commit 7f638c1cb0 upstream.
smbus functions return -ve on error, 0 on success. However,
__i2c_transfer() have a different return signature - -ve on error, or
number of buffers transferred (which may be zero or greater.)
The upshot of this is that the sense of the test is reversed when using
the mux on a bus supporting the master_xfer method: we cache the value
and never retry if we fail to transfer any buffers, but if we succeed,
we clear the cached value.
Fix this by making pca954x_reg_write() return a negative error code for
all failure cases.
Fixes: 463e8f845c ("i2c: mux: pca954x: retry updating the mux selection on failure")
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Deselect functionality can be ignored for device-trees with
"i2c-mux-idle-disconnect" entries if no platform_data is available.
By enabling the deselect functionality outside the platform_data
block the logic works as it did in previous kernels.
Fixes: 7fcac98071 ("i2c: i2c-mux-pca954x: convert to use an explicit i2c mux core")
Cc: <stable@vger.kernel.org> # v4.7+
Signed-off-by: Alex Hemme <ahemme@cisco.com>
Signed-off-by: Ziyang Wu <ziywu@cisco.com>
[touched up a few minor issues /peda]
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We get the following build error from UM Linux after adding
an entry to drivers/iio/gyro/Kconfig that issues "select I2C_MUX":
ERROR: "devm_ioremap_resource"
[drivers/i2c/muxes/i2c-mux-reg.ko] undefined!
ERROR: "of_address_to_resource"
[drivers/i2c/muxes/i2c-mux-reg.ko] undefined!
It appears that the I2C mux core code depends on HAS_IOMEM
for historical reasons, while CONFIG_I2C_MUX_REG does *not*
have a direct dependency on HAS_IOMEM.
This creates a situation where a allyesconfig or allmodconfig
for UM Linux will select I2C_MUX, and will implicitly enable
I2C_MUX_REG as well, and the compilation will fail for the
register driver.
Fix this up by making I2C_MUX_REG depend on HAS_IOMEM and
removing the dependency from I2C_MUX.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Reported-by: Jonathan Cameron <jic23@jic23.retrosnub.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Some drivers like i2c-gpio do not have dedicated pinctrl states. They
broke when error checking for pinctrl was added. Detect them now, and in
their case, simply skip over pinctrl configuration.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull i2c updates from Wolfram Sang:
"Here is the 4.9 pull request from I2C including:
- centralized error messages when registering to the core
- improved lockdep annotations to prevent false positives
- DT support for muxes, gates, and arbitrators
- bus speeds can now be obtained from ACPI
- i2c-octeon got refactored and now supports ThunderX SoCs, too
- i2c-tegra and i2c-designware got a bigger bunch of updates
- a couple of standard driver fixes and improvements"
* 'i2c/for-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (71 commits)
i2c: axxia: disable clks in case of failure in probe
i2c: octeon: thunderx: Limit register access retries
i2c: uniphier-f: fix misdetection of incomplete STOP condition
gpio: pca953x: variable 'id' was used twice
i2c: i801: Add support for Kaby Lake PCH-H
gpio: pca953x: fix an incorrect lockdep warning
i2c: add a warning to i2c_adapter_depth()
lockdep: make MAX_LOCKDEP_SUBCLASSES unconditionally visible
i2c: export i2c_adapter_depth()
i2c: rk3x: Fix variable 'min_total_ns' unused warning
i2c: rk3x: Fix sparse warning
i2c / ACPI: Do not touch an I2C device if it belongs to another adapter
i2c: octeon: Fix high-level controller status check
i2c: octeon: Avoid sending STOP during recovery
i2c: octeon: Fix set SCL recovery function
i2c: rcar: add support for r8a7796 (R-Car M3-W)
i2c: imx: make bus recovery through pinctrl optional
i2c: meson: add gxbb compatible string
i2c: uniphier-f: set the adapter to master mode when probing
i2c: uniphier-f: avoid WARN_ON() of clk_disable() in failure path
...
The cached value of the last selected channel prevents retries on the
next call, even on failure to update the selected channel. Fix that.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
We can't use a static property for all the changesets, so we now create
dynamic ones for each changeset.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Fixes: 50a5ba8769 ("i2c: mux: demux-pinctrl: add driver")
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
No longer rely on the implicit matching with the i2c device name, use
an explicit compatible string instead.
Keep a direct pointer to the chip description instead of an index into
the chip description array.
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Peter Rosin <peda@axentia.se>
No longer rely on the implicit matching with the i2c device name, use
an explicit compatible string instead.
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Peter Rosin <peda@axentia.se>
The i2c mux core can then take appropriate action depending on if it is
used for an actual i2c mux, for a gate or for an arbitrator (the last
is the case for these drivers). This adds support for the new clearer
and more compact devicetree bindings that was added recently.
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Peter Rosin <peda@axentia.se>
Make sure the index to the active channel is invalidated when switching
fails.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We also need to revert the dynamic OF change, so we get a consistent
state again. Otherwise, we might have two devices enabled e.g. after
pinctrl setup fails.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
of_address_to_resource return 0 on successful call but
devm_ioremap_resource is called only if it returns non-zero value
Signed-off-by: Lukasz Gemborowski <lukasz.gemborowski@nokia.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
of_match_table was not filled which prevents device to be
instantiated from device tree node.
Signed-off-by: Lukasz Gemborowski <lukasz.gemborowski@nokia.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
With a i2c topology like the following
GPIO ---| ------ BAT1
| v /
I2C -----+----------+---- MUX
| \
EEPROM ------ BAT2
there is a locking problem with the GPIO controller since it is a client
on the same i2c bus that it muxes. Transfers to the mux clients (e.g. BAT1)
will lock the whole i2c bus prior to attempting to switch the mux to the
correct i2c segment. In the above case, the GPIO device is an I/O expander
with an i2c interface, and since the GPIO subsystem knows nothing (and
rightfully so) about the lockless needs of the i2c mux code, this results
in a deadlock when the GPIO driver issues i2c transfers to modify the
mux.
So, observing that while it is needed to have the i2c bus locked during the
actual MUX update in order to avoid random garbage on the slave side, it
is not strictly a must to have it locked over the whole sequence of a full
select-transfer-deselect mux client operation. The mux itself needs to be
locked, so transfers to clients behind the mux are serialized, and the mux
needs to be stable during all i2c traffic (otherwise individual mux slave
segments might see garbage, or worse).
Introduce this new locking concept as "mux-locked" muxes, and call the
pre-existing mux locking scheme "parent-locked".
Modify the i2c mux locking so that muxes that are "mux-locked" locks only
the muxes on the parent adapter instead of the whole i2c bus when there is
a transfer to the slave side of the mux. This lock serializes transfers to
the slave side of the muxes on the parent adapter.
Add code to i2c-mux-gpio and i2c-mux-pinctrl that checks if all involved
gpio/pinctrl devices have a parent that is an i2c adapter in the same
adapter tree that is muxed, and request a "mux-locked mux" if that is the
case.
Modify the select-transfer-deselect code for "mux-locked" muxes so
that each of the select-transfer-deselect ops locks the mux parent
adapter individually.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Allocate an explicit i2c mux core to handle parent and child adapters
etc. Update the select/deselect ops to be in terms of the i2c mux core
instead of the child adapter.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Allocate an explicit i2c mux core to handle parent and child adapters
etc. Update the select/deselect ops to be in terms of the i2c mux core
instead of the child adapter.
Add a mask to handle the case where not all child adapters should
cause a mux deselect to happen, now that there is a common deselect op
for all child adapters.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Allocate an explicit i2c mux core to handle parent and child adapters
etc. Update the select/deselect ops to be in terms of the i2c mux core
instead of the child adapter.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Allocate an explicit i2c mux core to handle parent and child adapters
etc. Update the select/deselect ops to be in terms of the i2c mux core
instead of the child adapter.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Allocate an explicit i2c mux core to handle parent and child adapters
etc. Update the select/deselect ops to be in terms of the i2c mux core
instead of the child adapter.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Allocate an explicit i2c mux core to handle parent and child adapters
etc. Update the select/deselect ops to be in terms of the i2c mux core
instead of the child adapter.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
sysfs attributes should use the same format for reads and writes,
rather than pretty-printing on read.
* Make the "cur_master" attribute read back as just the name of the
master
* Expose the list of all masters as a read-only "available_masters"
attribute, using space separators as in similar attributes of other
devices
Also, spell out "cur_master" in full as "current_master".
Fixes: 50a5ba8769 ("i2c: mux: demux-pinctrl: add driver")
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This driver allows an I2C bus to switch between multiple masters. This
is not hot-switching because connected I2C slaves will be
re-instantiated. It is meant to select the best I2C core at runtime once
the task is known. Example: Prefer i2c-gpio over another I2C core
because of HW errata affecting your use case.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Reading the register (if allowed) after writing is to ensure writing
is completed on a posted bus. The endianness of reading doesn't matter.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
With CONFIG_OF=n, the following warnings occur when compiling
drivers/i2c/muxes/i2c-mux-reg.c:
CC drivers/i2c/muxes/i2c-mux-reg.o
drivers/i2c/muxes/i2c-mux-reg.c:170:13: warning: ‘struct gpiomux’ declared inside parameter list [enabled by default]
struct platform_device *pdev)
^
drivers/i2c/muxes/i2c-mux-reg.c:170:13: warning: its scope
is only this definition or declaration, which is probably not what you want [enabled by default]
drivers/i2c/muxes/i2c-mux-reg.c: In function ‘i2c_mux_reg_probe’:
drivers/i2c/muxes/i2c-mux-reg.c:201:3: warning: passing argument 1 of ‘i2c_mux_reg_probe_dt’ from incompatible pointer type [enabled by default]
ret = i2c_mux_reg_probe_dt(mux, pdev);
^
Signed-off-by: Mike Rapoport <mike.rapoport@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Checking was done at three different locations, just do it once and
properly at probing time.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Tested-by: York Sun <yorksun@freescale.com>
Every call of of_parse_phandle() increments user count of found device
node, if OF_DYNAMIC is enabled.
The change fixes all similar addressed cases in drivers/i2c.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Based on i2c-mux-gpio driver, similarly the register-based mux
switch from one bus to another by setting a single register.
The register can be on PCIe bus, local bus, or any memory-mapped
address. The endianness of such register can be specified in device
tree if used, or in platform data.
Signed-off-by: York Sun <yorksun@freescale.com>
Acked-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This change is needed to properly lock I2C parent bus driver.
Prior to this change i2c_put_adapter() is misused, which may lead
to an overflow over zero of I2C bus driver user counter.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
pca9541 and pca954x are calling master_xfer() of the parent adapter directly
thus bypassing the quirks checks of the adapter. Use __i2c_transfer() instead.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Tested-by: Łukasz Gemborowski <lukasz.gemborowski@nokia.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Fixes: b7f6258402 ("i2c: add quirk checks to core")
The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.
Relax the dependency on GPIOLIB if COMPILE_TEST is enabled, where
appropriate.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Probe deferral is not an error case. It happens only when
the necessary dependencies are not there yet.
The driver core is already printing a message when a driver
requests probe deferral, so this can be traced in the logs
without these error prints.
This patch removes the error messages for these deferral cases.
Signed-off-by: Ionut Nicu <ioan.nicu.ext@nokia.com>
Acked-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Acked-by: Peter Korsgaard <peter.korsgaard@barco.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Since 39b2bbe3d7 (gpio: add flags argument to gpiod_get*() functions)
which appeared in v3.17-rc1, the gpiod_get* functions take an additional
parameter that allows to specify direction and initial value for
outputs.
Also there is an *_optional variant that serves well here. The sematics
is slightly changed here by using it. Now if a reset gpio is specified
and getting hold on it fails, pca954x_probe fails, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add i2c-mux-idle-disconnect device tree property to PCA954x mux driver. The new
property forces the multiplexer to disconnect child buses in idle state. This is
used, for example, when there are several multiplexers on the same bus and the
devices on the underlying buses might have same I2C addresses.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nsn.com>
[wsa: added a newline]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull i2c updates from Wolfram Sang:
"Highlights:
- class based instantiation finally dropped for most embedded drivers
bringing boot up performance gains
- removed two drivers (one outdated, one a duplicate)
- ACPI has now operation region support (thanks to Lan Tianyu)
- the i2c-stub driver got overhauled and gained new features to
become more useful when writing i2c client drivers (thanks to
Guenter Roeck and Jean Delvare)
The rest is driver bugfixes, added bindings/ids, cleanups..."
* 'i2c/for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (43 commits)
i2c: mpc: delete unneeded test before of_node_put
i2c: rk3x: fix interrupt handling issue
i2c: imx: Fix format warning for dev_dbg
i2c: qup: disable clks and return instead of just returning error
i2c: exynos5: always enable HSI2C
i2c: designware: add new bindings
i2c: gpio: Drop dead code in i2c_gpio_remove
i2c: pca954x: put the mux to disconnected state after resume
i2c: st: Update i2c timings
drivers/i2c/busses: use correct type for dma_map/unmap
i2c: i2c-st: Use %pa to print 'resource_size_t' type
i2c: s3c2410: resume the I2C controller earlier
i2c: stub: Avoid an array overrun on I2C block transfers
i2c: i801: Add device ID for Intel Wildcat Point PCH
i2c: i801: Fix the alignment of the device table
i2c: stub: Add support for banked register ranges
i2c: stub: Remember the number of emulated chips
i2c: stub: Add support for SMBus block commands
i2c: efm32: correct namespacing of location property
i2c: exynos5: remove extra line and fix an assignment
...
pca954x may be power lost during suspend, so after resume we also suffer
the issue fixed by commit cd823db8b1,
"pca954x power-on default is channel 0 connected. If multiple pca954x
muxes are connected to the same physical I2C bus, the parent bus will
see channel 0 devices behind both muxes by default."
What's more, when resume bootloader may also operate the mux, so the
the channel connected after that may not be the one driver thought.
We fix this problem by putting the mux to disconnected state and
clearing last_chan in the resume hook.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This driver causes the following randconfig build error:
drivers/i2c/muxes/i2c-mux-pca954x.c: In function ‘pca954x_probe’:
drivers/i2c/muxes/i2c-mux-pca954x.c:204:2: error: implicit declaration
of function ‘devm_gpiod_get’ [-Werror=implicit-function-declaration]
gpio = devm_gpiod_get(&client->dev, "reset");
^
drivers/i2c/muxes/i2c-mux-pca954x.c:204:7: warning: assignment makes
pointer from integer without a cast [enabled by default]
gpio = devm_gpiod_get(&client->dev, "reset");
^
drivers/i2c/muxes/i2c-mux-pca954x.c:206:3: error: implicit declaration
of function ‘gpiod_direction_output’
[-Werror=implicit-function-declaration]
gpiod_direction_output(gpio, 0);
^
cc1: some warnings being treated as errors
make[3]: *** [drivers/i2c/muxes/i2c-mux-pca954x.o] Error 1
This is because it is getting compiled without gpiolib, so
introduce an explicit dependency.
Reported-by: Jim Davis <jim.epost@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The pca954x driver recently switched to the GPIO descriptor API without
including the correct <linux/gpio/consumer.h> header. This breaks
compilation without CONFIG_GPIOLIB.
drivers/i2c/muxes/i2c-mux-pca954x.c: In function ‘pca954x_probe’:
drivers/i2c/muxes/i2c-mux-pca954x.c:204:2: error: implicit declaration
of function ‘devm_gpiod_get’ [-Werror=implicit-function-declaration]
gpio = devm_gpiod_get(&client->dev, "reset");
^
drivers/i2c/muxes/i2c-mux-pca954x.c:204:7: warning: assignment makes
pointer from integer without a cast [enabled by default]
gpio = devm_gpiod_get(&client->dev, "reset");
^
drivers/i2c/muxes/i2c-mux-pca954x.c:206:3: error: implicit declaration
of function ‘gpiod_direction_output’
[-Werror=implicit-function-declaration]
gpiod_direction_output(gpio, 0);
^
cc1: some warnings being treated as errors
make[3]: *** [drivers/i2c/muxes/i2c-mux-pca954x.o] Error 1
Fix it by including the right header.
Reported-by: Jim Davis <jim.epost@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The ID-based GPIO API pushes handling of GPIO polarity to drivers.
Simplify the driver by switching to the descriptor-based GPIO API.
This also fixes a mismatch between the pca954x DT bindings that document
a "reset-gpios" property and the driver that requests a "reset-gpio"
property.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull more i2c updates from Wolfram Sang:
"Mostly bugfixes, small but wanted cleanups, and Paul's init.h removal
applied"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: rcar: fix NACK error code
i2c: update i2c_algorithm documentation
i2c: rcar: use devm_clk_get to ensure clock is properly ref-counted
i2c: rcar: do not print error if device nacks transfer
i2c: rely on driver core when sanitizing devices
i2c: delete non-required instances of include <linux/init.h>
i2c: acorn: is tristate and should use module.h
i2c: piix4: Standardize log messages
i2c: piix4: Use different message for AMD Auxiliary SMBus Controller
i2c: piix4: Add support for AMD ML and CZ SMBus changes
Pull hwmon updates from Jean Delvare:
"This include it87 driver improvements, and a tree-wide change of my
e-mail address"
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
Update Jean Delvare's e-mail address
hwmon: (it87) Print proper names for the IT8771E and IT8772E
hwmon: (it87) Add support for the ITE IT8603E
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If a reset GPIO support is specified, request the GPIO and get the chip
out of reset at probe time.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This simplifies error and removal paths.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull i2c changes from Wolfram Sang:
- new drivers for exynos5, bcm kona, and st micro
- bigger overhauls for drivers mxs and rcar
- typical driver bugfixes, cleanups, improvements
- got rid of the superfluous 'driver' member in i2c_client struct This
touches a few drivers in other subsystems. All acked.
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (38 commits)
i2c: bcm-kona: fix error return code in bcm_kona_i2c_probe()
i2c: i2c-eg20t: do not print error message in syslog if no ACK received
i2c: bcm-kona: Introduce Broadcom I2C Driver
i2c: cbus-gpio: Fix device tree binding
i2c: wmt: add missing clk_disable_unprepare() on error
i2c: designware: add new ACPI IDs
i2c: i801: Add Device IDs for Intel Wildcat Point-LP PCH
i2c: exynos5: Remove incorrect clk_disable_unprepare
i2c: i2c-st: Add ST I2C controller
i2c: exynos5: add High Speed I2C controller driver
i2c: rcar: fixup rcar type naming
i2c: scmi: remove some bogus NULL checks
i2c: sh_mobile & rcar: Enable the driver on all ARM platforms
i2c: sh_mobile: Convert to clk_prepare/unprepare
i2c: mux: gpio: use reg value for i2c_add_mux_adapter
i2c: mux: gpio: use gpio_set_value_cansleep()
i2c: Include linux/of.h header
i2c: mxs: Fix PIO mode on i.MX23
i2c: mxs: Rework the PIO mode operation
i2c: mxs: distinguish i.MX23 and i.MX28 based I2C controller
...
