointer
pinctrl: vt8500-wmt: use gpiochip data pointer
pinctrl: exynos5440: use gpiochip data pointer
pinctrl: at91-pio4: use gpiochip data pointer
...
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Riku Voipio <riku.voipio@iki.fi>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: linux-leds@vger.kernel.org
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Riku Voipio <riku.voipio@iki.fi>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: linux-leds@vger.kernel.org
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Ran into this on UML:
drivers/built-in.o: In function `bcm6328_leds_probe':
drivers/leds/leds-bcm6328.c:340: undefined reference to `devm_ioremap_resource'
drivers/built-in.o: In function `bcm6358_leds_probe':
drivers/leds/leds-bcm6358.c:173: undefined reference to `devm_ioremap_resource'
collect2: error: ld returned 1 exit status
devm_ioremap_resource() is defined only when HAS_IOMEM is selected.
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: linux-leds@vger.kernel.org
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Complementing devm_led_classdev_register add a managed version of
led_trigger_register.
I omit a managed version of led_classdev_unregister as the equivalent
devm_led_classdev_unregister isn't used in the kernel as of today.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
The busy status checking isn't needed while reading initial LED status.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
BCM6328 controller has a margin of 20ms per blink step, which means that
we can only set it to 20, 40, 60 ... 1260 ms (0x3f * 20ms).
However, when checking if delay_on == delay_off, we were not considering
the case when the user had set delay_on=20 and delay_off=21, since this
will cause the driver to fallback to software blinking.
This update fixes this issue and improves blink steps by rounding them
in a more sensible way. Now 30-49ms is rounded to 40 ms, and previous
behaviour implied 40-59ms being rounded to 40 ms.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
bcm6358_led_mode is now only called by bcm6358_led_set, so merge both
in one single function.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Instead of duplicating the unlock we can store the return value and use a
single unlock before returning that value, which simplifies the code.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
This adds little endian support while keeping big endian support.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
This adds little endian support while keeping big endian support.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
This lock isn't really needed, since we're only reading the register and
changes made to other LEDs aren't relevant.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Replaces bcm6358_led_mode with bcm6358_led_set so we don't need to handle
the lock.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
This lock isn't really needed, since we're only reading the register and
changes made to other LEDs aren't relevant.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
The Kconfig currently controlling compilation of this code is:
drivers/leds/Kconfig:config LEDS_SYSCON
drivers/leds/Kconfig: bool "LED support for LEDs on system controllers"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: linux-leds@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
The Kconfig for this driver is currently:
config LEDS_TRIGGER_IDE_DISK
bool "LED IDE Disk Trigger"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Bryan Wu <cooloney@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: linux-leds@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
The Kconfig for this driver is currently:
config LEDS_TRIGGER_CPU
bool "LED CPU Trigger"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Bryan Wu <cooloney@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: linux-leds@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
These new helpers simplify implementing multi-driver modules and
properly handle failure to register one driver by unregistering all
previously registered drivers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Each break out of the for_each_available_child_of_node loop requires
of_node_put().
This patch adds missing of_node_put() when loop breaks on conflicting
values of led-sources DT property.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Sakari Ailus <sakari.ailus@linux.intel.com>
The refcount of device_node increases after of_get_next_available_child()
is called. Make sure it is decremented also in case of DT parsing error.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Sakari Ailus <sakari.ailus@linux.intel.com>
Since brightness setting can sleep for this driver, implement
brightness_set_blocking op, instead of brightness_set.
It makes this driver compatible with LED triggers.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Cc: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
Since brightness setting can sleep for this driver, implement
brightness_set_blocking op, instead of brightness_set.
It makes this driver compatible with LED triggers.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
No need to explicitly check for pointer to be null,
of_prop_next_string anyways returns NULL, if passed pointer is NULL
and hence loop will continue.
Signed-off-by: Saurabh Sengar <saurabh.truth@gmail.com>
Acked-by: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
The values of BCM6328_LED_MODE_ON and BCM6328_LED_MODE_OFF were named
for active low LEDs. These should be swapped so that they are named for
the default case of active high LEDs.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
When ensuring a consistent initial LED state in bcm6328_led (as they may
be blinking instead of on/off), the LED register is set using an inverted
copy of bcm6328_led_set(). To avoid further errors relating to active low
handling, call this function directly instead.
As bcm6328_led_set() acquires the same spinlock again when updating the
register, it is called after unlocking.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Now the core implements the work queue, remove it from the drivers,
and switch to using brightness_set_blocking op.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Tested-by: Simon Guinot <simon.guinot@sequanux.org>
Workqueue, 'set_brightness_work' is used for scheduling brightness control.
This workqueue is canceled when the LED class device is unregistered.
Currently, LED subsystem handles like below.
cancel_work_sync(&led_cdev->set_brightness_work)
led_set_brightness(led_cdev, LED_OFF)
However, this could be a problem.
Workqueue is going to be canceled but LED device needs to be off.
The worst case is null pointer access due to scheduling a workqueue.
LED module is loaded.
LED driver private data is allocated by using devm_zalloc().
LED module is unloaded.
led_classdev_unregister() is called.
cancel_work_sync()
led_set_brightness(led_cdev, LED_OFF)
schedule_work() if LED driver uses brightness_set_blocking()
In the meantime, driver private data will be freed.
..scheduling..
brightness_set_blocking() callback is invoked.
For the brightness control, LED driver tries to access private
data but resource is removed!
To avoid this problem, LED subsystem should turn off the brightness first
and wait for completion.
led_set_brightness(led_cdev, LED_OFF)
flush_work(&led_cdev->set_brightness_work)
It guarantees that LED driver turns off the brightness prior to
resource management.
Cc: linux-leds@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Milo Kim <milo.kim@ti.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Strobe state variable is declared as unsigned long, remove
the check for values less than zero then.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Reported-by: David Binderman <dcb314@hotmail.com>
The refcount of device_node increases after of_node_get() is called.
So, a break out of the loop requires of_node_put().
This patch adds missing of_node_put() when loop breaks.
Signed-off-by: Ingi Kim <ingi2.kim@samsung.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Some PWMs are disabled by default or the default pin setting
does not match the LED_OFF state (e.g., active-low leds).
Hence, the driver may end up reporting 0 brightness, but
the leds are actually on using full brightness, because
it never enforces its default configuration.
So enforce it by calling led_pwm_set() after successfully
registering the device.
Tested on a Phytec phyFLEX i.MX6Q board based on kernel
v3.19.5.
Signed-off-by: Markus Hofstaetter <markus.hofstaetter@ait.ac.at>
Tested-by: Markus Hofstaetter <markus.hofstaetter@ait.ac.at>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
The header of this file fixes the license to GPL 2 only without the
option to use later version. So use the string "GPL v2" that is to be
used in this case.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
The transient trigger duration is documented to be in msec units, but is
actually in jiffies units. Other time based triggers are in msec units
as well. Fix the timer setup to convert from msec.
This could break an existing userspace that worked around this problem,
but exposing jiffies to userspace is just wrong and would break anyway
if HZ is changed.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Shuah Khan <shuahkhan@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: linux-leds@vger.kernel.org
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Now the core implements the work queue, remove it from the drivers,
and switch to using brightness_set_blocking op.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Cc: Daniel Jeong <daniel.jeong@ti.com>
Cc: G.Shark Jeong <gshark.jeong@gmail.com>
Now the core implements the work queue, remove it from the drivers,
and switch to using brightness_set_blocking op.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Cc: Raphael Assenat <raph@8d.com>
Now the core implements the work queue, remove it from the drivers,
and switch to using brightness_set_blocking op.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Cc: Raphael Assenat <raph@8d.com>
Now the core implements the work queue, remove it from the drivers,
and switch to using brightness_set_blocking op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Antonio Ospite <ao2@ao2.it>
Reviewed-by: Mark Brown <broonie@kernel.org>
Now the core implements the work queue, remove it from the drivers,
and switch to using brightness_set_blocking op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Antonio Ospite <ao2@ao2.it>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Now the core implements the work queue, remove it from the drivers,
and switch to using brightness_set_blocking op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Now the core implements the work queue, remove it from the drivers,
and switch to using brightness_set_blocking op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Cc: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Now the core implements the work queue, remove it from the drivers,
and switch to using brightness_set_blocking op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Now the core implements the work queue, remove it from the drivers,
and switch to using brightness_set_blocking op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Now the core implements the work queue, remove it from the drivers,
and switch to using brightness_set_blocking op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Now the core implements the work queue, remove it from the drivers,
and switch to using brightness_set_blocking op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Now the core implements the work queue, remove it from the drivers,
and switch to using brightness_set_blocking op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Dan Murphy <dmurphy@ti.com>
Cc: Ricardo Ribalda <ricardo.ribalda@gmail.com>
Now the core implements the work queue, remove it from the drivers,
and switch to using brightness_set_blocking op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Cc: Nate Case <ncase@xes-inc.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Now the core implements the work queue, remove it from the drivers,
and switch to using brightness_set_blocking op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Now the core implements the work queue, remove it from the drivers,
and switch to using brightness_set_blocking op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Cc: Milo Kim <milo.kim@ti.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Now the core implements the work queue, remove it from the drivers,
and switch to using brightness_set_blocking op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Cc: Milo Kim <milo.kim@ti.com>
Now the core implements the work queue, remove it from the driver,
and switch to using brightness_set_blocking op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Antonio Ospite <ao2@ao2.it>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Now the core implements the work queue, remove it from the driver,
and switch to using brightness_set_blocking op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Now the core implements the work queue, remove it from the driver,
and switch to using brightness_set_blocking op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Cc: Daniel Jeong <daniel.jeong@ti.com>
Cc: G.Shark Jeong <gshark.jeong@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Now the core implements the work queue, remove it from the driver,
and switch to using brightness_set_blocking op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Cc: Johan Hovold <johan@kernel.org>
Now the core implements the work queue, remove it from the driver,
and switch to using brightness_set_blocking op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Cc: Jan-Simon Moeller <dl9pf@gmx.de>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Now the core implements the work queue, remove it from the driver,
and switch to using brightness_set_blocking op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Cc: Kim Kyuwon <q1.kim@samsung.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Now the core implements the work queue, remove it from the driver,
and switch to using brightness_set_blocking op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Cc: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Now the core implements the work queue, remove it from the driver,
and switch to using brightness_set_blocking op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Now the core implements the work queue, remove it from the driver,
and switch to using brightness_set_blocking op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Now the core implements the work queue, remove it from the drivers,
and switch to using brightness_set_blocking op.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Cc: Ingi Kim <ingi2.kim@samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Now the core implements the work queue, remove it from the drivers,
and switch to using brightness_set_blocking op.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Now the core implements the work queue, remove it from the drivers,
and switch to using brightness_set_blocking op.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
This patch removes SET_BRIGHTNESS_ASYNC and SET_BRIGHTNESS_SYNC flags.
led_set_brightness() now calls led_set_brightness_nosleep() instead of
choosing between sync and async op basing on the flags defined by the
driver.
From now on, if a user wants to make sure that brightness will be set
synchronously, they have to use led_set_brightness_sync() API. It is now
being made publicly available since it has become apparent that it is
a caller who should decide whether brightness is to be set in
a synchronous or an asynchronous way.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
This patch makes LED core capable of setting brightness for drivers
that implement brightness_set_blocking op. It removes from LED class
drivers responsibility for using work queues on their own.
In order to achieve this set_brightness_delayed callback is being
modified to directly call one of available ops for brightness setting.
led_set_brightness_async() function didn't set brightness in an
asynchronous way in all cases. It was mistakenly assuming that all
LED subsystem drivers used work queue in their brightness_set op,
whereas only half of them did that. Since it has no users now,
it is being removed.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
This patch adds led_set_brightness_nosleep() and led_set_brightness_nopm()
functions, that guarantee setting LED brightness in a non-blocking way.
The latter is used from pm_ops context and doesn't modify the brightness
cached in the struct led_classdev. Its execution always ends up with
a call to brightness setting op - either directly or through
a set_brightness_work, regardless of LED_SUSPENDED flag state.
The patch also replaces led_set_brightness_async() with
led_set_brightness_nosleep() in all places where the most vital was setting
brightness in a non sleeping way but not necessarily asynchronously, which
is not needed for non-blocking drivers.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
The initial purpose of brightness_set_sync op, introduced along with
the LED flash class extension, was to add a means for setting torch LED
brightness as soon as possible, which couldn't have been guaranteed by
brightness_set op. This patch renames the op to brightness_set_blocking,
which describes its purpose in a more generic way. It is beneficial
in view of the prospective changes in the LED core, aiming at removing
the need for using work queues in LED class drivers that can sleep
or use delays while setting brightness.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
This patch adds LED_BLINK_BRIGHTNESS_CHANGE flag to indicate that blink
brightness has changed, and LED_BLINK_DISABLE flag to indicate that
blinking deactivation has been requested. In order to use the flags
led_timer_function and set_brightness_delayed callbacks as well as
led_set_brightness() function are being modified. The main goal of these
modifications is to prepare set_brightness_work for extension of the
scope of its responsibilities.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
LED core has a mixture of EXPORT_SYMBOL and EXPORT_SYMBOL_GPL macros.
This patch fixes this discrepancy and switches to using EXPORT_SYMBOL_GPL
for each exported function.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
The name .dev in a struct is normally reserved for a struct device
that is let us say a superclass to the thing described by the struct.
struct gpio_chip stands out by confusingly using a struct device *dev
to point to the parent device (such as a platform_device) that
represents the hardware. As we want to give gpio_chip:s real devices,
this is not working. We need to rename this member to parent.
This was done by two coccinelle scripts, I guess it is possible to
combine them into one, but I don't know such stuff. They look like
this:
@@
struct gpio_chip *var;
@@
-var->dev
+var->parent
and:
@@
struct gpio_chip var;
@@
-var.dev
+var.parent
and:
@@
struct bgpio_chip *var;
@@
-var->gc.dev
+var->gc.parent
Plus a few instances of bgpio that I couldn't figure out how
to teach Coccinelle to rewrite.
This patch hits all over the place, but I *strongly* prefer this
solution to any piecemal approaches that just exercise patch
mechanics all over the place. It mainly hits drivers/gpio and
drivers/pinctrl which is my own backyard anyway.
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Rafał Miłecki <zajec5@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Alek Du <alek.du@intel.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Quite a lot of activity in SPI this cycle, almost all of it in drivers
with a few minor improvements and tweaks in the core.
- Updates to pxa2xx to support Intel Broxton and multiple chip selects.
- Support for big endian in the bcm63xx driver.
- Multiple slave support for the mt8173
- New driver for the auxiliary SPI controller in bcm2835 SoCs.
- Support for Layerscale SoCs in the Freescale DSPI driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWOehzAAoJECTWi3JdVIfQTPYH+wYMDG8gAIw2s0AJ4DvVe4qZ
sOAm1UgUJZxssrEA6BNqbfM0dfRo+oQJKmRd0Dc5n7LEMsYHdI/5yKHk8PCS6ZzD
iQyQCzbd0thDAqwuPaMP62cyPDHwyJX22VGTsgVnj6AZqAQ+9+g4SPKhFnm1Mlm4
hmDi6fdSrsqo8k8gkpVN8RFOfVsjAV1dLtAauQRWDHrqMxXURSrKG76eqAqUa5bn
BLPXBoj5PA0DMLPO2j+ADZwWN723LrI2mSSlc+ThjEX/OIt2OhAoiOTV5RPqaafy
TIsCkh68q/gYAsL5HtvvmgZByl41FLYiO0Z+rXmWUyMMbnvhZTLws9S2BNpBLuk=
=DgXG
-----END PGP SIGNATURE-----
Merge tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"Quite a lot of activity in SPI this cycle, almost all of it in drivers
with a few minor improvements and tweaks in the core.
- Updates to pxa2xx to support Intel Broxton and multiple chip selects.
- Support for big endian in the bcm63xx driver.
- Multiple slave support for the mt8173
- New driver for the auxiliary SPI controller in bcm2835 SoCs.
- Support for Layerscale SoCs in the Freescale DSPI driver"
* tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (87 commits)
spi: pxa2xx: Rework self-initiated platform data creation for non-ACPI
spi: pxa2xx: Add support for Intel Broxton
spi: pxa2xx: Detect number of enabled Intel LPSS SPI chip select signals
spi: pxa2xx: Add output control for multiple Intel LPSS chip selects
spi: pxa2xx: Use LPSS prefix for defines that are Intel LPSS specific
spi: Add DSPI support for layerscape family
spi: ti-qspi: improve ->remove() callback
spi/spi-xilinx: Fix race condition on last word read
spi: Drop owner assignment from spi_drivers
spi: Add THIS_MODULE to spi_driver in SPI core
spi: Setup the master controller driver before setting the chipselect
spi: dw: replace magic constant by DW_SPI_DR
spi: mediatek: mt8173 spi multiple devices support
spi: mediatek: handle controller_data in mtk_spi_setup
spi: mediatek: remove mtk_spi_config
spi: mediatek: Update document devicetree bindings to support multiple devices
spi: fix kernel-doc warnings about missing return desc in spi.c
spi: fix kernel-doc warnings about missing return desc in spi.h
spi: pxa2xx: Align a few defines
spi: pxa2xx: Save other reg_cs_ctrl bits when configuring chip select
...
for_each_child_of_node performs an of_node_get on each iteration, so
a break out of the loop requires an of_node_put.
A simplified version of the semantic patch that fixes this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
local idexpression n;
expression e,r;
@@
for_each_child_of_node(r,n) {
...
(
of_node_put(n);
|
e = n
|
+ of_node_put(n);
? break;
)
...
}
... when != n
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
for_each_available_child_of_node performs an of_node_get on each
iteration, so a break out of the loop requires an of_node_put.
A simplified version of the semantic patch that fixes this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
expression root,e;
local idexpression child;
@@
for_each_available_child_of_node(root, child) {
... when != of_node_put(child)
when != e = child
(
return child;
|
+ of_node_put(child);
? return ...;
)
...
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
for_each_available_child_of_node performs an of_node_get on each
iteration, so a break out of the loop requires an of_node_put.
A simplified version of the semantic patch that fixes this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
expression root,e;
local idexpression child;
@@
for_each_available_child_of_node(root, child) {
... when != of_node_put(child)
when != e = child
(
return child;
|
+ of_node_put(child);
? return ...;
)
...
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
for_each_child_of_node performs an of_node_get on each iteration, so
a break out of the loop requires an of_node_put.
A simplified version of the semantic patch that fixes this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
expression root,e;
local idexpression child;
@@
for_each_child_of_node(root, child) {
... when != of_node_put(child)
when != e = child
(
return child;
|
+ of_node_put(child);
? return ...;
)
...
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Use of resource managed function devm_led_classdev_register to
make initialization path simpler. Also removed redundant remove
function.
Signed-off-by: Fida Mohammad <fmthoker@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Use devm_led_classdev_register instead of led_classdev_register,
removing the redundant net48xx_led_remove function.
Signed-off-by: Muhammad Falak R Wani <falakreyaz@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Use resource-managed function devm_led_classdev_register instead
of led_classdev_register, consequently remove redundant
menf21bmc_led_remove function.
Also drop the unneeded label err_free_leds.
Signed-off-by: Muhammad Falak R Wani <falakreyaz@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Use resource managed function devm_led_classdev_register to make
initialisation path simpler.
Also removed redundant led_classdev_unregister function.
Signed-off-by: Fida Mohammad <fmthoker@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
add a shutdown function for setting the gpio-leds
into off state when shuting down.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
This patch adds more init register configuration options:
- Serial LEDs multiplexing.
- Serial LEDs clock signal low/high polarity.
- Serial LEDs data signal low/high polarity.
- Serial LEDs shift direction inverted/normal.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
This patch simplifies and improves the code related to
default-state handling.
It also changes the code to power off the LEDs by default.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Print invalid LED instead of warning only about maximum LED value.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
This patch sets the led_classdev max_brightness to the maximum level
value supported by hardware. This allows to get rid of the brightness
conversion operation (from software [0:LED_FULL] to hardware ranges) in
brightness_set().
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
This patch converts the leds-netxbig driver to use the devres functions
devm_gpio_request_one() and devm_led_classdev_register(). This allows to
simplify the code a bit.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
This patch adds device tree support for the netxbig LEDs.
This also introduces a additionnal DT binding for the GPIO extension bus
(netxbig-gpio-ext) used to configure the LEDs. Since this bus could also
be used to control other devices, then it seems more suitable to have it
in a separate DT binding.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
This patch adds possibility to invert heartbeat blinking.
The inverted LED is more time ON then OFF. It's because it looks
better when the heartbeat LED is next to other LED which is most
time ON. The invert value is exported same way via sysfs in file
invert like oneshot. I get inspiration from this trigger.
Signed-off-by: Jiri Prchal <jiri.prchal@aksignal.cz>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Since the API for controlling LED brightness and blinking is defined in
the LED core, move the related timer and work callbacks to the led-core.c,
and initialize them through a new led_core_init API.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Pavel Machek <pavel@ucw.cz>
Spaces at the starting of a line are removed, indentation using
tab, instead of space. Also, line width of more than 80 characters
is also taken care of.
Two warnings are left alone to aid better readability.
Signed-off-by: Muhammad Falak R Wani <falakreyaz@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Use of resource-managed function devm_led_classdev_register
instead of led_classdev_register is preferred, consequently
remove redundant function micro_leds_remove.
Signed-off-by: Muhammad Falak R Wani <falakreyaz@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Use resource-managed function devm_led_classdev_register
instead of led_classdev_register to make the error path simpler.
The goto is replaced with direct return, unneeded label err is
dropped. Also, remove redundant ot200_led_remove.
Signed-off-by: Muhammad Falak R Wani <falakreyaz@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Use resource-managed function devm_led_classdev_register
instead of led_classdev_register to simplify error path.
An unnecessary check of ret is replaced with a direct return
Also, remove redundant hp6xxled_remove.
Signed-off-by: Muhammad Falak R Wani <falakreyaz@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Use resource-managed function devm_led_classdev_register instead
of led_classdev_register to make the error-path simpler.
To be compatible with the change, goto is replaced with direct
return, unneeded label err_null is dropped and unnecessary variable
retval is removed. Also, remove redundant cobalt_qube_led_remove.
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
An spi_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The commit [b67893206fc0: leds:lp55xx: fix firmware loading error]
tries to address the firmware file handling with user helper, but it
sets a wrong Kconfig CONFIG_FW_LOADER_USER_HELPER_FALLBACK. Since the
wrong option was enabled, the system got a regression -- it suffers
from the unexpected long delays for non-present firmware files.
This patch corrects the Kconfig dependency to the right one,
CONFIG_FW_LOADER_USER_HELPER. This doesn't change the fallback
behavior but only enables UMH when needed.
Bugzilla: https://bugzilla.opensuse.org/show_bug.cgi?id=944661
Fixes: b67893206f ('leds:lp55xx: fix firmware loading error')
Cc: <stable@vger.kernel.org> # v4.2+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luis@debethencourt.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luis@debethencourt.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luis@debethencourt.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luis@debethencourt.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luis@debethencourt.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luis@debethencourt.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
- Move PWM8941 WLED driver into Backlight
- Remove invalid use of IS_ERR_VALUE() macro
- Remove duplicate check for NULL data before unregistering
- Export I2C Device ID structure
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=URbg
-----END PGP SIGNATURE-----
Merge tag 'backlight-for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight
Pull backlight updates from Lee Jones:
- Stop using LP855X Platform Data to control regulators
- Move PWM8941 WLED driver into Backlight
- Remove invalid use of IS_ERR_VALUE() macro
- Remove duplicate check for NULL data before unregistering
- Export I2C Device ID structure
* tag 'backlight-for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight:
backlight: tosa: Export I2C module alias information
backlight: lp8788_bl: Delete a check before backlight_device_unregister()
backlight: sky81452: Remove unneeded use of IS_ERR_VALUE() macro
backlight: pm8941-wled: Move PM8941 WLED driver to backlight
backlight: lp855x: Use private data for regulator control
- Support "hybrid" iommu/direct DMA ops for coherent_mask < dma_mask from Benjamin Herrenschmidt
- EEH fixes for SRIOV from Gavin
- Introduce rtas_get_sensor_fast() for IRQ handlers from Thomas Huth
- Use hardware RNG for arch_get_random_seed_* not arch_get_random_* from Paul Mackerras
- Seccomp filter support from Michael Ellerman
- opal_cec_reboot2() handling for HMIs & machine checks from Mahesh Salgaonkar
- Add powerpc timebase as a trace clock source from Naveen N. Rao
- Misc cleanups in the xmon, signal & SLB code from Anshuman Khandual
- Add an inline function to update POWER8 HID0 from Gautham R. Shenoy
- Fix pte_pagesize_index() crash on 4K w/64K hash from Michael Ellerman
- Drop support for 64K local store on 4K kernels from Michael Ellerman
- move dma_get_required_mask() from pnv_phb to pci_controller_ops from Andrew Donnellan
- Initialize distance lookup table from drconf path from Nikunj A Dadhania
- Enable RTC class support from Vaibhav Jain
- Disable automatically blocked PCI config from Gavin Shan
- Add LEDs driver for PowerNV platform from Vasant Hegde
- Fix endianness issues in the HVSI driver from Laurent Dufour
- Kexec endian fixes from Samuel Mendoza-Jonas
- Fix corrupted pdn list from Gavin Shan
- Fix fenced PHB caused by eeh_slot_error_detail() from Gavin Shan
- Freescale updates from Scott: Highlights include 32-bit memcpy/memset
optimizations, checksum optimizations, 85xx config fragments and updates,
device tree updates, e6500 fixes for non-SMP, and misc cleanup and minor
fixes.
- A ton of cxl updates & fixes:
- Add explicit precision specifiers from Rasmus Villemoes
- use more common format specifier from Rasmus Villemoes
- Destroy cxl_adapter_idr on module_exit from Johannes Thumshirn
- Destroy afu->contexts_idr on release of an afu from Johannes Thumshirn
- Compile with -Werror from Daniel Axtens
- EEH support from Daniel Axtens
- Plug irq_bitmap getting leaked in cxl_context from Vaibhav Jain
- Add alternate MMIO error handling from Ian Munsie
- Allow release of contexts which have been OPENED but not STARTED from Andrew Donnellan
- Remove use of macro DEFINE_PCI_DEVICE_TABLE from Vaishali Thakkar
- Release irqs if memory allocation fails from Vaibhav Jain
- Remove racy attempt to force EEH invocation in reset from Daniel Axtens
- Fix + cleanup error paths in cxl_dev_context_init from Ian Munsie
- Fix force unmapping mmaps of contexts allocated through the kernel api from Ian Munsie
- Set up and enable PSL Timebase from Philippe Bergheaud
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=n9+X
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
- support "hybrid" iommu/direct DMA ops for coherent_mask < dma_mask
from Benjamin Herrenschmidt
- EEH fixes for SRIOV from Gavin
- introduce rtas_get_sensor_fast() for IRQ handlers from Thomas Huth
- use hardware RNG for arch_get_random_seed_* not arch_get_random_*
from Paul Mackerras
- seccomp filter support from Michael Ellerman
- opal_cec_reboot2() handling for HMIs & machine checks from Mahesh
Salgaonkar
- add powerpc timebase as a trace clock source from Naveen N. Rao
- misc cleanups in the xmon, signal & SLB code from Anshuman Khandual
- add an inline function to update POWER8 HID0 from Gautham R. Shenoy
- fix pte_pagesize_index() crash on 4K w/64K hash from Michael Ellerman
- drop support for 64K local store on 4K kernels from Michael Ellerman
- move dma_get_required_mask() from pnv_phb to pci_controller_ops from
Andrew Donnellan
- initialize distance lookup table from drconf path from Nikunj A
Dadhania
- enable RTC class support from Vaibhav Jain
- disable automatically blocked PCI config from Gavin Shan
- add LEDs driver for PowerNV platform from Vasant Hegde
- fix endianness issues in the HVSI driver from Laurent Dufour
- kexec endian fixes from Samuel Mendoza-Jonas
- fix corrupted pdn list from Gavin Shan
- fix fenced PHB caused by eeh_slot_error_detail() from Gavin Shan
- Freescale updates from Scott: Highlights include 32-bit memcpy/memset
optimizations, checksum optimizations, 85xx config fragments and
updates, device tree updates, e6500 fixes for non-SMP, and misc
cleanup and minor fixes.
- a ton of cxl updates & fixes:
- add explicit precision specifiers from Rasmus Villemoes
- use more common format specifier from Rasmus Villemoes
- destroy cxl_adapter_idr on module_exit from Johannes Thumshirn
- destroy afu->contexts_idr on release of an afu from Johannes
Thumshirn
- compile with -Werror from Daniel Axtens
- EEH support from Daniel Axtens
- plug irq_bitmap getting leaked in cxl_context from Vaibhav Jain
- add alternate MMIO error handling from Ian Munsie
- allow release of contexts which have been OPENED but not STARTED
from Andrew Donnellan
- remove use of macro DEFINE_PCI_DEVICE_TABLE from Vaishali Thakkar
- release irqs if memory allocation fails from Vaibhav Jain
- remove racy attempt to force EEH invocation in reset from Daniel
Axtens
- fix + cleanup error paths in cxl_dev_context_init from Ian Munsie
- fix force unmapping mmaps of contexts allocated through the kernel
api from Ian Munsie
- set up and enable PSL Timebase from Philippe Bergheaud
* tag 'powerpc-4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (140 commits)
cxl: Set up and enable PSL Timebase
cxl: Fix force unmapping mmaps of contexts allocated through the kernel api
cxl: Fix + cleanup error paths in cxl_dev_context_init
powerpc/eeh: Fix fenced PHB caused by eeh_slot_error_detail()
powerpc/pseries: Cleanup on pci_dn_reconfig_notifier()
powerpc/pseries: Fix corrupted pdn list
powerpc/powernv: Enable LEDS support
powerpc/iommu: Set default DMA offset in dma_dev_setup
cxl: Remove racy attempt to force EEH invocation in reset
cxl: Release irqs if memory allocation fails
cxl: Remove use of macro DEFINE_PCI_DEVICE_TABLE
powerpc/powernv: Fix mis-merge of OPAL support for LEDS driver
powerpc/powernv: Reset HILE before kexec_sequence()
powerpc/kexec: Reset secondary cpu endianness before kexec
powerpc/hvsi: Fix endianness issues in the HVSI driver
leds/powernv: Add driver for PowerNV platform
powerpc/powernv: Create LED platform device
powerpc/powernv: Add OPAL interfaces for accessing and modifying system LED states
powerpc/powernv: Fix the log message when disabling VF
cxl: Allow release of contexts which have been OPENED but not STARTED
...
H. Nikolaus Schaller