[ Upstream commit 0b08826726 ]
The function to decide if one zcrypt queue is better than
another one compared two pointers instead of comparing the
values where the pointers refer to. So within the same
zcrypt card when load of each queue was equal just one queue
was used. This effect only appears on relatively lite load,
typically with one thread applications.
This patch fixes the wrong comparison and now the counters
show that requests are balanced equally over all available
queues within the cards.
There is no performance improvement coming with this fix.
As long as the queue depth for an APQN queue is not touched,
processing is not faster when requests are spread over
queues within the same card hardware. So this fix only
beautifies the lszcrypt counter printouts.
Signed-off-by: Harald Freudenberger <freude@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ad3cbf6133 ]
Make sure to check both return code fields before processing the
response. Otherwise we risk operating on invalid data.
Fixes: c9475369bd ("s390/qeth: rework RX/TX checksum offload")
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 02f510f326 ]
Any modification to the takeover IP-ranges requires that we re-evaluate
which IP addresses are takeover-eligible. Otherwise we might do takeover
for some addresses when we no longer should, or vice-versa.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8a03a3692b ]
Modifying the flags of an IP addr object needs to be protected against
eg. concurrent removal of the same object from the IP table.
Fixes: 5f78e29cee ("qeth: optimize IP handling in rx_mode callback")
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b22d73d668 ]
When takeover is switched off, current code clears the 'TAKEOVER' flag on
all IPs. But the flag is also used for RXIP addresses, and those should
not be affected by the takeover mode.
Fix the behaviour by consistenly applying takover logic to NORMAL
addresses only.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7fbd9493f0 ]
Just as for an explicit enable/disable, toggling the takeover mode also
requires that the IP addresses get updated. Otherwise all IPs that were
added to the table before the mode-toggle, get registered with the old
settings.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6d69b1f1eb ]
Using GSO with small MTUs currently results in a substantial throughput
regression - which is caused by how qeth needs to map non-linear skbs
into its IO buffer elements:
compared to a linear skb, each GSO-segmented skb effectively consumes
twice as many buffer elements (ie two instead of one) due to the
additional header-only part. This causes the Output Queue to be
congested with low-utilized IO buffers.
Fix this as follows:
If the MSS is low enough so that a non-SG GSO segmentation produces
order-0 skbs (currently ~3500 byte), opt out from NETIF_F_SG. This is
where we anticipate the biggest savings, since an SG-enabled
GSO segmentation produces skbs that always consume at least two
buffer elements.
Larger MSS values continue to get a SG-enabled GSO segmentation, since
1) the relative overhead of the additional header-only buffer element
becomes less noticeable, and
2) the linearization overhead increases.
With the throughput regression fixed, re-enable NETIF_F_SG by default to
reap the significant CPU savings of GSO.
Fixes: 5722963a8e ("qeth: do not turn on SG per default")
Reported-by: Nils Hoppmann <niho@de.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upsteam commit bc3ab70584 ]
Commit 5f78e29cee ("qeth: optimize IP handling in rx_mode callback")
reworked how secondary addresses are managed for qeth devices.
Instead of dropping & subsequently re-adding all addresses on every
ndo_set_rx_mode() call, qeth now keeps track of the addresses that are
currently registered with the HW.
On a ndo_set_rx_mode(), we thus only need to do (de-)registration
requests for the addresses that have actually changed.
On L3 devices, the lookup for IPv4 Multicast addresses checks the wrong
hashtable - and thus never finds a match. As a result, we first delete
*all* such addresses, and then re-add them again. So each set_rx_mode()
causes a short period where the IPv4 Multicast addresses are not
registered, and the card stops forwarding inbound traffic for them.
Fix this by setting the ->is_multicast flag on the lookup object, thus
enabling qeth_l3_ip_from_hash() to search the correct hashtable and
find a match there.
Fixes: 5f78e29cee ("qeth: optimize IP handling in rx_mode callback")
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0cbff6d454 ]
The current GSO skb size limit was copy&pasted over from the L3 path,
where it is needed due to a TSO limitation.
As L2 devices don't offer TSO support (and thus all GSO skbs are
segmented before they reach the driver), there's no reason to restrict
the stack in how large it may build the GSO skbs.
Fixes: d52aec97e5 ("qeth: enable scatter/gather in layer 2 mode")
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 83cf79a2fe ]
When the allocation of the addr buffer fails, we need to free
our refcount on the inetdevice before returning.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 408358b50d ]
Because we do not make use of the cda (channel data address) for test,
no-op ccws no address translation takes place. This means cda could
contain a guest address which we do not want to attempt to free. Let's
check the command type and skip cda free when it is not needed.
For a TIC ccw, ccw->cda points to either a ccw in an existing chain or
it points to a whole new allocated chain. In either case the data will
be freed when the owning chain is freed.
Signed-off-by: Jason J. Herne <jjherne@linux.vnet.ibm.com>
Reviewed-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Message-Id: <1510068152-21988-1-git-send-email-jjherne@linux.vnet.ibm.com>
Reviewed-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWfswbQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykvEwCfXU1MuYFQGgMdDmAZXEc+xFXZvqgAoKEcHDNA
6dVh26uchcEQLN/XqUDt
=x306
-----END PGP SIGNATURE-----
Merge tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull initial SPDX identifiers from Greg KH:
"License cleanup: add SPDX license identifiers to some files
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the
'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally
binding shorthand, which can be used instead of the full boiler plate
text.
This patch is based on work done by Thomas Gleixner and Kate Stewart
and Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset
of the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to
license had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied
to a file was done in a spreadsheet of side by side results from of
the output of two independent scanners (ScanCode & Windriver)
producing SPDX tag:value files created by Philippe Ombredanne.
Philippe prepared the base worksheet, and did an initial spot review
of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537
files assessed. Kate Stewart did a file by file comparison of the
scanner results in the spreadsheet to determine which SPDX license
identifier(s) to be applied to the file. She confirmed any
determination that was not immediately clear with lawyers working with
the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained
>5 lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that
was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that
became the concluded license(s).
- when there was disagreement between the two scanners (one detected
a license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply
(and which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases,
confirmation by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.
The Windriver scanner is based on an older version of FOSSology in
part, so they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot
checks in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect
the correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial
patch version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch
license was not GPL-2.0 WITH Linux-syscall-note to ensure that the
applied SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
License cleanup: add SPDX license identifier to uapi header files with a license
License cleanup: add SPDX license identifier to uapi header files with no license
License cleanup: add SPDX GPL-2.0 license identifier to files with no license
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Six fixes for mostly minor issues, most of which have small race
windows for occurring.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=6jlR
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Six fixes for mostly minor issues, most of which have small race
windows for occurring"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: Suppress a kernel warning in case the prep function returns BLKPREP_DEFER
scsi: sg: Re-fix off by one in sg_fill_request_table()
scsi: aacraid: Fix controller initialization failure
scsi: hpsa: Fix configured_logical_drive_count·check
scsi: qla2xxx: Initialize Work element before requesting IRQs
scsi: zfcp: fix erp_action use-before-initialize in REC action trace
v4.10 commit 6f2ce1c6af ("scsi: zfcp: fix rport unblock race with LUN
recovery") extended accessing parent pointer fields of struct
zfcp_erp_action for tracing. If an erp_action has never been enqueued
before, these parent pointer fields are uninitialized and NULL. Examples
are zfcp objects freshly added to the parent object's children list,
before enqueueing their first recovery subsequently. In
zfcp_erp_try_rport_unblock(), we iterate such list. Accessing erp_action
fields can cause a NULL pointer dereference. Since the kernel can read
from lowcore on s390, it does not immediately cause a kernel page
fault. Instead it can cause hangs on trying to acquire the wrong
erp_action->adapter->dbf->rec_lock in zfcp_dbf_rec_action_lvl()
^bogus^
while holding already other locks with IRQs disabled.
Real life example from attaching lots of LUNs in parallel on many CPUs:
crash> bt 17723
PID: 17723 TASK: ... CPU: 25 COMMAND: "zfcperp0.0.1800"
LOWCORE INFO:
-psw : 0x0404300180000000 0x000000000038e424
-function : _raw_spin_lock_wait_flags at 38e424
...
#0 [fdde8fc90] zfcp_dbf_rec_action_lvl at 3e0004e9862 [zfcp]
#1 [fdde8fce8] zfcp_erp_try_rport_unblock at 3e0004dfddc [zfcp]
#2 [fdde8fd38] zfcp_erp_strategy at 3e0004e0234 [zfcp]
#3 [fdde8fda8] zfcp_erp_thread at 3e0004e0a12 [zfcp]
#4 [fdde8fe60] kthread at 173550
#5 [fdde8feb8] kernel_thread_starter at 10add2
zfcp_adapter
zfcp_port
zfcp_unit <address>, 0x404040d600000000
scsi_device NULL, returning early!
zfcp_scsi_dev.status = 0x40000000
0x40000000 ZFCP_STATUS_COMMON_RUNNING
crash> zfcp_unit <address>
struct zfcp_unit {
erp_action = {
adapter = 0x0,
port = 0x0,
unit = 0x0,
},
}
zfcp_erp_action is always fully embedded into its container object. Such
container object is never moved in its object tree (only add or delete).
Hence, erp_action parent pointers can never change.
To fix the issue, initialize the erp_action parent pointers before
adding the erp_action container to any list and thus before it becomes
accessible from outside of its initializing function.
In order to also close the time window between zfcp_erp_setup_act()
memsetting the entire erp_action to zero and setting the parent pointers
again, drop the memset and instead explicitly initialize individually
all erp_action fields except for parent pointers. To be extra careful
not to introduce any other unintended side effect, even keep zeroing the
erp_action fields for list and timer. Also double-check with
WARN_ON_ONCE that erp_action parent pointers never change, so we get to
know when we would deviate from previous behavior.
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Fixes: 6f2ce1c6af ("scsi: zfcp: fix rport unblock race with LUN recovery")
Cc: <stable@vger.kernel.org> #2.6.32+
Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In some situations we don't receive notification from firmware that
a previously unusable channelpath is usable again.
Schedule recovery for devices that return from path verification
without using all potentially usable paths. The recovery thread will
periodically trigger a path verification on the affected devices.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Suggested-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Reviewed-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix these warnings found by sparse:
drivers/s390/block/scm_blk.c:257:24: warning: incorrect type in assignment (different base types)
drivers/s390/block/scm_blk.c:257:24: expected int [signed] <noident>
drivers/s390/block/scm_blk.c:257:24: got restricted blk_status_t [usertype] error
drivers/s390/block/scm_blk.c:420:33: warning: incorrect type in argument 2 (different base types)
drivers/s390/block/scm_blk.c:420:33: expected restricted blk_status_t [usertype] error
drivers/s390/block/scm_blk.c:420:33: got int [signed] <noident>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Reported-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix a panic in blk_mq_hctx_has_pending() that is caused by a racy call to
blk_mq_run_hw_queues in a dasd function that might get called with the
request queue not yet initialized during initialization.
Signed-off-by: Stefan Haberland <sth@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Pull more s390 updates from Martin Schwidefsky:
"The second patch set for the 4.14 merge window:
- Convert the dasd device driver to the blk-mq interface.
- Provide three zcrypt interfaces for vfio_ap. These will be required
for KVM guest access to the crypto cards attached via the AP bus.
- A couple of memory management bug fixes."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/dasd: blk-mq conversion
s390/mm: use a single lock for the fields in mm_context_t
s390/mm: fix race on mm->context.flush_mm
s390/mm: fix local TLB flushing vs. detach of an mm address space
s390/zcrypt: externalize AP queue interrupt control
s390/zcrypt: externalize AP config info query
s390/zcrypt: externalize test AP queue
s390/mm: use VM_BUG_ON in crst_table_[upgrade|downgrade]
Use new blk-mq interfaces. Use multiple queues and also use the block
layer complete helper that finish the IO on the CPU that initiated it.
Reviewed-by: Jan Hoeppner <hoeppner@linux.vnet.ibm.com>
Signed-off-by: Stefan Haberland <sth@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This is mostly updates of the usual suspects: lpfc, qla2xxx, hisi_sas, megaraid_sas, zfcp and a host of minor updates.
The major driver change here is the elimination of the block based
cciss driver in favour of the SCSI based hpsa driver (which now drives
all the legacy cases cciss used to be required for). Plus a reset
handler clean up and the redo of the SAS SMP handler to use bsg lib.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=nQUG
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly updates of the usual suspects: lpfc, qla2xxx, hisi_sas,
megaraid_sas, zfcp and a host of minor updates.
The major driver change here is the elimination of the block based
cciss driver in favour of the SCSI based hpsa driver (which now drives
all the legacy cases cciss used to be required for). Plus a reset
handler clean up and the redo of the SAS SMP handler to use bsg lib"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (279 commits)
scsi: scsi-mq: Always unprepare before requeuing a request
scsi: Show .retries and .jiffies_at_alloc in debugfs
scsi: Improve requeuing behavior
scsi: Call scsi_initialize_rq() for filesystem requests
scsi: qla2xxx: Reset the logo flag, after target re-login.
scsi: qla2xxx: Fix slow mem alloc behind lock
scsi: qla2xxx: Clear fc4f_nvme flag
scsi: qla2xxx: add missing includes for qla_isr
scsi: qla2xxx: Fix an integer overflow in sysfs code
scsi: aacraid: report -ENOMEM to upper layer from aac_convert_sgraw2()
scsi: aacraid: get rid of one level of indentation
scsi: aacraid: fix indentation errors
scsi: storvsc: fix memory leak on ring buffer busy
scsi: scsi_transport_sas: switch to bsg-lib for SMP passthrough
scsi: smartpqi: remove the smp_handler stub
scsi: hpsa: remove the smp_handler stub
scsi: bsg-lib: pass the release callback through bsg_setup_queue
scsi: Rework handling of scsi_device.vpd_pg8[03]
scsi: Rework the code for caching Vital Product Data (VPD)
scsi: rcu: Introduce rcu_swap_protected()
...
Pull block layer updates from Jens Axboe:
"This is the first pull request for 4.14, containing most of the code
changes. It's a quiet series this round, which I think we needed after
the churn of the last few series. This contains:
- Fix for a registration race in loop, from Anton Volkov.
- Overflow complaint fix from Arnd for DAC960.
- Series of drbd changes from the usual suspects.
- Conversion of the stec/skd driver to blk-mq. From Bart.
- A few BFQ improvements/fixes from Paolo.
- CFQ improvement from Ritesh, allowing idling for group idle.
- A few fixes found by Dan's smatch, courtesy of Dan.
- A warning fixup for a race between changing the IO scheduler and
device remova. From David Jeffery.
- A few nbd fixes from Josef.
- Support for cgroup info in blktrace, from Shaohua.
- Also from Shaohua, new features in the null_blk driver to allow it
to actually hold data, among other things.
- Various corner cases and error handling fixes from Weiping Zhang.
- Improvements to the IO stats tracking for blk-mq from me. Can
drastically improve performance for fast devices and/or big
machines.
- Series from Christoph removing bi_bdev as being needed for IO
submission, in preparation for nvme multipathing code.
- Series from Bart, including various cleanups and fixes for switch
fall through case complaints"
* 'for-4.14/block' of git://git.kernel.dk/linux-block: (162 commits)
kernfs: checking for IS_ERR() instead of NULL
drbd: remove BIOSET_NEED_RESCUER flag from drbd_{md_,}io_bio_set
drbd: Fix allyesconfig build, fix recent commit
drbd: switch from kmalloc() to kmalloc_array()
drbd: abort drbd_start_resync if there is no connection
drbd: move global variables to drbd namespace and make some static
drbd: rename "usermode_helper" to "drbd_usermode_helper"
drbd: fix race between handshake and admin disconnect/down
drbd: fix potential deadlock when trying to detach during handshake
drbd: A single dot should be put into a sequence.
drbd: fix rmmod cleanup, remove _all_ debugfs entries
drbd: Use setup_timer() instead of init_timer() to simplify the code.
drbd: fix potential get_ldev/put_ldev refcount imbalance during attach
drbd: new disk-option disable-write-same
drbd: Fix resource role for newly created resources in events2
drbd: mark symbols static where possible
drbd: Send P_NEG_ACK upon write error in protocol != C
drbd: add explicit plugging when submitting batches
drbd: change list_for_each_safe to while(list_first_entry_or_null)
drbd: introduce drbd_recv_header_maybe_unplug
...
Pull networking updates from David Miller:
1) Support ipv6 checksum offload in sunvnet driver, from Shannon
Nelson.
2) Move to RB-tree instead of custom AVL code in inetpeer, from Eric
Dumazet.
3) Allow generic XDP to work on virtual devices, from John Fastabend.
4) Add bpf device maps and XDP_REDIRECT, which can be used to build
arbitrary switching frameworks using XDP. From John Fastabend.
5) Remove UFO offloads from the tree, gave us little other than bugs.
6) Remove the IPSEC flow cache, from Florian Westphal.
7) Support ipv6 route offload in mlxsw driver.
8) Support VF representors in bnxt_en, from Sathya Perla.
9) Add support for forward error correction modes to ethtool, from
Vidya Sagar Ravipati.
10) Add time filter for packet scheduler action dumping, from Jamal Hadi
Salim.
11) Extend the zerocopy sendmsg() used by virtio and tap to regular
sockets via MSG_ZEROCOPY. From Willem de Bruijn.
12) Significantly rework value tracking in the BPF verifier, from Edward
Cree.
13) Add new jump instructions to eBPF, from Daniel Borkmann.
14) Rework rtnetlink plumbing so that operations can be run without
taking the RTNL semaphore. From Florian Westphal.
15) Support XDP in tap driver, from Jason Wang.
16) Add 32-bit eBPF JIT for ARM, from Shubham Bansal.
17) Add Huawei hinic ethernet driver.
18) Allow to report MD5 keys in TCP inet_diag dumps, from Ivan
Delalande.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1780 commits)
i40e: point wb_desc at the nvm_wb_desc during i40e_read_nvm_aq
i40e: avoid NVM acquire deadlock during NVM update
drivers: net: xgene: Remove return statement from void function
drivers: net: xgene: Configure tx/rx delay for ACPI
drivers: net: xgene: Read tx/rx delay for ACPI
rocker: fix kcalloc parameter order
rds: Fix non-atomic operation on shared flag variable
net: sched: don't use GFP_KERNEL under spin lock
vhost_net: correctly check tx avail during rx busy polling
net: mdio-mux: add mdio_mux parameter to mdio_mux_init()
rxrpc: Make service connection lookup always check for retry
net: stmmac: Delete dead code for MDIO registration
gianfar: Fix Tx flow control deactivation
cxgb4: Ignore MPS_TX_INT_CAUSE[Bubble] for T6
cxgb4: Fix pause frame count in t4_get_port_stats
cxgb4: fix memory leak
tun: rename generic_xdp to skb_xdp
tun: reserve extra headroom only when XDP is set
net: dsa: bcm_sf2: Configure IMP port TC2QOS mapping
net: dsa: bcm_sf2: Advertise number of egress queues
...
KVM has a need to control the interrupts on real and virtualized
AP queue devices. This fix provides a new function to control
the interrupt facilities of an AP queue device.
Signed-off-by: Harald Freudenberger <freude@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
KVM has a need to fetch the crypto configuration information
as it is returned by the PQAP(QCI) instruction. This patch
introduces a new API ap_query_configuration() which provides
this info in a handy way for the caller.
Signed-off-by: Harald Freudenberger <freude@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Under certain specified conditions, the Test AP Queue (TAPQ)
subfunction of the Process Adjunct Processor Queue (PQAP) instruction
will be intercepted by a guest VM. The guest VM must have a means for
executing the intercepted instruction.
The vfio_ap driver will provide an interface to execute the
PQAP(TAPQ) instruction subfunction on behalf of a guest VM.
The code for executing the AP instructions currently resides in the
AP bus. This patch refactors the AP bus code to externalize access
to the PQAP(TAPQ) instruction subfunction to make it available to
the vfio_ap driver.
Signed-off-by: Tony Krowiak <akrowiak@linux.vnet.ibm.com>
Signed-off-by: Harald Freudenberger <freude@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Pull s390 updates from Martin Schwidefsky:
"The first part of the s390 updates for 4.14:
- Add machine type 0x3906 for IBM z14
- Add IBM z14 TLB flushing improvements for KVM guests
- Exploit the TOD clock epoch extension to provide a continuous TOD
clock afer 2042/09/17
- Add NIAI spinlock hints for IBM z14
- Rework the vmcp driver and use CMA for the respone buffer of z/VM
CP commands
- Drop some s390 specific asm headers and use the generic version
- Add block discard for DASD-FBA devices under z/VM
- Add average request times to DASD statistics
- A few of those constify patches which seem to be in vogue right now
- Cleanup and bug fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (50 commits)
s390/mm: avoid empty zero pages for KVM guests to avoid postcopy hangs
s390/dasd: Add discard support for FBA devices
s390/zcrypt: make CPRBX const
s390/uaccess: avoid mvcos jump label
s390/mm: use generic mm_hooks
s390/facilities: fix typo
s390/vmcp: simplify vmcp_response_free()
s390/topology: Remove the unused parent_node() macro
s390/dasd: Change unsigned long long to unsigned long
s390/smp: convert cpuhp_setup_state() return code to zero on success
s390: fix 'novx' early parameter handling
s390/dasd: add average request times to dasd statistics
s390/scm: use common completion path
s390/pci: log changes to uid checking
s390/vmcp: simplify vmcp_ioctl()
s390/vmcp: return -ENOTTY for unknown ioctl commands
s390/vmcp: split vmcp header file and move to uapi
s390/vmcp: make use of contiguous memory allocator
s390/cpcmd,vmcp: avoid GFP_DMA allocations
s390/vmcp: fix uaccess check and avoid undefined behavior
...
The z/VM hypervisor provides virtual disks (VDISK) which are backed by
main memory of the hypervisor. Those devices are seen as DASD FBA disks
within the Linux guest.
Whenever data is written to such a device, memory is allocated
on-the-fly by z/VM accordingly. This memory, however, is not being freed
if data on the device is deleted by the guest OS.
In order to make memory usable after deletion again, add discard support
to the FBA discipline.
While at it, update comments regarding the DASD_FEATURE_* flags.
Reviewed-by: Stefan Haberland <sth@linux.vnet.ibm.com>
Signed-off-by: Jan Höppner <hoeppner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Make this const as it is only used in a copy operation.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Harald Freudenberger <freude@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Get rid of the goto and "out" label within vmcp_response_free() which
I added. This just makes the code harder to read than necessary.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This way we don't need a block_device structure to submit I/O. The
block_device has different life time rules from the gendisk and
request_queue and is usually only available when the block device node
is open. Other callers need to explicitly create one (e.g. the lightnvm
passthrough code, or the new nvme multipathing code).
For the actual I/O path all that we need is the gendisk, which exists
once per block device. But given that the block layer also does
partition remapping we additionally need a partition index, which is
used for said remapping in generic_make_request.
Note that all the block drivers generally want request_queue or
sometimes the gendisk, so this removes a layer of indirection all
over the stack.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Unsigned long long and unsigned long were different in size for 31-bit.
For 64-bit the size for both datatypes is 8 Bytes and since the support
for 31-bit is long gone we can clean up a little and change everything
to unsigned long.
Change get_phys_clock() along the way to accept unsigned long as well so
that the DASD code can be consistent.
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Jan Höppner <hoeppner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add average times to the DASD statistics interface.
Signed-off-by: Stefan Haberland <sth@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Taking a full copy via skb_realloc_headroom() on every xmit is overkill
and wastes CPU time; all we actually need is to push on the qeth_hdr.
So rework the L2 OSA TX path to avoid the copy.
Minor complications arise because struct qeth_hdr must not cross a page
boundary. So add a new helper qeth_push_hdr() that catches this, and
falls back to the hdr cache that we already use for IQDs.
This change uncovered that qeth's TX completion takes rather long.
Now that we no longer free the original skb straight away and thus call
skb->destructor later than before, throughput regresses significantly.
For now, restore old behaviour by adding an explicit skb_orphan(),
and a big TODO to improve the TX completion time.
Tested-by: Nils Hoppmann <niho@de.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After plenty of refactoring, use hd_len as single indication that
the skb needs a dedicated header element.
This preserves existing behaviour for TSO, as 'hdr' always points
to skb->data.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a prerequisite for unifying the code to build header elements.
The TSO header has a different size, so we can no longer rely on implicitly
adding the size of a normal qeth_hdr.
No functional change.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For TSO we need to skip the skb's qeth/IP/TCP headers when mapping
it into buffer elements. Instead of (mis)using skb_pull(), pass a
corresponding offset to fill_buffer() like we already do for IQDs.
No actual change in the resulting TSO buffers.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TSO code already calculates the length of its header element,
no need to duplicate this in the low-level code again.
Use this opportunity to make hd_len unsigned, and for TSO match
its calculation to what tso_fill_header() does.
No functional change.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For IQD we already need to fix up the qeth_hdr's length field, and
future changes will require more flexibility for OSA as well. The
device-specific path knows best what header length it requires, so just
pass it from there.
While at it, remove the unused qeth_card parameter.
No functional change.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
l2_hard_start_xmit() actually doesn't contain much shared code,
and having device-specific paths makes isolated changes a lot easier.
So split it into three routines for IQD, OSN and OSD/OSM/OSX.
No functional change.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IP-address setting and removal are delayed when the device is not yet in
state SOFTSETUP or UP. ref_counter has been implemented only for
ip-address with type normal. In this patch ref_counter logic is also used
for ip-address with type rxip to allow appropriate handling of multiple
postponed rxip add and del calls.
Signed-off-by: Kittipon Meesompop <kmeesomp@linux.vnet.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
change trace-messages:
- from addrxip4 to delrxip4
- from addrxip6 to delrxip6
Signed-off-by: Kittipon Meesompop <kmeesomp@linux.vnet.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There exist different commands to add unicast and multicast addresses on
the OSA card. rxip addresses are always set as unicast addresses and
thus just unicast addresses should be allowed.
Adding a multicast address now fails and a grace message is generated.
Signed-off-by: Kittipon Meesompop <kmeesomp@linux.vnet.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Consolidation of duplicated code, no functional change.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clean up the inline cruft in s390 net drivers. Many of the inlined
functions had only one caller anyway.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace some open-coded parts with their proper API calls.
Also remove two skb_[re]set_mac_header() calls in the L2
xmit paths that are clearly no longer required, since at least
commit 6d1ccff627 ("net: reset mac header in dev_start_xmit()").
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For some xmit paths we pass down a data offset to qeth_fill_buffer(),
to indicate that the first k bytes of the skb should be skipped when
mapping it into buffer elements.
Commit acd9776b5c ("s390/qeth: no ETH header for outbound AF_IUCV")
recently switched the offset for the IUCV-over-HiperSockets path
from 0 to ETH_HLEN, and now we have
device offset
OSA = 0
IQD > 0
for all xmit paths.
OSA would previously pass down -1 from do_send_packet(), to distinguish
between 1) OSA and 2) IQD with offset 0. That's no longer needed now,
so have it pass 0, make the offset unsigned and clean up how we apply
the offset in __qeth_fill_buffer().
No change of behaviour for any of our current xmit paths.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. for adjusting the buffer's next_element_to_fill in __fill_buffer(),
just pass the full qeth_qdio_out_buffer struct
2. when adding a header element, be consistent about passing
a hint ('is_first_elem') to __fill_buffer()
No functional change.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Improve readability of the code that determines a buffer element's
fragment type, and reduce the number of cases down from 5 to 3.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qeth_l3_setadapter_parms() queries the device for supported
adapterparms, even though they already have been queried as part of the
device's high-level setup. Remove that extra call.
The only call chain for qeth_l3_setadapter_parms() is
__qeth_l3_set_online()
qeth_core_hardsetup_card()
qeth_query_setadapterparms()
qeth_l3_setadapter_parms()
qeth_query_setadapterparms()
, and we only reach qeth_l3_setadapter_parms() if the first
adapterparms query succeeds. Hence removing the second query results in
no loss of functionality.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qeth_l2_request_initial_mac() queries the device for its supported
adapterparms, even though they already have been queried as part of the
device's high-level setup. Remove that extra call.
The only call chain for qeth_l2_request_initial_mac() is
__qeth_l2_set_online()
qeth_core_hardsetup_card()
qeth_query_setadapterparms()
qeth_l2_setup_netdev()
qeth_l2_request_initial_mac()
qeth_query_setadapterparms()
, and we only reach qeth_l2_request_initial_mac() if the first
adapterparms query succeeds. Hence removing the second query results in
no loss of functionality.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After transmitting a skb via send_packet[_fast](), the statistics
code accesses the skb once more to account for transmitted page frags.
This has a (theoretical?) race against the TX completion - if the TX
completion is processed and frees the skb before hard_start_xmit()
gets to the statistics part, we access random memory.
Fix this by caching the # of page frags, before the skb is transmitted.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds early checks to avoid burning CPU cycles on
the assembly of trace entries which would be skipped anyway.
Introduce a static const variable to keep the trace level to check with
debug_level_enabled() in sync with the actual trace emit with
debug_event(). In order not to refactor the SAN tracing too much,
simply use a define instead.
This change is only for the non / semi hot paths,
while the actual (I/O) hot path was already improved earlier:
zfcp_dbf_scsi() is already guarded by its only caller _zfcp_dbf_scsi()
since commit dcd20e2316 ("[SCSI] zfcp: Only collect SCSI debug data for
matching trace levels").
zfcp_dbf_hba_fsf_res() is already guarded by its only caller
zfcp_dbf_hba_fsf_response() since commit 2e261af84c ("[SCSI] zfcp: Only
collect FSF/HBA debug data for matching trace levels").
Signed-off-by: Martin Peschke <mpeschke@linux.vnet.ibm.com>
[maier@linux.vnet.ibm.com: rebase, reword, default level 3 branch prediction]
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Improves commit 43f60cbd56 ("[SCSI] zfcp: No automatic port_rescan on
events")
Signed-off-by: Martin Peschke <mpeschke@linux.vnet.ibm.com>
[maier@linux.vnet.ibm.com: reword, underscore in description to match sysfs]
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
v2.6.38 commit a54ca0f62f ("[SCSI] zfcp: Redesign of the debug tracing
for HBA records.")
dropped trace information previously introduced with
v2.6.27 commit c3baa9a26c ("[SCSI] zfcp: Add information about interrupt
to trace.")
but kept and needlessly assigned a now no longer used struct field.
Signed-off-by: Martin Peschke <mpeschke@linux.vnet.ibm.com>
[maier@linux.vnet.ibm.com: reword, added git history]
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit a54ca0f62f ("[SCSI] zfcp: Redesign of the debug tracing for HBA
records.") refactored zfcp_dbf_hba_berr into zfcp_dbf_hba_bit_err
but added the prototype for the latter without removing it for the former.
Suggested-by: Martin Peschke <mpeschke@linux.vnet.ibm.com>
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Martin Peschke <mpeschke@linux.vnet.ibm.com>
[maier@linux.vnet.ibm.com: re-worded short description for more details]
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Improves commit 250a1352b9 ("[SCSI] zfcp: Redesign of the debug tracing
for SCSI records.")
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Just to silence sparse. Since zfcp only exists for s390 and
s390 is big endian, this has been working correctly without conversions
and all the new conversions are NOPs so no performance impact.
Nonetheless, use the conversion on the constant expression where possible.
NB: N_Port-IDs have always been handled with hton24 or ntoh24 conversions
because they also convert to / from character array.
Affected common code structs and .fields are:
HOT I/O PATH:
fcp_cmnd .fc_dl
FCP command: regular SCSI I/O, including DIX case
SEMI-HOT I/O PATH:
fcp_cmnd .fc_dl
recovery FCP command: task management function (LUN / target reset)
fcp_resp_ext
FCP response having FCP_SNS_LEN_VAL with .fr_rsp_len .fr_sns_len
FCP response having FCP_RESID_UNDER with .fr_resid
RECOVERY / DISCOVERY PATHS:
fc_ct_hdr .ct_cmd .ct_mr_size
zfcp auto port scan [GPN_FT] with fc_gpn_ft_resp.fp_wwpn,
recovery for returned port [GID_PN] with fc_ns_gid_pn.fn_wwpn,
get symbolic port name [GSPN],
register symbolic port name [RSPN] (NPIV only).
fc_els_rscn .rscn_plen
incoming ELS (RSCN).
fc_els_flogi .fl_wwpn .fl_wwnn
incoming ELS (PLOGI),
port open response with .fl_csp.sp_bb_data .fl_cssp[0..3].cp_class,
FCP channel physical port,
point-to-point peer (P2P only).
fc_els_logo .fl_n_port_wwn
incoming ELS (LOGO).
fc_els_adisc .adisc_wwnn .adisc_wwpn
path test after RSCN for gone target port.
Since v4.10 commit 05de97003c ("linux/types.h: enable endian checks for
all sparse builds"), below sparse endianness reports appear by default.
Previously, one needed to pass argument CF="-D__CHECK_ENDIAN__" to make
as in: $ make C=1 CF="-D__CHECK_ENDIAN__" M=drivers/s390/scsi.
Silenced sparse warnings and one error:
$ make C=1 M=drivers/s390/scsi
...
CHECK drivers/s390/scsi/zfcp_dbf.c
drivers/s390/scsi/zfcp_dbf.c:463:22: warning: restricted __be16 degrades to integer
drivers/s390/scsi/zfcp_dbf.c:476:28: warning: restricted __be16 degrades to integer
CC drivers/s390/scsi/zfcp_dbf.o
...
CHECK drivers/s390/scsi/zfcp_fc.c
drivers/s390/scsi/zfcp_fc.c:263:26: warning: restricted __be16 degrades to integer
drivers/s390/scsi/zfcp_fc.c:299:41: warning: incorrect type in argument 2 (different base types)
drivers/s390/scsi/zfcp_fc.c:299:41: expected unsigned long long [unsigned] [usertype] wwpn
drivers/s390/scsi/zfcp_fc.c:299:41: got restricted __be64 [usertype] fl_wwpn
drivers/s390/scsi/zfcp_fc.c:309:40: warning: incorrect type in argument 2 (different base types)
drivers/s390/scsi/zfcp_fc.c:309:40: expected unsigned long long [unsigned] [usertype] wwpn
drivers/s390/scsi/zfcp_fc.c:309:40: got restricted __be64 [usertype] fl_n_port_wwn
drivers/s390/scsi/zfcp_fc.c:338:31: warning: restricted __be16 degrades to integer
drivers/s390/scsi/zfcp_fc.c:355:24: warning: incorrect type in assignment (different base types)
drivers/s390/scsi/zfcp_fc.c:355:24: expected restricted __be16 [usertype] ct_cmd
drivers/s390/scsi/zfcp_fc.c:355:24: got unsigned short [unsigned] [usertype] cmd
drivers/s390/scsi/zfcp_fc.c:356:28: warning: incorrect type in assignment (different base types)
drivers/s390/scsi/zfcp_fc.c:356:28: expected restricted __be16 [usertype] ct_mr_size
drivers/s390/scsi/zfcp_fc.c:356:28: got int
drivers/s390/scsi/zfcp_fc.c:379:36: warning: incorrect type in assignment (different base types)
drivers/s390/scsi/zfcp_fc.c:379:36: expected restricted __be64 [usertype] fn_wwpn
drivers/s390/scsi/zfcp_fc.c:379:36: got unsigned long long [unsigned] [usertype] wwpn
drivers/s390/scsi/zfcp_fc.c:463:18: warning: restricted __be64 degrades to integer
drivers/s390/scsi/zfcp_fc.c:465:17: warning: cast from restricted __be64
drivers/s390/scsi/zfcp_fc.c:473:20: warning: incorrect type in assignment (different base types)
drivers/s390/scsi/zfcp_fc.c:473:20: expected unsigned long long [unsigned] [usertype] wwnn
drivers/s390/scsi/zfcp_fc.c:473:20: got restricted __be64 [usertype] fl_wwnn
drivers/s390/scsi/zfcp_fc.c:474:29: warning: incorrect type in assignment (different base types)
drivers/s390/scsi/zfcp_fc.c:474:29: expected unsigned int [unsigned] [usertype] maxframe_size
drivers/s390/scsi/zfcp_fc.c:474:29: got restricted __be16 [usertype] sp_bb_data
drivers/s390/scsi/zfcp_fc.c:476:30: warning: restricted __be16 degrades to integer
drivers/s390/scsi/zfcp_fc.c:478:30: warning: restricted __be16 degrades to integer
drivers/s390/scsi/zfcp_fc.c:480:30: warning: restricted __be16 degrades to integer
drivers/s390/scsi/zfcp_fc.c:482:30: warning: restricted __be16 degrades to integer
drivers/s390/scsi/zfcp_fc.c:500:28: warning: incorrect type in assignment (different base types)
drivers/s390/scsi/zfcp_fc.c:500:28: expected unsigned long long [unsigned] [usertype] wwnn
drivers/s390/scsi/zfcp_fc.c:500:28: got restricted __be64 [usertype] adisc_wwnn
drivers/s390/scsi/zfcp_fc.c:502:38: warning: restricted __be64 degrades to integer
drivers/s390/scsi/zfcp_fc.c:541:40: warning: incorrect type in assignment (different base types)
drivers/s390/scsi/zfcp_fc.c:541:40: expected restricted __be64 [usertype] adisc_wwpn
drivers/s390/scsi/zfcp_fc.c:541:40: got unsigned long long [unsigned] [usertype] port_name
drivers/s390/scsi/zfcp_fc.c:542:40: warning: incorrect type in assignment (different base types)
drivers/s390/scsi/zfcp_fc.c:542:40: expected restricted __be64 [usertype] adisc_wwnn
drivers/s390/scsi/zfcp_fc.c:542:40: got unsigned long long [unsigned] [usertype] node_name
drivers/s390/scsi/zfcp_fc.c:669:16: warning: restricted __be16 degrades to integer
drivers/s390/scsi/zfcp_fc.c:696:24: warning: restricted __be64 degrades to integer
drivers/s390/scsi/zfcp_fc.c:699:54: warning: incorrect type in argument 2 (different base types)
drivers/s390/scsi/zfcp_fc.c:699:54: expected unsigned long long [unsigned] [usertype] <noident>
drivers/s390/scsi/zfcp_fc.c:699:54: got restricted __be64 [usertype] fp_wwpn
CC drivers/s390/scsi/zfcp_fc.o
CHECK drivers/s390/scsi/zfcp_fsf.c
drivers/s390/scsi/zfcp_fsf.c:479:34: warning: incorrect type in assignment (different base types)
drivers/s390/scsi/zfcp_fsf.c:479:34: expected unsigned long long [unsigned] [usertype] port_name
drivers/s390/scsi/zfcp_fsf.c:479:34: got restricted __be64 [usertype] fl_wwpn
drivers/s390/scsi/zfcp_fsf.c:480:34: warning: incorrect type in assignment (different base types)
drivers/s390/scsi/zfcp_fsf.c:480:34: expected unsigned long long [unsigned] [usertype] node_name
drivers/s390/scsi/zfcp_fsf.c:480:34: got restricted __be64 [usertype] fl_wwnn
drivers/s390/scsi/zfcp_fsf.c:506:36: warning: incorrect type in assignment (different base types)
drivers/s390/scsi/zfcp_fsf.c:506:36: expected unsigned long long [unsigned] [usertype] peer_wwpn
drivers/s390/scsi/zfcp_fsf.c:506:36: got restricted __be64 [usertype] fl_wwpn
drivers/s390/scsi/zfcp_fsf.c:507:36: warning: incorrect type in assignment (different base types)
drivers/s390/scsi/zfcp_fsf.c:507:36: expected unsigned long long [unsigned] [usertype] peer_wwnn
drivers/s390/scsi/zfcp_fsf.c:507:36: got restricted __be64 [usertype] fl_wwnn
drivers/s390/scsi/zfcp_fc.h:269:46: warning: restricted __be32 degrades to integer
drivers/s390/scsi/zfcp_fc.h:270:29: error: incompatible types in comparison expression (different base types)
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This eases crash dump analysis by automatically dissecting these
protocol headers at least somewhat rather than getting a string
interpretation of large unstructured character array buffer fields.
Also, we can get rid of some unnecessary and error-prone type casts.
This change is possible since v2.6.33 commit 4318e08c84
("[SCSI] zfcp: Update FCP protocol related code").
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
v2.6.33 commit dbf5dfe9db ("[SCSI] zfcp: Use common code definitions for
FC CT structs") replaced own definitions with common code definitions.
While FC_BA_RJT_UNABLE happens to be defined with the same value 9 as
FC_FS_RJT_UNABL and thus also works, here we should use the latter from
fc_gs.h.
See also its use in libfc's fc_disc_gpn_ft_resp().
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Complements debugging aspects of the otherwise functionally complete
v3.17 commit 9cb78c16f5 ("scsi: use 64-bit LUNs").
While I don't have access to a target exporting 3 or 4 level LUNs,
I did test it by explicitly attaching a non-existent fake 4 level LUN
by means of zfcp sysfs attribute "unit_add".
In order to see corresponding trace records of otherwise successful
events, we had to increase the trace level of area SCSI and HBA to 6.
$ echo 6 > /sys/kernel/debug/s390dbf/zfcp_0.0.1880_scsi/level
$ echo 6 > /sys/kernel/debug/s390dbf/zfcp_0.0.1880_hba/level
$ echo 0x4011402240334044 > \
/sys/bus/ccw/drivers/zfcp/0.0.1880/0x50050763031bd327/unit_add
Example output formatted by an updated zfcpdbf from the s390-tools
package interspersed with kernel messages at scsi_logging_level=4605:
Timestamp : ...
Area : REC
Subarea : 00
Level : 1
Exception : -
CPU ID : ..
Caller : 0x...
Record ID : 1
Tag : scsla_1
LUN : 0x4011402240334044
WWPN : 0x50050763031bd327
D_ID : 0x00......
Adapter status : 0x5400050b
Port status : 0x54000001
LUN status : 0x41000000
Ready count : 0x00000001
Running count : 0x00000000
ERP want : 0x01
ERP need : 0x01
scsi 2:0:0:4630896905707208721: scsi scan: INQUIRY pass 1 length 36
scsi 2:0:0:4630896905707208721: scsi scan: INQUIRY successful with code 0x0
Timestamp : ...
Area : HBA
Subarea : 00
Level : 6
Exception : -
CPU ID : ..
Caller : 0x...
Record ID : 1
Tag : fs_norm
Request ID : 0x<inquiry2-req-id>
Request status : 0x00000010
FSF cmnd : 0x00000001
FSF sequence no: 0x...
FSF issued : ...
FSF stat : 0x00000000
FSF stat qual : 00000000 00000000 00000000 00000000
Prot stat : 0x00000001
Prot stat qual : ........ ........ 00000000 00000000
Port handle : 0x...
LUN handle : 0x...
|
Timestamp : ...
Area : SCSI
Subarea : 00
Level : 6
Exception : -
CPU ID : ..
Caller : 0x...
Record ID : 1
Tag : rsl_nor
Request ID : 0x<inquiry2-req-id>
SCSI ID : 0x00000000
SCSI LUN : 0x40224011
SCSI LUN high : 0x40444033 <=======================
SCSI result : 0x00000000
SCSI retries : 0x00
SCSI allowed : 0x03
SCSI scribble : 0x<inquiry2-req-id>
SCSI opcode : 12000000 a4000000 00000000 00000000
FCP rsp inf cod: 0x00
FCP rsp IU : 00000000 00000000 00000000 00000000
00000000 00000000
scsi 2:0:0:4630896905707208721: scsi scan: INQUIRY pass 2 length 164
scsi 2:0:0:4630896905707208721: scsi scan: INQUIRY successful with code 0x0
scsi 2:0:0:4630896905707208721: scsi scan: peripheral device type of 31, \
no device added
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Fixes: 9cb78c16f5 ("scsi: use 64-bit LUNs")
Cc: <stable@vger.kernel.org> #3.17+
Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Reviewed-by: Jens Remus <jremus@linux.vnet.ibm.com>
Signed-off-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
At the default trace level, we only trace unsuccessful events including
FSF responses.
zfcp_dbf_hba_fsf_response() only used protocol status and FSF status to
decide on an unsuccessful response. However, this is only one of multiple
possible sources determining a failed struct zfcp_fsf_req.
An FSF request can also "fail" if its response runs into an ERP timeout
or if it gets dismissed because a higher level recovery was triggered
[trace tags "erscf_1" or "erscf_2" in zfcp_erp_strategy_check_fsfreq()].
FSF requests with ERP timeout are:
FSF_QTCB_EXCHANGE_CONFIG_DATA, FSF_QTCB_EXCHANGE_PORT_DATA,
FSF_QTCB_OPEN_PORT_WITH_DID or FSF_QTCB_CLOSE_PORT or
FSF_QTCB_CLOSE_PHYSICAL_PORT for target ports,
FSF_QTCB_OPEN_LUN, FSF_QTCB_CLOSE_LUN.
One example is slow queue processing which can cause follow-on errors,
e.g. FSF_PORT_ALREADY_OPEN after FSF_QTCB_OPEN_PORT_WITH_DID timed out.
In order to see the root cause, we need to see late responses even if the
channel presented them successfully with FSF_PROT_GOOD and FSF_GOOD.
Example trace records formatted with zfcpdbf from the s390-tools package:
Timestamp : ...
Area : REC
Subarea : 00
Level : 1
Exception : -
CPU ID : ..
Caller : ...
Record ID : 1
Tag : fcegpf1
LUN : 0xffffffffffffffff
WWPN : 0x<WWPN>
D_ID : 0x00<D_ID>
Adapter status : 0x5400050b
Port status : 0x41200000
LUN status : 0x00000000
Ready count : 0x00000001
Running count : 0x...
ERP want : 0x02 ZFCP_ERP_ACTION_REOPEN_PORT
ERP need : 0x02 ZFCP_ERP_ACTION_REOPEN_PORT
|
Timestamp : ... 30 seconds later
Area : REC
Subarea : 00
Level : 1
Exception : -
CPU ID : ..
Caller : ...
Record ID : 2
Tag : erscf_2
LUN : 0xffffffffffffffff
WWPN : 0x<WWPN>
D_ID : 0x00<D_ID>
Adapter status : 0x5400050b
Port status : 0x41200000
LUN status : 0x00000000
Request ID : 0x<request_ID>
ERP status : 0x10000000 ZFCP_STATUS_ERP_TIMEDOUT
ERP step : 0x0800 ZFCP_ERP_STEP_PORT_OPENING
ERP action : 0x02 ZFCP_ERP_ACTION_REOPEN_PORT
ERP count : 0x00
|
Timestamp : ... later than previous record
Area : HBA
Subarea : 00
Level : 5 > default level => 3 <= default level
Exception : -
CPU ID : 00
Caller : ...
Record ID : 1
Tag : fs_qtcb => fs_rerr
Request ID : 0x<request_ID>
Request status : 0x00001010 ZFCP_STATUS_FSFREQ_DISMISSED
| ZFCP_STATUS_FSFREQ_CLEANUP
FSF cmnd : 0x00000005
FSF sequence no: 0x...
FSF issued : ... > 30 seconds ago
FSF stat : 0x00000000 FSF_GOOD
FSF stat qual : 00000000 00000000 00000000 00000000
Prot stat : 0x00000001 FSF_PROT_GOOD
Prot stat qual : 00000000 00000000 00000000 00000000
Port handle : 0x...
LUN handle : 0x00000000
QTCB log length: ...
QTCB log info : ...
In case of problems detecting that new responses are waiting on the input
queue, we sooner or later trigger adapter recovery due to an FSF request
timeout (trace tag "fsrth_1").
FSF requests with FSF request timeout are:
typically FSF_QTCB_ABORT_FCP_CMND; but theoretically also
FSF_QTCB_EXCHANGE_CONFIG_DATA or FSF_QTCB_EXCHANGE_PORT_DATA via sysfs,
FSF_QTCB_OPEN_PORT_WITH_DID or FSF_QTCB_CLOSE_PORT for WKA ports,
FSF_QTCB_FCP_CMND for task management function (LUN / target reset).
One or more pending requests can meanwhile have FSF_PROT_GOOD and FSF_GOOD
because the channel filled in the response via DMA into the request's QTCB.
In a theroretical case, inject code can create an erroneous FSF request
on purpose. If data router is enabled, it uses deferred error reporting.
A READ SCSI command can succeed with FSF_PROT_GOOD, FSF_GOOD, and
SAM_STAT_GOOD. But on writing the read data to host memory via DMA,
it can still fail, e.g. if an intentionally wrong scatter list does not
provide enough space. Rather than getting an unsuccessful response,
we get a QDIO activate check which in turn triggers adapter recovery.
One or more pending requests can meanwhile have FSF_PROT_GOOD and FSF_GOOD
because the channel filled in the response via DMA into the request's QTCB.
Example trace records formatted with zfcpdbf from the s390-tools package:
Timestamp : ...
Area : HBA
Subarea : 00
Level : 6 > default level => 3 <= default level
Exception : -
CPU ID : ..
Caller : ...
Record ID : 1
Tag : fs_norm => fs_rerr
Request ID : 0x<request_ID2>
Request status : 0x00001010 ZFCP_STATUS_FSFREQ_DISMISSED
| ZFCP_STATUS_FSFREQ_CLEANUP
FSF cmnd : 0x00000001
FSF sequence no: 0x...
FSF issued : ...
FSF stat : 0x00000000 FSF_GOOD
FSF stat qual : 00000000 00000000 00000000 00000000
Prot stat : 0x00000001 FSF_PROT_GOOD
Prot stat qual : ........ ........ 00000000 00000000
Port handle : 0x...
LUN handle : 0x...
|
Timestamp : ...
Area : SCSI
Subarea : 00
Level : 3
Exception : -
CPU ID : ..
Caller : ...
Record ID : 1
Tag : rsl_err
Request ID : 0x<request_ID2>
SCSI ID : 0x...
SCSI LUN : 0x...
SCSI result : 0x000e0000 DID_TRANSPORT_DISRUPTED
SCSI retries : 0x00
SCSI allowed : 0x05
SCSI scribble : 0x<request_ID2>
SCSI opcode : 28... Read(10)
FCP rsp inf cod: 0x00
FCP rsp IU : 00000000 00000000 00000000 00000000
^^ SAM_STAT_GOOD
00000000 00000000
Only with luck in both above cases, we could see a follow-on trace record
of an unsuccesful event following a successful but late FSF response with
FSF_PROT_GOOD and FSF_GOOD. Typically this was the case for I/O requests
resulting in a SCSI trace record "rsl_err" with DID_TRANSPORT_DISRUPTED
[On ZFCP_STATUS_FSFREQ_DISMISSED, zfcp_fsf_protstatus_eval() sets
ZFCP_STATUS_FSFREQ_ERROR seen by the request handler functions as failure].
However, the reason for this follow-on trace was invisible because the
corresponding HBA trace record was missing at the default trace level
(by default hidden records with tags "fs_norm", "fs_qtcb", or "fs_open").
On adapter recovery, after we had shut down the QDIO queues, we perform
unsuccessful pseudo completions with flag ZFCP_STATUS_FSFREQ_DISMISSED
for each pending FSF request in zfcp_fsf_req_dismiss_all().
In order to find the root cause, we need to see all pseudo responses even
if the channel presented them successfully with FSF_PROT_GOOD and FSF_GOOD.
Therefore, check zfcp_fsf_req.status for ZFCP_STATUS_FSFREQ_DISMISSED
or ZFCP_STATUS_FSFREQ_ERROR and trace with a new tag "fs_rerr".
It does not matter that there are numerous places which set
ZFCP_STATUS_FSFREQ_ERROR after the location where we trace an FSF response
early. These cases are based on protocol status != FSF_PROT_GOOD or
== FSF_PROT_FSF_STATUS_PRESENTED and are thus already traced by default
as trace tag "fs_perr" or "fs_ferr" respectively.
NB: The trace record with tag "fssrh_1" for status read buffers on dismiss
all remains. zfcp_fsf_req_complete() handles this and returns early.
All other FSF request types are handled separately and as described above.
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Fixes: 8a36e4532e ("[SCSI] zfcp: enhancement of zfcp debug features")
Fixes: 2e261af84c ("[SCSI] zfcp: Only collect FSF/HBA debug data for matching trace levels")
Cc: <stable@vger.kernel.org> #2.6.38+
Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If the FCP_RSP UI has optional parts (FCP_SNS_INFO or FCP_RSP_INFO) and
thus does not fit into the fsp_rsp field built into a SCSI trace record,
trace the full FCP_RSP UI with all optional parts as payload record
instead of just FCP_SNS_INFO as payload and
a 1 byte RSP_INFO_CODE part of FCP_RSP_INFO built into the SCSI record.
That way we would also get the full FCP_SNS_INFO in case a
target would ever send more than
min(SCSI_SENSE_BUFFERSIZE==96, ZFCP_DBF_PAY_MAX_REC==256)==96.
The mandatory part of FCP_RSP IU is only 24 bytes.
PAYload costs at least one full PAY record of 256 bytes anyway.
We cap to the hardware response size which is only FSF_FCP_RSP_SIZE==128.
So we can just put the whole FCP_RSP IU with any optional parts into
PAYload similarly as we do for SAN PAY since v4.9 commit aceeffbb59
("zfcp: trace full payload of all SAN records (req,resp,iels)").
This does not cause any additional trace records wasting memory.
Decoded trace records were confusing because they showed a hard-coded
sense data length of 96 even if the FCP_RSP_IU field FCP_SNS_LEN showed
actually less.
Since the same commit, we set pl_len for SAN traces to the full length of a
request/response even if we cap the corresponding trace.
In contrast, here for SCSI traces we set pl_len to the pre-computed
length of FCP_RSP IU considering SNS_LEN or RSP_LEN if valid.
Nonetheless we trace a hardcoded payload of length FSF_FCP_RSP_SIZE==128
if there were optional parts.
This makes it easier for the zfcpdbf tool to format only the relevant
part of the long FCP_RSP UI buffer. And any trailing information is still
available in the payload trace record just in case.
Rename the payload record tag from "fcp_sns" to "fcp_riu" to make the new
content explicit to zfcpdbf which can then pick a suitable field name such
as "FCP rsp IU all:" instead of "Sense info :"
Also, the same zfcpdbf can still be backwards compatible with "fcp_sns".
Old example trace record before this fix, formatted with the tool zfcpdbf
from s390-tools:
Timestamp : ...
Area : SCSI
Subarea : 00
Level : 3
Exception : -
CPU id : ..
Caller : 0x...
Record id : 1
Tag : rsl_err
Request id : 0x<request_id>
SCSI ID : 0x...
SCSI LUN : 0x...
SCSI result : 0x00000002
SCSI retries : 0x00
SCSI allowed : 0x05
SCSI scribble : 0x<request_id>
SCSI opcode : 00000000 00000000 00000000 00000000
FCP rsp inf cod: 0x00
FCP rsp IU : 00000000 00000000 00000202 00000000
^^==FCP_SNS_LEN_VALID
00000020 00000000
^^^^^^^^==FCP_SNS_LEN==32
Sense len : 96 <==min(SCSI_SENSE_BUFFERSIZE,ZFCP_DBF_PAY_MAX_REC)
Sense info : 70000600 00000018 00000000 29000000
00000400 00000000 00000000 00000000
00000000 00000000 00000000 00000000<==superfluous
00000000 00000000 00000000 00000000<==superfluous
00000000 00000000 00000000 00000000<==superfluous
00000000 00000000 00000000 00000000<==superfluous
New example trace records with this fix:
Timestamp : ...
Area : SCSI
Subarea : 00
Level : 3
Exception : -
CPU ID : ..
Caller : 0x...
Record ID : 1
Tag : rsl_err
Request ID : 0x<request_id>
SCSI ID : 0x...
SCSI LUN : 0x...
SCSI result : 0x00000002
SCSI retries : 0x00
SCSI allowed : 0x03
SCSI scribble : 0x<request_id>
SCSI opcode : a30c0112 00000000 02000000 00000000
FCP rsp inf cod: 0x00
FCP rsp IU : 00000000 00000000 00000a02 00000200
00000020 00000000
FCP rsp IU len : 56
FCP rsp IU all : 00000000 00000000 00000a02 00000200
^^=FCP_RESID_UNDER|FCP_SNS_LEN_VALID
00000020 00000000 70000500 00000018
^^^^^^^^==FCP_SNS_LEN
^^^^^^^^^^^^^^^^^
00000000 240000cb 00011100 00000000
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
00000000 00000000
^^^^^^^^^^^^^^^^^==FCP_SNS_INFO
Timestamp : ...
Area : SCSI
Subarea : 00
Level : 1
Exception : -
CPU ID : ..
Caller : 0x...
Record ID : 1
Tag : lr_okay
Request ID : 0x<request_id>
SCSI ID : 0x...
SCSI LUN : 0x...
SCSI result : 0x00000000
SCSI retries : 0x00
SCSI allowed : 0x05
SCSI scribble : 0x<request_id>
SCSI opcode : <CDB of unrelated SCSI command passed to eh handler>
FCP rsp inf cod: 0x00
FCP rsp IU : 00000000 00000000 00000100 00000000
00000000 00000008
FCP rsp IU len : 32
FCP rsp IU all : 00000000 00000000 00000100 00000000
^^==FCP_RSP_LEN_VALID
00000000 00000008 00000000 00000000
^^^^^^^^==FCP_RSP_LEN
^^^^^^^^^^^^^^^^^==FCP_RSP_INFO
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Fixes: 250a1352b9 ("[SCSI] zfcp: Redesign of the debug tracing for SCSI records.")
Cc: <stable@vger.kernel.org> #2.6.38+
Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For problem determination we need to see that we were in scsi_eh
as well as whether and why we were successful or not.
The following commits introduced new early returns without adding
a trace record:
v2.6.35 commit a1dbfddd02
("[SCSI] zfcp: Pass return code from fc_block_scsi_eh to scsi eh")
on fc_block_scsi_eh() returning != 0 which is FAST_IO_FAIL,
v2.6.30 commit 63caf367e1
("[SCSI] zfcp: Improve reliability of SCSI eh handlers in zfcp")
on not having gotten an FSF request after the maximum number of retry
attempts and thus could not issue a TMF and has to return FAILED.
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Fixes: a1dbfddd02 ("[SCSI] zfcp: Pass return code from fc_block_scsi_eh to scsi eh")
Fixes: 63caf367e1 ("[SCSI] zfcp: Improve reliability of SCSI eh handlers in zfcp")
Cc: <stable@vger.kernel.org> #2.6.38+
Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Without this fix we get SCSI trace records on task management functions
which cannot be correlated to HBA trace records because all fields
related to the FSF request are empty (zero).
Also, the FCP_RSP_IU is missing as well as any sense data if available.
This was caused by v2.6.14 commit 8a36e4532e ("[SCSI] zfcp: enhancement
of zfcp debug features") introducing trace records for TMFs but
hard coding NULL for a possibly existing TMF FSF request.
The scsi_cmnd scribble is also zero or unrelated for the TMF request
so it also could not lookup a suitable FSF request from there.
A broken example trace record formatted with zfcpdbf from the s390-tools
package:
Timestamp : ...
Area : SCSI
Subarea : 00
Level : 1
Exception : -
CPU ID : ..
Caller : 0x...
Record ID : 1
Tag : lr_fail
Request ID : 0x0000000000000000
^^^^^^^^^^^^^^^^ no correlation to HBA record
SCSI ID : 0x<scsitarget>
SCSI LUN : 0x<scsilun>
SCSI result : 0x000e0000
SCSI retries : 0x00
SCSI allowed : 0x05
SCSI scribble : 0x0000000000000000
SCSI opcode : 2a000017 3bb80000 08000000 00000000
FCP rsp inf cod: 0x00
^^ no TMF response
FCP rsp IU : 00000000 00000000 00000000 00000000
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
00000000 00000000
^^^^^^^^^^^^^^^^^ no interesting FCP_RSP_IU
Sense len : ...
^^^^^^^^^^^^^^^^^^^^ no sense data length
Sense info : ...
^^^^^^^^^^^^^^^^^^^^ no sense data content, even if present
There are some true cases where we really do not have an FSF request:
"rsl_fai" from zfcp_dbf_scsi_fail_send() called for early
returns / completions in zfcp_scsi_queuecommand(),
"abrt_or", "abrt_bl", "abrt_ru", "abrt_ar" from
zfcp_scsi_eh_abort_handler() where we did not get as far,
"lr_nres", "tr_nres" from zfcp_task_mgmt_function() where we're
successful and do not need to do anything because adapter stopped.
For these cases it's correct to pass NULL for fsf_req to _zfcp_dbf_scsi().
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Fixes: 8a36e4532e ("[SCSI] zfcp: enhancement of zfcp debug features")
Cc: <stable@vger.kernel.org> #2.6.38+
Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
v4.9 commit aceeffbb59 ("zfcp: trace full payload of all SAN records
(req,resp,iels)") fixed trace data loss of 2.6.38 commit 2c55b750a8
("[SCSI] zfcp: Redesign of the debug tracing for SAN records.")
necessary for problem determination, e.g. to see the
currently active zone set during automatic port scan.
While it already saves space by not dumping any empty residual entries
of the large successful GPN_FT response (4 pages), there are seldom cases
where the GPN_FT response is unsuccessful and likely does not have
FC_NS_FID_LAST set in fp_flags so we did not cap the trace record.
We typically see such case for an initiator WWPN, which is not in any zone.
Cap unsuccessful responses to at least the actual basic CT_IU response
plus whatever fits the SAN trace record built-in "payload" buffer
just in case there's trailing information
of which we would at least see the existence and its beginning.
In order not to erroneously cap successful responses, we need to swap
calling the trace function and setting the CT / ELS status to success (0).
Example trace record pair formatted with zfcpdbf:
Timestamp : ...
Area : SAN
Subarea : 00
Level : 1
Exception : -
CPU ID : ..
Caller : 0x...
Record ID : 1
Tag : fssct_1
Request ID : 0x<request_id>
Destination ID : 0x00fffffc
SAN req short : 01000000 fc020000 01720ffc 00000000
00000008
SAN req length : 20
|
Timestamp : ...
Area : SAN
Subarea : 00
Level : 1
Exception : -
CPU ID : ..
Caller : 0x...
Record ID : 2
Tag : fsscth2
Request ID : 0x<request_id>
Destination ID : 0x00fffffc
SAN resp short : 01000000 fc020000 80010000 00090700
00000000 00000000 00000000 00000000 [trailing info]
00000000 00000000 00000000 00000000 [trailing info]
SAN resp length: 16384
San resp info : 01000000 fc020000 80010000 00090700
00000000 00000000 00000000 00000000 [trailing info]
00000000 00000000 00000000 00000000 [trailing info]
00000000 00000000 00000000 00000000 [trailing info]
00000000 00000000 00000000 00000000 [trailing info]
00000000 00000000 00000000 00000000 [trailing info]
00000000 00000000 00000000 00000000 [trailing info]
00000000 00000000 00000000 00000000 [trailing info]
00000000 00000000 00000000 00000000 [trailing info]
00000000 00000000 00000000 00000000 [trailing info]
00000000 00000000 00000000 00000000 [trailing info]
00000000 00000000 00000000 00000000 [trailing info]
00000000 00000000 00000000 00000000 [trailing info]
00000000 00000000 00000000 00000000 [trailing info]
00000000 00000000 00000000 00000000 [trailing info]
00000000 00000000 00000000 00000000 [trailing info]
The fix saves all but one of the previously associated 64 PAYload trace
record chunks of size 256 bytes each.
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Fixes: aceeffbb59 ("zfcp: trace full payload of all SAN records (req,resp,iels)")
Fixes: 2c55b750a8 ("[SCSI] zfcp: Redesign of the debug tracing for SAN records.")
Cc: <stable@vger.kernel.org> #2.6.38+
Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Up until now zfcp would just ignore the FCP_RESID_OVER flag in the FCP
response IU. When this flag is set, it is possible, in regards to the
FCP standard, that the storage-server processes the command normally, up
to the point where data is missing and simply ignores those.
In this case no CHECK CONDITION would be set, and because we ignored the
FCP_RESID_OVER flag we resulted in at least a data loss or even
-corruption as a follow-up error, depending on how the
applications/layers on top behave. To prevent this, we now set the
host-byte of the corresponding scsi_cmnd to DID_ERROR.
Other storage-behaviors, where the same condition results in a CHECK
CONDITION set in the answer, don't need to be changed as they are
handled in the mid-layer already.
Following is an example trace record decoded with zfcpdbf from the
s390-tools package. We forcefully injected a fc_dl which is one byte too
small:
Timestamp : ...
Area : SCSI
Subarea : 00
Level : 3
Exception : -
CPU ID : ..
Caller : 0x...
Record ID : 1
Tag : rsl_err
Request ID : 0x...
SCSI ID : 0x...
SCSI LUN : 0x...
SCSI result : 0x00070000
^^DID_ERROR
SCSI retries : 0x..
SCSI allowed : 0x..
SCSI scribble : 0x...
SCSI opcode : 2a000000 00000000 08000000 00000000
FCP rsp inf cod: 0x00
FCP rsp IU : 00000000 00000000 00000400 00000001
^^fr_flags==FCP_RESID_OVER
^^fr_status==SAM_STAT_GOOD
^^^^^^^^fr_resid
00000000 00000000
As of now, we don't actively handle to possibility that a response IU
has both flags - FCP_RESID_OVER and FCP_RESID_UNDER - set at once.
Reported-by: Luke M. Hopkins <lmhopkin@us.ibm.com>
Reviewed-by: Steffen Maier <maier@linux.vnet.ibm.com>
Fixes: 553448f6c4 ("[SCSI] zfcp: Message cleanup")
Fixes: ea127f975424 ("[PATCH] s390 (7/7): zfcp host adapter.") (tglx/history.git)
Cc: <stable@vger.kernel.org> #2.6.33+
Signed-off-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since commit db007fc5e2 ("[SCSI] Command protection operation"),
scsi_eh_prep_cmnd() saves scmd->prot_op and temporarily resets it to
SCSI_PROT_NORMAL.
Other FCP LLDDs such as qla2xxx and lpfc shield their queuecommand()
to only access any of scsi_prot_sg...() if
(scsi_get_prot_op(cmd) != SCSI_PROT_NORMAL).
Do the same thing for zfcp, which introduced DIX support with
commit ef3eb71d8b ("[SCSI] zfcp: Introduce experimental support for
DIF/DIX").
Otherwise, TUR SCSI commands as part of scsi_eh likely fail in zfcp,
because the regular SCSI command with DIX protection data, that scsi_eh
re-uses in scsi_send_eh_cmnd(), of course still has
(scsi_prot_sg_count() != 0) and so zfcp sends down bogus requests to the
FCP channel hardware.
This causes scsi_eh_test_devices() to have (finish_cmds == 0)
[not SCSI device is online or not scsi_eh_tur() failed]
so regular SCSI commands, that caused / were affected by scsi_eh,
are moved to work_q and scsi_eh_test_devices() itself returns false.
In turn, it unnecessarily escalates in our case in scsi_eh_ready_devs()
beyond host reset to finally scsi_eh_offline_sdevs()
which sets affected SCSI devices offline with the following kernel message:
"kernel: sd H:0:T:L: Device offlined - not ready after error recovery"
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Fixes: ef3eb71d8b ("[SCSI] zfcp: Introduce experimental support for DIF/DIX")
Cc: <stable@vger.kernel.org> #2.6.36+
Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Better form and cleans remaining warnings.
Found with scripts/coccinelle/misc/boolinit.cocci.
Signed-off-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
drivers/s390/scsi/zfcp_aux.c does not contain any miscdevice so the
inclusion of linux/miscdevice.h is unnecessary.
[maier@linux.vnet.ibm.com: just for the records, this is in fact a
minor missing code cleanup of the following older "feature"
which also dropped the only former use of a misc device in zfcp:
commit 663e0890e3 ("[SCSI] zfcp: remove access control tables
interface")
commit b5dc3c4800 ("[SCSI] zfcp: remove access control tables
interface (keep sysfs files)")
commit 1b33ef2394 ("zfcp: remove access control tables interface
(port leftovers)")]
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use initialization with setup_timer function instead of using
init_timer function and data fields. It improves readability.
Signed-off-by: Lukáš Korenčik <xkorenc1@fi.muni.cz>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The zfcp_qdio_sbale_count function do the same work than sg_nents().
So replace it by sg_nents() for removing duplicate code.
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Signed-off-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since commit caf7df1227 ("block: remove the errors field from struct request")
rq->errors can't be (mis)used by block device drivers to store the error
condition for usage during async completion. Because of that I simply used
async completion only for the non-error paths.
This patch places the error within the private data of struct request and
uses async completion for all paths again.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
vmcp_ioctl() has many different return statements and duplicates a lot
of mutex_unlock() calls. Simplify this so that only one return
statement and one mutex_unlock() call is left.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Return -ENOTTY for unknown ioctl commands instead of
-ENOIOCTLCMD. This isn't that much of difference, since common code
will translate -ENOIOCTLCMD to -ENOTTY anyway, but this way it seems
to be more obvious what is happening (at least to me).
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Split the vmcp header file and move the device driver internal
structure to the C file, and move the ioctl definitions to the uapi
directory.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If memory is fragmented it is unlikely that large order memory
allocations succeed. This has been an issue with the vmcp device
driver since a long time, since it requires large physical contiguous
memory ares for large responses.
To hopefully resolve this issue make use of the contiguous memory
allocator (cma). This patch adds a vmcp specific vmcp cma area with a
default size of 4MB. The size can be changed either via the
VMCP_CMA_SIZE config option at compile time or with the "vmcp_cma"
kernel parameter (e.g. "vmcp_cma=16m").
For any vmcp response buffers larger than 16k memory from the cma area
will be allocated. If such an allocation fails, there is a fallback to
the buddy allocator.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
According to the CP Programming Services manual Diagnose Code 8
"Virtual Console Function" can be used in all addressing modes. Also
the input and output buffers do not have a limitation which specifies
they need to be below the 2GB line.
This is true at least since z/VM 5.4.
Therefore remove the sam31/64 instructions and allow for simple
GFP_KERNEL allocations. This makes it easier to allocate a 1MB page
if the user requested such a large return buffer.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The vmcp device driver should return -EFAULT if get_user() fails, due
to an invalid user space address. In addition the buffer size value
from user space is passed unchecked to get_order(). The return value
of get_order(0) undefined.
Therefore explicitly test for zero before calling get_order() and also
return -EFAULT if get_user() fails.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
On L3, the qeth_hdr struct needs to be filled with the next-hop
IP address.
The current code accesses rtable->rt_gateway without checking that
rtable is a valid address. The accidental access to a lowcore area
results in a random next-hop address in the qeth_hdr.
rtable (or more precisely, skb_dst(skb)) can be NULL in rare cases
(for instance together with AF_PACKET sockets).
This patch adds the missing NULL-ptr checks.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Fixes: 87e7597b5a qeth: Move away from using neighbour entries in qeth_l3_fill_header()
Signed-off-by: David S. Miller <davem@davemloft.net>
Add const to bin_attribute structures as they are only passed to the
functions device_{remove/create}_bin_file. The corresponding arguments
are of type const, so declare the structures to be const.
Cross compiled for s390 architecture.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Declare bin_attribute structure as const as it is only passed as an
argument to the function sysfs_create_bin_file. This argument is of
type const, so declare the structure as const.
Cross compiled for s390 architecture.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
-----BEGIN PGP SIGNATURE-----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=CQfQ
-----END PGP SIGNATURE-----
Merge tag 'vfio-ccw-20170724' of git://git.kernel.org/pub/scm/linux/kernel/git/kvms390/vfio-ccw into features
Pull vfio-ccw fix from Cornelia Huck:
"A bugfix in the ccw translation code."
attribute_group are not supposed to change at runtime. All functions
working with attribute_group provided by <linux/sysfs.h> work
with const attribute_group. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
attribute_group are not supposed to change at runtime. All functions
working with attribute_group provided by <linux/sysfs.h> work
with const attribute_group. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
11511 656 16 12183 2f97 drivers/s390/char/tape_core.o
File size After adding 'const':
text data bss dec hex filename
11575 592 16 12183 2f97 drivers/s390/char/tape_core.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
attribute_group are not supposed to change at runtime. All functions
working with attribute_group provided by <linux/sysfs.h> work
with const attribute_group. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
8069 816 16 8901 22c5 drivers/s390/char/raw3270.o
File size After adding 'const':
text data bss dec hex filename
8133 752 16 8901 22c5 drivers/s390/char/raw3270.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
attribute_group are not supposed to change at runtime. All functions
working with attribute_group provided by <linux/sysfs.h> work
with const attribute_group. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
6763 1216 0 7979 1f2b drivers/s390/net/qeth_l3_sys.o
File size After adding 'const':
text data bss dec hex filename
7019 960 0 7971 1f2b drivers/s390/net/qeth_l3_sys.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
attribute_group are not supposed to change at runtime. All functions
working with attribute_group provided by <linux/sysfs.h> work
with const attribute_group. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
attribute_group are not supposed to change at runtime. All functions
working with attribute_group provided by <linux/sysfs.h> work
with const attribute_group. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
attribute_group are not supposed to change at runtime. All functions
working with attribute_group provided by <linux/sysfs.h> work
with const attribute_group. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
1019 160 0 1179 49b drivers/s390/crypto/zcrypt_card.o
File size After adding 'const':
text data bss dec hex filename
1083 96 0 1179 49b drivers/s390/crypto/zcrypt_card.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
attribute_group are not supposed to change at runtime. All functions
working with attribute_group provided by <linux/sysfs.h> work
with const attribute_group. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
1361 96 0 1457 5b1 s390/crypto/zcrypt_queue.o
File size After adding 'const':
text data bss dec hex filename
1425 32 0 1457 5b1 s390/crypto/zcrypt_queue.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Pull s390 fixes from Martin Schwidefsky:
"Three bug fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/mm: set change and reference bit on lazy key enablement
s390: chp: handle CRW_ERC_INIT for channel-path status change
s390/perf: fix problem state detection
When we are translating channel data addresses from guest to host
address space for TIC instructions we are getting incorrect
addresses because of a pointer arithmetic error.
We currently calculate the offset of the TIC's cda from the start
of the channel program chain (ccw->cda - ccw_head). We then add
that to the address of the ccw chain in host memory (iter->ch_ccw).
The problem is that iter->ch_ccw is a pointer to struct ccw1 so
when we increment it we are actually incrementing by the size of
struct ccw1 which is 8 bytes. The intent was to increment by
n-bytes, not n*8.
The fix: cast iter->ch_ccw to char* so it will be incremented by
n*1.
Reviewed-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Signed-off-by: Jason J. Herne <jjherne@linux.vnet.ibm.com>
Signed-off-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Message-Id: <20170721011436.76112-1-bjsdjshi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Harald Freudenberger