Add support for the QSPI controller found some on Freescale/Motorola
Coldfire MCUs.
Full duplex, active high cs, spi modes 0-3 and word sizes 8-16 bits are
supported. The hardware drives the MISO, MOSI and SCLK lines, but the chip
selects are managed via GPIO and must be configured by the board code.
The QSPI controller has an 80 byte buffer which allows us to transfer up to 16
words at a time. For transfers longer than 16 words, we split the buffer in
half so we can update in one half while the controller is operating on the
other half. Interrupt latencies then ultimately limits our sustained thru-put
to something less than half the maximum speed supported by the part.
Signed-off-by: Steven King <sfking@fdwdc.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The match_table field of the struct of_device_id is constant
in <linux/of_platform.h> so it is worth to make the initialization
data constant.
The semantic match that finds this kind of pattern is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
disable decl_init,const_decl_init;
identifier I1, I2, x;
@@
struct I1 {
...
const struct I2 *x;
...
};
@s@
identifier r.I1, y;
identifier r.x, E;
@@
struct I1 y = {
.x = E,
};
@c@
identifier r.I2;
identifier s.E;
@@
const struct I2 E[] = ... ;
@depends on !c@
identifier r.I2;
identifier s.E;
@@
+ const
struct I2 E[] = ...;
// </smpl>
Signed-off-by: Márton Németh <nm127@freemail.hu>
Cc: Julia Lawall <julia@diku.dk>
Cc: cocci@diku.dk
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds support for a SPI master driver for the
DaVinci series of SOCs
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Philby John <pjohn@in.mvista.com>
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
/sys/bus/pci/drivers/megaraid_sas/poll_mode_io defaults to being
world-writable, which seems bad (letting any user affect kernel driver
behavior).
This turns off group and user write permissions, so that on typical
production systems only root can write to it.
Signed-off-by: Bryn M. Reeves <bmr@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are two copies of list_sort() in the tree already, one in the DRM
code, another in ubifs. Now XFS needs this as well. Create a generic
list_sort() function from the ubifs version and convert existing users
to it so we don't end up with yet another copy in the tree.
Signed-off-by: Dave Chinner <david@fromorbit.com>
Acked-by: Dave Airlie <airlied@redhat.com>
Acked-by: Artem Bityutskiy <dedekind@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: retry link resume if necessary
ata_piix: enable 32bit PIO on SATA piix
sata_promise: don't classify overruns as HSM errors
* master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: Ensure ARMv6/7 mm files are built using appropriate assembler options
ARM: Fix wrong dmb
ARM: 5874/1: serial21285: fix disable_irq-from-interrupt-handler deadlock
ARM: 5873/1: ARM: Fix the reset logic for ARM RealView boards
ARM: 5872/1: ARM: include needed linux/cpu.h in asm/cpu.h
ARM: 5871/1: arch/arm: Fix build failure for lpd7a404_defconfig caused by missing includes
ARM: 5870/1: arch/arm: Fix build failure for defconfigs without CONFIG_ISA_DMA_API set
ARM: 5868/1: ARM: fix "BUG: using smp_processor_id() in preemptible code"
ARM: 5867/1: Update U300 defconfig
ARM: 5866/1: arm ptrace: use unsigned types for kernel pt_regs
[ARM] pxa: fix strange characters in zaurus gpio .desc
ARM: add missing recvmmsg syscall number
[ARM] pxa: fix compiler warnings of unused variable 'id' in cpu_is_pxa9*()
[ARM] pxa: update pwm_backlight->notify() to include missed 'struct device *'
[ARM] pxa: enable L2 if present in XSC3
[ARM] pxa: do not enable L2 after MMU is enabled
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (56 commits)
sky2: Fix oops in sky2_xmit_frame() after TX timeout
Documentation/3c509: document ethtool support
af_packet: Don't use skb after dev_queue_xmit()
vxge: use pci_dma_mapping_error to test return value
netfilter: ebtables: enforce CAP_NET_ADMIN
e1000e: fix and commonize code for setting the receive address registers
e1000e: e1000e_enable_tx_pkt_filtering() returns wrong value
e1000e: perform 10/100 adaptive IFS only on parts that support it
e1000e: don't accumulate PHY statistics on PHY read failure
e1000e: call pci_save_state() after pci_restore_state()
netxen: update version to 4.0.72
netxen: fix set mac addr
netxen: fix smatch warning
netxen: fix tx ring memory leak
tcp: update the netstamp_needed counter when cloning sockets
TI DaVinci EMAC: Handle emac module clock correctly.
dmfe/tulip: Let dmfe handle DM910x except for SPARC on-board chips
ixgbe: Fix compiler warning about variable being used uninitialized
netfilter: nf_ct_ftp: fix out of bounds read in update_nl_seq()
mv643xx_eth: don't include cache padding in rx desc buffer size
...
Fix trivial conflict in drivers/scsi/cxgb3i/cxgb3i_offload.c
Interestingly, when SIDPR is used in ata_piix, writes to DET in
SControl sometimes get ignored leading to detection failure. Update
sata_link_resume() such that it reads back SControl after clearing DET
and retry if it's not clear.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: fengxiangjun <fengxiangjun@neusoft.com>
Reported-by: Jim Faulkner <jfaulkne@ccs.neu.edu>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit 871af1210f enabled 32bit PIO for
PATA piix but didn't for SATA. There's no reason not to use 32bit PIO
on SATA piix. Enable it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When sata_promise encounters an overrun or underrun error it
translates that to a libata AC_ERR_HSM, causing a hard reset.
Since over/under-runs were thought to be rare and transient,
this action seemed reasonable.
Unfortunately it turns out that the controller throws overrun
errors when e.g. hal polls a CD or DVD writer containing blank
media, causing long sequences of hard resets and retries before
EH finally gives up.
This patch updates sata_promise to classify over/under-runs as
AC_ERR_OTHER instead. This allows libata EH and upper layers to
retry or fail the operation as they see fit without the disruption
caused by repeated hard resets.
This fixes a problem using a DVD-RAM drive with sata_promise,
reported by Thomas Schorpp. I also tested it on a DVD-RW drive.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Tested-by: thomas schorpp <thomas.schorpp@googlemail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
During TX timeout procedure dev could be awoken too early, e.g. by
sky2_complete_tx() called from sky2_down(). Then sky2_xmit_frame()
can run while buffers are freed causing an oops. This patch fixes it
by adding netif_device_present() test in sky2_tx_complete().
Fixes: http://bugzilla.kernel.org/show_bug.cgi?id=14925
With debugging by: Mike McCormack <mikem@ring3k.org>
Reported-by: Berck E. Nash <flyboy@gmail.com>
Tested-by: Berck E. Nash <flyboy@gmail.com>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the panel's probe had failed, omapfb would still go on, eventually
crashing.
A better fix would be to handle each display properly, and leaving just
the failed display out. But that is a bigger change.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
If the scaling ratio is below 0.5 video output width can't be identical
to the display width. Reject such settings.
Signed-off-by: Ville Syrjälä <ville.syrjala@nokia.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
* 'agp-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/agp-2.6:
agp/hp: fail gracefully if we don't find an IOC
agp/hp: fixup hp agp after ACPI changes
agp: correct missing cleanup on error in agp_add_bridge
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (45 commits)
drm/nv04: Fix set_operation software method.
drm/nouveau: initialise DMA tracking parameters earlier
drm/nouveau: use dma.max rather than pushbuf size for checking GET validity
drm/nv04: differentiate between nv04/nv05
drm/nouveau: Fix null deref in nouveau_fence_emit due to deleted fence
drm/nv50: prevent a possible ctxprog hang
drm/nouveau: have ttm's fault handler called directly
drm/nv50: restore correct cache1 get/put address on fifoctx load
drm/nouveau: create function for "dealing" with gpu lockup
drm/nouveau: remove unused nouveau_channel_idle() function
drm/nouveau: fix handling of fbcon colours in 8bpp
drm/nv04: Context switching fixes.
drm/nouveau: Use the software object for fencing.
drm/nouveau: Allocate a per-channel instance of NV_SW.
drm/nv50: make the blocksize depend on vram size
drm/nouveau: better alignment of bo sizes and use roundup instead of ALIGN
drm/nouveau: Don't skip card take down on nv0x.
drm/nouveau: Implement nv42-nv43 TV load detection.
drm/nouveau: Clean up the nv17-nv4x load detection code a bit.
drm/nv50: fix fillrect color
...
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
menu: use proper 64 bit math
The new menu governor is incorrectly doing a 64 bit divide. Compile
tested only
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Previously enabled poll(2) support on one edge was never reconfigured when
sysfs polarity change was triggered from kernel, because 'struct device
*dev' shadowed an earlier definition.
Found by sparse, which I should've run much earlier.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The main bug was that 'blk_cleanup_queue()' was called while the block
device could still be in use, for example, because the card was removed
while files were still open.
In addition, to be sure that 'mmc_request()' will get called for all new
requests (so it can error them out), the queue is emptied during cleanup.
This is done after the worker thread is stopped to avoid racing with it.
Finally, it is not a device error for this to be happening, so quiet the
(sometimes very many) error messages.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Cc: <linux-mmc@vger.kernel.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If mmc_blk_set_blksize() fails mmc_blk_probe() the request queue and its
thread have been set up and they need to be shut down properly before
putting the disk.
Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Cc: <linux-mmc@vger.kernel.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When a card is removed before mmc_blk_probe() has called add_disk(), then
the minor field is uninitialized and has value 0. This caused
mmc_blk_put() to always release devidx 0 even if 0 was still in use. Then
the next mmc_blk_probe() used the first free idx of 0, which oopses in
sysfs, since it is used by another card.
Signed-off-by: Anna Lemehova <EXT-Anna.Lemehova@nokia.com>
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Cc: <linux-mmc@vger.kernel.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Warning(drivers/base/power/main.c:453): No description found for parameter 'dev'
Warning(drivers/base/power/main.c:453): No description found for parameter 'cb'
Warning(drivers/base/power/main.c:719): No description found for parameter 'dev'
Warning(drivers/base/power/main.c:719): No description found for parameter 'state'
Warning(drivers/base/power/main.c:719): No description found for parameter 'cb'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The console hangs during bootup when disable_irq is called from the
transmit interrupt handler (it will wait forever for it's "own"
interrupt in synchronize_irq). Fix by using disable_irq_nosync()
instead.
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Loops checking for certain condition were rather inconsistent.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Reported-by: Juha Leppanen <juha_motorsportcom@luukku.com>
Fixes bug causing VRFB memory area to be released twice.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Reported-by: Eino-Ville Talvala <talvala@stanford.edu>
Trivial patch which adds the __init/__exit macros to the module_init/
module_exit functions of
drivers/video/omap/lcd_htcherald.c
Please have a look at the small patch and either pull it through
your tree, or please ack' it so Jiri can pull it through the trivial
tree.
Patch against linux-next-tree, 22. Dez 08:38:18 CET 2009
but also present in linus tree.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Acked-by: Tony Lindgren <tony@atomide.com>
This should fix:
WARNING: at drivers/base/core.c:131 device_release+0x68/0x7c()
Device 'omapdss' does not have a release() function, it is broken and
must be fixed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
omapfb platform device was still used to get clocks inside rfbi.c
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Tested-by: Sergey Lapin <slapin@ossfans.org>
Bail out if we don't find an enclosing IOC. Previously, if we didn't
find one, we tried to set things up using garbage for the SBA/IOC register
address, which causes a crash.
This crash only happens if firmware supplies a defective ACPI namespace, so
it doesn't fix any problems in the field.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Commit 15b8dd53f5 changed the string in info->hardware_id from a static
array to a pointer and added a length field. But instead of changing
"sizeof(array)" to "length", we changed it to "sizeof(length)" (== 4),
which corrupts the string we're trying to null-terminate.
We no longer even need to null-terminate the string, but we *do* need to
check whether we found a HID. If there's no HID, we used to have an empty
array, but now we have a null pointer.
The combination of these defects causes this oops:
Unable to handle kernel NULL pointer dereference (address 0000000000000003)
modprobe[895]: Oops 8804682956800 [1]
ip is at zx1_gart_probe+0xd0/0xcc0 [hp_agp]
http://marc.info/?l=linux-ia64&m=126264484923647&w=2
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Reported-by: Émeric Maschino <emeric.maschino@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
While investigating a kmemleak detected leak, I encountered the
agp_add_bridge function. It appears to be responsible for freeing
the agp_bridge_data in the case of a failure, but it is only doing
so for some errors.
Fix it to always free the bridge data if a failure condition is
encountered.
Signed-off-by: Kevin Winchester <kjwinchester@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'for-airlied' of /ssd/git/drm-nouveau-next: (28 commits)
drm/nv04: Fix set_operation software method.
drm/nouveau: initialise DMA tracking parameters earlier
drm/nouveau: use dma.max rather than pushbuf size for checking GET validity
drm/nv04: differentiate between nv04/nv05
drm/nouveau: Fix null deref in nouveau_fence_emit due to deleted fence
drm/nv50: prevent a possible ctxprog hang
drm/nouveau: have ttm's fault handler called directly
drm/nv50: restore correct cache1 get/put address on fifoctx load
drm/nouveau: create function for "dealing" with gpu lockup
drm/nouveau: remove unused nouveau_channel_idle() function
drm/nouveau: fix handling of fbcon colours in 8bpp
drm/nv04: Context switching fixes.
drm/nouveau: Use the software object for fencing.
drm/nouveau: Allocate a per-channel instance of NV_SW.
drm/nv50: make the blocksize depend on vram size
drm/nouveau: better alignment of bo sizes and use roundup instead of ALIGN
drm/nouveau: Don't skip card take down on nv0x.
drm/nouveau: Implement nv42-nv43 TV load detection.
drm/nouveau: Clean up the nv17-nv4x load detection code a bit.
drm/nv50: fix fillrect color
...
* korg/drm-radeon-next:
drm/radeon/kms: add additional safe regs for r4xx/rs6xx and r5xx
drm/radeon/kms: Don't try to enable IRQ if we have no handler installed
drm: Avoid calling vblank function is vblank wasn't initialized
drm/radeon: mkregtable.c: close a file before exit
drm/radeon/kms: Make sure we release AGP device if we acquired it
drm/radeon/kms: Schedule host path read cache flush through the ring V2
drm/radeon/kms: Workaround RV410/R420 CP errata (V3)
drm/radeon/kms: detect sideport memory on IGP chips
drm/radeon: fix a couple of array index errors
drm/radeon/kms: add support for eDP (embedded DisplayPort)
drm: Add eDP connector type
drm/radeon/kms: pull in the latest upstream ObjectID.h changes
drm/radeon/kms: whitespace changes to ObjectID.h
drm/radeon/kms: fix typo in atom connector type handling
Some upcoming G80 DMA changes will depend on this, but it's split out for
bisectibility just in case it causes some unexpected issues.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Currently Nouveau will unvalidate all buffers if it is forced to wait on
one, and then start revalidating from the beginning. While doing so, it
destroys the operation fence, causing nouveau_fence_emit to crash.
This patch fixes this bug by taking the fence object out of validate_op
and creating it just before emit. The fence pointer is initialized to 0
and unref'ed unconditionally.
In addition to fixing the bug, this prevents its reintroduction and
simplifies the code.
Signed-off-by: Luca Barbieri <luca@luca-barbieri.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The below is mainly an educated guess at what's going on, docs would
sure be handy... NVIDIA? :P
It appears it's possible for a ctxprog to run even while a GPU exception
is pending. The GF8 and up ctxprogs appear to have a small snippet of
code which detects this, and stalls the ctxprog until it's been handled,
which essentially looks like:
if (r2 & 0x00008000) {
r0 |= 0x80000000;
while (r0 & 0x80000000) {}
}
I don't know of any way that flag would get cleared unless the driver
intervenes (and indeed, in the cases I've seen the hang, nothing steps
in to automagically clear it for us). This patch causes the driver to
clear the flag during the PGRAPH IRQ handler.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
