The public Intel Xeon 5500 volume 2 datasheet describes, on page 53,
session 2.6.7 a register that can lock/unlock Memory Controller the
configuration register, called MC_CFG_CONTROL.
Adds support for it in the hope that software error injection would
work. With my tests with Xeon 35xx, there's still something missing.
With a program that does sequencial bit writes at dev 0.0, sometimes, it
produces error injection, after unblocking the MC_CFG_CONTROL (and,
sometimes, it just locks my testing machine).
I'll try later to discover by trial and error what's the register that
solves this issue on Xeon 35xx.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This driver is meant to support i7 core/i7core extreme desktop
processors and Xeon 35xx/55xx series with integrated memory controller.
It is likely that it can be expanded in the future to work with other
processor series based at the same Memory Controller design.
For now, it has just a few MCH status reads.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6: (36 commits)
jsm: fixing error if the driver fails to load
jsm: removing the uart structure and filename on error
tty: Add a new VT mode which is like VT_PROCESS but doesn't require a VT_RELDISP ioctl call
tty: Keep the default buffering to sub-page units
tty: Fix up char drivers request_room usage
tty: Fix the ldisc hangup race
serial: timberdale: Remove dependancies
nozomi: Tidy up the PCI table
nozomi: Fix mutex handling
nozomi: Add tty_port usage
sdio_uart: Use kfifo instead of the messy circ stuff
serial: bcm63xx_uart: allow more than one uart to be registered.
serial: bcm63xx_uart: don't use kfree() on non kmalloced area.
serial: bfin_5xx: pull in linux/io.h for ioremap prototypes
serial: bfin_5xx: kgdboc should accept gdb break only when it is active
serial: bfin_5xx: need to disable DMA TX interrupt too
serial: bfin_5xx: remove useless gpio handling with hard flow control
Char: synclink, remove unnecessary checks
tty: declare MODULE_FIRMWARE in various drivers
ip2: Add module parameter.
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6: (23 commits)
firewire: ohci: extend initialization log message
firewire: ohci: fix IR/IT context mask mixup
firewire: ohci: add module parameter to activate quirk fixes
firewire: ohci: use an ID table for quirks detection
firewire: ohci: reorder struct fw_ohci for better cache efficiency
firewire: ohci: remove unused dualbuffer IR code
firewire: core: combine a bit of repeated code
firewire: core: change type of a data buffer
firewire: cdev: increment ABI version number
firewire: cdev: add more flexible cycle timer ioctl
firewire: core: rename an internal function
firewire: core: fix an information leak
firewire: core: increase stack size of config ROM reader
firewire: core: don't fail device creation in case of too large config ROM blocks
firewire: core: fix "giving up on config rom" with Panasonic AG-DV2500
firewire: remove incomplete Bus_Time CSR support
firewire: get_cycle_timer optimization and cleanup
firewire: ohci: enable cycle timer fix on ALi and NEC controllers
firewire: ohci: work around cycle timer bugs on VIA controllers
firewire: make PCI device id constant
...
Add different model (with a different PCI ID) to support Korenix JetCard.
Signed-off-by: Kiros Yeh <kiros@korenix.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch is heavily based on an earlier patch found on the linux-serial
mailing list [1], written by Darius Augulis.
The previous incarnation of this patch only supported a 2x serial port
card. I have added support for my SYBA 6x serial port card, and tested on
x86.
[1]: http://marc.info/?l=linux-serial&m=124975806304760
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Cc: Darius Augulis <augulis.darius@gmail.com>
Cc: Greg KH <greg@kroah.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This code was no longer used since 2.6.33, "firewire: ohci: always use
packet-per-buffer mode for isochronous reception" commit 090699c0. If
anybody needs this code in the future for special purposes, it can be
brought back in. But it must not be re-enabled by default; drivers
(kernelspace or userspace drivers) should only get this mode if they
explicitly request it.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (151 commits)
powerpc: Fix usage of 64-bit instruction in 32-bit altivec code
MAINTAINERS: Add PowerPC patterns
powerpc/pseries: Track previous CPPR values to correctly EOI interrupts
powerpc/pseries: Correct pseries/dlpar.c build break without CONFIG_SMP
powerpc: Make "intspec" pointers in irq_host->xlate() const
powerpc/8xx: DTLB Miss cleanup
powerpc/8xx: Remove DIRTY pte handling in DTLB Error.
powerpc/8xx: Start using dcbX instructions in various copy routines
powerpc/8xx: Restore _PAGE_WRITETHRU
powerpc/8xx: Add missing Guarded setting in DTLB Error.
powerpc/8xx: Fixup DAR from buggy dcbX instructions.
powerpc/8xx: Tag DAR with 0x00f0 to catch buggy instructions.
powerpc/8xx: Update TLB asm so it behaves as linux mm expects.
powerpc/8xx: Invalidate non present TLBs
powerpc/pseries: Serialize cpu hotplug operations during deactivate Vs deallocate
pseries/pseries: Add code to online/offline CPUs of a DLPAR node
powerpc: stop_this_cpu: remove the cpu from the online map.
powerpc/pseries: Add kernel based CPU DLPAR handling
sysfs/cpu: Add probe/release files
powerpc/pseries: Kernel DLPAR Infrastructure
...
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (222 commits)
[SCSI] zfcp: Remove flag ZFCP_STATUS_FSFREQ_TMFUNCNOTSUPP
[SCSI] zfcp: Activate fc4s attributes for zfcp in FC transport class
[SCSI] zfcp: Block scsi_eh thread for rport state BLOCKED
[SCSI] zfcp: Update FSF error reporting
[SCSI] zfcp: Improve ELS ADISC handling
[SCSI] zfcp: Simplify handling of ct and els requests
[SCSI] zfcp: Remove ZFCP_DID_MASK
[SCSI] zfcp: Move WKA port to zfcp FC code
[SCSI] zfcp: Use common code definitions for FC CT structs
[SCSI] zfcp: Use common code definitions for FC ELS structs
[SCSI] zfcp: Update FCP protocol related code
[SCSI] zfcp: Dont fail SCSI commands when transitioning to blocked fc_rport
[SCSI] zfcp: Assign scheduled work to driver queue
[SCSI] zfcp: Remove STATUS_COMMON_REMOVE flag as it is not required anymore
[SCSI] zfcp: Implement module unloading
[SCSI] zfcp: Merge trace code for fsf requests in one function
[SCSI] zfcp: Access ports and units with container_of in sysfs code
[SCSI] zfcp: Remove suspend callback
[SCSI] zfcp: Remove global config_mutex
[SCSI] zfcp: Replace local reference counting with common kref
...
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: (54 commits)
Revert "pata_sis: Implement MWDMA for the UDMA 133 capable chips"
libata: Clarify ata_set_lba_range_entries function
libata: Report zeroed read after TRIM and max discard size
pata_hpt3x2n: fix overclocked MWDMA0 timing
pata_it8213: MWDMA0 is unsupported
[libata] MWDMA0 is unsupported on PIIX-like PATA controllers
pata_via: clear UDMA transfer mode bit for PIO and MWDMA
pata_sis: Power Management fix
pata_rz1000: Power Management fix
pata_radisys: fix UDMA handling
pata_ns87415: Power Management fix
pata_marvell: fix marvell_pre_reset() documentation
pata_legacy: add pointers to QDI65x0 documentation
pata_legacy: fix access to control register for QDI6580
pata_legacy: fix QDI6580DP support
pata_it8213: fix it8213_pre_reset() documentation
pata_it8213: fix wrong MWDMA timings being programmed
pata_it8213: fix PIO2 underclocking
pata_it8213: fix wrong PIO timings being programmed
pata_it8213: fix UDMA handling
...
This driver supports PMC-Sierra PCIe SAS/SATA 8x6G SPC 8001 chip based
host adapters.
Signed-off-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: Lindar Liu <lindar_liu@usish.com>
Signed-off-by: Tom Peng <tom_peng@usish.com>
Signed-off-by: Kevin Ao <aoqingyun@usish.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
We were never able to get docs for this out of Toshiba for years. Dave
Barnes produced a NetBSD driver however and from that we can fill in the
needed tables.
As we correct the PCI identifiers a bit also update the old ide generic driver
at the same time so it stays compiling.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This seems to be a different model (with a different PCI ID) than the
"Quatro" card that is also in the list.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The IBM Saturn serial card has only one port. Without that fixup,
the kernel thinks it has two, which confuses userland setup and
admin tools as well.
[akpm@linux-foundation.org: fix pci-ids.h layout]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Alan Cox <alan@linux.intel.com>
Cc: Michael Reed <mreed10@us.ibm.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Out of 10 PCI_IDs found in the PCMCIA subsystem, only two were not defined in
pci_ids.h. Move them and drop the duplicates. Successfully build-tested.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
This quirk will disable fast back to back transfer on the secondary bus
segment of the TI Bridge.
Signed-off-by: Gabe Black <gabe.black@ni.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'for-linus' of git://neil.brown.name/md: (97 commits)
md: raid-1/10: fix RW bits manipulation
md: remove unnecessary memset from multipath.
md: report device as congested when suspended
md: Improve name of threads created by md_register_thread
md: remove sparse warnings about lock context.
md: remove sparse waring "symbol xxx shadows an earlier one"
async_tx/raid6: add missing dma_unmap calls to the async fail case
ioat3: fix uninitialized var warnings
drivers/dma/ioat/dma_v2.c: fix warnings
raid6test: fix stack overflow
ioat2: clarify ring size limits
md/raid6: cleanup ops_run_compute6_2
md/raid6: eliminate BUG_ON with side effect
dca: module load should not be an error message
ioat: driver version 4.0
dca: registering requesters in multiple dca domains
async_tx: remove HIGHMEM64G restriction
dmaengine: sh: Add Support SuperH DMA Engine driver
dmaengine: Move all map_sg/unmap_sg for slave channel to its client
fsldma: Add DMA_SLAVE support
...
This is a new pata driver for ARTOP 867X 64bit 4-channel UDMA133 ATA ctrls.
Based on the Atp867 data sheet rev 1.2, Acard, and in part on early ide codes
from Eric Uhrhane <ericu@google.com>.
Signed-off-by: John(Jung-Ik) Lee <jilee@google.com>
Reviewed-by: Grant Grundler <grundler@google.com>
Reviewed-by: Gwendal Gringo <gwendal@google.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (75 commits)
PCI hotplug: clean up acpi_run_hpp()
PCI hotplug: acpiphp: use generic pci_configure_slot()
PCI hotplug: shpchp: use generic pci_configure_slot()
PCI hotplug: pciehp: use generic pci_configure_slot()
PCI hotplug: add pci_configure_slot()
PCI hotplug: clean up acpi_get_hp_params_from_firmware() interface
PCI hotplug: acpiphp: don't cache hotplug_params in acpiphp_bridge
PCI hotplug: acpiphp: remove superfluous _HPP/_HPX evaluation
PCI: Clear saved_state after the state has been restored
PCI PM: Return error codes from pci_pm_resume()
PCI: use dev_printk in quirk messages
PCI / PCIe portdrv: Fix pcie_portdrv_slot_reset()
PCI Hotplug: convert acpi_pci_detect_ejectable() to take an acpi_handle
PCI Hotplug: acpiphp: find bridges the easy way
PCI: pcie portdrv: remove unused variable
PCI / ACPI PM: Propagate wake-up enable for devices w/o ACPI support
ACPI PM: Replace wakeup.prepared with reference counter
PCI PM: Introduce device flag wakeup_prepared
PCI / ACPI PM: Rework some debug messages
PCI PM: Simplify PCI wake-up code
...
Fixed up conflict in arch/powerpc/kernel/pci_64.c due to OF device tree
scanning having been moved and merged for the 32- and 64-bit cases. The
'needs_freset' initialization added in 6e19314cc ("PCI/powerpc: support
PCIe fundamental reset") is now in arch/powerpc/kernel/pci_of_scan.c.
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (134 commits)
powerpc/nvram: Enable use Generic NVRAM driver for different size chips
powerpc/iseries: Fix oops reading from /proc/iSeries/mf/*/cmdline
powerpc/ps3: Workaround for flash memory I/O error
powerpc/booke: Don't set DABR on 64-bit BookE, use DAC1 instead
powerpc/perf_counters: Reduce stack usage of power_check_constraints
powerpc: Fix bug where perf_counters breaks oprofile
powerpc/85xx: Fix SMP compile error and allow NULL for smp_ops
powerpc/irq: Improve nanodoc
powerpc: Fix some late PowerMac G5 with PCIe ATI graphics
powerpc/fsl-booke: Use HW PTE format if CONFIG_PTE_64BIT
powerpc/book3e: Add missing page sizes
powerpc/pseries: Fix to handle slb resize across migration
powerpc/powermac: Thermal control turns system off too eagerly
powerpc/pci: Merge ppc32 and ppc64 versions of phb_scan()
powerpc/405ex: support cuImage via included dtb
powerpc/405ex: provide necessary fixup function to support cuImage
powerpc/40x: Add support for the ESTeem 195E (PPC405EP) SBC
powerpc/44x: Add Eiger AMCC (AppliedMicro) PPC460SX evaluation board support.
powerpc/44x: Update Arches defconfig
powerpc/44x: Update Arches dts
...
Fix up conflicts in drivers/char/agp/uninorth-agp.c
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1623 commits)
netxen: update copyright
netxen: fix tx timeout recovery
netxen: fix file firmware leak
netxen: improve pci memory access
netxen: change firmware write size
tg3: Fix return ring size breakage
netxen: build fix for INET=n
cdc-phonet: autoconfigure Phonet address
Phonet: back-end for autoconfigured addresses
Phonet: fix netlink address dump error handling
ipv6: Add IFA_F_DADFAILED flag
net: Add DEVTYPE support for Ethernet based devices
mv643xx_eth.c: remove unused txq_set_wrr()
ucc_geth: Fix hangs after switching from full to half duplex
ucc_geth: Rearrange some code to avoid forward declarations
phy/marvell: Make non-aneg speed/duplex forcing work for 88E1111 PHYs
drivers/net/phy: introduce missing kfree
drivers/net/wan: introduce missing kfree
net: force bridge module(s) to be GPL
Subject: [PATCH] appletalk: Fix skb leak when ipddp interface is not loaded
...
Fixed up trivial conflicts:
- arch/x86/include/asm/socket.h
converted to <asm-generic/socket.h> in the x86 tree. The generic
header has the same new #define's, so that works out fine.
- drivers/net/tun.c
fix conflict between 89f56d1e9 ("tun: reuse struct sock fields") that
switched over to using 'tun->socket.sk' instead of the redundantly
available (and thus removed) 'tun->sk', and 2b980dbd ("lsm: Add hooks
to the TUN driver") which added a new 'tun->sk' use.
Noted in 'next' by Stephen Rothwell.
IDs should generally only be added to pci_ids.h when they're shared
across several files in the tree. IDs that are just used by a single
driver should be defined in the driver instead.
Perhaps documenting this is a good idea to prevent things being moved there,
as it still seems to be happening judging from the git log.
(based on discussion w/gregkh and others).
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Jasper Forest introduces raid offload support via ioat3.2 support. When
raid offload is enabled two (out of 8 channels) will report raid5/raid6
offload capabilities. The remaining channels will only report ioat3.0
capabilities (memcpy).
Signed-off-by: Tom Picard <tom.s.picard@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
A misconfiguration by the firmware of the U4 PCIe bridge on PowerMac G5
with the U4 bridge (latest generations, may also affect the iMac G5
"iSight") is causing us to re-assign the PCI BARs of the video card,
which can get it out of sync with the firmware, thus breaking offb.
This works around it by fixing up the bridge configuration properly
at boot time. It also fixes a bug where the firmware provides us with
an incorrect set of accessible regions in the device-tree.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch adds a new device ID for those 5785 devices that will only
use 10/100 phys.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Synced with Realtek's 6.011.00 r8169 driver.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add PCI initialization code to take control of the xHCI host controller
away from the BIOS, halt, and reset the host controller. The xHCI spec
says that BIOSes must give up the host controller within 5 seconds.
Add some host controller glue functions to handle hardware initialization
and memory allocation for the host controller. The current xHCI
prototypes use PCI interrupts, but the xHCI spec requires MSI-X
interrupts. Add code to support MSI-X interrupts, but use the PCI
interrupts for now.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (103 commits)
powerpc: Fix bug in move of altivec code to vector.S
powerpc: Add support for swiotlb on 32-bit
powerpc/spufs: Remove unused error path
powerpc: Fix warning when printing a resource_size_t
powerpc/xmon: Remove unused variable in xmon.c
powerpc/pseries: Fix warnings when printing resource_size_t
powerpc: Shield code specific to 64-bit server processors
powerpc: Separate PACA fields for server CPUs
powerpc: Split exception handling out of head_64.S
powerpc: Introduce CONFIG_PPC_BOOK3S
powerpc: Move VMX and VSX asm code to vector.S
powerpc: Set init_bootmem_done on NUMA platforms as well
powerpc/mm: Fix a AB->BA deadlock scenario with nohash MMU context lock
powerpc/mm: Fix some SMP issues with MMU context handling
powerpc: Add PTRACE_SINGLEBLOCK support
fbdev: Add PLB support and cleanup DCR in xilinxfb driver.
powerpc/virtex: Add ml510 reference design device tree
powerpc/virtex: Add Xilinx ML510 reference design support
powerpc/virtex: refactor intc driver and add support for i8259 cascading
powerpc/virtex: Add support for Xilinx PCI host bridge
...
The code is divided in two parts. There is a virtual 'bus' driver
that handles PCI device and registers three new devices one per card
reader type. The other driver handles SD/MMC part of the reader.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (290 commits)
ALSA: pcm - Update document about xrun_debug proc file
ALSA: lx6464es - support standard alsa module parameters
ALSA: snd_usb_caiaq: set mixername
ALSA: hda - add quirk for STAC92xx (SigmaTel STAC9205)
ALSA: use card device as parent for jack input-devices
ALSA: sound/ps3: Correct existing and add missing annotations
ALSA: sound/ps3: Restructure driver source
ALSA: sound/ps3: Fix checkpatch issues
ASoC: Fix lm4857 control
ALSA: ctxfi - Clear PCM resources at hw_params and hw_free
ALSA: ctxfi - Check the presence of SRC instance in PCM pointer callbacks
ALSA: ctxfi - Add missing start check in atc_pcm_playback_start()
ALSA: ctxfi - Add use_system_timer module option
ALSA: usb - Add boot quirk for C-Media 6206 USB Audio
ALSA: ctxfi - Fix wrong model id for UAA
ALSA: ctxfi - Clean up probe routines
ALSA: hda - Fix the previous tagra-8ch patch
ALSA: hda - Add 7.1 support for MSI GX620
ALSA: pcm - A helper function to compose PCM stream name for debug prints
ALSA: emu10k1 - Fix minimum periods for efx playback
...
This adds support for the following serial controller chip:
Oxford Semiconductor OXCB950 for PCI Cardbus interface
http://www.transdimension.com/products/serial/OXCB950.html
on this card:
ExSys EX-1370 1 port high-speed serial card for ExpressCard/34 slot
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mauro Carvalho Chehab