Sparse reports a below warning.
tpa6130a2.c:193:33: warning: symbol 'tpa6130a2_component_driver' was not declared. Should it be static?
The symbol is just used inner the file. Forthermore, it's constant. Thus,
it's better to add static and const qualifier.
This commit adds it.
Fixes: cb7e62256e (ASoC: tpa6130a2: Register component)
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Mark Brown <broonie@kernel.org>
Code undo operations in power enable errror path explicitly, instead of
reusing power disable path and playing with return values there.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
After moving tpa6130a2 power management to DAPM, if chip can be physically
powered off (either reset_gpio is defined, or regulator indeed removes
power), then volume change no longer works unless chip is on due to
a running stream.
Fix that by entering regcache cache_only mode while chip is off.
Move regcache calls to tpa6130a2_power() to get them at driver init time
as well.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Replace goto err_gpio by return ret
Signed-off-by: Helen Koike <helen.koike@collabora.co.uk>
Tested-by: Sebastian Reichel <sre@kernel.org>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add DAPM support and updated rx51 accordingly.
As a consequence:
- the exported function tpa6130a2_stereo_enable is not needed anymore
- the mutex is dealt in the DAPM
- the power state is tracked by the DAPM
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
[koike: port for upstream]
Signed-off-by: Helen Koike <helen.koike@collabora.co.uk>
Tested-by: Sebastian Reichel <sre@kernel.org>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use snd_soc_{info,get,put}_volsw instead of custom volume functions
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
[koike: port for upstream]
Signed-off-by: Helen Koike <helen.koike@collabora.co.uk>
[On N900]
Tested-By: Sebastian Reichel <sre@kernel.org>
Reviewed-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use regmap instead of open-coding IO access and caching
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
[koike: port for upstream]
Signed-off-by: Helen Koike <helen.koike@collabora.co.uk>
[On N900]
Tested-By: Sebastian Reichel <sre@kernel.org>
Reviewed-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add tpa6130a2 controls by the component API and update rx51 accordingly
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
[koike: port for upstream]
Signed-off-by: Helen Koike <helen.koike@collabora.co.uk>
Tested-By: Sebastian Reichel <sre@kernel.org>
Reviewed-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
DECLARE_TLV_DB_RANGE() has the advantage over using TLV_DB_RANGE_HEAD()
that it automatically calculates the number of items in the TLV and is
hence less prone to manual error.
Generate using the following coccinelle script
// <smpl>
@@
declarer name DECLARE_TLV_DB_RANGE;
identifier tlv;
constant x;
@@
-unsigned int tlv[] = {
- TLV_DB_RANGE_HEAD(x),
+DECLARE_TLV_DB_RANGE(tlv,
...
-};
+);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
of_match_ptr is defined in of.h. Include it explicitly.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add device tree support to tpa6130a2 driver and document the
bindings.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Converted to use devm_gpio_request and devm_regulator_get APIs.
These are device managed and make error handling and cleanup
a bit simpler.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
module_i2c_driver makes the code simpler by eliminating module_init
and module_exit calls.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently ASoC can only add kcontrols using codec and platform component device
handles. It's also desirable to add kcontrols for DAIs (i.e. McBSP) and for
SoC card machine drivers too. This allows the kcontrol to have a direct handle to
the parent ASoC component DAI/SoC Card/Platform/Codec device and hence easily
get it's private data.
This change makes snd_soc_add_controls() static and wraps it in the folowing
calls (card and dai are new) :-
snd_soc_add_card_controls()
snd_soc_add_codec_controls()
snd_soc_add_dai_controls()
snd_soc_add_platform_controls()
This patch also does a lot of small mechanical changes in individual codec drivers
to replace snd_soc_add_controls() with snd_soc_add_codec_controls().
It also updates the McBSP DAI driver to use snd_soc_add_dai_controls().
Finally, it updates the existing machine drivers that register controls to either :-
1) Use snd_soc_add_card_controls() where no direct codec control is required.
2) Use snd_soc_add_codec_controls() where there is direct codec control.
In the case of 1) above we also update the machine drivers to get the correct
component data pointers from the kcontrol (rather than getting the machine pointer
via the codec pointer).
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The model_id is no longer needed within the platform_data
for the TPA driver since the model of TPA specified
with the device name (tpa6130a2/tpa6140a2).
Also update rx51 (the only affected user) to use the device name rather
than platform data.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use the device name and driver_data to identify
the TPA model supported by the driver.
Board files should use either "tpa6130a2" or
"tpa6140a2" as device name to specify the model
in used on the specific board.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The i2c core will clear the clientdata pointer automatically,
we don't have to set the `data' field to NULL in remove() or
if probe() failed anymore.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
sound/soc/codecs/tpa6130a2.c: In function 'tpa6130a2_add_controls':
sound/soc/codecs/tpa6130a2.c:342: warning: unused variable 'dapm'
Introduced by commit 39646871a4 ("ASoC:
tpa6130a2: Replace DAPM code with direct interface").
The DAPM code has been removed from the driver, but the
dapm struct remained.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The use of DAPM widgets, and extra routing can cause ordering
problems in the system.
Machine drivers should use the exported direct interface with
SND_SOC_DAPM_HP's event callback to manage the state of the
amplifier.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
New DAPM widgets, and paths to enable both channels at the
same time (for stereo output).
With this path the switch time difference can be avoided
between left and right channels.
The original DAPM paths can be still used, if only one of
TPA's output has been connected to a speaker, but for most of
the cases, switching to the stereo path is better.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Reduce the amount of duplicated code by using single
event handler for PGA_E to enable the needed channel.
Use the w->shift to pass the channel information to
the handler function.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Do not enable the amplifier right after the power has been
restored to the amplifier.
The DAPM_SUPPLY widget turns on the amp early in the DAPM
power walk, and the unmuting of channel happens quite late.
Keeping the amp in SW reset state ensures better muting.
In this way the pop noise coming from other components (codec)
can be filtered out.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Use simpler way to avoid setting the same power state
for the amplifier.
Simplifies the check introduced by patch:
ASoC: tpa6130a2: Fix unbalanced regulator disables
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Cc: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There is no need to include soc-dapm.h since soc.h includes it.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There are no known problems with current power-up sequence which first sets
the /shutdown pin high and then enables the supply. However, swap the order
so that the device is kept in shutdown/reset mode during the supply voltage
transition since slowly rising voltages can usually cause problems if the
device is not kept in reset.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Decoupling Dynamic Audio Power Management (DAPM) from codec devices is
required when developing ASoC further. Such as for other ASoC components to
have DAPM widgets or when extending DAPM to handle cross-device paths.
This patch decouples DAPM related variables from struct snd_soc_codec and
moves them to new struct snd_soc_dapm_context that is used to encapsulate
DAPM context of a device. ASoC core and API of DAPM functions are modified
to use DAPM context instead of codec.
This patch does not change current functionality and a large part of changes
come because of structure and internal API changes.
Core implementation is from Liam Girdwood <lrg@slimlogic.co.uk> with some
minor core changes, codecs and machine driver conversions from
Jarkko Nikula <jhnikula@gmail.com>.
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Manuel Lauss <manuel.lauss@googlemail.com>
Cc: Mike Frysinger <vapier.adi@gmail.com>
Cc: Cliff Cai <cliff.cai@analog.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Ryan Mallon <ryan@bluewatersys.com>
Cc: Timur Tabi <timur@freescale.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Arnaud Patard (Rtp) <arnaud.patard@rtp-net.org>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Jassi Brar <jassi.brar@samsung.com>
Cc: Daniel Gloeckner <dg@emlix.com>
Cc: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Patch "ASoC: tpa6130a2: Fix unbalanced regulator disables" introduced a
compiler warning "‘ret’ may be used uninitialized in this function".
Initialize ret to zero to get rid of it and making sure that the function
does not return any random error code when the code is falling through.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This driver has unbalanced regulator_disable when doing module loading and
unloading. This is because tpa6130a2_probe followed by tpa6130a2_remove
calls twice tpa6130a2_power(0). Fix this by implementing a state checking
in tpa6130a2_power.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Correct/Implement handling of broken chip.
Fail the i2c_prope if the communication with the chip
fails.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
These pins are for decoupling capacitors for the internal charge pumps
in TPA6130A2 and TPA6140A2 and not for connecting external supply.
Thanks to Eduardo Valentin <eduardo.valentin@nokia.com> for pointing out the
issue with TPA6130A2 and Ilkka Koskinen <ilkka.koskinen@nokia.com> with
TPA6140A2.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Reviewed-by: Ilkka Koskinen <ilkka.koskinen@nokia.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Codec output pin should be defined with SND_SOC_DAPM_OUTPUT as otherwise
external widgets doesn't alter the output state.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Since the functions arre only used for volume register,
change their name, and also fix them to properly
handle the cases, when via soc core the volume is
limited.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This reverts commit 6f3991152f.
Since core has now support for limiting the volume on controls this
patch is not needed. Furthermore, this patch actually prevents the core
to set new volume on the TPA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add support for platform dependent gain limiting on the
tpa6130a2 (and tpa6140a2) Headset amplifier.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Both tpa6130a2, and tpa6140a2 is supported by the
same driver, but the gain dB scaling is different on
the amplifiers.
Provide different mixer control for the chips with correct
TLV mapping.
User space will see:
"TPA6130A2 Headphone Playback Volume" in case of 6130
"TPA6140A2 Headphone Playback Volume" in case of 6140
The way machine drivers are using this amplifier remained
the same.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
