The MIPS GIC driver has previously iterated over bits set in a bitmap
representing pending local IRQs by calling find_first_bit, clearing that
bit then calling find_first_bit again until all bits are clear. If
multiple interrupts are pending then this is wasteful, as find_first_bit
will have to loop over the whole bitmap from the start. Use the
for_each_set_bit macro which performs exactly what we need here instead.
It will use find_next_bit and thus only scan over the relevant part of
the bitmap, and it makes the intent of the code clearer.
This makes the same change for local interrupts that commit cae750bae4
("irqchip: mips-gic: Use for_each_set_bit to iterate over IRQs") made
for shared interrupts.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-mips@linux-mips.org
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/20160913165427.31686-1-paul.burton@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Since the device hierarchy domain was added by commit c98c1822ee
("irqchip/mips-gic: Add device hierarchy domain"), GIC local interrupts
have been broken.
Users attempting to setup a per-cpu local IRQ, for example the GIC timer
clock events code in drivers/clocksource/mips-gic-timer.c, the
setup_percpu_irq function would refuse with -EINVAL because the GIC
irqchip driver never called irq_set_percpu_devid so the
IRQ_PER_CPU_DEVID flag was never set for the IRQ. This happens because
irq_set_percpu_devid was being called from the gic_irq_domain_map
function which is no longer called.
Doing only that runs into further problems because gic_dev_domain_alloc
set the struct irq_chip for all interrupts, local or shared, to
gic_level_irq_controller despite that only being suitable for shared
interrupts. The typical outcome of this is that gic_level_irq_controller
callback functions are called for local interrupts, and then hwirq
number calculations overflow & the driver ends up attempting to access
some invalid register with an address calculated from an invalid hwirq
number. Best case scenario is that this then leads to a bus error. This
is fixed by abstracting the setup of the hwirq & chip to a new function
gic_setup_dev_chip which is used by both the root GIC IRQ domain & the
device domain.
Finally, decoding local interrupts failed because gic_dev_domain_alloc
only called irq_domain_alloc_irqs_parent for shared interrupts. Local
ones were therefore never associated with hwirqs in the root GIC IRQ
domain and the virq in gic_handle_local_int would always be 0. This is
fixed by calling irq_domain_alloc_irqs_parent unconditionally & having
gic_irq_domain_alloc handle both local & shared interrupts, which is
easy due to the aforementioned abstraction of chip setup into
gic_setup_dev_chip.
This fixes use of the MIPS GIC timer for clock events, which has been
broken since c98c1822ee ("irqchip/mips-gic: Add device hierarchy
domain") but hadn't been noticed due to a silent fallback to the MIPS
coprocessor 0 count/compare clock events device.
Fixes: c98c1822ee ("irqchip/mips-gic: Add device hierarchy domain")
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Qais Yousef <qsyousef@gmail.com>
Cc: stable@vger.kernel.org
Cc: Marc Zyngier <marc.zyngier@arm.com>
Link: http://lkml.kernel.org/r/20160913165335.31389-1-paul.burton@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The MIPS GIC driver has previously iterated over bits set in a bitmap
representing pending IRQs by calling find_first_bit, clearing that bit
then calling find_first_bit again until all bits are clear. If multiple
interrupts are pending then this is wasteful, as find_first_bit will
have to loop over the whole bitmap from the start. Use the
for_each_set_bit macro which performs exactly what we need here instead.
It will use find_next_bit and thus only scan over the relevant part of
the bitmap, and it makes the intent of the code more clear.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Link: https://lkml.kernel.org/r/20160819171119.28121-1-paul.burton@imgtec.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
If an IRQ is setup using __setup_irq(), which is used by the
request_irq() family of functions, and we are using an SMP kernel then
the affinity of the IRQ will be set via setup_affinity() immediately
after the IRQ is enabled. This call to gic_set_affinity() will lead to
the interrupt being mapped to a VPE. However there are other ways to use
IRQs which don't cause affinity to be set, for example if it is used to
chain to another IRQ controller with irq_set_chained_handler_and_data().
The irq_set_chained_handler_and_data() code path will enable the IRQ,
but will not trigger a call to gic_set_affinity() and in this case
nothing will map the interrupt to a VPE, meaning that the interrupt is
never received.
Fix this by implementing the activate operation for the GIC device IRQ
domain, using gic_shared_irq_domain_map() to map the interrupt to the
correct pin of cpu 0.
Fixes: c98c1822ee ("irqchip/mips-gic: Add device hierarchy domain")
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/20160819170715.27820-2-paul.burton@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
gic_shared_irq_domain_map() is called from gic_irq_domain_alloc() where
the wrong chip has been set, and is then overwritten. Tidy this up by
setting the correct chip the first time, and setting the
handle_level_irq handler from gic_irq_domain_alloc() too.
gic_shared_irq_domain_map() is also called from gic_irq_domain_map(),
which now calls irq_set_chip_and_handler() to retain its previous
behaviour.
This patch prepares for a follow-on which will call
gic_shared_irq_domain_map() from a callback where the lock on the struct
irq_desc is held, which without this change would cause the call to
irq_set_chip_and_handler() to lead to a deadlock.
Fixes: c98c1822ee ("irqchip/mips-gic: Add device hierarchy domain")
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/20160819170715.27820-1-paul.burton@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The use of config_enabled() against config options is ambiguous. In
practical terms, config_enabled() is equivalent to IS_BUILTIN(), but the
author might have used it for the meaning of IS_ENABLED(). Using
IS_ENABLED(), IS_BUILTIN(), IS_MODULE() etc. makes the intention
clearer.
This commit replaces config_enabled() with IS_ENABLED() where possible.
This commit is only touching bool config options.
I noticed two cases where config_enabled() is used against a tristate
option:
- config_enabled(CONFIG_HWMON)
[ drivers/net/wireless/ath/ath10k/thermal.c ]
- config_enabled(CONFIG_BACKLIGHT_CLASS_DEVICE)
[ drivers/gpu/drm/gma500/opregion.c ]
I did not touch them because they should be converted to IS_BUILTIN()
in order to keep the logic, but I was not sure it was the authors'
intention.
Link: http://lkml.kernel.org/r/1465215656-20569-1-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Stas Sergeev <stsp@list.ru>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Joshua Kinard <kumba@gentoo.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: "Dmitry V. Levin" <ldv@altlinux.org>
Cc: yu-cheng yu <yu-cheng.yu@intel.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Will Drewry <wad@chromium.org>
Cc: Nikolay Martynov <mar.kolya@gmail.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: Rafal Milecki <zajec5@gmail.com>
Cc: James Cowgill <James.Cowgill@imgtec.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Alex Smith <alex.smith@imgtec.com>
Cc: Adam Buchbinder <adam.buchbinder@gmail.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Mikko Rapeli <mikko.rapeli@iki.fi>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com>
Cc: "Luis R. Rodriguez" <mcgrof@do-not-panic.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Roland McGrath <roland@hack.frob.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Tony Wu <tung7970@gmail.com>
Cc: Huaitong Han <huaitong.han@intel.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Juergen Gross <jgross@suse.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andrea Gelmini <andrea.gelmini@gelma.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Rabin Vincent <rabin@rab.in>
Cc: "Maciej W. Rozycki" <macro@imgtec.com>
Cc: David Daney <david.daney@cavium.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull irq updates from Thomas Gleixner:
"The irq department delivers:
- new core infrastructure to allow better management of multi-queue
devices (interrupt spreading, node aware descriptor allocation ...)
- a new interrupt flow handler to support the new fangled Intel VMD
devices.
- yet another new interrupt controller driver.
- a series of fixes which addresses sparse warnings, missing
includes, missing static declarations etc from Ben Dooks.
- a fix for the error handling in the hierarchical domain allocation
code.
- the usual pile of small updates to core and driver code"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (46 commits)
genirq: Fix missing irq allocation affinity hint
irqdomain: Fix irq_domain_alloc_irqs_recursive() error handling
irq/Documentation: Correct result of echnoing 5 to smp_affinity
MAINTAINERS: Remove Jiang Liu from irq domains
genirq/msi: Fix broken debug output
genirq: Add a helper to spread an affinity mask for MSI/MSI-X vectors
genirq/msi: Make use of affinity aware allocations
genirq: Use affinity hint in irqdesc allocation
genirq: Add affinity hint to irq allocation
genirq: Introduce IRQD_AFFINITY_MANAGED flag
genirq/msi: Remove unused MSI_FLAG_IDENTITY_MAP
irqchip/s3c24xx: Fixup IO accessors for big endian
irqchip/exynos-combiner: Fix usage of __raw IO
irqdomain: Fix disposal of mappings for interrupt hierarchies
irqchip/aspeed-vic: Add irq controller for Aspeed
doc/devicetree: Add Aspeed VIC bindings
x86/PCI/VMD: Use untracked irq handler
genirq: Add untracked irq handler
irqchip/mips-gic: Populate irq_domain names
irqchip/gicv3-its: Implement two-level(indirect) device table support
...
When mapping an interrupt to a VP(E) we must use the identifier for the
VP that the hardware expects, and this does not always match up with the
Linux CPU number. Commit d46812bb0b ("irqchip: mips-gic: Use HW IDs
for VPE_OTHER_ADDR") corrected this for the cases that existed at the
time it was written, but commit 2af70a9620 ("irqchip/mips-gic: Add a
IPI hierarchy domain") added another case before the former patch was
merged. This leads to incorrectly using Linux CPU numbers when mapping
interrupts to VPs, which breaks on certain systems such as those with
multi-core I6400 CPUs. Fix by adding the appropriate call to
mips_cm_vp_id() to retrieve the expected VP identifier.
Fixes: d46812bb0b ("irqchip: mips-gic: Use HW IDs for VPE_OTHER_ADDR")
Fixes: 2af70a9620 ("irqchip/mips-gic: Add a IPI hierarchy domain")
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Qais Yousef <qsyousef@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/20160705132600.27730-1-paul.burton@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When allocating a new device IRQ, gic_dev_domain_alloc() correctly calls
irq_domain_set_hwirq_and_chip(), but gic_irq_domain_alloc() does not. This
means that gic_irq_domain believes all IRQs from the dev domain have an
hwirq of 0 and creates incorrect mappings in the linear_revmap. As
gic_irq_domain is a parent of the gic_dev_domain, this leads to an
inability to boot on devices with a GIC. Excerpt of the error:
[ 2.297649] irq 0: nobody cared (try booting with the "irqpoll" option)
...
[ 2.436963] handlers:
[ 2.439492] Disabling IRQ #0
Fix this by calling irq_domain_set_hwirq_and_chip() for both the dev and
irq domain.
Now that we are modifying the parent domain, be sure to clear it up in
case of an allocation error.
Fixes: c98c1822ee ("irqchip/mips-gic: Add device hierarchy domain")
Fixes: 2af70a9620 ("irqchip/mips-gic: Add a IPI hierarchy domain")
Signed-off-by: Harvey Hunt <harvey.hunt@imgtec.com>
Tested-by: Govindraj Raja <Govindraj.Raja@imgtec.com> # On Pistachio SoC
Reviewed-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Qais Yousef <qsyousef@gmail.com>
Cc: jason@lakedaemon.net
Cc: marc.zyngier@arm.com
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/1464001552-31174-1-git-send-email-harvey.hunt@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When EIC mode is in use (cpu_has_veic is true) enable it on each CPU
during GIC initialisation. Otherwise there may be a mismatch between the
hardware default interrupt model & that expected by the kernel.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Matt Redfearn <matt.redfearn@imgtec.com>
Tested-by: Matt Redfearn <matt.redfearn@imgtec.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13274/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Provide a gic_read_local_vp_id() function to read the VCNUM field of the
GICs local VP_IDENT register. This will be used by a further patch to
check that the value reported by the GIC matches up with the kernels
calculation.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12334/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The Linux CPU number doesn't necessarily match up with the ID used for a
VP by hardware. Convert the CPU number to the HW ID using mips_cm_vp_id
when writing to the VP(E)_OTHER_ADDR register in order to ensure that we
correctly access registers for the VPs of secondary cores. This most
notably affects systems using CM3, such as those based around I6400.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12333/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit 2a07870511 ("irqchip/mips-gic: Use gic_vpes instead of
NR_CPUS") & commit 78930f09b9 ("irqchip/mips-gic: Clear percpu_masks
correctly when mapping") both introduce code which accesses gic_vpes
entries in the pcpu_masks array. However, this array has length NR_CPUS.
If NR_CPUS is less than gic_vpes (ie. the kernel supports use of less
CPUs than are present in the system) then we overrun the array, clobber
some other data & generally die pretty promptly.
Most notably this affects uniprocessor kernels running on any multicore
or multithreaded Malta with a GIC (ie. the vast majority of real Malta
boards).
Fix this by only accessing up to min(gic_vpes, NR_CPUS) entries in the
pcpu_masks array, preventing the array overrun.
Fixes: 2a07870511 ("irqchip/mips-gic: Use gic_vpes instead of NR_CPUS")
Fixes: 78930f09b9 ("irqchip/mips-gic: Clear percpu_masks correctly when mapping")
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Link: http://lkml.kernel.org/r/1461234714-9975-1-git-send-email-paul.burton@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The new property will allow to specify the range of GIC hwirqs to use for IPIs.
This is an optinal property. We preserve the previous behaviour of allocating
the last 2 * gic_vpes if it's not specified or DT is not supported.
Signed-off-by: Qais Yousef <qais.yousef@imgtec.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: <jason@lakedaemon.net>
Cc: <marc.zyngier@arm.com>
Cc: <jiang.liu@linux.intel.com>
Cc: <linux-mips@linux-mips.org>
Cc: <lisa.parratt@imgtec.com>
Cc: Qais Yousef <qsyousef@gmail.com>
Link: http://lkml.kernel.org/r/1449580830-23652-20-git-send-email-qais.yousef@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This commit does several things to avoid breaking bisectability.
1- Remove IPI init code from irqchip/mips-gic
2- Implement the new irqchip->send_ipi() in irqchip/mips-gic
3- Select GENERIC_IRQ_IPI Kconfig symbol for MIPS_GIC
4- Change MIPS SMP to use the generic IPI implementation
Only the SMP variants that use GIC were converted as it's the only irqchip that
will have the support for generic IPI for now.
Signed-off-by: Qais Yousef <qais.yousef@imgtec.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: <jason@lakedaemon.net>
Cc: <marc.zyngier@arm.com>
Cc: <jiang.liu@linux.intel.com>
Cc: <linux-mips@linux-mips.org>
Cc: <lisa.parratt@imgtec.com>
Cc: Qais Yousef <qsyousef@gmail.com>
Link: http://lkml.kernel.org/r/1449580830-23652-18-git-send-email-qais.yousef@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When setting the mapping for a hwirq, make sure we clear percpu_masks for
all other cpus in case it was set previously.
Signed-off-by: Qais Yousef <qais.yousef@imgtec.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: <jason@lakedaemon.net>
Cc: <marc.zyngier@arm.com>
Cc: <jiang.liu@linux.intel.com>
Cc: <linux-mips@linux-mips.org>
Cc: <lisa.parratt@imgtec.com>
Cc: Qais Yousef <qsyousef@gmail.com>
Link: http://lkml.kernel.org/r/1449580830-23652-16-git-send-email-qais.yousef@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
NR_CPUS is set by Kconfig and could be much higher than what actually is in the
system.
gic_vpes should be a true representitives of the number of cpus in the system,
so use it instead.
Signed-off-by: Qais Yousef <qais.yousef@imgtec.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: <jason@lakedaemon.net>
Cc: <marc.zyngier@arm.com>
Cc: <jiang.liu@linux.intel.com>
Cc: <linux-mips@linux-mips.org>
Cc: <lisa.parratt@imgtec.com>
Cc: Qais Yousef <qsyousef@gmail.com>
Link: http://lkml.kernel.org/r/1449580830-23652-15-git-send-email-qais.yousef@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Now the root gic_irq_domain is split into device and IPI domains.
This form provides a better representation of how the root domain is split into
2. One for devices and one for IPIs.
Signed-off-by: Qais Yousef <qais.yousef@imgtec.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: <jason@lakedaemon.net>
Cc: <marc.zyngier@arm.com>
Cc: <jiang.liu@linux.intel.com>
Cc: <linux-mips@linux-mips.org>
Cc: <lisa.parratt@imgtec.com>
Cc: Qais Yousef <qsyousef@gmail.com>
Link: http://lkml.kernel.org/r/1449580830-23652-14-git-send-email-qais.yousef@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add a new ipi domain on top of the normal domain.
MIPS GIC now supports dynamic allocation of an IPI.
Signed-off-by: Qais Yousef <qais.yousef@imgtec.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: <jason@lakedaemon.net>
Cc: <marc.zyngier@arm.com>
Cc: <jiang.liu@linux.intel.com>
Cc: <linux-mips@linux-mips.org>
Cc: <lisa.parratt@imgtec.com>
Cc: Qais Yousef <qsyousef@gmail.com>
Link: http://lkml.kernel.org/r/1449580830-23652-13-git-send-email-qais.yousef@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The GIC provides a "user-mode visible" section containing a mirror of
the counter registers which can be mapped into user memory. This will
be used by the VDSO time function implementations, so provide a
function to map it in.
When the GIC is not enabled in Kconfig a dummy inline version of this
function is provided, along with "#define gic_present 0", so that we
don't have to litter the VDSO code with ifdefs.
[markos.chandras@imgtec.com:
- Move mapping code to arch/mips/kernel/vdso.c and use a resource
type to get the GIC usermode information
- Avoid renaming function arguments and use __gic_base_addr to hold
the base GIC address prior to ioremap.]
[ralf@linux-mips.org: Fix up gic_get_usm_range() to compile and make inline
again.]
Signed-off-by: Alex Smith <alex.smith@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Alex Smith <alex.smith@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/11281/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
gic_handle_shared_int reads the GIC interrupt pending & mask registers
directly into a bitmap, which is defined as an array of unsigned longs.
The GIC pending registers may be 32 bits wide if the CM is older than
CM3, regardless of the bit width of the CPU, but for MIPS64 kernels
the unsigned longs in the bitmap will be 64 bits wide. In this case we
need to perform 2 x 32 bit reads per 64 bit unsigned long in order to
avoid missing interrupts.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11213/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Make use of the mips_cm_vp_id function to convert from Linux CPU numbers
to the VP IDs used by hardware, which are not identical in all systems.
Without doing so we map interrupts to incorrect VP(E)s.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11212/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Most interrupt flow handlers do not use the irq argument. Those few
which use it can retrieve the irq number from the irq descriptor.
Remove the argument.
Search and replace was done with coccinelle and some extra helper
scripts around it. Thanks to Julia for her help!
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for 4.3 for MIPS. Here's the summary:
Three fixes that didn't make 4.2-stable:
- a -Os build might compile the kernel using the MIPS16 instruction
set but the R2 optimized inline functions in <uapi/asm/swab.h> are
implemented using 32-bit wide instructions which is invalid.
- a build error in pgtable-bits.h for a particular kernel
configuration.
- accessing registers of the CM GCR might have been compiled to use
64 bit accesses but these registers are onl 32 bit wide.
And also a few new bits:
- move the ATH79 GPIO driver to drivers/gpio
- the definition of IRQCHIP_DECLARE has moved to linux/irqchip.h,
change ATH79 accordingly.
- fix definition of pgprot_writecombine
- add an implementation of dma_map_ops.mmap
- fix alignment of quiet build output for vmlinuz link
- BCM47xx: Use kmemdup rather than duplicating its implementation
- Netlogic: Fix 0x0x prefixes of constants.
- merge Bjorn Helgaas' series to remove most of the weak keywords
from function declarations.
- CP0 and CP1 registers are best considered treated as unsigned
values to avoid large values from becoming negative values.
- improve support for the MIPS GIC timer.
- enable common clock framework for Malta and SEAD3.
- a number of improvments and fixes to dump_tlb().
- document the MIPS TLB dump functionality in Magic SysRq.
- Cavium Octeon CN68XX improvments.
- NetLogic improvments.
- irq: Use access helper irq_data_get_affinity_mask.
- handle MSA unaligned accesses.
- a number of R6-related math-emu fixes.
- support for I6400.
- improvments to MSA support.
- add uprobes support.
- move from deprecated __initcall to arch_initcall.
- remove finish_arch_switch().
- IRQ cleanups by Thomas Gleixner.
- migrate to new 'set-state' interface.
- random small cleanups"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (148 commits)
MIPS: UAPI: Fix unrecognized opcode WSBH/DSBH/DSHD when using MIPS16.
MIPS: Fix alignment of quiet build output for vmlinuz link
MIPS: math-emu: Remove unused handle_dsemul function declaration
MIPS: math-emu: Add support for the MIPS R6 MAX{, A} FPU instruction
MIPS: math-emu: Add support for the MIPS R6 MIN{, A} FPU instruction
MIPS: math-emu: Add support for the MIPS R6 CLASS FPU instruction
MIPS: math-emu: Add support for the MIPS R6 RINT FPU instruction
MIPS: math-emu: Add support for the MIPS R6 MSUBF FPU instruction
MIPS: math-emu: Add support for the MIPS R6 MADDF FPU instruction
MIPS: math-emu: Add support for the MIPS R6 SELNEZ FPU instruction
MIPS: math-emu: Add support for the MIPS R6 SELEQZ FPU instruction
MIPS: math-emu: Add support for the CMP.condn.fmt R6 instruction
MIPS: inst.h: Add new MIPS R6 FPU opcodes
MIPS: Octeon: Fix management port MII address on Kontron S1901
MIPS: BCM47xx: Use kmemdup rather than duplicating its implementation
STAGING: Octeon: Use common helpers for determining interface and port
MIPS: Octeon: Support interfaces 4 and 5
MIPS: Octeon: Set up 1:1 mapping between CN68XX PKO queues and ports
MIPS: Octeon: Initialize CN68XX PKO
STAGING: Octeon: Support CN68XX style WQE
...
Pull irq updates from Thomas Gleixner:
"This updated pull request does not contain the last few GIC related
patches which were reported to cause a regression. There is a fix
available, but I let it breed for a couple of days first.
The irq departement provides:
- new infrastructure to support non PCI based MSI interrupts
- a couple of new irq chip drivers
- the usual pile of fixlets and updates to irq chip drivers
- preparatory changes for removal of the irq argument from interrupt
flow handlers
- preparatory changes to remove IRQF_VALID"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (129 commits)
irqchip/imx-gpcv2: IMX GPCv2 driver for wakeup sources
irqchip: Add bcm2836 interrupt controller for Raspberry Pi 2
irqchip: Add documentation for the bcm2836 interrupt controller
irqchip/bcm2835: Add support for being used as a second level controller
irqchip/bcm2835: Refactor handle_IRQ() calls out of MAKE_HWIRQ
PCI: xilinx: Fix typo in function name
irqchip/gic: Ensure gic_cpu_if_up/down() programs correct GIC instance
irqchip/gic: Only allow the primary GIC to set the CPU map
PCI/MSI: pci-xgene-msi: Consolidate chained IRQ handler install/remove
unicore32/irq: Prepare puv3_gpio_handler for irq argument removal
tile/pci_gx: Prepare trio_handle_level_irq for irq argument removal
m68k/irq: Prepare irq handlers for irq argument removal
C6X/megamode-pic: Prepare megamod_irq_cascade for irq argument removal
blackfin: Prepare irq handlers for irq argument removal
arc/irq: Prepare idu_cascade_isr for irq argument removal
sparc/irq: Use access helper irq_data_get_affinity_mask()
sparc/irq: Use helper irq_data_get_irq_handler_data()
parisc/irq: Use access helper irq_data_get_affinity_mask()
mn10300/irq: Use access helper irq_data_get_affinity_mask()
irqchip/i8259: Prepare i8259_irq_dispatch for irq argument removal
...
CM3 uses a 64-bit counter and compare registers so add support for
them in the GIC counter interrupt.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10648/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Previously, the GIC accessors were only accessing u32 registers but
newer CMs may actually be 64-bit on MIPS64 cores. As a result of which,
extended these accessors to support 64-bit reads and writes.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10709/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The majority of SMP platforms handle their IPIs through do_IRQ()
which calls irq_{enter/exit}(). When a call function IPI is received,
smp_call_function_interrupt() is called which also calls
irq_{enter,exit}(), meaning irq_count is raised twice.
When tick broadcasting is used (which is implemented via a call
function IPI), this incorrectly causes all CPU idle time on the core
receiving broadcast ticks to be accounted as time spent servicing
IRQs, as account_process_tick() will account as such if irq_count is
greater than 1. This results in 100% CPU usage being reported on a
core which receives its ticks via broadcast.
This patch removes the SMP smp_call_function_interrupt() wrapper which
calls irq_{enter,exit}(). Platforms which handle their IPIs through
do_IRQ() now call generic_smp_call_function_interrupt() directly to
avoid incrementing irq_count a second time. Platforms which don't
(loongson, sgi-ip27, sibyte) call generic_smp_call_function_interrupt()
wrapped in irq_{enter,exit}().
Signed-off-by: Alex Smith <alex.smith@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10770/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use irq_set_handler_name_locked() as it avoids a redundant lookup of
the irq descriptor.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Use access helper irq_data_get_affinity_mask() to hide implementation
details of struct irq_desc.
[ tglx: Verified with coccinelle ]
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1433145945-789-30-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Wider testing reveals that the Fast Debug Channel (FDC) interrupt is
routed through the GIC just fine on Pistachio SoC, even though it
contains interAptiv cores. Clearly the FDC interrupt routing problems
previously observed on interAptiv and proAptiv cores are specific to the
Malta FPGA bitstreams.
Move the workaround for interAptiv and proAptiv out of
gic_get_c0_fdc_int() in the GIC irqchip driver into Malta's
get_c0_fdc_int() platform callback, to allow the Pistachio SoC to use
the FDC interrupt.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: linux-mips@linux-mips.org
Reviewed-by: Andrew Bresticker <abrestic@chromium.org>
Cc: James Hartley <james.hartley@imgtec.com>
Patchwork: http://patchwork.linux-mips.org/patch/9748/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pull irq updates from Thomas Gleixner:
"The irq departement delivers:
- plug a potential race related to chained interrupt handlers
- core updates which address the needs of the x86 irqdomain conversion
- new irqchip callback to support affinity settings for VCPUs
- the usual pile of updates to interrupt chip drivers
- a few helper functions to allow further cleanups and
simplifications
I have a largish pile of coccinelle scripted/verified cleanups and
simplifications pending on top of that, but I prefer to send that
towards the end of the merge window when the arch/driver changes have
hit your tree to avoid API change wreckage as far as possible"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (34 commits)
genirq: Remove bogus restriction in irq_move_mask_irq()
irqchip: atmel-aic5: Add sama5d2 support
irq: spear-shirq: Fix race in installing chained IRQ handler
irq: irq-keystone: Fix race in installing chained IRQ handler
gpio: gpio-tegra: Fix race in installing chained IRQ handler
gpio: gpio-mxs: Fix race in installing chained IRQ handler
gpio: gpio-mxc: Fix race in installing chained IRQ handler
ARM: gemini: Fix race in installing GPIO chained IRQ handler
GPU: ipu: Fix race in installing IPU chained IRQ handler
ARM: sa1100: convert SA11x0 related code to use new chained handler helper
irq: Add irq_set_chained_handler_and_data()
irqchip: exynos-combiner: Save IRQ enable set on suspend
genirq: Introduce helper function irq_data_get_affinity_mask()
genirq: Introduce helper function irq_data_get_node()
genirq: Introduce struct irq_common_data to host shared irq data
genirq: Prevent crash in irq_move_irq()
genirq: Enhance irq_data_to_desc() to support hierarchy irqdomain
irqchip: gic: Simplify gic_configure_irq by using IRQCHIP_SET_TYPE_MASKED
irqchip: renesas: intc-irqpin: Improve binding documentation
genirq: Set IRQCHIP_SKIP_SET_WAKE for no_irq_chip
...
The GIC chained handlers use do_IRQ() to call the subhandlers. This
means that irq_enter() calls get nested, which leads to preempt count
looking like we're in nested interrupts, which in turn leads to all
system time being accounted as IRQ time in account_system_time().
Fix it by using generic_handle_irq(). Since these same functions are
used in some systems (if cpu_has_veic) from a low-level vectored
interrupt handler which does not go throught do_IRQ(), we need to do it
conditionally.
Signed-off-by: Rabin Vincent <rabin.vincent@axis.com>
Reviewed-by: Andrew Bresticker <abrestic@chromium.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Cc: tglx@linutronix.de
Cc: jason@lakedaemon.net
Patchwork: https://patchwork.linux-mips.org/patch/10545/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
functions, prompted by their mis-use in staging.
With these function removed, all cpu functions should only iterate to
nr_cpu_ids, so we finally only allocate that many bits when cpumasks
are allocated offstack.
Thanks,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=VAgA
-----END PGP SIGNATURE-----
Merge tag 'cpumask-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull final removal of deprecated cpus_* cpumask functions from Rusty Russell:
"This is the final removal (after several years!) of the obsolete
cpus_* functions, prompted by their mis-use in staging.
With these function removed, all cpu functions should only iterate to
nr_cpu_ids, so we finally only allocate that many bits when cpumasks
are allocated offstack"
* tag 'cpumask-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (25 commits)
cpumask: remove __first_cpu / __next_cpu
cpumask: resurrect CPU_MASK_CPU0
linux/cpumask.h: add typechecking to cpumask_test_cpu
cpumask: only allocate nr_cpumask_bits.
Fix weird uses of num_online_cpus().
cpumask: remove deprecated functions.
mips: fix obsolete cpumask_of_cpu usage.
x86: fix more deprecated cpu function usage.
ia64: remove deprecated cpus_ usage.
powerpc: fix deprecated CPU_MASK_CPU0 usage.
CPU_MASK_ALL/CPU_MASK_NONE: remove from deprecated region.
staging/lustre/o2iblnd: Don't use cpus_weight
staging/lustre/libcfs: replace deprecated cpus_ calls with cpumask_
staging/lustre/ptlrpc: Do not use deprecated cpus_* functions
blackfin: fix up obsolete cpu function usage.
parisc: fix up obsolete cpu function usage.
tile: fix up obsolete cpu function usage.
arm64: fix up obsolete cpu function usage.
mips: fix up obsolete cpu function usage.
x86: fix up obsolete cpu function usage.
...
We add new functions to start and stop the GIC counter since there are no
guarantees the counter will be running after a CPU reset. The GIC counter
is stopped by setting the 29th bit on the GIC Config register and it is
started by clearing that bit.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9594/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add a function to the MIPS GIC driver for retrieving the Fast Debug
Channel (FDC) interrupt number, similar to the existing ones for the
timer and perf counter interrupts. This will be used by platform
implementations of get_c0_fdc_int() if a GIC is present.
A workaround exists for interAptiv and proAptiv which claim to be able
to route the FDC interrupt but don't seem to be able to in practice (at
least on Malta).
[ralf@linux-mips.org: Fix conflict.]
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/9142/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Treat the Fast Debug Channel (FDC) interrupt the same as the timer and
performance counter interrupts. Like them, the FDC IRQ is also per-VPE,
and also doesn't use a per-CPU device ID yet. Per-CPU device IDs don't
seem to work with IRQF_SHARED which is needed for compatibility with
cores which don't route the FDC IRQ through the GIC. For hardware which
routes FDC IRQs through the GIC this is something that could be added
later.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/9141/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix typo in comment in gic_get_c0_perfcount_int:
"erformance" -> "performance".
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Andrew Bresticker <abrestic@chromium.org>
Patchwork: https://patchwork.linux-mips.org/patch/9126/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Thanks to spatch, plus manual removal of "&*". Then a sweep for
for_each_cpu_mask => for_each_cpu.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: netdev@vger.kernel.org
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for MIPS:
- a number of fixes that didn't make the 3.19 release.
- a number of cleanups.
- preliminary support for Cavium's Octeon 3 SOCs which feature up to
48 MIPS64 R3 cores with FPU and hardware virtualization.
- support for MIPS R6 processors.
Revision 6 of the MIPS architecture is a major revision of the MIPS
architecture which does away with many of original sins of the
architecture such as branch delay slots. This and other changes in
R6 require major changes throughout the entire MIPS core
architecture code and make up for the lion share of this pull
request.
- finally some preparatory work for eXtendend Physical Address
support, which allows support of up to 40 bit of physical address
space on 32 bit processors"
[ Ahh, MIPS can't leave the PAE brain damage alone. It's like
every CPU architect has to make that mistake, but pee in the snow
by changing the TLA. But whether it's called PAE, LPAE or XPA,
it's horrid crud - Linus ]
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (114 commits)
MIPS: sead3: Corrected get_c0_perfcount_int
MIPS: mm: Remove dead macro definitions
MIPS: OCTEON: irq: add CIB and other fixes
MIPS: OCTEON: Don't do acknowledge operations for level triggered irqs.
MIPS: OCTEON: More OCTEONIII support
MIPS: OCTEON: Remove setting of processor specific CVMCTL icache bits.
MIPS: OCTEON: Core-15169 Workaround and general CVMSEG cleanup.
MIPS: OCTEON: Update octeon-model.h code for new SoCs.
MIPS: OCTEON: Implement DCache errata workaround for all CN6XXX
MIPS: OCTEON: Add little-endian support to asm/octeon/octeon.h
MIPS: OCTEON: Implement the core-16057 workaround
MIPS: OCTEON: Delete unused COP2 saving code
MIPS: OCTEON: Use correct instruction to read 64-bit COP0 register
MIPS: OCTEON: Save and restore CP2 SHA3 state
MIPS: OCTEON: Fix FP context save.
MIPS: OCTEON: Save/Restore wider multiply registers in OCTEON III CPUs
MIPS: boot: Provide more uImage options
MIPS: Remove unneeded #ifdef __KERNEL__ from asm/processor.h
MIPS: ip22-gio: Remove legacy suspend/resume support
mips: pci: Add ifdef around pci_proc_domain
...
Pull irqchip updates from Ingo Molnar:
"Various irqchip driver updates, plus a genirq core update that allows
the initial spreading of irqs amonst CPUs without having to do it from
user-space"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq: Fix null pointer reference in irq_set_affinity_hint()
irqchip: gic: Allow interrupt level to be set for PPIs
irqchip: mips-gic: Handle pending interrupts once in __gic_irq_dispatch()
irqchip: Conexant CX92755 interrupts controller driver
irqchip: Devicetree: document Conexant Digicolor irq binding
irqchip: omap-intc: Remove unused legacy interface for omap2
irqchip: omap-intc: Fix support for dm814 and dm816
irqchip: mtk-sysirq: Get irq number from register resource size
irqchip: renesas-intc-irqpin: r8a7779 IRLM setup support
genirq: Set initial affinity in irq_set_affinity_hint()
The cevt-r4k driver used to call into the GIC driver to find whether the
timer was pending, but only with External Interrupt Controller (EIC)
mode, where the Cause.IP bits can't be used as they encode the interrupt
priority level (Cause.RIPL) instead.
However commit e9de688dac ("irqchip: mips-gic: Support local
interrupts") changed the condition from cpu_has_veic to gic_present.
This fails on cores such as P5600 which have a GIC but the local
interrupts aren't routable by the GIC, causing c0_compare_int_usable()
to consider the interrupt unusable so r4k_clockevent_init() fails.
The previous behaviour, added in commit 98b67c37db ("MIPS: Add EIC
support for GIC."), wasn't really correct either as far as I can tell,
since P5600 apparently supports EIC mode too, and in any case the use of
Cause.TI with r2 should have been sufficient anyway since commit
010c108d7a ("MIPS: PowerTV: Fix support for timer interrupts with > 64
external IRQs").
Therefore drop the call into the gic driver altogether, and add a
comment in c0_compare_int_pending() to clarify that Cause.TI does get
checked since MIPS r2.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Fixes: e9de688dac ("irqchip: mips-gic: Support local interrupts")
Reviewed-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Steven J. Hill <steven.hill@imgtec.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9077/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit e9de688dac ("irqchip: mips-gic: Support local interrupts")
changed the GIC irqchip driver so that all local interrupts were routed
to the same CPU pin used for external interrupts. Unfortunately this
causes a regression when smp-cmp is used. The CPUs are started by the
bootloader and put in a timer based waiting poll loop, but when their
timer interrupts are rerouted to a different IRQ pin which is not
unmasked they never wake up.
Since smp-cmp support is deprecated and everybody who was using it
should be switching to smp-cps which brings up the secondary CPUs
without bootloader assistance, I've gone for the simple fix which can be
easily removed once smp-cmp is removed, rather than a fully generic fix.
In __gic_init() the local GIC_VPE_TIMER_MAP register is read to find the
boot-time routing of the local timer interrupt, and a chained handler is
added to that CPU pin as well as the normal one.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Fixes: e9de688dac ("irqchip: mips-gic: Support local interrupts")
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Reviewed-by: Andrew Bresticker <abrestic@chromium.org>
Patchwork: https://patchwork.linux-mips.org/patch/9081/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
