Nothing was using the method and there isn't any need for this hook. This
leaves smp_cpus_done() empty for the moment.
As suggested by Paul Bolle <pebolle@tiscali.nl>.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
XLP9XX has 20 cores per node, opposed to 8 on earlier XLP8XX.
Update code that calculates node id from cpu id to handle this.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6283/
Panic() is going to add a \n itself and it's annoying if a panic message rolls
of the screen on a device with no scrollback.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The config7/config4 register has to be written on all the threads.
This does not cause any problems in XLP, but is needed for XLPII
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5700/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
commit 3747069b25e419f6b51395f48127e9812abc3596 upstream.
The __cpuinit type of throwaway sections might have made sense
some time ago when RAM was more constrained, but now the savings
do not offset the cost and complications. For example, the fix in
commit 5e427ec2d0 ("x86: Fix bit corruption at CPU resume time")
is a good example of the nasty type of bugs that can be created
with improper use of the various __init prefixes.
After a discussion on LKML[1] it was decided that cpuinit should go
the way of devinit and be phased out. Once all the users are gone,
we can then finally remove the macros themselves from linux/init.h.
Note that some harmless section mismatch warnings may result, since
notify_cpu_starting() and cpu_up() are arch independent (kernel/cpu.c)
and are flagged as __cpuinit -- so if we remove the __cpuinit from
the arch specific callers, we will also get section mismatch warnings.
As an intermediate step, we intend to turn the linux/init.h cpuinit
related content into no-ops as early as possible, since that will get
rid of these warnings. In any case, they are temporary and harmless.
Here, we remove all the MIPS __cpuinit from C code and __CPUINIT
from asm files. MIPS is interesting in this respect, because there
are also uasm users hiding behind their own renamed versions of the
__cpuinit macros.
[1] https://lkml.org/lkml/2013/5/20/589
[ralf@linux-mips.org: Folded in Paul's followup fix.]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5494/
Patchwork: https://patchwork.linux-mips.org/patch/5495/
Patchwork: https://patchwork.linux-mips.org/patch/5509/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Move the nlm_cpu_ready[] array used by the cpu wakeup code to the
boot area, along with rest of the boot parameter code.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5425/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This moves the calculation and casting needed to access the CPU initialization
data to a function nlm_get_boot_data()
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5426/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The core initialization and reset vector setup needs to be done
even when booting uniprocessor. Move this code from smp.c to setup.c
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5428/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use standard function to print cpumask. Also fixup the name of the
variable used and make it static.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/5024/
Acked-by: John Crispin <blogic@openwrt.org>
Provide functions ack_c0_eirr(), set_c0_eimr(), clear_c0_eimr()
and read_c0_eirr_and_eimr() that do the EIMR and EIRR operations
and update the interrupt handling code to use these functions.
Also, use the EIMR register functions to mask interrupts in the
irq code.
The 64-bit interrupt request and mask registers (EIRR and EIMR) are
accessed when the interrupts are off, and the common operations are
to set or clear a bit in these registers. Using the 64-bit c0 access
functions for these operations is not optimal in 32-bit, because it
will disable/restore interrupts and split/join the 64-bit value during
each register access.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4790/
Signed-off-by: John Crispin <blogic@openwrt.org>
On XLR/XLS, the cpu cores communicate with fast on-chip devices
(e.g. network accelerator, security engine etc.) using the Fast
Messaging Network(FMN). The FMN queues and credits needs to be
configured and intialized before it can be used.
The co-processor 2 on XLR/XLS CPU cores has registers for FMN access,
and the XLR/XLS has custom instructions for sending and loading
messages. The FMN can deliver also per-cpu interrupts when messages
are available at the CPU.
This patch adds FMN initialization, adds interrupt setup and handling,
and also provides support for sending and receiving FMN messages.
Signed-off-by: Ganesan Ramalingam <ganesanr@broadcom.com>
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4468
Signed-off-by: John Crispin <blogic@openwrt.org>
Create struct nlm_pic_irq for interrupts handled by the PIC.
This simplifies IRQ handling for multi-SoC as well as
the single SoC cases. Also split the setup of percpu and PIC
interrupts so that we can configure the PIC interrupts for
every node.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4467
Signed-off-by: John Crispin <blogic@openwrt.org>
Upto 4 Netlogic XLP SoCs can be connected over ICI links to form a
coherent multi-node system. Each SoC has its own set of on-chip
devices including PIC. To support this, add a per SoC stucture and
use it for the PIC and SYS block addresses instead of using global
variables.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4469
Signed-off-by: John Crispin <blogic@openwrt.org>
Initial code to support more than 32 cpus. The platform CPU mask
is updated from 32-bit mask to cpumask_t. Convert places that use
cpu_/cpus_ functions to use cpumask_* functions.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4464
Signed-off-by: John Crispin <blogic@openwrt.org>
The cpuid was not passed into early_init_secondary even though the
comment indicated that it will be. Fix this.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4458
Signed-off-by: John Crispin <blogic@openwrt.org>
This has been obsolescent for a while; time for the final push.
In adjacent context, replaced old cpus_* with cpumask_*.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: David S. Miller <davem@davemloft.net> (arch/sparc)
Acked-by: Chris Metcalf <cmetcalf@tilera.com> (arch/tile)
Cc: user-mode-linux-devel@lists.sourceforge.net
Cc: Russell King <linux@arm.linux.org.uk>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: linux-hexagon@vger.kernel.org
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Helge Deller <deller@gmx.de>
Cc: sparclinux@vger.kernel.org
Netlogic XLR chip has multiple cores. Each core includes four integrated
hardware threads, and they share L1 data and instruction caches.
If the chip is marked to be SMT capable, scheduler then could do more, say,
idle load balancing.
Changes are now confined only to the code of XLR, and hardware is probed
to get core ID for correct setup.
[jayachandranc: simplified and adapted for new merged XLR/XLP code]
Signed-off-by: Hillf Danton <dhillf@gmail.com>
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2972/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Create a common NMI and reset handler in smpboot.S and use this for
both XLR and XLP. In the earlier code, the woken up CPUs would
busy wait until released, switch this to wakeup by NMI.
The initial wakeup code or XLR and XLP are differ since they are
started from different bootloaders (XLP from u-boot and XLR from
netlogic bootloader). But in both platforms the woken up CPUs wait
and are released by sending an NMI.
Add support for starting XLR and XLP in 1/2/4 threads per core.
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2970/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
- Update common files to support XLP.
- Add arch/mips/include/asm/netlogic/xlp-hal for register definitions
and access macros
- Add arch/mips/netlogic/xlp/ for XLP specific files.
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2967/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
- Move code that can be shared with XLP (irq.c, smp.c, time.c and
xlr_console.c) to arch/mips/netlogic/common
- Add asm/netlogic/haldefs.h and asm/netlogic/common.h for common and
io functions shared with XLP
- remove type 'nlm_reg_t *' and use uint64_t for mmio offsets
- Move XLR specific code in smp.c to xlr/wakeup.c
- Move XLR specific PCI code from irq.c to mips/pci/pci-xlr.c
- Provide API for pic functions called from common/irq.c
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2964/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2011-12-07 22:04:55 +00:00
Renamed from arch/mips/netlogic/xlr/smp.c (Browse further)
