Add a converter to retrieve NAND timings from an ONFI NAND timing mode.
At the moment, only SDR NAND timings are supported.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Define a struct containing the standard NAND timings as described in NAND
datasheets.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Some new Micron flash chips require reading the flag status register to
determine when operations have completed.
Furthermore, chips with multi-die stacks of the 65nm 256Mb QSPI also
require reading the status register before reading the flag status
register.
This patch adds support for the flag status register in the n25q512ax3
and n25q00 Micron QSPI flash chips.
Signed-off-by: Graham Moore <grmoore@altera.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
In addition to mtd_block_isbad(), which checks if a block is bad or
reserved, it's needed to check if a block is reserved only (but not
bad). This commit adds an MTD interface for it, in a similar fashion to
mtd_block_isbad().
While here, fix mtd_block_isbad() so the out-of-bounds checking is done
before the callback check.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
- refactor m25p80.c driver for use as a general SPI NOR framework for other
drivers which may speak to SPI NOR flash without providing full SPI support
(i.e., not part of drivers/spi/)
- new Freescale QuadSPI driver (utilizing new SPI NOR framework)
- updates for the STMicro "FSM" SPI NOR driver
- fix sync/flush behavior on mtd_blkdevs
- fixup subpage write support on a few NAND drivers
- correct the MTD OOB test for odd-sized OOB areas
- add BCH-16 support for OMAP NAND
- fix warnings and trivial refactoring
- utilize new ECC DT bindings in pxa3xx NAND driver
- new LPDDR NVM driver
- address a few assorted bugs caught by Coverity
- add new imx6sx support for GPMI NAND
- use a bounce buffer for NAND when non-DMA-able buffers are used
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=6UIq
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20140610' of git://git.infradead.org/linux-mtd
Pull MTD updates from Brian Norris:
- refactor m25p80.c driver for use as a general SPI NOR framework for
other drivers which may speak to SPI NOR flash without providing full
SPI support (i.e., not part of drivers/spi/)
- new Freescale QuadSPI driver (utilizing new SPI NOR framework)
- updates for the STMicro "FSM" SPI NOR driver
- fix sync/flush behavior on mtd_blkdevs
- fixup subpage write support on a few NAND drivers
- correct the MTD OOB test for odd-sized OOB areas
- add BCH-16 support for OMAP NAND
- fix warnings and trivial refactoring
- utilize new ECC DT bindings in pxa3xx NAND driver
- new LPDDR NVM driver
- address a few assorted bugs caught by Coverity
- add new imx6sx support for GPMI NAND
- use a bounce buffer for NAND when non-DMA-able buffers are used
* tag 'for-linus-20140610' of git://git.infradead.org/linux-mtd: (77 commits)
mtd: gpmi: add gpmi support for imx6sx
mtd: maps: remove check for CONFIG_MTD_SUPERH_RESERVE
mtd: bf5xx_nand: use the managed version of kzalloc
mtd: pxa3xx_nand: make the driver work on big-endian systems
mtd: nand: omap: fix omap_calculate_ecc_bch() for-loop error
mtd: nand: r852: correct write_buf loop bounds
mtd: nand_bbt: handle error case for nand_create_badblock_pattern()
mtd: nand_bbt: remove unused variable
mtd: maps: sc520cdp: fix warnings
mtd: slram: fix unused variable warning
mtd: pfow: remove unused variable
mtd: lpddr: fix Kconfig dependency, for I/O accessors
mtd: nand: pxa3xx: Add supported ECC strength and step size to the DT binding
mtd: nand: pxa3xx: Use ECC strength and step size devicetree binding
mtd: nand: pxa3xx: Clean pxa_ecc_init() error handling
mtd: nand: Warn the user if the selected ECC strength is too weak
mtd: nand: omap: Documentation: How to select correct ECC scheme for your device ?
mtd: nand: omap: add support for BCH16_ECC - NAND driver updates
mtd: nand: omap: add support for BCH16_ECC - ELM driver updates
mtd: nand: omap: add support for BCH16_ECC - GPMC driver updates
...
Fixes warning:
In file included from drivers/mtd/lpddr/qinfo_probe.c:31:0:
include/linux/mtd/pfow.h: In function ‘send_pfow_command’:
include/linux/mtd/pfow.h:104:6: warning: variable ‘chipnum’ set but not used [-Wunused-but-set-variable]
int chipnum;
^
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
nand_base can be passed a kmap()'d buffers from highmem by
filesystems like jffs2. This results in failure to map the
physical address of the DMA buffer on various contoller
driver on different platforms. This change adds a chip option
to use preallocated databuf as bounce buffers used in
nand_do_read_ops() and nand_do_write_ops().
This allows for specific nand controller driver to set this
option as needed.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The nand_chip::erase_cmd callback previously served a dual purpose; for
one, it allowed a per-flash-chip override, so that AG-AND devices could
use a different erase command than other NAND. These AND devices were
dropped in commit 14c6578683 (mtd: nand:
remove AG-AND support). On the other hand, some drivers (denali and
doc-g4) need to use this sort of callback to implement
controller-specific erase operations.
To make the latter operation easier for some drivers (e.g., ST's new BCH
NAND driver), it helps if the command dispatch and wait functions can be
lumped together, rather than called separately.
This patch does two things:
1. Pull the call to chip->waitfunc() into chip->erase_cmd(), and return
the status from this callback
2. Rename erase_cmd() to just erase(), since this callback does a
little more than just send a command
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Tested-by: Lee Jones <lee.jones@linaro.org>
shiraz.hashim@st.com email-id doesn't exist anymore as he has left the
company. Replace ST's id with shiraz.linux.kernel@gmail.com.
It also updates .mailmap file to fix address for 'git shortlog'.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Shiraz Hashim <shiraz.linux.kernel@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
serial_flash_cmds.h defines our opcodes a little differently. Let's
borrow its naming, since it's borrowed from the SFDP standard, and it's
more extensible.
This prepares us for merging serial_flash_cmds.h and spi-nor.h opcode
listing.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Huang Shijie <b32955@freescale.com>
Qualify these with a better namespace, and prepare them for use in more
drivers.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Huang Shijie <b32955@freescale.com>
Spacing is a little non-standard here. Fix up tabs vs. spaces.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Huang Shijie <b32955@freescale.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Add the copyright information for spi-nor.c and spi-nor.h.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add the spi_nor_match_id() to find the proper spi_device_id with the
NOR flash's name in the spi_nor_ids table.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This patch cloned most of the m25p80.c. In theory, it adds a new spi-nor layer.
Before this patch, the layer is like:
MTD
------------------------
m25p80
------------------------
spi bus driver
------------------------
SPI NOR chip
After this patch, the layer is like:
MTD
------------------------
spi-nor
------------------------
m25p80
------------------------
spi bus driver
------------------------
SPI NOR chip
With the spi-nor controller driver(Freescale Quadspi), it looks like:
MTD
------------------------
spi-nor
------------------------
fsl-quadspi
------------------------
SPI NOR chip
New APIs:
spi_nor_scan: used to scan a spi-nor flash.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
[Brian: rebased to include additional m25p_ids[] entry]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The spi_nor{} is cloned from the m25p{}.
The spi_nor{} can be used by both the m25p80 and spi-nor controller.
We also add the spi_nor_xfer_cfg{} which can be used by the two
fundamental primitives: read_xfer/write_xfer.
1) the hooks for spi_nor{}:
@prepare/unpreare: used to do some work before or after the
read/write/erase/lock/unlock.
@read_xfer/write_xfer: We can use these two hooks to code all
the following hooks if the driver tries to implement them
by itself.
@read_reg: used to read the registers, such as read status register,
read configure register.
@write_reg: used to write the registers, such as write enable,
erase sector.
@read_id: read out the ID info.
@wait_till_ready: wait till the NOR becomes ready.
@read: read out the data from the NOR.
@write: write data to the NOR.
@erase: erase a sector of the NOR.
2) Add a new field sst_write_second for the SST NOR write.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This patch adds a new header :spi-nor.h,
and copies all the SPI NOR commands and relative macros into this new header.
This hearder can be used by the m25p80.c and other spi-nor controller,
such as Freescale's Quadspi.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
GET_FEATURES and SET_FEATURES also need byte-addressing on 16-bit devices.
Signed-off-by: David Mosberger <davidm@egauge.net>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add the "page" argument for the read_subpage hook. With this argument,
the implementation of this hook could prints out more accurate information
for debugging.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This patch adds the parsing code for the JEDEC compliant NAND.
Since we need the 0x40 as the column address, this patch also
makes the NAND_CMD_PARAM to use the 8-bit address only.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add a helper to get the supported features for JEDEC compliant NAND.
Also add a macro JEDEC_FEATURE_16_BIT_BUS.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add the jedec_version field, and add an anonymous union which
contains the nand_onfi_params and nand_jedec_params.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Create the nand_jedec_params{} and jedec_ecc_info{} according to
the JESD230A (Revision of JESD230, October 2012).
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The NAND command helpers tend to automatically shift the column address
for x16 bus devices, since most commands expect a word address, not a
byte address. The Read ID command, however, expects an 8-bit address
(i.e., 0x00, 0x20, or 0x40 should not be translated to 0x00, 0x10, or
0x20).
This fixes the column address for a few drivers which imitate the
nand_base defaults. Note that I don't touch sh_flctl.c, since it already
handles this problem slightly differently (note its comment "READID is
always performed using an 8-bit bus").
I have not tested this patch, as I only have x8 parts up for testing at
this point. Hopefully that can change soon...
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-By: Pekon Gupta <pekon@ti.com>
There is no reference to these two macros now.
Just remove them.
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The patch converts the arrays to buffer pointers for nand_buffers{}.
The cafe_nand.c is the only NAND_OWN_BUFFERS user which allocates
nand_buffers{} itself.
This patch disables the DMA for nand_scan_ident, and restores the DMA
status after we finish the nand_scan_ident. This way, we can get page
size and OOB size and use them to allocate cafe->dmabuf.
Since the cafe_nand.c uses the NAND_ECC_HW_SYNDROME ECC mode, we do not
allocate the buffers for @ecccalc and @ecccode.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
mtdram_init_device() wasn't updated along with mtd_partition.name.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Add the Intel manufacturer Id.
Tested with Intel JS29F32G08ACMD1(4096 + 224) which is ONFI 2.0 compliant
nand.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add the manufactor ID for SanDisk.
Make preparation for SanDisk SDTNRGAMA-008G.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
According to the Open NAND Flash Interface Specification (ONFI) Revision
3.1 "Parameters are always transferred on the lower 8-bits of the data
bus." for the Get Features and Set Features commands.
So using read_buf and write_buf is wrong for 16-bit wide nand chips as
they use I/O[15:0]. The Get Features command is easily fixed using 4
times the read_byte callback. For Set Features implement a new
overwritable callback "write_byte". Still I expect the default to work
just fine for all controllers and making it overwriteable was just done
for symmetry.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
[Brian: fixed warning]
Tested-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
To be consistent with the rest of include/linux/mtd/nand.h, we should
use the __packed shorthand instead of __attribute__((packed)).
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Huang Shijie <b32955@freescale.com>
Micron provides READ RETRY support via the ONFI vendor-specific
parameter block (to indicate how many read-retry modes are available)
and the ONFI {GET,SET}_FEATURES commands with a vendor-specific feature
address (to support reading/switching the current read-retry mode).
The recommended sequence is as follows:
1. Perform PAGE_READ operation
2. If no ECC error, we are done
3. Run SET_FEATURES with feature address 89h, mode 1
4. Retry PAGE_READ operation
5. If ECC error and there are remaining supported modes, increment the
mode and return to step 3. Otherwise, this is a true ECC error.
6. Run SET_FEATURES with feature address 89h, mode 0, to return to the
default state.
This patch implements the chip->setup_read_retry() callback for
Micron and fills in the chip->read_retries.
Tested on Micron MT29F32G08CBADA, which supports 8 read-retry modes.
The Micron vendor-specific table was checked against the datasheets for
the following Micron NAND:
Needs retry Cell-type Part number Vendor revision Byte 180
----------- --------- ---------------- --------------- ------------
No SLC MT29F16G08ABABA 1 Reserved (0)
No MLC MT29F32G08CBABA 1 Reserved (0)
No SLC MT29F1G08AACWP 1 0
Yes MLC MT29F32G08CBADA 1 08h
Yes MLC MT29F64G08CBABA 2 08h
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Huang Shijie <b32955@freescale.com>
Modern MLC (and even SLC?) NAND can experience a large number of
bitflips (beyond the recommended correctability capacity) due to drifts
in the voltage threshold (Vt). These bitflips can cause ECC errors to
occur well within the expected lifetime of the flash. To account for
this, some manufacturers provide a mechanism for shifting the Vt
threshold after a corrupted read.
The generic pattern seems to be that a particular flash has N read retry
modes (where N = 0, traditionally), and after an ECC failure, the host
should reconfigure the flash to use the next available mode, then retry
the read operation. This process repeats until all bitfips can be
corrected or until the host has tried all available retry modes.
This patch adds the infrastructure support for a
vendor-specific/flash-specific callback, used for setting the read-retry
mode (i.e., voltage threshold).
For now, this patch always returns the flash to mode 0 (the default
mode) after a successful read-retry, according to the flowchart found in
Micron's datasheets. This may need to change in the future if it is
determined that eventually, mode 0 is insufficient for the majority of
the flash cells (and so for performance reasons, we should leave the
flash in mode 1, 2, etc.).
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Huang Shijie <b32955@freescale.com>
register_mtd_parser never fails; hence make it return void.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
deregister_mtd_parser never fails; hence make it return void.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Now that the last user of NAND_BBT_SCANALLPAGES has been removed, let's
kill this peculiar BBT feature flag.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Hardware:
CPU: XLP832,the 64-bit OS
NOR Flash:S29GL128S 128M
Software:
Kernel:2.6.32.41
Filesystem:JFFS2
When writing files, errors appear:
Write len 182 but return retlen 180
Write of 182 bytes at 0x072c815c failed. returned -5, retlen 180
Write len 186 but return retlen 184
Write of 186 bytes at 0x072caff4 failed. returned -5, retlen 184
These errors exist only in 64-bit systems,not in 32-bit systems. After analysis, we
found that the left shift operation is wrong in map_word_load_partial. For instance:
unsigned char buf[3] ={0x9e,0x3a,0xea};
map_bankwidth(map) is 4;
for (i=0; i < 3; i++) {
int bitpos;
bitpos = (map_bankwidth(map)-1-i)*8;
orig.x[0] &= ~(0xff << bitpos);
orig.x[0] |= buf[i] << bitpos;
}
The value of orig.x[0] is expected to be 0x9e3aeaff, but in this situation(64-bit
System) we'll get the wrong value of 0xffffffff9e3aeaff due to the 64-bit sign
extension:
buf[i] is defined as "unsigned char" and the left-shift operation will convert it
to the type of "signed int", so when left-shift buf[i] by 24 bits, the final result
will get the wrong value: 0xffffffff9e3aeaff.
If the left-shift bits are less than 24, then sign extension will not occur. Whereas
the bankwidth of the nor flash we used is 4, therefore this BUG emerges.
Signed-off-by: Pang Xunlei <pang.xunlei@zte.com.cn>
Signed-off-by: Zhang Yi <zhang.yi20@zte.com.cn>
Signed-off-by: Lu Zhongjun <lu.zhongjun@zte.com.cn>
Cc: <stable@vger.kernel.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This patch moves the char and block major number definitions
to major.h to be with the rest of the major numbers.
While doing this, include major.h in the files that need it.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This helper detects that whether the mtd's type is nand type.
Now, it's clear that the MTD_NANDFLASH stands for SLC nand only.
So use the mtd_type_is_nand() to replace the old check method
to do the nand type (include the SLC and MLC) check.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The @cellinfo fields contains unused information, such as write caching,
internal chip numbering, etc. But we only use it to check the SLC or MLC.
This patch tries to make it more clear and simple, renames the @cellinfo
to @bits_per_cell.
In order to avoiding the bisect issue, this patch also does the following
changes:
(0) add a macro NAND_CI_CELLTYPE_SHIFT to avoid the hardcode.
(1) add a helper to parse out the cell type : nand_get_bits_per_cell()
(2) parse out the cell type for extended-ID chips and the full-id nand chips.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add a helper to check if a nand chip is SLC or MLC.
This helper makes the code more readable.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
In order to implement the NAND boot for some Freescale's chips, such as
imx23/imx28/imx50/imx6, we use a tool (called kobs-ng) to burn the uboot
and some metadata to nand chip. And the ROM code will use the metadata to
configrate the BCH, and to find the uboot.
The ECC information(ecc step size, ecc strength) which is used to configrure
the BCH is part of the metadata. The kobs-ng can get the ecc strength from
the sys node /sys/*/ecc_strength now. But it can not get the ecc step size.
This patch adds a new field to store the ecc step size in mtd_info{}, and
it makes preparation for the next patches.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add an instance of an anonymous struct to store the ECC info for full id
nand chips.
@ecc.strength_ds: ECC correctability from the datasheet.
@ecc.step_ds: ECC size required by the @ecc.strength_ds,
These two fields are all from the datasheet.
Also add the necessary macros to make the code simple and clean.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
add a helper to get the supported features for ONFI nand.
Also add the neccessary macros.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Reviewed-and-tested-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Since the ONFI 2.1, the onfi spec adds the Extended Parameter Page
to store the ECC info.
The onfi spec tells us that if the nand chip's recommended ECC codeword
size is not 512 bytes, then the @ecc_bits is 0xff. The host _SHOULD_ then
read the Extended ECC information that is part of the extended parameter
page to retrieve the ECC requirements for this device.
This patch adds
[1] the neccessary fields for nand_onfi_params{},
[2] and adds the onfi_ext_ecc_info{} for Extended ECC information,
[3] adds onfi_ext_section{} for extended sections,
[4] and adds onfi_ext_param_page{} for the Extended Parameter Page.
Acked-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Huang Shijie <b32955@freescale.com>
Reviewed-and-tested-by: Brian Norris <computersforpeace@gmail.com>
[Brian: amended for checkpatch.pl]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
