cherry-pick below patch:
ENGR00277663-3 power: sabresd_battery: remove check charger offset on mx6slevk
No need check the charger offset on mx6slevk, since there is no adc converter
Signed-off-by: Robin Gong <b38343@freescale.com>
(cherry picked from commit 7683c62cf2290629f09983744d5a3987a4d64669)
(cherry picked from commit 5f29715585ae82a435aa5ba0fe6393a53c10f87d)
cherry-pick below patch:
ENGR00275004-4: power: sabresd_battery: add sabresd_battery driver
Add sabresd battery driver which based on Max8903 charger IC.
Signed-off-by: Robin Gong <b38343@freescale.com>
[ Upstream commit 09bebb1adb ]
Vexpress platforms provide two different restart handlers: SYS_REBOOT
that restart the entire system, while DB_RESET only restarts the
daughter board containing the CPU. DB_RESET is overridden by SYS_REBOOT
if it exists.
notifier_chain_register used in register_restart_handler by design
relies on notifiers to be registered once only, however vexpress restart
notifier can get registered twice. When this happen it corrupts list
of notifiers, as result some notifiers can be not called on proper
event, traverse on list can be cycled forever, and second unregister
can access already freed memory.
So far, since this was the only restart handler in the system, no issue
was observed even if the same notifier was registered twice. However
commit 6c5c0d48b6 ("watchdog: sp805: add restart handler") added
support for SP805 restart handlers and since the system under test
contains two vexpress restart and two SP805 watchdog instances, it was
observed that during the boot traversing the restart handler list looped
forever as there's a cycle in that list resulting in boot hang.
This patch fixes the issues by ensuring that the notifier is installed
only once.
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Fixes: 46c99ac662 ("power/reset: vexpress: Register with kernel restart handler")
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f2a42595f0 ]
We should look at val which contains the value read from the register,
not ret which is always 0 on a successful read.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Fixes: eac53b3664 ("power: supply: axp288_charger: Drop platform_data dependency")
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a427503eda upstream.
If an iio channel defines a basic property, there are duplicate entries
in /sys/class/power/*/uevent.
So add a check to avoid duplicates. Since all channels may be duplicates,
we have to modify the related error check.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Cc: stable@vger.kernel.org
Fixes: e60fea794e ("power: battery: Generic battery driver using IIO")
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 932d47448c upstream.
We did have sporadic problems in the pinctrl framework during boot
where a pin group name unexpectedly became NULL leading to a NULL
dereference in strcmp.
Detailled analysis of the failing cases did reveal that there were
two devm allocated objects close to each other. The second one was
the affected group_desc in pinmux and the first one was the
psy_desc->properties buffer of the gab driver.
Review of the gab code showed that the address calculation for
one memcpy() is wrong. It does
properties + sizeof(type) * index
but C is defined to do the index multiplication already for
pointer + integer additions. Hence the factor was applied twice
and the memcpy() does write outside of the properties buffer.
Sometimes it happened to be the pinctrl and triggered the strcmp(NULL).
Anyways, it is overkill to use a memcpy() here instead of a simple
assignment, which is easier to read and has less risk for wrong
address calculations. So we change code to a simple assignment.
If we initialize the index to the first free location, we can even
remove the local variable 'properties'.
This bug seems to exist right from the beginning in 3.7-rc1 in
commit e60fea794e ("power: battery: Generic battery driver using IIO")
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Cc: stable@vger.kernel.org
Fixes: e60fea794e ("power: battery: Generic battery driver using IIO")
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 66ec32fc7c ]
max17042_get_status uses the core power_supply_am_i_supplied. That
function relies on DT properties to figure out the power supply
topology, and will error out without DT.
Fixes max17042 battery status being reported as "unknown".
Signed-off-by: Pierre Bourdon <delroth@google.com>
Signed-off-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 165c235774 ]
Properly stop any work we may have queued on probe-errors / remove.
Rather then adding a remove driver callback for this, and goto style
error handling to probe, use a devm_action for this.
The devm_action gets registered before we register any of the extcon
notifiers which may queue the work, devm does cleanup in reverse order,
so this ensures that the notifiers are removed before we cancel the work.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 09edcb6475 ]
If an error occurs when we enable the backup battery charging, we should
go through the error handling path directly.
Before commit db43e6c473 ("ab8500-bm: Add usb power path support") this
was the case, but this commit has added some code between the last test and
the 'out' label.
So, in case of error, this added code is executed and the error may be
silently ignored.
Fix it by adding the missing 'goto out', as done in all other error
handling paths.
Fixes: db43e6c473 ("ab8500-bm: Add usb power path support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bf59fddde1 ]
'ret' is know to be 0 at this point, because it has not been updated by the
the previous call to 'abx500_mask_and_set_register_interruptible()'.
Fix it by updating 'ret' before checking if an error occurred.
Fixes: 84edbeeab6 ("ab8500-charger: AB8500 charger driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 348c7cf5fc upstream.
This change resolves a new compile-time warning
when built as a loadable module:
WARNING: modpost: missing MODULE_LICENSE() in drivers/power/reset/zx-reboot.o
see include/linux/module.h for more information
This adds the license as "GPL v2", which matches the header of the file.
MODULE_DESCRIPTION and MODULE_AUTHOR are also added.
Signed-off-by: Jesse Chan <jc@linux.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MIPS will soon not be a part of Imagination Technologies, and as such
many @imgtec.com email addresses will no longer be valid. This patch
updates the addresses for those who:
- Have 10 or more patches in mainline authored using an @imgtec.com
email address, or any patches dated within the past year.
- Are still with Imagination but leaving as part of the MIPS business
unit, as determined from an internal email address list.
- Haven't already updated their email address (ie. JamesH) or expressed
a desire to be excluded (ie. Maciej).
- Acked v2 or earlier of this patch, which leaves Deng-Cheng, Matt &
myself.
New addresses are of the form firstname.lastname@mips.com, and all
verified against an internal email address list. An entry is added to
.mailmap for each person such that get_maintainer.pl will report the new
addresses rather than @imgtec.com addresses which will soon be dead.
Instances of the affected addresses throughout the tree are then
mechanically replaced with the new @mips.com address.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Cc: Deng-Cheng Zhu <dengcheng.zhu@mips.com>
Acked-by: Dengcheng Zhu <dengcheng.zhu@mips.com>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Matt Redfearn <matt.redfearn@mips.com>
Acked-by: Matt Redfearn <matt.redfearn@mips.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: trivial@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- RK805 Power Management IC (PMIC)
- ROHM BD9571MWV-M MFD Power Management IC (PMIC)
- Texas Instruments TPS68470 Power Management IC (PMIC) & LEDs
- New Device Support
- Add support for HiSilicon Hi6421v530 to hi6421-pmic-core
- Add support for X-Powers AXP806 to axp20x
- Add support for X-Powers AXP813 to axp20x
- Add support for Intel Sunrise Point LPSS to intel-lpss-pci
- New Functionality
- Amend API to provide register layout; atmel-smc
- Fix-ups
- DT re-work; omap, nokia
- Header file location change {I2C => MFD}; dm355evm_msp, tps65010
- Fix chip ID formatting issue(s); rk808
- Optionally register touchscreen devices; da9052-core
- Documentation improvements; twl-core
- Constification; rtsx_pcr, ab8500-core, da9055-i2c, da9052-spi
- Drop unnecessary static declaration; max8925-i2c
- Kconfig changes (missing deps and remove module support)
- Slim down oversized licence statement; hi6421-pmic-core
- Use managed resources (devm_*); lp87565
- Supply proper error checking/handling; t7l66xb
- Bug Fixes
- Fix counter duplication issue; da9052-core
- Fix potential NULL deference issue; max8998
- Leave SPI-NOR write-protection bit alone; lpc_ich
- Ensure device is put into reset during suspend; intel-lpss
- Correct register offset variable size; omap-usb-tll
-----BEGIN PGP SIGNATURE-----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=TKIm
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers
- RK805 Power Management IC (PMIC)
- ROHM BD9571MWV-M MFD Power Management IC (PMIC)
- Texas Instruments TPS68470 Power Management IC (PMIC) & LEDs
New Device Support:
- Add support for HiSilicon Hi6421v530 to hi6421-pmic-core
- Add support for X-Powers AXP806 to axp20x
- Add support for X-Powers AXP813 to axp20x
- Add support for Intel Sunrise Point LPSS to intel-lpss-pci
New Functionality:
- Amend API to provide register layout; atmel-smc
Fix-ups:
- DT re-work; omap, nokia
- Header file location change {I2C => MFD}; dm355evm_msp, tps65010
- Fix chip ID formatting issue(s); rk808
- Optionally register touchscreen devices; da9052-core
- Documentation improvements; twl-core
- Constification; rtsx_pcr, ab8500-core, da9055-i2c, da9052-spi
- Drop unnecessary static declaration; max8925-i2c
- Kconfig changes (missing deps and remove module support)
- Slim down oversized licence statement; hi6421-pmic-core
- Use managed resources (devm_*); lp87565
- Supply proper error checking/handling; t7l66xb
Bug Fixes:
- Fix counter duplication issue; da9052-core
- Fix potential NULL deference issue; max8998
- Leave SPI-NOR write-protection bit alone; lpc_ich
- Ensure device is put into reset during suspend; intel-lpss
- Correct register offset variable size; omap-usb-tll"
* tag 'mfd-next-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (61 commits)
mfd: intel_soc_pmic: Differentiate between Bay and Cherry Trail CRC variants
mfd: intel_soc_pmic: Export separate mfd-cell configs for BYT and CHT
dt-bindings: mfd: Add bindings for ZII RAVE devices
mfd: omap-usb-tll: Fix register offsets
mfd: da9052: Constify spi_device_id
mfd: intel-lpss: Put I2C and SPI controllers into reset state on suspend
mfd: da9055: Constify i2c_device_id
mfd: intel-lpss: Add missing PCI ID for Intel Sunrise Point LPSS devices
mfd: t7l66xb: Handle return value of clk_prepare_enable
mfd: Add ROHM BD9571MWV-M PMIC DT bindings
mfd: intel_soc_pmic_chtwc: Turn Kconfig option into a bool
mfd: lp87565: Convert to use devm_mfd_add_devices()
mfd: Add support for TPS68470 device
mfd: lpc_ich: Do not touch SPI-NOR write protection bit on Haswell/Broadwell
mfd: syscon: atmel-smc: Add helper to retrieve register layout
mfd: axp20x: Use correct platform device ID for many PEK
dt-bindings: mfd: axp20x: Introduce bindings for AXP813
mfd: axp20x: Add support for AXP813 PMIC
dt-bindings: mfd: axp20x: Add AXP806 to supported list of chips
mfd: Add ROHM BD9571MWV-M MFD PMIC driver
...
- Drop the P-state selection algorithm based on a PID controller
from intel_pstate and make it use the same P-state selection
method (based on the CPU load) for all types of systems in the
active mode (Rafael Wysocki, Srinivas Pandruvada).
- Rework the cpufreq core and governors to make it possible to
take cross-CPU utilization updates into account and modify the
schedutil governor to actually do so (Viresh Kumar).
- Clean up the handling of transition latency information in the
cpufreq core and untangle it from the information on which drivers
cannot do dynamic frequency switching (Viresh Kumar).
- Add support for new SoCs (MT2701/MT7623 and MT7622) to the
mediatek cpufreq driver and update its DT bindings (Sean Wang).
- Modify the cpufreq dt-platdev driver to autimatically create
cpufreq devices for the new (v2) Operating Performance Points
(OPP) DT bindings and update its whitelist of supported systems
(Viresh Kumar, Shubhrajyoti Datta, Marc Gonzalez, Khiem Nguyen,
Finley Xiao).
- Add support for Ux500 to the cpufreq-dt driver and drop the
obsolete dbx500 cpufreq driver (Linus Walleij, Arnd Bergmann).
- Add new SoC (R8A7795) support to the cpufreq rcar driver (Khiem
Nguyen).
- Fix and clean up assorted issues in the cpufreq drivers and core
(Arvind Yadav, Christophe Jaillet, Colin Ian King, Gustavo Silva,
Julia Lawall, Leonard Crestez, Rob Herring, Sudeep Holla).
- Update the IO-wait boost handling in the schedutil governor to
make it less aggressive (Joel Fernandes).
- Rework system suspend diagnostics to make it print fewer messages
to the kernel log by default, add a sysfs knob to allow more
suspend-related messages to be printed and add Low Power S0 Idle
constraints checks to the ACPI suspend-to-idle code (Rafael
Wysocki, Srinivas Pandruvada).
- Prefer suspend-to-idle over S3 on ACPI-based systems with the
ACPI_FADT_LOW_POWER_S0 flag set and the Low Power Idle S0 _DSM
interface present in the ACPI tables (Rafael Wysocki).
- Update documentation related to system sleep and rename a number
of items in the code to make it cleare that they are related to
suspend-to-idle (Rafael Wysocki).
- Export a variable allowing device drivers to check the target
system sleep state from the core system suspend code (Florian
Fainelli).
- Clean up the cpuidle subsystem to handle the polling state on
x86 in a more straightforward way and to use %pOF instead of
full_name (Rafael Wysocki, Rob Herring).
- Update the devfreq framework to fix and clean up a few minor
issues (Chanwoo Choi, Rob Herring).
- Extend diagnostics in the generic power domains (genpd) framework
and clean it up slightly (Thara Gopinath, Rob Herring).
- Fix and clean up a couple of issues in the operating performance
points (OPP) framework (Viresh Kumar, Waldemar Rymarkiewicz).
- Add support for RV1108 to the rockchip-io Adaptive Voltage Scaling
(AVS) driver (David Wu).
- Fix the usage of notifiers in CPU power management on some
platforms (Alex Shi).
- Update the pm-graph system suspend/hibernation and boot profiling
utility (Todd Brandt).
- Make it possible to run the cpupower utility without CPU0 (Prarit
Bhargava).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABCAAGBQJZrcDJAAoJEILEb/54YlRx9FUQAIUKvWBAARc61ZIZXjbqZF1v
aEMOBuksFns0CMekdptSic6n4wc81E/XYMS8yDhOOMpyDzfAZsTWjmu+gKwN7w3l
E/yf/NVlhob9JZ7MqGgqD4EUFfFIaKBXPlWFdDi2rdCUXE2L8xJ7rla8i7zyZlc5
pYHfAppBbF4qUcEY4OoOVOOGRZCfMdiLXj0iZOhMX8Y6yLBRk/AjnVADYsF33hoj
gBEfomU+H0K5V8nQEp0ZFKDArPwL+oElHQj6i+nxBpGfPM5evvLXhHOyR6AsldJ5
J4YI1kMuQNSCmvHMqOTxTYyJf8Jcf3Fj4wcjwaVMVGceY1lz6McAKknnFnCqCvz+
mskn84gFCBCM8EoJDqRf0b9MQHcuRyQKM+yw4tjnR9r8yd32erb85ZWFHcPWYhCT
fZatNOwFFv2MU+2vo5J3yeUNSWIKT+uBjy+tKPbrDkUwpKZVRj3Oj+hP3Mq9NE8U
YBqltsj7tmrdA634zI8C7jfS6wF221S0fId/iPszwmPJaVn/lq8Ror7pWL5YI8U7
SCJFjiqDiGmAcQEkuWwFAQnscZkyHpO+Y3A+jfXl/izoaZETaI5+ceIHBaocm3+5
XrOOpHS3ik8EHf9ji0KFCKZ/pYDwllday3cBQPWo3sMIzpQ2lrjbqdnE1cVnBrld
OtHZAeD/jLUXuY6XW2jN
=mAiV
-----END PGP SIGNATURE-----
Merge tag 'pm-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"This time (again) cpufreq gets the majority of changes which mostly
are driver updates (including a major consolidation of intel_pstate),
some schedutil governor modifications and core cleanups.
There also are some changes in the system suspend area, mostly related
to diagnostics and debug messages plus some renames of things related
to suspend-to-idle. One major change here is that suspend-to-idle is
now going to be preferred over S3 on systems where the ACPI tables
indicate to do so and provide requsite support (the Low Power Idle S0
_DSM in particular). The system sleep documentation and the tools
related to it are updated too.
The rest is a few cpuidle changes (nothing major), devfreq updates,
generic power domains (genpd) framework updates and a few assorted
modifications elsewhere.
Specifics:
- Drop the P-state selection algorithm based on a PID controller from
intel_pstate and make it use the same P-state selection method
(based on the CPU load) for all types of systems in the active mode
(Rafael Wysocki, Srinivas Pandruvada).
- Rework the cpufreq core and governors to make it possible to take
cross-CPU utilization updates into account and modify the schedutil
governor to actually do so (Viresh Kumar).
- Clean up the handling of transition latency information in the
cpufreq core and untangle it from the information on which drivers
cannot do dynamic frequency switching (Viresh Kumar).
- Add support for new SoCs (MT2701/MT7623 and MT7622) to the mediatek
cpufreq driver and update its DT bindings (Sean Wang).
- Modify the cpufreq dt-platdev driver to autimatically create
cpufreq devices for the new (v2) Operating Performance Points (OPP)
DT bindings and update its whitelist of supported systems (Viresh
Kumar, Shubhrajyoti Datta, Marc Gonzalez, Khiem Nguyen, Finley
Xiao).
- Add support for Ux500 to the cpufreq-dt driver and drop the
obsolete dbx500 cpufreq driver (Linus Walleij, Arnd Bergmann).
- Add new SoC (R8A7795) support to the cpufreq rcar driver (Khiem
Nguyen).
- Fix and clean up assorted issues in the cpufreq drivers and core
(Arvind Yadav, Christophe Jaillet, Colin Ian King, Gustavo Silva,
Julia Lawall, Leonard Crestez, Rob Herring, Sudeep Holla).
- Update the IO-wait boost handling in the schedutil governor to make
it less aggressive (Joel Fernandes).
- Rework system suspend diagnostics to make it print fewer messages
to the kernel log by default, add a sysfs knob to allow more
suspend-related messages to be printed and add Low Power S0 Idle
constraints checks to the ACPI suspend-to-idle code (Rafael
Wysocki, Srinivas Pandruvada).
- Prefer suspend-to-idle over S3 on ACPI-based systems with the
ACPI_FADT_LOW_POWER_S0 flag set and the Low Power Idle S0 _DSM
interface present in the ACPI tables (Rafael Wysocki).
- Update documentation related to system sleep and rename a number of
items in the code to make it cleare that they are related to
suspend-to-idle (Rafael Wysocki).
- Export a variable allowing device drivers to check the target
system sleep state from the core system suspend code (Florian
Fainelli).
- Clean up the cpuidle subsystem to handle the polling state on x86
in a more straightforward way and to use %pOF instead of full_name
(Rafael Wysocki, Rob Herring).
- Update the devfreq framework to fix and clean up a few minor issues
(Chanwoo Choi, Rob Herring).
- Extend diagnostics in the generic power domains (genpd) framework
and clean it up slightly (Thara Gopinath, Rob Herring).
- Fix and clean up a couple of issues in the operating performance
points (OPP) framework (Viresh Kumar, Waldemar Rymarkiewicz).
- Add support for RV1108 to the rockchip-io Adaptive Voltage Scaling
(AVS) driver (David Wu).
- Fix the usage of notifiers in CPU power management on some
platforms (Alex Shi).
- Update the pm-graph system suspend/hibernation and boot profiling
utility (Todd Brandt).
- Make it possible to run the cpupower utility without CPU0 (Prarit
Bhargava)"
* tag 'pm-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (87 commits)
cpuidle: Make drivers initialize polling state
cpuidle: Move polling state initialization code to separate file
cpuidle: Eliminate the CPUIDLE_DRIVER_STATE_START symbol
cpufreq: imx6q: Fix imx6sx low frequency support
cpufreq: speedstep-lib: make several arrays static, makes code smaller
PM: docs: Delete the obsolete states.txt document
PM: docs: Describe high-level PM strategies and sleep states
PM / devfreq: Fix memory leak when fail to register device
PM / devfreq: Add dependency on PM_OPP
PM / devfreq: Move private devfreq_update_stats() into devfreq
PM / devfreq: Convert to using %pOF instead of full_name
PM / AVS: rockchip-io: add io selectors and supplies for RV1108
cpufreq: ti: Fix 'of_node_put' being called twice in error handling path
cpufreq: dt-platdev: Drop few entries from whitelist
cpufreq: dt-platdev: Automatically create cpufreq device with OPP v2
ARM: ux500: don't select CPUFREQ_DT
cpuidle: Convert to using %pOF instead of full_name
cpufreq: Convert to using %pOF instead of full_name
PM / Domains: Convert to using %pOF instead of full_name
cpufreq: Cap the default transition delay value to 10 ms
...
include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Tested on Pyra prototype with bq27421.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
On some devices the USB Type-C port power (USB PD 2.0) negotiation is
done by a separate port-controller IC, while the current limit is
controlled through another (charger) IC.
It has been decided to model this by modelling the external Type-C
power brick (adapter/charger) as a power-supply class device which
supplies the charger-IC, with its voltage-now and current-max representing
the negotiated voltage and max current draw.
This commit adds support for this to the bq24190_charger driver by adding
an external_power_changed callback and calling
power_supply_set_input_current_limit_from_supplier from this callback.
This callback will only get called if the bq24190 has a parent-supply.
Note this replaces the functionality to get the current-limit from an
extcon device, which will be removed in a follow-up commit.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Register the 5V boost converter as a regulator named "usb_otg_vbus".
This commit also adds support for bq24190_platform_data, through which
non device-tree platforms can pass the regulator_init_data (containing
mappings for the consumer amongst other things).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Set pre-charge and charge-term current, obtained from power_supply_battery_info.
Add sysfs attributes precharge_current & charge_term_current.
Cc: Hans de Goede <hdegoede@redhat.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Set minimum system voltage limit obtained from device property.
Cc: Hans de Goede <hdegoede@redhat.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Add get_config(). Rename set_mode_host() to set_config().
Call get_config() and hw_init() after power_supply_register().
No functional changes.
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Support data memory update on BQ27425. Parameters from TI datasheets are also
provided for BQ27500, 545, 421, 441, 621; however these are commented out,
as they are not tested.
Add BQ27XXX_O_CFGUP & _O_RAM for use in bq27xxx_chip_data[n].opts
and by data memory update functions.
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
For the existing features, these chips act like others already ID'd,
so they had false but functional IDs. We will be adding features
which require correct IDs, so the following IDs are added:
BQ2752X, 531, 542, 546, 742, 425, 441, 621
Chip-specific features are now tracked by BQ27XXX_O_* flags in di->opts.
No functional changes to the driver.
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
To support new features which require different data for each chip, we
unify the bq27xxx_regs and bq27xxx_battery_props tables into a single one.
No functional changes to the driver.
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
bq24192i was previously only in ID table, so add it to DT table.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Export the input current limit of the charger as a
POWER_SUPPLY_PROP_INPUT_CURRENT_LIMIT property on the charger
power_supply class device.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
On some devices the USB Type-C port power (USB PD 2.0) negotiation is
done by a separate port-controller IC, while the current limit is
controlled through another (charger) IC.
It has been decided to model this by modelling the external Type-C
power brick (adapter/charger) as a power-supply class device which
supplies the charger-IC, with its voltage-now and current-max representing
the negotiated voltage and max current draw.
This commit adds a power_supply_set_input_current_limit_from_supplier
helper function which charger power-supply drivers can call to get
the max-current from their supplier and have this applied
through their set_property call-back to their input-current-limit.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Fix drivers/power/supply/max17042_battery.c:1059:6:
warning: 'acpi_id' may be used uninitialized in this function.
No idea why my gcc version did not catch this.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Omit extra messages for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Make these const as they are only passed as an argument to the
function device_create_file and device_remove_file and the corresponding
arguments are of type const.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
On some x86/ACPI boards the DSDT defines an ACPI event handler for
the max17047 IRQ, this causes several problems:
1) We need to share the IRQ to avoid an error getting it
2) Even of we are willing to share, we may fail to share because some
DSDTs claim it exclusivly
3) If we are unable to share the IRQ, or the IRQ is only listed as an
ACPI event source and not in the max1704 firmware node, then the
charge threshold IRQ (which is used to give an IRQ every 1 percent
charge change) becomes a problem, the ACPI event handler will not
update this to the next 1 percent threshold, so the IRQ keeps firing
and we get an IRQ storm pegging 1 CPU core.
This happens despite the max17042 driver not setting the charge
threshold because Windows uses it and leaves it set on reboot.
So if we are unable to get the IRQ we need to reprogram the
charge threshold to its disabled setting.
This commit fixes al of the above, while at it it also makes the error
msg when being unable to get the IRQ consistent with other messages.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Some x86 devices enumerate a max17047 fuel-gauge through a MAX17047
ACPI firmware-node, add support for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
This adds the necessary data for handling io voltage domains on the RV1108.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Integrate with the newly added USB charger interface to limit the current
we draw from the USB input based on the input device configuration
identified by the USB stack, allowing us to charge more quickly from high
current inputs without drawing more current than specified from others.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Don't populate various read only arrays on the stack but make them
static const, making the object code smaller and saves 148 bytes
overall:
Before:
text data bss dec hex filename
11940 4496 64 16500 4074 lp8788-charger.o
After:
text data bss dec hex filename
11472 4816 64 16352 3fe0 lp8788-charger.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Use 'sizeof(*var)' instead of the equivalent 'sizeof(data structure type)'
because it is less verbose.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Update a comment which is no more up to date since commit
2ed9e9b653.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
'devm_kzalloc()' can return NULL. Return -ENOMEM in this case in order to
avoid a NULL pointer dereference later on.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Commit 2848e039c5 ("power: supply: Make power_supply_am_i_supplied return
-ENODEV if there are no suppliers") was supposed to make
power_supply_am_i_supplied() return -ENODEV when there are no supplies
which supply the supply passed to it.
But instead it will only return -ENODEV when there are no supplies at
all as data->count++; is incremented on every call of the iterator, rather
then only when __power_supply_is_supplied_by returns true. This commit
fixes this.
Fixes: 2848e039c5 ("power: supply: Make power_supply_am_i_supplied ...")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Add const to bin_attribute structures as they are only passed to the
functions sysfs_{remove/create}_bin_file or
device_{remove/create}_bin_file. The corresponding parameters
passed are of type const, so declare the structures to be const.
Done using Coccinelle:
@m disable optional_qualifier@
identifier s;
position p;
@@
static struct bin_attribute s@p={...};
@okay1@
position p;
identifier m.s;
@@
(
sysfs_create_bin_file(...,&s@p,...)
|
sysfs_remove_bin_file(...,&s@p,...)
)
@bad@
position p!={m.p,okay1.p};
identifier m.s;
@@
s@p
@change depends on !bad disable optional_qualifier@
identifier m.s;
@@
static
+const
struct bin_attribute s={...};
Same script was modified for device_{create/remove}_bin_file functions.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
When the BQ27xxx driver was originally written the w1 subsystem only
allowed device drivers for w1 attached devices to live in the w1
subsystem. Kernel driver subsystems expect that the driver for a device
live in the directory of the subsystem for which it implements
functionality, not in the directory of the bus that it is attached. To
work around this, the BQ27xxx driver was implemented as a platform device
driver and the interface driver would instantiate this device from within
the w1 directory, then pass a w1 read callback as platform data.
As we can now have the w1 interface driver in the power/supply directory
(like we do already with the i2c interface driver) we can remove this
middle-layer platform driver.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The HDQ interface driver should be in this folder just like the I2C
interface driver. Move this driver out of drivers/w1/slave and into
drivers/power/supply.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
LTC2944 is compatible with LTC2943, but uses different
voltage and current computing constants.
Signed-off-by: Dragos Bogdan <dragos.bogdan@analog.com>
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Tested-by: Dragos Bogdan <dragos.bogdan@analog.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
LTC2942 is pin compatible with LTC2941 providing additional
informations about battery voltage and temperature. It can
be runtime detected using bit A7 in the Status register.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Dragos Bogdan <dragos.bogdan@analog.com>
Tested-by: Dragos Bogdan <dragos.bogdan@analog.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
In order to support LTC2942 which has temperature registers
at different offsets than LTC2943 use following register naming
scheme (prefixes):
- LTC294X_ common registers
- LTC2942_ chips specific registers
- LTC2943_ specific registers
LTC2944 is compatible with LTC2943 but uses different constants
to compute voltage and current, so replace num_regs misused
for device indentification with real device id to discriminate
between those two.
There are no functional changes.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Dragos Bogdan <dragos.bogdan@analog.com>
Tested-by: Dragos Bogdan <dragos.bogdan@analog.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
At least with the Inspired Energy compatible batteries a delay is required
after setting the capacity mode bit from amp to watts or the reverse.
Setting the bit and then immediately pooling the status register results
in an unknown error being returned in the register. Add the delay results
in and ok status being return. This was also seen when reading the charge
and energy registers where the wrong value was returned for the requested
mode.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Tested-by: Michael Heinemann <committed@heine.so>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Sort the header includes prior to adding to the list.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
checkpatch issued an error in having the FSF address in the comment.
As address may change and Linux already includes a copy.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The MAX17211 monitor a single cell pack. The MAX17215 monitor and
balance a 2S or 3S pack or monitor a multiple-series cell pack.
Both device use 1-Wire interfce.
Signed-off-by: Alex A. Mihaylov <minimumlaw@rambler.ru>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
attribute_groups are not supposed to change at runtime. All functions
working with attribute_groups provided by <linux/sysfs.h> work
with const attribute_group. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
2673 400 0 3073 c01 power/supply/pcf50633-charger.o
File size After adding 'const':
text data bss dec hex filename
2737 336 0 3073 bed power/supply/pcf50633-charger.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: linux-pm@vger.kernel.org
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
of_irq_get() may return any negative error number as well as 0 on failure,
while the driver only checks for -EPROBE_DEFER, blithely continuing with
the call to devm_request_irq() -- that function expects *unsigned int*,
so would probably fail anyway when a large IRQ number resulting from a
conversion of a negative error number is passed to it... This, however,
is incorrect behavior -- error number is not IRQ number.
Check for 'irq <= 0' instead and return -ENXIO from probe if of_irq_get()
returned 0.
Fixes: a09209acd6 ("power: supply: act8945a_charger: Add status change update support")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
When CONFIG_OMAP_USB2 is set to 'm' and the charger driver is built-in,
we get this link failure:
drivers/power/supply/cpcap-charger.o: In function `cpcap_charger_probe':
cpcap-charger.c:(.text+0x48c): undefined reference to `omap_usb2_set_comparator'
drivers/power/supply/cpcap-charger.o: In function `cpcap_charger_remove':
cpcap-charger.c:(.text+0x774): undefined reference to `omap_usb2_set_comparator'
This adds a dependency to prevent that problem, while still allowing
compile-testing with the OMAP_USB2 driver completely disabled.
Fixes: 0c9888e3c1 ("power: supply: cpcap-charger: Add minimal CPCAP PMIC battery charger")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The capacity mode bit is bit 15. Currently it is written as
default initialized enum and never shifted. This leads to
a behaviour where the BATTERY_MODE is not correctly
recognized and set again.
This commit initializes the enum accordingly.
Signed-off-by: Michael Heinemann <committed@heine.so>
Tested-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
* two fixes for twl4030-charger
-----BEGIN PGP SIGNATURE-----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=shuZ
-----END PGP SIGNATURE-----
Merge tag 'for-v4.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply fixes from Reichel:
"I have two more fixes for the power-supply subsystem:
- two fixes for twl4030-charger"
* tag 'for-v4.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply:
power: supply: twl4030-charger: add deferred probing for phy and iio
power: supply: twl4030-charger: move irq allocation to just before irqs are enabled
* New drivers
- Linear ltc3651 charger driver
- Motorola CPCAP battery fuel-gauge driver
* New chip/feature support
- bq27xxx: prepare for chip data setup
- axp20x_battery: support max charge current setup
* New core features
- add Apple Brick ID type
- support "supplied-from" device property for generic ACPI/pdata support
- support strings for sysfs properties representing enums
- introduce battery-info (backend is DT only for now)
- provide reboot-mode header globally
* Misc. fixes
-----BEGIN PGP SIGNATURE-----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=SsiM
-----END PGP SIGNATURE-----
Merge tag 'for-v4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset updates from Sebastian Reichel:
"New drivers:
- Linear ltc3651 charger driver
- Motorola CPCAP battery fuel-gauge driver
New chip/feature support:
- bq27xxx: prepare for chip data setup
- axp20x_battery: support max charge current setup
New core features:
- add Apple Brick ID type
- support "supplied-from" device property for generic ACPI/pdata support
- support strings for sysfs properties representing enums
- introduce battery-info (backend is DT only for now)
- provide reboot-mode header globally
.. and misc fixes"
* tag 'for-v4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (39 commits)
power: supply: sbs-battery: Don't needlessly set CAPACITY_MODE
power: supply: sbs-battery: Prevent CAPACITY_MODE races
power: supply: bq24735: remove incorrect le16_to_cpu calls
power: supply: sbs-battery: remove incorrect le16_to_cpu calls
power: supply: cpcap-charger: Add missing power_supply_config
power: supply: twl4030-charger: move allocation of iio channel to the beginning
power: supply: twl4030-charger: allocate iio by devm_iio_channel_get() and fix error path
power: supply: core: constify psy_tcd_ops.
dt-bindings: power: supply: cpcap-battery: Add power-supplies property
dt-bindings: power: supply: move max8903-charger.txt to proper location
dt-bindings: power: supply: move maxim,max14656.txt to proper location
power: supply: twl4030_charger: Use sysfs_match_string() helper
power: reset: reboot-mode: Make include file global
power: supply: axp20x_battery: add DT support for battery max constant charge current
power: supply: axp20x_battery: add support for DT battery
power: supply: bq27xxx: Add power_supply_battery_info support
power: supply: bq27xxx: Add chip data memory read/write support
power: supply: bq27xxx: Add bulk transfer bus methods
dt-bindings: power: supply: bq27xxx: Add monitored-battery documentation
power: supply: core: Add power_supply_prop_precharge
...
- Rework suspend-to-idle to allow it to take wakeup events signaled
by the EC into account on ACPI-based platforms in order to properly
support power button wakeup from suspend-to-idle on recent Dell
laptops (Rafael Wysocki).
That includes the core suspend-to-idle code rework, support for
the Low Power S0 _DSM interface, and support for the ACPI INT0002
Virtual GPIO device from Hans de Goede (required for USB keyboard
wakeup from suspend-to-idle to work on some machines).
- Stop trying to export the current CPU frequency via /proc/cpuinfo
on x86 as that is inaccurate and confusing (Len Brown).
- Rework the way in which the current CPU frequency is exported by
the kernel (over the cpufreq sysfs interface) on x86 systems with
the APERF and MPERF registers by always using values read from
these registers, when available, to compute the current frequency
regardless of which cpufreq driver is in use (Len Brown).
- Rework the PCI/ACPI device wakeup infrastructure to remove the
questionable and artificial distinction between "devices that
can wake up the system from sleep states" and "devices that can
generate wakeup signals in the working state" from it, which
allows the code to be simplified quite a bit (Rafael Wysocki).
- Fix the wakeup IRQ framework by making it use SRCU instead of
RCU which doesn't allow sleeping in the read-side critical
sections, but which in turn is expected to be allowed by the
IRQ bus locking infrastructure (Thomas Gleixner).
- Modify some computations in the intel_pstate driver to avoid
rounding errors resulting from them (Srinivas Pandruvada).
- Reduce the overhead of the intel_pstate driver in the HWP
(hardware-managed P-states) mode and when the "performance"
P-state selection algorithm is in use by making it avoid
registering scheduler callbacks in those cases (Len Brown).
- Rework the energy_performance_preference sysfs knob in
intel_pstate by changing the values that correspond to
different symbolic hint names used by it (Len Brown).
- Make it possible to use more than one cpuidle driver at the same
time on ARM (Daniel Lezcano).
- Make it possible to prevent the cpuidle menu governor from using
the 0 state by disabling it via sysfs (Nicholas Piggin).
- Add support for FFH (Fixed Functional Hardware) MWAIT in ACPI C1
on AMD systems (Yazen Ghannam).
- Make the CPPC cpufreq driver take the lowest nonlinear performance
information into account (Prashanth Prakash).
- Add support for hi3660 to the cpufreq-dt driver, fix the
imx6q driver and clean up the sfi, exynos5440 and intel_pstate
drivers (Colin Ian King, Krzysztof Kozlowski, Octavian Purdila,
Rafael Wysocki, Tao Wang).
- Fix a few minor issues in the generic power domains (genpd)
framework and clean it up somewhat (Krzysztof Kozlowski,
Mikko Perttunen, Viresh Kumar).
- Fix a couple of minor issues in the operating performance points
(OPP) framework and clean it up somewhat (Viresh Kumar).
- Fix a CONFIG dependency in the hibernation core and clean it up
slightly (Balbir Singh, Arvind Yadav, BaoJun Luo).
- Add rk3228 support to the rockchip-io adaptive voltage scaling
(AVS) driver (David Wu).
- Fix an incorrect bit shift operation in the RAPL power capping
driver (Adam Lessnau).
- Add support for the EPP field in the HWP (hardware managed
P-states) control register, HWP.EPP, to the x86_energy_perf_policy
tool and update msr-index.h with HWP.EPP values (Len Brown).
- Fix some minor issues in the turbostat tool (Len Brown).
- Add support for AMD family 0x17 CPUs to the cpupower tool and fix
a minor issue in it (Sherry Hurwitz).
- Assorted cleanups, mostly related to the constification of some
data structures (Arvind Yadav, Joe Perches, Kees Cook, Krzysztof
Kozlowski).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Wsph
-----END PGP SIGNATURE-----
Merge tag 'pm-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"The big ticket items here are the rework of suspend-to-idle in order
to add proper support for power button wakeup from it on recent Dell
laptops and the rework of interfaces exporting the current CPU
frequency on x86.
In addition to that, support for a few new pieces of hardware is
added, the PCI/ACPI device wakeup infrastructure is simplified
significantly and the wakeup IRQ framework is fixed to unbreak the IRQ
bus locking infrastructure.
Also, there are some functional improvements for intel_pstate, tools
updates and small fixes and cleanups all over.
Specifics:
- Rework suspend-to-idle to allow it to take wakeup events signaled
by the EC into account on ACPI-based platforms in order to properly
support power button wakeup from suspend-to-idle on recent Dell
laptops (Rafael Wysocki).
That includes the core suspend-to-idle code rework, support for the
Low Power S0 _DSM interface, and support for the ACPI INT0002
Virtual GPIO device from Hans de Goede (required for USB keyboard
wakeup from suspend-to-idle to work on some machines).
- Stop trying to export the current CPU frequency via /proc/cpuinfo
on x86 as that is inaccurate and confusing (Len Brown).
- Rework the way in which the current CPU frequency is exported by
the kernel (over the cpufreq sysfs interface) on x86 systems with
the APERF and MPERF registers by always using values read from
these registers, when available, to compute the current frequency
regardless of which cpufreq driver is in use (Len Brown).
- Rework the PCI/ACPI device wakeup infrastructure to remove the
questionable and artificial distinction between "devices that can
wake up the system from sleep states" and "devices that can
generate wakeup signals in the working state" from it, which allows
the code to be simplified quite a bit (Rafael Wysocki).
- Fix the wakeup IRQ framework by making it use SRCU instead of RCU
which doesn't allow sleeping in the read-side critical sections,
but which in turn is expected to be allowed by the IRQ bus locking
infrastructure (Thomas Gleixner).
- Modify some computations in the intel_pstate driver to avoid
rounding errors resulting from them (Srinivas Pandruvada).
- Reduce the overhead of the intel_pstate driver in the HWP
(hardware-managed P-states) mode and when the "performance" P-state
selection algorithm is in use by making it avoid registering
scheduler callbacks in those cases (Len Brown).
- Rework the energy_performance_preference sysfs knob in intel_pstate
by changing the values that correspond to different symbolic hint
names used by it (Len Brown).
- Make it possible to use more than one cpuidle driver at the same
time on ARM (Daniel Lezcano).
- Make it possible to prevent the cpuidle menu governor from using
the 0 state by disabling it via sysfs (Nicholas Piggin).
- Add support for FFH (Fixed Functional Hardware) MWAIT in ACPI C1 on
AMD systems (Yazen Ghannam).
- Make the CPPC cpufreq driver take the lowest nonlinear performance
information into account (Prashanth Prakash).
- Add support for hi3660 to the cpufreq-dt driver, fix the imx6q
driver and clean up the sfi, exynos5440 and intel_pstate drivers
(Colin Ian King, Krzysztof Kozlowski, Octavian Purdila, Rafael
Wysocki, Tao Wang).
- Fix a few minor issues in the generic power domains (genpd)
framework and clean it up somewhat (Krzysztof Kozlowski, Mikko
Perttunen, Viresh Kumar).
- Fix a couple of minor issues in the operating performance points
(OPP) framework and clean it up somewhat (Viresh Kumar).
- Fix a CONFIG dependency in the hibernation core and clean it up
slightly (Balbir Singh, Arvind Yadav, BaoJun Luo).
- Add rk3228 support to the rockchip-io adaptive voltage scaling
(AVS) driver (David Wu).
- Fix an incorrect bit shift operation in the RAPL power capping
driver (Adam Lessnau).
- Add support for the EPP field in the HWP (hardware managed
P-states) control register, HWP.EPP, to the x86_energy_perf_policy
tool and update msr-index.h with HWP.EPP values (Len Brown).
- Fix some minor issues in the turbostat tool (Len Brown).
- Add support for AMD family 0x17 CPUs to the cpupower tool and fix a
minor issue in it (Sherry Hurwitz).
- Assorted cleanups, mostly related to the constification of some
data structures (Arvind Yadav, Joe Perches, Kees Cook, Krzysztof
Kozlowski)"
* tag 'pm-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (69 commits)
cpufreq: Update scaling_cur_freq documentation
cpufreq: intel_pstate: Clean up after performance governor changes
PM: hibernate: constify attribute_group structures.
cpuidle: menu: allow state 0 to be disabled
intel_idle: Use more common logging style
PM / Domains: Fix missing default_power_down_ok comment
PM / Domains: Fix unsafe iteration over modified list of domains
PM / Domains: Fix unsafe iteration over modified list of domain providers
PM / Domains: Fix unsafe iteration over modified list of device links
PM / Domains: Handle safely genpd_syscore_switch() call on non-genpd device
PM / Domains: Call driver's noirq callbacks
PM / core: Drop run_wake flag from struct dev_pm_info
PCI / PM: Simplify device wakeup settings code
PCI / PM: Drop pme_interrupt flag from struct pci_dev
ACPI / PM: Consolidate device wakeup settings code
ACPI / PM: Drop run_wake from struct acpi_device_wakeup_flags
PM / QoS: constify *_attribute_group.
PM / AVS: rockchip-io: add io selectors and supplies for rk3228
powercap/RAPL: prevent overridding bits outside of the mask
PM / sysfs: Constify attribute groups
...
This fixes an issue if both this twl4030_charger driver and
phy-twl4030-usb are compiled as modules and loaded in random order.
It has been observed on GTA04 and OpenPandora devices that in worst
case the boot process hangs and in best case the AC detection fails
with a warning.
Therefore we add deferred probing checks for the usb_phy and the
iio channel for AC detection.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
And initialize workers and notifiers as soon as possible.
This avoids a potential race if irqs are enabled and triggered too early
before the worker is properly set up.
Suggested-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
This adds the necessary data for handling io voltage domains on the rk3228.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
According to the smart battery spec (1), the CAPACITY_MODE bit does not
influence the value read from RelativeStateOfCharge(), so don't bother
changing CAPACITY_MODE when doing such a read.
(1) - Smart Battery Data Specification, Rev 1.1, Dec. 11, 1998
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
A subset of smart battery commands return charge or energy depending on
the CAPACITY_MODE bit setting of BatteryMode(). In order to
unambiguously read a charge or energy value, it is necessary to ensure
that CAPACITY_MODE is set as desired, and not changed for the duration
of the attribute read.
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
i2c_smbus commands handle the correct byte order for smbus transactions
internally. This will currently result in incorrect operation on big
endian systems.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
i2c_smbus commands handle the correct byte order for smbus transactions
internally. This will currently result in incorrect operation on big
endian systems.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Otherwise cpcap-battery won't probe properly with the power-supplies
property configured but will fail with "Not all required supplies found,
defer probe".
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
This is in prepraration for EPROBE_DEFER handling because it is quite
likely that geting the (madc) iio channel is deferred more often than
later steps.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Suggested-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
File size before:
text data bss dec hex filename
4240 200 80 4520 11a8 drivers/power/supply/power_supply_core.o
File size After adding 'const':
text data bss dec hex filename
4296 136 80 4512 11a0 drivers/power/supply/power_supply_core.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Use sysfs_match_string() helper instead of open coded variant.
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Like other subsystems we should be able to define slave devices outside
of the w1 directory. To do this we move public facing interface
definitions to include/linux/w1.h and rename the internal definition
file to w1_internal.h.
As w1_family.h and w1_int.h contained almost entirely public
driver interface definitions we simply removed these files and
moved the remaining definitions into w1_internal.h.
With this we can now start to move slave devices out of w1/slaves and
into the subsystem based on the function they implement, again like
other drivers.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the reboot-mode.h include file into include/linux to allow drivers
outside drivers/power/reset to implement reboot-mode.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
This adds the ability to set the maximum constant charge current,
supported by the battery, delivered by this battery power supply to the
battery.
The maximum constant charge current set in DT will also set the default
constant charge current supplied by this supply.
The actual user can modify the constant charge current within the range
of 0 to maximum constant charge current via sysfs.
The user can also modify the maximum constant charge current to widen
the range of possible constant charge current. While this seems quite
risky, a message is printed on the console to warn the user this might
damage the battery. The reason for letting the user change the maximum
constant charge current is for letting users change the battery and
thus, let them adjust the maximum constant charge current according to
what the battery can support.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
This adds support in X-Powers AXP20X and AXP22X battery driver for a
fixed battery in DT.
It will take the minimum supported voltage by the battery as defined in
the battery DT node and set the V_OFF register to this value, telling
the system to shut down if the supplied power is below this value.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Previously there was no way to configure these chips in the event that the
defaults didn't match the battery in question.
For chips with RAM data memory (and also those with flash/NVM data memory
if CONFIG_BATTERY_BQ27XXX_DT_UPDATES_NVM is defined and the user has not
set module param dt_monitored_battery_updates_nvm=0) we now call
power_supply_get_battery_info(), check its values, and write battery
properties to chip data memory if there is a dm_regs table for the chip.
Signed-off-by: Matt Ranostay <matt@ranostay.consulting>
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Add these to enable read/write of chip data memory RAM/NVM/flash:
bq27xxx_battery_seal()
bq27xxx_battery_unseal()
bq27xxx_battery_set_cfgupdate()
bq27xxx_battery_soft_reset()
bq27xxx_battery_read_dm_block()
bq27xxx_battery_write_dm_block()
bq27xxx_battery_checksum_dm_block()
Signed-off-by: Matt Ranostay <matt@ranostay.consulting>
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Declare bus.write/read_bulk/write_bulk().
Add I2C write/read_bulk/write_bulk() to implement the above.
Add bq27xxx_write/read_block/write_block() helpers to call the above.
Signed-off-by: Matt Ranostay <matt@ranostay.consulting>
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Acked-by: "Andrew F. Davis" <afd@ti.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
power_supply_get_battery_info() reads battery data from devicetree.
struct power_supply_battery_info provides battery data to drivers.
Its fields correspond to elements in enum power_supply_property.
Drivers may surface battery data in sysfs via corresponding
POWER_SUPPLY_PROP_* fields.
Signed-off-by: Matt Ranostay <matt@ranostay.consulting>
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
On the CPCAP PMIC we can use the ADCs for monitoring the battery,
and there is also a coulomb counter. So let's add basic support for
the battery driver.
I did not add any capacity prediction as that should probably be
done in the user space. Or at least user space should tell the kernel
some battery statistics and then the kernel driver could display the
capacity based on that.
Cc: devicetree@vger.kernel.org
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
On Broadcom MIPS STB platforms, BMIPS_GENERIC is the Kconfig symbol that
is used, make this reboot driver default to that value to make sure we
can reboot a system properly.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Since commit 37eb56dc79 ("arm64: Add Broadcom Set Top Box Kconfig
entry point") we have ARCH_BRCMSTB also visible on ARM64 platform, yet
this reboot driver was not selectable, so fix that.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Assembly in at91_lpddr_poweroff has r0 in the clobber list but uses r6.
Reported-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Assembly in at91_lpddr_poweroff has r0 in the clobber list but uses r6.
Reported-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Since we now support the standard 'input_current_limit' property by
commit 3fb319c2cd ("power: supply: twl4030-charger: add writable INPUT_CURRENT_LIMIT property")
we can now remove the nonstandard 'max_current' sysfs attribute.
See Documentation/power/power_supply_class.txt line 125
Both are functionally equivalent. From ABI point of view it is just a rename
of the property.
This also removes the entry in Documentation/ABI/testing/sysfs-class-power-twl4030
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
There are several cut and past bugs here. ltc3651_charger->charger is
NULL at this point, so we return success instead of the intended error
codes.
Fixes: c94d4ed017 ("power: supply: Add ltc3651-charger driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
[Wei Yongjun found the same issue independently]
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This fixes the TODO to parse strings and convert them to enum values
when writing to a power_supply class property sysfs attribute.
There is at least one driver that has a writable enum property that
previously could only be written as an integer, so a fallback to writing
enums as integers instead of strings is provided so we don't break existing
userspace programs.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Apple currently supports three very common USB chargers:
https://www.apple.com/power-adapters/
These chargers implement a proprietary Apple method for advertising
1A, 2.1A, and 2.4A at 5V called "Brick ID".
In addition, 3rd parties implement the same charging method in many
charging accessories that work with iOS devices.
Devices that have charger detection chips such as the Pericom PI3USB9281,
eg. Google Chromebook Pixel 2015, are capable of detecting
these chargers, so let's add a type to facilicate passing that info
up to userspace.
This adds a separate power supply type for Apple's proprietary
"Brick ID" charging method.
Signed-off-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
On devicetree using platforms the devicetree can provide info on which
power-supplies supply another power-supply through phandles.
This commit adds support for providing this info on non devicetree
platforms through the platform code setting a supplied-from
device-property on the power-supplies parent device.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Drop static on a local variable, when the variable is either first
initialized or never used, on every possible execution path through the
function. The static has no benefit, and dropping it reduces the code
size.
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@bad exists@
position p;
identifier x;
type T;
@@
static T x@p;
...
x = <+...x...+>
@@
identifier x;
expression e;
type T;
position p != bad.p;
@@
-static
T x@p;
... when != x
when strict
?x = e;
// </smpl>
The change in code size is indicates by the following output from the size
command.
before:
text data bss dec hex filename
2865 252 8 3125 c35 drivers/power/supply/axp20x_usb_power.o
after:
text data bss dec hex filename
2822 252 0 3074 c02 drivers/power/supply/axp20x_usb_power.o
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The LTC3651 reports its status via GPIO lines. This driver translates
the GPIO levels to battery charger status information via sysfs.
It relies on devicetree to supply the IO configuration.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
With the ADC driver working, we can now fix the voltage table based on
the values read from the ADC.
Note that unlike the ICHRG registers, the VCHRG register bits don't
match the MC13783UG.pdf.
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Turns out a similar battery charger hardware is documented for NXP MC13783
PMIC in "MC13783 Power Management and Audio Circuit Users's Guide" named
MC13783UG.pdf. Looks like the CPCAP charge current table matches that, so
let's start using the nominal values from it.
While at it, let's also add comments to some of the mystery CPCAP charger
registers based on the MC13783UG.pdf documentation.
Note that this patch does not contain any functional changes, the register
values being used stay the same.
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
* New battery driver for AXP20X and AXP22X PMICs
* Improve max17042_battery for usage on x86
* Misc small cleanups & fixes
-----BEGIN PGP SIGNATURE-----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=lF9I
-----END PGP SIGNATURE-----
Merge tag 'for-v4.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull more power-supply updates from Sebastian Reichel:
"The power-supply subsystem has a few more changes for the v4.12 merge
window:
- New battery driver for AXP20X and AXP22X PMICs
- Improve max17042_battery for usage on x86
- Misc small cleanups & fixes"
* tag 'for-v4.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (34 commits)
power: supply: cpcap-charger: Keep trickle charger bits disabled
power: supply: cpcap-charger: Fix enable for 3.8V charge setting
power: supply: cpcap-charger: Fix charge voltage configuration
power: supply: cpcap-charger: Fix charger name
power: supply: twl4030-charger: make twl4030_bci_property_is_writeable static
power: supply: sbs-battery: Add alert callback
mailmap: add Sebastian Reichel
power: supply: avoid unused twl4030-madc.h
power: supply: sbs-battery: Correct supply status with current draw
power: supply: sbs-battery: Don't ignore the first external power change
power: supply: pda_power: move from timer to delayed_work
power: supply: max17042_battery: Add support for the SCOPE property
power: supply: max17042_battery: Add support for the CHARGE_NOW property
power: supply: max17042_battery: Add support for the CHARGE_FULL_DESIGN property
power: supply: max17042_battery: mAh readings depend on r_sns value
power: supply: max17042_battery: Add support for the VOLT_MIN property
power: supply: max17042_battery: Add support for the TECHNOLOGY attribute
power: supply: max17042_battery: Add external_power_changed callback
power: supply: max17042_battery: Add support for the STATUS property
power: supply: max17042_battery: Add default platform_data fallback data
...
Android does not seem to set the trickle charger bits, and these
seem to be only used by the bootloader when bringing up a
completely discharged battery. So let's keep the trickle charging
bits disabled and avoid misconfiguring the hardware.
Fixes: 0c9888e3c1 ("power: supply: cpcap-charger: Add minimal
CPCAP PMIC battery charger")
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Zero is a valid register value for for 3.8V charging.
Fixes: 0c9888e3c1 ("power: supply: cpcap-charger: Add minimal
CPCAP PMIC battery charger")
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
We have the charge voltage wrong, it should be 4.35V instead of 4.2V.
This will cause the battery to never get fully charged.
I noticed this when looking at the Andoid kernel battery and charger
status for a fully charged battery:
POWER_SUPPLY_VOLTAGE_NOW=4351000
Also the battery on droid 4 says "4.35, 1735/1785mAh (min/typ),
6.6/6.8 Wh (min/typ)". Presumably the 4.35 on the battery is the
charge voltage.
And finally, on Android the CPCAP CRM register is set to 0x03b5 where
the b is the charge voltage.
Let's fix the charge voltage define and update the charge configuration
to use the 4.35V setting.
Fixes: 0c9888e3c1 ("power: supply: cpcap-charger: Add minimal
CPCAP PMIC battery charger")
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
I noticed we have a different name from what Android is using.
Let's not break the /sys/class/power user space interface here
and use the same naming as Android has.
On Android we have the following for droid 4:
$ ls /sys/class/power_supply/
ac battery usb
So let's use the usb naming here for charger too.
Fixes: 0c9888e3c1 ("power: supply: cpcap-charger: Add minimal
CPCAP PMIC battery charger")
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The function twl4030_bci_property_is_writeable can be made static
as it does not need to be in global scope.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: "H. Nikolaus Schaller" <hns@goldelico.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
- Update the core device enumeration code to make it more internally
consistent and robust and drop the force_remove sysfs attribute
that could be used to tell it to ignore errors on device
hot-removal which was dangerous in general and no real and
still relevant use cases for it could be found (Rafael Wysocki,
Michal Hocko).
- Make the core device enumeration code use _PXM to associate
platform devices created by it with specific NUMA nodes (Shanker
Donthineni).
- Extend the CPPC library by adding more sysfs entries for
performance capabilities to it and making it use the lowest
nonlinear performance parameter (Prashanth Prakash).
- Make the CPU online more consistent with CPU initialization in
the ACPI processor driver (Prashanth Prakash).
- Update the AC and battery drivers to help them avoid attaching to
devices that cannot be handled by them and update the axp288_charger
power supply driver to work correctly on ACPI systems without the
INT3496 device (Hans de Goede).
- Add an ACPI operation region driver for the Intel CHT Whiskey Cove
PMIC and update the xpower operation region driver to work without
IIO which isn't really necessary for it to work (Hans de Goede).
- Add a new entry for Dell Inspiron 7537 to the _REV quirk blacklist
(Kai Heng Feng).
- Make the code in the ACPI video driver easier to follow by adding
symbols and comments to it (Dmitry Frank).
- Update ACPI documentation and drop a function that has no users
from the tables-handling code (Cao jin, Baoquan He).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=IwcL
-----END PGP SIGNATURE-----
Merge tag 'acpi-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"These are some device enumeration code changes, updates of the AC and
battery drivers to help them avoid attaching to devices that cannot be
handled by them, new operation region driver for the Intel CHT Whiskey
Cove PMIC, new sysfs entries for CPPC performance capabilities, a new
_REV quirk blacklist entry and a couple of assorted minor fixes and
cleanups.
Specifics:
- Update the core device enumeration code to make it more internally
consistent and robust and drop the force_remove sysfs attribute
that could be used to tell it to ignore errors on device
hot-removal which was dangerous in general and no real and still
relevant use cases for it could be found (Rafael Wysocki, Michal
Hocko).
- Make the core device enumeration code use _PXM to associate
platform devices created by it with specific NUMA nodes (Shanker
Donthineni).
- Extend the CPPC library by adding more sysfs entries for
performance capabilities to it and making it use the lowest
nonlinear performance parameter (Prashanth Prakash).
- Make the CPU online more consistent with CPU initialization in the
ACPI processor driver (Prashanth Prakash).
- Update the AC and battery drivers to help them avoid attaching to
devices that cannot be handled by them and update the
axp288_charger power supply driver to work correctly on ACPI
systems without the INT3496 device (Hans de Goede).
- Add an ACPI operation region driver for the Intel CHT Whiskey Cove
PMIC and update the xpower operation region driver to work without
IIO which isn't really necessary for it to work (Hans de Goede).
- Add a new entry for Dell Inspiron 7537 to the _REV quirk blacklist
(Kai Heng Feng).
- Make the code in the ACPI video driver easier to follow by adding
symbols and comments to it (Dmitry Frank).
- Update ACPI documentation and drop a function that has no users
from the tables-handling code (Cao jin, Baoquan He)"
* tag 'acpi-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / PMIC: Stop xpower OPRegion handler relying on IIO
ACPI / PMIC: Add opregion driver for Intel CHT Whiskey Cove PMIC
ACPI / scan: Avoid enumerating devices more than once
ACPI / scan: Apply default enumeration to devices with ACPI drivers
power: supply: axp288_charger: Only wait for INT3496 device if present
ACPI / AC: Add a blacklist with PMIC ACPI HIDs with a native charger driver
ACPI / battery: Add a blacklist with PMIC ACPI HIDs with a native battery driver
ACPI / battery: Fix acpi_battery_exit on acpi_battery_init_async errors
ACPI / utils: Add new acpi_dev_present helper
ACPI / video: add comments about subtle cases
ACPI / video: get rid of magic numbers and use enum instead
ACPI / doc: linuxized-acpica.txt: fix typos
ACPI / blacklist: add _REV quirk for Dell Inspiron 7537
ACPI / tables: Drop acpi_parse_entries() which is not used
ACPI / CPPC: add sysfs entries for CPPC perf capabilities
ACPI / CPPC: Read lowest nonlinear perf in cppc_get_perf_caps()
ACPI / platform: Update platform device NUMA node based on _PXM method
ACPI / Processor: Drop setup_max_cpus check from acpi_processor_add()
ACPI / scan: Drop support for force_remove
- Rework the intel_pstate driver's sysfs interface to make it
more straightforward and more intuitive (Rafael Wysocki).
- Make intel_pstate support all processors which advertise HWP
(hardware-managed P-states) to the kernel in all operation modes
and make it use the load-based P-state selection algorithm on a
wider range of systems in the active mode (Rafael Wysocki).
- Add cpufreq driver for Tegra186 (Mikko Perttunen).
- Add support for Gemini Lake SoCs to intel_pstate (David Box).
- Add support for MT8176 and MT817x to the Mediatek cpufreq driver
and clean up that driver a bit (Daniel Kurtz).
- Clean up intel_pstate and optimize it slightly (Rafael Wysocki).
- Update the schedutil cpufreq governor, mostly to fix a couple of
issues with it related to specific workloads, and rework its sysfs
tunable and initialization a bit (Rafael Wysocki, Viresh Kumar).
- Fix minor issues in the imx6q, dbx500 and qoriq cpufreq drivers
(Christophe Jaillet, Irina Tirdea, Leonard Crestez, Viresh Kumar,
YuanTian Tang).
- Add file patterns for cpufreq DT bindings to MAINTAINERS (Geert
Uytterhoeven).
- Add support for "always on" power domains to the genpd (generic
power domains) framework and clean up that code somewhat (Ulf
Hansson, Lina Iyer, Viresh Kumar).
- Fix minor issues in the powernv cpuidle driver and clean it up
(Anton Blanchard, Gautham Shenoy).
- Move the AnalyzeSuspend utility under tools/power/pm-graph/ and
add an analogous boot-profiling utility called AnalyzeBoot to it
(Todd Brandt).
- Add rk3328 support to the rockchip-io AVS (Adaptive Voltage
Scaling) driver (David Wu).
- Fix minor issues in the cpuidle core, the intel_pstate_tracer
utility, the devfreq framework and the PM core documentation
(Chanwoo Choi, Doug Smythies, Johan Hovold, Marcin Nowakowski).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=6M3e
-----END PGP SIGNATURE-----
Merge tag 'pm-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"This time the majority of changes go to the cpufreq subsystem (and to
the intel_pstate driver in particular) and there are some updates in
the generic power domains framework, cpuidle, tools and a couple of
other places.
One thing worth mentioning is that the intel_pstate's sysfs interface
has been reworked to be more consistent with the general expectations
of the cpufreq core and less confusing, hopefully for the better.
Also, we have a new cpufreq driver for Tegra186 and new hardware
support in intel_pstata and the Mediatek cpufreq driver.
Apart from that, the AnalyzeSuspend utility for system suspend
profiling gets a companion called AnalyzeBoot for the analogous
profiling of system boot and they both go into one place under
tools/power/pm-graph/.
The rest is mostly fixes, cleanups and code reorganization.
Specifics:
- Rework the intel_pstate driver's sysfs interface to make it more
straightforward and more intuitive (Rafael Wysocki).
- Make intel_pstate support all processors which advertise HWP
(hardware-managed P-states) to the kernel in all operation modes
and make it use the load-based P-state selection algorithm on a
wider range of systems in the active mode (Rafael Wysocki).
- Add cpufreq driver for Tegra186 (Mikko Perttunen).
- Add support for Gemini Lake SoCs to intel_pstate (David Box).
- Add support for MT8176 and MT817x to the Mediatek cpufreq driver
and clean up that driver a bit (Daniel Kurtz).
- Clean up intel_pstate and optimize it slightly (Rafael Wysocki).
- Update the schedutil cpufreq governor, mostly to fix a couple of
issues with it related to specific workloads, and rework its sysfs
tunable and initialization a bit (Rafael Wysocki, Viresh Kumar).
- Fix minor issues in the imx6q, dbx500 and qoriq cpufreq drivers
(Christophe Jaillet, Irina Tirdea, Leonard Crestez, Viresh Kumar,
YuanTian Tang).
- Add file patterns for cpufreq DT bindings to MAINTAINERS (Geert
Uytterhoeven).
- Add support for "always on" power domains to the genpd (generic
power domains) framework and clean up that code somewhat (Ulf
Hansson, Lina Iyer, Viresh Kumar).
- Fix minor issues in the powernv cpuidle driver and clean it up
(Anton Blanchard, Gautham Shenoy).
- Move the AnalyzeSuspend utility under tools/power/pm-graph/ and add
an analogous boot-profiling utility called AnalyzeBoot to it (Todd
Brandt).
- Add rk3328 support to the rockchip-io AVS (Adaptive Voltage
Scaling) driver (David Wu).
- Fix minor issues in the cpuidle core, the intel_pstate_tracer
utility, the devfreq framework and the PM core documentation
(Chanwoo Choi, Doug Smythies, Johan Hovold, Marcin Nowakowski)"
* tag 'pm-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (56 commits)
PM / runtime: Document autosuspend-helper side effects
PM / runtime: Fix autosuspend documentation
tools: power: pm-graph: Package makefile and man pages
tools: power: pm-graph: AnalyzeBoot v2.0
tools: power: pm-graph: AnalyzeSuspend v4.6
cpufreq: Add Tegra186 cpufreq driver
cpufreq: imx6q: Fix error handling code
cpufreq: imx6q: Set max suspend_freq to avoid changes during suspend
cpufreq: imx6q: Fix handling EPROBE_DEFER from regulator
cpuidle: powernv: Avoid a branch in the core snooze_loop() loop
cpuidle: powernv: Don't continually set thread priority in snooze_loop()
cpuidle: powernv: Don't bounce between low and very low thread priority
cpuidle: cpuidle-cps: remove unused variable
tools/power/x86/intel_pstate_tracer: Adjust directory ownership
cpufreq: schedutil: Use policy-dependent transition delays
cpufreq: schedutil: Reduce frequencies slower
PM / devfreq: Move struct devfreq_governor to devfreq directory
PM / Domains: Ignore domain-idle-states that are not compatible
cpufreq: intel_pstate: Add support for Gemini Lake
powernv-cpuidle: Validate DT property array size
...
To simplify the sbs-manager code and notification of battery removal
use the i2c alert callback to notify the sbs-battery driver that an
event has occurred.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Avoid inclusion of unused twl4030-madc.h. This
will allow twl4030-madc.h to be merged into the
iio driver.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The status reported directly by the battery controller is not always
reliable and should be corrected based on the current draw information.
This implements such a correction with a dedicated function, called
where the supply status is retrieved.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
A mechanism to ignore the first external power change notification was
put in place years ago to ignore the power_supply_register notification.
However, this doesn't apply to the current situation anymore, as the
first notification is always the result of a legitimate power change.
This removes this deprecated mechanism, which puts back the driver's
state machine to a sane state (an ignored first notification previously
caused a charging/discharging status inversion).
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Add support for the SCOPE property, always return SCOPE_SYSTEM,
as the max170xx is used for the main battery on all known systems
with a max170xx.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
At least upower prefers the more precise charge_now sysfs value over
capacity and the max17042 has the info, so lets export it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The info is there, lets export it as a property.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The PROP_CHARGE_FULL code was hardcoded for the default sense
resistor of 0.010 Ohm, make it use r_sns which contains the
actual sense resistor value in micro-Ohms instead.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The info is there, so lets export it, like we already do for VOLT_MAX.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The max17042 is intended for Li-Ion or Li-Po batteries, add a TECHNOLOGY
attribute to reflect this. Note this is hardcoded to Li-Ion as there is
no way to tell the difference, and Lithium-Ion Polymer batteries are
a sub-family of Lithium-Ion so Li-Ion technically is correct for both.
Using Li-Ion for both is already done by many drivers and is much
better then not providing any technology info at all.
Suggested-by: Wolfgang Wiedmeyer <wolfgit@wiedmeyer.de>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
If our supplier changes status, chances are we've changed status too,
let any listeners know about this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Userspace prefers the driver having a status property over having to guess
itself. Specifically this will properly make the GNOME3 UI (and likely
others) properly show discharging / charging / full status, instead
of always showing discharging as status.
Note that in the case there is no charger driver supplying the max17042,
then a status of unknown will get returned. At least upower treats
this the same as not having a status attribute, so in this case nothing
changes from a userspace pov.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Some x86 machines use a max17047 fuel-gauge and x86 might be missing
platform_data if not provided by SFI.
This commit adds default platform_data as fallback option so that the
driver can work on boards where no platform_data is provided.
Since not all boards have a thermistor hooked up, set temp_min to 0 and
change the health checks from temp <= temp_min to temp < temp_min to
not trigger on such boards (where temp reads 0).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The temp alert values are 8-bit 2's complement, so sign-extend them
before reporting them back to the caller.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Use sign_extend32 to sign-extend variables where necessary instead of
DIY code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
trivial fix to spelling mistake in dev_error message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
When CONFIG_IIO=m and the axp20x_usb_power driver is built-in, we get
a link time error:
drivers/power/built-in.o: In function `axp20x_usb_power_get_property':
undefined reference to `iio_read_channel_processed'
drivers/power/built-in.o: In function `axp20x_usb_power_probe':
undefined reference to `devm_iio_channel_get'
undefined reference to `devm_iio_channel_get'
This adds the same dependency that we already have for the AC power driver
to the USB power driver. For consistency, I'm also moving the two closer
together in the Kconfig file.
Fixes: 33863c938c ("power: supply: axp20x_usb_power: use IIO channels when available")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Function devm_kzalloc() will return a NULL pointer. However, in function
isp1704_charger_probe(), the return value of devm_kzalloc() is directly
used without validation. This may result in a bad memory access bug.
Fixes: 34a109610e ("isp1704_charger: Add DT support")
Signed-off-by: Pan Bian <bianpan2016@163.com>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Since we use the default primary handler for the irq, IRQF_ONESHOT must
be set. Otherwise the request fails and the following errors are
displayed:
genirq: Threaded irq requested with handler=NULL and !ONESHOT for irq 129
sbs-battery 0-000b: Failed to request irq: -22
Signed-off-by: Ryosuke Saito <raitosyo@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The X-Powers AXP20X and AXP22X PMICs can have a battery as power supply.
This patch adds the battery power supply driver to get various data from
the PMIC, such as the battery status (charging, discharging, full,
dead), current max limit, current current, battery capacity (in
percentage), voltage max and min limits, current voltage and battery
capacity (in Ah).
This battery driver uses the AXP20X/AXP22X ADC driver as PMIC data
provider.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The driver was registering two classes, bq24190-battery & -charger.
Because the power supply framework cannot surface features from multiple
drivers in a single class, a fuel gauge driver would create a third class,
which some power management utilities cannot see.
Deprecate the -battery class for future removal and replicate its features
in -charger. Set /sys/class...-charger/online = pg_stat && !batfet_disable.
If device_property "omit-battery-class" is set, don't register -battery.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
It is sensible to assume that the hardware actually always has a
way of charging the battery so when power_supply_am_i_supplied does not
find any suppliers, that does not mean that there are none, but simply
that no power_supply-drivers are registered / bound for any suppliers for
the supply calling power_supply_am_i_supplied.
At which point a fuel-gauge driver calling power_supply_am_i_supplied()
cannot determine whether the battery is being charged or not.
Allow a caller of power_supply_am_i_supplied to differentiate between
there not being any suppliers, vs no suppliers being online by returning
-ENODEV if there are no suppliers matching supplied_to / supplied_from,
which allows fuel-gauge drivers to return POWER_SUPPLY_STATUS_UNKNOWN
rather then POWER_SUPPLY_STATUS_DISCHARGING if there are no suppliers.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
We can't assume that the battery is or stays present after probing
on devices with replaceable battery.
On some devices (e.g. GTA04 or OpenPanodra) it can be removed
and even be hot swapped by the user while device continues to operate
through external AC or USB power (as long as system power consumption
remains below ca. 500mA as provided by USB). Under certain conditions
it is possible to boot without battery.
So it makes no sense to check for this situation during probe and make
the charger driver (and its status reports) completely non-operational if
the battery can be inserted later.
Tested on: GTA04 and OpenPandora.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Currently, the twl4030 charger defines its own max_current by directly
creating sysfs nodes. It should use the input_current_limit property
which is e.g. used by the bq24257 driver.
This patch adds the input_current_property with the same semantics as
the max_current property. The code to manage the max_current property
is removed by a separate patch.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Allow platform-code to disable the reset on probe and suspend/resume
by setting a "disable-reset" boolean device property on the device.
There are several reasons why the platform-code may want to disable
the reset on probe and suspend/resume:
1) Resetting the charger should never be necessary it should always have
sane values programmed. If it is running with invalid values while we
are not running (system turned off or suspended) there is a big problem
as that may lead to overcharging the battery.
2) The reset in suspend() is meant to put the charger back into default
mode, but this is not necessary and not a good idea. If the charger has
been programmed with a higher max charge_current / charge_voltage then
putting it back in default-mode will reset those to the safe power-on
defaults, leading to slower charging, or charging to a lower voltage
(and thus not using the full capacity) while suspended which is
undesirable. Reprogramming the max charge_current / charge_voltage
after the reset will not help here as that will put the charger back
in host mode and start the i2c watchdog if the host then does not do
anything for 40s (iow if we're suspended for more then 40s) the watchdog
expires resetting the device to default-mode, including resetting all
the registers to there safe power-on defaults. So the only way to keep
using custom charge settings while suspending is to keep the charger in
its normal running state with the i2c watchdog disabled. This is fine
as the charger will still automatically switch from constant current
to constant voltage and stop charging when the battery is full.
3) Besides never being necessary resetting the charger also causes
problems on systems where the charge voltage limit is set higher then the
reset value, if this is the case and the charger is reset while charging
and the battery voltage is between the 2 voltages, then about half the
time the charger gets confused and claims to be charging (REG08 contains
0x64) but in reality the charger has decoupled itself from VBUS (Q1 off)
and is drawing 0A from VBUS, leaving the system running from the battery.
This last problem is happening on a GPD-win mini PC with a bq24292i
charger chip combined with a max17047 fuel-gauge and a LiHV battery.
I've checked and TI does not list any errata for the bq24292i which
could explain this (there are no errata at all).
Cc: Liam Breck <kernel@networkimprov.net>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Liam Breck <kernel@networkimprov.net>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
On some devices with an axp288 pmic setting vbus path based on the
id-pin is handled by an ACPI _AIE interrupt on the gpio and the
INT3496 device is disabled.
Instead of returning -EPROBE_DEFER on these devices waiting for the
never to show up INT3496 device, check for its presence and only
request and monitor the matching extcon if the device is there,
otherwise let the firmware handle the vbus path control.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When I submitted the extcon handling I had a patch pending for the
extcon sub-system for extcon_register_notifier to take -1 as cable id
for listening for all type cable events on an extcon with a single
notifier.
In the end it was decided to instead add a new
extcon_register_notifier_all function for this, switch to using this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Liam Breck <kernel@networkimprov.net>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
On chip reset, polling loop used udelay(10) which is too short
to be useful. Instead, use usleep_range(100, 200).
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
On pm_runtime_get() failure, always emit an error message.
Prevent unbalanced pm_runtime_get by calling:
pm_runtime_put_noidle() in irq handler
pm_runtime_put_sync() on any probe() failure
Rename probe() out labels instead of renumbering them.
Fixes: 13d6fa8447fa ("power: bq24190_charger: Use PM runtime autosuspend")
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Polishing and fixes for initial extcon patch.
Fixes: 4db249b6f3b4 ("power: supply: bq24190_charger: Use extcon to determine ilimit, 5v boost")
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
If the charger is unplugged before the battery is full we may
see an over/under voltage fault. Ignore this rather then emitting
a message or uevent.
This fixes messages like these getting logged on charger unplug + replug:
bq24190-charger 15-006b: Fault: boost 0, charge 1, battery 0, ntc 0
bq24190-charger 15-006b: Fault: boost 0, charge 0, battery 0, ntc 0
Cc: Tony Lindgren <tony@atomide.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This adds a new driver for the LEGO MINDSTORMS EV3 battery. The EV3 is
an embedded ARM device that can use 6 AA batteries or a special rechargeable
Li-ion battery pack. The rechargeable battery pack presses a special key
switch in the battery compartment to indicate that it is present.
The EV3 is only capable of monitoring battery voltage and current. The
charging circuit is built into the rechargeable battery pack and there is
no way to communicate with is, so we can't provide any information about
charging status.
When not using the rechargeable battery pack, it is most common to use
alkaline batteries to power the device, but it is also common for people to
use rechargeable NiMH batteries. Since there is not a way to automatically
differentiate between these, the technology property is made writable.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Equivalent information can be nowadays obtained using function tracer.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Some trivial improvements on the returning value of the
functions:
- remove unnecessary goto labels that just return, return
immediately, instead.
- do not initialize when not needed.
- return the value from the calling function that fails instead
of politically choosing -EINVAL.
Signed-off-by: Andi Shyti <andi@etezian.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
val might become 7 in which case stime[7] (array of length 7) would be
accessed during the scnprintf call later and that will cause issues.
Obviously, string concatenation is not intended here so just a comma needs
to be added to fix the issue.
Fixes: 98a2766493 ("power_supply: Add new lp8788 charger driver")
Signed-off-by: Giedrius Statkevičius <giedrius.statkevicius@gmail.com>
Acked-by: Milo Kim <milo.kim@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The custom CPCAP PMIC used on Motorola phones such as Droid 4 has a
USB battery charger. It can optionally also have a companion chip that
is used for wireless charging.
The charger on CPCAP also can feed VBUS for the USB host mode. This
can be handled by the existing kernel phy_companion interface.
Cc: devicetree@vger.kernel.org
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Add support for monitoring an extcon device with USB SDP/CDP/DCP and HOST
cables and adjust ilimit and enable/disable the 5V boost converter
accordingly. This is necessary on systems where the PSEL pin is hardwired
high and ILIM needs to be set by software based on the detected charger
type, as well as on systems where the 5V boost converter is used, as
that always needs to be enabled from software.
Cc: Liam Breck <kernel@networkimprov.net>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The bq24192 and bq24192i are mostly identical to the bq24190, TI even
published a single datasheet for all 3 of them. The difference
between the bq24190 and bq24192[i] is the way charger-type detection
is done, the bq24190 is to be directly connected to the USB a/b lines,
where as the the bq24192[i] has a gpio which should be driven high/low
externally depending on the type of charger connected, from a register
level access pov there is no difference.
The differences between the bq24192 and bq24192i are:
1) Lower default charge rate on the bq24192i
2) Pre-charge-current can be max 640 mA on the bq24192i
On x86/ACPI systems the code which instantiates the i2c client may not
know the exact variant being used, so instead of coding the model-id
in the i2c_id struct and bailing if it does not match, check the reported
model-id matches one of the supported variants.
This commit only adds support for the bq24192i as I don't
have a bq24192 to test with, adding support for the bq24192 should
be as simple as also accepting its model-id in the model-id test.
Cc: Liam Breck <kernel@networkimprov.net>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The i2c-core already maps of irqs before calling the driver's probe
function and there are no in tree users of
bq24190_platform_data->gpio_int.
Remove the redundant custom irq-mapping code and just use client->irq.
Cc: Liam Breck <kernel@networkimprov.net>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Robin Gong