This node pointer is returned by of_get_child_by_name() with
refcount incremented in this function. of_node_put() is missing
when exitting this function while invalid device type. Fix it
by move of_get_child_by_name() code after device type check.
Found by Coccinelle.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mark Brown <broonie@kernel.org>
This can be used to expose the act8600 registers via debugfs.
Signed-off-by: Maarten ter Huurne <maarten@treewalker.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This makes the code easier to read and it avoids a dynamic memory
allocation.
Signed-off-by: Maarten ter Huurne <maarten@treewalker.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The check would dereference pdata, which can be NULL in the non-DT
use case.
Nothing will break if pdata->num_regulators is larger than the number
of regulators that the driver defines: pdata->num_regulators is only
read in act8865_get_init_data() to iterate through pdata->regulators.
The error handler might have some value as a sanity check on the
platform data, but the platform data could be broken in many other
ways that are not checked for (unknown IDs, duplicate IDs), so I see
no reason to perform only this specific check.
Signed-off-by: Maarten ter Huurne <maarten@treewalker.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The local variable "dev" already contains a pointer to the device,
so there is no need to take the address of "client->dev" again.
Signed-off-by: Maarten ter Huurne <maarten@treewalker.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The documentation lists both 1.8V and 3.3V for this regulator output,
but 3.3V is mentioned more often and also matches what JZ4770 and
JZ4780 expect as an input.
Note that the voltage of REG9 is not programmable, so this commit only
changes the voltage reported in sysfs and debugfs, not the actual
output voltage of the hardware.
Signed-off-by: Maarten ter Huurne <maarten@treewalker.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no need to preserve its value between calls. I guess this
was a copy-paste slip-up.
Signed-off-by: Maarten ter Huurne <maarten@treewalker.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
For the step-down DC/DC regulators, the output voltage is
selectable by setting VSEL pin that when VSEL is low, output
voltage is programmed by VSET1[] bits, and when VSEL is high,
output voltage is programmed by VSET2[] bits.
The DT property "active-semi,vsel-high" is used to specify
the VSEL pin at high on the board.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The act88600/act8846/act8865 regulators have a number of input supplies
supplying the individual regulators. This may even be recursively like on
most Rockchip boards using the act8846 where REG4 is most of the time
connected to the inl1-supply.
Therefore add the ability to specify the input supplies for the individual inputs.
The input-names are taken from the datasheets of act8600, act8846 and act8865.
On the act8600 some regulators do not have separate input supplies.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds act8600 support to the act8865 driver.
VBUS and USB charger supported by this chip can be added later
Tested on MIPS Creator CI20
Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It reverts commit a4b4e0461e ("of: Add standard property for poweroff capability").
As discussed on the mailing list, it makes more sense to rename back to the
old established property name, without the vendor prefix. Problem being that
the word "source" usually tends to be used for inputs and that is out of control
of the OS. The poweroff capability is an output which simply turns the
system-power off. Also, this property might be used by drivers which power-off
the system and power back on subsequent RTC alarms. This seems to suggest to
remove "poweroff" from the property name and to choose "system-power-controller"
as the more generic name. This patchs adds the required renaming changes and
defines an helper function which checks if this property is set.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
When the property "poweroff-source" is found in the
devicetree, the function pm_power_off is defined. This function sends the
rights bit fields to the global off control register. shutdown/poweroff
commands are now supported for hardware components which use these PMU.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
act8846_matches and act8865_matches are defined only when OF is
enabled. Move references to them to the act8865_pdata_from_dt()
function to avoid a build error when OF is disabled.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add device id and definition of registers and regulators to support
the act8846 PMU.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Tested-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch prepares support for other devices in the act88xx family of
PMUs manufactured by Active-Semi.
http://www.active-semi.com/products/power-management-units/act88xx/
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Tested-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
act8865_pdata_from_dt() populates the array pdata->regulators with all
the regulators and then assigns the field init_data only for the ones
actually found in the DT.
The patch changes the value assigned to pdata->num_regulators to match
the size of the array.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Tested-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Simply use ret variable instead.
Also remove unneeded initialize for ret variable.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The driver loops through all available regulators (ACT8865_REG_NUM)
and accesses pdata->regulators[i].platform_data without checking the
actual value of num_regulators in platform data, potentially causing a
invalid memory access.
Fix this and look up the regulator init_data by id in platform data.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Tested-by Wenyou.Yang <wenyou.yang@atmel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Now we are using devm_regulator_register(), so we don't need the *rdev[] array
to store return value of devm_regulator_register. Use a *rdev variable is
enough for checking return status.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Wenyou Yang <Wenyou.yang@atmel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
of_find_node_by_name walks the allnodes list, and can thus walk
outside of the parent node. Use of_get_child_by_name instead.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fix below build error when !OF:
CC [M] drivers/regulator/act8865-regulator.o
drivers/regulator/act8865-regulator.c: In function 'act8865_pmic_probe':
drivers/regulator/act8865-regulator.c:306:18: error: 'act8865_matches' undeclared (first use in this function)
drivers/regulator/act8865-regulator.c:306:18: note: each undeclared identifier is reported only once for each function it appears in
drivers/regulator/act8865-regulator.c:306:18: error: negative width in bit-field '<anonymous>'
make[2]: *** [drivers/regulator/act8865-regulator.o] Error 1
make[1]: *** [drivers/regulator] Error 2
make: *** [drivers] Error 2
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
As Mark pointed out, the driver should register all regulators
regardless of how many are used in the system in order to aid diagnostics.
But in the previous patch, only register the regulators that are used.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
There is no suspend enable/disable settings mentioned in datasheet,
so just don't implement .set_suspend_[en|dis]able callbacks.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This is not required because current code use devm_regulator_register() to
register regulators.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Wei Yongjun