Currently dw_pcie_setup_rc() configures memory base and memory limit in the
type1 configuration header for the root complex. In doing so it uses the
CPU address (pp->mem_base) rather than the bus address (pp->mem_bus_addr).
This is wrong and it is useless since the configuration is overwritten
later on when pci_bus_assign_resources() is called.
Remove this configuration from dw_pcie_setup_rc().
Signed-off-by: Gabriele Paoloni <gabriele.paoloni@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Pratyush Anand <pratyush.anand@gmail.com>
dw_pcie_host_init() looks up host bridge resources, ioremaps them, creates
IRQ domains, and enumerates devices below the bridge. dw_pcie_setup_rc()
programs the Root Complex registers. The Root Complex may lose power
during suspend-to-RAM, and when we resume, we want to redo the latter but
not the former.
Move some Root Complex programming from dw_pcie_host_init() to
dw_pcie_setup_rc() where it belongs. DesignWare-based drivers can call
dw_pcie_setup_rc() in their resume paths.
[Niklas Cassel <niklas.cassel@axis.com>: This change moves outbound ATU
programming, which uses pp->mem_base, to dw_pcie_setup_rc(). Apply the
dra7xx pp->mem_base update before calling dw_pcie_setup_rc().]
[bhelgaas: changelog, fold in dra7xx fix from Niklas]
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Pratyush Anand <pratyush.anand@gmail.com>
Add a default DesignWare "link_up" test for use when a sub-driver doesn't
supply its own pcie_host_ops.link_up() method.
[bhelgaas: changelog, split into its own patch]
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Pratyush Anand <pratyush.anand@gmail.com>
Several DesignWare-based drivers (dra7xx, exynos, imx6, keystone, qcom, and
spear13xx) had similar loops waiting for the link to come up.
Add a generic dw_pcie_wait_for_link() for use by all these drivers so the
waiting is done consistently, e.g., always using usleep_range() rather than
mdelay() and using similar timeouts and retry counts.
Note that this changes the Keystone link training/wait for link strategy,
so we initiate link training, then wait longer for the link to come up
before re-initiating link training.
[bhelgaas: changelog, split into its own patch, update pci-keystone.c, pcie-qcom.c]
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Pratyush Anand <pratyush.anand@gmail.com>
The PCIe designware host driver is not used in system configurations
requiring the PCI_PROBE_ONLY flag to be set to prevent resources
assignment, therefore the driver code handling the flag can be removed
from the kernel.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Pratyush Anand <pratyush.anand@gmail.com>
Acked-by: Jingoo Han Jingoo Han <jingoohan1@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Gabriele Paoloni <gabriele.paoloni@huawei.com>
Cc: Zhou Wang <wangzhou1@hisilicon.com>
Some platforms don't support ATU, e.g., pci-keystone.c. These platforms
use their own address translation component rather than ATU, and they
provide the rd_other_conf and wr_other_conf methods to program the
translation component and perform the access.
Add a comment to explain why we don't program the ATU for these platforms.
[bhelgaas: changelog]
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Drivers based on the DesignWare core can override the config read accessors
by supplying rd_own_conf() and rd_other_conf() function pointers.
dw_pcie_rd_conf() calls dw_pcie_rd_own_conf() (for accesses to the root
bus) or dw_pcie_rd_other_conf():
dw_pcie_rd_conf
dw_pcie_rd_own_conf # if on root bus
dw_pcie_rd_other_conf # if not on root bus
Previously we checked for rd_other_conf() directly in dw_pcie_rd_conf(),
but we checked for rd_own_conf() in dw_pcie_rd_own_conf().
Check for rd_other_conf() in dw_pcie_rd_other_conf() to make this symmetric
with the rd_own_conf() checking, and similarly for the write path.
No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Pratyush Anand <pratyush.anand@gmail.com>
Return values immediately when possible to simplify the control flow.
No functional change intended. Folded in unused variable removal as
pointed out by Fabio Estevam <fabio.estevam@nxp.com>, Arnd Bergmann
<arnd@arndb.de>, and Thierry Reding <thierry.reding@gmail.com>.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Pratyush Anand <pratyush.anand@gmail.com>
Read back the ATU CR2 register to ensure ATU programming is effective
before any subsequent I/O or config space accesses.
Without this, PCI device enumeration is unreliable.
[bhelgaas: changelog, comment]
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Pratyush Anand <pratyush.anand@gmail.com>
"pp->io" is an I/O resource, e.g., "[io 0x0000-0xffff]"; "pp->io_base" is
the CPU physical address of a region where the host bridge converts CPU
memory accesses into PCI I/O transactions.
Corrupting pp->io_base by assigning pp->io->start to it breaks access to
the PCI I/O space, as reported by Kishon.
Remove the invalid assignment.
[bhelgaas: changelog]
Fixes: 0021d22b73 ("PCI: designware: Use of_pci_get_host_bridge_resources() to parse DT")
Reported-and-tested-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Previously, dw_pcie_host_init() created the PCI host bridge with
pci_common_init_dev(), an ARM-specific function that supplies the ARM-
specific pci_sys_data structure as the PCI "sysdata".
Make pcie-designware.c arch-agnostic by reimplementing the functionality of
pci_common_init_dev() directly in dw_pcie_host_init().
Note that this changes the bridge sysdata from the ARM pci_sys_data to the
DesignWare pcie_port structure. This doesn't affect the ARM sysdata users
because they are all specific to non-DesignWare host bridges, which will
still have pci_sys_data.
[bhelgaas: changelog]
Tested-by: James Morse <james.morse@arm.com>
Tested-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Tested-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Gabriele Paoloni <gabriele.paoloni@huawei.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Pratyush Anand <pratyush.anand@gmail.com>
Use the new of_pci_get_host_bridge_resources() API in place of the PCI OF
DT parser.
[bhelgaas: changelog]
Tested-by: James Morse <james.morse@arm.com>
Tested-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Tested-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Gabriele Paoloni <gabriele.paoloni@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Pratyush Anand <pratyush.anand@gmail.com>
Revert f4c55c5a3f ("PCI: designware: Program ATU with untranslated
address").
Note that dra7xx_pcie_host_init() now modifies pp->io_base, but we still
need the original value for dw_pcie_setup() in the path below, so this adds
a new io_base_tmp member. It will be removed later when dw_pcie_setup() is
removed.
dra7xx_add_pcie_port
dw_pcie_host_init
pp->io_base = range.cpu_addr
pp->io_base_tmp = range.cpu_addr # <-- added
pp->ops->host_init
dra7xx_pcie_host_init # ops->host_init
pp->io_base &= DRA7XX_CPU_TO_BUS_ADDR # <-- modified
pci_common_init_dev(..., &dw_pci)
pcibios_init_hw
hw->setup
dw_pcie_setup # hw_pci.setup
pci_ioremap_io(..., pp->io_base_tmp) # <-- original addr required
[bhelgaas: changelog]
Tested-by: James Morse <james.morse@arm.com>
Tested-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Tested-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Gabriele Paoloni <gabriele.paoloni@huawei.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Pratyush Anand <pratyush.anand@gmail.com>
Commit f4c55c5a3f ("PCI: designware: Program ATU with untranslated
address") added the calculation of PCI bus addresses in pcie-designware.c,
storing them in new fields added in struct pcie_port. This calculation is
done for every DesignWare user even though it only applies to DRA7xx.
Move the calculation of the bus addresses to the DRA7xx driver to allow the
rework of DesignWare to use the new DT parsing API.
Signed-off-by: Gabriele Paoloni <gabriele.paoloni@huawei.com>
Signed-off-by: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Pratyush Anand <pratyush.anand@gmail.com>
Currently "num-lanes" is read in dw_pcie_host_init(), but it is only used
if we call dw_pcie_setup_rc() while bringing up the link. If the link has
already been brought up by firmware, we need not call dw_pcie_setup_rc(),
and "num-lanes" is unnecessary.
Only complain about "num-lanes" if we actually need it and we didn't find a
valid value.
[bhelgaas: changelog]
Signed-off-by: Gabriele Paoloni <gabriele.paoloni@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add sanity checks on "addr" input parameter in dw_pcie_cfg_read() and
dw_pcie_cfg_write(). These checks make sure that accesses are aligned on
their size, e.g., a 4-byte config access is aligned on a 4-byte boundary.
[bhelgaas: changelog, set *val = 0 in failure case]
Signed-off-by: Gabriele Paoloni <gabriele.paoloni@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Pratyush Anand <pratyush.anand@gmail.com>
Callers of dw_pcie_cfg_read() and dw_pcie_cfg_write() previously had to
split the address into "addr" and "where". The callees assumed "addr" was
32-bit aligned (with zeros in the low two bits) and they used only the low
two bits of "where".
Accept the entire address in "addr" and drop the now-redundant "where"
argument. As an example, this replaces this:
int dw_pcie_cfg_read(void __iomem *addr, int where, int size, u32 *val)
*val = readb(addr + (where & 1));
with this:
int dw_pcie_cfg_read(void __iomem *addr, int size, u32 *val)
*val = readb(addr):
[bhelgaas: changelog, split access size change to separate patch]
Signed-off-by: Gabriele Paoloni <gabriele.paoloni@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
dw_pcie_cfg_write() uses the exact 8-, 16-, or 32-bit access size
requested, but dw_pcie_cfg_read() previously performed a 32-bit read and
masked out the bits requested.
Use the exact access size in dw_pcie_cfg_read(). For example, if we want
an 8-bit read, use readb() instead of using readl() and masking out the 8
bits we need. This makes it symmetric with dw_pcie_cfg_write().
[bhelgaas: split into separate patch, set *val = 0 in failure case]
Signed-off-by: Gabriele Paoloni <gabriele.paoloni@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Set up the high part of the MSI target address to allow the MSI target to
be above 4GB on 64bit and PAE systems.
[bhelgaas: changelog]
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Pratyush Anand <pratyush.anand@gmail.com>
Implement multivector MSI IRQ setup. This allows to set up and use multiple
MSI IRQs per device.
[bhelgaas: changelog, use -EINVAL instead of -ENOSYS]
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Pratyush Anand <pratyush.anand@gmail.com>
Factor out the PCI MSI message setup from the single MSI setup function.
This will be reused by the multivector MSI setup.
No functional change yet.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Pratyush Anand <pratyush.anand@gmail.com>
The value under PORT_LOGIC_LINK_WIDTH_MASK is 0x1, 0x2, 0x4, 0x8. In IP
v4.2, bits [16:8] are defined for NUM_OF_LANES. But in IP v4.4, bits[12:8]
are defined for NUM_OF_LANES, bits [16:13] are for other usages (bit 16 is
AUTO_LANE_FLIP_CTRL_EN, bits [15:13] are PRE_DET_LANE).
As there is no conflict about NUM_OF_LANES between v4.2 and v4.4, change
the mask value to avoid future problems.
Signed-off-by: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Pull irq updates from Thomas Gleixner:
"This updated pull request does not contain the last few GIC related
patches which were reported to cause a regression. There is a fix
available, but I let it breed for a couple of days first.
The irq departement provides:
- new infrastructure to support non PCI based MSI interrupts
- a couple of new irq chip drivers
- the usual pile of fixlets and updates to irq chip drivers
- preparatory changes for removal of the irq argument from interrupt
flow handlers
- preparatory changes to remove IRQF_VALID"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (129 commits)
irqchip/imx-gpcv2: IMX GPCv2 driver for wakeup sources
irqchip: Add bcm2836 interrupt controller for Raspberry Pi 2
irqchip: Add documentation for the bcm2836 interrupt controller
irqchip/bcm2835: Add support for being used as a second level controller
irqchip/bcm2835: Refactor handle_IRQ() calls out of MAKE_HWIRQ
PCI: xilinx: Fix typo in function name
irqchip/gic: Ensure gic_cpu_if_up/down() programs correct GIC instance
irqchip/gic: Only allow the primary GIC to set the CPU map
PCI/MSI: pci-xgene-msi: Consolidate chained IRQ handler install/remove
unicore32/irq: Prepare puv3_gpio_handler for irq argument removal
tile/pci_gx: Prepare trio_handle_level_irq for irq argument removal
m68k/irq: Prepare irq handlers for irq argument removal
C6X/megamode-pic: Prepare megamod_irq_cascade for irq argument removal
blackfin: Prepare irq handlers for irq argument removal
arc/irq: Prepare idu_cascade_isr for irq argument removal
sparc/irq: Use access helper irq_data_get_affinity_mask()
sparc/irq: Use helper irq_data_get_irq_handler_data()
parisc/irq: Use access helper irq_data_get_affinity_mask()
mn10300/irq: Use access helper irq_data_get_affinity_mask()
irqchip/i8259: Prepare i8259_irq_dispatch for irq argument removal
...
ARM previously stored the msi_controller pointer in its sysdata, struct
pci_sys_data, and implemented pcibios_msi_controller() to retrieve it.
That made PCI host controller drivers specific to ARM because they had to
put the msi_controller pointer in the ARM-specific pci_sys_data.
There is now a generic mechanism, pci_scan_root_bus_msi(), for giving the
msi_controller pointer to the PCI core. Use this for all ARM systems and
for the DesignWare and Xilinx PCI host controller drivers.
This removes an ARM dependency from the DesignWare, DRA7xx, EXYNOS, i.MX6,
Keystone, Layerscape, SPEAr13xx, and Xilinx drivers.
[bhelgaas: changelog, split into separate patch]
Suggested-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
CC: Pratyush Anand <pratyush.anand@gmail.com>
CC: Arnd Bergmann <arnd@arndb.de>
CC: Simon Horman <horms@verge.net.au>
CC: Russell King <linux@arm.linux.org.uk>
CC: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
CC: Thierry Reding <thierry.reding@gmail.com>
CC: Michal Simek <michal.simek@xilinx.com>
CC: Marc Zyngier <marc.zyngier@arm.com>
* pci/hotplug:
PCI: pciehp: Remove ignored MRL sensor interrupt events
PCI: pciehp: Remove unused interrupt events
PCI: pciehp: Handle invalid data when reading from non-existent devices
PCI: Hold pci_slot_mutex while searching bus->slots list
PCI: Protect pci_bus->slots with pci_slot_mutex, not pci_bus_sem
PCI: pciehp: Simplify pcie_poll_cmd()
PCI: Use "slot" and "pci_slot" for struct hotplug_slot and struct pci_slot
* pci/iommu:
PCI: Remove pci_ats_enabled()
PCI: Stop caching ATS Invalidate Queue Depth
PCI: Move ATS declarations to linux/pci.h so they're all together
PCI: Clean up ATS error handling
PCI: Use pci_physfn() rather than looking up physfn by hand
PCI: Inline the ATS setup code into pci_ats_init()
PCI: Rationalize pci_ats_queue_depth() error checking
PCI: Reduce size of ATS structure elements
PCI: Embed ATS info directly into struct pci_dev
PCI: Allocate ATS struct during enumeration
iommu/vt-d: Cache PCI ATS state and Invalidate Queue Depth
* pci/irq:
PCI: Kill off set_irq_flags() usage
* pci/virtualization:
PCI: Add ACS quirks for Intel I219-LM/V
set_irq_flags is ARM-specific with custom flags which have genirq
equivalents. Convert drivers to use the genirq interfaces directly, so we
can kill off set_irq_flags. The translation of flags is as follows:
IRQF_VALID -> !IRQ_NOREQUEST
IRQF_PROBE -> !IRQ_NOPROBE
IRQF_NOAUTOEN -> IRQ_NOAUTOEN
For IRQs managed by an irqdomain, the irqdomain core code handles clearing
and setting IRQ_NOREQUEST already, so there is no need to do this in .map()
functions, and we can simply remove the set_irq_flags calls. Some users
also modify IRQ_NOPROBE, and this has been maintained although it is not
clear that is really needed. There appears to be a great deal of blind
copy and paste of this code.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
CC: Kishon Vijay Abraham I <kishon@ti.com>
CC: Murali Karicheri <m-karicheri2@ti.com>
CC: Thierry Reding <thierry.reding@gmail.com>
CC: Stephen Warren <swarren@wwwdotorg.org>
CC: Alexandre Courbot <gnurou@gmail.com>
CC: Jingoo Han <jingoohan1@gmail.com>
CC: Pratyush Anand <pratyush.anand@gmail.com>
CC: Simon Horman <horms@verge.net.au>
CC: Michal Simek <michal.simek@xilinx.com>
CC: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
Currently on Keystone SoCs, we always complain:
keystone-pcie 21021000.pcie: missing *config* reg space
Keystone uses an older version of DesignWare hardware that doesn't have
ATU support. So va_cfg0_base and va_cfg1_base are already set up in
ks_dw_pcie_host_init() before calling dw_pcie_host_init(), and they point
to the remote config space address va (both same for Keystone). Add a
check to avoid this boot noise on Keystone.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Rename irq_data_get_msi() as irq_data_get_msi_desc() to keep consistency
with other irq_data access helpers.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
After b97ea289cf ("PCI: Assign resources before drivers claim devices
(pci_scan_root_bus())"), pci_scan_root_bus() no longer adds the devices, so
it is equivalent to:
pci_create_root_bus()
pci_scan_child_bus()
Use pci_scan_root_bus() to simplify the code.
[bhelgaas: changelog]
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
CC: Mohit Kumar <mohit.kumar@st.com>
Most transactions' type are cfg0 and MEM, so the current iATU usage is not
balanced: iATU0 is hot while iATU1 is rarely used.
Refactor the iATU usage so we use iATU0 for cfg and IO and iATU1 for MEM.
This allocation idea comes from Minghuan Lian
<Minghuan.Lian@freescale.com>:
[bhelgaas: use link with Message-ID]
Link: http://lkml.kernel.org/r/1429091315-31891-3-git-send-email-Minghuan.Lian@freescale.com
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Pratyush Anand <pratyush.anand@gmail.com>
Currently, the outbound iATU programming functions are similar: the only
difference is index, type, addr and size. Consolidate these functions into
one. This saves about 1700 bytes in text:
text data bss dec hex filename
9276 204 4 9484 250c pcie-designware.o-before
7532 204 4 7740 1e3c pcie-designware.o
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Pratyush Anand <pratyush.anand@gmail.com>
Struct spear13xx_pcie_driver was in initdata, but we passed a pointer to it
to platform_driver_register(), which can use the pointer at arbitrary times
in the future, even after the initdata is freed. That leads to crashes.
Move spear13xx_pcie_driver and things referenced by it
(spear13xx_pcie_probe() and dw_pcie_host_init()) out of initdata.
[bhelgaas: changelog]
Fixes: 6675ef212d ("PCI: spear: Fix Section mismatch compilation warning for probe()")
Signed-off-by: Matwey V. Kornilov <matwey@sai.msu.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
CC: stable@vger.kernel.org # v3.17+
The DesignWare PCIe MSI hardware does not support MSI-X IRQs. Setting
those up failed as a side effect of a bug which was fixed by 91f8ae823f
("PCI: designware: Setup and clear exactly one MSI at a time").
Now that this bug is fixed, MSI-X IRQs need to be rejected explicitly;
otherwise devices trying to use them may end up with incorrectly working
interrupts.
Fixes: 91f8ae823f ("PCI: designware: Setup and clear exactly one MSI at a time")
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
CC: stable@vger.kernel.org # v3.18+
Most if not all ARM PCI host controller device drivers either ignore the
domain field in the pci_sys_data structure or just increment it every time
a host controller is probed, using it as a domain counter.
Therefore, instead of relying on pci_sys_data to stash the domain number in
a standard location, ARM pcibios code can be moved to the newly introduced
generic PCI domains code, implemented in commits:
41e5c0f81d ("of/pci: Add pci_get_new_domain_nr() and of_get_pci_domain_nr()")
670ba0c888 ("PCI: Add generic domain handling")
ARM code is made to select PCI_DOMAINS_GENERIC by default, which builds
core PCI code that assigns the domain number through the generic function:
void pci_bus_assign_domain_nr(...)
that relies on a DT property to define the domain number or falls back to a
counter according to a predefined logic; its usage replaces the current
domain assignment code in PCI host controllers present in the kernel.
Tested-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Yijing Wang <wangyijing@huawei.com>
Reviewed-By: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> # mvebu
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Phil Edworthy <phil.edworthy@renesas.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
CC: Mohit Kumar <mohit.kumar@st.com>
The PCI/MSI irq chip callbacks mask/unmask_msi_irq have been renamed
to pci_msi_mask/unmask_irq to mark them PCI specific. Rename all usage
sites. The conversion helper functions are kept around to avoid
conflicts in next and will be removed after merging into mainline.
Coccinelle assisted conversion. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: x86@kernel.org
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Mohit Kumar <mohit.kumar@st.com>
Cc: Simon Horman <horms@verge.net.au>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Yijing Wang <wangyijing@huawei.com>
Rename write_msi_msg() to pci_write_msi_msg() to mark it as PCI
specific.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Yingjoe Chen <yingjoe.chen@mediatek.com>
Cc: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Save MSI controller in pci_sys_data instead of assigning MSI controller
pointer to every PCI bus in .add_bus().
[bhelgaas: use dw_pcie_msi_chip, not dw_pcie_msi_controller]
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This patch fixes the following checkpatch warning:
WARNING: Missing a blank line after declarations
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
"msi_chip" isn't very descriptive, so rename it to "msi_controller". That
tells a little more about what it does and is already used in device tree
bindings.
No functional change.
[bhelgaas: changelog, change *only* the struct name so it's reviewable]
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Replace them by using the standard kernel bitmap ops. No functional
change, but makes the code a lot cleaner.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Pratyush Anand <pratyush.anand@st.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
The setup_irq function is supposed to set up exactly one MSI IRQ. Multiple
IRQ setup is handled differently, to respect the choices made by the upper
layers.
Also only clear one MSI IRQ at a time; the PCI core will call into this
function multiple times if it has to tear down more than one MSI IRQ.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Pratyush Anand <pratyush.anand@st.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Add a struct pcie_host_ops .get_msi_data() method for platforms to return
their special MSI message data.
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Mohit KUMAR <mohit.kumar@st.com>
