ibmtr_resume() is calling ibmtr_probe(), which is devinit. Whether
that's the right thing to do there is a separate question, but
since it's PCMCIA and thus will never compile without HOTPLUG...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ixgbe_init_interrupt_scheme() is called from ixgbe_resume(). Build that
with CONFIG_PM and without CONFIG_HOTPLUG and you've got a problem.
Several helpers called by it also are misannotated __devinit.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* rackmeter_remove() reference needs devexit_p
* rackmeter_setup() is calls devinit and is called only from devinit
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
PCI side of driver should be devinit, not init
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
switch to __init for those; unlike powerpc sparc has no hotplug support
for that stuff and their ->probe() tends to call __init functions while
being declared __devinit.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The code
if (shost->dma_channel != NO_ISA_DMA)
free_dma(shost->dma_channel);
in there is triggerable only if we have CONFIG_ISA (we only set ->dma_channel to
something other than NO_ISA_DMA under #ifdef CONFIG_ISA). OTOH, free_dma() is
not guaranteed to be there in absense of CONFIG_ISA. IOW, driver runs into
undefined symbols on PCI-but-not-ISA configs (e.g. on frv) and it's a false
positive.
Fix: put the entire if () under #ifdef CONFIG_ISA; behaviour doesn't change and
dependency on free_dma() disappears for !CONFIG_ISA.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Uses clk_...() a lot
Acked-by: rmk+kernel@arm.linux.org.uk
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
icside_register_v[56] is called from (__devinit) icside_probe
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
talitos_remove() can be called from talitos_probe() on failure
exit path, so it can't be __devexit.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
stli_findeisabrds() and stli_initbrds() are using __init and called only
from __init.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
One fail path in hrz_probe omitted device disable. Fix it.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An intermediate transition from _RUNNING to _IN_SHUTDOWN could have been
missed by the former code.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
If there is more than one FireWire controller present, dummy_zero_addr
and dummy_max_addr were added multiple times to different lists, thus
corrupting the lists. Fix this by allocating them dynamically per host
instead of just once globally.
(Perhaps a better address space allocation algorithm could rid us of the
two dummy address spaces.)
Fixes http://bugzilla.kernel.org/show_bug.cgi?id=10129 .
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Commit 7ff93f8b ("mlx4_core: Multiple port type support") introduced
support for different port types. As part of that support, SET_PORT
is invoked to set the port type during driver startup. However, as a
side-effect, for IB ports the invocation of this command also sets the
port's capability mask to zero (losing the default value set by FW).
To fix this, get the default ib port capabilities (via a MAD_IFC Port
Info query) during driver startup, and save them for use in the
mlx4_SET_PORT command when setting the port-type to Infiniband.
This patch fixes problems with subnet manager (SM) failover such as
<https://bugs.openfabrics.org/show_bug.cgi?id=1183>, which occurred
because the IsTrapSupported bit in the capability mask was zeroed.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
the toshiba ACPI driver will, in a failure case, free the rfkill state
before stopping the polling timer that would use this state. More interesting,
in the same failure case handling, it calls the exit function, which also
frees the rfkill state, but after stopping the polling.
If the race happens, a NULL pointer is passed to rfkill_force_state()
which then causes a nice dereference.
Fix the race by just not doing the too-early freeing of the rfkill state.
This appears to be the cause of a hot issue on kerneloops.org; while I
have no solid evidence of that this patch will fix the issue, the race
appears rather real.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
i2c clients should be removed in reverse order compared to the probe
(actually: bind) order. This matters when several clients depend on
each other.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Build fixes for isp1301_omap; no behavior changes:
- fix incorrect probe() signature (it changed many months ago)
- provide missing functions on H3 and H4 boards
- "sparse" fixes (static, NULL-vs-0)
The H3 build bits subset some of the stuff that was previously in
the OMAP tree but never went to mainline.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
While parsing 'hid_blacklist' in the apple alu wireless keyboard is not found.
This happens because in the blacklist it is declared with HID_USB_DEVICE
although the keyboards are really bluetooth devices. The same holds for
'apple_devices' list.
This patch fixes it by changing HID_USB_DEVICE to HID_BLUETOOTH_DEVICE in those
two lists.
Signed-off-by: Jan Scholz <Scholz@fias.uni-frankfurt.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The patch fixes following build error:
CC drivers/mtd/nand/fsl_upm.o
drivers/mtd/nand/fsl_upm.c: In function 'fun_chip_init':
drivers/mtd/nand/fsl_upm.c:168: warning: passing argument 2 of 'of_mtd_parse_partitions' from incompatible pointer type
drivers/mtd/nand/fsl_upm.c:168: warning: passing argument 3 of 'of_mtd_parse_partitions' from incompatible pointer type
drivers/mtd/nand/fsl_upm.c:168: error: too many arguments to function 'of_mtd_parse_partitions'
make[1]: *** [drivers/mtd/nand/fsl_upm.o] Error 1
The breakage was introduced in 69fd3a8d09
("[MTD] remove unused mtd parameter in of_mtd_parse_partitions()").
While at it, also add a check for the of_mtd_parse_partitions() return
value.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Linux will continue to ignore OSI(Linux),
except for a white-list containing a few systems.
So delete the black-list,
and stop soliciting user-feedback on the console.
Signed-off-by: Len Brown <len.brown@intel.com>
This fixes a regression from v2.6.27, caused by commit
5814f737e1cd2cfa2893badd62189acae3e1e1fd, "ACPI: thinkpad-acpi:
attempt to preserve fan state on resume".
It is possible for fan_suspend() to fail to properly initialize
fan_control_desired_level as required by fan_resume(), resulting on
the fan always being set to level 7 on resume if the user didn't
touch the fan controller.
In order to get fan sleep/resume handling to work right:
1. Fix the fan_suspend handling of the T43 firmware quirk. If it is
still undefined, we didn't touch the fan yet and that means we have no
business doing it on resume.
2. Store the fan level on its own variable to avoid any possible
issues with hijacking fan_control_desired_level (which isn't supposed
to have anything other than 0-7 in it, anyway).
3. Change the fan_resume code to me more straightforward to understand
(although we DO optimize the boolean logic there, otherwise it looks
disgusting).
4. Add comments to help understand what the code is supposed to be
doing.
5. Change fan_set_level to be less strict about how auto and
full-speed modes are requested.
http://bugzilla.kernel.org/show_bug.cgi?id=11982
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Reported-by: Tino Keitel <tino.keitel@tikei.de>
Signed-off-by: Len Brown <len.brown@intel.com>
PAUSE frames are only relevant for the real device, broadcasting them
to all macvlan devices can cause a significant load increase.
Reported-by: Ben Greear <greearb@candelatech.com>
Tested-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no need to print "Sony: " just after "sony-laptop: " (DRV_PFX).
Signed-off-by: Alessandro Guido <ag@alessandroguido.name>
Signed-off-by: Len Brown <len.brown@intel.com>
After commit 540b8bb9c3:
sony-laptop: fingers off backlight if video.ko is serving this functionality
I can't set brightness on my sony laptop (nothing in /sys/class/backlight).
dmesg says "sony-laptop: Sony: Brightness ignored, must be controlled by ACPI
video driver".
The function acpi_video_backlight_support returns 0 if we should use the
vendor-specific backlight support, while non-0 if the ACPI generic should
be used. Because of this, the check introduced by the said commit appears
reversed.
Signed-off-by: Alessandro Guido <ag@alessandroguido.name>
Signed-off-by: Len Brown <len.brown@intel.com>
Some Apple boxes evidently require us to set SCI_EN on resume
directly, because if we don't do that, they hung somewhere in the
resume code path. Moreover, on these boxes it is not sufficient to
use acpi_enable() to turn ACPI on during resume. All of this is
against the ACPI specification which states that (1) the BIOS is
supposed to return from the S3 sleep state with ACPI enabled
(SCI_EN set) and (2) the SCI_EN bit is owned by the hardware and we
are not supposed to change it.
For this reason, blacklist the affected systems so that the SCI_EN
bit is set during resume on them.
[NOTE: Unconditional setting SCI_EN for all system on resume doesn't
work, because it makes some other systems crash (that's to be
expected). Also, it is not entirely clear right now if all of the
Apple boxes require this workaround.]
This patch fixes the recent regression tracked as
http://bugzilla.kernel.org/show_bug.cgi?id=12038
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Tested-by: Tino Keitel <tino.keitel@gmx.de>
Tested-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Now I know why I had strange "scheduling in atomic" problems:
acpi_evaluate_integer() does malloc(..., irqs_disabled() ? GFP_ATOMIC
: GFP_KERNEL)... which is (of course) broken.
There's no way to reliably tell if we need GFP_ATOMIC or not from
code, this one for example fails to detect spinlocks held.
Fortunately, allocation seems small enough to be done on stack.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Acked-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
ACPI battery interface reports its state either in mW or in mA, and
discharge rate in your case is reported in mW. power_supply interface
does not have such a parameter, so current_now parameter is used
for all cases. But in case of mW, reported discharge should
be converted into mA.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Tested-by: Ferenc Wagner <wferi@niif.hu>
Signed-off-by: Len Brown <len.brown@intel.com>
physmap_flash_remove releases only last memory region. This causes
memory leak if multiple resources were provided.
This patch fixes this leakage by using devm_ functions.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This fixes broken terminology added in the "m25p80.c erase enhance" patch,
which added a chip erase command but called it "block erase". There are
already two block erase commands; blocks are 4KiB or 32KiB. There's also
a sector erase (usually 64 KiB). Chip erase typically covers Megabytes.
OPCODE_BE ==> OPCODE_CHIP_ERASE
erase_block ==> erase_chip
[dbrownell@users.sourceforge.net: update sector erase comments too ]
Signed-off-by: Chen Gong <clumsycg@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Commit d0e8c47c58 ("m25p80.c extended jedec
support") added support for extended ids but seems to break on flashes
which don't have an extended id defined. If the table does not have an
extid defined, then we should ignore it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Michael Hennerich <Michael.Hennerich@analog.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Commit d0e8c47c58 ("m25p80.c extended jedec
support") added support for extended ids but in the process managed to
break detection of all flashes.
The ext jedec id check was inserted into an if statement that lacked
braces, and it did not add the required braces. As such, the detection
routine always returns the first entry in the SPI flash list.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Include <linux/dma-mapping.h> and <linux/io.h>, not files from <asm/*>
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
It fixes suspend/resume failure of xf86-video-intel dri2
branch. As dri2 branch doesn't call I830DRIResume() to restore
hardware status page anymore, we need to preserve
this register across suspend/resume.
Signed-off-by: Peng Li <peng.li@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
hp-plus uses 8390p.c, so it should use eip_poll(), not ei_poll().
drivers/built-in.o: In function `hpp_probe1':
hp-plus.c:(.init.text+0x9cbd): undefined reference to `ei_poll'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ath5k driver has too many interrupts per second at idle
http://bugzilla.kernel.org/show_bug.cgi?id=11749
Signed-off-by: Martin Xu <martin.xu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We should only tell the hardware its capable of DMA'ing
to us only what we asked dev_alloc_skb(). Prior to this
it is possible a large RX'd frame could have corrupted
DMA data but for us but we were saved only because we
were previously also pci_map_single()'ing the same large
value. The issue prior to this though was we were unmapping
a smaller amount which the prior DMA patch fixed.
Signed-off-by: Bennyam Malavazi <Bennyam.Malavazi@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This should fix the SW-IOMMU bounce buffer starvation
seen ok kernel.org bugzilla 11811:
http://bugzilla.kernel.org/show_bug.cgi?id=11811
Users on MacBook Pro 3.1/MacBook v2 would see something like:
DMA: Out of SW-IOMMU space for 4224 bytes at device 0000:0b:00.0
Unfortunately its only easy to trigger on MacBook Pro 3.1/MacBook v2
so far so its difficult to debug (even with swiotlb=force).
We were pci_unmap_single()'ing less bytes than what we called
for with pci_map_single() and as such we were starving
the swiotlb from its 64MB amount of bounce buffers. We remain
consistent and now always use sc->rxbufsize for RX. While at
it we update the beacon DMA maps as well to only use the data
portion of the skb, previous to this we were pci_map_single()'ing
more data for beaconing than what we tell the hardware it can use,
therefore pushing more iotlb abuse.
Still not sure why this is so easily triggerable on
MacBook Pro 3.1, it may be the hardware configuration
tends to use more memory > 3GB mark for DMA.
Signed-off-by: Maciej Zenczykowski <zenczykowski@gmail.com>
Signed-off-by: Bennyam Malavazi <Bennyam.Malavazi@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For the RX DMA fix for iwlwifi ("iwlagn: fix RX skb alignment") Luis
pointed out:
> aligned_dma_addr can obviously be > real_dma_addr at this point, what
> guarantees we can use it on our own whim?
I asked around, and he's right, there may be platforms that do not allow
passing such such an address to the DMA API functions. This patch
changes it by using the proper dma_sync_single_range_for_cpu API
invented for this purpose.
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add another model ID of a broken firmware to prevent early I/O errors
by acesses at the end of the disk. Reported at linux1394-user,
http://marc.info/?t=122670842900002
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Add another model ID of a broken firmware to prevent early I/O errors
by acesses at the end of the disk. Reported at linux1394-user,
http://marc.info/?t=122670842900002
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
PHY is mostly compatible with the existing VSC8244 PHY. The init sequence
is different and the interrupt mask lacks some bits present in the VSC8244.
Rather than making a copy of the existing VSC234x config_intr function and
change one constant, I modify it to select the interrupt mask based on
which driver is calling it. This lets it be used by both drivers.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently the omap McBSP code was cleaned up to get rid of
direct McBSP register tinkering by the drivers. Looks like
lcd_sx1.c never got converted, and now it breaks builds.
It seems the lcd_sx1.c driver is attempting SPI mode, but
doing it in a different way compared to omap_mcbsp_set_spi_mode().
Remove the broken driver, patches welcome to add it back when
done properly by patching both mcbsp.c and lcd_sx1.c.
Cc: Vovan888@gmail.com
Cc: linux-fbdev-devel@lists.sourceforge.net
Signed-off-by: Tony Lindgren <tony@atomide.com>
drm vblank initialization keeps track of the changes in driver-supplied
frame counts across vt switch and mode setting, but only if you let it by
not tearing down the drm vblank structure.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Before we had the notion of pinning objects, we had a kludge around to make
sure all of the objects were still resident in the GTT before we committed
to executing a batch buffer. We don't need this any longer, and it sticks an
error return in the middle of object domain computations that must be
associated with a subsequent flush/invalidate emmission into the ring.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Because we write pipestat before iir, it's possible that a pipestat
interrupt will occur between the pipestat write and the iir write. This
leaves pipestat with an interrupt status not visible in iir. This may cause
an interrupt flood as we never clear the pipestat event.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The old code was wandering through the active list looking for pinned
buffers; there may be other pinned buffers around. Fortunately, we keep a
count of the total amount of pinned memory and can use that instead.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Instead, just warn that bad things are happening and do our best to clean up
the mess without the GPU's help.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The IMR masking was a technique recommended for avoiding getting stuck with
no interrupts generated again in MSI mode. It kept new IIR bits from getting
set between the IIR read and the IIR write, which would have otherwise
prevented an MSI from ever getting generated again. However, this caused a
problem for vblank as the IMR mask would keep the pipe event interrupt from
getting reflected in IIR, even after the IMR mask was brought back down.
Instead, just check the state of IIR after we ack the interrupts we're going
to handle, and restart if we didn't get IIR all the way to zero.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The pipestat fields affect reporting of all vblank-related interrupts, so we
have to reset them during the irq_handler, and while enabling vblank
interrupts. Otherwise, if a pipe status field had been set to non-zero
before enabling reporting, we would never see an interrupt again.
This patch adds i915_enable_pipestat and i915_disable_pipestat to abstract
out the steps needed to change the reported interrupts.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
ml_ff_playback() uses spin_(un)lock_bh. However this function is
called with interrupts disabled from erase_effect() in
drivers/input/ff-core.c:196.
This is not permitted, and will result in a WARN_ON in the bottom
half handling code. This patch changes this function to just use
spin_lock_irqsave() instead, solving the problem and simplifying
the locking logic.
This was reported as entry #106559 in kerneloops.org
Reported-by: kerneloops.org
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
New firmware image brings enhanced tuning performance.
Firmware is available for download at the following location:
http://www.steventoth.net/linux/sms1xxx
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The video device was part of the gspca device. On device disconnection
while streaming, the device structure is freed at close time.
In this case, the remaining close job on the video device run out of
allocated memory.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The previous subdriver protection against rmmod was done via the
file operations table in the device descriptor. On device disconnection
while streaming, the device structure was freed at close time, and the
module_put still used the module name in the freed area.
Now, explicit module get/put are done on open and close.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As a side effect, the sd routine stop0 is called on disconnect.
This permits the subdriver to free its resources.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
remove redundant argument comments in files of drivers/net/*
Signed-off-by: Qinghuang Feng <qhfeng.kernel@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
the use of is_blah() suggests a 1 or 0 return. This assumption is made in
pxa25x_udc code such as:
dev->vbus = is_vbus_present();
where dev->vbus is a bitfield. This fix allows pxa25x_udc_probe to correctly
detect vbus. Other changes were to make its use consistent in the rest of
the code.
Signed-off-by: Jaya Kumar <jayakumar.lkml@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It causes recursive locking warning and is unneeded after
introduction of STARTED flag.
* Resume vs. stop is effectively solved by DISCONNECT flag.
* No problem in suspend vs. start -- urb is submitted even after open
which is possible after connect which is called after start.
* Resume vs. start solved by STARTED flag.
* Suspend vs. stop -- no problem in killing urb and timer twice.
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fix hp-plus driver link errors.
Builds as loadable module and kernel image driver.
All drivers that use 8390.o or 8390p.o that will build on
i386 with MCA/PCI/EISA/ISA were built successfully both
=m and =y.
drivers/built-in.o: In function `hpp_open':
hp-plus.c:(.text+0xac06c): undefined reference to `eip_interrupt'
hp-plus.c:(.text+0xac0d7): undefined reference to `eip_open'
drivers/built-in.o: In function `hpp_close':
hp-plus.c:(.text+0xac1bb): undefined reference to `eip_close'
drivers/built-in.o: In function `hpp_probe1':
hp-plus.c:(.init.text+0xa98a): undefined reference to `NS8390p_init'
drivers/built-in.o: In function `hp_plus_probe':
(.init.text+0xa9fe): undefined reference to `__alloc_eip_netdev'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hi,
after noticing that my Netgear FA411 (PCMCIA-NIC) [1] stopped working with
the release of the 2.6.25 kernel (sidux-version), I checked the
respective driver sources and noticed that the pcnet_cs driver bailed
out with "use axnet_cs instead" for the Netgear FA411, but axnet_cs
doesn't claim this ID.
I compiled a kernel with the PCMCIA-ID for the netgear card moved to
axnet_cs from pcnet_cs which worked. I then contacted sidux-kernel
maintainer Stefan Lippers-Hollmann who turned the info into this patch
and integrated it into the kernel:
<http://svn.berlios.de/svnroot/repos/fullstory/linux-sidux-2.6/trunk/debian/patches/features/2.6.27.4_PCMCIA_move-PCMCIA-ID-for-Netgear-FA411-from-pcnet_cs-to-axnet_cs.patch>
This works for me and AFAIK there were no reports of any breakage for
other devices on sidux-support.
This looks like a trivial patch, but since I have very limited
experience with kernel modifications I might be woefully wrong there.
But if there are no side effects of this patch, is it possible to get it
into the official kernel?
I can provide more detailed information on the affected hardware if
necessary.
-cord
[1]
Socket 1 Device 0: [axnet_cs] (bus ID: 1.0)
Configuration: state: on
Product Name: NETGEAR FA411 Fast Ethernet
Identification: manf_id: 0x0149 card_id: 0x0411
function: 6 (network)
prod_id(1): "NETGEAR" (0x9aa79dc3)
prod_id(2): "FA411" (0x40fad875)
prod_id(3): "Fast Ethernet" (0xb4be14e3)
prod_id(4): --- (---)
From: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Date: Sat, 1 Nov 2008 23:53:04 +0000
Subject: PCMCIA: move PCMCIA ID for Netgear FA411 from pcnet_cs to axnet_cs:
Since kernel 2.6.25, commit 61da96be07
(pcnet_cs: if AX88190-based card, printk "use axnet_cs instead" message.),
pcnet_cs bails out with "use axnet_cs instead" for the Netgear FA411, but
axnet_cs doesn't claim this ID.
Socket 1 Device 0: [axnet_cs] (bus ID: 1.0)
Configuration: state: on
Product Name: NETGEAR FA411 Fast Ethernet
Identification: manf_id: 0x0149 card_id: 0x0411
function: 6 (network)
prod_id(1): "NETGEAR" (0x9aa79dc3)
prod_id(2): "FA411" (0x40fad875)
prod_id(3): "Fast Ethernet" (0xb4be14e3)
prod_id(4): --- (---)
Cc: stable <stable@kernel.org> [2.6.25, 2.6.26, 2.6.27]
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Signed-off-by: Cord Walter <qord@cwalter.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changes:
- remove locks, rtc class provides them
- remove unused include
- if the rtc can't handle set_time, the driver should not fake it
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the following I/O controller hubs:
ICH7DH, ICH9M, ICH9M-E, ICH10, ICH10R, ICH10D and ICH10DO.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The iTCO_wdt code was not clearing the correct bits.
It now clears the timeout status bit and then the
SECOND_TO_STS bit and then the BOOT_STS bit.
Note: we should first clear the SECOND_TO_STS bit
before clearing the BOOT_STS bit.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Bugzilla #9868: On Intel motherboards with the ICH9 based I/O controllers
(Like DP35DP and DG33FB) the iTCO timer counts but it doesn't reboot the
system after the counter expires.
This patch fixes this by moving the enabling & disabling of the TCO_EN bit
in the SMI_EN register into the start and stop code.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Using spin_lock_irqsave with a local variable called flags without
declaring is a bad idea, fix this by declaring it.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch fixes the case when the phy_ids is mostly Fs and in some case 0x0
due to broken hardware.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 5330/1: mach-pxa: Fixup reset for systems using reboot=cold or other strings
[ARM] pxa: fix incorrect PCMCIA PSKTSEL pin configuration for spitz
[ARM] pxa: fix I2C controller device being registered twice on Akita
pxafb: only initialize the smart panel thread when dealing with a smartpanel
pxafb: introduce LCD_TYPE_MASK and use it.
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: ACE1001 patch for cp2101.c
USB: usbmon: fix read(2)
USB: gadget rndis: send notifications
USB: gadget rndis: stop windows self-immolation
USB: storage: update unusual_devs entries for Nokia 5300 and 5310
USB: storage: updates unusual_devs entry for the Nokia 6300
usb: musb: fix bug in musb_schedule
USB: fix SB700 usb subsystem hang bug
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (23 commits)
net: fix tiny output corruption of /proc/net/snmp6
atl2: don't request irq on resume if netif running
ipv6: use seq_release_private for ip6mr.c /proc entries
pkt_sched: fix missing check for packet overrun in qdisc_dump_stab()
smc911x: Fix printf format typo in smc911x driver.
asix: Fix asix-based cards connecting to 10/100Mbs LAN.
mv643xx_eth: fix recycle check bound
mv643xx_eth: fix the order of mdiobus_{unregister, free}() calls
sh: sh_eth: Update to change of mii_bus
TPROXY: supply a struct flowi->flags argument in inet_sk_rebuild_header()
TPROXY: fill struct flowi->flags in udp_sendmsg()
net: ipg.c fix bracing on endian swapping
phylib: Fix auto-negotiation restart avoidance
net: jme.c rxdesc.flags is __le16, other missing endian swaps
phylib: fix phy name example in documentation
net: Do not fire linkwatch events until the device is registered.
phonet: fix compilation with gcc-3.4
ixgbe: fix compilation with gcc-3.4
pktgen: fix multiple queue warning
net: fix ip_mr_init() error path
...
Newer versions of hald tries to open it to call QUERYCAP.
Due to the lack of a proper locking, it is possible to open the device
before it finishes initialization.
This patch adds a lock to avoid this risk, and to protect the list of
em28xx devices.
While here, remove the uneeded BKL lock.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Don't reconnect device in the USB-bus. Reconnect command was not
executed every time by device firmware and that causes harm.
Reconnection is not needed so remove it.
Signed-off-by: Jose Alberto Reguero <jareguero@telefonica.net>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now that we have a polling task for IR, there's a race condition, since
IR can be polling while other operations are being doing. Also, we are
now sharing the same urb_buf for both read and write control urb
operations. So, we need a mutex.
Thanks to Davin Heitmueller <devin.heitmueller@gmail.com> for warning me.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Before this patch, every register setup on em28xx were dynamically
allocating a temporary buffer for control URB's to be handled.
To avoid this ping-pong, use, instead a pre-allocated buffer.
Also, be sure that read control URB's also use the buffer, instead of
relying on a stack buffer.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
em28xx_init_dev() has some error conditions that are not properly
de-allocating dev var, nor freeing the device number for a future usage.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In commit a96d6ef34, the mouse interfaces on the unibody macbooks were
put into hid mouse ignore list. This was a little bit too premature
though, as the corresponding bcm5974 changes are scheduled for 2.6.29.
Remove these devices from the ignore list for now, in order to provide at
least basic functionality with the HID driver.
Will be reintroduced in 2.6.29
Reported-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add AX_MEDIUM_ENCK also when speed = 10/100Mbps. This allows my belkin
f5d5055 to work with my 100Mbps switch and with an old 10Mbps ISA card.
Without this patch, the card is recognized and the interface is brought
up fine, but no packets actually flow through the interface.
Signed-off-by: Pantelis Koukousoulas <pktoss@gmail.com>
Acked-by: David Hollis <dhollis@davehollis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When mv643xx_eth allocates skbuffs, it adds
'dma_get_cache_alignment() - 1' to the length it needs, so that it can
align the skb's ->data pointer to a cache boundary. When checking
whether a transmitted skbuff can be reused as a receive buffer, these
bytes needs to be included into the minimum bound for the recycle check.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update to change of mii_bus interface and fix some warning.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch which adds IDs for AKTAKOM USB->RS232 cable
(http://www.aktakom.ru/product/kio/ace-1001.htm) is attached.
From: M Kondrin <mkondrin@hppi.troitsk.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There's a bug in the usbmon binary reader: When using read() to fetch
the packets and a packet's data is partially read, the next read call
will once again return up to len_cap bytes of data. The b_read counter
is not regarded when determining the remaining chunk size.
So, when dumping USB data with "cat /dev/usbmon0 > usbmon.trace" while
reading from a USB storage device and analyzing the dump file
afterwards it will get out of sync after a couple of packets.
Signed-off-by: Ingo van Lil <inguin@gmx.de>
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It turns out that atomic_inc_return() returns the *new* value
not the original one, so the logic in rndis_response_available()
kept the first RNDIS response notification from getting out.
This prevented interoperation with MS-Windows (but not Linux).
Fix this to make RNDIS behave again.
Signed-off-by: Richard Röjfors <richard.rojfors@endian.se>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Somewhere in the conversion of the RNDIS gadget code to the new
framework, the descriptor of its data interface seems to have
been copied from the CDC Ethernet driver. Unfortunately that
means it got a nonzero altsetting ... which is incorrect. Issue
uncovered by Richard Röjfors <richard.rojfors@endian.se>.
This patch fixes that problem, and resolves at least some cases
of Windows XP bluescreening itself.
Tested-by: Richard Röjfors <richard.rojfors@endian.se>.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1168) updates the unusual_devs entry for the Nokia 5300.
According to Jorge Lucangeli Obes <t4m5yn@gmail.com>, some existing
models have a revision number lower than the lower limit of the
current entry.
The patch also moves the entry for the Nokia 5310 to its correct place
in the file.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1169) modifies the unusual_devs entry for the Nokia
6300. According to Maciej Gierok <mgierok@gmail.com> and David
McBride <dwm@doc.ic.ac.uk>, the revision limits need to be wider.
This fixes Bugzilla #11768.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This bug was introduced recently. Fix it before bigger
problems appear.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch is required for AMD SB700 south bridge revision A12 and A13 to avoid
USB subsystem hang symptom. The USB subsystem hang symptom is observed when the
system has multiple USB devices connected to it. In some cases a USB hub may be
required to observe this symptom.
This patch works around the problem by correcting the internal register setting
that will help by changing the behavior of the internal logic to avoid the
USB subsystem hang issue. The change in the behavior of the logic does not
impact the normal operation of the USB subsystem.
Reported-by: Volker Armin Hemmann <volker.armin.hemmann@tu-clausthal.de>
Tested-by: Volker Armin Hemmann <volker.armin.hemmann@tu-clausthal.de>
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Libin Yang <libin.yang@amd.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: more general identifier for Phoenix BIOS
AMD IOMMU: check for next_bit also in unmapped area
AMD IOMMU: fix fullflush comparison length
AMD IOMMU: enable device isolation per default
AMD IOMMU: add parameter to disable device isolation
x86, PEBS/DS: fix code flow in ds_request()
x86: add rdtsc barrier to TSC sync check
xen: fix scrub_page()
x86: fix es7000 compiling
x86, bts: fix unlock problem in ds.c
x86, voyager: fix smp generic helper voyager breakage
x86: move iomap.h to the new include location
Fix printk format warnings when CCISS_DEBUG is defined.
drivers/block/cciss.c:2856: warning: format '%d' expects type 'int', but argument 2 has type 'long unsigned int'
drivers/block/cciss.c:3205: warning: format '%x' expects type 'unsigned int', but argument 2 has type 'long unsigned int'
drivers/block/cciss.c:3236: warning: format '%x' expects type 'unsigned int', but argument 2 has type '__u64'
drivers/block/cciss.c:3246: warning: format '%x' expects type 'unsigned int', but argument 2 has type '__u64'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Mike Miller <mike.miller@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
OMAP LDP boot crash. This is because w1 subsystem changed the search
interface, so update omap_hdq's search interface to follow the change.
Signed-off-by: Stanley.Miao <stanley.miao@windriver.com>
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
One more error handling code should have kfree as well
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Eric Miao <eric.miao@marvell.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After commit a1d35a7a (cirrusfb: use modedb and add mode_option
parameter), these variables are no longer used, so remove them to fix
compilation warning.
Signed-off-by: Vlada Periæ <vlada.peric@gmail.com>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In order to analyze the SMC of the newer MacPros, applesmc needs to
recognize the machine. This patch adds the missing generic dmi_match
entry for MacPro models.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Error handling code following a kzalloc should free the allocated data.
The semantic match that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r exists@
local idexpression x;
statement S;
expression E;
identifier f,l;
position p1,p2;
expression *ptr != NULL;
@@
(
if ((x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...)) == NULL) S
|
x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
)
<... when != x
when != if (...) { <+...x...+> }
x->f = E
...>
(
return \(0\|<+...x...+>\|ptr\);
|
return@p2 ...;
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Mike Rapoport <mike@compulab.co.il>
Cc: Richard Purdie <rpurdie@linux.intel.com>
Cc: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix unsafe order in dma mapping operation: always flush data from the
cache *BEFORE* invalidating it, to allow full duplex transfers where the
same buffer may be used for both writes and reads.
Signed-off-by: Andrea Paterniani <a.paterniani@swapp-eng.it>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The LCD driver core calls LCD drivers when either the blanking state or
the display mode has changed, but does not make any check to see if the
called driver has a .set_mode method.
This means if a driver only has a .set_power method then the system will
OOPS on changing mode (and with the console semaphore held so you cannot
easily see the problem).
Fix the problem by ensuring that either callback is valid before use.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixes a data corruption bug in pxa2xx_spi.c when operating in full duplex
mode with DMA and using buffers that overlap.
SPI transmit and receive buffers are allowed to be the same or to overlap.
However, this driver fails if such overlap is attempted in DMA mode
because it maps the rx and tx buffers in the wrong order. By mapping
DMA_FROM_DEVICE (read) before DMA_TO_DEVICE (write), it invalidates the
cache before flushing it, thus discarding data which should have been
transmitted.
The patch corrects the order of mapping. This bug exists in all versions
of pxa2xx_spi.c; similar bugs are in the drivers for two other SPI
controllers (au1500, imx).
A version of this patch has been tested on kernel 2.6.20 using
verification of loopback data with: random transfer length, random
bits-per-word, random positive offsets (both larger and smaller than
transfer length) between the start of the rx and tx buffers, and varying
clock rates.
Signed-off-by: Ned Forrester <nforrester@whoi.edu>
Cc: Vernon Sauder <vernoninhand@gmail.com>
Cc: J. Scott Merritt <merrij3@rpi.edu>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: <stable@kernel.org> [2.6.27.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Restore support for compiling tmiofb with acceleration disabled.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Enable -D DEBUG in the GRU Makefile if CONFIG_SGI_GRU_DEBUG is selected.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are already various drivers having bigger label than 12 bytes. Most
of them fit well under 20 bytes but make column width exact so that
oversized labels don't mess up output alignment.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Acked-by: David Brownell <david-b@pacbell.net>
Cc: <stable@kernel.org> [2.6.26.x, 2.6.26.x, 2.6.27.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When booting in a direct color mode, the penguin has dirty feet, i.e.,
some pixels have the wrong color. This is caused by
fb_set_logo_directpalette() which does not initialize the last 32 palette
entries.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The error test that follows the call to backlight_device_register semms
not to concern the right variable.
A simplified version of the semantic match that finds this problem is
as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@def0@
expression x;
position p0;
@@
x@p0 = backlight_device_register(...)
@protected@
expression def0.x,E;
position def0.p0;
position p;
statement S;
@@
x@p0
... when != x = E
if (!IS_ERR(x) && ...) {<... x@p ...>} else S
@unprotected@
expression def0.x;
identifier fld;
position def0.p0;
position p != protected.p;
@@
x@p0
... when != x = E
* x@p->fld
// </smpl>
Signed-off-by: Julien Brunel <brunel@diku.dk>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add temperature sensor support for iMac 6.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Tested-by: Caleb Hyde <caleb.hyde@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
rxfd->frag_info is a __le64, IPG_RFI_FRAGLEN is a cpu-endian
constant and wants to be outside of the le64_to_cpu. Fixed
in multiple places.
Also an occurrence where le64_to_cpu was used instead of cpu_to_le64
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A previous patch, 51e2a3846e, made
genphy_config_aneg() not restart aneg by calling genphy_restart_aneg() if
the advertisement hadn't changed.
But, genphy_restart_aneg() doesn't just restart aneg, it may also *enable*
aneg or un-isolate the PHY from the MII (those functions are controlled by
the same register). The code to avoid calling genphy_restart_aneg() didn't
consider this.
So, modify genphy_config_aneg() to also check if the PHY needs to have aneg
enabled or be un-isolated before deciding not to restart aneg.
This caused a problem with certain Davicom PHYs, as that driver isolates
the PHY (why?) before calling genphy_config_aneg() and expects the PHY to
be un-isolated by that function.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Reported-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the minimal patch to fix endian mismatches. These are
probably bugs on big-endian arches, noops on little endian.
jme_rxsum_ok could be improved to directly take a __le16 and
change all of the masks/sets to be in little-endian, but
has not been done here to keep the patch small.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CC [M] drivers/net/ixgbe/ixgbe_main.o
drivers/net/ixgbe/ixgbe_main.c: In function `ixgbe_intr':
drivers/net/ixgbe/ixgbe_main.c:1290: sorry, unimplemented: inlining failed in call to 'ixgbe_irq_enable': function body not available
drivers/net/ixgbe/ixgbe_main.c:1312: sorry, unimplemented: called from here
make[4]: *** [drivers/net/ixgbe/ixgbe_main.o] Error 1
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before initialization, dev->irq may be zero. Make sure we don't disable
it at reset time in that case.
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Impact: cleanup
I got the following warnings on IA64:
linux-2.6/drivers/pci/intel-iommu.c: In function 'init_dmars':
linux-2.6/drivers/pci/intel-iommu.c:1658: warning: format '%Lx' expects type 'long long unsigned int', but argument 2 has type 'u64'
linux-2.6/drivers/pci/intel-iommu.c:1663: warning: format '%Lx' expects type 'long long unsigned int', but argument 2 has type 'u64'
Another victim of int-ll64.h versus int-l64.h confusion between platforms.
->reg_base_addr has a type of u64 - which can only be printed out
consistently if we cast its type up to LL.
[ Eventually reg_base_addr should be converted to phys_addr_t, for which
we have the %pR printk helper - but that is out of the scope of late
-rc's. ]
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
So I dug deeper into the DMA problems I had with iwlagn and a kind soul
helped me in that he said something about pci-e alignment and mentioned
the iwl_rx_allocate function to check for crossing 4KB boundaries. Since
there's 8KB A-MPDU support, crossing 4k boundaries didn't seem like
something the device would fail with, but when I looked into the
function for a minute anyway I stumbled over this little gem:
BUG_ON(rxb->dma_addr & (~DMA_BIT_MASK(36) & 0xff));
Clearly, that is a totally bogus check, one would hope the compiler
removes it entirely. (Think about it)
After fixing it, I obviously ran into it, nothing guarantees the
alignment the way you want it, because of the way skbs and their
headroom are allocated. I won't explain that here nor double-check that
I'm right, that goes beyond what most of the CC'ed people care about.
So then I came up with the patch below, and so far my system has
survived minutes with 64K pages, when it would previously fail in
seconds. And I haven't seen a single instance of the TX bug either. But
when you see the patch it'll be pretty obvious to you why.
This should fix the following reported kernel bugs:
http://bugzilla.kernel.org/show_bug.cgi?id=11596http://bugzilla.kernel.org/show_bug.cgi?id=11393http://bugzilla.kernel.org/show_bug.cgi?id=11983
I haven't checked if there are any elsewhere, but I suppose RHBZ will
have a few instances too...
I'd like to ask anyone who is CC'ed (those are people I know ran into
the bug) to try this patch.
I am convinced that this patch is correct in spirit, but I haven't
understood why, for example, there are so many unmap calls. I'm not
entirely convinced that this is the only bug leading to the TX reply
errors.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Before ieee80211_notify_mac() was added, it was presented with the
use case of using it to tell mac80211 that the association may
have been lost because the firmware crashed/reset.
Since then, it has also been used by iwlwifi to (slightly) speed
up re-association after resume, a workaround around the fact that
mac80211 has no suspend/resume handling yet. It is also not used
by any other drivers, so clearly it cannot be necessary for "good
enough" suspend/resume.
Unfortunately, the callback suffers from a severe problem: It only
works for station mode. If suspend/resume happens while in IBSS or
any other mode (but station), then the callback is pointless.
Recently, it has created a number of locking issues, first because
it required rtnl locking rather than RCU due to calling sleeping
functions within the critical section, and now because it's called
by iwlwifi from the mac80211 workqueue that may not use the rtnl
because it is flushed under rtnl.
(cf. http://bugzilla.kernel.org/show_bug.cgi?id=12046)
I think, therefore, that we should take a step back, remove it
entirely for now and add the small feature it provided properly.
For suspend and resume we will need to introduce new hooks, and for
the case where the firmware was reset the driver will probably
simply just pretend it has done a suspend/resume cycle to get
mac80211 to reprogram the hardware completely, not just try to
connect to the current AP again in station mode. When doing so, we
will need to take into account locking issues and possibly defer
to schedule_work from within mac80211 for the resume operation,
while the suspend operation must be done directly.
Proper suspend/resume should also not necessarily try to reconnect
to the current AP, the time spent in suspend may have been short
enough to not be disconnected from the AP, mac80211 will detect
that the AP went out of range quickly if it did, and if the
association is lost then the AP will disassoc as soon as a data
frame is sent. We might also take into account WWOL then, and
have mac80211 program the hardware into such a mode where it is
available and requested.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
skb->tail can't be meant here because it's not the same across 32/64 bit
compilations. This means there's no way the current driver can work on
64-bit architectures.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org [2.6.27]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We should release old elevator when change to use a new one.
Signed-off-by: Zhao Lei <zhaolei@cn.fujitsu.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Impact: fix guest kernel crash with CONFIG_XEN_SCRUB_PAGES=y
Jens noticed that scrub_page() has a buggy unmap of the wrong
thing. (virtual address instead of page)
Linus pointed out that the whole scrub_page() code is an unnecessary
reimplementation of clear_highpage() to begin with.
Just use clear_highpage() rather than reimplementing it poorly.
Reported-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (27 commits)
rtnetlink: propagate error from dev_change_flags in do_setlink()
isdn: remove extra byteswap in isdn_net_ciscohdlck_slarp_send_reply
Phonet: refuse to send bigger than MTU packets
e1000e: fix IPMI traffic
e1000e: fix warn_on reload after phy_id error
phy: fix phy address bug
e100: fix dma error in direction for mapping
igb: use dev_printk instead of printk
qla3xxx: Cleanup: Fix link print statements.
igb: Use device_set_wakeup_enable
e1000: Use device_set_wakeup_enable
e1000e: Use device_set_wakeup_enable
via-velocity: enable perfect filtering for multicast packets
phy: Add support for Marvell 88E1118 PHY
mlx4_en: Pause parameters per port
phylib: fix premature freeing of struct mii_bus
atl1: Do not enumerate options unsupported by chip
atl1e: fix broken multicast by removing unnecessary crc inversion
gianfar: Fix DMA unmap invocations
net/ucc_geth: Fix oops in uec_get_ethtool_stats()
...
commit a144ea4b7a [IPV4]: annotate struct in_ifaddr
Missed this extra byteswap as the isdn inlines hide the htonl inside
put_u32 which causes an extra byteswap on little-endian arches.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some users reported that they have machines with BMCs enabled that cannot
receive IPMI traffic after e1000e is loaded.
http://marc.info/?l=e1000-devel&m=121909039127414&w=2http://marc.info/?l=e1000-devel&m=121365543823387&w=2
This fixes the issue if they load with the new parameter = 0 by disabling
crc stripping, but leaves the performance feature on for most users.
Based on work done by Hong Zhang.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the driver fails to initialize the first time due to the failure in the
phy_id check the kernel triggers a warn_on on the second try to load the
driver because the driver did not free the msi/x resources in the first
load because of the previous failure in phy_id check.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The format for reading the IR controller changed in firmware 1.20. It now
provides the events on bulk endpoint 1 instead of using a control request.
Support the new format, providing backward compatibility for users who might
be using older firmware.
Thanks to Patrick Boettcher <patrick.boettcher@desy.de> for providing the
required information on how the version 1.20 firmware works.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Noticed by sparse:
drivers/media/video/s2255drv.c:2531:6: warning: restricted __le32 degrades to integer
Cc: Dean Anderson <dean@sensoray.com>
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It is not safe to assume that the i2c gate will be open before issuing the
command to power down the tuner. In fact, many demods only open the gate
long enough to issue the tuning command.
This fix allows power management to work properly for those tuners behind an
i2c gate (in my case the problem was with the HVR-950Q)
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The attached patch makes the em28xx auxillary audio input work.
Tested with the HVR-950.
em28xx: make auxillary audio input work
The tuner audio input was working but the aux input wasn't. Tested with
the HVR-950.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
ATSC should be considered a legacy delivery system, or else fields such as
p->u.vsb.modulation do not get populated (resulting in set_frontend failures)
Cc: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix misplaced quirk entries for devices driven by hid-pl driver. The
devices shouls be only blacklisted by generic HID driver, not completely
ignored.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The vendor BSP used for the WM8350 development provided an I2C driver
which incorrectly returned zero on succesful sends rather than the
number of transmitted bytes, an error which was then propagated into the
WM8350 I2C accessors.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Commit 0794469da3: ("ACPI: struct device -
replace bus_id with dev_name(), dev_set_name()") introduced a bug by
testing 'dev_name(ldev)' instead of 'ldev->bus' for NULL when printing
out the bus information.
So if ldev->bus was NULL, we'd oops.
Reported-and-tested-by: Bruno Prémont <bonbons@linux-vserver.org>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Len Brown <len.brown@intel.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Close possible infinite loop with interrupts off when devices are
added back to the starved list.
Fixes: http://bugzilla.kernel.org/show_bug.cgi?id=11898
Reported-by: <alex.shi@intel.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
PHYID returns 0xffff and not 0xffffffff when not found and in some
case(at91sam9263) 0x0. Maybe this patch could be useful.
Signed-off-by: Giulio Benetti <giulio.benetti@micronovasrl.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The e100 driver triggers BUG_ON(buf->direction != dir)
by doing pci_map_single(..., PCI_DMA_BIDIRECTIONAL)
and pci_dma_sync_single_for_device(..., PCI_DMA_TODEVICE).
Changing the DMA direction, especially with dmabounce will result
in unexpected behaviour.
Reported-by: Anders Grafstrom <grfstrm@users.sourceforge.net>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use dev_printk() instead of printk() to give a little more context
and use consistent format.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removed debug print statements and improved conditionals around informational statements.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since dev->power.should_wakeup bit is used by the PCI core to
decide whether the device should wake up the system from sleep
states, set/unset this bit whenever WOL is enabled/disabled using
igb_set_wol(). Accordingly, use device_can_wakeup() for checking
if wake-up is supported by the device.
Signed-off-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since dev->power.should_wakeup bit is used by the PCI core to
decide whether the device should wake up the system from sleep
states, set/unset this bit whenever WOL is enabled/disabled using
e1000_set_wol(). Accordingly, use device_can_wakeup() for checking
if wake-up is supported by the device.
Signed-off-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since dev->power.should_wakeup bit is used by the PCI core to
decide whether the device should wake up the system from sleep
states, set/unset this bit whenever WOL is enabled/disabled using
e1000_set_wol(). Accordingly, use device_can_wakeup() for checking
if wake-up is supported by the device.
Signed-off-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: don't grab devices with no input
HID: fix radio-mr800 hidquirks
HID: fix kworld fm700 radio hidquirks
HID: fix start/stop cycle in usbhid driver
HID: use single threaded work queue for hid_compat
HID: map macbook keys for "Expose" and "Dashboard"
HID: support for new unibody macbooks
HID: fix locking in hidraw_open()
This patch will add support for the Marvell 88E1118 PHY which supports gigabit ethernet among other things.
Signed-off-by: Ron Madrid <ron_madrid@sbcglobal.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before the change the driver reported the same pause parameters
for all the ports, even only one of them was modified.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
The file(s) below do not use LINUX_VERSION_CODE nor KERNEL_VERSION.
drivers/hwmon/lis3lv02d.c
This patch removes the said #include <version.h>.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'sh/for-2.6.28' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
serial: sh-sci: Reorder the SCxTDR write after the TDxE clear.
sh: __copy_user function can corrupt the stack in case of exception
sh: Fixed the TMU0 reload value on resume
sh: Don't factor in PAGE_OFFSET for valid_phys_addr_range() check.
sh: early printk port type fix
i2c: fix i2c-sh_mobile rx underrun
sh: Provide a sane valid_phys_addr_range() to prevent TLB reset with PMB.
usb: r8a66597-hcd: fix wrong data access in SuperH on-chip USB
fix sci type for SH7723
serial: sh-sci: fix cannot work SH7723 SCIFA
sh: Handle fixmap TLB eviction more coherently.
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
V4L/DVB (9624): CVE-2008-5033: fix OOPS on tvaudio when controlling bass/treble
V4L/DVB (9623): tvaudio: Improve debug msg by printing something more human
V4L/DVB (9622): tvaudio: Improve comments and remove a unneeded prototype
V4L/DVB (9621): Avoid writing outside shadow.bytes[] array
V4L/DVB (9620): tvaudio: use a direct reference for chip description
V4L/DVB (9619): tvaudio: update initial comments
V4L/DVB (9618): tvaudio: add additional logic to avoid OOPS
V4L/DVB (9617): tvtime: remove generic_checkmode callback
V4L/DVB (9616): tvaudio: cleanup - group all callbacks together
V4L/DVB (9615): tvaudio: instead of using a magic number, use ARRAY_SIZE
V4L/DVB (9613): tvaudio: fix a memory leak
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] dpt_i2o: fix transferred data length for scsi_set_resid()
[SCSI] scsi_error regression: Fix idempotent command handling
[SCSI] zfcp: Fix hexdump data in s390dbf traces
[SCSI] zfcp: fix erp timeout cleanup for port open requests
[SCSI] zfcp: Wait for port scan to complete when setting adapter online
[SCSI] zfcp: Fix cast warning
[SCSI] zfcp: Fix request list handling in error path
[SCSI] zfcp: fix mempool usage for status_read requests
[SCSI] zfcp: fix req_list_locking.
[SCSI] zfcp: Dont clear reference from SCSI device to unit
[SCSI] qla2xxx: Update version number to 8.02.01-k9.
[SCSI] qla2xxx: Return a FAILED status when abort mailbox-command fails.
[SCSI] qla2xxx: Do not honour max_vports from firmware for 2G ISPs and below.
[SCSI] qla2xxx: Use pci_disable_rom() to manipulate PCI config space.
[SCSI] qla2xxx: Correct Atmel flash-part handling.
[SCSI] megaraid: fix mega_internal_command oops
m68k allmodconfig:
| drivers/misc/c2port/core.c: In function 'c2port_reset':
| drivers/misc/c2port/core.c:73: error: dereferencing pointer to incomplete type
| drivers/misc/c2port/core.c: In function 'c2port_strobe_ck':
| drivers/misc/c2port/core.c:91: error: dereferencing pointer to incomplete type
Include <linux/sched.h> to fix it, as m68k's local_irq_enable() needs to know
about struct task_struct.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
dpt_i2o.c::adpt_i2o_to_scsi() reads the value at (reply+5) which
should contain the length in bytes of the transferred data. This
would be correct if reply was a u32 *. However it is a void * here,
so we need to read the value at (reply+20) instead.
The value at (reply+5) is usually 0xff0000, which is apparently
'large enough' and didn't cause any trouble until 2.6.27 where
commit 427e59f09f
Author: James Bottomley <James.Bottomley@HansenPartnership.com>
Date: Sat Mar 8 18:24:17 2008 -0600
[SCSI] make use of the residue value
caused this to become visible through e.g. iostat -x .
Signed-off-by: Miquel van Smoorenburg <mikevs@xs4all.net>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
- simplified code
- use platform_driver_probe
- removed locking: it's provided by rtc subsystem
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently libata uses four methods to detect device presence.
1. PHY status if available.
2. TF register R/W test (only promotes presence, never demotes)
3. device signature after reset
4. IDENTIFY failure detection in SFF state machine
Combination of the above works well in most cases but recently there
have been a few reports where a phantom device causes unnecessary
delay during probe. In both cases, PHY status wasn't available. In
one case, it passed #2 and #3 and failed IDENTIFY with ATA_ERR which
didn't qualify as #4. The other failed #2 but as it passed #3 and #4,
it still caused failure.
In both cases, phantom device reported diagnostic failure, so these
cases can be safely worked around by considering any !ATA_DRQ IDENTIFY
failure as NODEV_HINT if diagnostic failure is set.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit 46abc02175 ("phylib: give mdio
buses a device tree presence") added a call to device_unregister() in
a situation where the caller did not intend for the device to be
freed yet, but apart from just unregistering the device from the
system, device_unregister() does an additional put_device() that is
intended to free it.
The right function to use in this situation is device_del(), which
unregisters the device from the system like device_unregister() does,
but without dropping the reference count an additional time.
Bug report from Bryan Wu <cooloney@kernel.org>.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Tested-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Of the various WOL options provided in include/linux/ethtool.h, the
L1 NIC supports only magic packet. Remove all options except magic
packet from the atl1 driver.
Signed-off-by: Jay Cliburn <jcliburn@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Inverting the crc after calling ether_crc_le() is unnecessary and breaks
multicast. Remove it.
Tested-by: David Madore <david.madore@ens.fr>
Signed-off-by: Jay Cliburn <jcliburn@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
We weren't unmapping DMA memory, which will break when gianfar gets used
on systems with more than 32-bits of memory. Also, it's just plain wrong.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
p_{tx,rx}_fw_statistics_pram are special: they're available only when
a device is open. If the device is closed, we should just fill the data
with zeroes.
Fixes the following oops:
root@b1:~# ifconfig eth1 down
root@b1:~# ethtool -S eth1
Unable to handle kernel paging request for data at address 0x00000000
Faulting instruction address: 0xc01e1dcc
Oops: Kernel access of bad area, sig: 11 [#1]
[...]
NIP [c01e1dcc] uec_get_ethtool_stats+0x98/0x124
LR [c0287cc8] ethtool_get_stats+0xfc/0x23c
Call Trace:
[cfaadde0] [c0287ca8] ethtool_get_stats+0xdc/0x23c (unreliable)
[cfaade20] [c0288340] dev_ethtool+0x2fc/0x588
[cfaade50] [c0285648] dev_ioctl+0x290/0x33c
[cfaadea0] [c0272238] sock_ioctl+0x80/0x2ec
[cfaadec0] [c00b5ae4] vfs_ioctl+0x40/0xc0
[cfaadee0] [c00b5fa8] do_vfs_ioctl+0x78/0x20c
[cfaadf10] [c00b617c] sys_ioctl+0x40/0x74
[cfaadf40] [c00142d8] ret_from_syscall+0x0/0x38
[...]
---[ end trace b941007b2dfb9759 ]---
Segmentation fault
p.s. While at it, also remove u64 casts, they aren't needed.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This driver is pretty mature, and the worst of the known
problems has been fixed (the 32-bit failures due to readq
implementation).
So let's finally give it a version of 1.0
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the Sun CP3260 ATCA blade which is
a N2 based ATCA blade with 2 NIU ports. The NIU ports do not
have on-board PHY.
Signed-off-by: Santwona Behera <santwona.behera@sun.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create Documentation/blockdev/ sub-directory and populate it.
Populate the Documentation/serial/ sub-directory.
Move MSI-HOWTO.txt to Documentation/PCI/.
Move ioctl-number.txt to Documentation/ioctl/.
Update all relevant 00-INDEX files.
Update all relevant Kconfig files and source files.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
This patch is a bug fix to the SystemACE driver to use resource_size_t
for physical address instead of unsigned long. This makes the driver
work correctly on 32 bit systems with 64-bit resources (e.g. PowerPC 440).
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The logging of sense data for fatal errors was accidentally removed
during Hyper PAV implementation.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In ccw_device_move_to_orphanage(), a replacing ccw_device
is searched via get_{disc,orphaned}_ccwdev_by_dev_id()
which obtain a reference on the returned ccw_device.
This reference must be given up again after the device
has been moved to its new parent.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The current virtio model on s390 has the descriptor page above the main
memory. The guest virtio detection will oops if the mem= parameter is
used to reduce/change the memory size.
We have to use real_memory_size instead of max_pfn to detect the virtio
descriptor pages.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Various printk format string in code used by the Xilinx Virtex platform
are not 32-bit/64-bit safe. Add correct casting to fix the bugs.
Reported-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
