When allocating from the reserved tags pool, bt_get() is called with
a NULL hctx. If all tags are in use, the hw queue is kicked to push
out any pending IO, potentially freeing tags, and tag allocation is
retried. The problem is that blk_mq_run_hw_queue() doesn't check for
a NULL hctx. So we avoid it with a simple NULL hctx test.
Tested by hammering mtip32xx with concurrent smartctl/hdparm.
Signed-off-by: Sam Bradshaw <sbradshaw@micron.com>
Signed-off-by: Selvan Mani <smani@micron.com>
Fixes: b32232073e ("blk-mq: fix hang in bt_get()")
Cc: stable@kernel.org
Added appropriate comment.
Signed-off-by: Jens Axboe <axboe@fb.com>
Commit 7800064ba5 ("ARM: dts: Add basic dm816x device tree
configuration") added basic devices for dm816x, but I was not able
to test the GPIO interrupts earlier until I found some suitable pins
to test with. We can mux the MMC card detect and write protect pins
from SD_SDCD and SD_SDWP mode to use a normal GPIO interrupts that
are also suitable for the MMC subsystem.
This turned out several issues that need to be fixed:
- I set the GPIO type wrong to be compatible with omap3 instead
of omap4. The GPIO controller on dm816x has EOI interrupt
register like omap4 and am335x.
- I got the GPIO interrupt numbers wrong as each bank has two
and we only use one. They need to be set up the same way as
on am335x.
- The gpio banks are missing interrupt controller related
properties.
With these changes the GPIO interrupts can be used with the
MMC card detect pin, so let's wire that up. Let's also mux all
the MMC lines for completeness while at it.
For the first GPIO bank I tested using GPMC lines temporarily
muxed to GPIOs on the dip switch 10.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Now that we don't have hwmod entry for pcie PHY remove the
ti,hwmod property from PCIE PHY's. Otherwise we will get:
platform 4a094000.pciephy: Cannot lookup hwmod 'pcie1-phy'
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Or Gerlitz says:
====================
mlx4 driver fixes for 4.0-rc
Just few small fixes for the 4.0 rc cycle.
The fix from Moni addresses an issue from 4.0-rc1 so we
just need it for net.
Eran's fix for off-by-one should go to 3.19.y too.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Port statistics bitmap will now be initialized at port init. Even before
starting the port, statistics are visible to the user and must be properly masked.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For RoCE ports, we set the u32 PMA values based on u64 HCA counters. In case of
overflow, according to the IB spec, we have to saturate a counter to its
max value, do that.
Fixes: c37791349c ('IB/mlx4: Support PMA counters for IBoE')
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NUM_PORT_STATS was 9 instead of 10, which caused off-by-one bug when
displaying the statistics starting from tx_chksum_offload in ethtool.
Fixes: f8c6455bb0 ('net/mlx4_en: Extend checksum offloading by CHECKSUM COMPLETE')
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Processing an event is done in a different context from the one when
the event was dispatched. This requires a check that the slave
net device is still valid when the event is being processed. The check is done
under the iboe lock which ensure correctness.
Fixes: a575009030 ('IB/mlx4: Add port aggregation support')
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a collection of many small fixes. Most of fixes are for ASoC
drivers, including the fixes of wrong field usages for boolean kctls.
In addition, there is a fix in ASoC core for adding proper locks for
component lists, and a fix for a HD-audio regression by the previous
mono channel fix.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=CDXF
-----END PGP SIGNATURE-----
Merge tag 'sound-4.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This is a collection of many small fixes. Most of fixes are for ASoC
drivers, including the fixes of wrong field usages for boolean kctls.
In addition, there is a fix in ASoC core for adding proper locks for
component lists, and a fix for a HD-audio regression by the previous
mono channel fix"
* tag 'sound-4.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (24 commits)
ALSA: hda - Treat stereo-to-mono mix properly
ASoC: wm9713: Fix wrong value references for boolean kctl
ASoC: wm9712: Fix wrong value references for boolean kctl
ASoC: wm8960: Fix wrong value references for boolean kctl
ASoC: wm8955: Fix wrong value references for boolean kctl
ASoC: wm8904: Fix wrong value references for boolean kctl
ASoC: wm8903: Fix wrong value references for boolean kctl
ASoC: wm8731: Fix wrong value references for boolean kctl
ASoC: wm2000: Fix wrong value references for boolean kctl
ASoC: tas5086: Fix wrong value references for boolean kctl
ASoC: pcm1681: Fix wrong value references for boolean kctl
ASoC: es8238: Fix wrong value references for boolean kctl
ASoC: cs4271: Fix wrong value references for boolean kctl
ASoC: ak4641: Fix wrong value references for boolean kctl
ASoC: adav80x: Fix wrong value references for boolean kctl
ASoC: Fix component lists locking
ASoC: Intel: remove conflicts when load/unload multiple firmware images
ASoC: rt286: Change the DMI mapping for Dino
ASoC: sgtl5000: remove useless register write clearing CHRGPUMP_POWERUP
ASoC: fsl_ssi: Don't try to round-up for PM divisor calculation
...
Pull crypto fixes from Herbert Xu:
"Fix a bug in the ARM XTS implementation that can cause failures in
decrypting encrypted disks, and fix is a memory overwrite bug that can
cause a crash which can be triggered from userspace"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: aesni - fix memory usage in GCM decryption
crypto: arm/aes update NEON AES module to latest OpenSSL version
Pull livepatching fix from Jiri Kosina:
- fix for potential race with module loading, from Petr Mladek.
The race is very unlikely to be seen in real world and has been found
by code inspection, but should be fixed for 4.0 anyway.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/livepatching:
livepatch: Fix subtle race with coming and going modules
Pull HID fixes from Jiri Kosina:
- fixes for pen pen proximity / touch events in wacom driver, from Ping
Cheng and Benjamin Tissoires
- two new device-specific quirks from Oliver Neukum and Forest
Wilkinson
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: wacom: check for wacom->shared before following the pointer
HID: tivo: enable all buttons on the TiVo Slide Pro remote
HID: add ALWAYS_POLL quirk for a Logitech 0xc007
HID: wacom: rely on actual touch down count to decide touch_down
HID: wacom: do not send pen events before touch is up/forced out
Ensure that clients can automatically configure themselves and avoid a
nasty warning at boot by providing capability information.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We should signal connect (pull up dp) after we have already
at peripheral mode, otherwise, the dp may be toggled due to
we reset controller or do disconnect during the initialization
for peripheral, then, the host may be confused during the
enumeration, eg, it finds the reset can't succeed, but the
device is still there, see below error message.
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?
hub 1-0:1.0: unable to enumerate USB device on port 1
Fixes: the issue existed when the otg fsm code was added.
Cc: <stable@vger.kernel.org> # v3.16+
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A new uas compatible controller has shown up in some people's devices from
the manufacturer Initio Corporation, this controller needs the US_FL_NO_ATA_1X
quirk to work properly with uas, so add it to the uas quirks table.
Reported-and-tested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
radeon_bo_create() calls radeon_ttm_placement_from_domain()
before ttm_bo_init() is called. radeon_ttm_placement_from_domain()
uses the ttm bo size to determine when to select top down
allocation but since the ttm bo is not initialized yet the
check is always false. It only took effect when buffers
were validated later. It also seemed to regress suspend
and resume on some systems possibly due to it not
taking effect in radeon_bo_create().
radeon_bo_create() and radeon_ttm_placement_from_domain()
need to be reworked substantially for this to be optimally
effective. Re-enable it at that point.
Noticed-by: Oded Gabbay <oded.gabbay@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
The EHCI IP only needs the UTMI/UPLL (uclk) and the peripheral (iclk)
clocks to work properly. Remove the useless system clock (fclk).
Avoid calling set_rate on the fixed rate UTMI/IPLL clock and remove
useless IS_ENABLED(CONFIG_COMMON_CLK) tests (all at91 platforms have been
moved to the CCF).
This patch also fixes a bug introduced by 3440ef1 (ARM: at91/dt: fix USB
high-speed clock to select UTMI), which was leaving the usb clock
uninitialized and preventing the OHCI driver from setting the usb clock
rate to 48MHz.
This bug was caused by several things:
1/ usb clock drivers set the CLK_SET_RATE_GATE flag, which means the rate
cannot be changed once the clock is prepared
2/ The EHCI driver was retrieving and preparing/enabling the uhpck
clock which was in turn preparing its parent clock (the usb clock),
thus preventing any rate change because of 1/
Fixes: 3440ef1691 ("ARM: at91/dt: fix USB high-speed clock to select UTMI")
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit "drm/exynos: remove exynos_plane_dpms" (d9ea6256) removed the
use of the enabled flag, which means that the code may attempt to call
win_enable on a NULL crtc. This results in the following oops on
Arndale:
[ 1.673479] Unable to handle kernel NULL pointer dereference at virtual address 00000368
[ 1.681500] pgd = c0004000
[ 1.684154] [00000368] *pgd=00000000
[ 1.687713] Internal error: Oops: 5 [#1] PREEMPT SMP ARM
[ 1.693012] Modules linked in:
[ 1.696045] CPU: 1 PID: 1 Comm: swapper/0 Not tainted
3.19.0-07545-g57485fa #1907
[ 1.703524] Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
(....)
[ 2.014803] [<c02f9cfc>] (exynos_plane_destroy) from [<c02e61b4>] (drm_mode_config_cleanup+0x168/0x20c)
[ 2.024178] [<c02e61b4>] (drm_mode_config_cleanup) from [<c02f66fc>] (exynos_drm_load+0xac/0x12c)
This patch adds in a check to ensure exynos_crtc is not NULL before it
is dereferenced.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
With spidev the mesg->complete callback points to spidev_complete.
Calling this unblocks spidev_sync and so spidev_sync_write finishes. As
the struct spi_message just read is a local variable in
spidev_sync_write and recording the trace event accesses this message
the recording is better done first. The same can happen for
spidev_sync_read.
This fixes an oops observed on a 3.14-rt system with spidev activity
after
echo 1 > /sys/kernel/debug/tracing/events/spi/enable
.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Replace inline asm statement in __get_cpu_architecture() with equivalent
macro invocation, i.e. read_cpuid_ext(CPUID_EXT_MMFR0);
As an added bonus, this squashes a potential bug, described by Paul
Walmsley in commit 067e710b9a ("ARM: 7801/1: prevent gcc 4.5 from
reordering extended CP15 reads above is_smp() test").
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The set_memory_* functions currently only support module
addresses. The addresses are validated using is_module_addr.
That function is special though and relies on internal state
in the module subsystem to work properly. At the time of
module initialization and calling set_memory_*, it's too early
for is_module_addr to work properly so it always returns
false. Rather than be subject to the whims of the module state,
just bounds check against the module virtual address range.
Signed-off-by: Laura Abbott <lauraa@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Allow prefetch settings overriding by device tree, in case
l2x0_cache_size_of_parse() returns value, prefetch tuning
properties are silently ignored. E.g. arm,double-linefill* and
arm,prefetch*.
This happens for example, when "cache-size" or "cache-sets"
properties haven't been filled in l2c dt node.
Comments from Fabrice Gasnier:
Allow device tree to override the L2C prefetch settings, even when
l2x0_cache_size_of_parse() fails to parse the cache geometry due to (eg)
missing "cache-size" or "cache-sets" properties.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On sun4i-a10, when GPIOs are configured as external interrupt the value for
them in the data register does not seem to get updated, so set their mux to
input (and restore afterwards) when reading the pin.
Missed edges seem to be buffered, so this does not introduce a race
condition.
I've also tested this on sun5i-a13 and sun7i-a20 and those do not seem to
be affected, the input value representation in the data register does seem
to correctly get updated to the actual pin value while in irq mode there.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
After importing multi-lower layer support, users could mount a r/o
partition as the left most lowerdir instead of using it as upperdir.
And a r/o upperdir may cause an error like
overlayfs: failed to create directory ./workdir/work
during mount.
This patch check the *s_flags* of upper fs and return an error if
it is a r/o partition. The checking of *upper_mnt->mnt_sb->s_flags*
can be removed now.
This patch also remove
/* FIXME: workdir is not needed for a R/O mount */
from ovl_fill_super() because:
1) for upper fs r/o case
Setting a r/o partition as upper is prevented, no need to care about
workdir in this case.
2) for "mount overlay -o ro" with a r/w upper fs case
Users could remount overlayfs to r/w in this case, so workdir should
not be omitted.
Signed-off-by: hujianyang <hujianyang@huawei.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Recently multi-lower layer mount support allow upperdir and workdir
to be omitted, then cause overlayfs can be mount with only one
lowerdir directory. This action make no sense and have potential risk.
This patch check the total number of lower directories to prevent
mounting overlayfs with only one directory.
Also, an error message is added to indicate lower directories exceed
OVL_MAX_STACK limit.
Signed-off-by: hujianyang <hujianyang@huawei.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Overlayfs should print an error message if an incorrect mount option
is caught like other filesystems.
After this patch, improper option input could be clearly known.
Reported-by: Fabian Sturm <fabian.sturm@aduu.de>
Signed-off-by: hujianyang <hujianyang@huawei.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
We don't want to end up in a state where we track that the pipe has its
primary plane enabled when primary plane registers are programmed with
values that look possible but the plane actually disabled.
Refuse to read out the fb state when the primary plane isn't enabled.
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Suggested-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reported-by: Andrey Skvortsov <andrej.skvortzov@gmail.com>
Reported-by: Steven Rostedt <rostedt@goodmis.org>
Reference: http://mid.gmane.org/20150203191507.GA2374@crion86
Tested-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Revisiting commit d23b8ad8ab ("tc: add BPF based action") with regards
to eBPF support, I was thinking that it might be better to improve
return semantics from a BPF program invoked through BPF_PROG_RUN().
Currently, in case filter_res is 0, we overwrite the default action
opcode with TC_ACT_SHOT. A default action opcode configured through tc's
m_bpf can be: TC_ACT_RECLASSIFY, TC_ACT_PIPE, TC_ACT_SHOT, TC_ACT_UNSPEC,
TC_ACT_OK.
In cls_bpf, we have the possibility to overwrite the default class
associated with the classifier in case filter_res is _not_ 0xffffffff
(-1).
That allows us to fold multiple [e]BPF programs into a single one, where
they would otherwise need to be defined as a separate classifier with
its own classid, needlessly redoing parsing work, etc.
Similarly, we could do better in act_bpf: Since above TC_ACT* opcodes
are exported to UAPI anyway, we reuse them for return-code-to-tc-opcode
mapping, where we would allow above possibilities. Thus, like in cls_bpf,
a filter_res of 0xffffffff (-1) means that the configured _default_ action
is used. Any unkown return code from the BPF program would fail in
tcf_bpf() with TC_ACT_UNSPEC.
Should we one day want to make use of TC_ACT_STOLEN or TC_ACT_QUEUED,
which both have the same semantics, we have the option to either use
that as a default action (filter_res of 0xffffffff) or non-default BPF
return code.
All that will allow us to transparently use tcf_bpf() for both BPF
flavours.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Jiri Pirko <jiri@resnulli.us>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
If EPT was enabled, unrestricted_guest was allowed in L1 regardless of
L0. L1 triple faulted when running L2 guest that required emulation.
Another side effect was 'WARN_ON_ONCE(vmx->nested.nested_run_pending)'
in L0's dmesg:
WARNING: CPU: 0 PID: 0 at arch/x86/kvm/vmx.c:9190 nested_vmx_vmexit+0x96e/0xb00 [kvm_intel] ()
Prevent this scenario by masking SECONDARY_EXEC_UNRESTRICTED_GUEST when
the host doesn't have it enabled.
Fixes: 78051e3b7e ("KVM: nVMX: Disable unrestricted mode if ept=0")
Cc: stable@vger.kernel.org
Tested-By: Kashyap Chamarthy <kchamart@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
The gpiochip_lock_as_irq call can fail and return an error,
while the irq_startup is not expected to fail (returns an
unsigned int which is not checked by irq core code).
irq_request/release_resources functions have been created
to address this problem.
Move gpiochip_lock/unlock_as_irq calls into
irq_request/release_resources functions to prevent using a
gpio as an irq if the gpiochip_lock_as_irq call failed.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is a typo here so we deadlock.
Fixes: dd1f1f391d ('rtc: at91rm9200: rework wakeup and interrupt handling')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reported-by: David Dueck <davidcdueck@googlemail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We are keeping track of how many extents we need to reserve properly based on
the amount we want to write, but we were still incrementing outstanding_extents
if we wrote less than what we requested. This isn't quite right since we will
be limited to our max extent size. So instead lets do something horrible! Keep
track of how many outstanding_extents we reserved, and decrement each time we
allocate an extent. If we use our entire reserve make sure to jack up
outstanding_extents on the inode so the accounting works out properly. Thanks,
Reported-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Josef Bacik <jbacik@fb.com>
I introduced a regression wrt outstanding_extents accounting. These are tricky
areas that aren't easily covered by xfstests as we could change MAX_EXTENT_SIZE
at any time. So add sanity tests to cover the various conditions that are
tricky in order to make sure we don't introduce regressions in the future.
Thanks,
Signed-off-by: Josef Bacik <jbacik@fb.com>
Pull x86 fixes from Ingo Molnar:
"Misc fixes from all around the place:
- a KASLR related revert where we ran out of time to get a fix - this
represents a substantial portion of the diffstat,
- two FPU fixes,
- two x86 platform fixes: an ACPI reduced-hw fix and a NumaChip fix,
- an entry code fix,
- and a VDSO build fix"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
Revert "x86/mm/ASLR: Propagate base load address calculation"
x86/fpu: Drop_fpu() should not assume that tsk equals current
x86/fpu: Avoid math_state_restore() without used_math() in __restore_xstate_sig()
x86/apic/numachip: Fix sibling map with NumaChip
x86/platform, acpi: Bypass legacy PIC and PIT in ACPI hardware reduced mode
x86/asm/entry/32: Fix user_mode() misuses
x86/vdso: Fix the build on GCC5
If we fail during our sanity tests we could get NULL deref's because we unload
the module before the dummy extent buffers are free'd via RCU. So check for
this case and just free the things directly. Thanks,
Signed-off-by: Josef Bacik <jbacik@fb.com>
My fix
Btrfs: fix merge delalloc logic
only fixed half of the problems, it didn't fix the case where we have two large
extents on either side and then join them together with a new small extent. We
need to instead keep track of how many extents we have accounted for with each
side of the new extent, and then see how many extents we need for the new large
extent. If they match then we know we need to keep our reservation, otherwise
we need to drop our reservation. This shows up with a case like this
[BTRFS_MAX_EXTENT_SIZE+4K][4K HOLE][BTRFS_MAX_EXTENT_SIZE+4K]
Previously the logic would have said that the number extents required for the
new size (3) is larger than the number of extents required for the largest side
(2) therefore we need to keep our reservation. But this isn't the case, since
both sides require a reservation of 2 which leads to 4 for the whole range
currently reserved, but we only need 3, so we need to drop one of the
reservations. The same problem existed for splits, we'd think we only need 3
extents when creating the hole but in reality we need 4. Thanks,
Signed-off-by: Josef Bacik <jbacik@fb.com>
486b908 (HID: wacom: do not send pen events before touch is up/forced out)
introduces a kernel oops when plugging a tablet without touch.
wacom->shared is null for these devices so this leads to a null pointer
exception.
Change the condition to make it clear that what we need is wacom->shared
not NULL.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The commit breaks the legacy platforms, ie. these not using device-tree,
and setting up the interrupt resources with a flag to activate edge
detection. The issue was found on the zylonite platform.
The reason is that zylonite uses platform resources to pass the interrupt number
and the irq flags (here IORESOURCE_IRQ_HIGHEDGE). It expects the driver to
request the irq with these flags, which in turn setups the irq as high edge
triggered.
After the patch, this was supposed to be taken care of with :
irq_resflags = irqd_get_trigger_type(irq_get_irq_data(ndev->irq));
But irq_resflags is 0 for legacy platforms, while for example in
arch/arm/mach-pxa/zylonite.c, in struct resource smc91x_resources[] the
irq flag is specified. This breaks zylonite because the interrupt is not
setup as triggered, and hardware doesn't provide interrupts.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 2b0bb01b6e, the kernel returns -ENOBUFS when user tries to add
an existing tunnel with ioctl API:
$ ip -6 tunnel add ip6tnl1 mode ip6ip6 dev eth1
add tunnel "ip6tnl0" failed: No buffer space available
It's confusing, the right error is EEXIST.
This patch also change a bit the code returned:
- ENOBUFS -> ENOMEM
- ENOENT -> ENODEV
Fixes: 2b0bb01b6e ("ip6_tunnel: Return an error when adding an existing tunnel.")
CC: Steffen Klassert <steffen.klassert@secunet.com>
Reported-by: Pierre Cheynier <me@pierre-cheynier.net>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The argument 'flags' was missing in ndo_bridge_setlink().
ndo_bridge_dellink() was missing.
Fixes: 407af3299e ("bridge: Add netlink interface to configure vlans on bridge ports")
Fixes: add511b382 ("bridge: add flags argument to ndo_bridge_setlink and ndo_bridge_dellink")
CC: Vlad Yasevich <vyasevic@redhat.com>
CC: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The two main fixes here from Javier and Doug both fix issues seen on the
Exynos-based ARM Chromebooks with reference counting of GPIO regulators
over system suspend. The GPIO enable code didn't properly take account
of this cases (a full analysis is in Doug's commit log). This is fixed
by both fixing the reference counting directly and by making the resume
code skip enables it doesn't need to do. We could skip the change in
the resume code but it's a very simple change and adds extra robustness
against problems in other drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVCBjKAAoJECTWi3JdVIfQiA4H/2/zS+bEGIJs0yquAsmNT0as
v1XW+K8pw8klcCUbUpBgeqwBDmhiHHJtL5AWuC68KZHLRmg4+ryRdCyUgZ51AyJ4
4obGKxVrWpO0xM3BLeoeCc0ZSAAQzVuxplFSyFEbE14ULUKBqsVS8YKD2+FyrDRL
0RPAdNDak2Z7HD60W6234qqGfmEW0e1NAYTuZ7sCjE4dp8+S8OeauuwT489tuGt7
7N+BusHHnjWASW3tcitANTE8f3l3K4b5sUueolxi+ZghnrcxHcZn7LlKbVj0tpiF
yOCjc6jiLUL5UiCZ5q5IhamKPCTpTf/9LJlsjoSmj3Ze4PXn9/rEPW3wrIUyAh4=
=Dxlj
-----END PGP SIGNATURE-----
Merge tag 'regulator-fix-v4.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"The two main fixes here from Javier and Doug both fix issues seen on
the Exynos-based ARM Chromebooks with reference counting of GPIO
regulators over system suspend. The GPIO enable code didn't properly
take account of this case (a full analysis is in Doug's commit log).
This is fixed by both fixing the reference counting directly and by
making the resume code skip enables it doesn't need to do. We could
skip the change in the resume code but it's a very simple change and
adds extra robustness against problems in other drivers"
* tag 'regulator-fix-v4.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: tps65910: Add missing #include <linux/of.h>
regulator: core: Fix enable GPIO reference counting
regulator: Only enable disabled regulators on resume
Disable the pm_runtime of the device upon remove. This is
added to balance the pm_runtime_enable() invoked in the probe.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The current OMAP dmtimer probe does not check for the return
status of pm_runtime_get_sync() before initializing the timer
registers. Any timer with missing hwmod data would return a
failure here, and the access of registers without enabling the
clocks for the timer would trigger a l3_noc interrupt and a
kernel boot hang. Add proper checking so that the probe would
return a failure graciously without hanging the kernel boot.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
