Pull workqueue fix from Tejun Heo:
"CPU hotplug callbacks can invoke DOWN_FAILED w/o preceding
DOWN_PREPARE which can trigger a WARN_ON() in workqueue.
The bug has been there for a very long time. It only triggers if CPU
down fails at a specific point and I don't think it has adverse
effects other than the warning messages. The fix is very low impact"
* 'for-4.6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: fix rebind bound workers warning
The e1000e_config_hwtstamp function was incorrectly resetting the SYSTIM
registers every time the ioctl was being run. If you happened to be
running ptp4l and lost the PTP connect (removing cable, or blocking the
UDP traffic for example), then ptp4l will eventually perform a restart
which involves re-requesting timestamp settings. In e1000e this has the
unfortunate and incorrect result of resetting SYSTIME to the kernel
time. Since kernel time is usually in UTC, and PTP time is in TAI, this
results in the leap second being re-applied.
Fix this by extracting the SYSTIME reset out into its own function,
e1000e_ptp_reset, which we call during reset to restore the hardware
registers. This function will (a) restart the timecounter based on the
new system time, (b) restore the previous PPB setting, and (c) restore
the previous hwtstamp settings.
In order to perform (b), I had to modify the adjfreq ptp function
pointer to store the old delta each time it is called. This also has the
side effect of restoring the correct base timinca register correctly.
The driver does not need to explicitly zero the ptp_delta variable since
the entire adapter structure comes zero-initialized.
Reported-by: Brian Walsh <brian@walsh.ws>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Brian Walsh <brian@walsh.ws>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for partial GSO segmentation in the case of
tunnels. Specifically with this change the driver an perform segmentation
as long as the frame either has IPv6 inner headers, or we are allowed to
mangle the IP IDs on the inner header. This is needed because we will not
be modifying any fields from the start of the start of the outer transport
header to the start of the inner transport header as we are treating them
like they are just a block of IP options.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The E1000_ICH_NVM_SIG_MASK value is shifted, out to the 31st bit, which
is the signed bit for signed constants. Mark these values as unsigned to
prevent compiler warnings and issues on platforms which a different
signed bit implementation.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This prevents signed bitshift issues when the shift would overwrite the
signed bit, and prevents making this mistake in the future when copying
and modifying code.
Use GENMASK or the unsigned postfix for cases which aren't suitable for
BIT() macro.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
To prevent signed bitshift issues, and improve code readability, use the
BIT() macro. Also make use of GENMASK or the unsigned postfix where this
is more appropriate than BIT()
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The variable rdlen is set but never used, and thus setting it is dead
code. Remove it.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Table 7-62 on page 338 of the i210 datasheet lists TX and RX latencies
for the various speeds the chip supports. To give better PTP timestamp
accuracy, adjust the timestamps by the amounts Intel gives based on
current link speed.
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A recent patch added a stub function for acpi_video_get_levels when
CONFIG_ACPI_VIDEO is disabled. However, this is marked as 'static'
and causes a warning about an unused function whereever the header
gets included:
In file included from ../drivers/gpu/drm/radeon/radeon_acpi.c:28:0:
include/acpi/video.h:74:12: error: 'acpi_video_get_levels' defined but not used [-Werror=unused-function]
This makes the declaration 'static inline', which gets rid of the
warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 059500940d (ACPI/video: export acpi_video_get_levels)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
SYSTIMH:SYSTIML registers are incremented by 24-bit value TIMINCA[23..0]
er32(SYSTIML) are probably moderately expensive (they are pci bus reads).
Can we avoid one of them? Yes, we can.
If the SYSTIML value we see is smaller than 0xff000000, the overflow
into SYSTIMH would require at least two increments.
We do two reads, er32(SYSTIML) and er32(SYSTIMH), in this order.
Even if one increment happens between them, the overflow into SYSTIMH
is impossible, and we can avoid doing another er32(SYSTIML) read
and overflow check.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If two consecutive reads of the counter are the same, it is also
not an overflow. "systimel_1 < systimel_2" should be
"systimel_1 <= systimel_2".
Before the patch, we could perform an *erroneous* correction:
Let's say that systimel_1 == systimel_2 == 0xffffffff.
"systimel_1 < systimel_2" is false, we think it's an overflow,
we read "systimeh = er32(SYSTIMH)" which meanwhile had incremented,
and use "(systimeh << 32) + systimel_2" value which is 2^32 too large.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
CC: intel-wired-lan@lists.osuosl.org
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
"incvalue" variable holds a result of "er32(TIMINCA) &
E1000_TIMINCA_INCVALUE_MASK" and used in "do_div(temp, incvalue)"
as a divisor.
Thus, "u64 incvalue" declaration is probably a mistake.
Even though it seems to be a harmless one, let's fix it.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* Change SMD callback parameters
* Use writecombine mapping for SMEM
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Jzqj
-----END PGP SIGNATURE-----
Merge tag 'qcom-soc-for-4.7-2' into net-next
This merges the Qualcomm SOC tree with the net-next, solving the
merge conflict in the SMD API between the two.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
For bitshifts, we should make use of the BIT macro when possible, and
ensure that other bitshifts are marked as unsigned. This helps prevent
signed bitshift errors, and ensures similar style.
Make use of GENMASK and the unsigned postfix where BIT() isn't
appropriate.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fixed the file to use a consistent ret_val for return value checking.
Signed-off-by: Brian Walsh <brian@walsh.ws>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes the issues for disabling auto-negotiation and forcing
speed and duplex settings for the non-copper media.
For non-copper media, e1000_get_settings should return ETH_TP_MDI_INVALID for
eth_tp_mdix_ctrl instead of ETH_TP_MDI_AUTO so subsequent e1000_set_settings
call would not fail with -EOPNOTSUPP.
e1000_set_spd_dplx should not automatically turn autoneg back on for forced
1000 Mbps full duplex settings for non-copper media.
Cc: xe-kernel@external.cisco.com
Cc: Daniel Walker <dwalker@fifo99.com>
Signed-off-by: Steve Shih <sshih@cisco.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix mips_cm_lock_other compilation error when MIPS_CM is not selected.
This was introduced in commit 23d5de8efb (MIPS: CM: Introduce core-other
locking functions)
Signed-off-by: Tony Wu <tung7970@gmail.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11698/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The genvdso program modifies the debug and stripped versions of the
VDSOs in place, and errors if the modification has already taken place.
Unfortunately this means that a rebuild which tries to rerun genvdso to
generate vdso*-image.c without also rebuilding vdso.so.dbg (for example
if genvdso.c is modified) hits a build error like this:
arch/mips/vdso/genvdso 'arch/mips/vdso/vdso.so.dbg' already contains a '.MIPS.abiflags' section
This is fixed by reorganising the rules such that unmodified .so files
have a .raw suffix, and these are copied in the same rule that runs
genvdso on the copies.
I.e. previously we had:
cmd_vdsold:
link objects -> vdso.so.dbg
cmd_genvdso:
strip vdso.so.dbg -> vdso.so
run genvdso -> vdso-image.c
and modify vdso.so.dbg and vdso.so in place
Now we have:
cmd_vdsold:
link objects -> vdso.so.dbg.raw
a new cmd_objcopy based strip rule (inspired by ARM):
strip vdso.so.dbg.raw -> vdso.so.raw
cmd_genvdso:
copy vdso.so.dbg.raw -> vdso.so.dbg
copy vdso.so.raw -> vdso.so
run genvdso -> vdso-image.c
and modify vdso.so.dbg and vdso.so in place
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13250/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If the size passed to ring_buffer_resize() is greater than MAX_LONG - BUF_PAGE_SIZE
then the DIV_ROUND_UP() will return zero.
Here's the details:
# echo 18014398509481980 > /sys/kernel/debug/tracing/buffer_size_kb
tracing_entries_write() processes this and converts kb to bytes.
18014398509481980 << 10 = 18446744073709547520
and this is passed to ring_buffer_resize() as unsigned long size.
size = DIV_ROUND_UP(size, BUF_PAGE_SIZE);
Where DIV_ROUND_UP(a, b) is (a + b - 1)/b
BUF_PAGE_SIZE is 4080 and here
18446744073709547520 + 4080 - 1 = 18446744073709551599
where 18446744073709551599 is still smaller than 2^64
2^64 - 18446744073709551599 = 17
But now 18446744073709551599 / 4080 = 4521260802379792
and size = size * 4080 = 18446744073709551360
This is checked to make sure its still greater than 2 * 4080,
which it is.
Then we convert to the number of buffer pages needed.
nr_page = DIV_ROUND_UP(size, BUF_PAGE_SIZE)
but this time size is 18446744073709551360 and
2^64 - (18446744073709551360 + 4080 - 1) = -3823
Thus it overflows and the resulting number is less than 4080, which makes
3823 / 4080 = 0
an nr_pages is set to this. As we already checked against the minimum that
nr_pages may be, this causes the logic to fail as well, and we crash the
kernel.
There's no reason to have the two DIV_ROUND_UP() (that's just result of
historical code changes), clean up the code and fix this bug.
Cc: stable@vger.kernel.org # 3.5+
Fixes: 83f40318da ("ring-buffer: Make removal of ring buffer pages atomic")
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Pull scheduler fix from Ingo Molnar:
"This is a revert to fix an interactivity problem.
The proper fixes for the problems that the reverted commit exposed are
now in sched/core (consisting of 3 patches), but were too risky for
v4.6 and will arrive in the v4.7 merge window"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
Revert "sched/fair: Fix fairness issue on migration"
Pull perf fixes from Ingo Molnar:
"An uncharacteristically large number of bugs popped up in the last
week:
- various tooling fixes, two crashes and build problems
- two Intel PT fixes
- an KNL uncore driver fix
- an Intel PMU driver fix"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf stat: Fallback to user only counters when perf_event_paranoid > 1
perf evsel: Handle EACCESS + perf_event_paranoid=2 in fallback()
perf evsel: Improve EPERM error handling in open_strerror()
tools lib traceevent: Do not reassign parg after collapse_tree()
perf probe: Check if dwarf_getlocations() is available
perf dwarf: Guard !x86_64 definitions under #ifdef else clause
perf tools: Use readdir() instead of deprecated readdir_r()
perf thread_map: Use readdir() instead of deprecated readdir_r()
perf script: Use readdir() instead of deprecated readdir_r()
perf tools: Use readdir() instead of deprecated readdir_r()
perf/core: Disable the event on a truncated AUX record
perf/x86/intel/pt: Generate PMI in the STOP region as well
perf/x86: Fix undefined shift on 32-bit kernels
perf/x86/msr: Fix SMI overflow
perf/x86/intel/uncore: Fix CHA registers configuration procedure for Knights Landing platform
perf diff: Fix duplicated output column
The ohci-platform driver can control the clock, while usb-nop-xceiv
as the PHY can control the vbus regulator. So this JZ4740-specific
glue is not needed anymore.
Signed-off-by: Maarten ter Huurne <maarten@treewalker.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13105/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The DT fragment will select the ohci-platform driver, since that can
handle the JZ4740 OHCI just fine. While I don't have a JZ4740-based
board with anything connected to the USB host controller, I did test
the generic OHCI driver successfully on a JZ4770-based board.
The device is disabled by default; boards that want to use it can
override the "status" property. The mass-production Qi LB60 boards
don't use the USB host controller.
Signed-off-by: Maarten ter Huurne <maarten@treewalker.org>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13104/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
AVT2 was a prototype board of which about 5 were made, none of which
are in use anymore.
Signed-off-by: Maarten ter Huurne <maarten@treewalker.org>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13103/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
- The Atmel sama5d2 was registering the wrong NFC device type
- On Atmel sam9x5, the power management controller had an incorrect
register area size
- On ARM64 Allwinner machine was not secting the generic irqchip
code, causing build errors in some configurations
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=HPqy
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"Three more bug fixes for ARM SoCs this week:
- The Atmel sama5d2 was registering the wrong NFC device type
- On Atmel sam9x5, the power management controller had an incorrect
register area size
- On ARM64 Allwinner machine was not secting the generic irqchip
code, causing build errors in some configurations"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: at91: sam9x5: Fix the memory range assigned to the PMC
arm64/sunxi: 4.6-rc1: Add dependency on generic irq chip
ARM: dts: at91: sama5d2: use "atmel,sama5d3-nfc" compatible for nfc
A small collection of driver specific fixes for the regulator
subsysetem:
- Fix handling of probe deferral for GPIO regulators.
- Fix a typo in the module alias for DA9053.
- Fix the definition of BUCK9 in the S2MPS11 driver. This change looks
larger than it is because an irregularity in the hardware means that
the macro used to define bucks 6-10 needs duplicating and tweaking
to have a separate macro for 9.
- Fix a series of errors in the definitions of the LDOs the AXP20x
regulators, some of which had always been present and some of which
were introduced in the merge window.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXNazxAAoJECTWi3JdVIfQd9EH/0x/3Era4ctuLFP/dKVg+lAQ
PDwgGRlHg1RVyEzzy1ZWqew//P7hgBo6urwFHjcczBE95e0bBhhMJERGnhya07uq
eWYfPARl1zHxEm0gOfLBDaFAW8YIaNyXiEsW/aTeViNIL9/HIAd/ZTZhJiDLPiAF
FdNs3yzBuAR5SHsnvCTXZY1d20LeQC6AC2nWUo2WrcyKKZZ0HamrSLP0lMq0OHVQ
n2h/8f1g9TcykakCStB/4D8vLKMt0OYmalh3Y/C/JGkWnhMoBTLRgktrNFh6lnh9
E0SnMXSuZbC9+mv8MLRHQft6XagDYzNq+odwSb9tfqbXqBdncOpvvVr6hLmzxGk=
=sVmG
-----END PGP SIGNATURE-----
Merge tag 'regulator-fix-v4.6-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"A small collection of driver specific fixes for the regulator
subsysetem:
- Fix handling of probe deferral for GPIO regulators
- Fix a typo in the module alias for DA9053
- Fix the definition of BUCK9 in the S2MPS11 driver. This change
looks larger than it is because an irregularity in the hardware
means that the macro used to define bucks 6-10 needs duplicating
and tweaking to have a separate macro for 9
- Fix a series of errors in the definitions of the LDOs the AXP20x
regulators, some of which had always been present and some of which
were introduced in the merge window"
* tag 'regulator-fix-v4.6-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: da9063: Correct module alias prefix to fix module autoloading
regulator: axp20x: Fix axp22x ldo_io registration error on cold boot
regulator: axp20x: Fix axp22x ldo_io voltage ranges
regulator: axp20x: Fix LDO4 linear voltage range
regulator: s2mps11: Fix invalid selector mask and voltages for buck9
regulator: gpio: check return value of of_get_named_gpio
This is rather too late so it'd be completely understandable if you
don't want to pull it at this point, I had thought I'd sent this earlier
but it seems I didn't. Everything has been in -next for some time now.
The main set of fixes here are mopping up some more issues with MMIO,
fixing handling of endianness configuration in DT (which just wasn't
working at all) and cases where the register and value endianness are
different.
There is also a fix for bulk register reads on SPMI.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXNaKUAAoJECTWi3JdVIfQoxEH/1DZGfeFyqhh4cdxrYz6UUr/
MbfMDR1wxNEvD4pifak6wYzQlern2Ki4J8ac72LP2OH9MYEoVs7kxESdSbqcVerc
uWQmn1qzj41hBSP5I4zmHIvYAwDry3B8mVVK9aYk+kBZLyOiw0eoMgZYyxB9cqws
pnfR4+5XHcaLGxh8QdIM7cXW1YOykXma4ivdwjwSlgWhYLGdh++j/uo9IUxqCrSa
qqxfMLPvAtEcksH8p4sJoRjibVDvzLXOvr3jMVHWyFoRGNDDB4TRiPkvydI04vYP
39pjg3c4gIAmp/RFyie1B8+zm4C+EQAkeiyH6D4jq8k9Gu6Y/XhqwFIAKtni3zg=
=k8tp
-----END PGP SIGNATURE-----
Merge tag 'regmap-fix-v4.6-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap fixes from Mark Brown:
"This is rather too late so it'd be completely understandable if you
don't want to pull it at this point, I had thought I'd sent this
earlier but it seems I didn't. Everything has been in -next for some
time now.
The main set of fixes here are mopping up some more issues with MMIO,
fixing handling of endianness configuration in DT (which just wasn't
working at all) and cases where the register and value endianness are
different.
There is also a fix for bulk register reads on SPMI"
* tag 'regmap-fix-v4.6-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: spmi: Fix regmap_spmi_ext_read in multi-byte case
regmap: mmio: Explicitly say little endian is the defualt in the bus config
regmap: mmio: Parse endianness definitions from DT
regmap: Fix implicit inclusion of device.h
regmap: mmio: Fix value endianness selection
regmap: fix documentation to match code
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=PEbo
-----END PGP SIGNATURE-----
Merge tag 'media/v4.6-6' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fix from Mauro Carvalho Chehab:
"A revert fixing a breakage that caused an OOPS on all VB2-based DVB
drivers.
We already have a proper fix, but it sounds safer to keep it being
tested for a while and not hurry, to avoid the risk of another
regression, specially since this is meant to be c/c to stable. So,
for now, let's just revert the broken patch"
* tag 'media/v4.6-6' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
Revert "[media] videobuf2-v4l2: Verify planes array in buffer dequeueing"
Pull drm fixes from Dave Airlie:
"A bunch of radeon displayport mode setting fixes, and some misc i915
fixes.
There is one revert, the MST audio code in i915 was causing some
oopses, so we've decided just to drop it until next kernel when we can
fix it properly"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/amdgpu: fix DP mode validation
drm/radeon: fix DP mode validation
drm/i915: Bail out of pipe config compute loop on LPT
drm/radeon: fix PLL sharing on DCE6.1 (v2)
drm/radeon: fix DP link training issue with second 4K monitor
Revert "drm/i915: start adding dp mst audio"
drm/i915/bdw: Add missing delay during L3 SQC credit programming
drm/i915/lvds: separate border enable readout from panel fitter
drm/i915: Update CDCLK_FREQ register on BDW after changing cdclk frequency
Pull crypto fix from Herbert Xu:
"This fixes a bug in the RSA self-test that may cause crashes on some
architectures such as SPARC"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: testmgr - Use kmalloc memory for RSA input
Now that there are different revisions of the Pistachio SoC
in circulation, add this information to the boot log to make
it easier for users to determine which hardware they have.
Signed-off-by: James Hartley <james.hartley@imgtec.com>
Signed-off-by: Ionela Voinescu <ionela.voinescu@imgtec.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13130/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The size variable to change the ring buffer in ftrace is a long. The
nr_pages used to update the ring buffer based on the size is int. On 64 bit
machines this can cause an overflow problem.
For example, the following will cause the ring buffer to crash:
# cd /sys/kernel/debug/tracing
# echo 10 > buffer_size_kb
# echo 8556384240 > buffer_size_kb
Then you get the warning of:
WARNING: CPU: 1 PID: 318 at kernel/trace/ring_buffer.c:1527 rb_update_pages+0x22f/0x260
Which is:
RB_WARN_ON(cpu_buffer, nr_removed);
Note each ring buffer page holds 4080 bytes.
This is because:
1) 10 causes the ring buffer to have 3 pages.
(10kb requires 3 * 4080 pages to hold)
2) (2^31 / 2^10 + 1) * 4080 = 8556384240
The value written into buffer_size_kb is shifted by 10 and then passed
to ring_buffer_resize(). 8556384240 * 2^10 = 8761737461760
3) The size passed to ring_buffer_resize() is then divided by BUF_PAGE_SIZE
which is 4080. 8761737461760 / 4080 = 2147484672
4) nr_pages is subtracted from the current nr_pages (3) and we get:
2147484669. This value is saved in a signed integer nr_pages_to_update
5) 2147484669 is greater than 2^31 but smaller than 2^32, a signed int
turns into the value of -2147482627
6) As the value is a negative number, in update_pages_handler() it is
negated and passed to rb_remove_pages() and 2147482627 pages will
be removed, which is much larger than 3 and it causes the warning
because not all the pages asked to be removed were removed.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=118001
Cc: stable@vger.kernel.org # 2.6.28+
Fixes: 7a8e76a382 ("tracing: unified trace buffer")
Reported-by: Hao Qin <QEver.cn@gmail.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
With all the latest fixes applied, I am still able to reproduce this
(and other) warning(s):
WARNING: CPU: 1 PID: 19684 at ../kernel/workqueue.c:4092 destroy_workqueue+0x70a/0x770()
...
Call Trace:
[<ffffffff819fee81>] ? dump_stack+0xb3/0x112
[<ffffffff8117377e>] ? warn_slowpath_common+0xde/0x140
[<ffffffff811ce68a>] ? destroy_workqueue+0x70a/0x770
[<ffffffff811739ae>] ? warn_slowpath_null+0x2e/0x40
[<ffffffff811ce68a>] ? destroy_workqueue+0x70a/0x770
[<ffffffffa0c944c9>] ? hci_unregister_dev+0x2a9/0x720 [bluetooth]
[<ffffffffa0b301db>] ? vhci_release+0x7b/0xf0 [hci_vhci]
[<ffffffffa0b30160>] ? vhci_flush+0x50/0x50 [hci_vhci]
[<ffffffff8117cd73>] ? do_exit+0x863/0x2b90
This is due to race present in the hci_unregister_dev path.
hdev->power_on work races with hci_dev_do_close. One tries to open,
the other tries to close, leading to warning like the above. (Another
example is a warning in kobject_get or kobject_put depending on who
wins the race.)
Fix this by switching those two racers to ensure hdev->power_on never
triggers while hci_dev_do_close is in progress.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The introduction of switch_mm_irqs_off() brought back an old bug
regarding the use of preempt_enable_no_resched:
As part of:
62b94a08da ("sched/preempt: Take away preempt_enable_no_resched() from modules")
the definition of preempt_enable_no_resched() is only available in
built-in code, not in loadable modules, so we can't generally use
it from header files.
However, the ARM version of finish_arch_post_lock_switch()
calls preempt_enable_no_resched() and is defined as a static
inline function in asm/mmu_context.h. This in turn means we cannot
include asm/mmu_context.h from modules.
With today's tip tree, asm/mmu_context.h gets included from
linux/mmu_context.h, which is normally the exact pattern one would
expect, but unfortunately, linux/mmu_context.h can be included from
the vhost driver that is a loadable module, now causing this compile
time error with modular configs:
In file included from ../include/linux/mmu_context.h:4:0,
from ../drivers/vhost/vhost.c:18:
../arch/arm/include/asm/mmu_context.h: In function 'finish_arch_post_lock_switch':
../arch/arm/include/asm/mmu_context.h:88:3: error: implicit declaration of function 'preempt_enable_no_resched' [-Werror=implicit-function-declaration]
preempt_enable_no_resched();
Andy already tried to fix the bug by including linux/preempt.h
from asm/mmu_context.h, but that didn't help. Arnd suggested reordering
the header files, which wasn't popular, so let's use this
workaround instead:
The finish_arch_post_lock_switch() definition is now also hidden
inside of #ifdef MODULE, so we don't see anything referencing
preempt_enable_no_resched() from a header file. I've built a
few hundred randconfig kernels with this, and did not see any
new problems.
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Russell King - ARM Linux <linux@armlinux.org.uk>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: linux-arm-kernel@lists.infradead.org
Fixes: f98db6013c ("sched/core: Add switch_mm_irqs_off() and use it in the scheduler")
Link: http://lkml.kernel.org/r/1463146234-161304-1-git-send-email-arnd@arndb.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Mediatek MT7620 SoC has syscfg0 bits where it sets the type of memory being used.
However, sometimes those bits are not set properly (reading "11"). In this case, the SoC assumes SDRAM.
The patch below reflects that.
Signed-off-by: Sashka Nochkin <linux-mips@durdom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13135/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If a kernel doesn't support MSA context (ie. CONFIG_CPU_HAS_MSA=n) then
it will only keep 64 bits per FP register in thread context, and the
calls to set_fpr64 in restore_msa_extcontext will overrun the end of the
FP register context into the FCSR & MSACSR values. GCC 6.x has become
smart enough to detect this & complain like so:
arch/mips/kernel/signal.c: In function 'protected_restore_fp_context':
./arch/mips/include/asm/processor.h:114:17: error: array subscript is above array bounds [-Werror=array-bounds]
fpr->val##width[FPR_IDX(width, idx)] = val; \
~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~
./arch/mips/include/asm/processor.h:118:1: note: in expansion of macro 'BUILD_FPR_ACCESS'
BUILD_FPR_ACCESS(64)
The only way to trigger this code to run would be for a program to set
up an artificial extended MSA context structure following a sigframe &
execute sigreturn. Whilst this doesn't allow a program to write to any
state that it couldn't already, it makes little sense to allow this
"restoration" of MSA context in a system that doesn't support MSA.
Fix this by killing a program with SIGSYS if it tries something as crazy
as "restoring" fake MSA context in this way, also fixing the build error
& allowing for most of restore_msa_extcontext to be optimised out of
kernels without support for MSA.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reported-by: Michal Toman <michal.toman@imgtec.com>
Fixes: bf82cb30c7 ("MIPS: Save MSA extended context around signals")
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Michal Toman <michal.toman@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: stable <stable@vger.kernel.org> # v4.3+
Patchwork: https://patchwork.linux-mips.org/patch/13164/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Calculate the MIPS clockevent device's min_delta_ns dynamically based on
the time it takes to perform the mips_next_event() sequence.
Virtualisation in particular makes the current fixed min_delta of 0x300
inappropriate under some circumstances, as the CP0_Count and CP0_Compare
registers may be being emulated by the hypervisor, and the frequency may
not correspond directly to the CPU frequency.
We actually use twice the median of multiple 75th percentiles of
multiple measurements of how long the mips_next_event() sequence takes,
in order to fairly efficiently eliminate outliers due to unexpected
hypervisor latency (which would need handling with retries when it
occurs during normal operation anyway).
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13176/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When estimating the clock frequency based on the RTC, take seconds into
account in case the Update In Progress (UIP) bit wasn't seen. This can
happen in virtual machines (which may get pre-empted by the hypervisor
at inopportune times) with QEMU emulating the RTC (and in fact not
setting the UIP bit for very long), especially on slow hosts such as
FPGA systems and hardware emulators. This results in several seconds
actually having elapsed before seeing the UIP bit instead of just one
second, and exaggerated timer frequencies.
While updating the comments, they're also fixed to match the code in
that the rising edge of the update flag is detected first, not the
falling edge.
The rising edge gives a more precise point to read the counters in a
virtualised system than the falling edge, resulting in a more accurate
frequency.
It does however mean that we have to also wait for the falling edge
before doing the read of the RTC seconds register, otherwise it seems to
be possible in slow hardware emulation to stray into the interval when
the RTC time is undefined during the update (at least 244uS after the
rising edge of the update flag). This can result in both seconds values
reading the same, and it wrapping to 60 seconds, vastly underestimating
the frequency.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13174/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The sampling of the GIC counter on Malta after observing a rising edge
of the RTC update flag differs slightly between the first and second
sample, with the first sample also calling gic_start_count(). The two
samples should really be taken as similarly as possible to get the most
accurate figure, so move the gic_start_count() call before detecting the
rising edge.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13173/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit 9791554b45 ("MIPS,prctl: add PR_[GS]ET_FP_MODE prctl options
for MIPS") added support for the PR_SET_FP_MODE prctl, which allows a
userland program to modify its FP mode at runtime. This is most notably
required if dynamic linking leads to the FP mode requirement changing at
runtime from that indicated in the initial executable's ELF header. In
order to avoid overhead in the general FP context restore code, it aimed
to have threads in the process become unable to enable the FPU during a
mode switch & have the thread calling the prctl syscall wait for all
other threads in the process to be context switched at least once. Once
that happens we can know that no thread in the process whose mode will
be switched has live FP context, and it's safe to perform the mode
switch. However in the (rare) case of modeswitches occurring in
multithreaded programs this can lead to indeterminate delays for the
thread invoking the prctl syscall, and the code monitoring for those
context switches was woefully inadequate for all but the simplest cases.
Fix this by broadcasting an IPI if other CPUs may have live FP context
for an affected thread, with a handler causing those CPUs to relinquish
their FPU ownership. Threads will then be allowed to continue running
but will stall on the wait_on_atomic_t in enable_restore_fp_context if
they attempt to use FP again whilst the mode switch is still in
progress. The end result is less fragile poking at scheduler context
switch counts & a more expedient completion of the mode switch.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Fixes: 9791554b45 ("MIPS,prctl: add PR_[GS]ET_FP_MODE prctl options for MIPS")
Reviewed-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: Adam Buchbinder <adam.buchbinder@gmail.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: stable <stable@vger.kernel.org> # v4.0+
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13145/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Whilst a PR_SET_FP_MODE prctl is performed there are decisions made
based upon whether the task is executing on the current CPU. This may
change if we're preempted, so disable preemption to avoid such changes
for the lifetime of the mode switch.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Fixes: 9791554b45 ("MIPS,prctl: add PR_[GS]ET_FP_MODE prctl options for MIPS")
Reviewed-by: Maciej W. Rozycki <macro@imgtec.com>
Tested-by: Aurelien Jarno <aurelien@aurel32.net>
Cc: Adam Buchbinder <adam.buchbinder@gmail.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: stable <stable@vger.kernel.org> # v4.0+
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13144/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If an address error exception occurs for a LDXC1 or SDXC1 instruction,
within the cop1x opcode space, allow it to be passed through to the FPU
emulator rather than resulting in a SIGILL. This causes LDXC1 & SDXC1 to
be handled in a manner consistent with the more common LDC1 & SDC1
instructions.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Tested-by: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13143/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Correct the cases missed with commit 9b26616c8d ("MIPS: Respect the
ISA level in FCSR handling") and prevent writes to read-only FCSR bits
there.
This in particular applies to FP context initialisation where any IEEE
754-2008 bits preset by `mips_set_personality_nan' are cleared before
the relevant ptrace(2) call takes effect and the PTRACE_POKEUSR request
addressing FPC_CSR where no masking of read-only FCSR bits is done.
Remove the FCSR clearing from FP context initialisation then and unify
PTRACE_POKEUSR/FPC_CSR and PTRACE_SETFPREGS handling, by factoring out
code from `ptrace_setfpregs' and calling it from both places.
This mostly matters to soft float configurations where the emulator can
be switched this way to a mode which should not be accessible and cannot
be set with the CTC1 instruction. With hard float configurations any
effect is transient anyway as read-only bits will retain their values at
the time the FP context is restored.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: stable@vger.kernel.org # v4.0+
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13239/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix a floating-point context restoration regression introduced with
commit 9b26616c8d ("MIPS: Respect the ISA level in FCSR handling")
that causes a Floating Point exception and consequently a kernel oops
with hard float configurations when one or more FCSR Enable and their
corresponding Cause bits are set both at a time via a ptrace(2) call.
To do so reinstate Cause bit masking originally introduced with commit
b1442d39fa ("MIPS: Prevent user from setting FCSR cause bits") to
address this exact problem and then inadvertently removed from the
PTRACE_SETFPREGS request with the commit referred above.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: stable@vger.kernel.org # v4.0+
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13238/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
- now clock nodes definition is merged with core .dtsi file
- only one rootclk is now part of DT
- clock clients also updated based on new binding doc
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Signed-off-by: Joshua Henderson <joshua.henderson@microchip.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Sandeep Sheriker <sandeepsheriker.mallikarjun@microchip.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-clk@vger.kernel.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13248/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
