Currently, we have four versions of rcu_read_lock_sched_held(), depending
on the combined choices on PREEMPT_COUNT and DEBUG_LOCK_ALLOC. However,
there is an existing function preemptible() that already distinguishes
between the PREEMPT_COUNT=y and PREEMPT_COUNT=n cases, and allows these
four implementations to be consolidated down to two.
This commit therefore uses preemptible() to achieve this consolidation.
Note that there could be a small performance regression in the case
of CONFIG_DEBUG_LOCK_ALLOC=y && PREEMPT_COUNT=n. However, given the
overhead associated with CONFIG_DEBUG_LOCK_ALLOC=y, this should be
down in the noise.
Signed-off-by: Boqun Feng <boqun.feng@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
This commit consolidates a couple definitions and several calls for
single-shot ftrace-buffer dumping.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Pull cpu hotplug updates from Thomas Gleixner:
"This is the first part of the ongoing cpu hotplug rework:
- Initial implementation of the state machine
- Runs all online and prepare down callbacks on the plugged cpu and
not on some random processor
- Replaces busy loop waiting with completions
- Adds tracepoints so the states can be followed"
More detailed commentary on this work from an earlier email:
"What's wrong with the current cpu hotplug infrastructure?
- Asymmetry
The hotplug notifier mechanism is asymmetric versus the bringup and
teardown. This is mostly caused by the notifier mechanism.
- Largely undocumented dependencies
While some notifiers use explicitely defined notifier priorities,
we have quite some notifiers which use numerical priorities to
express dependencies without any documentation why.
- Control processor driven
Most of the bringup/teardown of a cpu is driven by a control
processor. While it is understandable, that preperatory steps,
like idle thread creation, memory allocation for and initialization
of essential facilities needs to be done before a cpu can boot,
there is no reason why everything else must run on a control
processor. Before this patch series, bringup looks like this:
Control CPU Booting CPU
do preparatory steps
kick cpu into life
do low level init
sync with booting cpu sync with control cpu
bring the rest up
- All or nothing approach
There is no way to do partial bringups. That's something which is
really desired because we waste e.g. at boot substantial amount of
time just busy waiting that the cpu comes to life. That's stupid
as we could very well do preparatory steps and the initial IPI for
other cpus and then go back and do the necessary low level
synchronization with the freshly booted cpu.
- Minimal debuggability
Due to the notifier based design, it's impossible to switch between
two stages of the bringup/teardown back and forth in order to test
the correctness. So in many hotplug notifiers the cancel
mechanisms are either not existant or completely untested.
- Notifier [un]registering is tedious
To [un]register notifiers we need to protect against hotplug at
every callsite. There is no mechanism that bringup/teardown
callbacks are issued on the online cpus, so every caller needs to
do it itself. That also includes error rollback.
What's the new design?
The base of the new design is a symmetric state machine, where both
the control processor and the booting/dying cpu execute a well
defined set of states. Each state is symmetric in the end, except
for some well defined exceptions, and the bringup/teardown can be
stopped and reversed at almost all states.
So the bringup of a cpu will look like this in the future:
Control CPU Booting CPU
do preparatory steps
kick cpu into life
do low level init
sync with booting cpu sync with control cpu
bring itself up
The synchronization step does not require the control cpu to wait.
That mechanism can be done asynchronously via a worker or some
other mechanism.
The teardown can be made very similar, so that the dying cpu cleans
up and brings itself down. Cleanups which need to be done after
the cpu is gone, can be scheduled asynchronously as well.
There is a long way to this, as we need to refactor the notion when a
cpu is available. Today we set the cpu online right after it comes
out of the low level bringup, which is not really correct.
The proper mechanism is to set it to available, i.e. cpu local
threads, like softirqd, hotplug thread etc. can be scheduled on that
cpu, and once it finished all booting steps, it's set to online, so
general workloads can be scheduled on it. The reverse happens on
teardown. First thing to do is to forbid scheduling of general
workloads, then teardown all the per cpu resources and finally shut it
off completely.
This patch series implements the basic infrastructure for this at the
core level. This includes the following:
- Basic state machine implementation with well defined states, so
ordering and prioritization can be expressed.
- Interfaces to [un]register state callbacks
This invokes the bringup/teardown callback on all online cpus with
the proper protection in place and [un]installs the callbacks in
the state machine array.
For callbacks which have no particular ordering requirement we have
a dynamic state space, so that drivers don't have to register an
explicit hotplug state.
If a callback fails, the code automatically does a rollback to the
previous state.
- Sysfs interface to drive the state machine to a particular step.
This is only partially functional today. Full functionality and
therefor testability will be achieved once we converted all
existing hotplug notifiers over to the new scheme.
- Run all CPU_ONLINE/DOWN_PREPARE notifiers on the booting/dying
processor:
Control CPU Booting CPU
do preparatory steps
kick cpu into life
do low level init
sync with booting cpu sync with control cpu
wait for boot
bring itself up
Signal completion to control cpu
In a previous step of this work we've done a full tree mechanical
conversion of all hotplug notifiers to the new scheme. The balance
is a net removal of about 4000 lines of code.
This is not included in this series, as we decided to take a
different approach. Instead of mechanically converting everything
over, we will do a proper overhaul of the usage sites one by one so
they nicely fit into the symmetric callback scheme.
I decided to do that after I looked at the ugliness of some of the
converted sites and figured out that their hotplug mechanism is
completely buggered anyway. So there is no point to do a
mechanical conversion first as we need to go through the usage
sites one by one again in order to achieve a full symmetric and
testable behaviour"
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
cpu/hotplug: Document states better
cpu/hotplug: Fix smpboot thread ordering
cpu/hotplug: Remove redundant state check
cpu/hotplug: Plug death reporting race
rcu: Make CPU_DYING_IDLE an explicit call
cpu/hotplug: Make wait for dead cpu completion based
cpu/hotplug: Let upcoming cpu bring itself fully up
arch/hotplug: Call into idle with a proper state
cpu/hotplug: Move online calls to hotplugged cpu
cpu/hotplug: Create hotplug threads
cpu/hotplug: Split out the state walk into functions
cpu/hotplug: Unpark smpboot threads from the state machine
cpu/hotplug: Move scheduler cpu_online notifier to hotplug core
cpu/hotplug: Implement setup/removal interface
cpu/hotplug: Make target state writeable
cpu/hotplug: Add sysfs state interface
cpu/hotplug: Hand in target state to _cpu_up/down
cpu/hotplug: Convert the hotplugged cpu work to a state machine
cpu/hotplug: Convert to a state machine for the control processor
cpu/hotplug: Add tracepoints
...
Make the RCU CPU_DYING_IDLE callback an explicit function call, so it gets
invoked at the proper place.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arch@vger.kernel.org
Cc: Rik van Riel <riel@redhat.com>
Cc: Rafael Wysocki <rafael.j.wysocki@intel.com>
Cc: "Srivatsa S. Bhat" <srivatsa@mit.edu>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Paul McKenney <paulmck@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul Turner <pjt@google.com>
Link: http://lkml.kernel.org/r/20160226182341.870167933@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Because there are neither uses nor intended uses for the
rcu_user_hooks_switch() function that was orginally intended
for nohz use, this commit removes it.
Signed-off-by: Yang Shi <yang.shi@linaro.org>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
rcu_dereference_raw() calls indirectly rcu_read_lock_held() while
rcu_dereference_raw_notrace() does not so fix the comment about the latter.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
This commit replaces a local_irq_save()/local_irq_restore() pair with
a lockdep assertion that interrupts are already disabled. This should
remove the corresponding overhead from the interrupt entry/exit fastpaths.
This change was inspired by the fact that Iftekhar Ahmed's mutation
testing showed that removing rcu_irq_enter()'s call to local_ird_restore()
had no effect, which might indicate that interrupts were always enabled
anyway.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
The rcu_expedited, rcu_normal, and rcu_normal_after_boot kernel boot
parameters are pointless in the case of TINY_RCU because in that case
synchronous grace periods, both expedited and normal, are no-ops.
However, these three symbols contribute several hundred bytes of bloat.
This commit therefore uses CPP directives to avoid compiling this code
in TINY_RCU kernels.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Although expedited grace periods can be quite useful, and although their
OS jitter has been greatly reduced, they can still pose problems for
extreme real-time workloads. This commit therefore adds a rcu_normal
kernel boot parameter (which can also be manipulated via sysfs)
to suppress expedited grace periods, that is, to treat requests for
expedited grace periods as if they were requests for normal grace periods.
If both rcu_expedited and rcu_normal are specified, rcu_normal wins.
This means that if you are relying on expedited grace periods to speed up
boot, you will want to specify rcu_expedited on the kernel command line,
and then specify rcu_normal via sysfs once boot completes.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
The old rcu_lockdep_assert() was retained to ease handling of incoming
patches, but any use will result in deprecated warnings. However, its
replacement, RCU_LOCKDEP_WARN(), is now upstream. It is therefore
time to remove rcu_lockdep_assert(), which this commit does.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
This commit adds an rcu_pointer_handoff() that is intended to mark
situations where a structure's protection transitions from RCU to some
other mechanism (locking, reference counting, whatever). These markings
should allow external tools to more easily spot bugs involving leaking
pointers out of RCU read-side critical sections.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Because preempt_disable() maps to barrier() for non-debug builds,
it forces the compiler to spill and reload registers. Because Tree
RCU and Tiny RCU now only appear in CONFIG_PREEMPT=n builds, these
barrier() instances generate needless extra code for each instance of
rcu_read_lock() and rcu_read_unlock(). This extra code slows down Tree
RCU and bloats Tiny RCU.
This commit therefore removes the preempt_disable() and preempt_enable()
from the non-preemptible implementations of __rcu_read_lock() and
__rcu_read_unlock(), respectively. However, for debug purposes,
preempt_disable() and preempt_enable() are still invoked if
CONFIG_PREEMPT_COUNT=y, because this allows detection of sleeping inside
atomic sections in non-preemptible kernels.
However, Tiny and Tree RCU operates by coalescing all RCU read-side
critical sections on a given CPU that lie between successive quiescent
states. It is therefore necessary to compensate for removing barriers
from __rcu_read_lock() and __rcu_read_unlock() by adding them to a
couple of the RCU functions invoked during quiescent states, namely to
rcu_all_qs() and rcu_note_context_switch(). However, note that the latter
is more paranoia than necessity, at least until link-time optimizations
become more aggressive.
This is based on an earlier patch by Paul E. McKenney, fixing
a bug encountered in kernels built with CONFIG_PREEMPT=n and
CONFIG_PREEMPT_COUNT=y.
Signed-off-by: Boqun Feng <boqun.feng@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
As we now have rcu_callback_t typedefs as the type of rcu callbacks, we
should use it in call_rcu*() and friends as the type of parameters. This
could save us a few lines of code and make it clear which function
requires an rcu callbacks rather than other callbacks as its argument.
Besides, this can also help cscope to generate a better database for
code reading.
Signed-off-by: Boqun Feng <boqun.feng@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Code like this in inline functions confuses some recent versions of gcc:
const int n = const-expr;
whatever_t array[n];
For more details, see:
https://gcc.gnu.org/bugzilla/show_bug.cgi?id=67055#c13
This compiler bug results in the following failure after 114b7fd4b (rcu:
Create rcu_sync infrastructure):
In file included from include/linux/rcupdate.h:429:0,
from include/linux/rcu_sync.h:5,
from kernel/rcu/sync.c:1:
include/linux/rcutiny.h: In function 'rcu_barrier_sched':
include/linux/rcutiny.h:55:20: internal compiler error: Segmentation fault
static inline void rcu_barrier_sched(void)
This commit therefore eliminates the constant local variable in favor of
direct use of the expression.
Reported-and-tested-by: Mark Salter <msalter@redhat.com>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
This commit renames rcu_lockdep_assert() to RCU_LOCKDEP_WARN() for
consistency with the WARN() series of macros. This also requires
inverting the sense of the conditional, which this commit also does.
Reported-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
There have been several requests for a primitive that waits for
grace periods for several RCU flavors concurrently, so this
commit creates it. This is a variadic macro, and you pass in
the call_rcu() functions of the flavors of RCU that you wish to
wait for.
Note that you cannot pass in call_srcu() for two reasons: (1) This
would result in a type mismatch and (2) You need to specify which
srcu_struct you want to use. Handle this by creating a wrapper
function for your SRCU domain, for example:
void call_srcu_mine(struct rcu_head *head, rcu_callback_t func)
{
call_srcu(&ss_mine, head, func);
}
You can then do something like this:
synchronize_rcu_mult(call_srcu_mine, call_rcu, call_rcu_sched);
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
For the paranoid amongst us GCC would be in its right to use byte stores
to write our NULL value, tell it not to do that.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
DEBUG_LOCK_ALLOC=y is not a production setting, but it is
not very unusual either. Many developers routinely
use kernels built with it enabled.
Apart from being selected by hand, it is also auto-selected by
PROVE_LOCKING "Lock debugging: prove locking correctness" and
LOCK_STAT "Lock usage statistics" config options.
LOCK STAT is necessary for "perf lock" to work.
I wouldn't spend too much time optimizing it, but this particular
function has a very large cost in code size: when it is deinlined,
code size decreases by 830,000 bytes:
text data bss dec hex filename
85674192 22294776 20627456 128596424 7aa39c8 vmlinux.before
84837612 22294424 20627456 127759492 79d7484 vmlinux
(with this config: http://busybox.net/~vda/kernel_config)
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
CC: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
CC: Josh Triplett <josh@joshtriplett.org>
CC: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
CC: Lai Jiangshan <laijs@cn.fujitsu.com>
CC: Tejun Heo <tj@kernel.org>
CC: Oleg Nesterov <oleg@redhat.com>
CC: linux-kernel@vger.kernel.org
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
The RCU_USER_QS Kconfig parameter is now just a synonym for NO_HZ_FULL,
so this commit eliminates RCU_USER_QS, replacing all uses with NO_HZ_FULL.
Reported-by: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Main excitement here is Peter Zijlstra's lockless rbtree optimization to
speed module address lookup. He found some abusers of the module lock
doing that too.
A little bit of parameter work here too; including Dan Streetman's breaking
up the big param mutex so writing a parameter can load another module (yeah,
really). Unfortunately that broke the usual suspects, !CONFIG_MODULES and
!CONFIG_SYSFS, so those fixes were appended too.
Cheers,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tWPQ
-----END PGP SIGNATURE-----
Merge tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module updates from Rusty Russell:
"Main excitement here is Peter Zijlstra's lockless rbtree optimization
to speed module address lookup. He found some abusers of the module
lock doing that too.
A little bit of parameter work here too; including Dan Streetman's
breaking up the big param mutex so writing a parameter can load
another module (yeah, really). Unfortunately that broke the usual
suspects, !CONFIG_MODULES and !CONFIG_SYSFS, so those fixes were
appended too"
* tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (26 commits)
modules: only use mod->param_lock if CONFIG_MODULES
param: fix module param locks when !CONFIG_SYSFS.
rcu: merge fix for Convert ACCESS_ONCE() to READ_ONCE() and WRITE_ONCE()
module: add per-module param_lock
module: make perm const
params: suppress unused variable error, warn once just in case code changes.
modules: clarify CONFIG_MODULE_COMPRESS help, suggest 'N'.
kernel/module.c: avoid ifdefs for sig_enforce declaration
kernel/workqueue.c: remove ifdefs over wq_power_efficient
kernel/params.c: export param_ops_bool_enable_only
kernel/params.c: generalize bool_enable_only
kernel/module.c: use generic module param operaters for sig_enforce
kernel/params: constify struct kernel_param_ops uses
sysfs: tightened sysfs permission checks
module: Rework module_addr_{min,max}
module: Use __module_address() for module_address_lookup()
module: Make the mod_tree stuff conditional on PERF_EVENTS || TRACING
module: Optimize __module_address() using a latched RB-tree
rbtree: Implement generic latch_tree
seqlock: Introduce raw_read_seqcount_latch()
...
Pull timer updates from Thomas Gleixner:
"A rather largish update for everything time and timer related:
- Cache footprint optimizations for both hrtimers and timer wheel
- Lower the NOHZ impact on systems which have NOHZ or timer migration
disabled at runtime.
- Optimize run time overhead of hrtimer interrupt by making the clock
offset updates smarter
- hrtimer cleanups and removal of restrictions to tackle some
problems in sched/perf
- Some more leap second tweaks
- Another round of changes addressing the 2038 problem
- First step to change the internals of clock event devices by
introducing the necessary infrastructure
- Allow constant folding for usecs/msecs_to_jiffies()
- The usual pile of clockevent/clocksource driver updates
The hrtimer changes contain updates to sched, perf and x86 as they
depend on them plus changes all over the tree to cleanup API changes
and redundant code, which got copied all over the place. The y2038
changes touch s390 to remove the last non 2038 safe code related to
boot/persistant clock"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (114 commits)
clocksource: Increase dependencies of timer-stm32 to limit build wreckage
timer: Minimize nohz off overhead
timer: Reduce timer migration overhead if disabled
timer: Stats: Simplify the flags handling
timer: Replace timer base by a cpu index
timer: Use hlist for the timer wheel hash buckets
timer: Remove FIFO "guarantee"
timers: Sanitize catchup_timer_jiffies() usage
hrtimer: Allow hrtimer::function() to free the timer
seqcount: Introduce raw_write_seqcount_barrier()
seqcount: Rename write_seqcount_barrier()
hrtimer: Fix hrtimer_is_queued() hole
hrtimer: Remove HRTIMER_STATE_MIGRATE
selftest: Timers: Avoid signal deadlock in leap-a-day
timekeeping: Copy the shadow-timekeeper over the real timekeeper last
clockevents: Check state instead of mode in suspend/resume path
selftests: timers: Add leap-second timer edge testing to leap-a-day.c
ntp: Do leapsecond adjustment in adjtimex read path
time: Prevent early expiry of hrtimers[CLOCK_REALTIME] at the leap second edge
ntp: Introduce and use SECS_PER_DAY macro instead of 86400
...
I want to use lockless_dereference() from seqlock.h, which would mean
including rcupdate.h from it, however rcupdate.h already includes
seqlock.h.
Avoid this by moving lockless_dereference() into compiler.h. This is
somewhat tricky since it uses smp_read_barrier_depends() which isn't
available there, but its a CPP macro so we can get away with it.
The alternative would be moving it into asm/barrier.h, but that would
be updating each arch (I can do if people feel that is more
appropriate).
Cc: Paul McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The Tiny RCU counterparts to rcu_idle_enter(), rcu_idle_exit(),
rcu_irq_enter(), and rcu_irq_exit() are empty functions, but each has
EXPORT_SYMBOL_GPL(), which needlessly consumes extra memory, especially
in kernels built with module support. This commit therefore moves these
functions to static inlines in rcutiny.h, removing the need for exports.
This won't affect the size of the tiniest kernels, which are likely
built without module support, but might help semi-tiny kernels that
might include module support.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
This commit converts several CONFIG_RCU_NOCB_CPU_ALL #ifdefs to
instead use IS_ENABLED(). This change should help avoid hiding
code from compiler diagnostics.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Now that rcu_access_index() and rcu_dereference_index_check() are no
longer used, the commit removes them from the RCU API. This means that
RCU's data dependencies now involve only pointers, give or take the
occasional cast to and then back from an integer type to do pointer
arithmetic. This in turn eliminates the need for a number of operations
on values carrying RCU data dependencies.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: linux-edac@vger.kernel.org
Cc: Tony Luck <tony.luck@intel.com>
Acked-by: Borislav Petkov <bp@suse.de>
This commit moves from the old ACCESS_ONCE() API to the new READ_ONCE()
and WRITE_ONCE() APIs.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
[ paulmck: Updated to include kernel/torture.c as suggested by Jason Low. ]
The evaluation of the next timer in the nohz code is based on jiffies
while all the tick internals are nano seconds based. We have also to
convert hrtimer nanoseconds to jiffies in the !highres case. That's
just wrong and introduces interesting corner cases.
Turn it around and convert the next timer wheel timer expiry and the
rcu event to clock monotonic and base all calculations on
nanoseconds. That identifies the case where no timer is pending
clearly with an absolute expiry value of KTIME_MAX.
Makes the code more readable and gets rid of the jiffies magic in the
nohz code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Link: http://lkml.kernel.org/r/20150414203502.184198593@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This commit informs RCU of an outgoing CPU just before that CPU invokes
arch_cpu_idle_dead() during its last pass through the idle loop (via a
new CPU_DYING_IDLE notifier value). This change means that RCU need not
deal with outgoing CPUs passing through the scheduler after informing
RCU that they are no longer online. Note that removing the CPU from
the rcu_node ->qsmaskinit bit masks is done at CPU_DYING_IDLE time,
and orphaning callbacks is still done at CPU_DEAD time, the reason being
that at CPU_DEAD time we have another CPU that can adopt them.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
The rcu_dereference_check() family of primitives evaluates the RCU
lockdep expression first, and only then evaluates the expression passed
in. This works fine normally, but can potentially fail in environments
(such as NMI handlers) where lockdep cannot be invoked. The problem is
that even if the expression passed in is "1", the compiler would need to
prove that the RCU lockdep expression (rcu_read_lock_held(), for example)
is free of side effects in order to be able to elide it. Given that
rcu_read_lock_held() is sometimes separately compiled, the compiler cannot
always use this optimization.
This commit therefore reverse the order of evaluation, so that the
expression passed in is evaluated first, and the RCU lockdep expression is
evaluated only if the passed-in expression evaluated to false, courtesy
of the C-language short-circuit boolean evaluation rules. This compells
the compiler to forego executing the RCU lockdep expression in cases
where the passed-in expression evaluates to "1" at compile time, so that
(for example) rcu_dereference_raw() can be guaranteed to execute safely
within an NMI handler.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
If an RCU read-side critical section occurs within an interrupt handler
or a softirq handler, it cannot have been preempted. Therefore, there is
a check in rcu_read_unlock_special() checking for this error. However,
when this check triggers, it lacks diagnostic information. This commit
therefore moves rcu_read_unlock()'s lockdep annotation to follow the
call to __rcu_read_unlock() and changes rcu_read_unlock_special()'s
WARN_ON_ONCE() to an lockdep_rcu_suspicious() in order to locate where
the offending RCU read-side critical section began. In addition, the
value of the ->rcu_read_unlock_special field is printed.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
This commit adds a CONFIG_RCU_EXPEDITE_BOOT Kconfig parameter
that emulates a very early boot rcu_expedite_gp(). A late-boot
call to rcu_end_inkernel_boot() will provide the corresponding
rcu_unexpedite_gp(). The late-boot call to rcu_end_inkernel_boot()
should be made just before init is spawned.
According to Arjan:
> To show the boot time, I'm using the timestamp of the "Write protecting"
> line, that's pretty much the last thing we print prior to ring 3 execution.
>
> A kernel with default RCU behavior (inside KVM, only virtual devices)
> looks like this:
>
> [ 0.038724] Write protecting the kernel read-only data: 10240k
>
> a kernel with expedited RCU (using the command line option, so that I
> don't have to recompile between measurements and thus am completely
> oranges-to-oranges)
>
> [ 0.031768] Write protecting the kernel read-only data: 10240k
>
> which, in percentage, is an 18% improvement.
Reported-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Tested-by: Arjan van de Ven <arjan@linux.intel.com>
Currently, expediting of normal synchronous grace-period primitives
(synchronize_rcu() and friends) is controlled by the rcu_expedited()
boot/sysfs parameter. This works well, but does not handle nesting.
This commit therefore provides rcu_expedite_gp() to enable expediting
and rcu_unexpedite_gp() to cancel a prior rcu_expedite_gp(), both of
which support nesting.
Reported-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
There are currently duplicate identical definitions of the
rcu_synchronize() structure and the wakeme_after_rcu() function.
Thie commit therefore consolidates them.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Although cond_resched_rcu_qs() only applies to TASKS_RCU, it is used
in places where it would be useful for it to apply to the normal RCU
flavors, rcu_preempt, rcu_sched, and rcu_bh. This is especially the
case for workloads that aggressively overload the system, particularly
those that generate large numbers of RCU updates on systems running
NO_HZ_FULL CPUs. This commit therefore communicates quiescent states
from cond_resched_rcu_qs() to the normal RCU flavors.
Note that it is unfortunately necessary to leave the old ->passed_quiesce
mechanism in place to allow quiescent states that apply to only one
flavor to be recorded. (Yes, we could decrement ->rcu_qs_ctr_snap in
that case, but that is not so good for debugging of RCU internals.)
In addition, if one of the RCU flavor's grace period has stalled, this
will invoke rcu_momentary_dyntick_idle(), resulting in a heavy-weight
quiescent state visible from other CPUs.
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
[ paulmck: Merge commit from Sasha Levin fixing a bug where __this_cpu()
was used in preemptible code. ]
Recently lockless_dereference() was added which can be used in place of
hard-coding smp_read_barrier_depends(). The following PATCH makes the change.
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
The comment above rcu_read_unlock() explains the potential deadlock
if the caller holds one of the locks taken by rt_mutex_unlock() paths,
but it is not clear from this documentation that any lock which can
be taken from interrupt can lead to deadlock as well and we need to
take rt_mutex_lock() into account too.
The problem is that rt_mutex_lock() takes wait_lock without disabling
irqs, and thus an interrupt taking some LOCK can obviously race with
rcu_read_unlock_special() called with the same LOCK held.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
The current implementation of cond_resched_rcu_qs() can invoke
rcu_note_voluntary_context_switch() twice in the should_resched()
case, once via the call to __schedule() and once directly. However, as
noted by Joe Lawrence in a patch to the team subsystem, cond_resched()
returns an indication as to whether or not the call to __schedule()
actually happened. This commit therefore changes cond_resched_rcu_qs()
so as to invoke rcu_note_voluntary_context_switch() only when __schedule()
was not called.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Add a sparse check when RCU_INIT_POINTER() is used to assign a non __rcu
annotated pointer.
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
The "cpu" argument to rcu_needs_cpu() is always the current CPU, so drop
it. This in turn allows the "cpu" argument to rcu_cpu_has_callbacks()
to be removed, which allows the uses of "cpu" in both functions to be
replaced with a this_cpu_ptr(). Again, the anticipated cross-CPU uses
of these functions has been replaced by NO_HZ_FULL.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Pranith Kumar <bobby.prani@gmail.com>
The "cpu" argument was kept around on the off-chance that RCU might
offload scheduler-clock interrupts. However, this offload approach
has been replaced by NO_HZ_FULL, which offloads -all- RCU processing
from qualifying CPUs. It is therefore time to remove the "cpu" argument
to rcu_check_callbacks(), which this commit does.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Pranith Kumar <bobby.prani@gmail.com>
PREEMPT_RCU and TREE_PREEMPT_RCU serve the same function after
TINY_PREEMPT_RCU has been removed. This patch removes TREE_PREEMPT_RCU
and uses PREEMPT_RCU config option in its place.
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Although rcu_dereference() and friends can be used in situations where
object lifetimes are being managed by something other than RCU, the
resulting sparse and lockdep-RCU noise can be annoying. This commit
therefore supplies a lockless_dereference(), which provides the
protection for dereferences without the RCU-related debugging noise.
Reported-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
This commit changes rcutorture_runnable to torture_runnable, which is
consistent with the names of the other parameters and is a bit shorter
as well.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Boqun Feng