- Numerous minor fixes, cleanups etc.
- More EEH work from Gavin to remove its dependency on device_nodes.
- Memory hotplug implemented entirely in the kernel from Nathan Fontenot.
- Removal of redundant CONFIG_PPC_OF by Kevin Hao.
- Rewrite of VPHN parsing logic & tests from Greg Kurz.
- A fix from Nish Aravamudan to reduce memory usage by clamping
nodes_possible_map.
- Support for pstore on powernv from Hari Bathini.
- Removal of old powerpc specific byte swap routines by David Gibson.
- Fix from Vasant Hegde to prevent the flash driver telling you it was flashing
your firmware when it wasn't.
- Patch from Ben Herrenschmidt to add an OPAL heartbeat driver.
- Fix for an oops causing get/put_cpu_var() imbalance in perf by Jan Stancek.
- Some fixes for migration from Tyrel Datwyler.
- A new syscall to switch the cpu endian by Michael Ellerman.
- Large series from Wei Yang to implement SRIOV, reviewed and acked by Bjorn.
- A fix for the OPAL sensor driver from Cédric Le Goater.
- Fixes to get STRICT_MM_TYPECHECKS building again by Michael Ellerman.
- Large series from Daniel Axtens to make our PCI hooks per PHB rather than per
machine.
- Small patch from Sam Bobroff to explicitly abort non-suspended transactions
on syscalls, plus a test to exercise it.
- Numerous reworks and fixes for the 24x7 PMU from Sukadev Bhattiprolu.
- Small patch to enable the hard lockup detector from Anton Blanchard.
- Fix from Dave Olson for missing L2 cache information on some CPUs.
- Some fixes from Michael Ellerman to get Cell machines booting again.
- Freescale updates from Scott: Highlights include BMan device tree nodes, an
MSI erratum workaround, a couple minor performance improvements, config
updates, and misc fixes/cleanup.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=03Yh
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux
Pull powerpc updates from Michael Ellerman:
- Numerous minor fixes, cleanups etc.
- More EEH work from Gavin to remove its dependency on device_nodes.
- Memory hotplug implemented entirely in the kernel from Nathan
Fontenot.
- Removal of redundant CONFIG_PPC_OF by Kevin Hao.
- Rewrite of VPHN parsing logic & tests from Greg Kurz.
- A fix from Nish Aravamudan to reduce memory usage by clamping
nodes_possible_map.
- Support for pstore on powernv from Hari Bathini.
- Removal of old powerpc specific byte swap routines by David Gibson.
- Fix from Vasant Hegde to prevent the flash driver telling you it was
flashing your firmware when it wasn't.
- Patch from Ben Herrenschmidt to add an OPAL heartbeat driver.
- Fix for an oops causing get/put_cpu_var() imbalance in perf by Jan
Stancek.
- Some fixes for migration from Tyrel Datwyler.
- A new syscall to switch the cpu endian by Michael Ellerman.
- Large series from Wei Yang to implement SRIOV, reviewed and acked by
Bjorn.
- A fix for the OPAL sensor driver from Cédric Le Goater.
- Fixes to get STRICT_MM_TYPECHECKS building again by Michael Ellerman.
- Large series from Daniel Axtens to make our PCI hooks per PHB rather
than per machine.
- Small patch from Sam Bobroff to explicitly abort non-suspended
transactions on syscalls, plus a test to exercise it.
- Numerous reworks and fixes for the 24x7 PMU from Sukadev Bhattiprolu.
- Small patch to enable the hard lockup detector from Anton Blanchard.
- Fix from Dave Olson for missing L2 cache information on some CPUs.
- Some fixes from Michael Ellerman to get Cell machines booting again.
- Freescale updates from Scott: Highlights include BMan device tree
nodes, an MSI erratum workaround, a couple minor performance
improvements, config updates, and misc fixes/cleanup.
* tag 'powerpc-4.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux: (196 commits)
powerpc/powermac: Fix build error seen with powermac smp builds
powerpc/pseries: Fix compile of memory hotplug without CONFIG_MEMORY_HOTREMOVE
powerpc: Remove PPC32 code from pseries specific find_and_init_phbs()
powerpc/cell: Fix iommu breakage caused by controller_ops change
powerpc/eeh: Fix crash in eeh_add_device_early() on Cell
powerpc/perf: Cap 64bit userspace backtraces to PERF_MAX_STACK_DEPTH
powerpc/perf/hv-24x7: Fail 24x7 initcall if create_events_from_catalog() fails
powerpc/pseries: Correct memory hotplug locking
powerpc: Fix missing L2 cache size in /sys/devices/system/cpu
powerpc: Add ppc64 hard lockup detector support
oprofile: Disable oprofile NMI timer on ppc64
powerpc/perf/hv-24x7: Add missing put_cpu_var()
powerpc/perf/hv-24x7: Break up single_24x7_request
powerpc/perf/hv-24x7: Define update_event_count()
powerpc/perf/hv-24x7: Whitespace cleanup
powerpc/perf/hv-24x7: Define add_event_to_24x7_request()
powerpc/perf/hv-24x7: Rename hv_24x7_event_update
powerpc/perf/hv-24x7: Move debug prints to separate function
powerpc/perf/hv-24x7: Drop event_24x7_request()
powerpc/perf/hv-24x7: Use pr_devel() to log message
...
Conflicts:
tools/testing/selftests/powerpc/Makefile
tools/testing/selftests/powerpc/tm/Makefile
Use orderly_reboot so userspace will to shut itself down via the reboot
path. This is required for graceful reboot initiated by the BMC, such as
when a user uses ipmitool to issue a 'chassis power cycle' command.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Cc: Fabian Frederick <fabf@skynet.be>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jeremy Kerr <jk@ozlabs.org>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
powermac smp builds fail with
arch/powerpc/platforms/powermac/smp.c: In function 'smp_psurge_probe':
arch/powerpc/platforms/powermac/smp.c:278:3: error:
'return' with a value, in function returning void
There are several instances of this error.
Fixes: a7f4ee1fe9 ("powerpc: Drop return value of smp_ops->probe()")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
51925fb3c5 "powerpc/pseries: Implement memory hotplug remove in the kernel"
broke compile when CONFIG_MEMORY_HOTREMOVE is not defined due to missing
symbols. This fixes the issue by adding the missing symbols.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Acked-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Pull trivial tree from Jiri Kosina:
"Usual trivial tree updates. Nothing outstanding -- mostly printk()
and comment fixes and unused identifier removals"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
goldfish: goldfish_tty_probe() is not using 'i' any more
powerpc: Fix comment in smu.h
qla2xxx: Fix printks in ql_log message
lib: correct link to the original source for div64_u64
si2168, tda10071, m88ds3103: Fix firmware wording
usb: storage: Fix printk in isd200_log_config()
qla2xxx: Fix printk in qla25xx_setup_mode
init/main: fix reset_device comment
ipwireless: missing assignment
goldfish: remove unreachable line of code
coredump: Fix do_coredump() comment
stacktrace.h: remove duplicate declaration task_struct
smpboot.h: Remove unused function prototype
treewide: Fix typo in printk messages
treewide: Fix typo in printk messages
mod_devicetable: fix comment for match_flags
In bdc728a849 ("powerpc: move find_and_init_phbs() to pSeries
specific code"), find_and_init_phbs() was moved into a pseries
specific file, but PPC32 code wasn't removed. Remove it.
See https://lkml.kernel.org/r/552C0AA6.4010403@fau.de
Reported-by: Andreas Ruprecht <andreas.ruprecht@fau.de>
Fixes: bdc728a849
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The recent patch to convert cell to use pci_controller_ops had a small
bug which broke machines using an iommu.
The set of phb->controller_ops was added after the check for name !=
"pci", meaning pcix/pcie PHBs weren't getting their ops set correctly.
Fixes: 9c1368fc50 ("powerpc/cell: Move controller ops from ppc_md to controller_ops")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Merge Richard's work to support SR-IOV on PowerNV. All generic PCI
patches acked by Bjorn.
Some minor conflicts with Daniel's pci_controller_ops work.
Conflicts:
arch/powerpc/include/asm/machdep.h
arch/powerpc/platforms/powernv/pci-ioda.c
Memory dlpar handling can return from dlpar_memory() without releasing the
device_hotplug lock. Correct this routine to ensure the lock is released.
Fixes: 5f97b2a0d1 ("powerpc/pseries: Implement memory hotplug add in the kernel")
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Pull core locking changes from Ingo Molnar:
"Main changes:
- jump label asm preparatory work for PowerPC (Anton Blanchard)
- rwsem optimizations and cleanups (Davidlohr Bueso)
- mutex optimizations and cleanups (Jason Low)
- futex fix (Oleg Nesterov)
- remove broken atomicity checks from {READ,WRITE}_ONCE() (Peter
Zijlstra)"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
powerpc, jump_label: Include linux/jump_label.h to get HAVE_JUMP_LABEL define
jump_label: Allow jump labels to be used in assembly
jump_label: Allow asm/jump_label.h to be included in assembly
locking/mutex: Further simplify mutex_spin_on_owner()
locking: Remove atomicy checks from {READ,WRITE}_ONCE
locking/rtmutex: Rename argument in the rt_mutex_adjust_prio_chain() documentation as well
locking/rwsem: Fix lock optimistic spinning when owner is not running
locking: Remove ACCESS_ONCE() usage
locking/rwsem: Check for active lock before bailing on spinning
locking/rwsem: Avoid deceiving lock spinners
locking/rwsem: Set lock ownership ASAP
locking/rwsem: Document barrier need when waking tasks
locking/futex: Check PF_KTHREAD rather than !p->mm to filter out kthreads
locking/mutex: Refactor mutex_spin_on_owner()
locking/mutex: In mutex_spin_on_owner(), return true when owner changes
This change adds the OPAL interface definitions to allow Linux to read,
write and erase from system flash devices. We register platform devices
for the flash devices exported by firmware.
We clash with the existing opal_flash_init function, which is really for
the FSP flash update functionality, so we rename that initcall to
opal_flash_update_init().
A future change will add an mtd driver that uses this interface.
Changes from Joel Stanley and Jeremy Kerr.
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Acked-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This moves the Cell platform to use the pci_controller_ops
structure rather than ppc_md for PCI controller operations.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This moves the Maple platform to use the pci_controller_ops
structure rather than ppc_md for PCI controller operations.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This moves the PaSemi platform to use the pci_controller_ops
structure rather than ppc_md for PCI controller operations.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This moves the PowerNV platform to use the pci_controller_ops
structure rather than ppc_md for PCI controller operations.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This moves the pSeries platform to use the pci_controller_ops structure,
rather than ppc_md for PCI controller operations.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This moves the Power Mac platform to use the pci_controller_ops
structure rather than ppc_md for PCI controller operations.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
If a pci_controller_ops struct is provided to iommu_init_early_dart,
populate that with the DMA setup ops, rather than ppc_md. If NULL is
provided, populate ppc_md as before.
This also patches the call sites for Maple and Power Mac to pass
NULL, so existing behaviour is preserved.
The benefit of making this optional is that it means we don't have
to change dart, Maple and Power Mac over to the controller_ops
system in one fell swoop.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
pcibios_enable_device_hook returned an int. Every implementation
returned either -EINVAL or 0. The return value wasn't propagated by
the caller: any non-zero return value caused pcibios_enable_device
to return -EINVAL itself. Therefore, make the hook return a bool.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Previously, find_and_init_phbs() was used in both PowerNV and pSeries
setup. However, since RTAS support has been dropped from PowerNV, we
can move it into a platform-specific file.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
smp_ops->probe() is currently supposed to return the number of cpus in
the system.
The last actual usage of the value was removed in May 2007 in e147ec8f18
"[POWERPC] Simplify smp_space_timers". We still passed the value around
until June 2010 when even that was finally removed in c1aa687d49
"powerpc: Clean up obsolete code relating to decrementer and timebase".
So drop that requirement, probe() now returns void, and update all
implementations.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The patch to add it_page_shift incorrectly changed the increment of
uaddr to use it_page_shift, rather then (1 << it_page_shift).
This broke booting on at least some Cell blades, as the iommu was
basically non-functional.
Fixes: 3a553170d3 ("powerpc/iommu: Add it_page_shift field to determine iommu page size")
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The conversion from __get_cpu_var() to this_cpu_ptr() in iic_setup_cpu()
is wrong. It causes an oops at boot.
We need the per-cpu address of struct cpu_iic, not cpu_iic.regs->prio.
Sparse noticed this, because we pass a non-iomem pointer to out_be64(),
but we obviously don't check the sparse results often enough.
Fixes: 69111bac42 ("powerpc: Replace __get_cpu_var uses")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The celleb code has seen no actual development for ~7 years.
We (maintainers) have no access to test hardware, and it is highly
likely the code has bit-rotted.
As far as we're aware the hardware was never widely available, and is
certainly no longer available, and no one on the list has shown any
interest in it over the years.
So remove it. If anyone has one and cares please speak up.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Jeremy Kerr <jk@ozlabs.org>
The powernv code has some conditional support for running on bare metal
machines that have no OPAL firmware, but provide RTAS.
No released machines ever supported that, and even in the lab it was
just a transitional hack in the days when OPAL was still being
developed.
So remove the code.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Freescale updates from Scott:
"Highlights include BMan device tree nodes, an MSI erratum workaround, a
couple minor performance improvements, config updates, and misc
fixes/cleanup."
The k(un)map function may be called in atomic context in the
function map_and_flush(), so use k(un)map_atomic to replace it,
else we would get the below warning during kdump:
BUG: sleeping function called from invalid context at include/linux/highmem.h:58
in_atomic(): 1, irqs_disabled(): 1, pid: 736, name: sh
INFO: lockdep is turned off.
irq event stamp: 0
hardirqs last enabled at (0): [< (null)>] (null)
hardirqs last disabled at (0): [<c000000000066d1c>] .copy_process.part.44+0x50c/0x1360
softirqs last enabled at (0): [<c000000000066d1c>] .copy_process.part.44+0x50c/0x1360
softirqs last disabled at (0): [< (null)>] (null)
CPU: 1 PID: 736 Comm: sh Tainted: G D W 3.10.62-ltsi-WR6.0.0.0_standard #2
Call Trace:
[c0000000f47cf120] [c00000000000b150] .show_stack+0x170/0x290 (unreliable)
[c0000000f47cf210] [c000000000b71334] .dump_stack+0x28/0x3c
[c0000000f47cf280] [c0000000000bb5d8] .__might_sleep+0x1a8/0x270
[c0000000f47cf310] [c0000000000440cc] .map_and_flush+0x4c/0xc0
[c0000000f47cf390] [c0000000000441cc] .mpc85xx_smp_machine_kexec+0x8c/0xec0
[c0000000f47cf420] [c00000000002ae00] .machine_kexec+0x60/0x90
[c0000000f47cf4b0] [c00000000010957c] .crash_kexec+0x8c/0x100
[c0000000f47cf6a0] [c000000000015df8] .die+0x348/0x450
[c0000000f47cf740] [c00000000002f3a0] .bad_page_fault+0xe0/0x130
[c0000000f47cf7c0] [c00000000001f3e4] storage_fault_common+0x40/0x44
Signed-off-by: Yanjiang Jin <yanjiang.jin@windriver.com>
[scottwood@freescale.com: fix subject line]
Signed-off-by: Scott Wood <scottwood@freescale.com>
This patch fixes a section mismatch warning
WARNING: vmlinux.o(.text+0x213b6): Section mismatch in reference from the function chrp_init_early() to the variable .init.data:boot_command_line
The function chrp_init_early() references
the variable __initdata boot_command_line.
This is often because chrp_init_early lacks a __initdata
annotation or the annotation of boot_command_line is wrong.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently, when a sensor value is read, the kernel calls OPAL, which in
turn builds a message for the FSP, and waits for a message back.
The new device tree for OPAL sensors [1] adds new sensors that can be
read synchronously (core temperatures for instance) and that don't need
to wait for a response.
This patch modifies the opal call to accept an OPAL_SUCCESS return value
and cover the case above.
[1] https://lists.ozlabs.org/pipermail/skiboot/2015-March/000639.html
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
OPAL has its own list of return codes. The patch provides a translation
of such codes in errnos for the opal_sensor_read call, and possibly
others if needed.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
If M64 has been supported, the prefetchable 64-bits memory resources
shouldn't be mapped to the corresponding PE# via M32DT. Unfortunately,
we're doing that in pnv_ioda_setup_pe_seg() wrongly. The issue was
introduced by commit 262af55 ("powerpc/powernv: Enable M64 aperatus
for PHB3"). The patch fixes the issue by simply skipping M64 resources
when updating to M32DT.
Cc: <stable@vger.kernel.org> # v3.17+
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In struct pci_dn, the pcidev field is assigned but not used, so remove it.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When IOV BAR is big, each is covered by 4 M64 windows. This leads to
several VF PE sits in one PE in terms of M64.
Group VF PEs according to the M64 allocation.
[bhelgaas: use dev_printk() when possible]
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
M64 aperture size is limited on PHB3. When the IOV BAR is too big, this
will exceed the limitation and failed to be assigned.
Introduce a different mechanism based on the IOV BAR size:
- if IOV BAR size is smaller than 64MB, expand to total_pe
- if IOV BAR size is bigger than 64MB, roundup power2
[bhelgaas: make dev_printk() output more consistent, use PCI_SRIOV_NUM_BARS]
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On PowerNV platform, resource position in M64 BAR implies the PE# the
resource belongs to. In some cases, adjustment of a resource is necessary
to locate it to a correct position in M64 BAR .
This patch adds pnv_pci_vf_resource_shift() to shift the 'real' PF IOV BAR
address according to an offset.
Note:
After doing so, there would be a "hole" in the /proc/iomem when offset
is a positive value. It looks like the device return some mmio back to
the system, which actually no one could use it.
[bhelgaas: rework loops, rework overlap check, index resource[]
conventionally, remove pci_regs.h include, squashed with next patch]
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Implement pcibios_iov_resource_alignment() on powernv platform.
On PowerNV platform, there are 3 cases for the IOV BAR:
1. initial state, the IOV BAR size is multiple times of VF BAR size
2. after expanded, the IOV BAR size is expanded to meet the M64 segment size
3. sizing stage, the IOV BAR is truncated to 0
pnv_pci_iov_resource_alignment() handle these three cases respectively.
[bhelgaas: adjust to drop "align" parameter, return pci_iov_resource_size()
if no ppc_md machdep_call version]
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On PHB3, PF IOV BAR will be covered by M64 BAR to have better PE isolation.
M64 BAR is a type of hardware resource in PHB3, which could map a range of
MMIO to PE numbers on powernv platform. And this range is divided equally
by the number of total_pe with each divided range mapping to a PE number.
Also, the M64 BAR must map a MMIO range with power-of-two size.
The total_pe number is usually different from total_VFs, which can lead to
a conflict between MMIO space and the PE number.
For example, if total_VFs is 128 and total_pe is 256, the second half of
M64 BAR will be part of other PCI device, which may already belong to other
PEs.
This patch prevents the conflict by reserving additional space for the PF
IOV BAR, which is total_pe number of VF's BAR size.
[bhelgaas: make dev_printk() output more consistent, index resource[]
conventionally]
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Previously the iommu_table had the same lifetime as a struct pnv_ioda_pe
and was embedded in it. The pnv_ioda_pe was assigned to a PE on the bootup
stage. Since PEs are based on the hardware layout which is static in the
system, they will never get released. This means the iommu_table in the
pnv_ioda_pe will never get released either.
This no longer works for VF PE. VF PEs are created and released dynamically
when VFs are created and released. So we need to assign pnv_ioda_pe to VF
PEs respectively when VFs are enabled and clean up those resources for VF
PE when VFs are disabled. And iommu_table is one of the resources we need
to handle dynamically.
Current iommu_table is a static field in pnv_ioda_pe, which will face a
problem when freeing it. During the disabling of a VF,
pnv_pci_ioda2_release_dma_pe will call iommu_free_table to release the
iommu_table for this PE. A static iommu_table will fail in
iommu_free_table.
According to these requirement, this patch allocates iommu_table
dynamically.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
pci_dn is the extension of PCI device node and is created from device node.
Unfortunately, VFs are enabled dynamically by PF's driver and they don't
have corresponding device nodes and pci_dn, which is required to access
VFs' config spaces.
The patch creates pci_dn for VFs in pcibios_sriov_enable() on their PF,
and removes pci_dn for VFs in pcibios_sriov_disable() on their PF. When
VF's pci_dn is created, it's put to the child list of the pci_dn of PF's
upstream bridge. The pci_dn is linked to pci_dev during early fixup time
to setup the fast path.
[bhelgaas: add ifdef around add_one_dev_pci_info(), use dev_printk()]
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We currently have a "special" syscall for switching endianness. This is
syscall number 0x1ebe, which is handled explicitly in the 64-bit syscall
exception entry.
That has a few problems, firstly the syscall number is outside of the
usual range, which confuses various tools. For example strace doesn't
recognise the syscall at all.
Secondly it's handled explicitly as a special case in the syscall
exception entry, which is complicated enough without it.
As a first step toward removing the special syscall, we need to add a
regular syscall that implements the same functionality.
The logic is simple, it simply toggles the MSR_LE bit in the userspace
MSR. This is the same as the special syscall, with the caveat that the
special syscall clobbers fewer registers.
This version clobbers r9-r12, XER, CTR, and CR0-1,5-7.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
During suspend/migration operation we must wait for the VASI state reported
by the hypervisor to become Suspending prior to making the ibm,suspend-me
RTAS call. Calling routines to rtas_ibm_supend_me() pass a vasi_state variable
that exposes the VASI state to the caller. This is unnecessary as the caller
only really cares about the following three conditions; if there is an error
we should bailout, success indicating we have suspended and woken back up so
proceed to device tree update, or we are not suspendable yet so try calling
rtas_ibm_suspend_me again shortly.
This patch removes the extraneous vasi_state variable and simply uses the
return code to communicate how to proceed. We either succeed, fail, or get
-EAGAIN in which case we sleep for a second before trying to call
rtas_ibm_suspend_me again. The behaviour of ppc_rtas() remains the same,
but migrate_store() now returns the propogated error code on failure.
Previously -1 was returned from migrate_store() in the failure case which
equates to -EPERM and was clearly wrong.
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Cc: Nathan Fontenont <nfont@linux.vnet.ibm.com>
Cc: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We currently read the information about idle states from the device
tree, so as to find out the CPU idle states supported by the platform.
Use the of_property_read/count_xxx() APIs, which handle endian
conversions for us, and mean we don't need any endian annotations in the
code.
Signed-off-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Provide an unregister interface for the opal message notifiers
to be called when not needed like during driver unload/remove.
Signed-off-by: Neelesh Gupta <neelegup@linux.vnet.ibm.com>
Reviewed-by: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Fixes the condition check of incoming message type which can
otherwise shoot beyond the message notifiers head array.
Signed-off-by: Neelesh Gupta <neelegup@linux.vnet.ibm.com>
Reviewed-by: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
Reviewed-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
