commit 286e877181 upstream.
Commit efda1b5d87 ("acpi, nfit, libnvdimm: fix / harden ars_status output length handling")
Introduced additional hardening for ambiguity in the ACPI spec for
ars_status output sizing. However, it had a couple of cases mixed up.
Where it should have been checking for (and returning) "out_field[1] -
4" it was using "out_field[1] - 8" and vice versa.
This caused a four byte discrepancy in the buffer size passed on to
the command handler, and in some cases, this caused memory corruption
like:
./daxdev-errors.sh: line 76: 24104 Aborted (core dumped) ./daxdev-errors $busdev $region
malloc(): memory corruption
Program received signal SIGABRT, Aborted.
[...]
#5 0x00007ffff7865a2e in calloc () from /lib64/libc.so.6
#6 0x00007ffff7bc2970 in ndctl_bus_cmd_new_ars_status (ars_cap=ars_cap@entry=0x6153b0) at ars.c:136
#7 0x0000000000401644 in check_ars_status (check=0x7fffffffdeb0, bus=0x604c20) at daxdev-errors.c:144
#8 test_daxdev_clear_error (region_name=<optimized out>, bus_name=<optimized out>)
at daxdev-errors.c:332
Cc: <stable@vger.kernel.org>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Lukasz Dorau <lukasz.dorau@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Fixes: efda1b5d87 ("acpi, nfit, libnvdimm: fix / harden ars_status output length handling")
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Signed-of-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 254a4cd50b upstream.
The pmem driver does not honor a forced read-only setting for very long:
$ blockdev --setro /dev/pmem0
$ blockdev --getro /dev/pmem0
1
followed by various commands like these:
$ blockdev --rereadpt /dev/pmem0
or
$ mkfs.ext4 /dev/pmem0
results in this in the kernel serial log:
nd_pmem namespace0.0: region0 read-write, marking pmem0 read-write
with the read-only setting lost:
$ blockdev --getro /dev/pmem0
0
That's from bus.c nvdimm_revalidate_disk(), which always applies the
setting from nd_region (which is initially based on the ACPI NFIT
NVDIMM state flags not_armed bit).
In contrast, commit 20bd1d026a ("scsi: sd: Keep disk read-only when
re-reading partition") fixed this issue for SCSI devices to preserve
the previous setting if it was set to read-only.
This patch modifies bus.c to preserve any previous read-only setting.
It also eliminates the kernel serial log print except for cases where
read-write is changed to read-only, so it doesn't print read-only to
read-only non-changes.
Cc: <stable@vger.kernel.org>
Fixes: 5813882094 ("libnvdimm, nfit: handle unarmed dimms, mark namespaces read-only")
Signed-off-by: Robert Elliott <elliott@hpe.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4f8672201b upstream.
The following NULL dereference results from incorrectly assuming that
ndd is valid in this print:
struct nvdimm_drvdata *ndd = to_ndd(&nd_region->mapping[i]);
/*
* Give up if we don't find an instance of a uuid at each
* position (from 0 to nd_region->ndr_mappings - 1), or if we
* find a dimm with two instances of the same uuid.
*/
dev_err(&nd_region->dev, "%s missing label for %pUb\n",
dev_name(ndd->dev), nd_label->uuid);
BUG: unable to handle kernel NULL pointer dereference at 0000000000000000
IP: nd_region_register_namespaces+0xd67/0x13c0 [libnvdimm]
PGD 0 P4D 0
Oops: 0000 [#1] SMP PTI
CPU: 43 PID: 673 Comm: kworker/u609:10 Not tainted 4.16.0-rc4+ #1
[..]
RIP: 0010:nd_region_register_namespaces+0xd67/0x13c0 [libnvdimm]
[..]
Call Trace:
? devres_add+0x2f/0x40
? devm_kmalloc+0x52/0x60
? nd_region_activate+0x9c/0x320 [libnvdimm]
nd_region_probe+0x94/0x260 [libnvdimm]
? kernfs_add_one+0xe4/0x130
nvdimm_bus_probe+0x63/0x100 [libnvdimm]
Switch to using the nvdimm device directly.
Fixes: 0e3b0d123c ("libnvdimm, namespace: allow multiple pmem...")
Cc: <stable@vger.kernel.org>
Reported-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c31898c8c7 upstream.
At initialization time the 'dimm' driver caches a copy of the memory
device's label area and reserves address space for each of the
namespaces defined.
However, as can be seen below, the reservation occurs even when the
index blocks are invalid:
nvdimm nmem0: nvdimm_init_config_data: len: 131072 rc: 0
nvdimm nmem0: config data size: 131072
nvdimm nmem0: __nd_label_validate: nsindex0 labelsize 1 invalid
nvdimm nmem0: __nd_label_validate: nsindex1 labelsize 1 invalid
nvdimm nmem0: : pmem-6025e505: 0x1000000000 @ 0xf50000000 reserve <-- bad
Gate dpa reservation on the presence of valid index blocks.
Cc: <stable@vger.kernel.org>
Fixes: 4a826c83db ("libnvdimm: namespace indices: read and validate")
Reported-by: Krzysztof Rusocki <krzysztof.rusocki@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3ffb0ba9b5 upstream.
Prior to 25520d55cd ("block: Inline blk_integrity in struct gendisk")
we needed to temporarily add a zero-capacity disk before registering for
blk-integrity. But adding a zero-capacity disk caused the partition
table scanning to bail early, and this resulted in partitions not coming
up after a probe of the BTT or blk namespaces.
We can now register for integrity before the disk has been added, and
this fixes the rescan problems.
Fixes: 25520d55cd ("block: Inline blk_integrity in struct gendisk")
Reported-by: Dariusz Dokupil <dariusz.dokupil@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 19deaa217b upstream.
The alignment checks at pfn driver startup fail to properly account for
the 'start_pad' in the case where the namespace is misaligned relative
to its internal alignment. This is typically triggered in 1G aligned
namespace, but could theoretically trigger with small namespace
alignments. When this triggers the kernel reports messages of the form:
dax2.1: bad offset: 0x3c000000 dax disabled align: 0x40000000
Fixes: 1ee6667cd8 ("libnvdimm, pfn, dax: fix initialization vs autodetect...")
Reported-by: Jane Chu <jane.chu@oracle.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 24e3a7fb60 upstream.
Due to a spec misinterpretation, the Linux implementation of the BTT log
area had different padding scheme from other implementations, such as
UEFI and NVML.
This fixes the padding scheme, and defaults to it for new BTT layouts.
We attempt to detect the padding scheme in use when probing for an
existing BTT. If we detect the older/incompatible scheme, we continue
using it.
Reported-by: Juston Li <juston.li@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Fixes: 5212e11fde ("nd_btt: atomic sector updates")
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 41fce90f26 upstream.
The following namespace configuration attempt:
# ndctl create-namespace -e namespace0.0 -m devdax -a 1G -f
libndctl: ndctl_dax_enable: dax0.1: failed to enable
Error: namespace0.0: failed to enable
failed to reconfigure namespace: No such device or address
...fails when the backing memory range is not physically aligned to 1G:
# cat /proc/iomem | grep Persistent
210000000-30fffffff : Persistent Memory (legacy)
In the above example the 4G persistent memory range starts and ends on a
256MB boundary.
We handle this case correctly when needing to handle cases that violate
section alignment (128MB) collisions against "System RAM", and we simply
need to extend that padding/truncation for the 1GB alignment use case.
Fixes: 315c562536 ("libnvdimm, pfn: add 'align' attribute...")
Reported-and-tested-by: Jane Chu <jane.chu@oracle.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c1fb354207 upstream.
For the same reason that /proc/iomem returns 0's for non-root readers
and acpi tables are root-only, make the 'resource' attribute for
namespace devices only readable by root. Otherwise we disclose physical
address information.
Fixes: bf9bccc14c ("libnvdimm: pmem label sets and namespace instantiation")
Reported-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b8ff981f88 upstream.
For the same reason that /proc/iomem returns 0's for non-root readers
and acpi tables are root-only, make the 'resource' attribute for region
devices only readable by root. Otherwise we disclose physical address
information.
Fixes: 802f4be6fe ("libnvdimm: Add 'resource' sysfs attribute to regions")
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Reported-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b18d4b8a25 upstream.
The set of valid sequence numbers is {1,2,3}. The specification
indicates that an implementation should consider 0 a sign of a critical
error:
UEFI 2.7: 13.19 NVDIMM Label Protocol
Software never writes the sequence number 00, so a correctly
check-summed Index Block with this sequence number probably indicates a
critical error. When software discovers this case it treats it as an
invalid Index Block indication.
While the expectation is that the invalid block is just thrown away, the
Robustness Principle says we should fix this to make both sequence
numbers valid.
Fixes: f524bf271a ("libnvdimm: write pmem label set")
Reported-by: Juston Li <juston.li@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 26417ae4fc upstream.
For the same reason that /proc/iomem returns 0's for non-root readers
and acpi tables are root-only, make the 'resource' attribute for pfn
devices only readable by root. Otherwise we disclose physical address
information.
Fixes: f6ed58c70d ("libnvdimm, pfn: 'resource'-address and 'size'...")
Reported-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d34cb80840 upstream.
If we successfully enable a DIMM then it must not be locked and we can
clear the label-read failure condition. Otherwise, we need to reload the
entire bus provider driver to achieve the same effect, and that can
disrupt unrelated DIMMs and namespaces.
Fixes: 9d62ed9651 ("libnvdimm: handle locked label storage areas")
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Maurice reports:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000028
IP: holder_class_store+0x253/0x2b0 [libnvdimm]
...while trying to reconfigure an NVDIMM-N namespace into 'sector' /
'btt' mode. The crash points to this line:
(gdb) li *(holder_class_store+0x253)
0x7773 is in holder_class_store (drivers/nvdimm/namespace_devs.c:1420).
1415 for (i = 0; i < nd_region->ndr_mappings; i++) {
1416 struct nd_mapping *nd_mapping = &nd_region->mapping[i];
1417 struct nvdimm_drvdata *ndd = to_ndd(nd_mapping);
1418 struct nd_namespace_index *nsindex;
1419
1420 nsindex = to_namespace_index(ndd, ndd->ns_current);
...where we are failing because ndd is NULL due to NVDIMM-N dimms not
supporting labels.
Long story short, default to the BTTv1 format in the label-less /
NVDIMM-N case.
Fixes: 14e4945426 ("libnvdimm, btt: BTT updates for UEFI 2.7 format")
Cc: <stable@vger.kernel.org>
Cc: Vishal Verma <vishal.l.verma@intel.com>
Reported-by: Maurice A. Saldivar <maurice.a.saldivar@hpe.com>
Tested-by: Maurice A. Saldivar <maurice.a.saldivar@hpe.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
- Constify a few variables in DM core and DM integrity
- Add bufio optimization and checksum failure accounting to DM integrity
- Fix DM integrity to avoid checking integrity of failed reads
- Fix DM integrity to use init_completion
- A couple DM log-writes target fixes
- Simplify DAX flushing by eliminating the unnecessary flush abstraction
that was stood up for DM's use.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZuo8UAAoJEMUj8QotnQNa5BEIANO4mHh1nrzEbH72a4RCLgxV
H1Pk1zZx/W1bhOOmcRRhxCSM85dPgsCegc5EmpwLZEMavQrP9UZblHcYOUsyIx7W
S/lWa+soOq/5N2OveROc4WdoWVs50UFmc1+BcClc4YrEe+15XC3R0VMkjX2b/hUL
o2eYhPjpMlgaorMtRRU6MAooo2fBRQ9m05aPeVgd35fxibrE7PZm+EYW09wa0STi
9ufuDXJf8+TtFP/38BD41LbUEskuHUZTSDeAJ+3DBaTtfEZcZYxsst4P9JangsHx
jqqqI9aYzFD2a27fl9WLhCvm40YFiKp5nwzED0RZjzWxVa/jTShX7a49BdzTTfw=
=rkSB
-----END PGP SIGNATURE-----
Merge tag 'for-4.14/dm-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper updates from Mike Snitzer:
- Some request-based DM core and DM multipath fixes and cleanups
- Constify a few variables in DM core and DM integrity
- Add bufio optimization and checksum failure accounting to DM
integrity
- Fix DM integrity to avoid checking integrity of failed reads
- Fix DM integrity to use init_completion
- A couple DM log-writes target fixes
- Simplify DAX flushing by eliminating the unnecessary flush
abstraction that was stood up for DM's use.
* tag 'for-4.14/dm-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dax: remove the pmem_dax_ops->flush abstraction
dm integrity: use init_completion instead of COMPLETION_INITIALIZER_ONSTACK
dm integrity: make blk_integrity_profile structure const
dm integrity: do not check integrity for failed read operations
dm log writes: fix >512b sectorsize support
dm log writes: don't use all the cpu while waiting to log blocks
dm ioctl: constify ioctl lookup table
dm: constify argument arrays
dm integrity: count and display checksum failures
dm integrity: optimize writing dm-bufio buffers that are partially changed
dm rq: do not update rq partially in each ending bio
dm rq: make dm-sq requeuing behavior consistent with dm-mq behavior
dm mpath: complain about unsupported __multipath_map_bio() return values
dm mpath: avoid that building with W=1 causes gcc 7 to complain about fall-through
* Media error handling support in the Block Translation Table (BTT)
driver is reworked to address sleeping-while-atomic locking and
memory-allocation-context conflicts.
* The dax_device lookup overhead for xfs and ext4 is moved out of the
iomap hot-path to a mount-time lookup.
* A new 'ecc_unit_size' sysfs attribute is added to advertise the
read-modify-write boundary property of a persistent memory range.
* Preparatory fix-ups for arm and powerpc pmem support are included
along with other miscellaneous fixes.
-----BEGIN PGP SIGNATURE-----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=5iGY
-----END PGP SIGNATURE-----
Merge tag 'libnvdimm-for-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm from Dan Williams:
"A rework of media error handling in the BTT driver and other updates.
It has appeared in a few -next releases and collected some late-
breaking build-error and warning fixups as a result.
Summary:
- Media error handling support in the Block Translation Table (BTT)
driver is reworked to address sleeping-while-atomic locking and
memory-allocation-context conflicts.
- The dax_device lookup overhead for xfs and ext4 is moved out of the
iomap hot-path to a mount-time lookup.
- A new 'ecc_unit_size' sysfs attribute is added to advertise the
read-modify-write boundary property of a persistent memory range.
- Preparatory fix-ups for arm and powerpc pmem support are included
along with other miscellaneous fixes"
* tag 'libnvdimm-for-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: (26 commits)
libnvdimm, btt: fix format string warnings
libnvdimm, btt: clean up warning and error messages
ext4: fix null pointer dereference on sbi
libnvdimm, nfit: move the check on nd_reserved2 to the endpoint
dax: fix FS_DAX=n BLOCK=y compilation
libnvdimm: fix integer overflow static analysis warning
libnvdimm, nd_blk: remove mmio_flush_range()
libnvdimm, btt: rework error clearing
libnvdimm: fix potential deadlock while clearing errors
libnvdimm, btt: cache sector_size in arena_info
libnvdimm, btt: ensure that flags were also unchanged during a map_read
libnvdimm, btt: refactor map entry operations with macros
libnvdimm, btt: fix a missed NVDIMM_IO_ATOMIC case in the write path
libnvdimm, nfit: export an 'ecc_unit_size' sysfs attribute
ext4: perform dax_device lookup at mount
ext2: perform dax_device lookup at mount
xfs: perform dax_device lookup at mount
dax: introduce a fs_dax_get_by_bdev() helper
libnvdimm, btt: check memory allocation failure
libnvdimm, label: fix index block size calculation
...
Commit abebfbe2f7 ("dm: add ->flush() dax operation support") is
buggy. A DM device may be composed of multiple underlying devices and
all of them need to be flushed. That commit just routes the flush
request to the first device and ignores the other devices.
It could be fixed by adding more complex logic to the device mapper. But
there is only one implementation of the method pmem_dax_ops->flush - that
is pmem_dax_flush() - and it calls arch_wb_cache_pmem(). Consequently, we
don't need the pmem_dax_ops->flush abstraction at all, we can call
arch_wb_cache_pmem() directly from dax_flush() because dax_dev->ops->flush
can't ever reach anything different from arch_wb_cache_pmem().
It should be also pointed out that for some uses of persistent memory it
is needed to flush only a very small amount of data (such as 1 cacheline),
and it would be overkill if we go through that device mapper machinery for
a single flushed cache line.
Fix this by removing the pmem_dax_ops->flush abstraction and call
arch_wb_cache_pmem() directly from dax_flush(). Also, remove the device
mapper code that forwards the flushes.
Fixes: abebfbe2f7 ("dm: add ->flush() dax operation support")
Cc: stable@vger.kernel.org
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Fix format warnings (seen on i386) in nvdimm/btt.c:
../drivers/nvdimm/btt.c: In function ‘btt_map_init’:
../drivers/nvdimm/btt.c:430:3: warning: format ‘%lx’ expects argument of type ‘long unsigned int’, but argument 4 has type ‘size_t’ [-Wformat=]
dev_WARN_ONCE(to_dev(arena), size < 512,
^
../drivers/nvdimm/btt.c: In function ‘btt_log_init’:
../drivers/nvdimm/btt.c:474:3: warning: format ‘%lx’ expects argument of type ‘long unsigned int’, but argument 4 has type ‘size_t’ [-Wformat=]
dev_WARN_ONCE(to_dev(arena), size < 512,
^
Fixes: 86652d2eb3 ("libnvdimm, btt: clean up warning and error messages")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Convert all WARN* style messages to dev_WARN, and for errors in the IO
paths, use dev_err_ratelimited. Also remove some BUG_ONs in the IO path
and replace them with the above - no need to crash the machine in case
of an unaligned IO.
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Pull block layer updates from Jens Axboe:
"This is the first pull request for 4.14, containing most of the code
changes. It's a quiet series this round, which I think we needed after
the churn of the last few series. This contains:
- Fix for a registration race in loop, from Anton Volkov.
- Overflow complaint fix from Arnd for DAC960.
- Series of drbd changes from the usual suspects.
- Conversion of the stec/skd driver to blk-mq. From Bart.
- A few BFQ improvements/fixes from Paolo.
- CFQ improvement from Ritesh, allowing idling for group idle.
- A few fixes found by Dan's smatch, courtesy of Dan.
- A warning fixup for a race between changing the IO scheduler and
device remova. From David Jeffery.
- A few nbd fixes from Josef.
- Support for cgroup info in blktrace, from Shaohua.
- Also from Shaohua, new features in the null_blk driver to allow it
to actually hold data, among other things.
- Various corner cases and error handling fixes from Weiping Zhang.
- Improvements to the IO stats tracking for blk-mq from me. Can
drastically improve performance for fast devices and/or big
machines.
- Series from Christoph removing bi_bdev as being needed for IO
submission, in preparation for nvme multipathing code.
- Series from Bart, including various cleanups and fixes for switch
fall through case complaints"
* 'for-4.14/block' of git://git.kernel.dk/linux-block: (162 commits)
kernfs: checking for IS_ERR() instead of NULL
drbd: remove BIOSET_NEED_RESCUER flag from drbd_{md_,}io_bio_set
drbd: Fix allyesconfig build, fix recent commit
drbd: switch from kmalloc() to kmalloc_array()
drbd: abort drbd_start_resync if there is no connection
drbd: move global variables to drbd namespace and make some static
drbd: rename "usermode_helper" to "drbd_usermode_helper"
drbd: fix race between handshake and admin disconnect/down
drbd: fix potential deadlock when trying to detach during handshake
drbd: A single dot should be put into a sequence.
drbd: fix rmmod cleanup, remove _all_ debugfs entries
drbd: Use setup_timer() instead of init_timer() to simplify the code.
drbd: fix potential get_ldev/put_ldev refcount imbalance during attach
drbd: new disk-option disable-write-same
drbd: Fix resource role for newly created resources in events2
drbd: mark symbols static where possible
drbd: Send P_NEG_ACK upon write error in protocol != C
drbd: add explicit plugging when submitting batches
drbd: change list_for_each_safe to while(list_first_entry_or_null)
drbd: introduce drbd_recv_header_maybe_unplug
...
The .rw_page in struct block_device_operations is used by the swap
subsystem to read/write the page contents from/into the corresponding
swap slot in the swap device. To support the THP (Transparent Huge
Page) swap optimization, the .rw_page is enhanced to support to
read/write THP if possible.
Link: http://lkml.kernel.org/r/20170724051840.2309-6-ying.huang@intel.com
Signed-off-by: "Huang, Ying" <ying.huang@intel.com>
Reviewed-by: Ross Zwisler <ross.zwisler@intel.com> [for brd.c, zram_drv.c, pmem.c]
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Vishal L Verma <vishal.l.verma@intel.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: "Kirill A . Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Shaohua Li <shli@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Delay the check of nd_reserved2 to the actual endpoint (acpi_nfit_ctl)
that uses it, as a prevention of a potential double-fetch bug.
While examining the kernel source code, I found a dangerous operation that
could turn into a double-fetch situation (a race condition bug) where
the same userspace memory region are fetched twice into kernel with sanity
checks after the first fetch while missing checks after the second fetch.
In the case of _IOC_NR(ioctl_cmd) == ND_CMD_CALL:
1. The first fetch happens in line 935 copy_from_user(&pkg, p, sizeof(pkg)
2. subsequently `pkg.nd_reserved2` is asserted to be all zeroes
(line 984 to 986).
3. The second fetch happens in line 1022 copy_from_user(buf, p, buf_len)
4. Given that `p` can be fully controlled in userspace, an attacker can
race condition to override the header part of `p`, say,
`((struct nd_cmd_pkg *)p)->nd_reserved2` to arbitrary value
(say nine 0xFFFFFFFF for `nd_reserved2`) after the first fetch but before the
second fetch. The changed value will be copied to `buf`.
5. There is no checks on the second fetches until the use of it in
line 1034: nd_cmd_clear_to_send(nvdimm_bus, nvdimm, cmd, buf) and
line 1038: nd_desc->ndctl(nd_desc, nvdimm, cmd, buf, buf_len, &cmd_rc)
which means that the assumed relation, `p->nd_reserved2` are all zeroes might
not hold after the second fetch. And once the control goes to these functions
we lose the context to assert the assumed relation.
6. Based on my manual analysis, `p->nd_reserved2` is not used in function
`nd_cmd_clear_to_send` and potential implementations of `nd_desc->ndctl`
so there is no working exploit against it right now. However, this could
easily turns to an exploitable one if careless developers start to use
`p->nd_reserved2` later and assume that they are all zeroes.
Move the validation of the nd_reserved2 field to the ->ndctl()
implementation where it has a stable buffer to evaluate.
Signed-off-by: Meng Xu <mengxu.gatech@gmail.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Dan reports:
The patch 62232e45f4a2: "libnvdimm: control (ioctl) messages for
nvdimm_bus and nvdimm devices" from Jun 8, 2015, leads to the
following static checker warning:
drivers/nvdimm/bus.c:1018 __nd_ioctl()
warn: integer overflows 'buf_len'
From a casual review, this seems like it might be a real bug. On
the first iteration we load some data into in_env[]. On the second
iteration we read a use controlled "in_size" from nd_cmd_in_size().
It can go up to UINT_MAX - 1. A high number means we will fill the
whole in_env[] buffer. But we potentially keep looping and adding
more to in_len so now it can be any value.
It simple enough to change, but it feels weird that we keep looping
even though in_env is totally full. Shouldn't we just return an
error if we don't have space for desc->in_num.
We keep looping because the size of the total input is allowed to be
bigger than the 'envelope' which is a subset of the payload that tells
us how much data to expect. For safety explicitly check that buf_len
does not overflow which is what the checker flagged.
Cc: <stable@vger.kernel.org>
Fixes: 62232e45f4a2: "libnvdimm: control (ioctl) messages for nvdimm_bus..."
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
mmio_flush_range() suffers from a lack of clearly-defined semantics,
and is somewhat ambiguous to port to other architectures where the
scope of the writeback implied by "flush" and ordering might matter,
but MMIO would tend to imply non-cacheable anyway. Per the rationale
in 67a3e8fe90 ("nd_blk: change aperture mapping from WC to WB"), the
only existing use is actually to invalidate clean cache lines for
ARCH_MEMREMAP_PMEM type mappings *without* writeback. Since the recent
cleanup of the pmem API, that also now happens to be the exact purpose
of arch_invalidate_pmem(), which would be a far more well-defined tool
for the job.
Rather than risk potentially inconsistent implementations of
mmio_flush_range() for the sake of one callsite, streamline things by
removing it entirely and instead move the ARCH_MEMREMAP_PMEM related
definitions up to the libnvdimm level, so they can be shared by NFIT
as well. This allows NFIT to be enabled for arm64.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Clearing errors or badblocks during a BTT write requires sending an ACPI
DSM, which means potentially sleeping. Since a BTT IO happens in atomic
context (preemption disabled, spinlocks may be held), we cannot perform
error clearing in the course of an IO. Due to this error clearing for
BTT IOs has hitherto been disabled.
In this patch we move error clearing out of the atomic section, and thus
re-enable error clearing with BTTs. When we are about to add a block to
the free list, we check if it was previously marked as an error, and if
it was, we add it to the freelist, but also set a flag that says error
clearing will be required. We then drop the lane (ending the atomic
context), and send a zero buffer so that the error can be cleared. The
error flag in the free list is protected by the nd 'lane', and is set
only be a thread while it holds that lane. When the error is cleared,
the flag is cleared, but while holding a mutex for that freelist index.
When writing, we check for two things -
1/ If the freelist mutex is held or if the error flag is set. If so,
this is an error block that is being (or about to be) cleared.
2/ If the block is a known badblock based on nsio->bb
The second check is required because the BTT map error flag for a map
entry only gets set when an error LBA is read. If we write to a new
location that may not have the map error flag set, but still might be in
the region's badblock list, we can trigger an EIO on the write, which is
undesirable and completely avoidable.
Cc: Jeff Moyer <jmoyer@redhat.com>
Cc: Toshi Kani <toshi.kani@hpe.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
With the ACPI NFIT 'DSM' methods, acpi can be called from IO paths.
Specifically, the DSM to clear media errors is called during writes, so
that we can provide a writes-fix-errors model.
However it is easy to imagine a scenario like:
-> write through the nvdimm driver
-> acpi allocation
-> writeback, causes more IO through the nvdimm driver
-> deadlock
Fix this by using memalloc_noio_{save,restore}, which sets the GFP_NOIO
flag for the current scope when issuing commands/IOs that are expected
to clear errors.
Cc: <linux-acpi@vger.kernel.org>
Cc: <linux-nvdimm@lists.01.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Robert Moore <robert.moore@intel.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In preparation for the error clearing rework, add sector_size in the
arena_info struct.
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In btt_map_read, we read the map twice to make sure that the map entry
didn't change after we added it to the read tracking table. In
anticipation of expanding the use of the error bit, also make sure that
the error and zero flags are constant across the two map reads.
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Add helpers for converting a raw map entry to just the block number, or
either of the 'e' or 'z' flags in preparation for actually using the
error flag to mark blocks with media errors.
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The IO context conversion for rw_bytes missed a case in the BTT write
path (btt_map_write) which should've been marked as atomic.
In reality this should not cause a problem, because map writes are to
small for nsio_rw_bytes to attempt error clearing, but it should be
fixed for posterity.
Add a might_sleep() in the non-atomic section of nsio_rw_bytes so that
things like the nfit unit tests, which don't actually sleep, can catch
bugs like this.
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Check memory allocation failures and return -ENOMEM in such cases, as
already done few lines below for another memory allocation.
This avoids NULL pointers dereference.
Cc: <stable@vger.kernel.org>
Fixes: 14e4945426 ("libnvdimm, btt: BTT updates for UEFI 2.7 format")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The old calculation assumed that the label space was 128k and the label
size is 128. With v1.2 labels where the label size is 256 this
calculation will return zero. We are saved by the fact that the
nsindex_size is always pre-initialized from a previous 128 byte
assumption and we are lucky that the index sizes turn out the same.
Fix this going forward in case we start encountering different
geometries of label areas besides 128k.
Since the label size can change from one call to the next, drop the
caching of nsindex_size.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This way we don't need a block_device structure to submit I/O. The
block_device has different life time rules from the gendisk and
request_queue and is usually only available when the block device node
is open. Other callers need to explicitly create one (e.g. the lightnvm
passthrough code, or the new nvme multipathing code).
For the actual I/O path all that we need is the gendisk, which exists
once per block device. But given that the block layer also does
partition remapping we additionally need a partition index, which is
used for said remapping in generic_make_request.
Note that all the block drivers generally want request_queue or
sometimes the gendisk, so this removes a layer of indirection all
over the stack.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Now that we properly advertise the supported pte, pmd, and pud sizes,
restrict the supported alignments that can be set on a namespace. This
assumes that userspace was not previously relying on the ability to set
odd alignments. At least ndctl only ever supported setting the namespace
alignment to 4K, 2M, or 1G.
Cc: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The alignment of a DAX and PFN regions dictates the page sizes that can
be used to map the region. Even if the hardware page sizes are known the
actual range of supported page sizes that can be used with DAX depends
on the kernel configuration. As a result it's best that the kernel
advertises the alignments that should be used with these region types.
This patch adds the 'supported_alignments' region attribute to expose
this information to userspace.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
[djbw: integrate with nd_size_select_show() rename and other fixups]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Prepare for other another consumer of this size selection scheme that is
not a 'sector size'.
Cc: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
No functional change in this patch, just in preparation for
basing the inflight mechanism on the queue in question.
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
It is useful to be able to know the position of a DIMM in an
interleave-set. Consider the case where the order of the DIMMs changes
causing a namespace to be invalidated because the interleave-set cookie no
longer matches. If the before and after state of each DIMM position is
known this state debugged by the system owner.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Currently libnvdimm uses HPAGE_SIZE as the default alignment for DAX and
PFN devices. HPAGE_SIZE is the default hugetlbfs page size and when
hugetlbfs is disabled it defaults to PAGE_SIZE. Given DAX has more
in common with THP than hugetlbfs we should proably be using
HPAGE_PMD_SIZE, but this is undefined when THP is disabled so lets just
give it a new name.
The other usage of HPAGE_SIZE in libnvdimm is when determining how large
the altmap should be. For the reasons mentioned above it doesn't really
make sense to use HPAGE_SIZE here either. PMD_SIZE seems to be safe to
use in generic code and it happens to match the vmemmap allocation block
on x86 and Power. It's still a hack, but it's a slightly nicer hack.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
__add_badblock_range() does not account sector alignment when
it sets 'num_sectors'. Therefore, an ARS error record range
spanning across two sectors is set to a single sector length,
which leaves the 2nd sector unprotected.
Change __add_badblock_range() to set 'num_sectors' properly.
Cc: <stable@vger.kernel.org>
Fixes: 0caeef63e6 ("libnvdimm: Add a poison list and export badblocks")
Signed-off-by: Toshi Kani <toshi.kani@hpe.com>
Reviewed-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Pull more block updates from Jens Axboe:
"This is a followup for block changes, that didn't make the initial
pull request. It's a bit of a mixed bag, this contains:
- A followup pull request from Sagi for NVMe. Outside of fixups for
NVMe, it also includes a series for ensuring that we properly
quiesce hardware queues when browsing live tags.
- Set of integrity fixes from Dmitry (mostly), fixing various issues
for folks using DIF/DIX.
- Fix for a bug introduced in cciss, with the req init changes. From
Christoph.
- Fix for a bug in BFQ, from Paolo.
- Two followup fixes for lightnvm/pblk from Javier.
- Depth fix from Ming for blk-mq-sched.
- Also from Ming, performance fix for mtip32xx that was introduced
with the dynamic initialization of commands"
* 'for-linus' of git://git.kernel.dk/linux-block: (44 commits)
block: call bio_uninit in bio_endio
nvmet: avoid unneeded assignment of submit_bio return value
nvme-pci: add module parameter for io queue depth
nvme-pci: compile warnings in nvme_alloc_host_mem()
nvmet_fc: Accept variable pad lengths on Create Association LS
nvme_fc/nvmet_fc: revise Create Association descriptor length
lightnvm: pblk: remove unnecessary checks
lightnvm: pblk: control I/O flow also on tear down
cciss: initialize struct scsi_req
null_blk: fix error flow for shared tags during module_init
block: Fix __blkdev_issue_zeroout loop
nvme-rdma: unconditionally recycle the request mr
nvme: split nvme_uninit_ctrl into stop and uninit
virtio_blk: quiesce/unquiesce live IO when entering PM states
mtip32xx: quiesce request queues to make sure no submissions are inflight
nbd: quiesce request queues to make sure no submissions are inflight
nvme: kick requeue list when requeueing a request instead of when starting the queues
nvme-pci: quiesce/unquiesce admin_q instead of start/stop its hw queues
nvme-loop: quiesce/unquiesce admin_q instead of start/stop its hw queues
nvme-fc: quiesce/unquiesce admin_q instead of start/stop its hw queues
...
* Introduce the _flushcache() family of memory copy helpers and use them
for persistent memory write operations on x86. The _flushcache()
semantic indicates that the cache is either bypassed for the copy
operation (movnt) or any lines dirtied by the copy operation are
written back (clwb, clflushopt, or clflush).
* Extend dax_operations with ->copy_from_iter() and ->flush()
operations. These operations and other infrastructure updates allow
all persistent memory specific dax functionality to be pushed into
libnvdimm and the pmem driver directly. It also allows dax-specific
sysfs attributes to be linked to a host device, for example:
/sys/block/pmem0/dax/write_cache
* Add support for the new NVDIMM platform/firmware mechanisms introduced
in ACPI 6.2 and UEFI 2.7. This support includes the v1.2 namespace
label format, extensions to the address-range-scrub command set, new
error injection commands, and a new BTT (block-translation-table)
layout. These updates support inter-OS and pre-OS compatibility.
* Fix a longstanding memory corruption bug in nfit_test.
* Make the pmem and nvdimm-region 'badblocks' sysfs files poll(2)
capable.
* Miscellaneous fixes and small updates across libnvdimm and the nfit
driver.
Acknowledgements that came after the branch was pushed:
commit 6aa734a2f3 "libnvdimm, region, pmem: fix 'badblocks'
sysfs_get_dirent() reference lifetime"
Reviewed-by: Toshi Kani <toshi.kani@hpe.com>
-----BEGIN PGP SIGNATURE-----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=xKQB
-----END PGP SIGNATURE-----
Merge tag 'libnvdimm-for-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm updates from Dan Williams:
"libnvdimm updates for the latest ACPI and UEFI specifications. This
pull request also includes new 'struct dax_operations' enabling to
undo the abuse of copy_user_nocache() for copy operations to pmem.
The dax work originally missed 4.12 to address concerns raised by Al.
Summary:
- Introduce the _flushcache() family of memory copy helpers and use
them for persistent memory write operations on x86. The
_flushcache() semantic indicates that the cache is either bypassed
for the copy operation (movnt) or any lines dirtied by the copy
operation are written back (clwb, clflushopt, or clflush).
- Extend dax_operations with ->copy_from_iter() and ->flush()
operations. These operations and other infrastructure updates allow
all persistent memory specific dax functionality to be pushed into
libnvdimm and the pmem driver directly. It also allows dax-specific
sysfs attributes to be linked to a host device, for example:
/sys/block/pmem0/dax/write_cache
- Add support for the new NVDIMM platform/firmware mechanisms
introduced in ACPI 6.2 and UEFI 2.7. This support includes the v1.2
namespace label format, extensions to the address-range-scrub
command set, new error injection commands, and a new BTT
(block-translation-table) layout. These updates support inter-OS
and pre-OS compatibility.
- Fix a longstanding memory corruption bug in nfit_test.
- Make the pmem and nvdimm-region 'badblocks' sysfs files poll(2)
capable.
- Miscellaneous fixes and small updates across libnvdimm and the nfit
driver.
Acknowledgements that came after the branch was pushed: commit
6aa734a2f3 ("libnvdimm, region, pmem: fix 'badblocks'
sysfs_get_dirent() reference lifetime") was reviewed by Toshi Kani
<toshi.kani@hpe.com>"
* tag 'libnvdimm-for-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: (42 commits)
libnvdimm, namespace: record 'lbasize' for pmem namespaces
acpi/nfit: Issue Start ARS to retrieve existing records
libnvdimm: New ACPI 6.2 DSM functions
acpi, nfit: Show bus_dsm_mask in sysfs
libnvdimm, acpi, nfit: Add bus level dsm mask for pass thru.
acpi, nfit: Enable DSM pass thru for root functions.
libnvdimm: passthru functions clear to send
libnvdimm, btt: convert some info messages to warn/err
libnvdimm, region, pmem: fix 'badblocks' sysfs_get_dirent() reference lifetime
libnvdimm: fix the clear-error check in nsio_rw_bytes
libnvdimm, btt: fix btt_rw_page not returning errors
acpi, nfit: quiet invalid block-aperture-region warnings
libnvdimm, btt: BTT updates for UEFI 2.7 format
acpi, nfit: constify *_attribute_group
libnvdimm, pmem: disable dax flushing when pmem is fronting a volatile region
libnvdimm, pmem, dax: export a cache control attribute
dax: convert to bitmask for flags
dax: remove default copy_from_iter fallback
libnvdimm, nfit: enable support for volatile ranges
libnvdimm, pmem: fix persistence warning
...
Commit f979b13c3c "libnvdimm, label: honor the lba size specified in
v1.2 labels") neglected to update the 'lbasize' in the label when the
namespace sector_size attribute was written. We need this value in the
label for inter-OS / pre-OS compatibility.
Fixes: f979b13c3c ("libnvdimm, label: honor the lba size specified in v1.2 labels")
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Currently if some one try to advance bvec beyond it's size we simply
dump WARN_ONCE and continue to iterate beyond bvec array boundaries.
This simply means that we endup dereferencing/corrupting random memory
region.
Sane reaction would be to propagate error back to calling context
But bvec_iter_advance's calling context is not always good for error
handling. For safity reason let truncate iterator size to zero which
will break external iteration loop which prevent us from unpredictable
memory range corruption. And even it caller ignores an error, it will
corrupt it's own bvecs, not others.
This patch does:
- Return error back to caller with hope that it will react on this
- Truncate iterator size
Code was added long time ago here 4550dd6c, luckily no one hit it
in real life :)
Signed-off-by: Dmitry Monakhov <dmonakhov@openvz.org>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
[hch: switch to true/false returns instead of errno values]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Currently all integrity prep hooks are open-coded, and if prepare fails
we ignore it's code and fail bio with EIO. Let's return real error to
upper layer, so later caller may react accordingly.
In fact no one want to use bio_integrity_prep() w/o bio_integrity_enabled,
so it is reasonable to fold it in to one function.
Signed-off-by: Dmitry Monakhov <dmonakhov@openvz.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
[hch: merged with the latest block tree,
return bool from bio_integrity_prep]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Have dsm functions called via the pass thru mechanism also
be checked against clear to send.
Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Some critical messages such as IO errors, metadata failures were printed
with dev_info. Make them louder by upgrading them to dev_warn or
dev_error.
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
We need to hold a reference on the 'dirent' until we are sure there are
no more notifications that will be sent. As noted in the new comments we
take advantage of the fact that the references are taken and dropped
under device_lock() and that nd_device_notify() holds device_lock() over
new badblocks notifications. The notifications that happen when
badblocks are cleared only occur while the device is active.
Also take the opportunity to fix up the error messages to report the
user visible effect of a sysfs_get_dirent() failure.
Fixes: 975750a98c ("libnvdimm, pmem: Add sysfs notifications to badblocks")
Cc: Toshi Kani <toshi.kani@hpe.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Vishal Verma