As of Xen 4.7 PV CPUID doesn't expose either of CPUID[1].ECX[7] and
CPUID[0x80000007].EDX[7] anymore, causing the driver to fail to load on
both Intel and AMD systems. Doing any kind of hardware capability
checks in the driver as a prerequisite was wrong anyway: With the
hypervisor being in charge, all such checking should be done by it. If
ACPI data gets uploaded despite some missing capability, the hypervisor
is free to ignore part or all of that data.
Ditch the entire check_prereq() function, and do the only valid check
(xen_initial_domain()) in the caller in its place.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
No need to retain a local copy of the full request message, only the
type is really needed.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
xenbus_dev_request_and_reply() needs to track whether a transaction is
open. For XS_TRANSACTION_START messages it calls transaction_start()
and for XS_TRANSACTION_END messages it calls transaction_end().
If sending an XS_TRANSACTION_START message fails or responds with an
an error, the transaction is not open and transaction_end() must be
called.
If sending an XS_TRANSACTION_END message fails, the transaction is
still open, but if an error response is returned the transaction is
closed.
Commit 027bd7e899 ("xen/xenbus: Avoid synchronous wait on XenBus
stalling shutdown/restart") introduced a regression where failed
XS_TRANSACTION_START messages were leaving the transaction open. This
can cause problems with suspend (and migration) as all transactions
must be closed before suspending.
It appears that the problematic change was added accidentally, so just
remove it.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Inability to locate a user mode specified transaction ID should not
lead to a kernel crash. For other than XS_TRANSACTION_START also
don't issue anything to xenbus if the specified ID doesn't match that
of any active transaction.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Reads following writes with all address bits set to 1 should return all
changeable address bits as one, not the BAR size (nor, as was the case
for the upper half of 64-bit BARs, the high half of the region's end
address). Presumably this didn't cause any problems so far because
consumers use the value to calculate the size (usually via val & -val),
and do nothing else with it.
But also consider the exception here: Unimplemented BARs should always
return all zeroes.
And finally, the check for whether to return the sizing address on read
for the ROM BAR should ignore all non-address bits, not just the ROM
Enable one.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Current overlap check is evaluating to false a case where a filter
field is fully contained (proper subset) of a r/w request. This
change applies classical overlap check instead to include all the
scenarios.
More specifically, for (Hilscher GmbH CIFX 50E-DP(M/S)) device driver
the logic is such that the entire confspace is read and written in 4
byte chunks. In this case as an example, CACHE_LINE_SIZE,
LATENCY_TIMER and PCI_BIST are arriving together in one call to
xen_pcibk_config_write() with offset == 0xc and size == 4. With the
exsisting overlap check the LATENCY_TIMER field (offset == 0xd, length
== 1) is fully contained in the write request and hence is excluded
from write, which is incorrect.
Signed-off-by: Andrey Grodzovsky <andrey2805@gmail.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: Jan Beulich <JBeulich@suse.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Fix a declared-but-not-defined warning when building with
XEN_BALLOON_MEMORY_HOTPLUG=n. This fixes a regression introduced by
commit dfd74a1edf ("xen/balloon: Fix crash when ballooning on x86 32
bit PAE").
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Acked-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Pull SCSI target updates from Nicholas Bellinger:
"Here are the outstanding target pending updates for v4.7-rc1.
The highlights this round include:
- Allow external PR/ALUA metadata path be defined at runtime via top
level configfs attribute (Lee)
- Fix target session shutdown bug for ib_srpt multi-channel (hch)
- Make TFO close_session() and shutdown_session() optional (hch)
- Drop se_sess->sess_kref + convert tcm_qla2xxx to internal kref
(hch)
- Add tcm_qla2xxx endpoint attribute for basic FC jammer (Laurence)
- Refactor iscsi-target RX/TX PDU encode/decode into common code
(Varun)
- Extend iscsit_transport with xmit_pdu, release_cmd, get_rx_pdu,
validate_parameters, and get_r2t_ttt for generic ISO offload
(Varun)
- Initial merge of cxgb iscsi-segment offload target driver (Varun)
The bulk of the changes are Chelsio's new driver, along with a number
of iscsi-target common code improvements made by Varun + Co along the
way"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (29 commits)
iscsi-target: Fix early sk_data_ready LOGIN_FLAGS_READY race
cxgbit: Use type ISCSI_CXGBIT + cxgbit tpg_np attribute
iscsi-target: Convert transport drivers to signal rdma_shutdown
iscsi-target: Make iscsi_tpg_np driver show/store use generic code
tcm_qla2xxx Add SCSI command jammer/discard capability
iscsi-target: graceful disconnect on invalid mapping to iovec
target: need_to_release is always false, remove redundant check and kfree
target: remove sess_kref and ->shutdown_session
iscsi-target: remove usage of ->shutdown_session
tcm_qla2xxx: introduce a private sess_kref
target: make close_session optional
target: make ->shutdown_session optional
target: remove acl_stop
target: consolidate and fix session shutdown
cxgbit: add files for cxgbit.ko
iscsi-target: export symbols
iscsi-target: call complete on conn_logout_comp
iscsi-target: clear tx_thread_active
iscsi-target: add new offload transport type
iscsi-target: use conn_transport->transport_type in text rsp
...
The XEN UEFI code has become available on the ARM architecture
recently, but now causes a link-time warning:
ld: warning: drivers/xen/efi.o uses 2-byte wchar_t yet the output is to use 4-byte wchar_t; use of wchar_t values across objects may fail
This seems harmless, because the efi code only uses 2-byte
characters when interacting with EFI, so we don't pass on those
strings to elsewhere in the system, and we just need to
silence the warning.
It is not clear to me whether we actually need to build the file
with the -fshort-wchar flag, but if we do, then we should also
pass --no-wchar-size-warning to the linker, to avoid the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Fixes: 37060935dc04 ("ARM64: XEN: Add a function to initialize Xen specific UEFI runtime services")
IOCTL_GNTDEV_GRANT_COPY batches copy operations to reduce the number
of hypercalls. The stack is used to avoid a memory allocation in a
hot path. However, a batch size of 24 requires more than 1024 bytes of
stack which in some configurations causes a compiler warning.
xen/gntdev.c: In function ‘gntdev_ioctl_grant_copy’:
xen/gntdev.c:949:1: warning: the frame size of 1248 bytes is
larger than 1024 bytes [-Wframe-larger-than=]
This is a harmless warning as there is still plenty of stack spare,
but people keep trying to "fix" it. Reduce the batch size to 16 to
reduce stack usage to less than 1024 bytes. This should have minimal
impact on performance.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Turns out the template and thus many drivers got the return value wrong:
0 means the fabrics driver needs to put a session reference, which no
driver except for the iSCSI target drivers did. Fortunately none of these
drivers supports explicit Node ACLs, so the bug was harmless.
Even without that only qla2xxx and iscsi every did real work in
shutdown_session, so get rid of the boilerplate code in all other
drivers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The copying of ring data was wrong for two cases: For a full ring
nothing got copied at all (as in that case the canonicalized producer
and consumer indexes are identical). And in case one or both of the
canonicalized (after the resize) indexes would point into the second
half of the buffer, the copied data ended up in the wrong (free) part
of the new buffer. In both cases uninitialized data would get passed
back to the caller.
Fix this by simply copying the old ring contents twice: Once to the
low half of the new buffer, and a second time to the high half.
This addresses the inability to boot a HVM guest with 64 or more
vCPUs. This regression was caused by 8620015499 (xen/evtchn:
dynamically grow pending event channel ring).
Reported-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: <stable@vger.kernel.org> # 4.4+
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
So the following commit:
884f4f66ff ("efi: Remove global 'memmap' EFI memory map")
... triggered the following build warning on x86 64-bit allyesconfig:
drivers/xen/efi.c:290:47: warning: missing braces around initializer [-Wmissing-braces]
It's this initialization in drivers/xen/efi.c:
static const struct efi efi_xen __initconst = {
...
.memmap = NULL, /* Not used under Xen. */
...
which was forgotten about, as .memmap now is an embedded struct:
struct efi_memory_map memmap;
We can remove this initialization - it's an EFI core internal data structure plus
it's not used in the Xen driver anyway.
Reviewed-by: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: ard.biesheuvel@linaro.org
Cc: bp@alien8.de
Cc: linux-tip-commits@vger.kernel.org
Cc: tony.luck@intel.com
Link: http://lkml.kernel.org/r/20160429083128.GA4925@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Commit 55b3da98a4 (xen/balloon: find
non-conflicting regions to place hotplugged memory) caused a
regression in 4.4.
When ballooning on an x86 32 bit PAE system with close to 64 GiB of
memory, the address returned by allocate_resource may be above 64 GiB.
When using CONFIG_SPARSEMEM, this setup is limited to using physical
addresses < 64 GiB. When adding memory at this address, it runs off
the end of the mem_section array and causes a crash. Instead, fail
the ballooning request.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Cc: <stable@vger.kernel.org> # 4.4+
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Moving an unmasked irq may result in irq handler being invoked on both
source and target CPUs.
With 2-level this can happen as follows:
On source CPU:
evtchn_2l_handle_events() ->
generic_handle_irq() ->
handle_edge_irq() ->
eoi_pirq():
irq_move_irq(data);
/***** WE ARE HERE *****/
if (VALID_EVTCHN(evtchn))
clear_evtchn(evtchn);
If at this moment target processor is handling an unrelated event in
evtchn_2l_handle_events()'s loop it may pick up our event since target's
cpu_evtchn_mask claims that this event belongs to it *and* the event is
unmasked and still pending. At the same time, source CPU will continue
executing its own handle_edge_irq().
With FIFO interrupt the scenario is similar: irq_move_irq() may result
in a EVTCHNOP_unmask hypercall which, in turn, may make the event
pending on the target CPU.
We can avoid this situation by moving and clearing the event while
keeping event masked.
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
- Make earlyprintk=xen work for HVM guests.
- Remove module support for things never built as modules.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJW8YhlAAoJEFxbo/MsZsTRiCgH/3GnL93s/BsRTrA/DYykYqA4
rPPkDd6WMlEbrko6FY7o4IxUAZ50LWU8wjmDNVTT+R/VKlWCVh2+ksxjbH8e0nzr
0QohAYTdG1VGmhkrwTjKj0wC3Nr8vaDqoBXAFRz4DiQdbobn12wzXjaVrbl8RRNc
oHDqR+DfZj6ontqx8oFkkTk7CFKIGEOtm/uBhCAV2fNkQSUCzuQyKLlarxM6jq/2
EnLR1bhnyoy5zNFzXxmaJgZOit8QFMKvPdDRknlp9yDHYJ5zolJkv+6FPiAG6SZs
A8yAUPQoAD+ekAiV2DIhb8qoNNNdZXdRCFBpoudwX3GyyU4O2P5Intl0xEg17Nk=
=L8S4
-----END PGP SIGNATURE-----
Merge tag 'for-linus-4.6-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen updates from David Vrabel:
"Features and fixes for 4.6:
- Make earlyprintk=xen work for HVM guests
- Remove module support for things never built as modules"
* tag 'for-linus-4.6-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
drivers/xen: make platform-pci.c explicitly non-modular
drivers/xen: make sys-hypervisor.c explicitly non-modular
drivers/xen: make xenbus_dev_[front/back]end explicitly non-modular
drivers/xen: make [xen-]ballon explicitly non-modular
xen: audit usages of module.h ; remove unnecessary instances
xen/x86: Drop mode-selecting ifdefs in startup_xen()
xen/x86: Zero out .bss for PV guests
hvc_xen: make early_printk work with HVM guests
hvc_xen: fix xenboot for DomUs
hvc_xen: add earlycon support
Pull SCSI target updates from Nicholas Bellinger:
"The highlights this round include:
- Add target_alloc_session() w/ callback helper for doing se_session
allocation + tag + se_node_acl lookup. (HCH + nab)
- Tree-wide fabric driver conversion to use target_alloc_session()
- Convert sbp-target to use percpu_ida tag pre-allocation, and
TARGET_SCF_ACK_KREF I/O krefs (Chris Boot + nab)
- Convert usb-gadget to use percpu_ida tag pre-allocation, and
TARGET_SCF_ACK_KREF I/O krefs (Andrzej Pietrasiewicz + nab)
- Convert xen-scsiback to use percpu_ida tag pre-allocation, and
TARGET_SCF_ACK_KREF I/O krefs (Juergen Gross + nab)
- Convert tcm_fc to use TARGET_SCF_ACK_KREF I/O + TMR krefs
- Convert ib_srpt to use percpu_ida tag pre-allocation
- Add DebugFS node for qla2xxx target sess list (Quinn)
- Rework iser-target connection termination (Jenny + Sagi)
- Convert iser-target to new CQ API (HCH)
- Add pass-through WRITE_SAME support for IBLOCK (Mike Christie)
- Introduce data_bitmap for asynchronous access of data area (Sheng
Yang + Andy)
- Fix target_release_cmd_kref shutdown comp leak (Himanshu Madhani)
Also, there is a separate PULL request coming for cxgb4 NIC driver
prerequisites for supporting hw iscsi segmentation offload (ISO), that
will be the base for a number of v4.7 developments involving
iscsi-target hw offloads"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (36 commits)
target: Fix target_release_cmd_kref shutdown comp leak
target: Avoid DataIN transfers for non-GOOD SAM status
target/user: Report capability of handling out-of-order completions to userspace
target/user: Fix size_t format-spec build warning
target/user: Don't free expired command when time out
target/user: Introduce data_bitmap, replace data_length/data_head/data_tail
target/user: Free data ring in unified function
target/user: Use iovec[] to describe continuous area
target: Remove enum transport_lunflags_table
target/iblock: pass WRITE_SAME to device if possible
iser-target: Kill the ->isert_cmd back pointer in struct iser_tx_desc
iser-target: Kill struct isert_rdma_wr
iser-target: Convert to new CQ API
iser-target: Split and properly type the login buffer
iser-target: Remove ISER_RECV_DATA_SEG_LEN
iser-target: Remove impossible condition from isert_wait_conn
iser-target: Remove redundant wait in release_conn
iser-target: Rework connection termination
iser-target: Separate flows for np listeners and connections cma events
iser-target: Add new state ISER_CONN_BOUND to isert_conn
...
The Kconfig currently controlling compilation of this code is:
arch/x86/xen/Kconfig:config XEN_PVHVM
arch/x86/xen/Kconfig: def_bool y
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
In removing "module" from the init fcn name, we observe a namespace
collision with the probe function, so we use "probe" in the name of
the probe function, and "init" in the registration fcn, as per
standard convention, as suggested by Stefano.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Reviewed-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
The Kconfig currently controlling compilation of this code is:
config XEN_SYS_HYPERVISOR
bool "Create xen entries under /sys/hypervisor"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit. However
one could argue that fs_initcall() might make more sense here.
This change means that the one line function xen_properties_destroy()
has only one user left, and since that is inside an #ifdef, we just
manually inline it there vs. adding more ifdeffery around the function
to avoid compile warnings about "defined but not used".
In order to be consistent we also manually inline the other _destroy
functions that are also just one line sysfs functions calls with only
one call site remaing, even though they wouldn't need #ifdeffery.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Reviewed-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
The Makefile / Kconfig currently controlling compilation here is:
obj-y += xenbus_dev_frontend.o
[...]
obj-$(CONFIG_XEN_BACKEND) += xenbus_dev_backend.o
...with:
drivers/xen/Kconfig:config XEN_BACKEND
drivers/xen/Kconfig: bool "Backend driver support"
...meaning that they currently are not being built as modules by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
We also delete the MODULE_LICENSE tag since all that information
is already contained at the top of the file in the comments.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Reviewed-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
The Makefile / Kconfig currently controlling compilation here is:
obj-y += grant-table.o features.o balloon.o manage.o preempt.o time.o
[...]
obj-$(CONFIG_XEN_BALLOON) += xen-balloon.o
...with:
drivers/xen/Kconfig:config XEN_BALLOON
drivers/xen/Kconfig: bool "Xen memory balloon driver"
...meaning that they currently are not being built as modules by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
In doing so we uncover two implict includes that were obtained
by module.h having such a wide include scope itself:
In file included from drivers/xen/xen-balloon.c:41:0:
include/xen/balloon.h:26:51: warning: ‘struct page’ declared inside parameter list [enabled by default]
int alloc_xenballooned_pages(int nr_pages, struct page **pages);
^
include/xen/balloon.h: In function ‘register_xen_selfballooning’:
include/xen/balloon.h:35:10: error: ‘ENOSYS’ undeclared (first use in this function)
return -ENOSYS;
^
This is fixed by adding mm-types.h and errno.h to the list.
We also delete the MODULE_LICENSE tags since all that information
is already contained at the top of the file in the comments.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Reviewed-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Code that uses no modular facilities whatsoever should not be
sourcing module.h at all, since that header drags in a bunch
of other headers with it.
Similarly, code that is not explicitly using modular facilities
like module_init() but only is declaring module_param setup
variables should be using moduleparam.h and not the larger
module.h file for that.
In making this change, we also uncover an implicit use of BUG()
in inline fcns within arch/arm/include/asm/xen/hypercall.h so
we explicitly source <linux/bug.h> for that file now.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Reviewed-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Currently, all newly added memory blocks remain in 'offline' state
unless someone onlines them, some linux distributions carry special udev
rules like:
SUBSYSTEM=="memory", ACTION=="add", ATTR{state}=="offline", ATTR{state}="online"
to make this happen automatically. This is not a great solution for
virtual machines where memory hotplug is being used to address high
memory pressure situations as such onlining is slow and a userspace
process doing this (udev) has a chance of being killed by the OOM killer
as it will probably require to allocate some memory.
Introduce default policy for the newly added memory blocks in
/sys/devices/system/memory/auto_online_blocks file with two possible
values: "offline" which preserves the current behavior and "online"
which causes all newly added memory blocks to go online as soon as
they're added. The default is "offline".
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Daniel Kiper <daniel.kiper@oracle.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Tang Chen <tangchen@cn.fujitsu.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Acked-by: David Rientjes <rientjes@google.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Xishi Qiu <qiuxishi@huawei.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Kay Sievers <kay@vrfy.org>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
$ make tags
GEN tags
ctags: Warning: drivers/acpi/processor_idle.c:64: null expansion of name pattern "\1"
ctags: Warning: drivers/xen/events/events_2l.c:41: null expansion of name pattern "\1"
ctags: Warning: kernel/locking/lockdep.c:151: null expansion of name pattern "\1"
ctags: Warning: kernel/rcu/rcutorture.c:133: null expansion of name pattern "\1"
ctags: Warning: kernel/rcu/rcutorture.c:135: null expansion of name pattern "\1"
ctags: Warning: kernel/workqueue.c:323: null expansion of name pattern "\1"
ctags: Warning: net/ipv4/syncookies.c:53: null expansion of name pattern "\1"
ctags: Warning: net/ipv6/syncookies.c:44: null expansion of name pattern "\1"
ctags: Warning: net/rds/page.c:45: null expansion of name pattern "\1"
Which are all the result of the DEFINE_PER_CPU pattern:
scripts/tags.sh:200: '/\<DEFINE_PER_CPU([^,]*, *\([[:alnum:]_]*\)/\1/v/'
scripts/tags.sh:201: '/\<DEFINE_PER_CPU_SHARED_ALIGNED([^,]*, *\([[:alnum:]_]*\)/\1/v/'
The below cures them. All except the workqueue one are within reasonable
distance of the 80 char limit. TJ do you have any preference on how to
fix the wq one, or shall we just not care its too long?
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch converts xen-scsiback to modern TARGET_SCF_ACK_KREF
usage for scsiback_cmd_done() callback path.
It also also converts TMR -> scsiback_device_action() to use
modern target_submit_tmr() code.
Acked-by: Juergen Gross <jgross@suse.com>
Tested-by: Juergen Gross <jgross@suse.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch converts xen-scsiback to use percpu_ida tag
pre-allocation for struct vscsibk_pend descriptor, in
order to avoid fast-path struct vscsibk_pend memory
allocations.
Note by default this is currently hardcoded to 128.
(Add wrapper for handling pending_req tag failure - Juergen)
(Drop left-over se_cmd memset in scsiback_cmd_exec - Juergen)
Acked-by: Juergen Gross <jgross@suse.com>
Tested-by: Juergen Gross <jgross@suse.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch converts existing loopback, usb-gadget, and
xen-scsiback demo-mode only fabric drivers to use the
new target_alloc_session API caller.
This includes adding a new alloc_session callback for
fabric driver internal nexus pointer assignments.
(Fixes for early for-next nexus breakage - Dan Carpenter)
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Acked-by: Juergen Gross <jgross@suse.com>
Tested-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Tested-by: Chris Boot <bootc@bootc.net>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
- Two scsiback fixes (resource leak and spurious warning).
- Fix DMA mapping of compound pages on arm/arm64.
- Fix some pciback regressions in MSI-X handling.
- Fix a pcifront crash due to some uninitialize state.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWyvatAAoJEFxbo/MsZsTRBFcH+wWnv0/N+gKib3cKCI4lwmTg
n8iVgf8dNWwD36M2s/OlzCAglAIt8Xr6ySNvPqTerpm7lT9yXlIVQxGXTbIGuTAA
h8Kt8WiC0BNLHHlLxBuCz62KR47DvMhsr84lFURE8FmpUiulFjXmRcbrZkHIMYRS
l/X+xJWO1vxwrSYho0P9n3ksTWHm488DTPvZz3ICNI2G2sndDfbT3gv3tMDaQhcX
ZaQR93vtIoldqk29Ga59vaVtksbgxHZIbasY9PQ8rqOxHJpDQbPzpjocoLxAzf50
cioQVyKQ7i9vUvZ+B3TTAOhxisA2hDwNhLGQzmjgxe2TXeKdo3yjYwO6m1dDBzY=
=VY/S
-----END PGP SIGNATURE-----
Merge tag 'for-linus-4.5-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen bug fixes from David Vrabel:
- Two scsiback fixes (resource leak and spurious warning).
- Fix DMA mapping of compound pages on arm/arm64.
- Fix some pciback regressions in MSI-X handling.
- Fix a pcifront crash due to some uninitialize state.
* tag 'for-linus-4.5-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/pcifront: Fix mysterious crashes when NUMA locality information was extracted.
xen/pcifront: Report the errors better.
xen/pciback: Save the number of MSI-X entries to be copied later.
xen/pciback: Check PF instead of VF for PCI_COMMAND_MEMORY
xen: fix potential integer overflow in queue_reply
xen/arm: correctly handle DMA mapping of compound pages
xen/scsiback: avoid warnings when adding multiple LUNs to a domain
xen/scsiback: correct frontend counting
Commit 8135cf8b09 (xen/pciback: Save
xen_pci_op commands before processing it) broke enabling MSI-X because
it would never copy the resulting vectors into the response. The
number of vectors requested was being overwritten by the return value
(typically zero for success).
Save the number of vectors before processing the op, so the correct
number of vectors are copied afterwards.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: <stable@vger.kernel.org>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Commit 408fb0e5aa (xen/pciback: Don't
allow MSI-X ops if PCI_COMMAND_MEMORY is not set) prevented enabling
MSI-X on passed-through virtual functions, because it checked the VF
for PCI_COMMAND_MEMORY but this is not a valid bit for VFs.
Instead, check the physical function for PCI_COMMAND_MEMORY.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: <stable@vger.kernel.org>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
When len is greater than UINT_MAX - sizeof(*rb), in next allocation,
it can overflow integer range and allocates small size of heap.
After that, memcpy will overflow the allocated heap.
Therefore, it needs to check the size of given length.
Signed-off-by: Insu Yun <wuninsu@gmail.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
When adding more than one LUN to a frontend a warning for a failed
assignment is issued in dom0 for each already existing LUN. Avoid this
warning by checking for a LUN already existing when existence is
allowed (scsiback_do_add_lun() called with try == 1).
As the LUN existence check is needed now for a third time, factor it
out into a function. This in turn leads to a more or less complete
rewrite of scsiback_del_translation_entry() which will now return a
proper error code in case of failure.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
When adding a new frontend to xen-scsiback don't decrement the number
of active frontends in case of no error. Doing so results in a failure
when trying to remove the xen-pvscsi nexus even if no domain is using
it.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
The cleancache_ops structure is never modified, so declare it as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
This adds a new kind of barrier, and reworks virtio and xen
to use it.
Plus some fixes here and there.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWlU2kAAoJECgfDbjSjVRpZ6IH/Ra19ecG8sCQo9zskr4zo22Z
DZXC3u0sJDBYjjBAiw3IY1FKh7wx2Fr1RhUOj1bteBgcFCMCV1zInP5ITiCyzd1H
YYh1w9C2tZaj2T4t9L4hIrAdtIF8fGS+oI2IojXPjOuDLEt6pfFBEjHp/sfl3UJq
ZmZvw4OXviSNej7jBw8Xni3Uv18yfmLGXvMdkvMSPC1/XL29voGDqTVwhqJwxLVz
k/ZLcKFOzIs9N7Nja0Jl1EiZtC2Y9cpItqweicNAzszlpkSL44vQxmCSefB+WyQ4
gt0O3+AxYkLfrxzCBhUA4IpRex3/XPW1b+1e/V1XjfR2n/FlyLe+AIa8uPJElFc=
=ukaV
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio barrier rework+fixes from Michael Tsirkin:
"This adds a new kind of barrier, and reworks virtio and xen to use it.
Plus some fixes here and there"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: (44 commits)
checkpatch: add virt barriers
checkpatch: check for __smp outside barrier.h
checkpatch.pl: add missing memory barriers
virtio: make find_vqs() checkpatch.pl-friendly
virtio_balloon: fix race between migration and ballooning
virtio_balloon: fix race by fill and leak
s390: more efficient smp barriers
s390: use generic memory barriers
xen/events: use virt_xxx barriers
xen/io: use virt_xxx barriers
xenbus: use virt_xxx barriers
virtio_ring: use virt_store_mb
sh: move xchg_cmpxchg to a header by itself
sh: support 1 and 2 byte xchg
virtio_ring: update weak barriers to use virt_xxx
Revert "virtio_ring: Update weak barriers to use dma_wmb/rmb"
asm-generic: implement virt_xxx memory barriers
x86: define __smp_xxx
xtensa: define __smp_xxx
tile: define __smp_xxx
...
drivers/xen/events/events_fifo.c uses rmb() to communicate with the
other side.
For guests compiled with CONFIG_SMP, smp_rmb would be sufficient, so
rmb() here is only needed if a non-SMP guest runs on an SMP host.
Switch to the virt_rmb barrier which serves this exact purpose.
Pull in asm/barrier.h here to make sure the file is self-contained.
Suggested-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: David Vrabel <david.vrabel@citrix.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
drivers/xen/xenbus/xenbus_comms.c uses
full memory barriers to communicate with the other side.
For guests compiled with CONFIG_SMP, smp_wmb and smp_mb
would be sufficient, so mb() and wmb() here are only needed if
a non-SMP guest runs on an SMP host.
Switch to virt_xxx barriers which serve this exact purpose.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: David Vrabel <david.vrabel@citrix.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Add IOCTL_GNTDEV_GRANT_COPY to allow applications to copy between user
space buffers and grant references.
This interface is similar to the GNTTABOP_copy hypercall ABI except
the local buffers are provided using a virtual address (instead of a
GFN and offset). To avoid userspace from having to page align its
buffers the driver will use two or more ops if required.
If the ioctl returns 0, the application must check the status of each
segment with the segments status field. If the ioctl returns a -ve
error code (EINVAL or EFAULT), the status of individual ops is
undefined.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
This mmu_notifier_ops structure is never modified, so declare it as
const, like the other mmu_notifier_ops structures.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
The gnttab_ops structure is never modified, so declare it as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Use READ_ONCE through the code, rather than explicit barriers.
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
The dom0_op hypercall has been renamed to platform_op since Xen 3.2,
which is ancient, and modern upstream Linux kernels cannot run as dom0
and it anymore anyway.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
