commit 3091ae775f upstream.
Update the sh_pfc_soc_info pointer after calling the SoC-specific
initialization function, as it may have been updated to e.g. handle
different SoC revisions. This makes sure the correct subdriver name is
printed later.
Fixes: 0c151062f3 ("sh-pfc: Add support for SoC-specific initialization")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit da7a692fbb upstream.
The R8A7791 PFC driver was apparently based on the preliminary revisions
of the user's manual, which omitted the HSCIF1 group E signals in the
IPSR4 register description. This would cause HSCIF1's probe to fail with
the messages like below:
sh-pfc e6060000.pfc: cannot locate data/mark enum_id for mark 1989
sh-sci e62c8000.serial: Error applying setting, reverse things back
sh-sci: probe of e62c8000.serial failed with error -22
Add the neceassary PINMUX_IPSR_MSEL() invocations for the HSCK1_E,
HCTS1#_E, and HRTS1#_E signals...
Fixes: 5088451962 ("pinctrl: sh-pfc: r8a7791 PFC support")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit da6c2addf6 upstream.
To set the mux mode of a pin two bits must be set. Up to now this is
implemented using the following idiom:
writel(mask, reg + CLR);
writel(value, reg + SET);
. This however results in the mux mode being 0 between the two writes.
On my machine there is an IC's reset pin connected to LCD_D20. The
bootloader configures this pin as GPIO output-high (i.e. not holding the
IC in reset). When Linux reconfigures the pin to GPIO the short time
LCD_D20 is muxed as LCD_D20 instead of GPIO_1_20 is enough to confuse
the connected IC.
The same problem is present for the pin's drive strength setting which is
reset to low drive strength before using the right value.
So instead of relying on the hardware to modify the register setting
using two writes implement the bit toggling using read-modify-write.
Fixes: 17723111e6 ("pinctrl: add pinctrl-mxs support")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7903d4f5e1 upstream.
We use well known standard names for functions that have name, such as
I2C, SPI, SPDIF, etc..
Fix the function name of SPDIF, which was named OWA (One Wire Audio)
based on Allwinner datasheets.
Fixes: 4730f33f0d ("pinctrl: sunxi: add allwinner A83T PIO controller
support")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b7c747d462 upstream.
In stm32_pconf_parse_conf function, stm32_pmx_gpio_set_direction is
called with wrong parameter value. Indeed, using NULL value for range
will raise an oops.
Fixes: aceb16dc2d ("pinctrl: Add STM32 MCUs support")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 97ba26b8a9 upstream.
The nand_groups table uses different names for the NAND DQS pins than
the GROUP() definition in meson8b_cbus_groups (nand_dqs_0 vs nand_dqs0).
This prevents using the NAND DQS pins in the devicetree.
Fix this by ensuring that the GROUP() definition and the
meson8b_cbus_groups use the same name for these pins.
Fixes: 0fefcb6876 ("pinctrl: Add support for Meson8b")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3908632fb8 upstream.
The R8A7791 PFC driver was apparently based on the preliminary revisions
of the user's manual, which omitted the DVC_MUTE signal altogether in
the PFC section. The modern manual has the signal described, so just add
the necassary data to the driver...
Fixes: 5088451962 ("pinctrl: sh-pfc: r8a7791 PFC support")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 58439280f8 upstream.
PINMUX_IPSR_MSEL() macro invocation for the TX2 signal has apparently wrong
1st argument -- most probably a result of cut&paste programming...
Fixes: 5088451962 ("pinctrl: sh-pfc: r8a7791 PFC support")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5f4c8cafe1 upstream.
All R8A7794 manuals I have here (0.50 and 1.10) agree that the PFC driver
has ATAG0# and ATAWR0# signals in IPSR12 swapped -- fix this.
Fixes: 43c4436e2f ("pinctrl: sh-pfc: add R8A7794 PFC support")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7036502783 upstream.
After commit 47c950d102 ("pinctrl: cherryview: Do not add all
southwest and north GPIOs to IRQ domain") the driver does not add all
GPIOs to the irqdomain. The reason for that is that those GPIOs cannot
generate IRQs at all, only GPEs (General Purpose Events). This causes
Linux virtual IRQ numbering to change.
However, it seems some CYAN Chromebooks, including Acer Chromebook
hardcodes these Linux IRQ numbers in the ACPI tables of the machine.
Since the numbering is different now, the IRQ meant for keyboard does
not match the Linux virtual IRQ number anymore making the keyboard
non-functional.
Work this around by adding special quirk just for these machines where
we add back all GPIOs to the irqdomain. Rest of the Cherryview/Braswell
based machines will not be affected by the change.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=194945
Fixes: 47c950d102 ("pinctrl: cherryview: Do not add all southwest and north GPIOs to IRQ domain")
Reported-by: Adam S Levy <theadamlevy@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d7402de48e upstream.
This patch adds the missing PINGROUP for GPIO70-99.
This fixes a crash that happens in pinctrl-msm, if any
of the GPIO70-99 are accessed.
Fixes: 5303f7827f ("pinctrl: qcom: ipq4019: set ngpios to correct value")
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 17fab47369 ]
There are two bits in the PADCFG0 register to configure direction, one per
TX/RX buffers.
For now we wrongly assume that the GPIO is always requested before it is being
used, which is not true when the GPIO is used through irqchip. In this case the
GPIO is never requested and we never enable RX buffer for it.
Fix this by setting both bits accordingly.
Reported-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 827e1579e1 ]
The commit 04ff5a095d ("pinctrl: baytrail: Rectify debounce support")
almost fixes the logic of debuonce but missed couple of things, i.e.
typo in mask when disabling debounce and lack of enabling it back.
This patch addresses above issues.
Reported-by: Jean Delvare <jdelvare@suse.de>
Fixes: 04ff5a095d ("pinctrl: baytrail: Rectify debounce support")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a6566710ad upstream.
Clearing the status bit on irq_unmask will discard any pending interrupt
that did arrive after the irq_ack, i.e. while the IRQ handler function
was executing.
Fixes: f365be0925 ("pinctrl: Add Qualcomm TLMM driver")
Cc: Stephen Boyd <sboyd@codeaurora.org>
Reported-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1b89970d81 upstream.
Debounce value is set globally per community. Otherwise user will easily
get a kernel crash when they start using the feature:
BUG: unable to handle kernel paging request at ffffc900003be000
IP: byt_gpio_dbg_show+0xa9/0x430
Make it clear in byt_gpio_reg().
Note that this fix just prevents kernel to crash, but doesn't make any
difference to the existing logic. It means the last caller will win the
trade and debounce value will be configured accordingly. The actual
logic fix needs to be thought about and it's not as important as crash
fix. That's why the latter goes separately and right now.
Fixes: 658b476c74 ("pinctrl: baytrail: Add debounce configuration")
Cc: Cristina Ciocan <cristina.ciocan@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cdca06e4e8 upstream.
According to VLI64 Intel Atom E3800 Specification Update (#329901)
concurrent read accesses may result in returning 0xffffffff and write
accesses may be dropped silently.
To workaround all accesses must be protected by locks.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 04ff5a095d upstream.
The commit 658b476c74 ("pinctrl: baytrail: Add debounce configuration")
implements debounce for Baytrail pin control, but seems wasn't tested properly.
The register which keeps debounce value is separated from the configuration
one. Writing wrong values to the latter will guarantee wrong behaviour of the
driver and even might break something physically.
Besides above there is missed case how to disable it, which is actually done
through the bit in configuration register.
Rectify implementation here by using proper register for debounce value.
Fixes: 658b476c74 ("pinctrl: baytrail: Add debounce configuration")
Cc: Cristina Ciocan <cristina.ciocan@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ecc8995363 upstream.
PADCFGLOCK (and PADCFGLOCK_TX) offset in Broxton actually starts at 0x060
and not 0x090 as used in the driver. Fix it to use the correct offset.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5d7400c4ac upstream.
Always stating PIN_CONFIG_BIAS_DISABLE is supported gives untrue output
when examining /sys/kernel/debug/pinctrl/e6060000.pfc/pinconf-pins if
the operation get_bias() is implemented but the pin is not handled by
the get_bias() implementation. In that case the output will state that
"input bias disabled" indicating that this pin has bias control
support.
Make support for PIN_CONFIG_BIAS_DISABLE depend on that the pin either
supports SH_PFC_PIN_CFG_PULL_UP or SH_PFC_PIN_CFG_PULL_DOWN. This also
solves the issue where SoC specific implementations print error messages
if their particular implementation of {set,get}_bias() is called with a
pin it does not know about.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f24d311f92 upstream.
The pinctrl_gpio_request is called with the "full" gpio number, already
containing the base, then meson_pmx_request_gpio is then called with the
final pin number.
Remove the base addition when calling meson_pmx_disable_other_groups.
Fixes: 6ac7309511 ("pinctrl: add driver for Amlogic Meson SoCs")
CC: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Acked-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c314c9f15a upstream.
On some SoC there are no simple mapping of pins to bias register bits
and a lookup table is needed. This logic is already implemented in some
SoC specific drivers that could benefit from a generic implementation.
Add helpers to deal with the lookup which later can be used by the SoC
specific drivers. The logic used to lookup are different from the one it
aims to replace, this is intentional. This new method reduces the memory
consumption at the cost of increased CPU usage and fix a bug where a
WARN() would incorrectly be triggered if the register offset is 0.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d3b861bccd upstream.
There is a bug in the r8a7795 bias code where a WARN() is trigged
anytime a pin from PUEN0/PUD0 is accessed.
# cat /sys/kernel/debug/pinctrl/e6060000.pfc/pinconf-pins
WARNING: CPU: 2 PID: 2391 at drivers/pinctrl/sh-pfc/pfc-r8a7795.c:5364 r8a7795_pinmux_get_bias+0xbc/0xc8
[..]
Call trace:
[<ffff0000083c442c>] r8a7795_pinmux_get_bias+0xbc/0xc8
[<ffff0000083c37f4>] sh_pfc_pinconf_get+0x194/0x270
[<ffff0000083b0768>] pin_config_get_for_pin+0x20/0x30
[<ffff0000083b11e8>] pinconf_generic_dump_one+0x168/0x188
[<ffff0000083b144c>] pinconf_generic_dump_pins+0x5c/0x98
[<ffff0000083b0628>] pinconf_pins_show+0xc8/0x128
[<ffff0000081fe3bc>] seq_read+0x16c/0x420
[<ffff00000831a110>] full_proxy_read+0x58/0x88
[<ffff0000081d7ad4>] __vfs_read+0x1c/0xf8
[<ffff0000081d8874>] vfs_read+0x84/0x148
[<ffff0000081d9d64>] SyS_read+0x44/0xa0
[<ffff000008082f4c>] __sys_trace_return+0x0/0x4
This is due to the WARN() check if the reg field of the pullups struct
is zero, and this should be 0 for pins controlled by the PUEN0/PUD0
registers since PU0 is defined as 0. Change the data structure and use
the generic sh_pfc_pin_to_bias_info() function to get the register
offset and bit information.
Fixes: 560655247b ("pinctrl: sh-pfc: r8a7795: Add bias pinconf support")
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2983f296f2 upstream.
In the function amd_gpio_irq_set_type, read the values from
the ACPI table to set the level and drop the settings passed
by the client.
Reviewed-by: Pankaj Sen <Pankaj.Sen@amd.com>
Reviewed-by: Nitesh Kumar Agrawal <Nitesh-kumar.Agrawal@amd.com>
Reviewed-by: Shah, Nehal-bakulchandra <Nehal-bakulchandra.Shah@amd.com>
Signed-off-by: Shyam-sundar S-k <Shyam-sundar.S-k@amd.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a pin depending on bit 6 in SCU90 is requested for GPIO, the export
will succeed but changes to the GPIO's value will not be accepted by the
hardware. This is because the pinmux driver has misconfigured the SCU by
writing 1 to the reserved bit.
The description of SCU90[6] from the datasheet is 'Reserved, must keep
at value ”0”'. The fix is to switch pinmux from the bit-flipping macro
to explicitly configuring the .enable and .disable values to zero.
The patch has been tested on an AST2500 EVB.
Fixes: 56e57cb6c0 (pinctrl: Add pinctrl-aspeed-g5 driver)
Reported-by: Uma Yadlapati <yadlapat@us.ibm.com>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When the system is suspended to S3 the BIOS might re-initialize certain
GPIO pins back to their original state or it may re-program interrupt mask
of others. For example Acer TravelMate B116-M had BIOS bug where certain
GPIO pin (MF_ISH_GPIO_5) was programmed to trigger on high level, and the
pin state was high once the BIOS gave control to the OS on resume.
This triggers lots of messages like:
irq 117, desc: ffff88017a61e600, depth: 1, count: 0, unhandled: 0
->handle_irq(): ffffffff8109b613, handle_bad_irq+0x0/0x1e0
->irq_data.chip(): ffffffffa0020180, chv_pinctrl_exit+0x2d84/0x12 [pinctrl_cherryview]
->action(): (null)
IRQ_NOPROBE set
We reset the mask back to known state in chv_pinctrl_resume() but that is
called only after device interrupts have already been enabled.
Now, this particular issue was fixed by upgrading the BIOS to the latest
(v1.23) but not everybody upgrades their BIOSes so we fix it up in the
driver as well.
Prevent the possible interrupt storm by moving suspend and resume hooks to
be called at _noirq time instead. Since device interrupts are still
disabled we can restore the mask back to known state before interrupt storm
happens.
Cc: stable@vger.kernel.org
Reported-by: Christian Steiner <christian.steiner@outlook.de>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If async suspend is enabled, the driver may access registers concurrently
with another instance which may fail because of the bug in Cherryview GPIO
hardware. Prevent this by taking the shared lock while accessing the
hardware in suspend and resume hooks.
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Group index is incremented on every new group parsed. Since the
field is part of struct imx_pinctrl_soc_info, which is typically
a global variable passed by the individual pinctrl-imx.c based
driver, it does not get cleared automatically when re-probing the
driver. This lead imx_pinctrl_parse_functions passing a group
pointer which is outside of the allocated group space on second
probe and onwards. Typically this ended up in a NULL pointer
dereference when accessing the name field like this:
Unable to handle kernel NULL pointer dereference at virtual address 00000000
...
PC is at strcmp+0x18/0x44
LR is at imx_dt_node_to_map+0xc4/0x290
Avoid this by setting group_index to 0 on probe.
This has been observed when using DEBUG_TEST_DRIVER_REMOVE.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch allows to probe stm32 pinctrl driver even if no interrupt
controller is defined to manage gpio irqs.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Thanks to 332e99d5ae which now alerts of default
trigger usage when configuring interrupts.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since commit 44a7185c2a ("of/platform: Add common method to populate
default bus"), ARM64 platform devices are populated at the
arch_initcall_sync level; as a result, the platform_driver_probe calls
in both the iProc and NSP GPIO drivers fail with -ENODEV since by that
time the platform device was not yet registered.
Replace platform_driver_probe with platform_driver_register, that allow
the device to be register later
Fixes: 44a7185c2a ("of/platform: Add common method to populate default bus")
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Tested-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Dell XPS 13 (and maybe some others) uses a GPIO (CPU_GP_1) during suspend
to explicitly disable USB touchscreen interrupt. This is done to prevent
situation where the lid is closed the touchscreen is left functional.
The pinctrl driver (wrongly) assumes it owns all pins which are owned by
host and not locked down. It is perfectly fine for BIOS to use those pins
as it is also considered as host in this context.
What happens is that when the lid of Dell XPS 13 is closed, the BIOS
configures CPU_GP_1 low disabling the touchscreen interrupt. During resume
we restore all host owned pins to the known state which includes CPU_GP_1
and this overwrites what the BIOS has programmed there causing the
touchscreen to fail as no interrupts are reaching the CPU anymore.
Fix this by restoring only those pins we know are explicitly requested by
the kernel one way or other.
Cc: stable@vger.kernel.org
Link: https://bugzilla.kernel.org/show_bug.cgi?id=176361
Reported-by: AceLan Kao <acelan.kao@canonical.com>
Tested-by: AceLan Kao <acelan.kao@canonical.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Initialize the spinlock before using it.
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
CPU: 2 PID: 1 Comm: swapper/0 Not tainted 4.8.0-dwc-bisect #4
Hardware name: Intel Corp. VALLEYVIEW C0 PLATFORM/BYT-T FFD8, BIOS BLAKFF81.X64.0088.R10.1403240443 FFD8_X64_R_2014_13_1_00 03/24/2014
0000000000000000 ffff8800788ff770 ffffffff8133d597 0000000000000000
0000000000000000 ffff8800788ff7e0 ffffffff810cfb9e 0000000000000002
ffff8800788ff7d0 ffffffff8205b600 0000000000000002 ffff8800788ff7f0
Call Trace:
[<ffffffff8133d597>] dump_stack+0x67/0x90
[<ffffffff810cfb9e>] register_lock_class+0x52e/0x540
[<ffffffff810d2081>] __lock_acquire+0x81/0x16b0
[<ffffffff810cede1>] ? save_trace+0x41/0xd0
[<ffffffff810d33b2>] ? __lock_acquire+0x13b2/0x16b0
[<ffffffff810cf05a>] ? __lock_is_held+0x4a/0x70
[<ffffffff810d3b1a>] lock_acquire+0xba/0x220
[<ffffffff8136f1fe>] ? byt_gpio_get_direction+0x3e/0x80
[<ffffffff81631567>] _raw_spin_lock_irqsave+0x47/0x60
[<ffffffff8136f1fe>] ? byt_gpio_get_direction+0x3e/0x80
[<ffffffff8136f1fe>] byt_gpio_get_direction+0x3e/0x80
[<ffffffff813740a9>] gpiochip_add_data+0x319/0x7d0
[<ffffffff81631723>] ? _raw_spin_unlock_irqrestore+0x43/0x70
[<ffffffff8136fe3b>] byt_pinctrl_probe+0x2fb/0x620
[<ffffffff8142fb0c>] platform_drv_probe+0x3c/0xa0
...
Based on the diff it looks like the problem was introduced in
commit 71e6ca61e8 ("pinctrl: baytrail: Register pin control handling")
but I wasn't able to verify that empirically as the parent commit
just oopsed when I tried to boot it.
Cc: Cristina Ciocan <cristina.ciocan@intel.com>
Cc: stable@vger.kernel.org
Fixes: 71e6ca61e8 ("pinctrl: baytrail: Register pin control handling")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The SPI1 function was associated with the wrong pins: The functions that
those pins provide is either an SPI debug or passthrough function
coupled to SPI1. Make the SPI1 mux function configure the relevant pins
and associate new SPI1DEBUG and SPI1PASSTHRU functions with the pins
that were already defined.
The notation used in the datasheet's multi-function pin table for the SoC is
often creative: in this case the SYS* signals are enabled by a single bit,
which is nothing unusual on its own, but in this case the bit was also
participating in a multi-bit bitfield and therefore represented multiple
functions. This fact was overlooked in the original patch.
Fixes: 56e57cb6c0 (pinctrl: Add pinctrl-aspeed-g5 driver)
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This prevented C20 from successfully being muxed as GPIO.
Fixes: 56e57cb6c0 (pinctrl: Add pinctrl-aspeed-g5 driver)
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fixes simple typos in the initial commit. There is no behavioural
change.
Fixes: 56e57cb6c0 (pinctrl: Add pinctrl-aspeed-g5 driver)
Reported-by: Xo Wang <xow@google.com>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Consider a scenario with one pin P that has two signals A and B, where A
is defined to be higher priority than B: That is, if the mux IP is in a
state that would consider both A and B to be active on P, then A will be
the active signal.
To instead configure B as the active signal we must configure the mux so
that A is inactive. The mux state for signals can be described by
logical operations on one or more bits from one or more registers (a
"signal expression"), which in some cases leads to aliased mux states for
a particular signal. Further, signals described by multi-bit bitfields
often do not only need to record the states that would make them active
(the "enable" expressions), but also the states that makes them inactive
(the "disable" expressions). All of this combined leads to four possible
states for a signal:
1. A signal is active with respect to an "enable" expression
2. A signal is not active with respect to an "enable" expression
3. A signal is inactive with respect to a "disable" expression
4. A signal is not inactive with respect to a "disable" expression
In the case of P, if we are looking to activate B without explicitly
having configured A it's enough to consider A inactive if all of A's
"enable" signal expressions evaluate to "not active". If any evaluate to
"active" then the corresponding "disable" states must be applied so it
becomes inactive.
For example, on the AST2400 the pins composing GPIO bank H provide
signals ROMD8 through ROMD15 (high priority) and those for UART6 (low
priority). The mux states for ROMD8 through ROMD15 are aliased, i.e.
there are two mux states that result in the respective signals being
configured:
A. SCU90[6]=1
B. Strap[4,1:0]=100
Further, the second mux state is a 3-bit bitfield that explicitly
defines the enabled state but the disabled state is implicit, i.e. if
Strap[4,1:0] is not exactly "100" then ROMD8 through ROMD15 are not
considered active. This requires the mux function evaluation logic to
use approach 2. above, however the existing code was using approach 3.
The problem was brought to light on the Palmetto machines where the
strap register value is 0x120ce416, and prevented GPIO requests in bank
H from succeeding despite the hardware being in a position to allow
them.
Fixes: 318398c09a8d ("pinctrl: Add core pinctrl support for Aspeed SoCs")
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Driver updates for ARM SoCs, including a couple of newly added drivers:
- The Qualcomm external bus interface 2 (EBI2), used in some of their
mobile phone chips for connecting flash memory, LCD displays or
other peripherals
- Secure monitor firmware for Amlogic SoCs, and an NVMEM driver for the
EFUSE based on that firmware interface.
- Perf support for the AppliedMicro X-Gene performance monitor unit
- Reset driver for STMicroelectronics STM32
- Reset driver for SocioNext UniPhier SoCs
Aside from these, there are minor updates to SoC-specific bus,
clocksource, firmware, pinctrl, reset, rtc and pmic drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=GvTq
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"Driver updates for ARM SoCs, including a couple of newly added
drivers:
- The Qualcomm external bus interface 2 (EBI2), used in some of their
mobile phone chips for connecting flash memory, LCD displays or
other peripherals
- Secure monitor firmware for Amlogic SoCs, and an NVMEM driver for
the EFUSE based on that firmware interface.
- Perf support for the AppliedMicro X-Gene performance monitor unit
- Reset driver for STMicroelectronics STM32
- Reset driver for SocioNext UniPhier SoCs
Aside from these, there are minor updates to SoC-specific bus,
clocksource, firmware, pinctrl, reset, rtc and pmic drivers"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (50 commits)
bus: qcom-ebi2: depend on HAS_IOMEM
pinctrl: mvebu: orion5x: Generalise mv88f5181l support for 88f5181
clk: mvebu: Add clk support for the orion5x SoC mv88f5181
dt-bindings: EXYNOS: Add Exynos5433 PMU compatible
clocksource: exynos_mct: Add the support for ARM64
perf: xgene: Add APM X-Gene SoC Performance Monitoring Unit driver
Documentation: Add documentation for APM X-Gene SoC PMU DTS binding
MAINTAINERS: Add entry for APM X-Gene SoC PMU driver
bus: qcom: add EBI2 driver
bus: qcom: add EBI2 device tree bindings
rtc: rtc-pm8xxx: Add support for pm8018 rtc
nvmem: amlogic: Add Amlogic Meson EFUSE driver
firmware: Amlogic: Add secure monitor driver
soc: qcom: smd: Reset rx tail rather than tx
memory: atmel-sdramc: fix a possible NULL dereference
reset: hi6220: allow to compile test driver on other architectures
reset: zynq: add driver Kconfig option
reset: sunxi: add driver Kconfig option
reset: stm32: add driver Kconfig option
reset: socfpga: add driver Kconfig option
...
Subsystem improvements:
- Do away with the last users of the obsolete Kconfig options
ARCH_REQUIRE_GPIOLIB and ARCH_WANT_OPTIONAL_GPIOLIB (the latter
always sounded like an item on a wishlist to Santa Claus to
me). We can now select GPIOLIB and be done with it, for all
archs. After some struggle it even work on UM. Not that it has
GPIO, but if it wants to, it can select the library.
- Continued efforts to make drivers properly either tristate or
bool.
- Introduce a warning for drivers assigning default triggers to
their irqchip lines when probed from device tree, so we find and
fix these ambigous drivers. It is agreed that in the OF config
path, the device tree defines trigger characteristics.
- The same warning, mutatis mutandis, for ACPI-probed GPIO
irqchips.
- We introduce the ability to mark certain IRQ lines as "unusable"
as they can be taken by BIOS/firmware, unrouted in silicon and
generally nasty if you use them, and such things. This is
put to good use in the STMPE driver and also in the Cherryview
pin control driver.
- A new "mockup" virtual GPIO device that can be used for testing.
The plan is to add unit tests under tools/* for exercising this
device and verify that the kernel code paths are working as they
should.
- Make memory-mapped I/O-drivers depend on HAS_IOMEM. This was
implicit all the time, but when people started building UM
with allyesconfig or allmodconfig it exploded in their face.
- Move some stray bits of device tree and ACPI HW description
callbacks down into their respective implementation silo. These
were causing issues when compiling on !HAS_IOMEM as well, so
now eventually UM compiles the GPIOLIB library if it wants to.
New drivers:
- New driver for the Aspeed GPIO front-end companion to the
pin controller merged through the pin control tree.
- New driver for the LP873x PMIC GPIO portions.
- New driver for Technologic Systems' I2C FPGA GPIO such as
TS4900, TS-7970, TS-7990 and TS-4100.
- New driver for the Broadcom BCM63xx series including BCM6338
and BCM6345.
- New driver for the Intel WhiskeyCove PMIC GPIO.
- New driver for the Allwinner AXP209 PMIC GPIO portions.
- New driver for Diamond Systems 48 line GPIO-MM, another of
these port-mapped I/O expansion cards.
- Support the STMicroelectronics STMPE1600 variant in the STMPE
driver.
Driver improvements:
- The STMPE driver now supports rising/falling edge detection
properly for IRQs.
- The PCA954x will now fetch and enable its VCC regulator properly.
- Major rework of the PCA953x driver with the goal of eventually
switching it over to use regmap and thus modernize it even more.
- Switch the IOP driver to use the generic MMIO GPIO library.
- Move the ages old HTC EGPIO (extended GPIO) GPIO expander driver
over to this subsystem from MFD, achieveing some separation of
concerns.
-----BEGIN PGP SIGNATURE-----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=ABbi
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.9 series:
Subsystem improvements:
- do away with the last users of the obsolete Kconfig options
ARCH_REQUIRE_GPIOLIB and ARCH_WANT_OPTIONAL_GPIOLIB (the latter
always sounded like an item on a wishlist to Santa Claus to me). We
can now select GPIOLIB and be done with it, for all archs. After
some struggle it even work on UM. Not that it has GPIO, but if it
wants to, it can select the library.
- continued efforts to make drivers properly either tristate or bool.
- introduce a warning for drivers assigning default triggers to their
irqchip lines when probed from device tree, so we find and fix
these ambigous drivers. It is agreed that in the OF config path,
the device tree defines trigger characteristics.
- the same warning, mutatis mutandis, for ACPI-probed GPIO irqchips.
- we introduce the ability to mark certain IRQ lines as "unusable" as
they can be taken by BIOS/firmware, unrouted in silicon and
generally nasty if you use them, and such things. This is put to
good use in the STMPE driver and also in the Cherryview pin control
driver.
- a new "mockup" virtual GPIO device that can be used for testing.
The plan is to add unit tests under tools/* for exercising this
device and verify that the kernel code paths are working as they
should.
- make memory-mapped I/O-drivers depend on HAS_IOMEM. This was
implicit all the time, but when people started building UM with
allyesconfig or allmodconfig it exploded in their face.
- move some stray bits of device tree and ACPI HW description
callbacks down into their respective implementation silo. These
were causing issues when compiling on !HAS_IOMEM as well, so now
eventually UM compiles the GPIOLIB library if it wants to.
New drivers:
- new driver for the Aspeed GPIO front-end companion to the pin
controller merged through the pin control tree.
- new driver for the LP873x PMIC GPIO portions.
- new driver for Technologic Systems' I2C FPGA GPIO such as TS4900,
TS-7970, TS-7990 and TS-4100.
- new driver for the Broadcom BCM63xx series including BCM6338 and
BCM6345.
- new driver for the Intel WhiskeyCove PMIC GPIO.
- new driver for the Allwinner AXP209 PMIC GPIO portions.
- new driver for Diamond Systems 48 line GPIO-MM, another of these
port-mapped I/O expansion cards.
- support the STMicroelectronics STMPE1600 variant in the STMPE
driver.
Driver improvements:
- the STMPE driver now supports rising/falling edge detection
properly for IRQs.
- the PCA954x will now fetch and enable its VCC regulator properly.
- major rework of the PCA953x driver with the goal of eventually
switching it over to use regmap and thus modernize it even more.
- switch the IOP driver to use the generic MMIO GPIO library.
- move the ages old HTC EGPIO (extended GPIO) GPIO expander driver
over to this subsystem from MFD, achieveing some separation of
concerns"
* tag 'gpio-v4.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (81 commits)
gpio: add missing static inline
gpio: OF: localize some gpiochip init functions
gpio: acpi: separation of concerns
gpio: OF: separation of concerns
gpio: make memory-mapped drivers depend on HAS_IOMEM
gpio: stmpe: use BIT() macro
gpio: stmpe: forbid unused lines to be mapped as IRQs
mfd/gpio: Move HTC GPIO driver to GPIO subsystem
gpio: MAINTAINERS: Add an entry for GPIO mockup driver
gpio/mockup: add virtual gpio device
gpio: Added zynq specific check for special pins on bank zero
gpio: axp209: Implement get_direction
gpio: aspeed: remove redundant return value check
gpio: loongson1: remove redundant return value check
ARM: omap2: fix missing include
gpio: tc3589x: fix up complaints on unsigned
gpio: tc3589x: add .get_direction() and small cleanup
gpio: f7188x: use gpiochip_get_data instead of container_of
gpio: tps65218: use devm_gpiochip_add_data() for gpio registration
gpio: aspeed: fix return value check in aspeed_gpio_probe()
...
The following commit introduced a regression by not properly masking the
calculated value.
Fixes: 47a01ee9a6 ("pinctrl: qcom: Clear all function selection bits")
Signed-off-by: John Crispin <john@phrozen.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The generic GPIO library directly implement code for acpi_find_gpio()
which is only used with CONFIG_ACPI. This was probably done because
OF did the same thing, but I removed that so remove this too.
Rename the internal acpi_find_gpio() in gpiolib-acpi.c to
acpi_populate_gpio_lookup() which seems to be more appropriate anyway
so as to avoid a namespace clash with the same function.
Make the stub return -ENOENT rather than -ENOSYS (as that is for
syscalls!).
For some reason the sunxi pin control driver was including the private
gpiolib header, it works just fine without it so remove that oneliner.
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On some Intel BXT platform, wake-up from suspend-to-idle on pressing
power-button is not working. Its noticed that gpio-keys driver marking the
second level IRQ/power-button as wake capable but Intel pintctrl
driver is missing to mark GPIO chip/controller IRQ which first level IRQ
as wake cable if its GPIO pin IRQ is wakeble. So, though the first level
IRQ gets generated on power-button press, since it is not marked as
wake capable resume/wake-up flow is not happening.
Intel pintctrl/GPIO driver need to mark GPIO chip/controller IRQ (first
level IRQ) as wake capable iff GPIO pin's IRQ (second level IRQ) is marked
as wake cable.
Changes in v2:
- Add missing irq initialisation.
Signed-off-by: Nilesh Bacchewar <nilesh.bacchewar@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This simplifies the error handling and allows us to drop the whole
chv_pinctrl_remove() function.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It turns out that for north and southwest communities, they can only
generate GPIO interrupts for lower 8 interrupts (IntSel value). The upper
part (8-15) can only generate GPEs (General Purpose Events).
Now the reason why EC events such as pressing hotkeys does not work if we
mask all the interrupts is that in order to generate either interrupts or
GPEs the INTMASK register must have that particular interrupt unmasked. In
case of GPEs the CPU does not trigger normal interrupt (and thus the GPIO
driver does not see it) but instead it causes SCI (System Control
Interrupt) to be triggered with the GPE in question set.
To make this all work as expected we only add those GPIOs to the IRQ domain
that can actually generate interrupts (IntSel value 0-7) and skip others.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Geert Uytterhoeven