the eg20t driver call request_irq() function before the pch_base_address,
base address of i2c controller's register, is assigned an effective value.
there is one possible scenario that an interrupt which isn't inside eg20t
arrives immediately after request_irq() is executed when i2c controller
shares an interrupt number with others. since the interrupt handler
pch_i2c_handler() has already active as shared action, it will be called
and read its own register to determine if this interrupt is from itself.
At that moment, since base address of i2c registers is not remapped
in kernel space yet,so the INT handler will access an illegal address
and then a error occurs.
Signed-off-by: Yadi.hu <yadi.hu@windriver.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Since commit 1c4b6c3bcf ("i2c: imx: implement bus recovery") the
driver starts to use gpio/pinctrl to support optional bus recovery
feature. But pinctrl is not always usable. There are platforms such
as ls1021a and ls1043a that don't support pinctrl, and it could just
be broken due to old/broken device tree. The patch makes it really
optional that the probe function won't bailout on pinctrl problems
instead it just disables bus recovery and prints out notification when
there is problem with pinctrl. Since pinctrl is only used by bus
recovery in this driver, move pinctrl initialization into bus recovery
init function to prevent confusion.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Depending on a number of factors including:
- Which exact Rockchip SoC we're working with
- How deep we suspend
- Which i2c port we're on
We might lose the state of the i2c registers at suspend time.
Specifically we've found that on rk3399 the i2c ports that are not in
the PMU power domain lose their state with the current suspend depth
configured by ARM Tursted Firmware.
Note that there are very few actual i2c registers that aren't configured
per transfer anyway so all we actually need to re-configure are the
clock config registers. We'll just add a call to rk3x_i2c_adapt_div()
at resume time and be done with it.
NOTE: On rk3399 on ports whose power was lost, I put printouts in at
resume time. I saw things like:
before: con=0x00010300, div=0x00060006
after: con=0x00010200, div=0x00180025
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: David Wu <david.wu@rock-chips.com>
Tested-by: David Wu <david.wu@rock-chips.com>
[wsa: removed duplicate const]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Currently, the adapter is set to the master mode at the first use.
Since then, it is kept in the slave mode, so unexpected glitch
signals on the I2C lines may cause the adapter into insane state.
Setting it to the master mode along with initialization solves the
problem.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reported-by: Akio Noda <noda.akio@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If clk_prepare_enable() fails, clk_disable_unprepare() is called in
the failure path, where the enable_count is still zero, so it hits
WARN_ON(core->enable_count == 0) in the clk_core_disable().
To fix this, make the clock setting more linear in the probe function
so that it can exploit "goto err" in case of error.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If clk_prepare_enable() fails, clk_disable_unprepare() is called in
the failure path, where the enable_count is still zero, so it hits
WARN_ON(core->enable_count == 0) in the clk_core_disable().
To fix this, make the clock setting more linear in the probe function
so that it can exploit "goto err" in case of error.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fix the following warnings reported by coccinelle for the Tegra I2C
driver.
drivers/i2c/busses/i2c-tegra.c:513:2-23: WARNING: Assignment of bool to 0/1
drivers/i2c/busses/i2c-tegra.c:539:3-24: WARNING: Assignment of bool to 0/1
Reported-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
To summarize the issue observed in error cases:
SW Flow: For i2c message transfer, packet header and data payload is
posted and then required error/packet completion interrupts are enabled
later.
HW flow: HW process the packet just after packet header is posted, if
ARB lost/NACK error occurs (SW will not handle immediately when error
happens as error interrupts are not enabled at this point). HW assumes
error is acknowledged and clears current data in FIFO, But SW here posts
the remaining data payload which still stays in FIFO as stale data
(data without packet header).
Now once the interrupts are enabled, SW handles ARB lost/NACK error by
clearing the ARB lost/NACK interrupt. Now HW assumes that SW attended
the error and will parse/process stale data (data without packet header)
present in FIFO which causes invalid NACK errors.
Fix: Enable the error interrupts before posting the packet into FIFO
which make sure HW to not clear the fifo. Also disable the packet mode
before acknowledging errors (ARB lost/NACK error) to not process any
stale data. As error interrupts are enabled before posting the packet
header use spinlock to avoid preempting.
Signed-off-by: Shardar Shariff Md <smohammed@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use readl_poll_timeout_atomic() function as *wait_for_config_load()
function can be called from interrupt context.
Signed-off-by: Shardar Shariff Md <smohammed@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Define separate function for configuration load register handling
to make it use by different functions later.
Signed-off-by: Shardar Shariff Md <smohammed@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
During i2c controller initialization, when fifo flush fails return error
instead of returning the error during exit.
Signed-off-by: Shardar Shariff Md <smohammed@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
After CONFIG_LOAD register is programmed instead of explicitly waiting
for timeout, use readl_poll_timeout() to check for register value to get
updated or wait till timeout.
Signed-off-by: Shardar Shariff Md <smohammed@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
"i2c-sh_mobile" is used on sh7343, sh7366, sh7722, sh7723, and sh7724
only. As all of the above select ARCH_SHMOBILE, restrict its driver
dependencies from SUPERH to ARCH_SHMOBILE.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There are several ways to set the SDA hold time for i2c controller,
including: Device Tree, built-in device properties and ACPI. However,
if the SDA hold time is not specified by above method, we should
read the value, where it is preset by firmware, and save it to
sda_hold_time. This is needed because when i2c controller enters
runtime suspend, the DW_IC_SDA_HOLD value will be reset to chipset
default value. And during runtime resume, i2c_dw_init will be called
to reconfigure i2c controller. If sda_hold_time is zero, the chipset
default hold time will be used, that will be too short for some
platforms. Therefore, to have a better tolerance, the DW_IC_SDA_HOLD
value should be kept by sda_hold_time.
Signed-off-by: Zhuo-hao Lee <zhuo-hao.lee@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We can't use a static property for all the changesets, so we now create
dynamic ones for each changeset.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Fixes: 50a5ba8769 ("i2c: mux: demux-pinctrl: add driver")
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
It's better to have strings in the code like they appeared in the output.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This makes it trivial to constify them, so do that.
Signed-off-by: Peter Rosin <peda@axentia.se>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
On Tegra124/132 the pins for I2C6 are shared with the Display Port AUX
(DPAUX) channel and on Tegra210 the pins for I2C4 and I2C6 are shared
with DPAUX1 and DPAUX0, respectively. The multiplexing of the pins is
handled by a register in the DPAUX and so the Tegra DPAUX driver has
been updated to register a pinctrl device for managing these pins.
The pins for these particular I2C devices are bound to the I2C device
prior to probing. However, these I2C devices are in a different power
partition to the DPAUX devices that own the pins. Hence, it is desirable
to place the pins in the 'idle' state and allow the DPAUX power
partition to switch off, when these I2C devices is not in use.
Therefore, add calls to place the I2C pins in the 'default' and 'idle'
states when the I2C device is runtime resumed and suspended,
respectively.
Please note that the pinctrl functions that set the state of the pins
check to see if the devices has pins associated and will return zero
if they do not. Therefore, it is safe to call these pinctrl functions
even for I2C devices that do not have any pins associated.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Update the Tegra I2C driver to use runtime PM and move the code in the
tegra_i2c_clock_enable/disable() functions to the PM runtime resume and
suspend callbacks, respectively.
Note that given that CONFIG_PM is not mandatory for Tegra, if CONFIG_PM
is not enabled and so runtime PM is not enabled, ensure that the I2C
clocks are turned on during probe and kept on by calling the resume
callback directly.
In the function tegra_i2c_init(), the variable 'err' does not need to be
initialised to zero in tegra_i2c_init() because it is initialised when
pm_runtime_get_sync() is called. Furthermore, to ensure we only return 0
from tegra_i2c_init(), it is necessary to re-initialise 'err' to 0 after
a successful call to pm_runtime_get_sync() because it can return a
positive value on success. However, alternatively re-initialise 'err' by
using the return value of the function tegra_i2c_flush_fifos() because
it can only be 0 or -ETIMEDOUT.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The I2C adapter is unlocked regardless of whether the tegra_i2c_init()
called during the resume is successful or not. However, if the
tegra_i2c_init() is not successful, then ->is_suspended is not set to
false. Simplify the resume code by only setting ->is_suspended to false
if tegra_i2c_init() is successful and return the error code from
tegra_i2c_init().
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
All Tegra I2C devices have the name "Tegra I2C adapter" which is not
very useful when viewing the I2C adapter names via the sysfs. Therefore,
use the device name, which is unique for each I2C device, instead.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Tegra has only supported device-tree for platform/board configuration
for quite some time now and so simplify the Tegra I2C driver by dropping
code for non device-tree platforms/boards.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add missing new line characters for the various error messages.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Checkpatch warns about missing blank lines after declarations in the
Tegra I2C driver and so fix these.
Note that the initialisation of 'val' to zero in tegra_dvc_init() is
unnecessary and so remove this.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Checkpatch warns about spacing around the '<<' operator in the Tegra I2C
driver and so fix these by converting the bit definitions that are using
this operator to use the BIT macro.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Checkpatch warns about some lines over 80 characters in the Tegra I2C
driver and so fix these.
While we are at it, prefix the second instance of "STOP condition" in
the comment with a "the".
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Disabling the adapter after each transfer adds additional delays
for each I2C transfer. Even if we don't wait for it to be disabled
anymore, on next transfer we will need to if we have several transfers
in a row.
Now during the transfer init we check if IC_TAR can be changed
dynamically, the status register for no activity and TX buffer being
empty. In this case we don't need to disable it
When a transfer fails the adapter will still be disabled - this is a
conservative approach. When transfers succeed, the adapter is left
enabled and it's configured so to disable interrupts.
Alternating register reads on 2 slaves:
perf stat -r4 chrt -f 10 ./i2c-test /dev/i2c-1 25000 0x40 0x6 0x1e 0x00
Before:
8.638705161 seconds time elapsed ( +- 5.90% )
After:
7.516821591 seconds time elapsed ( +- 0.11% )
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Christian Ruppert <christian.ruppert@alitech.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This adapter can be synthesized with dynamic tar update enabled or disabled.
When enabled it is not necessary to disable the adapter to change the slave
address in some situations, which saves some time per transaction.
There is no direct register to know if this feature is enabled but we can do it
indirectly by writing to the 10BIT_ADDR field in IC_CON: this field is
read only when dynamic tar update is enabled.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Christian Ruppert <christian.ruppert@alitech.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
These are used in 2 places and will be needed in more.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Christian Ruppert <christian.ruppert@alitech.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If we aren't going to continue using the controller we can just disable
it instead of waiting for it to complete. The biggest improvement here
is when a I2C transaction is completed and it doesn't block until
the adapter is disabled. When a new transfer is needed we will disable
and wait for its completion.
This way the adapter will continue changing its state in parallel to the
execution of the thread that requested the I2C transaction saving most
of the time 25~250 usec per I2C transaction.
A simple program doing a register read (1 byte write, 1 byte read)
alternating on 2 different slaves repeated 25k times for each and
measurements taken 4 times we get:
perf stat -r4 chrt -f 10 ./i2c-test /dev/i2c-1 25000 0x40 0x6 0x1e 0x00
Before:
30.879317977 seconds time elapsed ( +- 14.83% )
After:
8.638705161 seconds time elapsed ( +- 5.90% )
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Christian Ruppert <christian.ruppert@alitech.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fast mode is the default speed of i2c-designware which can be overridden
by platform data or by "clock-frequency" device property. Even though
the ACPI 5.1 can pass device properties via _DSD method, shipping systems
define the connection speed between I2C host and each slave in their
I2cSerialBus resources. Which means speed is not defined per bus but per
slave.
As there is now support in i2c-core to find the bus speed from ACPI use
that to set up the bus speed prior registering the I2C adapter.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
ACPI 5 specification doesn't have property for the I2C bus speed but
I2cSerialBus resource descriptor which define each controller-slave
connection define the maximum speed supported by that connection.
Thus finding the maximum safe speed for the bus is to walk through all
I2cSerialBus resources that are associated to I2C controller and use the
speed of slowest connection.
Add function i2c_acpi_find_bus_speed() to the i2c-core that adapter
drivers can call prior registering itself to core.
This implies two-step walk through the I2cSerialBus resources: call to
i2c_acpi_find_bus_speed() does the first scan and finds the safe bus
speed that adapter drivers can set up. Adapter driver registration does
the second scan when i2c-core creates the I2C slaves by calling the
i2c_acpi_register_devices(). In that way the bus speed is set in case
slave device probe gets called during registration and does communication.
Previous version commit 55d38d060e ("i2c: core: Add function for finding
the bus speed from ACPI") got reverted due merge conflicts from
commit 525e6fabea ("i2c / ACPI: add support for ACPI reconfigure
notifications").
This version is a bit bigger than previous version but is still sharing
the lowest and complicated part of I2cSerialBus lookup routines with the
existing code.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
I2C ACPI enumeration was originally implemented in another module under
drivers/acpi/ but was later moved into i2c-core with added support for
I2C ACPI operation region.
Rename these acpi_i2c_ prefixed functions, structures and defines in
i2c-core to i2c_acpi_ in order to have more consistent name space.
This is updated version from commit a7003b6580 ("i2c: core: Cleanup I2C
ACPI namespace") that got reverted due merge conflicts from
commit 525e6fabea ("i2c / ACPI: add support for ACPI reconfigure
notifications").
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch enabled high speed mode. High speed mode can be turn on by
setting the clk_freq to 3400000. High speed HCNT and LCNT are needed
as there is no default value provided.
Signed-off-by: Weifeng Voon <weifeng.voon@intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
DW_IC_CON_MASTER, DW_IC_CON_SLAVE_DISABLE and DW_IC_CON_RESTART_EN are
common config that need to be set for i2c designware master. So, configure
it first without having to repeat inside the if else.
Signed-off-by: Weifeng Voon <weifeng.voon@intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch enabled fast mode plus. The fast mode plus and fast speed
share the same HCNT and LCNT register. So, the fast mode plus will only
run when the HCNT and LCNT value is provided. Else, it will run at fast
speed as default.
Signed-off-by: Weifeng Voon <weifeng.voon@intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
I2C designware controller can run at fast mode plus and high speed. This
patch adds the capability to get the HCNT, LCNT configuration via
FPCN (fast plus) and HSCN (high speed) ACPI method.
Signed-off-by: Weifeng Voon <weifeng.voon@intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
I2c designware controller operate speed is configured in the register
IC_CON. Previously the operate speed is determined by a local variable
clk_freq. This patch will move the local variable clk_freq into struct
dw_i2c_dev. This change will ease the set and get of the clk_freq.
Signed-off-by: Weifeng Voon <weifeng.voon@intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Sort include files alphabetically to reduce probability of merge
conflicts.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The register offsets are different between Octeon and ThunderX so move
them into the algorithm struct and get rid of the define.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add SMBUS alert interrupt support. For now only device tree is
supported for specifying the alert. In case of ACPI an error
is returned.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The ThunderX SOC uses the same i2c block as the Octeon SOC.
The main difference is that on ThunderX the device is a PCI device
so device probing is done via PCI, interrupts are MSI-X. The
clock rates can be set via device tree or ACPI.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Move common functionality into a separate file in preparation of the
re-use from the ThunderX i2c driver.
Functions are slightly re-ordered but no other changes are included.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This is an intermediate commit in preparation of the driver split.
The module rename in this commit will be reverted in the next patch,
this is just done to make the series bisectible.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
No longer rely on the implicit matching with the i2c device name, use
an explicit compatible string instead.
Keep a direct pointer to the chip description instead of an index into
the chip description array.
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Peter Rosin <peda@axentia.se>
No longer rely on the implicit matching with the i2c device name, use
an explicit compatible string instead.
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Peter Rosin <peda@axentia.se>
The i2c mux core can then take appropriate action depending on if it is
used for an actual i2c mux, for a gate or for an arbitrator (the last
is the case for these drivers). This adds support for the new clearer
and more compact devicetree bindings that was added recently.
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Peter Rosin <peda@axentia.se>
Backwards compatibility is preserved; the subnodes are in practice
optional.
However, the mux core needs to know what subnode it should examine, so add
a couple of new flags for i2c_mux_alloc for this purpose.
The rule is that if the mux core finds a 'reg' property in the appropriate
subnode, e.g. if 'reg' exists in the 'i2c-mux' subnode, then the mux core
will assume that this is an old style entry and not an i2c-mux subnode
(correspondingly for arbitrators and gates with 'i2c-arb' and 'i2c-gate').
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Peter Rosin <peda@axentia.se>
We must use the same device we used for mapping.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We must use the same device we used for mapping.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Make sure the index to the active channel is invalidated when switching
fails.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This unifies usage with i2c_lock_bus and i2c_unlock_bus, and paves the
way for the next patch which looks a bit saner with this preparatory
work taken care of beforehand.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The core will do this for us now.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The core will do this for us now.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is only one waiter for the completion, therefore there
is no need to use complete_all(). Let's make that clear by
using complete() instead of complete_all().
The usage pattern of the completion is:
meson_i2c_xfer_msg()
reinit_completion()
...
/* Start the transfer */
...
wait_for_completion_timeout()
Signed-off-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is only one waiter for the completion, therefore there
is no need to use complete_all(). Let's make that clear by
using complete() instead of complete_all().
The usage pattern of the completion is:
brcmstb_send_i2c_cmd()
reinit_completion()
...
/* initiate transfer by setting iic_enable */
...
brcmstb_i2c_wait_for_completion()
Signed-off-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Reviewed-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is only one waiter for the completion, therefore there
is no need to use complete_all(). Let's make that clear by
using complete() instead of complete_all().
The usage pattern of the completion is:
bcm_kona_send_i2c_cmd()
reinit_completion()
...
bcm_kona_i2c_send_cmd_to_ctrl()
...
wait_for_completion_timeout()
Signed-off-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Tim Kryger <tim.kryger@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is only one waiter for the completion, therefore there
is no need to use complete_all(). Let's make that clear by
using complete() instead of complete_all().
The usage pattern of the completion is:
bcm_iproc_i2c_xfer_single_msg()
reinit_completion()
...
(activate the transfer)
...
wait_for_completion_timeout()
Signed-off-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The "alternative command" feature was introduced with sama5d2 SoCs.
Its purpose is to let the hardware i2c controller automatically send the
STOP condition on the i2c bus at the end of a data transfer.
Without this feature, the i2c driver has to write the 'STOP' bit into the
Control Register so the hardware i2c controller is triggered to send the
STOP condition on the bus.
Using the "alternative command" feature requires to set the transfer data
length into the 8bit DATAL field of the Alternative Command Register.
Hence only data transfers up to 255 bytes can take advantage of the
"alternative command" feature. For greater data transfer sizes, the driver
should use the previous implementation, when the "alternative command"
support was not implemented yet.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
clk_disable_unprepare() is missed on failure paths in ocores_i2c_probe().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
cros_ec_cmd_xfer returns success status if the command transport
completes successfully, but the execution result is incorrectly ignored.
In many cases, the execution result is assumed to be successful, leading
to ignored errors and operating on uninitialized data.
We've recently introduced the cros_ec_cmd_xfer_status() helper to avoid these
problems. Let's use it.
[Regarding the 'Fixes' tag; there is significant refactoring since the driver's
introduction, but the underlying logical error exists throughout I believe]
Fixes: 9d230c9e4f ("i2c: ChromeOS EC tunnel driver")
Cc: <stable@vger.kernel.org> # 9798ac6d32 mfd: cros_ec: Add cros_ec_cmd_xfer_status() helper
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We also need to revert the dynamic OF change, so we get a consistent
state again. Otherwise, we might have two devices enabled e.g. after
pinctrl setup fails.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Highlights:
- PowerNV PCI hotplug support.
- Lots more Power9 support.
- eBPF JIT support on ppc64le.
- Lots of cxl updates.
- Boot code consolidation.
Bug fixes:
- Fix spin_unlock_wait() from Boqun Feng
- Fix stack pointer corruption in __tm_recheckpoint() from Michael Neuling
- Fix multiple bugs in memory_hotplug_max() from Bharata B Rao
- mm: Ensure "special" zones are empty from Oliver O'Halloran
- ftrace: Separate the heuristics for checking call sites from Michael Ellerman
- modules: Never restore r2 for a mprofile-kernel style mcount() call from Michael Ellerman
- Fix endianness when reading TCEs from Alexey Kardashevskiy
- start rtasd before PCI probing from Greg Kurz
- PCI: rpaphp: Fix slot registration for multiple slots under a PHB from Tyrel Datwyler
- powerpc/mm: Add memory barrier in __hugepte_alloc() from Sukadev Bhattiprolu
Cleanups & fixes:
- Drop support for MPIC in pseries from Rashmica Gupta
- Define and use PPC64_ELF_ABI_v2/v1 from Michael Ellerman
- Remove unused symbols in asm-offsets.c from Rashmica Gupta
- Fix SRIOV not building without EEH enabled from Russell Currey
- Remove kretprobe_trampoline_holder. from Thiago Jung Bauermann
- Reduce log level of PCI I/O space warning from Benjamin Herrenschmidt
- Add array bounds checking to crash_shutdown_handlers from Suraj Jitindar Singh
- Avoid -maltivec when using clang integrated assembler from Anton Blanchard
- Fix array overrun in ppc_rtas() syscall from Andrew Donnellan
- Fix error return value in cmm_mem_going_offline() from Rasmus Villemoes
- export cpu_to_core_id() from Mauricio Faria de Oliveira
- Remove old symbols from defconfigs from Andrew Donnellan
- Update obsolete comments in setup_32.c about entry conditions from Benjamin Herrenschmidt
- Add comment explaining the purpose of setup_kdump_trampoline() from Benjamin Herrenschmidt
- Merge the RELOCATABLE config entries for ppc32 and ppc64 from Kevin Hao
- Remove RELOCATABLE_PPC32 from Kevin Hao
- Fix .long's in tlb-radix.c to more meaningful from Balbir Singh
Minor cleanups & fixes:
- Andrew Donnellan, Anna-Maria Gleixner, Anton Blanchard, Benjamin
Herrenschmidt, Bharata B Rao, Christophe Leroy, Colin Ian King, Geliang
Tang, Greg Kurz, Madhavan Srinivasan, Michael Ellerman, Michael Ellerman,
Stephen Rothwell, Stewart Smith.
Freescale updates from Scott:
- "Highlights include more 8xx optimizations, device tree updates,
and MVME7100 support."
PowerNV PCI hotplug from Gavin Shan:
- PCI: Add pcibios_setup_bridge()
- Override pcibios_setup_bridge()
- Remove PCI_RESET_DELAY_US
- Move pnv_pci_ioda_setup_opal_tce_kill() around
- Increase PE# capacity
- Allocate PE# in reverse order
- Create PEs in pcibios_setup_bridge()
- Setup PE for root bus
- Extend PCI bridge resources
- Make pnv_ioda_deconfigure_pe() visible
- Dynamically release PE
- Update bridge windows on PCI plug
- Delay populating pdn
- Support PCI slot ID
- Use PCI slot reset infrastructure
- Introduce pnv_pci_get_slot_id()
- Functions to get/set PCI slot state
- PCI/hotplug: PowerPC PowerNV PCI hotplug driver
- Print correct PHB type names
Power9 idle support from Shreyas B. Prabhu:
- set power_save func after the idle states are initialized
- Use PNV_THREAD_WINKLE macro while requesting for winkle
- make hypervisor state restore a function
- Rename idle_power7.S to idle_book3s.S
- Rename reusable idle functions to hardware agnostic names
- Make pnv_powersave_common more generic
- abstraction for saving SPRs before entering deep idle states
- Add platform support for stop instruction
- cpuidle/powernv: Use CPUIDLE_STATE_MAX instead of MAX_POWERNV_IDLE_STATES
- cpuidle/powernv: cleanup cpuidle-powernv.c
- cpuidle/powernv: Add support for POWER ISA v3 idle states
- Use deepest stop state when cpu is offlined
Power9 PMU from Madhavan Srinivasan:
- factor out power8 pmu macros and defines
- factor out power8 pmu functions
- factor out power8 __init_pmu code
- Add power9 event list macros for generic and cache events
- Power9 PMU support
- Export Power9 generic and cache events to sysfs
Power9 preliminary interrupt & PCI support from Benjamin Herrenschmidt:
- Add XICS emulation APIs
- Move a few exception common handlers to make room
- Add support for HV virtualization interrupts
- Add mechanism to force a replay of interrupts
- Add ICP OPAL backend
- Discover IODA3 PHBs
- pci: Remove obsolete SW invalidate
- opal: Add real mode call wrappers
- Rename TCE invalidation calls
- Remove SWINV constants and obsolete TCE code
- Rework accessing the TCE invalidate register
- Fallback to OPAL for TCE invalidations
- Use the device-tree to get available range of M64's
- Check status of a PHB before using it
- pci: Don't try to allocate resources that will be reassigned
Other Power9:
- Send SIGBUS on unaligned copy and paste from Chris Smart
- Large Decrementer support from Oliver O'Halloran
- Load Monitor Register Support from Jack Miller
Performance improvements from Anton Blanchard:
- Avoid load hit store in __giveup_fpu() and __giveup_altivec()
- Avoid load hit store in setup_sigcontext()
- Remove assembly versions of strcpy, strcat, strlen and strcmp
- Align hot loops of some string functions
eBPF JIT from Naveen N. Rao:
- Fix/enhance 32-bit Load Immediate implementation
- Optimize 64-bit Immediate loads
- Introduce rotate immediate instructions
- A few cleanups
- Isolate classic BPF JIT specifics into a separate header
- Implement JIT compiler for extended BPF
Operator Panel driver from Suraj Jitindar Singh:
- devicetree/bindings: Add binding for operator panel on FSP machines
- Add inline function to get rc from an ASYNC_COMP opal_msg
- Add driver for operator panel on FSP machines
Sparse fixes from Daniel Axtens:
- make some things static
- Introduce asm-prototypes.h
- Include headers containing prototypes
- Use #ifdef __BIG_ENDIAN__ #else for REG_BYTE
- kvm: Clarify __user annotations
- Pass endianness to sparse
- Make ppc_md.{halt, restart} __noreturn
MM fixes & cleanups from Aneesh Kumar K.V:
- radix: Update LPCR HR bit as per ISA
- use _raw variant of page table accessors
- Compile out radix related functions if RADIX_MMU is disabled
- Clear top 16 bits of va only on older cpus
- Print formation regarding the the MMU mode
- hash: Update SDR1 size encoding as documented in ISA 3.0
- radix: Update PID switch sequence
- radix: Update machine call back to support new HCALL.
- radix: Add LPID based tlb flush helpers
- radix: Add a kernel command line to disable radix
- Cleanup LPCR defines
Boot code consolidation from Benjamin Herrenschmidt:
- Move epapr_paravirt_early_init() to early_init_devtree()
- cell: Don't use flat device-tree after boot
- ge_imp3a: Don't use the flat device-tree after boot
- mpc85xx_ds: Don't use the flat device-tree after boot
- mpc85xx_rdb: Don't use the flat device-tree after boot
- Don't test for machine type in rtas_initialize()
- Don't test for machine type in smp_setup_cpu_maps()
- dt: Add of_device_compatible_match()
- Factor do_feature_fixup calls
- Move 64-bit feature fixup earlier
- Move 64-bit memory reserves to setup_arch()
- Use a cachable DART
- Move FW feature probing out of pseries probe()
- Put exception configuration in a common place
- Remove early allocation of the SMU command buffer
- Move MMU backend selection out of platform code
- pasemi: Remove IOBMAP allocation from platform probe()
- mm/hash: Don't use machine_is() early during boot
- Don't test for machine type to detect HEA special case
- pmac: Remove spurrious machine type test
- Move hash table ops to a separate structure
- Ensure that ppc_md is empty before probing for machine type
- Move 64-bit probe_machine() to later in the boot process
- Move 32-bit probe() machine to later in the boot process
- Get rid of ppc_md.init_early()
- Move the boot time info banner to a separate function
- Move setting of {i,d}cache_bsize to initialize_cache_info()
- Move the content of setup_system() to setup_arch()
- Move cache info inits to a separate function
- Re-order the call to smp_setup_cpu_maps()
- Re-order setup_panic()
- Make a few boot functions __init
- Merge 32-bit and 64-bit setup_arch()
Other new features:
- tty/hvc: Use IRQF_SHARED for OPAL hvc consoles from Sam Mendoza-Jonas
- tty/hvc: Use opal irqchip interface if available from Sam Mendoza-Jonas
- powerpc: Add module autoloading based on CPU features from Alastair D'Silva
- crypto: vmx - Convert to CPU feature based module autoloading from Alastair D'Silva
- Wake up kopald polling thread before waiting for events from Benjamin Herrenschmidt
- xmon: Dump ISA 2.06 SPRs from Michael Ellerman
- xmon: Dump ISA 2.07 SPRs from Michael Ellerman
- Add a parameter to disable 1TB segs from Oliver O'Halloran
- powerpc/boot: Add OPAL console to epapr wrappers from Oliver O'Halloran
- Assign fixed PHB number based on device-tree properties from Guilherme G. Piccoli
- pseries: Add pseries hotplug workqueue from John Allen
- pseries: Add support for hotplug interrupt source from John Allen
- pseries: Use kernel hotplug queue for PowerVM hotplug events from John Allen
- pseries: Move property cloning into its own routine from Nathan Fontenot
- pseries: Dynamic add entires to associativity lookup array from Nathan Fontenot
- pseries: Auto-online hotplugged memory from Nathan Fontenot
- pseries: Remove call to memblock_add() from Nathan Fontenot
cxl:
- Add set and get private data to context struct from Michael Neuling
- make base more explicitly non-modular from Paul Gortmaker
- Use for_each_compatible_node() macro from Wei Yongjun
- Frederic Barrat
- Abstract the differences between the PSL and XSL
- Make vPHB device node match adapter's
- Philippe Bergheaud
- Add mechanism for delivering AFU driver specific events
- Ignore CAPI adapters misplaced in switched slots
- Refine slice error debug messages
- Andrew Donnellan
- static-ify variables to fix sparse warnings
- PCI/hotplug: pnv_php: export symbols and move struct types needed by cxl
- PCI/hotplug: pnv_php: handle OPAL_PCI_SLOT_OFFLINE power state
- Add cxl_check_and_switch_mode() API to switch bi-modal cards
- remove dead Kconfig options
- fix potential NULL dereference in free_adapter()
- Ian Munsie
- Update process element after allocating interrupts
- Add support for CAPP DMA mode
- Fix allowing bogus AFU descriptors with 0 maximum processes
- Fix allocating a minimum of 2 pages for the SPA
- Fix bug where AFU disable operation had no effect
- Workaround XSL bug that does not clear the RA bit after a reset
- Fix NULL pointer dereference on kernel contexts with no AFU interrupts
- powerpc/powernv: Split cxl code out into a separate file
- Add cxl_slot_is_supported API
- Enable bus mastering for devices using CAPP DMA mode
- Move cxl_afu_get / cxl_afu_put to base
- Allow a default context to be associated with an external pci_dev
- Do not create vPHB if there are no AFU configuration records
- powerpc/powernv: Add support for the cxl kernel api on the real phb
- Add support for using the kernel API with a real PHB
- Add kernel APIs to get & set the max irqs per context
- Add preliminary workaround for CX4 interrupt limitation
- Add support for interrupts on the Mellanox CX4
- Workaround PE=0 hardware limitation in Mellanox CX4
- powerpc/powernv: Fix pci-cxl.c build when CONFIG_MODULES=n
selftests:
- Test unaligned copy and paste from Chris Smart
- Load Monitor Register Tests from Jack Miller
- Cyril Bur
- exec() with suspended transaction
- Use signed long to read perf_event_paranoid
- Fix usage message in context_switch
- Fix generation of vector instructions/types in context_switch
- Michael Ellerman
- Use "Delta" rather than "Error" in normal output
- Import Anton's mmap & futex micro benchmarks
- Add a test for PROT_SAO
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Z5kM
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Highlights:
- PowerNV PCI hotplug support.
- Lots more Power9 support.
- eBPF JIT support on ppc64le.
- Lots of cxl updates.
- Boot code consolidation.
Bug fixes:
- Fix spin_unlock_wait() from Boqun Feng
- Fix stack pointer corruption in __tm_recheckpoint() from Michael
Neuling
- Fix multiple bugs in memory_hotplug_max() from Bharata B Rao
- mm: Ensure "special" zones are empty from Oliver O'Halloran
- ftrace: Separate the heuristics for checking call sites from
Michael Ellerman
- modules: Never restore r2 for a mprofile-kernel style mcount() call
from Michael Ellerman
- Fix endianness when reading TCEs from Alexey Kardashevskiy
- start rtasd before PCI probing from Greg Kurz
- PCI: rpaphp: Fix slot registration for multiple slots under a PHB
from Tyrel Datwyler
- powerpc/mm: Add memory barrier in __hugepte_alloc() from Sukadev
Bhattiprolu
Cleanups & fixes:
- Drop support for MPIC in pseries from Rashmica Gupta
- Define and use PPC64_ELF_ABI_v2/v1 from Michael Ellerman
- Remove unused symbols in asm-offsets.c from Rashmica Gupta
- Fix SRIOV not building without EEH enabled from Russell Currey
- Remove kretprobe_trampoline_holder from Thiago Jung Bauermann
- Reduce log level of PCI I/O space warning from Benjamin
Herrenschmidt
- Add array bounds checking to crash_shutdown_handlers from Suraj
Jitindar Singh
- Avoid -maltivec when using clang integrated assembler from Anton
Blanchard
- Fix array overrun in ppc_rtas() syscall from Andrew Donnellan
- Fix error return value in cmm_mem_going_offline() from Rasmus
Villemoes
- export cpu_to_core_id() from Mauricio Faria de Oliveira
- Remove old symbols from defconfigs from Andrew Donnellan
- Update obsolete comments in setup_32.c about entry conditions from
Benjamin Herrenschmidt
- Add comment explaining the purpose of setup_kdump_trampoline() from
Benjamin Herrenschmidt
- Merge the RELOCATABLE config entries for ppc32 and ppc64 from Kevin
Hao
- Remove RELOCATABLE_PPC32 from Kevin Hao
- Fix .long's in tlb-radix.c to more meaningful from Balbir Singh
Minor cleanups & fixes:
- Andrew Donnellan, Anna-Maria Gleixner, Anton Blanchard, Benjamin
Herrenschmidt, Bharata B Rao, Christophe Leroy, Colin Ian King,
Geliang Tang, Greg Kurz, Madhavan Srinivasan, Michael Ellerman,
Michael Ellerman, Stephen Rothwell, Stewart Smith.
Freescale updates from Scott:
- "Highlights include more 8xx optimizations, device tree updates,
and MVME7100 support."
PowerNV PCI hotplug from Gavin Shan:
- PCI: Add pcibios_setup_bridge()
- Override pcibios_setup_bridge()
- Remove PCI_RESET_DELAY_US
- Move pnv_pci_ioda_setup_opal_tce_kill() around
- Increase PE# capacity
- Allocate PE# in reverse order
- Create PEs in pcibios_setup_bridge()
- Setup PE for root bus
- Extend PCI bridge resources
- Make pnv_ioda_deconfigure_pe() visible
- Dynamically release PE
- Update bridge windows on PCI plug
- Delay populating pdn
- Support PCI slot ID
- Use PCI slot reset infrastructure
- Introduce pnv_pci_get_slot_id()
- Functions to get/set PCI slot state
- PCI/hotplug: PowerPC PowerNV PCI hotplug driver
- Print correct PHB type names
Power9 idle support from Shreyas B. Prabhu:
- set power_save func after the idle states are initialized
- Use PNV_THREAD_WINKLE macro while requesting for winkle
- make hypervisor state restore a function
- Rename idle_power7.S to idle_book3s.S
- Rename reusable idle functions to hardware agnostic names
- Make pnv_powersave_common more generic
- abstraction for saving SPRs before entering deep idle states
- Add platform support for stop instruction
- cpuidle/powernv: Use CPUIDLE_STATE_MAX instead of MAX_POWERNV_IDLE_STATES
- cpuidle/powernv: cleanup cpuidle-powernv.c
- cpuidle/powernv: Add support for POWER ISA v3 idle states
- Use deepest stop state when cpu is offlined
Power9 PMU from Madhavan Srinivasan:
- factor out power8 pmu macros and defines
- factor out power8 pmu functions
- factor out power8 __init_pmu code
- Add power9 event list macros for generic and cache events
- Power9 PMU support
- Export Power9 generic and cache events to sysfs
Power9 preliminary interrupt & PCI support from Benjamin Herrenschmidt:
- Add XICS emulation APIs
- Move a few exception common handlers to make room
- Add support for HV virtualization interrupts
- Add mechanism to force a replay of interrupts
- Add ICP OPAL backend
- Discover IODA3 PHBs
- pci: Remove obsolete SW invalidate
- opal: Add real mode call wrappers
- Rename TCE invalidation calls
- Remove SWINV constants and obsolete TCE code
- Rework accessing the TCE invalidate register
- Fallback to OPAL for TCE invalidations
- Use the device-tree to get available range of M64's
- Check status of a PHB before using it
- pci: Don't try to allocate resources that will be reassigned
Other Power9:
- Send SIGBUS on unaligned copy and paste from Chris Smart
- Large Decrementer support from Oliver O'Halloran
- Load Monitor Register Support from Jack Miller
Performance improvements from Anton Blanchard:
- Avoid load hit store in __giveup_fpu() and __giveup_altivec()
- Avoid load hit store in setup_sigcontext()
- Remove assembly versions of strcpy, strcat, strlen and strcmp
- Align hot loops of some string functions
eBPF JIT from Naveen N. Rao:
- Fix/enhance 32-bit Load Immediate implementation
- Optimize 64-bit Immediate loads
- Introduce rotate immediate instructions
- A few cleanups
- Isolate classic BPF JIT specifics into a separate header
- Implement JIT compiler for extended BPF
Operator Panel driver from Suraj Jitindar Singh:
- devicetree/bindings: Add binding for operator panel on FSP machines
- Add inline function to get rc from an ASYNC_COMP opal_msg
- Add driver for operator panel on FSP machines
Sparse fixes from Daniel Axtens:
- make some things static
- Introduce asm-prototypes.h
- Include headers containing prototypes
- Use #ifdef __BIG_ENDIAN__ #else for REG_BYTE
- kvm: Clarify __user annotations
- Pass endianness to sparse
- Make ppc_md.{halt, restart} __noreturn
MM fixes & cleanups from Aneesh Kumar K.V:
- radix: Update LPCR HR bit as per ISA
- use _raw variant of page table accessors
- Compile out radix related functions if RADIX_MMU is disabled
- Clear top 16 bits of va only on older cpus
- Print formation regarding the the MMU mode
- hash: Update SDR1 size encoding as documented in ISA 3.0
- radix: Update PID switch sequence
- radix: Update machine call back to support new HCALL.
- radix: Add LPID based tlb flush helpers
- radix: Add a kernel command line to disable radix
- Cleanup LPCR defines
Boot code consolidation from Benjamin Herrenschmidt:
- Move epapr_paravirt_early_init() to early_init_devtree()
- cell: Don't use flat device-tree after boot
- ge_imp3a: Don't use the flat device-tree after boot
- mpc85xx_ds: Don't use the flat device-tree after boot
- mpc85xx_rdb: Don't use the flat device-tree after boot
- Don't test for machine type in rtas_initialize()
- Don't test for machine type in smp_setup_cpu_maps()
- dt: Add of_device_compatible_match()
- Factor do_feature_fixup calls
- Move 64-bit feature fixup earlier
- Move 64-bit memory reserves to setup_arch()
- Use a cachable DART
- Move FW feature probing out of pseries probe()
- Put exception configuration in a common place
- Remove early allocation of the SMU command buffer
- Move MMU backend selection out of platform code
- pasemi: Remove IOBMAP allocation from platform probe()
- mm/hash: Don't use machine_is() early during boot
- Don't test for machine type to detect HEA special case
- pmac: Remove spurrious machine type test
- Move hash table ops to a separate structure
- Ensure that ppc_md is empty before probing for machine type
- Move 64-bit probe_machine() to later in the boot process
- Move 32-bit probe() machine to later in the boot process
- Get rid of ppc_md.init_early()
- Move the boot time info banner to a separate function
- Move setting of {i,d}cache_bsize to initialize_cache_info()
- Move the content of setup_system() to setup_arch()
- Move cache info inits to a separate function
- Re-order the call to smp_setup_cpu_maps()
- Re-order setup_panic()
- Make a few boot functions __init
- Merge 32-bit and 64-bit setup_arch()
Other new features:
- tty/hvc: Use IRQF_SHARED for OPAL hvc consoles from Sam Mendoza-Jonas
- tty/hvc: Use opal irqchip interface if available from Sam Mendoza-Jonas
- powerpc: Add module autoloading based on CPU features from Alastair D'Silva
- crypto: vmx - Convert to CPU feature based module autoloading from Alastair D'Silva
- Wake up kopald polling thread before waiting for events from Benjamin Herrenschmidt
- xmon: Dump ISA 2.06 SPRs from Michael Ellerman
- xmon: Dump ISA 2.07 SPRs from Michael Ellerman
- Add a parameter to disable 1TB segs from Oliver O'Halloran
- powerpc/boot: Add OPAL console to epapr wrappers from Oliver O'Halloran
- Assign fixed PHB number based on device-tree properties from Guilherme G. Piccoli
- pseries: Add pseries hotplug workqueue from John Allen
- pseries: Add support for hotplug interrupt source from John Allen
- pseries: Use kernel hotplug queue for PowerVM hotplug events from John Allen
- pseries: Move property cloning into its own routine from Nathan Fontenot
- pseries: Dynamic add entires to associativity lookup array from Nathan Fontenot
- pseries: Auto-online hotplugged memory from Nathan Fontenot
- pseries: Remove call to memblock_add() from Nathan Fontenot
cxl:
- Add set and get private data to context struct from Michael Neuling
- make base more explicitly non-modular from Paul Gortmaker
- Use for_each_compatible_node() macro from Wei Yongjun
- Frederic Barrat
- Abstract the differences between the PSL and XSL
- Make vPHB device node match adapter's
- Philippe Bergheaud
- Add mechanism for delivering AFU driver specific events
- Ignore CAPI adapters misplaced in switched slots
- Refine slice error debug messages
- Andrew Donnellan
- static-ify variables to fix sparse warnings
- PCI/hotplug: pnv_php: export symbols and move struct types needed by cxl
- PCI/hotplug: pnv_php: handle OPAL_PCI_SLOT_OFFLINE power state
- Add cxl_check_and_switch_mode() API to switch bi-modal cards
- remove dead Kconfig options
- fix potential NULL dereference in free_adapter()
- Ian Munsie
- Update process element after allocating interrupts
- Add support for CAPP DMA mode
- Fix allowing bogus AFU descriptors with 0 maximum processes
- Fix allocating a minimum of 2 pages for the SPA
- Fix bug where AFU disable operation had no effect
- Workaround XSL bug that does not clear the RA bit after a reset
- Fix NULL pointer dereference on kernel contexts with no AFU interrupts
- powerpc/powernv: Split cxl code out into a separate file
- Add cxl_slot_is_supported API
- Enable bus mastering for devices using CAPP DMA mode
- Move cxl_afu_get / cxl_afu_put to base
- Allow a default context to be associated with an external pci_dev
- Do not create vPHB if there are no AFU configuration records
- powerpc/powernv: Add support for the cxl kernel api on the real phb
- Add support for using the kernel API with a real PHB
- Add kernel APIs to get & set the max irqs per context
- Add preliminary workaround for CX4 interrupt limitation
- Add support for interrupts on the Mellanox CX4
- Workaround PE=0 hardware limitation in Mellanox CX4
- powerpc/powernv: Fix pci-cxl.c build when CONFIG_MODULES=n
selftests:
- Test unaligned copy and paste from Chris Smart
- Load Monitor Register Tests from Jack Miller
- Cyril Bur
- exec() with suspended transaction
- Use signed long to read perf_event_paranoid
- Fix usage message in context_switch
- Fix generation of vector instructions/types in context_switch
- Michael Ellerman
- Use "Delta" rather than "Error" in normal output
- Import Anton's mmap & futex micro benchmarks
- Add a test for PROT_SAO"
* tag 'powerpc-4.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (263 commits)
powerpc/mm: Parenthesise IS_ENABLED() in if condition
tty/hvc: Use opal irqchip interface if available
tty/hvc: Use IRQF_SHARED for OPAL hvc consoles
selftests/powerpc: exec() with suspended transaction
powerpc: Improve comment explaining why we modify VRSAVE
powerpc/mm: Drop unused externs for hpte_init_beat[_v3]()
powerpc/mm: Rename hpte_init_lpar() and move the fallback to a header
powerpc/mm: Fix build break when PPC_NATIVE=n
crypto: vmx - Convert to CPU feature based module autoloading
powerpc: Add module autoloading based on CPU features
powerpc/powernv/ioda: Fix endianness when reading TCEs
powerpc/mm: Add memory barrier in __hugepte_alloc()
powerpc/modules: Never restore r2 for a mprofile-kernel style mcount() call
powerpc/ftrace: Separate the heuristics for checking call sites
powerpc: Merge 32-bit and 64-bit setup_arch()
powerpc/64: Make a few boot functions __init
powerpc: Re-order setup_panic()
powerpc: Re-order the call to smp_setup_cpu_maps()
powerpc/32: Move cache info inits to a separate function
powerpc/64: Move the content of setup_system() to setup_arch()
...
Pull i2c updates from Wolfram Sang:
"Here is the I2C pull request for 4.8:
- the core and i801 driver gained support for SMBus Host Notify
- core support for more than one address in DT
- i2c_add_adapter() has now better error messages. We can remove all
error messages from drivers calling it as a next step.
- bigger updates to rk3x driver to support rk3399 SoC
- the at24 eeprom driver got refactored and can now read special
variants with unique serials or fixed MAC addresses.
The rest is regular driver updates and bugfixes"
* 'i2c/for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (66 commits)
i2c: i801: use IS_ENABLED() instead of checking for built-in or module
Documentation: i2c: slave: give proper example for pm usage
Documentation: i2c: slave: describe buffer problems a bit better
i2c: bcm2835: Don't complain on -EPROBE_DEFER from getting our clock
i2c: i2c-smbus: drop useless stubs
i2c: efm32: fix a failure path in efm32_i2c_probe()
Revert "i2c: core: Cleanup I2C ACPI namespace"
Revert "i2c: core: Add function for finding the bus speed from ACPI"
i2c: Update the description of I2C_SMBUS
i2c: i2c-smbus: fix i2c_handle_smbus_host_notify documentation
eeprom: at24: tweak the loop_until_timeout() macro
eeprom: at24: add support for at24mac series
eeprom: at24: support reading the serial number for 24csxx
eeprom: at24: platform_data: use BIT() macro
eeprom: at24: split at24_eeprom_write() into specialized functions
eeprom: at24: split at24_eeprom_read() into specialized functions
eeprom: at24: hide the read/write loop behind a macro
eeprom: at24: call read/write functions via function pointers
eeprom: at24: coding style fixes
eeprom: at24: move at24_read() below at24_eeprom_write()
...
The IS_ENABLED() macro checks if a Kconfig symbol has been enabled either
built-in or as a module, use that macro instead of open coding the same.
Using the macro makes the code more readable by helping abstract away some
of the Kconfig built-in and module enable details.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
* acpi-tables:
ACPI: Rename configfs.c to acpi_configfs.c to prevent link error
ACPI: add support for loading SSDTs via configfs
ACPI: add support for configfs
efi / ACPI: load SSTDs from EFI variables
spi / ACPI: add support for ACPI reconfigure notifications
i2c / ACPI: add support for ACPI reconfigure notifications
ACPI: add support for ACPI reconfiguration notifiers
ACPI / scan: fix enumeration (visited) flags for bus rescans
ACPI / documentation: add SSDT overlays documentation
ACPI: ARM64: support for ACPI_TABLE_UPGRADE
ACPI / tables: introduce ARCH_HAS_ACPI_TABLE_UPGRADE
ACPI / tables: move arch-specific symbol to asm/acpi.h
ACPI / tables: table upgrade: refactor function definitions
ACPI / tables: table upgrade: use cacheable map for tables
Conflicts:
arch/arm64/include/asm/acpi.h
Fixes dmesg spam when we just need to wait a moment for the clock
driver to probe.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is the only failure path in efm32_i2c_probe(),
where clk_disable_unprepare() is missed.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fixes: 1b5b23718b ("i2c: efm32: new bus driver")
Cc: stable@kernel.org
This reverts commit a7003b65801e17a19617a509b2dbae3442ddd709.There were
too heavy merge conflicts and the driver code making use of this was not
ready yet anyhow. So, we wait one cycle.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This reverts commit 55d38d060e. There were
too heavy merge conflicts and the driver code making use of this was not
ready yet anyhow. So, we wait one cycle.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We support the SMBus Host Notify protocol now.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The parameter description is from a previous implementation, update
it to describe the actual implementation.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
1. The current QCOM I2C driver code is failing for transfer length
greater than 255. This is happening due to improper segments length
as the I2C DMA segments can be maximum of 256 bytes.
2. The transfer length tlen was being initialized with 0 for 256
bytes, which is being passed for DMA mappings resulting in improper
DMA mapping length.
This patch fixes the above said problems by initializing the block
count with the values calculated in qup_i2c_set_blk_data and calculating
the remaining length for last DMA segment. Also, the block data length
need to be decremented after each transfer. Additionally, this patch
corrects the tlen assignment for DMA mapping.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
1. Current QCOM I2C driver hangs when sending data to address 0x03-0x07
in some scenarios. The QUP controller generates invalid write in this
case, since these addresses are reserved for different bus formats.
2. Also, the error handling is done by I2C QUP ISR in the case of DMA
mode. The state need to be RESET in case of any error for clearing the
available data in FIFO, which otherwise leaves the BAM DMA controller
in hang state.
This patch fixes the above two issues by clearing the error bits from
I2C and QUP status in ISR in case of I2C error, QUP error and resets
the QUP state to clear the FIFO data.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The driver transfer to a message with NOACK always in any size.
If client (eg. EDID segment point message) needs NOACK condition, it can
use I2C_M_IGNORE_NAK flag.
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Acked-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The BCM7xxx ARM and MIPS based SoCs share a similar I2C hardware block.
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
ACPI 5 specification doesn't have property for the I2C bus speed but
I2cSerialBus resource descriptors which define each controller-slave
connection define the maximum speed supported by that connection.
Thus finding the maximum safe speed for the bus is to walk all
I2cSerialBus resources that are associated to I2C controller and use
the speed of slowest connection.
Add function i2c_acpi_find_bus_speed() to the i2c-core that adapter
drivers can call prior registering itself to core.
This implies two-step walk through the I2cSerialBus resources: call to
i2c_acpi_find_bus_speed() does the first scan and finds the safe bus
speed that adapter drivers can set up. Adapter driver registration does
the second scan when i2c-core creates the I2C slaves by calling the
i2c_acpi_register_devices(). In that way the bus speed is set in case
slave device probe gets called during registration and does
communication.
Implement this by reusing the existing ACPI I2C walk routines in the
i2c-core. Extend them so that slowest connection speed is saved during
the walk and I2C slaves are registered only when calling through the
i2c_acpi_register_devices() with the i2c_adapter pointer.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
I2C ACPI enumeration was originally implemented in another module under
drivers/acpi/ but was later moved into i2c-core with added support for
I2C ACPI operation region.
Rename these acpi_i2c_ prefixed functions, structures and defines in
i2c-core to i2c_acpi_ in order to have more consistent name space.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Now that we revisited all error messages, we can use pr_fmt for the
remaining pr_* messages to ensure consistent output.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use a warning loglevel instead of info and switch to dev_* for device
info. Also print which client was accessed.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use dev_err instead of pr_err for more details.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Switch to WARN if no adapter name is given, otherwise we won't know who
missed to do that. Add error message if device registration fails.
Update error message for missing algo to match style of the others.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Move recovery init to a seperate function to let have
i2c_register_adapter() less lines and to avoid goto and a label.
Refactor string handling there for consistency and to save some bytes.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
On error, we should give idr back to the pool in any case.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use devm_* APIs to simplify the code a bit.
This patch also fixes the memory leak when unload the module.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Liviu Dudau <Liviu.Dudau@arm.com>
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is no build dependency for this driver, so enable COMPILE_TEST to get
better build coverage.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Liviu Dudau <Liviu.Dudau@arm.com>
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch adds supports for I2C device enumeration and removal via
ACPI reconfiguration notifications that are send as a result of an
ACPI table load or unload operation.
The code is very similar with the device tree reconfiguration code
with only small differences in the way we test and set the enumerated
state of the device:
* the equivalent of device tree's OF_POPULATED flag is the
flags.visited field in the ACPI device and the following
wrappers are used to manipulate it: acpi_device_enumerated(),
acpi_device_set_enumerated() and acpi_device_clear_enumerated()
* the device tree code checks of status of the OF_POPULATED flag to
avoid trying to create duplicate Linux devices in two places: once
when the controller is probed, and once when the reconfigure event
is received; in the ACPI code the check is performed only once when
the ACPI namespace is searched because this code path is invoked in
both of the two mentioned cases
The rest of the enumeration handling is similar with device tree: when
the Linux device is unregistered the ACPI device is marked as not
enumerated; also, when a device remove notification is received we
check that the device is in the enumerated state before continuing
with the removal of the Linux device.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Added ACPI support for the I2C controller present on Broadcom's
Vulcan ARM64 processor. ACPI ID used by the controller is BRCM9007.
Changed the xlp9xx_i2c_get_frequency() function to use
device_property_read_u32() API so that the "clock-frequency" value
can be read from _DSD in ACPI mode.
Signed-off-by: Tanmay Jagdale <tanmay.jagdale@broadcom.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This driver should be buildable with COMPILE_TEST so
add this to the dependency for it.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is no code protecting i2c_dev to be freed after it is returned
from i2c_dev_get_by_minor() and using it to access the value which we
already have (minor) isn't safe really.
Avoid using it and get the adapter directly from 'minor'.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There are more than 7 busses, but only 7 are user visible. Update comment
accordingly.
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The i801 chip can handle the Host Notify feature since ICH 3 as mentioned
in http://www.intel.com/content/dam/doc/datasheet/82801ca-io-controller-hub-3-datasheet.pdf
Enable the functionality unconditionally and propagate the alert
on each notification.
With a T440s and a Synaptics touchpad that implements Host Notify, the
payload data is always 0x0000, so I am not sure if the device actually
sends the payload or if there is a problem regarding the implementation.
Tested-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
of_address_to_resource return 0 on successful call but
devm_ioremap_resource is called only if it returns non-zero value
Signed-off-by: Lukasz Gemborowski <lukasz.gemborowski@nokia.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
