LSPCON adapters in low-power state may ignore the first I2C write during
TMDS output buffer enabling, resulting in a blank screen even with an
otherwise enabled pipe. Fix this by reading back and validating the
written value a few times.
The problem was noticed on GLK machines with an onboard LSPCON adapter
after entering/exiting DC5 power state. Doing an I2C read of the adapter
ID as the first transaction - instead of the I2C write to enable the
TMDS buffers - returns the correct value. Based on this we assume that
the transaction itself is sent properly, it's only the adapter that is
not ready for some reason to accept this first write after waking from
low-power state. In my case the second I2C write attempt always
succeeded.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105854
Cc: Clinton Taylor <clinton.a.taylor@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180416155309.11100-1-imre.deak@intel.com
On Geminilake, sometimes audio card is not getting
detected after reboot. This is a spurious issue happening on
Geminilake. HW codec and HD audio controller link was going
out of sync for which there was a fix in i915 driver but
was not getting invoked for GLK. Extending this fix to GLK as well.
Tested by Du,Wenkai on GLK board.
Bspec: 21829
v2: Instead of checking GEN9_BC, BXT and GLK macros, use IS_GEN9 macro (Jani N)
Cc: <stable@vger.kernel.org> # b651bd2a3a ("drm/i915/audio: Fix audio enumeration issue on BXT")
Cc: <stable@vger.kernel.org>
Signed-off-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Reviewed-by: Abhay Kumar <abhay.Kumar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1523989338-29677-1-git-send-email-gaurav.k.singh@intel.com
(cherry picked from commit 8221229046)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
We have to cleanup after i915_perf_init(), even on the error path, as it
passes a pointer into the module to the sysfs core. If we fail to
unregister the sysctl table, we leave a dangling pointer which then may
explode anytime later.
Fixes: 9f9b2792b6 ("drm/i915/perf: reuse timestamp frequency from device info")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180414091233.32224-1-chris@chris-wilson.co.uk
(cherry picked from commit 9f172f6fbd)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
While thinking about sporadic failures of perf_pmu/rc6-runtime-pm* tests
on some CI machines I have concluded that: a) the PMU readout of RC6 can
race against runtime PM transitions, and b) there are other reasons than
being runtime suspended which can cause intel_runtime_pm_get_if_in_use to
fail.
Therefore when estimating RC6 the code needs to assert we are indeed in
suspended state, and if not, the best we can do is return the last known
RC6 value.
Without this check we can calculate the estimated value based on un-
initialized or inappropriate internal state, which can result in over-
estimation, or in any case incorrect value being returned.
v2:
* Re-arrange the code a bit to avoid second unlock and return branch.
(Chris Wilson)
v3:
* Insert some strategic blank lines and improve commit msg.
(Chris Wilson)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Fixes: 1fe699e301 ("drm/i915/pmu: Fix sleep under atomic in RC6 readout")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105010
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180410112704.24462-1-tvrtko.ursulin@linux.intel.com
(cherry picked from commit 2924bdee21)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Along the eb_lookup_vmas() error path, the return value from
kmem_cache_alloc() was freed using kfree(). Fix it to use the proper
kmem_cache_free() instead.
Fixes: d1b48c1e71 ("drm/i915: Replace execbuf vma ht with an idr")
Signed-off-by: Xidong Wang <wangxidong_97@163.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: <stable@vger.kernel.org> # v4.14+
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180404093824.9313-1-chris@chris-wilson.co.uk
(cherry picked from commit 6be1187dbf)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
In commit ce290a1960 ("selftests: add devpts selftests"), the
filesystems directory was added to the top-level selftests Makefile.
That had the effect of causing the existing dnotify_test in the
filesystems directory to now be run as part of the default selftests
test-run. Unfortunately dnotify_test is actually an infinite loop.
Fix it by moving dnotify_test to TEST_GEN_PROGS_EXTENDED, which says
that it's a generated file (ie. built) but should not be run as part
of the default test suite run (it's an "extended" test).
While we're here cleanup a few other things, devpts_pts should be in
TEST_GEN_PROGS to indicate that it's built, and with the above two
changes we no longer need a custom all or clean rule.
Fixes: ce290a1960 ("selftests: add devpts selftests")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Christian brauner <christian.brauner@ubuntu.com>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Use new return type vm_fault_t for page_mkwrite
handler.
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Reviewed-by: Matthew Wilcox <mawilcox@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
The current code null checks variable err_buf, which is always null
when it is checked, hence utf16_path is free'd and the function
returns -ENOENT everytime it is called, making it impossible for the
execution path to reach the following code:
err_buf = err_iov.iov_base;
Fix this by null checking err_iov.iov_base instead of err_buf. Also,
notice that err_buf no longer needs to be initialized to NULL.
Addresses-Coverity-ID: 1467876 ("Logically dead code")
Fixes: 2d636199e400 ("cifs: Change SMB2_open to return an iov for the error parameter")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Steve French <smfrench@gmail.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
Adding a dns_resolver key whose payload contains a very long option name
resulted in that string being printed in full. This hit the WARN_ONCE()
in set_precision() during the printk(), because printk() only supports a
precision of up to 32767 bytes:
precision 1000000 too large
WARNING: CPU: 0 PID: 752 at lib/vsprintf.c:2189 vsnprintf+0x4bc/0x5b0
Fix it by limiting option strings (combined name + value) to a much more
reasonable 128 bytes. The exact limit is arbitrary, but currently the
only recognized option is formatted as "dnserror=%lu" which fits well
within this limit.
Also ratelimit the printks.
Reproducer:
perl -e 'print "#", "A" x 1000000, "\x00"' | keyctl padd dns_resolver desc @s
This bug was found using syzkaller.
Reported-by: Mark Rutland <mark.rutland@arm.com>
Fixes: 4a2d789267 ("DNS: If the DNS server returns an error, allow that to be cached [ver #2]")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For some firmware variants - specifically 'capture packed stream' - RSS
filters are not valid. We must check if RSS is actually active rather
than merely enabled.
Fixes: 42356d9a13 ("sfc: support RSS spreading of ethtool ntuple filters")
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Validate the topology input before we dereference the pointer.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
struct tvec_base is a leftover of the original timer wheel implementation
and not longer used. Remove the forward declaration.
Signed-off-by: Liu Changcheng <changcheng.liu@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: akpm@linux-foundation.org
Link: https://lkml.kernel.org/r/20180412075701.GA38952@sofia
Convert the clockevents driver from old-style printk() to pr_info() and
pr_cont(), to fix split kernel messages like below:
Clockevents: could not switch to one-shot mode:
dummy_timer is not functional.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Link: https://lkml.kernel.org/r/1522942018-14471-1-git-send-email-geert%2Brenesas@glider.be
The __clear_user function is defined to return the number of bytes that
could not be cleared. From the underlying memset / bzero implementation
this means setting register a2 to that number on return. Currently if a
page fault is triggered within the memset_partial block, the value
loaded into a2 on return is meaningless.
The label .Lpartial_fixup\@ is jumped to on page fault. In order to work
out how many bytes failed to copy, the exception handler should find how
many bytes left in the partial block (andi a2, STORMASK), add that to
the partial block end address (a2), and subtract the faulting address to
get the remainder. Currently it incorrectly subtracts the partial block
start address (t1), which has additionally been clobbered to generate a
jump target in memset_partial. Fix this by adding the block end address
instead.
This issue was found with the following test code:
int j, k;
for (j = 0; j < 512; j++) {
if ((k = clear_user(NULL, j)) != j) {
pr_err("clear_user (NULL %d) returned %d\n", j, k);
}
}
Which now passes on Creator Ci40 (MIPS32) and Cavium Octeon II (MIPS64).
Suggested-by: James Hogan <jhogan@kernel.org>
Signed-off-by: Matt Redfearn <matt.redfearn@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/19108/
Signed-off-by: James Hogan <jhogan@kernel.org>
To ensure that qrtr can be loaded automatically, when needed, if it is compiled
as module.
Signed-off-by: Nicolas Dechesne <nicolas.dechesne@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit c1eef220c1 ("vsock: always call
vsock_init_tables()") introduced a module_init() function without a
corresponding module_exit() function.
Modules with an init function can only be removed if they also have an
exit function. Therefore the vsock module was considered "permanent"
and could not be removed.
This patch adds an empty module_exit() function so that "rmmod vsock"
works. No explicit cleanup is required because:
1. Transports call vsock_core_exit() upon exit and cannot be removed
while sockets are still alive.
2. vsock_diag.ko does not perform any action that requires cleanup by
vsock.ko.
Fixes: c1eef220c1 ("vsock: always call vsock_init_tables()")
Reported-by: Xiumei Mu <xmu@redhat.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Jorgen Hansen <jhansen@vmware.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Jorgen Hansen <jhansen@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Intel's Skylake Server CPUs have a different LLC topology than previous
generations. When in Sub-NUMA-Clustering (SNC) mode, the package is divided
into two "slices", each containing half the cores, half the LLC, and one
memory controller and each slice is enumerated to Linux as a NUMA
node. This is similar to how the cores and LLC were arranged for the
Cluster-On-Die (CoD) feature.
CoD allowed the same cache line to be present in each half of the LLC.
But, with SNC, each line is only ever present in *one* slice. This means
that the portion of the LLC *available* to a CPU depends on the data being
accessed:
Remote socket: entire package LLC is shared
Local socket->local slice: data goes into local slice LLC
Local socket->remote slice: data goes into remote-slice LLC. Slightly
higher latency than local slice LLC.
The biggest implication from this is that a process accessing all
NUMA-local memory only sees half the LLC capacity.
The CPU describes its cache hierarchy with the CPUID instruction. One of
the CPUID leaves enumerates the "logical processors sharing this
cache". This information is used for scheduling decisions so that tasks
move more freely between CPUs sharing the cache.
But, the CPUID for the SNC configuration discussed above enumerates the LLC
as being shared by the entire package. This is not 100% precise because the
entire cache is not usable by all accesses. But, it *is* the way the
hardware enumerates itself, and this is not likely to change.
The userspace visible impact of all the above is that the sysfs info
reports the entire LLC as being available to the entire package. As noted
above, this is not true for local socket accesses. This patch does not
correct the sysfs info. It is the same, pre and post patch.
The current code emits the following warning:
sched: CPU #3's llc-sibling CPU #0 is not on the same node! [node: 1 != 0]. Ignoring dependency.
The warning is coming from the topology_sane() check in smpboot.c because
the topology is not matching the expectations of the model for obvious
reasons.
To fix this, add a vendor and model specific check to never call
topology_sane() for these systems. Also, just like "Cluster-on-Die" disable
the "coregroup" sched_domain_topology_level and use NUMA information from
the SRAT alone.
This is OK at least on the hardware we are immediately concerned about
because the LLC sharing happens at both the slice and at the package level,
which are also NUMA boundaries.
Signed-off-by: Alison Schofield <alison.schofield@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Borislav Petkov <bp@suse.de>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: brice.goglin@gmail.com
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: David Rientjes <rientjes@google.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: "H. Peter Anvin" <hpa@linux.intel.com>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Link: https://lkml.kernel.org/r/20180407002130.GA18984@alison-desk.jf.intel.com
If the get_callchain_buffers fails to allocate the buffer it will
decrease the nr_callchain_events right away.
There's no point of checking the allocation error for
nr_callchain_events > 1. Removing that check.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: syzkaller-bugs@googlegroups.com
Cc: x86@kernel.org
Link: http://lkml.kernel.org/r/20180415092352.12403-3-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The syzbot hit KASAN bug in perf_callchain_store having the entry stored
behind the allocated bounds [1].
We miss the sample_max_stack check for the initial event that allocates
callchain buffers. This missing check allows to create an event with
sample_max_stack value bigger than the global sysctl maximum:
# sysctl -a | grep perf_event_max_stack
kernel.perf_event_max_stack = 127
# perf record -vv -C 1 -e cycles/max-stack=256/ kill
...
perf_event_attr:
size 112
...
sample_max_stack 256
------------------------------------------------------------
sys_perf_event_open: pid -1 cpu 1 group_fd -1 flags 0x8 = 4
Note the '-C 1', which forces perf record to create just single event.
Otherwise it opens event for every cpu, then the sample_max_stack check
fails on the second event and all's fine.
The fix is to run the sample_max_stack check also for the first event
with callchains.
[1] https://marc.info/?l=linux-kernel&m=152352732920874&w=2
Reported-by: syzbot+7c449856228b63ac951e@syzkaller.appspotmail.com
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: syzkaller-bugs@googlegroups.com
Cc: x86@kernel.org
Fixes: 97c79a38cd ("perf core: Per event callchain limit")
Link: http://lkml.kernel.org/r/20180415092352.12403-2-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Return immediately when we find issue in the user stack checks. The
error value could get overwritten by following check for
PERF_SAMPLE_REGS_INTR.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: syzkaller-bugs@googlegroups.com
Cc: x86@kernel.org
Fixes: 60e2364e60 ("perf: Add ability to sample machine state on interrupt")
Link: http://lkml.kernel.org/r/20180415092352.12403-1-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
'perf list' with flags -d and -v print a description (-d) or a very
verbose explanation (-v) of CPU specific counter events. These
descriptions are provided with the json files in directory
pmu-events/arch/s390/*.json.
Display of these descriptions on s390 requires the corresponding json
files.
On s390 this does not work because function is_pmu_core() does not
detect the s390 directory name where the CPU specific events are listed.
On x86 it is:
/sys/bus/event_source/devices/cpu
whereas on s390 it is:
/sys/bus/event_source/devices/cpum_cf
/sys/bus/event_source/devices/cpum_sf
Fix this by adding s390 directory name testing to function
is_pmu_core(). This is the same approach as taken for the ARM platform.
Output before:
[root@s35lp76 perf]# ./perf list -d pmu
List of pre-defined events (to be used in -e):
cpum_cf/AES_BLOCKED_CYCLES/ [Kernel PMU event]
cpum_cf/AES_BLOCKED_FUNCTIONS/ [Kernel PMU event]
cpum_cf/AES_CYCLES/ [Kernel PMU event]
cpum_cf/AES_FUNCTIONS/ [Kernel PMU event]
....
cpum_cf/TX_NC_TEND/ [Kernel PMU event]
cpum_cf/VX_BCD_EXECUTION_SLOTS/ [Kernel PMU event]
cpum_sf/SF_CYCLES_BASIC/ [Kernel PMU event]
Output after:
[root@s35lp76 perf]# ./perf list -d pmu
List of pre-defined events (to be used in -e):
cpum_cf/AES_BLOCKED_CYCLES/ [Kernel PMU event]
cpum_cf/AES_BLOCKED_FUNCTIONS/ [Kernel PMU event]
cpum_cf/AES_CYCLES/ [Kernel PMU event]
cpum_cf/AES_FUNCTIONS/ [Kernel PMU event]
....
cpum_cf/TX_NC_TEND/ [Kernel PMU event]
cpum_cf/VX_BCD_EXECUTION_SLOTS/ [Kernel PMU event]
cpum_sf/SF_CYCLES_BASIC/ [Kernel PMU event]
3906:
bcd_dfp_execution_slots
[BCD DFP Execution Slots]
decimal_instructions
[Decimal Instructions]
dtlb2_gpage_writes
[DTLB2 GPAGE Writes]
dtlb2_hpage_writes
[DTLB2 HPAGE Writes]
dtlb2_misses
[DTLB2 Misses]
dtlb2_writes
[DTLB2 Writes]
itlb2_misses
[ITLB2 Misses]
itlb2_writes
[ITLB2 Writes]
l1c_tlb2_misses
[L1C TLB2 Misses]
.....
cfvn 3:
cpu_cycles
[CPU Cycles]
instructions
[Instructions]
l1d_dir_writes
[L1D Directory Writes]
l1d_penalty_cycles
[L1D Penalty Cycles]
l1i_dir_writes
[L1I Directory Writes]
l1i_penalty_cycles
[L1I Penalty Cycles]
problem_state_cpu_cycles
[Problem State CPU Cycles]
problem_state_instructions
[Problem State Instructions]
....
csvn generic:
aes_blocked_cycles
[AES Blocked Cycles]
aes_blocked_functions
[AES Blocked Functions]
aes_cycles
[AES Cycles]
aes_functions
[AES Functions]
dea_blocked_cycles
[DEA Blocked Cycles]
dea_blocked_functions
[DEA Blocked Functions]
....
Signed-off-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Reviewed-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Link: http://lkml.kernel.org/r/20180416132314.33249-1-tmricht@linux.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Store preempting context switch out event into Perf trace as a part of
PERF_RECORD_SWITCH[_CPU_WIDE] record.
Percentage of preempting and non-preempting context switches help
understanding the nature of workloads (CPU or IO bound) that are running
on a machine;
The event is treated as preemption one when task->state value of the
thread being switched out is TASK_RUNNING. Event type encoding is
implemented using PERF_RECORD_MISC_SWITCH_OUT_PREEMPT bit;
Signed-off-by: Alexey Budankov <alexey.budankov@linux.intel.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: http://lkml.kernel.org/r/9ff84e83-a0ca-dd82-a6d0-cb951689be74@linux.intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Sync the following tooling headers with the latest kernel version:
tools/arch/arm/include/uapi/asm/kvm.h
- New ABI: KVM_REG_ARM_*
tools/arch/x86/include/asm/required-features.h
- Removal of NEED_LA57 dependency
tools/arch/x86/include/uapi/asm/kvm.h
- New KVM ABI: KVM_SYNC_X86_*
tools/include/uapi/asm-generic/mman-common.h
- New ABI: MAP_FIXED_NOREPLACE flag
tools/include/uapi/linux/bpf.h
- New ABI: BPF_F_SEQ_NUMBER functions
tools/include/uapi/linux/if_link.h
- New ABI: IFLA tun and rmnet support
tools/include/uapi/linux/kvm.h
- New ABI: hyperv eventfd and CONN_ID_MASK support plus header cleanups
tools/include/uapi/sound/asound.h
- New ABI: SNDRV_PCM_FORMAT_FIRST PCM format specifier
tools/perf/arch/x86/entry/syscalls/syscall_64.tbl
- The x86 system call table description changed due to the ptregs changes and the renames, in:
d5a00528b5: syscalls/core, syscalls/x86: Rename struct pt_regs-based sys_*() to __x64_sys_*()
5ac9efa3c5: syscalls/core, syscalls/x86: Clean up compat syscall stub naming convention
ebeb8c82ff: syscalls/x86: Use 'struct pt_regs' based syscall calling for IA32_EMULATION and x32
Also fix the x86 syscall table warning:
-Warning: Kernel ABI header at 'tools/arch/x86/entry/syscalls/syscall_64.tbl' differs from latest version at 'arch/x86/entry/syscalls/syscall_64.tbl'
+Warning: Kernel ABI header at 'tools/perf/arch/x86/entry/syscalls/syscall_64.tbl' differs from latest version at 'arch/x86/entry/syscalls/syscall_64.tbl'
None of these changes impact existing tooling code, so we only have to copy the kernel version.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Alexei Starovoitov <alexei.starovoitov@gmail.com>
Cc: Alexey Budankov <alexey.budankov@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Brian Robbins <brianrob@microsoft.com>
Cc: Clark Williams <williams@redhat.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: David Ahern <dsahern@gmail.com>
Cc: Dmitriy Vyukov <dvyukov@google.com> <dvyukov@google.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Cc: Jesper Dangaard Brouer <brouer@redhat.com>
Cc: Jin Yao <yao.jin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Kim Phillips <kim.phillips@arm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Li Zhijian <lizhijian@cn.fujitsu.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Martin Liška <mliska@suse.cz>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matthias Kaehlcke <mka@chromium.org>
Cc: Miguel Bernal Marin <miguel.bernal.marin@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ravi Bangoria <ravi.bangoria@linux.vnet.ibm.com>
Cc: Sandipan Das <sandipan@linux.vnet.ibm.com>
Cc: Stephane Eranian <eranian@google.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Takuya Yamamoto <tkydevel@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Thomas Richter <tmricht@linux.ibm.com>
Cc: Wang Nan <wangnan0@huawei.com>
Cc: William Cohen <wcohen@redhat.com>
Cc: Yonghong Song <yhs@fb.com>
Link: http://lkml.kernel.org/r/20180416064024.ofjtrz5yuu3ykhvl@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
xenbus_command_reply() did not actually copy the response string and
leaked stack content instead.
Fixes: 9a6161fe73 ("xen: return xenstore command failures via response instead of rc")
Signed-off-by: Simon Gaiser <simon@invisiblethingslab.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
This is the sync up with the canonical definition of the sound
protocol in Xen:
1. Protocol version was referenced in the protocol description,
but missed its definition. Fixed by adding a constant
for current protocol version.
2. Some of the request descriptions have "reserved" fields
missed: fixed by adding corresponding entries.
3. Extend the size of the requests and responses to 64 octets.
Bump protocol version to 2.
4. Add explicit back and front synchronization
In order to provide explicit synchronization between backend and
frontend the following changes are introduced in the protocol:
- add new ring buffer for sending asynchronous events from
backend to frontend to report number of bytes played by the
frontend (XENSND_EVT_CUR_POS)
- introduce trigger events for playback control: start/stop/pause/resume
- add "req-" prefix to event-channel and ring-ref to unify naming
of the Xen event channels for requests and events
5. Add explicit back and front parameter negotiation
In order to provide explicit stream parameter negotiation between
backend and frontend the following changes are introduced in the protocol:
add XENSND_OP_HW_PARAM_QUERY request to read/update
configuration space for the parameters given: request passes
desired parameter's intervals/masks and the response to this request
returns allowed min/max intervals/masks to be used.
Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Signed-off-by: Oleksandr Grytsov <oleksandr_grytsov@epam.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
We might need to do some actions before the shadow variable is freed.
For example, we might need to remove it from a list or free some data
that it points to.
This is already possible now. The user can get the shadow variable
by klp_shadow_get(), do the necessary actions, and then call
klp_shadow_free().
This patch allows to do it a more elegant way. The user could implement
the needed actions in a callback that is passed to klp_shadow_free()
as a parameter. The callback usually does reverse operations to
the constructor callback that can be called by klp_shadow_*alloc().
It is especially useful for klp_shadow_free_all(). There we need to do
these extra actions for each found shadow variable with the given ID.
Note that the memory used by the shadow variable itself is still released
later by rcu callback. It is needed to protect internal structures that
keep all shadow variables. But the destructor is called immediately.
The shadow variable must not be access anyway after klp_shadow_free()
is called. The user is responsible to protect this any suitable way.
Be aware that the destructor is called under klp_shadow_lock. It is
the same as for the contructor in klp_shadow_alloc().
Signed-off-by: Petr Mladek <pmladek@suse.com>
Acked-by: Josh Poimboeuf <jpoimboe@redhat.com>
Acked-by: Miroslav Benes <mbenes@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The existing API allows to pass a sample data to initialize the shadow
data. It works well when the data are position independent. But it fails
miserably when we need to set a pointer to the shadow structure itself.
Unfortunately, we might need to initialize the pointer surprisingly
often because of struct list_head. It is even worse because the list
might be hidden in other common structures, for example, struct mutex,
struct wait_queue_head.
For example, this was needed to fix races in ALSA sequencer. It required
to add mutex into struct snd_seq_client. See commit b3defb791b
("ALSA: seq: Make ioctls race-free") and commit d15d662e89
("ALSA: seq: Fix racy pool initializations")
This patch makes the API more safe. A custom constructor function and data
are passed to klp_shadow_*alloc() functions instead of the sample data.
Note that ctor_data are no longer a template for shadow->data. It might
point to any data that might be necessary when the constructor is called.
Also note that the constructor is called under klp_shadow_lock. It is
an internal spin_lock that synchronizes alloc() vs. get() operations,
see klp_shadow_get_or_alloc(). On one hand, this adds a risk of ABBA
deadlocks. On the other hand, it allows to do some operations safely.
For example, we could add the new structure into an existing list.
This must be done only once when the structure is allocated.
Reported-by: Nicolai Stange <nstange@suse.de>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Acked-by: Josh Poimboeuf <jpoimboe@redhat.com>
Acked-by: Miroslav Benes <mbenes@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
In snd_soc_tplg_component_remove(), it should compare index and
not dobj->index with SND_SOC_TPLG_INDEX_ALL for removing all
topology objects.
Signed-off-by: Yan Wang <yan.wang@linux.intel.com>
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Yet another slight code cleanup: there are two places where
calculating the PCM delay, and they can be unified in a single
helper. It reduces the multiple open codes.
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
RongQing reported that there are some X2APIC id 0xffffffff in his machine's
ACPI MADT table, which makes the number of possible CPU inaccurate.
The reason is that the ACPI X2APIC parser has no sanity check for APIC ID
0xffffffff, which is an invalid id in all APIC types. See "Intel® 64
Architecture x2APIC Specification", Chapter 2.4.1.
Add a sanity check to acpi_parse_x2apic() which ignores the invalid id.
Reported-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: Dou Liyang <douly.fnst@cn.fujitsu.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Cc: len.brown@intel.com
Cc: rjw@rjwysocki.net
Cc: hpa@zytor.com
Link: https://lkml.kernel.org/r/20180412014052.25186-1-douly.fnst@cn.fujitsu.com
The TSC calibration code uses HPET as reference. The conversion normalizes
the delta of two HPET timestamps:
hpetref = ((tshpet1 - tshpet2) * HPET_PERIOD) / 1e6
and then divides the normalized delta of the corresponding TSC timestamps
by the result to calulate the TSC frequency.
tscfreq = ((tstsc1 - tstsc2 ) * 1e6) / hpetref
This uses do_div() which takes an u32 as the divisor, which worked so far
because the HPET frequency was low enough that 'hpetref' never exceeded
32bit.
On Skylake machines the HPET frequency increased so 'hpetref' can exceed
32bit. do_div() truncates the divisor, which causes the calibration to
fail.
Use div64_u64() to avoid the problem.
[ tglx: Fixes whitespace mangled patch and rewrote changelog ]
Signed-off-by: Xiaoming Gao <newtongao@tencent.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Cc: peterz@infradead.org
Cc: hpa@zytor.com
Link: https://lkml.kernel.org/r/38894564-4fc9-b8ec-353f-de702839e44e@gmail.com
If there is no d-cache-size property in the device tree, l1d_size could
be zero. We don't actually expect that to happen, it's only been seen
on mambo (simulator) in some configurations.
A zero-size l1d_size leads to the loop in the asm wrapping around to
2^64-1, and then walking off the end of the fallback area and
eventually causing a page fault which is fatal.
Just default to 64K which is correct on some CPUs, and sane enough to
not cause a crash on others.
Fixes: aa8a5e0062 ('powerpc/64s: Add support for RFI flush of L1-D cache')
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
[mpe: Rewrite comment and change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The struct sigaction for user space in arch/s390/include/uapi/asm/signal.h
is ill defined. The kernel uses two structures 'struct sigaction' and
'struct old_sigaction', the correlation in the kernel for both 31 and
64 bit is as follows
sys_sigaction -> struct old_sigaction
sys_rt_sigaction -> struct sigaction
The correlation of the (single) uapi definition for 'struct sigaction'
under '#ifndef __KERNEL__':
31-bit: sys_sigaction -> uapi struct sigaction
31-bit: sys_rt_sigaction -> no structure available
64-bit: sys_sigaction -> no structure available
64-bit: sys_rt_sigaction -> uapi struct sigaction
This is quite confusing. To make it a bit less confusing make the
uapi definition of 'struct sigaction' usable for sys_rt_sigaction for
both 31-bit and 64-bit.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
It may be useful to compile host programs with different flags (e.g.
hardening). Ensure that objtool picks up the appropriate flags.
Signed-off-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kbuild@vger.kernel.org
Link: http://lkml.kernel.org/r/05a360681176f1423cb2fde8faae3a0a0261afc5.1523560825.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Now exynos_drm_fb is just an empty wrapper around drm_framebuffer, we
can drop it.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: Seung-Woo Kim <sw0312.kim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
This can be calculated from the GEM BO DMA address as well as the offset
stored in the base framebuffer.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: Seung-Woo Kim <sw0312.kim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Since drm_framebuffer can now store GEM objects directly, place them
there rather than in our own subclass. As this makes the framebuffer
create_handle and destroy functions the same as the GEM framebuffer
helper, we can reuse those.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: Seung-Woo Kim <sw0312.kim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
This warning message is not very helpful, as the return value should
already show information about the error. Also, this message will
spam dmesg if the user space does testing in a loop, like:
for x in {0..5}
do
echo p:xx xx+$x >> /sys/kernel/debug/tracing/kprobe_events
done
Reported-by: Vince Weaver <vincent.weaver@maine.edu>
Signed-off-by: Song Liu <songliubraving@fb.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: kernel-team@fb.com
Link: http://lkml.kernel.org/r/20180413185513.3626052-1-songliubraving@fb.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The poll callbacks for playback and capture directions are doing
fairly similar but with a slight difference. This patch unifies the
two functions into a single callback. The advantage of this
refactoring is that the direction-specific procedures become clearer.
There should be no functional change but only the code cleanup.
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Introduce two new direction-neutral helpers to calculate the avail and
hw_avail values, and clean up the code with them.
The two separated forward and rewind functions are gathered to the
unified functions.
No functional change but only code reductions.
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
