* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (134 commits)
powerpc/nvram: Enable use Generic NVRAM driver for different size chips
powerpc/iseries: Fix oops reading from /proc/iSeries/mf/*/cmdline
powerpc/ps3: Workaround for flash memory I/O error
powerpc/booke: Don't set DABR on 64-bit BookE, use DAC1 instead
powerpc/perf_counters: Reduce stack usage of power_check_constraints
powerpc: Fix bug where perf_counters breaks oprofile
powerpc/85xx: Fix SMP compile error and allow NULL for smp_ops
powerpc/irq: Improve nanodoc
powerpc: Fix some late PowerMac G5 with PCIe ATI graphics
powerpc/fsl-booke: Use HW PTE format if CONFIG_PTE_64BIT
powerpc/book3e: Add missing page sizes
powerpc/pseries: Fix to handle slb resize across migration
powerpc/powermac: Thermal control turns system off too eagerly
powerpc/pci: Merge ppc32 and ppc64 versions of phb_scan()
powerpc/405ex: support cuImage via included dtb
powerpc/405ex: provide necessary fixup function to support cuImage
powerpc/40x: Add support for the ESTeem 195E (PPC405EP) SBC
powerpc/44x: Add Eiger AMCC (AppliedMicro) PPC460SX evaluation board support.
powerpc/44x: Update Arches defconfig
powerpc/44x: Update Arches dts
...
Fix up conflicts in drivers/char/agp/uninorth-agp.c
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1623 commits)
netxen: update copyright
netxen: fix tx timeout recovery
netxen: fix file firmware leak
netxen: improve pci memory access
netxen: change firmware write size
tg3: Fix return ring size breakage
netxen: build fix for INET=n
cdc-phonet: autoconfigure Phonet address
Phonet: back-end for autoconfigured addresses
Phonet: fix netlink address dump error handling
ipv6: Add IFA_F_DADFAILED flag
net: Add DEVTYPE support for Ethernet based devices
mv643xx_eth.c: remove unused txq_set_wrr()
ucc_geth: Fix hangs after switching from full to half duplex
ucc_geth: Rearrange some code to avoid forward declarations
phy/marvell: Make non-aneg speed/duplex forcing work for 88E1111 PHYs
drivers/net/phy: introduce missing kfree
drivers/net/wan: introduce missing kfree
net: force bridge module(s) to be GPL
Subject: [PATCH] appletalk: Fix skb leak when ipddp interface is not loaded
...
Fixed up trivial conflicts:
- arch/x86/include/asm/socket.h
converted to <asm-generic/socket.h> in the x86 tree. The generic
header has the same new #define's, so that works out fine.
- drivers/net/tun.c
fix conflict between 89f56d1e9 ("tun: reuse struct sock fields") that
switched over to using 'tun->socket.sk' instead of the redundantly
available (and thus removed) 'tun->sk', and 2b980dbd ("lsm: Add hooks
to the TUN driver") which added a new 'tun->sk' use.
Noted in 'next' by Stephen Rothwell.
IDs should generally only be added to pci_ids.h when they're shared
across several files in the tree. IDs that are just used by a single
driver should be defined in the driver instead.
Perhaps documenting this is a good idea to prevent things being moved there,
as it still seems to be happening judging from the git log.
(based on discussion w/gregkh and others).
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Jasper Forest introduces raid offload support via ioat3.2 support. When
raid offload is enabled two (out of 8 channels) will report raid5/raid6
offload capabilities. The remaining channels will only report ioat3.0
capabilities (memcpy).
Signed-off-by: Tom Picard <tom.s.picard@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
A misconfiguration by the firmware of the U4 PCIe bridge on PowerMac G5
with the U4 bridge (latest generations, may also affect the iMac G5
"iSight") is causing us to re-assign the PCI BARs of the video card,
which can get it out of sync with the firmware, thus breaking offb.
This works around it by fixing up the bridge configuration properly
at boot time. It also fixes a bug where the firmware provides us with
an incorrect set of accessible regions in the device-tree.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch adds a new device ID for those 5785 devices that will only
use 10/100 phys.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Synced with Realtek's 6.011.00 r8169 driver.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add PCI initialization code to take control of the xHCI host controller
away from the BIOS, halt, and reset the host controller. The xHCI spec
says that BIOSes must give up the host controller within 5 seconds.
Add some host controller glue functions to handle hardware initialization
and memory allocation for the host controller. The current xHCI
prototypes use PCI interrupts, but the xHCI spec requires MSI-X
interrupts. Add code to support MSI-X interrupts, but use the PCI
interrupts for now.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (103 commits)
powerpc: Fix bug in move of altivec code to vector.S
powerpc: Add support for swiotlb on 32-bit
powerpc/spufs: Remove unused error path
powerpc: Fix warning when printing a resource_size_t
powerpc/xmon: Remove unused variable in xmon.c
powerpc/pseries: Fix warnings when printing resource_size_t
powerpc: Shield code specific to 64-bit server processors
powerpc: Separate PACA fields for server CPUs
powerpc: Split exception handling out of head_64.S
powerpc: Introduce CONFIG_PPC_BOOK3S
powerpc: Move VMX and VSX asm code to vector.S
powerpc: Set init_bootmem_done on NUMA platforms as well
powerpc/mm: Fix a AB->BA deadlock scenario with nohash MMU context lock
powerpc/mm: Fix some SMP issues with MMU context handling
powerpc: Add PTRACE_SINGLEBLOCK support
fbdev: Add PLB support and cleanup DCR in xilinxfb driver.
powerpc/virtex: Add ml510 reference design device tree
powerpc/virtex: Add Xilinx ML510 reference design support
powerpc/virtex: refactor intc driver and add support for i8259 cascading
powerpc/virtex: Add support for Xilinx PCI host bridge
...
The code is divided in two parts. There is a virtual 'bus' driver
that handles PCI device and registers three new devices one per card
reader type. The other driver handles SD/MMC part of the reader.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (290 commits)
ALSA: pcm - Update document about xrun_debug proc file
ALSA: lx6464es - support standard alsa module parameters
ALSA: snd_usb_caiaq: set mixername
ALSA: hda - add quirk for STAC92xx (SigmaTel STAC9205)
ALSA: use card device as parent for jack input-devices
ALSA: sound/ps3: Correct existing and add missing annotations
ALSA: sound/ps3: Restructure driver source
ALSA: sound/ps3: Fix checkpatch issues
ASoC: Fix lm4857 control
ALSA: ctxfi - Clear PCM resources at hw_params and hw_free
ALSA: ctxfi - Check the presence of SRC instance in PCM pointer callbacks
ALSA: ctxfi - Add missing start check in atc_pcm_playback_start()
ALSA: ctxfi - Add use_system_timer module option
ALSA: usb - Add boot quirk for C-Media 6206 USB Audio
ALSA: ctxfi - Fix wrong model id for UAA
ALSA: ctxfi - Clean up probe routines
ALSA: hda - Fix the previous tagra-8ch patch
ALSA: hda - Add 7.1 support for MSI GX620
ALSA: pcm - A helper function to compose PCM stream name for debug prints
ALSA: emu10k1 - Fix minimum periods for efx playback
...
This adds support for the following serial controller chip:
Oxford Semiconductor OXCB950 for PCI Cardbus interface
http://www.transdimension.com/products/serial/OXCB950.html
on this card:
ExSys EX-1370 1 port high-speed serial card for ExpressCard/34 slot
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes the forcedeth device ids from pci_ids.h
The forcedeth driver uses the device id constants directly in its source
file.
[ Need to keep PCI_DEVICE_ID_NVIDIA_NVENET_15 in order to keep
drivers/pci/quirks.c building -DaveM ]
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new ID is validated by Cologne Chip.
LEDs control is also supported.
Signed-off-by: Andreas Eversberg <andreas@eversberg.eu>
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
new id for HFC-8S
Signed-off-by: Andreas Eversberg <andreas@eversberg.eu>
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the PCI Device ID 0xc409 to the PCI ID table of via82cxxx.c,
as well as the 0x8409 south bridge ID.
This is required to make the IDE driver work on the VX855/VX875 integrated
chipset.
Signed-off-by: Harald Welte <HaraldWelte@viatech.com>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: Bruce Chang <BruceChang@via.com.tw>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The P2020 is a dual e500v2 core based SOC with:
* 3 PCIe controllers
* 2 General purpose DMA controllers
* 2 sRIO controllers
* 3 eTSECS
* USB 2.0
* SDHC
* SPI, I2C, DUART
* enhanced localbus
* and optional Security (P2020E) security w/XOR acceleration
The p2020 DS reference board is pretty similar to the existing MPC85xx
DS boards and has a ULI 1575 connected on one of the PCIe controllers.
Signed-off-by: Ted Peters <Ted.Peters@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds PCI IDs for MPC8569 and MPC8569E processors,
plus adds appropriate quirks for these IDs, and thus makes
PCI-E actually work on MPC8569E-MDS boards.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This adds support for the LEDs on the Jupiter netbook.
Reported-by: Martin Bammer <mrb74@gmx.at>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
prototype of a driver for the digigram lx6464es 64 channel ethersound
interface.
Signed-off-by: Tim Blechmann <tim@klingt.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Support the Intel 854 Chipset in fbdev.
We test and use the patch on a Thomson IP1101 IPTV-Box. On the VGA-Port
we get a normal signal.
Here is the link to the Mambux-Project: http://www.mambux.de
Cc: Keith Packard <keithp@keithp.com>
Cc: Dave Airlie <airlied@linux.ie>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Stefan Husemann <shusemann@googlemail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This implements basic support for all 843x RS232 devices, but does not
add DMA support. This means that sustained data transfers at high baud
rates may not be possible on multiple ports simultaneously.
Signed-off-by: Shawn Bohrer <shawn.bohrer@ni.com>
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add the PCI Device ID of the PCI Bridge Controller on AMD8111 chip.
Signed-off-by: Harry Ciao <qingtao.cao@windriver.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (88 commits)
PCI: fix HT MSI mapping fix
PCI: don't enable too much HT MSI mapping
x86/PCI: make pci=lastbus=255 work when acpi is on
PCI: save and restore PCIe 2.0 registers
PCI: update fakephp for bus_id removal
PCI: fix kernel oops on bridge removal
PCI: fix conflict between SR-IOV and config space sizing
powerpc/PCI: include pci.h in powerpc MSI implementation
PCI Hotplug: schedule fakephp for feature removal
PCI Hotplug: rename legacy_fakephp to fakephp
PCI Hotplug: restore fakephp interface with complete reimplementation
PCI: Introduce /sys/bus/pci/devices/.../rescan
PCI: Introduce /sys/bus/pci/devices/.../remove
PCI: Introduce /sys/bus/pci/rescan
PCI: Introduce pci_rescan_bus()
PCI: do not enable bridges more than once
PCI: do not initialize bridges more than once
PCI: always scan child buses
PCI: pci_scan_slot() returns newly found devices
PCI: don't scan existing devices
...
Fix trivial append-only conflict in Documentation/feature-removal-schedule.txt
Add support for the Broadcom HT1100 LD chipset (SMBus function.)
Signed-off-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The MCP78S and MCP79 appear to be compatible with the previous nForce
chips as far as the SMBus controller is concerned. The MCP67 and MCP73
were not tested yet but I'd be very surprised if they weren't
compatible too.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Oleg Ryjkov <olegr@olegr.ca>
Cc: Malcolm Lalkaka <mlalkaka@gmail.com>
Cc: Zbigniew Luszpinski <zbiggy@o2.pl>
Add vendor ID for Quanta Microsystems and update the led table with the reported device.
Reported-by: Scott Barnes <nekoreeve@gmail.com>
Signed-off-by: Tulio Magno Quites Machado Filho <tuliom@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On the Compaq Evo D510 SFF/CMT, a PCI quirk activated the SMBus device
based on detection of the on-board VGA controller, but the on-board
VGA is disabled if an AGP card is inserted, so look for one of the USB
controllers instead.
Signed-off-by: David O'Shea <dcoshea@hotmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Intel 8257x Ethernet boards have a feature called Serial Over Lan.
This feature works by emulating a serial port, and it is detected by
kernel as a normal 8250 port. However, this emulation is not perfect, as
also noticed on changeset 7500b1f602.
Before this patch, the kernel were trying to check if the serial TX is
capable of work using IRQ's.
This were done with a code similar this:
serial_outp(up, UART_IER, UART_IER_THRI);
lsr = serial_in(up, UART_LSR);
iir = serial_in(up, UART_IIR);
serial_outp(up, UART_IER, 0);
if (lsr & UART_LSR_TEMT && iir & UART_IIR_NO_INT)
up->bugs |= UART_BUG_TXEN;
This works fine for other 8250 ports, but, on 8250-emulated SoL port, the
chip is a little lazy to down UART_IIR_NO_INT at UART_IIR register.
Due to that, UART_BUG_TXEN is sometimes enabled. However, as TX IRQ keeps
working, and the TX polling is now enabled, the driver miss-interprets the
IRQ received later, hanging up the machine until a key is pressed at the
serial console.
This is the 6 version of this patch. Previous versions were trying to
introduce a large enough delay between serial_outp and serial_in(up,
UART_IIR), but not taking forever. However, the needed delay couldn't be
safely determined.
At the experimental tests, a delay of 1us solves most of the cases, but
still hangs sometimes. Increasing the delay to 5us was better, but still
doesn't solve. A very high delay of 50 ms seemed to work every time.
However, poking around with delays and pray for it to be enough doesn't
seem to be a good approach, even for a quirk.
So, instead of playing with random large arbitrary delays, let's just
disable UART_BUG_TXEN for all SoL ports.
[akpm@linux-foundation.org: fix warnings]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I have a Digi Neo 8 PCI card (114f:00b1) Serial controller: Digi
International Digi Neo 8 (rev 05)
that works with the jsm driver after using the following patch.
Signed-off-by: Adam Lackorzynski <adam@os.inf.tu-dresden.de>
Cc: Scott H Kilau <Scott_Kilau@digi.com>
Cc: Wendy Xiong <wendyx@us.ibm.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI hotplug: Change link order of pciehp & acpiphp
PCI hotplug: fakephp: Allocate PCI resources before adding the device
PCI MSI: Fix undefined shift by 32
PCI PM: Do not wait for buses in B2 or B3 during resume
PCI PM: Power up devices before restoring their state
PCI PM: Fix hibernation breakage on EeePC 701
PCI: irq and pci_ids patch for Intel Tigerpoint DeviceIDs
PCI PM: Fix suspend error paths and testing facility breakage
Add vendor ID for AMBIT and use it to set the ath5k LED gpio.
base.c:
Changes-licensed-under: 3-Clause-BSD
Signed-off-by: Tulio Magno Quites Machado Filho <tuliom@gmail.com>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add vendor ID for Foxconn and use it to set the ath5k LED gpio and
polarity for Acer branded laptops.
base.c:
Changes-licensed-under: 3-Clause-BSD
Reported-by: Maxim Levitsky <maximlevitsky@gmail.com>
Tested-by: Maxim Levitsky <maximlevitsky@gmail.com>
Tested-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for PCI-Express controllers as found on the
newer MPC83xx chips.
The work is loosely based on the Tony Li's patch[1], but unlike the
original patch, this patch implements sliding window for the Type 1
transactions using outbound window translations, so we don't have to
ioremap the whole PCI-E configuration space.
[1] http://ozlabs.org/pipermail/linuxppc-dev/2008-January/049028.html
Signed-off-by: Tony Li <tony.li@freescale.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
It supports VX855 and future chips whose IDE controller uses PCI ID 0x0571.
Signed-off-by: Joseph Chan <josephchan@via.com.tw>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Instead of making up a name for the device ids, put them directly in the
device id table. Also move the vendor id to pci_ids.h.
Signed-off-by: Cesar Eduardo Barros <cesarb@cesarb.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
On Vortex86SX with IDE controller revision 0x11 ultra DMA must be
disabled. This patch was tested by DMP and seems to work.
It is a cleaned up version of their older Kernel patch:
http://www.dmp.com.tw/tech/vortex86sx/patch-2.6.24-DMP.gz
Tested-by: Shawn Lin <shawn@dmp.com.tw>
Signed-off-by: Brandon Philips <bphilips@suse.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Support for the IT8172 IDE controller was removed from the kernel
sometime after 2.6.18. Support for the only boards that used the IT8172
was removed from the kernel after 2.6.18, as they had never compiled
since 2.6.0. However, there are a couple of platforms that use this
chip: the PMC-Sierra Xiao Hu thin-client computer, which is no longer
in production, and the Linksys NSS4000 Network Attached Storage box,
which is based on the Xiao Hu board. I am attempting to add support
for the Xiao Hu to the kernel, and this IT8172 IDE controller is the
first bit of code in this effort.
This patch resurrects the IT8172 IDE controller code. I began with
the 2.6.18 version of the it8172.c file, and have moved it forward so
that it works with the latest version of the kernel. I have run this
driver on a PMC-Sierra Xiao Hu board with the 2.6.28 kernel, and
I have had no problems with it in my configuration. The attached patch
applies cleanly against 2.6.28.
Signed-off-by: Shane McDonald <mcdonald.shane@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: alan@lxorguk.ukuu.org.uk
[bart: s/HWIF(drive)/drive->hwif/]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add support for Sealevel Systems Model 7803 COMM+8
Signed-off-by: Flavio Leitner <fleitner@redhat.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The PCI-card identified as "Oxford Semiconductor Ltd EXSYS EX-41092 Dual
16950 Serial adapter" is only usable with other devices (i.e. not the same
card) after doing a "setserial /dev/ttyS<n> baud_base 115200". This
baud_base should be default for this card.
Signed-off-by: Niels de Vos <niels.devos@wincor-nixdorf.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (123 commits)
dock: make dock driver not a module
ACPI: fix ia64 build warning
ACPI: hack around sysfs warning with link order
ACPI suspend: fix build warning when CONFIG_ACPI_SLEEP=n
intel_menlo: fix build warning
panasonic-laptop: fix build
ACPICA: Update version to 20080926
ACPICA: Add support for zero-length buffer-to-string conversions
ACPICA: New: Validation for predefined ACPI methods/objects
ACPICA: Fix for implicit return compatibility
ACPICA: Fixed a couple memory leaks associated with "implicit return"
ACPICA: Optimize buffer allocation procedure
ACPICA: Fix possible memory leak, error exit path
ACPICA: Fix fault after mem allocation failure in AML parser
ACPICA: Remove unused ACPI register bit definition
ACPICA: Update version to 20080829
ACPICA: Fix possible memory leak in acpi_ns_get_external_pathname
ACPICA: Cleanup for internal Reference Object
ACPICA: Update comments - no functional changes
ACPICA: Update for Reference ACPI_OPERAND_OBJECT
...
Add support for the OxSemi 'Tornado' devices.
Reformatted and reworked a bit by Alan Cox
Signed-off-by: Lee Howard <lee.howard@mainpine.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The Intel 7300 Memory Controller supports dynamic throttling of memory which can
be used to save power when system is idle. This driver does the memory
throttling when all CPUs are idle on such a system.
Refer to "Intel 7300 Memory Controller Hub (MCH)" datasheet
for the config space description.
Signed-off-by: Andy Henroid <andrew.d.henroid@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
This patch updates the Intel Ibex Peak (PCH) LPC and SMBus Controller
DeviceIDs.
The LPC Controller ID is set by Firmware within the range of
0x3b00-3b1f. This range is included in pci_ids.h using min and max
values, and irq.c now has code to handle the range (in lieu of 32
additions to a SWITCH statement).
The SMBus Controller ID is a fixed-value and will not change.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Support the Matrox G200eV chip, based on timings that I found in the X.org
matrox driver.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Petr Vandrovec <vandrove@vc.cvut.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'x86-v28-for-linus-phase3-B' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (74 commits)
AMD IOMMU: use iommu_device_max_index, fix
AMD IOMMU: use iommu_device_max_index
x86: add PCI IDs for AMD Barcelona PCI devices
x86/iommu: use __GFP_ZERO instead of memset for GART
x86/iommu: convert GART need_flush to bool
x86/iommu: make GART driver checkpatch clean
x86 gart: remove unnecessary initialization
x86: restore old GART alloc_coherent behavior
revert "x86: make GART to respect device's dma_mask about virtual mappings"
x86: export pci-nommu's alloc_coherent
iommu: remove fullflush and nofullflush in IOMMU generic option
x86: remove set_bit_string()
iommu: export iommu_area_reserve helper function
AMD IOMMU: use coherent_dma_mask in alloc_coherent
add AMD IOMMU tree to MAINTAINERS file
AMD IOMMU: use cmd_buf_size when freeing the command buffer
AMD IOMMU: calculate IVHD size with a function
AMD IOMMU: remove unnecessary cast to u64 in the init code
AMD IOMMU: free domain bitmap with its allocation order
AMD IOMMU: simplify dma_mask_to_pages
...
Driver for Atheros L2 10/100 network device. Includes necessary
changes for Kconfig, Makefile, and pci_ids.h.
Signed-off-by: Chris Snook <csnook@redhat.com>
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The PCI device ids for AMD family 0x11 processors are missing in pci_ids.h.
This patch adds them.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Also, stop looking at the NAND controller (0x4100) and checking the
device class. For a while during development, all three functions on the
chip had the same ID. We made them fix that fairly promptly, and we can
forget about it now.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
firewire: state userland requirements in Kconfig help
firewire: avoid memleak after phy config transmit failure
firewire: fw-ohci: TSB43AB22/A dualbuffer workaround
firewire: queue the right number of data
firewire: warn on unfinished transactions during card removal
firewire: small fw_fill_request cleanup
firewire: fully initialize fw_transaction before marking it pending
firewire: fix race of bus reset with request transmission
Preliminary support for the Intel 5100 MCH. CE and UE errors are reported
along with the current DIMM label information and other memory parameters.
Reasons why this is preliminary:
1) This chip has 2 independent memory controllers which, for best
perforance, use interleaved accesses to the DDR2 memory. This
architecture does not map very well to the current edac data structures
which depend on symmetric channel access to the interleaved data.
Without core changes, the best I could do for now is to map both memory
controllers to different csrows (first all ranks of controller 0, then
all ranks of controller 1). Someone much more familiar with the edac
core than I will probably need to come up with a more general data
structure to handle the interleaving and de-interleaving of the two
memory controllers.
2) I have not yet tackled the de-interleaving of the rank/controller
address space into the physical address space of the CPU. There is
nothing fundamentally missing, it is just ending up to be a lot of
code, and I'd rather keep it separate for now, esp since it doesn't
work yet...
3) The code depends on a particular i5100 chip select to DIMM mainboard
chip select mapping. This mapping seems obvious to me in order to
support dual and single ranked memory, but it is not unique and DIMM
labels could be wrong on other mainboards. There is no way to query
this mapping that I know of.
4) The code requires that the i5100 is in 32GB mode. Only 4 ranks per
controller, 2 ranks per DIMM are supported. I do not have hardware
(nor do I expect to have hardware anytime soon) for the 48GB (6 ranks
per controller) mode.
5) The serial presence detect code should be broken out into a "real"
i2c driver so that decode-dimms.pl can work.
Signed-off-by: Arthur Jones <ajones@riverbed.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Isochronous reception in dualbuffer mode is reportedly broken with
TI TSB43AB22A on x86-64. Descriptor addresses above 2G have been
determined as the trigger:
https://bugzilla.redhat.com/show_bug.cgi?id=435550
Two fixes are possible:
- pci_set_consistent_dma_mask(pdev, DMA_31BIT_MASK);
at least when IR descriptors are allocated, or
- simply don't use dualbuffer.
This fix implements the latter workaround.
But we keep using dualbuffer on x86-32 which won't give us highmen (and
thus physical addresses outside the 31bit range) in coherent DMA memory
allocations. Right now we could for example also whitelist PPC32, but
DMA mapping implementation details are expected to change there.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jarod Wilson <jwilson@redhat.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx: (24 commits)
I/OAT: I/OAT version 3.0 support
I/OAT: tcp_dma_copybreak default value dependent on I/OAT version
I/OAT: Add watchdog/reset functionality to ioatdma
iop_adma: cleanup iop_chan_xor_slot_count
iop_adma: document how to calculate the minimum descriptor pool size
iop_adma: directly reclaim descriptors on allocation failure
async_tx: make async_tx_test_ack a boolean routine
async_tx: remove depend_tx from async_tx_sync_epilog
async_tx: export async_tx_quiesce
async_tx: fix handling of the "out of descriptor" condition in async_xor
async_tx: ensure the xor destination buffer remains dma-mapped
async_tx: list_for_each_entry_rcu() cleanup
dmaengine: Driver for the Synopsys DesignWare DMA controller
dmaengine: Add slave DMA interface
dmaengine: add DMA_COMPL_SKIP_{SRC,DEST}_UNMAP flags to control dma unmap
dmaengine: Add dma_client parameter to device_alloc_chan_resources
dmatest: Simple DMA memcpy test client
dmaengine: DMA engine driver for Marvell XOR engine
iop-adma: fix platform driver hotplug/coldplug
dmaengine: track the number of clients using a channel
...
Fixed up conflict in drivers/dca/dca-sysfs.c manually
This patch adds to ioatdma and dca modules
support for Intel I/OAT DMA engine ver.3 (aka CB3 device).
The main features of I/OAT ver.3 are:
* 8 single channel DMA devices (8 channels total)
* 8 DCA providers, each can accept 2 requesters
* 8-bit TAG values and 32-bit extended APIC IDs
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
JMicron chips sometimes have two interfaces to work around limitations
in Microsoft's sdhci driver. This patch allows us to use either interface.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Add support for the MPC8536 process and MPC8536DS reference board. The
MPC8536 is an e500v2 based SoC which eTSEC, USB, SATA, PCI, and PCIe.
The USB and SATA IP blocks are similiar to those on the PQ2 Pro SoCs and
thus use the same drivers.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This has been sitting around unloved for way too long..
The Marvell CaFe chip's SD implementation chokes during card insertion
if one attempts to set the voltage and power up in the same
SDHCI_POWER_CONTROL register write. This adds a quirk that does
that particular dance in two steps.
It also adds an entry to pci_ids.h for the CaFe chip's SD device.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: Pierre Ossman <drzeus-list@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
