A common pattern with skb_put() is to just want to memcpy()
some data into the new space, introduce skb_put_data() for
this.
An spatch similar to the one for skb_put_zero() converts many
of the places using it:
@@
identifier p, p2;
expression len, skb, data;
type t, t2;
@@
(
-p = skb_put(skb, len);
+p = skb_put_data(skb, data, len);
|
-p = (t)skb_put(skb, len);
+p = skb_put_data(skb, data, len);
)
(
p2 = (t2)p;
-memcpy(p2, data, len);
|
-memcpy(p, data, len);
)
@@
type t, t2;
identifier p, p2;
expression skb, data;
@@
t *p;
...
(
-p = skb_put(skb, sizeof(t));
+p = skb_put_data(skb, data, sizeof(t));
|
-p = (t *)skb_put(skb, sizeof(t));
+p = skb_put_data(skb, data, sizeof(t));
)
(
p2 = (t2)p;
-memcpy(p2, data, sizeof(*p));
|
-memcpy(p, data, sizeof(*p));
)
@@
expression skb, len, data;
@@
-memcpy(skb_put(skb, len), data, len);
+skb_put_data(skb, data, len);
(again, manually post-processed to retain some comments)
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the HCI User Channel access is requested, then do not try to
undermine it with vendor diagnostic configuration. The exclusive user
is required to configure its own vendor diagnostic in that case and
can not rely on the host stack support.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
If the LE Set Default PHY command is supported, the indicate to the
controller that the host has no preferences for transmitter PHY or
receiver PHY selection.
Issuing this command gives the controller a clear indication that other
PHY can be selected if available.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
If either LE Set Default PHY command or LE Set PHY commands is
supported, then enable the LE PHY Update Complete event.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
If the Channel Selection Algorithm #2 feature is supported, then enable
the new LE Channel Selection Algorithm event.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Use the initial connection interval recommended in Bluetooth
Specification v4.2 (30ms - 50ms).
Signed-off-by: Jonas Holmberg <jonashg@axis.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When closing HCI User Channel, the New Settings event was send out to
inform about changed settings. However such event is wrong since the
exclusive HCI User Channel access is active until the Index Added event
has been sent.
@ USER Close: test
@ MGMT Event: New Settings (0x0006) plen 4
Current settings: 0x00000ad0
Bondable
Secure Simple Pairing
BR/EDR
Low Energy
Secure Connections
= Close Index: 00:14:EF:22:04:12
@ MGMT Event: Index Added (0x0004) plen 0
Calling __mgmt_power_off from hci_dev_do_close requires an extra check
for an active HCI User Channel.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Some Bluetooth controllers allow for reading hardware and firmware
related vendor specific infos. If they are available, then they can be
exposed via debugfs now.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The HCI_BREDR naming is confusing since it actually stands for Primary
Bluetooth Controller. Which is a term that has been used in the latest
standard. However from a legacy point of view there only really have
been Basic Rate (BR) and Enhanced Data Rate (EDR). Recent versions of
Bluetooth introduced Low Energy (LE) and made this terminology a little
bit confused since Dual Mode Controllers include BR/EDR and LE. To
simplify this the name HCI_PRIMARY stands for the Primary Controller
which can be a single mode or dual mode controller.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
With all the latest fixes applied, I am still able to reproduce this
(and other) warning(s):
WARNING: CPU: 1 PID: 19684 at ../kernel/workqueue.c:4092 destroy_workqueue+0x70a/0x770()
...
Call Trace:
[<ffffffff819fee81>] ? dump_stack+0xb3/0x112
[<ffffffff8117377e>] ? warn_slowpath_common+0xde/0x140
[<ffffffff811ce68a>] ? destroy_workqueue+0x70a/0x770
[<ffffffff811739ae>] ? warn_slowpath_null+0x2e/0x40
[<ffffffff811ce68a>] ? destroy_workqueue+0x70a/0x770
[<ffffffffa0c944c9>] ? hci_unregister_dev+0x2a9/0x720 [bluetooth]
[<ffffffffa0b301db>] ? vhci_release+0x7b/0xf0 [hci_vhci]
[<ffffffffa0b30160>] ? vhci_flush+0x50/0x50 [hci_vhci]
[<ffffffff8117cd73>] ? do_exit+0x863/0x2b90
This is due to race present in the hci_unregister_dev path.
hdev->power_on work races with hci_dev_do_close. One tries to open,
the other tries to close, leading to warning like the above. (Another
example is a warning in kobject_get or kobject_put depending on who
wins the race.)
Fix this by switching those two racers to ensure hdev->power_on never
triggers while hci_dev_do_close is in progress.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When the HCI_AUTO_OFF flag is cleared, the power_off delayed work need
to be cancel or HCI will be powered off even if it's managed.
Signed-off-by: Wei-Ning Huang <wnhuang@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Recently a managed version of led_trigger_register was introduced.
Using devm_led_trigger_register allows to simplify the LED trigger code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add support for LED triggers to the Bluetooth subsystem and add kernel
config symbol BT_LEDS for it.
For now one trigger for indicating "HCI is powered up" is supported.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In commit 44d2713774 ("Bluetooth: Compress the size of struct
hci_ctrl") we squashed down the size of the structure by using a union
with the assumption that all users would use the flag to determine
whether we had a req_complete or a req_complete_skb.
Unfortunately we had a case in hci_req_cmd_complete() where we weren't
looking at the flag. This can result in a situation where we might be
storing a hci_req_complete_skb_t in a hci_req_complete_t variable, or
vice versa.
During some testing I found at least one case where the function
hci_req_sync_complete() was called improperly because the kernel thought
that it didn't require an SKB. Looking through the stack in kgdb I
found that it was called by hci_event_packet() and that
hci_event_packet() had both of its locals "req_complete" and
"req_complete_skb" pointing to the same place: both to
hci_req_sync_complete().
Let's make sure we always check the flag.
For more details on debugging done, see <http://crbug.com/588288>.
Fixes: 44d2713774 ("Bluetooth: Compress the size of struct hci_ctrl")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Use list_for_each_entry*() instead of list_for_each*() to simplify
the code.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We can simplify a lot of code by making sure hdev->cur_adv_instance is
always up-to-date. This allows e.g. the removal of the
get_current_adv_instance() helper function and the special
HCI_ADV_CURRENT value. This patch also makes selecting instance 0x00
explicit in the various calls where advertising instances aren't
enabled, e.g. when HCI_ADVERTISING is set or we've just finished
enabling LE.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The request to update HCI during power on is always coming either from
hdev->req_workqueue or through an ioctl, so it's safe to use
hci_req_sync for it. This way we also eliminate potential races with
incoming mgmt commands or other actions while powering on.
Part of this refactoring is the splitting of mgmt_powered() into
mgmt_power_on() and __mgmt_power_off() functions. The main reason is
the different requirements as far as hdev locking is concerned, as
highlighted with the __ prefix of the power off API.
Since the power on in the case of clearing the AUTO_OFF flag cannot be
done synchronously in the set_powered mgmt handler, the hci_power_on
work callback is extended to cover this (which also simplifies the
set_powered helper a lot).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since the other discoverable changes are behind req_workqueue now it
only makes sense to move the discoverable timeout there as well.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This paves the way for eventually performing advertising changes
through the hdev->req_workqueue. Some new APIs need to be exposed from
mgmt.c to hci_request.c and vice-versa, but many of them will go away
once hdev->req_workqueue gets used.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Fix errors reported by checkpatch.
- ERROR: spaces required around that ':' (ctx:VxW)
- ERROR: open brace '{' following function declarations go on the next line
Signed-off-by: Prasanna Karthik <mkarthi3@visteon.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The hci_req_sync_cancel() is just as much related to the request
cleanup as hci_request_cancel_all() is. Just move the former into the
latter and do the cleanup from a single place in hci_dev_do_close().
The important thing is to avoid deadlocks by holding the req_sync
lock: previously hci_request_cancel_all was done right after releasing
the lock and with this patch it's right before taking it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In some circumstances it may be useful to abort the request through
checks done in the request callback. To make the feature possible this
patch changes the return value of the request callback from void to
int and aborts the request if a non-zero value is returned.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To avoid any risks of races, place also these LE scan modification
work callbacks behind the same work queue as the other LE scan
changes.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In some cases it may be important to get the exact HCI status rather
than the converted HCI-to-errno value. Add an optional return
parameter to the hci_req_sync() API to allow for this. Since there are
no good HCI translation candidates for cancelation and timeout, use
the "unknown" status code for those cases.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Prepare hci_request.c to have code for doing synchronous HCI requests,
such as LE scanning or advertising changes. The necessary work
callbacks will be set up in hci_request_setup() and cleaned up in
hci_request_cancel_all(). The former is used when an HCI device get
registered, and the latter each time it is powered off (or
unregistered).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To make it clear which HCI request APIs target specifically
synchronous requests, add 'sync' to the API names.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
hci_request.c is a more natural place for the synchronous request
handling. Furthermore, we will soon need access to some of the
previously private-to-hci_core.c functions from hci_request.c.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The hci_conn_params_clear_all() function is only called from
hci_unregister_dev() at which point it's completely futile to try to
do any LE scanning updates. Simply remove this unnecessary function
call. At the same time we can make the function static since it's only
accessed from within the same c-file.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We can reduce the size of the hci_ctrl struct by converting
'bool req_start' to 'u8 req_flags' and making the two function
pointers a union (since only one is ever set at a time).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The new hci_skb_pkt_* wrappers only help if they are used consistently
in the Bluetooth subsystem. So first convert the core packet handling.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
For the LE only controllers, there are events that should not be enabled
if the corresponding command is not supported.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When setting the event mask, the HCI_QUIRK_FIXUP_INQUIRY_MODE quirk is
required to be checked so that the Inquiry Result with RSSI event gets
actually enabled.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The LE event mask should be created based on the commands that are
actually supported by the controller.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
There are some BR/EDR default events for Bluetooth 1.2 or later
controllers that are not conditional on their features being present.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The white list commands might not be implemented if the controller does
not actually support the white list. So check the supported commands
first before issuing these commands. Not supporting the white list is
the same as supporting a white list with zero size.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
There is no point in wrapping hci_sock_dev_event around hci_notify. It
is an empty wrapper which adds no value. So remove it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The SKB context buffer for HCI request is really not just for requests,
information in their are preserved for the whole HCI layer. So it makes
more sense to actually rename it into bt_cb()->hci and also call it then
struct hci_ctrl.
In addition that allows moving the decoded opcode for outgoing packets
into that struct. So far it was just consuming valuable space from the
main shared items. And opcode are not valid for L2CAP packets.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
There's only one user of this helper which can be replaces with a call
to hci_pend_le_action_lookup() and a check for params->explicit_connect.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Some drivers might have to restore certain settings after the init
procedure has been completed. This driver callback allows them to hook
into that stage. This callback is run just before the controller is
declared as powered up.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Before the vendor specific setup stage is triggered call back into the
core to trigger an internal notification event. That event is used to
send an index update to the monitor interface. With that specific event
it is possible to update userspace with manufacturer information before
any HCI command has been executed. This is useful for early stage
debugging of vendor specific initialization sequences.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
If the diagnostic settings are not persistent over HCI Reset, then this
quirk can be used to tell the Bluetoth core about it. This will ensure
that the settings are programmed correctly when the controller is
powered up.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Sending diagnostic messages directly to the monitor socket might cause
issues for devices processing their messages in interrupt context. So
instead of trying to directly forward them, queue them up with the other
HCI packets and lets them be processed by the sockets at the same time.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Conflicts:
drivers/net/usb/asix_common.c
net/ipv4/inet_connection_sock.c
net/switchdev/switchdev.c
In the inet_connection_sock.c case the request socket hashing scheme
is completely different in net-next.
The other two conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
We can't use hci_explicit_connect_lookup() since that would only cover
explicit connections, leaving normal reconnections completely
untouched. Not using it in turn means leaving out entries in
pend_le_reports.
To fix this and simplify the logic move conn params from the reports
list to the pend_le_conns list for the duration of an explicit
connect. Once the connect is complete move the params back to the
pend_le_reports list. This also means that the explicit connect lookup
function only needs to look into the pend_le_conns list.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When the controller is unconfigured (for example it does not have a
valid Bluetooth address), then the basic debugfs entries for dut_mode
and vendor_diag are not creates. Ensure they are created in __hci_init
and also __hci_unconf_init functions. One of them is called during setup
stage of a new controller.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When calling the hci_recv_frame driver function check for valid packet
types that the core should process. This should catch issues with
drivers trying to feed vendor packet types through this interface.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When the controller requires the HCI Reset command to be send when
closing the transport, the HCI_AUTO_OFF needs to be accounted for. The
current code tries to actually do that, but the flag gets cleared to
early. So store its value and use it that stored value instead of
checking for a flag that is always cleared.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Tejun Heo